A port is not necessarily assigned to a netdev. And a port does not
need to be a member of a bridge. So when iterating over all ports,
check before using the netdev and bridge_dev for a port. Otherwise we
dereference a NULL pointer.
Fixes: da9c359e19 ("net: dsa: mv88e6xxx: check hardware VLAN in use")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell chips can enable/disable the PPU on demand. This is needed
to access the PHY registers when there is no indirection mechanism.
Add two new ppu_enable and ppu_disable ops to describe this and finally
get rid of the MV88E6XXX_FLAG_PPU* flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips have different way to issue a software reset.
Old chips (such as 88E6060) have a reset bit in an ATU control register.
Newer chips moved this bit in a Global control register. Chips with
controllable PPU should reset the PPU when resetting the switch.
Add a new reset operation to implement these differences and introduce a
mv88e6xxx_software_reset() helper to wrap it conveniently.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an helper to toggle the eventual GPIO connected to the reset pin.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before resetting a switch, the ports should be set to the Disabled state
and the transmit queues should be drained.
Add an helper to explicit that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DSA_TAG_PROTO_EDSA as tag_protocol for the mv88e6097. The
initialisation was missing before.
Fixes: a1f482aa8c33 ("net: dsa: mv88e6xxx: Move the tagging protocol into info")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has a number flow control registers accessed via the
Flow Control register. Use these to set the pause control.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 has a different mechanism for configuring pause.
Refactor the code into an ops function, and for the moment, don't add
any mv88e6390 code yet.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two different rate limiting configurations, depending on the
switch generation. Refactor this into ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches support jumbo frames. Refactor this code into operations
in the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older devices have a couple of registers in global2. The mv88e6390
family has a single register in global1 behind which hides similar
configuration. Implement and op for this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips only support DSA tagging. Newer chips have both DSA and
EDSA tagging. Refactor the code by adding port functions for setting the
frame mode, egress mode, and if to forward unknown frames.
This results in the helper mv88e6xxx_6065_family() becoming unused, so
remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Verify mandatory ops for port setup
Don't set ether type for DSA port.
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips support a single tagging protocol, DSA. New chips support
both DSA and EDSA, an enhanced version. Having both as an option
changes the register layouts. Up until now, it has been assumed that
if EDSA is supported, it will be used. Hence the register layout has
been determined by which protocol should be used. However, mv88e6390
has a different implementation of EDSA, which requires we need to use
the DSA tagging. Hence separate the selection of the protocol from the
register layout.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 changes the monitor control register into the Monitor
and Management control, which is an indirection register to various
registers.
Add ops to set the CPU port and the ingress/egress port for both
register layouts, to global1
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 does not have the two registers to set the frame
priority map. Instead it has an indirection registers for setting a
number of different priority maps. Refactor the old code into an
function, implement the mv88e6390 version, and use an op to call the
right one.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g1_irq_setup() sets up chip->g1_irq.nirqs interrupt mappings,
so free the same amount. This will be 8 or 9 in practice, less than 16.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing comment for the MV88E6097 because of unification.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing definition of g1_irqs for MV88E6097.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.
Fixes: 450b05c15f ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the stats functions which access global 1 registers into
global1.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename functions to avoid _ prefix.
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics unit on the mv88e6390 needs the histogram mode to be
configured in a different register compared to other devices. Add an
ops to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename to mv88e6390_g1_stats_set_histogram
Move into global1.c
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 has a control register for what the histogram statistics
actually contain. This means the stat_snapshot method should not set
this information. So implement the 6390 stats_snapshot function without
these bits.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing the family of device belongs to helps with picking the ops
implementation which is appropriate to the device. So add a comment to
each structure of ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a stats snapshot differs between same families. Abstract this
into an ops member. At the same time, move the code into global1.[ch],
since the registers are in the global1 range.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
_mv88e6xxx_stats_wait() did not check the return value from
mv88e6xxx_g1_read(), so the compiler complained about set but unused
err.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch needs to be taken out of reset before we can read its ID
register on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeing interrupts requires switch register access to mask the
interrupts. Hence we must hold the register mutex.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not possible to use devm_request_threaded_irq() because we have
two stacked interrupt controllers in one device. The lower interrupt
controller cannot be removed until the upper is fully removed. This
happens too late with the devm API, resulting in error messages about
removing a domain while there is still an active interrupt. Swap to
using request_threaded_irq() and manage the release of the interrupt
manually.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error, remask the interrupts, release all maps, and remove the
domain. This cannot be done using the mv88e6xxx_g1_irq_free() because
some of these actions are not idempotent.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the g1 interrupt free code such that is masks any further
interrupts, and then releases the interrupt.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to remove an IRQ domain that was not created results in an
Opps. Add the necessary checks that the irqs were created before
freeing them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some architectures may not define IRQ_DOMAIN (like m32r), fixes
undefined references to IRQ_DOMAIN functions.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have a fundamental problem in how we treat the CPU port and
its VLAN membership. As soon as a second VLAN is configured to be
untagged, the CPU automatically becomes untagged for that VLAN as well,
and yet, we don't gracefully make sure that the CPU becomes tagged in
the other VLANs it could be a member of. This results in only one VLAN
being effectively usable from the CPU's perspective.
