The NAND_CMD_SET_FEATURES support is missing from denali_cmdfunc().
We also see /* TODO: Read OOB data */ comment.
It would be possible to add more commands along with the current
implementation, but having ->cmd_ctrl() seems a better approach from
the discussion with Boris [1].
Rely on the default ->cmdfunc() from the framework and implement the
driver's own ->cmd_ctrl().
This transition also fixes NAND_CMD_STATUS and NAND_CMD_PARAM handling.
NAND_CMD_STATUS was just faked by the register read, so the only valid
bit was the WP bit. NAND_CMD_PARAM was completely broken; not only the
command sent on the bus was NAND_CMD_STATUS instead of NAND_CMD_PARAM,
but also the driver was only reading 8 bytes, while the parameter page
contains several hundreds of bytes.
Also add ->write_byte(), which is needed for write direction commands,
->read/write_buf(16), which will be used some commits later.
->read_word() is not used for now, but the core may call it in the
future.
Now, this driver can drop nand_onfi_get_set_features_notsupp().
[1] https://lkml.org/lkml/2017/3/15/97
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Simplify the interrupt handling and fix issues:
- The register field view of INTR_EN / INTR_STATUS is different
among IP versions. The global macro DENALI_IRQ_ALL is hard-coded
for Intel platforms. The interrupt mask should be determined at
run-time depending on the running platform.
- wait_for_irq() loops do {} while() until interested flags are
asserted. The logic can be simplified.
- The spin_lock() guard seems too complex (and suspicious in a race
condition if wait_for_completion_timeout() bails out by timeout).
- denali->complete is reused again and again, but reinit_completion()
is missing. Add it.
Re-work the code to make it more robust and easier to handle.
While we are here, also rename the jump label "failed_req_irq" to
more appropriate "disable_irq".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Handling timing parameters in a driver's own way should be avoided
because it duplicates efforts of drivers/mtd/nand/nand_timings.c
Besides, this driver hard-codes Intel specific parameters such as
CLK_X=5, CLK_MULTI=4. Taking a certain device (Samsung K9WAG08U1A)
into account by get_samsung_nand_para() is weird as well.
Now, the core framework provides .setup_data_interface() hook, which
handles timing parameters in a generic manner.
While I am working on this, I found even more issues in the current
code, so fixed the following as well:
- In recent IP versions, WE_2_RE and TWHR2 share the same register.
Likewise for ADDR_2_DATA and TCWAW, CS_SETUP_CNT and TWB. When
updating one, the other must be masked. Otherwise, the other will
be set to 0, then timing settings will be broken.
- The recent IP release expanded the ADDR_2_DATA to 7-bit wide.
This register is related to tADL. As commit 74a332e78e ("mtd:
nand: timings: Fix tADL_min for ONFI 4.0 chips") addressed, the
ONFi 4.0 increased the minimum of tADL to 400 nsec. This may not
fit in the 6-bit ADDR_2_DATA in older versions. Check the IP
revision and handle this correctly, otherwise the register value
would wrap around.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The function find_valid_banks() issues the Read ID (0x90) command,
then compares the first byte (Manufacturer ID) of each bank with
the one of bank0.
This is equivalent to what nand_scan_ident() does. The number of
chips is detected there, so this is unneeded.
What is worse for find_valid_banks() is that, if multiple chips are
connected to INTEL_CE4100 platform, it crashes the kernel by BUG().
This is what we should avoid. This function is just harmful and
unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The denali_cmdfunc() actually does nothing valuable for
NAND_CMD_{PAGEPROG,READ0,SEQIN}.
For NAND_CMD_{READ0,SEQIN}, it copies "page" to "denali->page", then
denali_read_page(_raw) compares them just for the sanity check.
(Inconsistently, this check is missing from denali_write_page(_raw).)
The Denali controller is equipped with high level read/write interface,
so let's skip unneeded call of cmdfunc().
