Граф коммитов

9 Коммитов

Автор SHA1 Сообщение Дата
Sean MacLennan cd64d1697c powerpc: mtmsrd not defined
Replace the BOOK3S_64 specific mtmsrd with the generic MTMSRD macro.
Only enable ldstfp when CONFIG_PPC_FPU is set.

Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2010-09-02 14:07:34 +10:00
Paul Mackerras 0016a4cf55 powerpc: Emulate most Book I instructions in emulate_step()
This extends the emulate_step() function to handle a large proportion
of the Book I instructions implemented on current 64-bit server
processors.  The aim is to handle all the load and store instructions
used in the kernel, plus all of the instructions that appear between
l[wd]arx and st[wd]cx., so this handles the Altivec/VMX lvx and stvx
and the VSX lxv2dx and stxv2dx instructions (implemented in POWER7).

The new code can emulate user mode instructions, and checks the
effective address for a load or store if the saved state is for
user mode.  It doesn't handle little-endian mode at present.

For floating-point, Altivec/VMX and VSX instructions, it checks
that the saved MSR has the enable bit for the relevant facility
set, and if so, assumes that the FP/VMX/VSX registers contain
valid state, and does loads or stores directly to/from the
FP/VMX/VSX registers, using assembly helpers in ldstfp.S.

Instructions supported now include:
* Loads and stores, including some but not all VMX and VSX instructions,
  and lmw/stmw
* Atomic loads and stores (l[dw]arx, st[dw]cx.)
* Arithmetic instructions (add, subtract, multiply, divide, etc.)
* Compare instructions
* Rotate and mask instructions
* Shift instructions
* Logical instructions (and, or, xor, etc.)
* Condition register logical instructions
* mtcrf, cntlz[wd], exts[bhw]
* isync, sync, lwsync, ptesync, eieio
* Cache operations (dcbf, dcbst, dcbt, dcbtst)

The overflow-checking arithmetic instructions are not included, but
they appear not to be ever used in C code.

This uses decimal values for the minor opcodes in the switch statements
because that is what appears in the Power ISA specification, thus it is
easier to check that they are correct if they are in decimal.

If this is used to single-step an instruction where a data breakpoint
interrupt occurred, then there is the possibility that the instruction
is a lwarx or ldarx.  In that case we have to be careful not to lose the
reservation until we get to the matching st[wd]cx., or we'll never make
forward progress.  One alternative is to try to arrange that we can
return from interrupts and handle data breakpoint interrupts without
losing the reservation, which means not using any spinlocks, mutexes,
or atomic ops (including bitops).  That seems rather fragile.  The
other alternative is to emulate the larx/stcx and all the instructions
in between.  This is why this commit adds support for a wide range
of integer instructions.

Signed-off-by: Paul Mackerras <paulus@samba.org>
2010-06-22 19:40:29 +10:00
Ananth N Mavinakayanahalli eef336189b powerpc: Don't emulate mr. instructions
Currently emulate_step() emulates mr. instructions without updating cr0
and this can be disastrous. Don't emulate mr.

This bug has been around for a while, but I am not sure if its a worthy
-stable candidate. I'll leave it to Ben do decide.

Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-02-10 14:39:07 +11:00
Ananth N Mavinakayanahalli 6888199f7f [POWERPC] Emulate more instructions in software
Emulate a few more instructions in software - especially useful during
singlestepping (xmon/kprobes).

Instructions emulated with this patch are mfcr/mtcr rX, mfxer/mtxer rX,
mflr/mtlr rX, mfctr/mtctr rX and mr rA,rB.

Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2007-04-24 21:31:57 +10:00
Gui,Jian 0d69a052d4 [POWERPC] Disallow kprobes on emulate_step and branch_taken
On powerpc, probing on emulate_step function will crash 2.6.18.1 when
it is triggered.

When kprobe is triggered, emulate_step() is on its kernel path and
will cause recursive kprobe fault.  And branch_taken() is called
in emulate_step().  This disallows kprobes on both of them.

Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-11-01 15:14:12 +11:00
Jörn Engel 6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Stephen Rothwell af308377e2 [PATCH] powerpc: fix various sparse warnings
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2006-03-27 14:48:08 +11:00
Paul Mackerras c032524f0d powerpc: Make single-stepping emulation (mostly) usable on 32-bit
The sc instruction emulation can't be done the same way on 32-bit
as 64-bit yet, but this should work OK.

Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-10-28 22:48:08 +10:00
Paul Mackerras 14cf11af6c powerpc: Merge enough to start building in arch/powerpc.
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files.  It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac.  This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.

For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel.  This makes some minor changes
to files in those directories and files outside arch/powerpc.

The boot directory is still not merged.  That's going to be interesting.

Signed-off-by: Paul Mackerras <paulus@samba.org>
2005-09-26 16:04:21 +10:00