Instead of having some pretty complex logic which tries to maintain the
CPU port's default VLAN and its untagged properties, just do something
very simple which consists in neither altering the CPU port's PVID
settings, nor its untagged settings:
- whenever a VLAN is added, the CPU is automatically a member of this
VLAN group, as a tagged member
- PVID settings for downstream ports do not alter the CPU port's PVID
since it now is part of all VLANs in the system
This means that a typical example where e.g: LAN ports are in VLAN1, and
WAN port is in VLAN2, now require having two VLAN interfaces for the
host to properly terminate and send traffic from/to.
Fixes: Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPEED_UNFORCED indicates the MAC & PHY should perform
auto-negotiation to determine a speed which works. If this is called
for, don't set the force bit. If it is set, the MAC actually does
10Gbps, why the internal PHYs don't support.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent refactoring of setting the MAC configuration broke setting
of RGMII delays, via the phy-mode, on the 6351 family. Add the missing
ops to the structure.
Fixes: 7340e5ecdbb1 ("net: dsa: mv88e6xxx: setup port's MAC")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RGMII modes delays can be set via strapping pings or EEPROM.
Don't change them unless explicitly asked to change them. The recent
refactoring of setting the MAC configuration changed this behaviours,
in that CPU and DSA ports have any pre-configured RGMII delays
removed. This breaks the Armada 370RD board. Restore the previous
behaviour, in that RGMII delays are only applied/removed when
explicitly asked for via an phy-mode being PHY_INTERFACE_MODE_RGMII*
Fixes: 7340e5ecdbb1 ("net: dsa: mv88e6xxx: setup port's MAC")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have setters to configure the port's MAC, use them to
refactor the port setup and adjust_link code.
Note that port's MAC speed, duplex or RGMII delay must not be changed
unless the port's link is forced down. So wrap all that in a
mv88e6xxx_port_setup_mac function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the two bits for link, duplex or RGMII delays are used the same
way on chips supporting the said feature, the two bits for speed have
different meaning for most of the chips out there.
Speed value is stored in bits 1:0, 0x3 means unforce (normal detection).
Some chips reuse values for alternative speeds when bit 12 is set.
Newer chips with speed > 1Gbps reuse value 0x3 thus need a new bit 13.
Here are the values to write in register 0x1 to (un)force speed:
| Speed | 88E6065 | 88E6185 | 88E6352 | 88E6390 | 88E6390X |
| ------- | ------- | ------- | ------- | ------- | -------- |
| 10 | 0x0000 | 0x0000 | 0x0000 | 0x2000 | 0x2000 |
| 100 | 0x0001 | 0x0001 | 0x0001 | 0x2001 | 0x2001 |
| 200 | 0x0002 | NA | 0x1001 | 0x3001 | 0x3001 |
| 1000 | NA | 0x0002 | 0x0002 | 0x2002 | 0x2002 |
| 2500 | NA | NA | NA | 0x3003 | 0x3003 |
| 10000 | NA | NA | NA | NA | 0x2003 |
| unforce | 0x0003 | 0x0003 | 0x0003 | 0x0000 | 0x0000 |
This patch implements a generic mv88e6xxx_port_set_speed() function used
by chip-specific wrappers to filter supported ports and speeds.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips such as 88E6352 and 88E6390 can be programmed to add delays
to RXCLK for IND inputs or to GTXCLK for OUTD outputs when port is in
RGMII mode.
Add a port function to program such delays according to the provided PHY
interface mode.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to port's link, add setter to force port's half duplex, full
duplex or let normal duplex detection occurs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the chips will have a port register control bits to force the
port's link up, down, or let normal link detection occurs.
Implement such operation to use it later when setting duplex, etc.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port functions to set the port 802.1Q mode.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port functions to access the ports default VID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn
Vivien Didelot
Stefan Eichenberger
Andreas Färber
Florian Fainelli
David S. Miller