If NAND_ECC_CUSTOM_PAGE_ACCESS is set, nand_write_page() will not
call ->waitfunc hook. So, ->write_page(_raw) hooks should directly
return -EIO on failure. The error handling of page writes will be
much simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Atmel NAND driver doesn't used anything from
linux/platform_data/atmel.h, stop including it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add two compatible strings for UniPhier SoC family.
"socionext,uniphier-denali-nand-v5a" is used on UniPhier sLD3, LD4,
Pro4, sLD8.
"socionext,uniphier-denali-nand-v5b" is used on UniPhier Pro5, PXs2,
LD6b, LD11, LD20.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Denali IP can automatically detect device parameters such as
page size, oob size, device width, etc. and this driver currently
relies on it. However, this hardware function is known to be
problematic.
[1] Due to a hardware bug, various misdetected cases were reported.
That is why get_toshiba_nand_para() and get_hynix_nand_para()
exist to fix-up the misdetected parameters. It is not realistic
to add a new NAND device to the *black list* every time we are
hit by a misdetected case. We would never be able to guarantee
that all cases are covered.
[2] Because this feature is unreliable, it is disabled on some
platforms.
The nand_scan_ident() detects device parameters in a more tested
way. The hardware should not set the device parameter registers in
a different, unreliable way. Instead, set the parameters from the
nand_scan_ident() back to the registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver was originally written for the Intel MRST platform with
several platform-specific parameters hard-coded.
Currently, the ECC settings are hard-coded as follows:
#define ECC_SECTOR_SIZE 512
#define ECC_8BITS 14
#define ECC_15BITS 26
Therefore, the driver can only support two cases.
- ecc.size = 512, ecc.strength = 8 --> ecc.bytes = 14
- ecc.size = 512, ecc.strength = 15 --> ecc.bytes = 26
However, these are actually customizable parameters, for example,
UniPhier platform supports the following:
- ecc.size = 1024, ecc.strength = 8 --> ecc.bytes = 14
- ecc.size = 1024, ecc.strength = 16 --> ecc.bytes = 28
- ecc.size = 1024, ecc.strength = 24 --> ecc.bytes = 42
So, we need to handle the ECC parameters in a more generic manner.
Fortunately, the Denali User's Guide explains how to calculate the
ecc.bytes. The formula is:
ecc.bytes = 2 * CEIL(13 * ecc.strength / 16) (for ecc.size = 512)
ecc.bytes = 2 * CEIL(14 * ecc.strength / 16) (for ecc.size = 1024)
For DT platforms, it would be reasonable to allow DT to specify ECC
strength by either "nand-ecc-strength" or "nand-ecc-maximize". If
none of them is specified, the driver will try to meet the chip's ECC
requirement.
For PCI platforms, the max ECC strength is used to keep the original
behavior.
Newer versions of this IP need ecc.size and ecc.steps explicitly
set up via the following registers:
CFG_DATA_BLOCK_SIZE (0x6b0)
CFG_LAST_DATA_BLOCK_SIZE (0x6c0)
CFG_NUM_DATA_BLOCKS (0x6d0)
For older IP versions, write accesses to these registers are just
ignored.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
struct nand_ecc_caps was designed as flexible as possible to support
multiple stepsizes (like sunxi_nand.c).
So, we need to write multiple arrays even for the simplest case.
I guess many controllers support a single stepsize, so here is a
shorthand macro for the case.
It allows to describe like ...
NAND_ECC_CAPS_SINGLE(denali_pci_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);
... instead of
static const int denali_pci_ecc_strengths[] = {8, 15};
static const struct nand_ecc_step_info denali_pci_ecc_stepinfo = {
.stepsize = 512,
.strengths = denali_pci_ecc_strengths,
.nstrengths = ARRAY_SIZE(denali_pci_ecc_strengths),
};
static const struct nand_ecc_caps denali_pci_ecc_caps = {
.stepinfos = &denali_pci_ecc_stepinfo,
.nstepinfos = 1,
.calc_ecc_bytes = denali_calc_ecc_bytes,
};
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Driver are responsible for setting up ECC parameters correctly.
