Move bootloaders reads/writes into separate functions. Instead of switching
client->addr, define new field bootloader_addr in mxt_data. Implement
lookup calculation for bootloader addresses.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The configuration is stored in NVRAM on the maXTouch chip. When the device
is reset it reports a CRC of the stored configuration values. Therefore it
isn't necessary to send the configuration on each probe - we can check the
CRC matches and avoid a timeconsuming backup/reset cycle.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The delay before the chip can be accessed after reset varies between
different chips in maXTouch family. Waiting for an interrupt and a T6
status message with the RESET bit set is a better behaviour.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rather than msleep for MXT_RESET_TIME and MXT_FWRESET_TIME during the
transition to bootloader mode and the transition back from app, wait for
the CHG assert to indicate that the transition is done.
This change replaces the msleep with a wait for completion that the
mxt_interrupt handler signals.
Also add CHG poll after last firmware frame - some bootloader versions will
assert the interrupt line after the final frame, in testing this meant that
the driver attempts to read the info block too early whilst the chip is
still resetting.
This improves firmware update time as we no longer wait longer than
necessary for each reset.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver should not immediately read bootloader status when in
Application Update Mode. The CHG line will assert when the device has made
a state transition and is ready to report a new status via i2c.
This change adds a wait for completion in mxt_check_bootloader, and changes
the mxt_interrupt handler to signal the completion.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These two object table entry fields are reported 1 less than their value.
When used, however, we always want the actual size and instances.
To keep the object size and instances 1-byte fields, and thus preserve
the object-table struct's 6-byte packed alignment, add some convenient
accessor functions that do the +1 every time these fields are accessed.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* The mapping of the GPIO numbers into the T19 status byte varies between
different maXTouch chips. Some have up to 7 GPIOs. Allowing a keycode array
of up to 8 items is simpler and more generic. So replace #define with
configurable number of keys which also allows the removal of is_tp.
* Rename platform data parameters to include "t19" to prevent confusion with
T15 key array.
* Probe aborts early on when pdata is NULL, so no need to check.
* Move "int i" to beginning of function (mixed declarations and code)
* Use API calls rather than __set_bit()
* Remove unused dev variable.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is not necessary to download these values to the maXTouch chip on every
probe, since they are stored in NVRAM. It makes life difficult when tuning
the device to keep them in sync with the config array/file, and requires a
new kernel build for minor tweaks.
These parameters only represent a tiny subset of the available
configuration options, tracking all of these options in platform data would
be a endless task. In addition, different versions of maXTouch chips may
have these values in different places or may not even have them at all.
Having these values also makes life more complex for device tree and other
platforms where having to define a static configuration isn't helpful.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Improve the suspend and resume handlers to allow the device
to wakeup the system from suspend.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get rid of the attb_read_val() platform hook. Instead, read the ATTB gpio
directly from the driver.
Fail if valid ATTB gpio is not provided by patform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Introduce helper functions to configure power and interrupt registers.
Default to IDLE mode on probe as device supports auto wakeup to ACVIE mode
on detecting finger touch.
Configure interrupt mode and polarity on start up. Power down on device
closure or module removal.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_() and friends for allocating memory, input device
and IRQ.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In case allocation via usb_alloc_coherent() fails in ims_pcu_buffers_alloc(),
the function jumps to the exit path without initializing local variable
'error' that is used as return value. Detected by Coverity - CID 1016531.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is an input driver and belongs to input not gpio.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for the 0x4004, 0x5000, and 0x5002 sensors found
on what should be the Motion R12, Fujitsu Q704, and Fujitsu T904. These
tablets use a new report ID (3) for their touch packets and a slightly
different HID descriptor format, but are otherwise largely identical in
protocol to the "MTTPC" tablets.
Note:
* The R12 uses its 0x4004 sensor for touch input only. A pen interface
is not present in its HID descriptor, though its possible a 0x4004
may be used for pen input by other tablet PCs in the future.