Those include:
- Check if ECC parameters specified (usually by DT) are valid
- Meet the chip's ECC requirement
- Maximize ECC strength if NAND_ECC_MAXIMIZE flag is set
The logic can be generalized by factoring out common code.
This commit adds 3 helpers to the NAND framework:
nand_check_ecc_caps - Check if preset step_size and strength are valid
nand_match_ecc_req - Match the chip's requirement
nand_maximize_ecc - Maximize the ECC strength
To use the helpers above, a driver needs to provide:
- Data array of supported ECC step size and strength
- A hook that calculates ECC bytes from the combination of
step_size and strength.
By using those helpers, code duplication among drivers will be
reduced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use BIT() and GENMASK() for register field macros. This will make
it easier to compare the macros with the register description in the
Denali User's Guide.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
No need to use two struct resource pointers. Just reuse one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This makes it easier to grep.
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If we see unrecoverable ECC error, we need to count number of bitflips
from all-ones and report correctable/uncorrectable according to
that. Otherwise we report ECC failed on erased flash with single bit error.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reported-by: Darwin Dingel <Darwin.Dingel@alliedtelesis.co.nz>
Acked-by: Darwin Dingel <Darwin.Dingel@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
MT2712 NAND FLASH Controller is similar to MT2701 except those following:
(1) MT2712 supports up to 148B spare size per 1KB size sector (the same
with 74B spare size per 512B size sector). There are three new spare
format: 61, 67, 74.
(2) MT2712 supports up to 80 bit ecc strength. There are three new ecc
strength level: 68, 72, 80.
(3) MT2712 ECC encode parity data register's start offset is 0x300, and
different with 0x10 of MT2701.
(4) MT2712 improves ecc irq function. When ECC works in ECC_NFI_MODE,
MT2701 will generate ecc irq number the same with ecc steps during
page read. However, MT2712 can only generate one ecc irq.
Changes of this patch are:
(1) add two new variables named pg_irq_sel, encode_parity_reg0 in struct
mtk_ecc_caps.
(2) add new bitfield ECC_PG_IRQ_SEL for register ECC_IRQ_REG.
(3) add ecc strength array of mt2712.
(4) add spare size array of mt2712.
(5) add mt2712 nfc and ecc device compatiable and data.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
ECC strength and spare size supported may be different among MTK NAND
FLASH Controller IPs.
This patch contains changes as following:
(1) add new struct mtk_nfc_caps to support different spare size.
(2) add new struct mtk_ecc_caps to support different ecc strength.
(3) remove ECC_CNFG_xBIT define, use a for loop to do ecc strength config.
(4) remove PAGEFMT_SPARE_ define, use a for loop to do spare format config.
(5) malloc ecc->eccdata buffer according to max ecc strength of this IP.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The register NFI_PAGEFMT is always 32 bits length, so it is better to
do register program using writel() compare with writew().
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The newly added suspend/resume support causes a harmless warning:
drivers/mtd/nand/atmel/nand-controller.c:2513:12: error: 'atmel_nand_controller_resume' defined but not used [-Werror=unused-function]
This shuts up the warning with a __maybe_unused annotation.
Fixes: b107007a7114 ("mtd: nand: atmel: Add PM ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Drivers are supposed to set correct ecc->{size,strength,bytes} before
calling nand_scan_tail(), but it does not complain about ecc->total
bigger than oobsize.
In this case, chip->scan_bbt() crashes due to memory corruption, but
it is hard to debug. It would be kind to fail it earlier with a clear
message.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
READ0 is sometimes used to exit GET STATUS mode. When this is the case
no address cycles are requested, and we can use this information to
detect that READSTART should not be issued after READ0 or that we
shouldn't wait for the chip to be ready.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Drivers setting NAND_ECC_CUSTOM_PAGE_ACCESS are supposed to handle the
full read/write page sequence, and waiting for a page to actually be
programmed is part of this write-page sequence.
This is also what is done in ->write_oob_xxx() hooks, so let's do that in
->write_page_xxx() as well to make it consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
SEQIN is supposed to be used when one wants to start programming a page.
What we want here is just to change the column within the page, which is
done with the RNDIN command.
Fixes: 6956e2385a ("mtd: nand: add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
The core already sends the NAND_CMD_READ0 for us. Duplicating this call
in the driver is useless and introduces a perf penalty.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
ecc->read_subpage is set to sunxi_nfc_hw_ecc_read_subpage_dma when
->dmac != NULL, but is then unconditionally overwritten in the common
init path.
Remove this extra assignment to allow usage of the DMA operation when
possible.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ->errstat() hook is no longer implemented NAND controller drivers.
Get rid of it before someone starts abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cached programming is always skipped, so drop the associated code until
we decide to really support it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Provide a ->resume() hook to make sure the NAND timings are correctly
restored by resetting all chips connected to the controller.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND controller IP can adapt the NAND controller timings dynamically.
Implement the ->setup_data_interface() hook to support this feature.
Note that it's not supported on at91rm9200 because this SoC has a
completely different SMC block, which is not supported yet.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some NAND controllers can assign different NAND timings to different
CS lines. Pass the CS line information to ->setup_data_interface() so
that the NAND controller driver knows which CS line is concerned by
the setup_data_interface() request.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The only user of gpmi_nand_exit() is gpmi_nand_remove(). Move its content
to the caller.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
The GPMI driver is wrongly assuming that nand_release() can safely be
called on an uninitialized/unregistered NAND device.
Add a new err_nand_cleanup label in the error path and only execute if
nand_scan_tail() succeeded.
Note that we now call nand_cleanup() instead of nand_release()
(nand_release() is actually grouping the mtd_device_unregister() and
nand_cleanup() in one call) because there's no point in trying to
unregister a device that has never been registered.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
The clock requirements are completely missing, add the clocks
currently required by the driver.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add support for i.MX 7 SoC. The i.MX 7 has a slightly different
clock architecture requiring only two clocks to be referenced.
The IP is slightly different compared to i.MX 6, but currently none
of this differences are in use, therefore reuse GPMI_IS_MX6.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add device specific list of clocks required, and handle all clocks
in a single for loop. This avoids further code duplication when
adding i.MX 7 support.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If we see ~0UL in flash, there's no need for hweight, and no need to
check number of bitflips. So this should be net win.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This commit adjusts the fsmc_nand driver so that it accepts the
NAND_ECC_ON_DIE case. It simply does nothing in this case, since both
the ECC operations and OOB layout will be defined by the NAND chip code
rather than by the NAND controller code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now that the core NAND subsystem has support for on-die ECC, this commit
brings the necessary code to support on-die ECC on Micron NANDs.
In micron_nand_init(), we detect if the Micron NAND chip supports on-die
ECC mode, by checking a number of conditions:
- It must be an ONFI NAND
- It must be a SLC NAND
- Enabling *and* disabling on-die ECC must work
- The on-die ECC must be correcting 4 bits per 512 bytes of data. Some
Micron NAND chips have an on-die ECC able to correct 8 bits per 512
bytes of data, but they work slightly differently and therefore we
don't support them in this patch.
Then, if the on-die ECC cannot be disabled (some Micron NAND have on-die
ECC forcefully enabled), we bail out, as we don't support such
NANDs. Indeed, the implementation of raw_read()/raw_write() make the
assumption that on-die ECC can be disabled. Support for Micron NANDs
with on-die ECC forcefully enabled can easily be added, but in the
absence of such HW for testing, we preferred to simply bail out.
If the on-die ECC is supported, and requested in the Device Tree, then
it is indeed enabled, by using custom implementations of the
->read_page(), ->read_page_raw(), ->write_page() and ->write_page_raw()
operation to properly handle the on-die ECC.