* The 0x5002 sensor appears to use a new report ID (8) for its pen
packets. The other sensors continue to use the traditional report
ID (2).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A few cases of incorrectly using 'le16_to_cpup' instead of
'get_unaligned_le16' have been noticed and fixed.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTbTZoAAoJEHm+PkMAQRiGLssH/3Rv6e9rAkEw9Ey0ymwGsCvf
6DEAcSgaWEyYWEU+DmkEQ3hbiOyESHFOsWE4zA2F5WY0w2Xsr+wDCS+14WCN6NHT
6sxSYGj1hd+ni6GhlGxfRpUXtY59h7TKHaaHYKPIOsO4OWXVeD53trpq416kvqal
zWkFOWeiEyeJnNKv0z0+5QWTeFDjTd1YawWcK/8kFez1Y4BXBECTgKoJaEcvowfU
j7oQ0BJxtLlxFgCB84bZTUbGuyn1x9FiS7Z2w9JcqSkTLMabFjsbA15eZIV66N4s
boaxlRvyvelR09eiiYYqOLxUmeEi1wRqtAM3yln1Y5/MX+DAmf5/sylqKtC5eLg=
=ezkr
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc5' into next
Merge with Linux 3.15-rc5 to sync up Wacom and other changes.
If the debounce time is 0 our usage of ilog2() later on in this driver will
cause undefined behavior. If CONFIG_OF=n this fact is evident to the
compiler, and it emits a call to ____ilog2_NaN() which doesn't exist. Fix
this by setting a sane default for debounce and failing to probe if
debounce is 0 in the DT.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Win8 version of the Panasonic CF-H2 includes a new Wacom device.
The pen interface appears to use the same protocol as before, but the
touch interface has been tweaked to send Win8-compatible reports.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sun4i resisitive touchscreen controller also comes with a built-in
temperature sensor. This commit adds support for it.
This commit also introduces a new "ts-attached" device-tree property,
when this is not set, the input part of the driver won't register. This way
the internal temperature sensor can be used to measure the SoC temperature
independent of there actually being a touchscreen attached to the controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Note the sun4i-ts controller is capable of detecting a second touch, but
when a second touch is present then the accuracy becomes so bad the
reported touch location is not useable.
The original android driver contains some complicated heuristics using the
aprox. distance between the 2 touches to see if the user is making a pinch
open / close movement, and then reports emulated multi-touch events around
the last touch coordinate (as the dual-touch coordinates are worthless).
These kinds of heuristics are just asking for trouble (and don't belong in
the kernel). So this driver offers straight forward, reliable single touch
functionality only.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Managed resources are becoming more and more popular in drivers. Let's
implement managed polled input devices, to complement managed regular input
devices.
Similarly to managed regular input devices only one new call
devm_input_allocate_polled_device() is added and the rest of APIs is
modified to work with both managed and non-managed devices.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Polled device's attributes controlling polling rate and whether polling is
enabled are attached to input device. We should have device core
instantiate them for us, so that they are created by the time new device
notification is sent to userspace, instead of doing it ourselves
afterwards.
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace existing gpio resource handling in the driver with managed
resources, this ensures more consistent error values and simplifies error
paths.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch simplifies GPIO handling in the driver by using GPIO functions
based on descriptors. As a result this driver now can be used for boards
without DT support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Simplify the driver by using managed resources for memory allocation of
internal structure, input device allocation and irq request.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change some dev_dbg() invocations to dev_err() ones, because they
are supposed to output error messages.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch converts descriptions of the structures defined in
linux/gpio_keys.h to follow kernel-doc format.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using devm_regulator_bulk_get() and devm_input_allocate_device() can make
the code cleaner and smaller as we do not need to manually free resources
the error and remove paths.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Nick Dyer
Iiro Valkonen
Benson Leung
Daniel Kurtz
Roger Quadros
Christian Engelmayer
Ezequiel Garcia
Jason Gerecke
Dmitry Torokhov
Stephen Boyd
Hans de Goede
Daniele Forsi
Alexander Shiyan
Jingoo Han
Sebastian Reichel
Andy Shevchenko
Fabio Estevam