In the non-raw functions, we need to enable the internal ECC engine
before issuing the NAND_CMD_READ0 or NAND_CMD_SEQIN commands, which is
why we set the NAND_ECC_CUSTOM_PAGE_ACCESS option at initialization
time (it asks the NAND core to let the NAND driver issue those
commands).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A lot of drivers are providing their own ->cmdfunc(), and most of the
time this implementation does not support all possible NAND operations.
But since ->cmdfunc() cannot return an error code, the core has no way
to know that the operation it requested is not supported.
This is a problem we cannot address for all kind of operations with the
current design, but we can prevent these silent failures for the
GET/SET FEATURES operation by overloading the default
->onfi_{set,get}_features() methods with one returning -ENOTSUPP.
Reported-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
The nand_read_page_raw() and nand_write_page_raw() functions might be
re-used by vendor-specific implementations of the read_page/write_page
functions. Instead of having vendor-specific code duplicate this code,
it is much better to export those functions and allow them to be
re-used.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A number of NAND flashes have a capability called "on-die ECC" where the
NAND chip itself is capable of detecting and correcting errors.
Linux already has support for using the ECC implementation of the NAND
controller, or a software based ECC implementation, but not for using
the ECC implementation of the NAND controller. However, such an
implementation is sometimes useful in situations where the NAND
controller provides ECC algorithms that are not strong enough for the
NAND chip used on the system. A typical case is a NAND chip that
requires a 4-bit ECC, while the NAND controller only provides a 1-bit
ECC algorithm.
This commit introduces the support for the NAND_ECC_ON_DIE ECC mode:
- Parsing of the "on-die" value for the "nand-ecc-mode" Device Tree
property
- Handling NAND_ECC_ON_DIE case in nand_scan_tail(). The idea is that
the vendor specific code for the NAND chip must implement
->read_page() and ->write_page(). It may optionally provide its own
->read_page_raw() and ->write_page_raw() as well. For OOB operation,
we assume the standard operations are good enough, but they can be
overridden by the vendor specific code if needed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A number of NAND chips support a feature called on-die ECC, where the
NAND chip itself is capable of doing error detection and correction. The
new "on-die" value for nand-ecc-mode indicates that we want this
functionality to be used.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When timings are no longer provided by the Device Tree, we now use the
SDR timings specified by the NAND flash, and such SDR timings are always
provided. Therefore, it is no longer necessary to keep "default" timings
in the fmsc driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Until now, the fsmc_nand driver was either using controller timings
specified in the Device Tree (through FSMC specific DT properties) or
alternatively default/fallback timings.
This commit implements support to use the timings advertised by the NAND
chip itself, by implementing the ->setup_data_interface() hook. To
preserve backward compatibility, if timings are specified in the Device
Tree, we use the timings from the Device Tree (and don't implement
->setup_data_interface).
Many thanks to Boris Brezillon for coming up with the logic to convert
the NAND chip timings into the timings expected by the FSMC controller.
Also, since the timings are now not only coming from the DT, the message
warning that default timings will be used is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In preparation for the introduction of support for using SDR timings
exposed by the NAND flash instead of hard-coded timings, this commit
reworks the fsmc_nand_setup() function to take a "struct fsmc_nand_data"
as argument, which already contains the I/O registers base address, bank
and bus width information.
The timings is also currently contained in the "struct fsmc_nand_data",
but we still pass it as a separate argument because the support for
using SDR timings will pass a different value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If ECC strength is 4bits/512bytes the algorithm of the ECC engine is
BCH, otherwise (1bit/512bytes) Hamming is used.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_set_ooblayout() accesor has been added to hide internals of
mtd_info and ease future refactoring. Call mtd_set_ooblayout() instead of
directly accessing mtd->ooblayout.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Harvey Hunt <harveyhuntnexus@gmail.com>
Masahiro Yamada
Alexandre Belloni
Matthias Lange
Arvind Yadav
Boris Brezillon
Xiaolei Li
Arnd Bergmann
Stefan Agner
Pavel Machek
Thomas Petazzoni
Alexander Couzens