The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such as flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0. The
controller can also operate in Single or Dual data rate modes.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree. Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixing/optimizing bcm_qspi_bspi_read() performance introduced two
changes:
1) It added a loop to read all requested data using multiple BSPI ops.
2) It bumped max size of a single BSPI block request from 256 to 512 B.
The later change resulted in occasional BSPI timeouts causing a
regression.
For some unknown reason hardware doesn't always handle reads as expected
when using 512 B chunks. In such cases it may happen that BSPI returns
amount of requested bytes without the last 1-3 ones. It provides the
remaining bytes later but doesn't raise an interrupt until another LR
start.
Switching back to 256 B reads fixes that problem and regression.
Fixes: 345309fa7c ("spi: bcm-qspi: Fix bcm_qspi_bspi_read() performance")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
During implementation of the new API bcm_qspi_bspi_set_flex_mode() has
been modified breaking calculation of address length. An unnecessary
multiplication was added breaking flash reads.
Fixes: 5f195ee7d8 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
spidev will make a big fuss if a device tree node binds a device by
using "spidev" as the node's compatible property.
However, the logic for this isn't looking for "spidev" in the
compatible, but rather checking that the device is NOT compatible with
spidev's list of devices.
This causes a false positive if a device not named "rohm,dh2228fv", etc.
binds to spidev, even if a means other than putting "spidev" in the
device tree was used. E.g., the sysfs driver_override attribute.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This attribute works the same was as the identically named attribute
for PCI, AMBA, and platform devices. For reference, see:
commit 3cf3857134 ("ARM: 8256/1: driver coamba: add device binding
path 'driver_override'")
commit 3d713e0e38 ("driver core: platform: add device binding path
'driver_override'")
commit 782a985d7a ("PCI: Introduce new device binding path using
pci_dev.driver_override")
If the name of a driver is written to this attribute, then the device
will bind to the named driver and only the named driver.
The device will bind to the driver even if the driver does not list the
device in its id table. This behavior is different than the driver's
bind attribute, which only allows binding to devices that are listed as
supported by the driver.
It can be used to bind a generic driver, like spidev, to a device.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain devices don't work well when a transmit FIFO underrun or
receive FIFO overrun occurs. Example is the SAF400x radio chip when
running at high speed which leads to garbage being sent to/received from
the chip. In which case, it should stall waiting for further data to be
available before proceeding. This patch unset the NOSTALL bit in CFGR1
by default to prevent this issue.
Signed-off-by: Hieu Tran Dang <dangtranhieu2012@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/spi/spi-ep93xx.c:342:62: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:428:58: note: expanded from macro
'dma_map_sg'
#define dma_map_sg(d, s, n, r) dma_map_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:348:57: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:377:56: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
3 warnings generated.
dma_{,un}map_sg expect an enum of type dma_data_direction but this
driver uses dma_transfer_direction for everything. Convert the driver to
use dma_data_direction for these two functions.
There are two places that strictly require an enum of type
dma_transfer_direction: the direction member in struct dma_slave_config
and the direction parameter in dmaengine_prep_slave_sg. To avoid using
an explicit cast, add a simple function, ep93xx_dma_data_to_trans_dir,
to safely map between the two types because they are not 1 to 1 in
meaning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this commit the DSPI driver on the BK4 board can be used for SPI
transmission managed from user space (via /dev/spidev0.0).
Example usage/testing:
insmod ./spi-fsl-dspi.ko
./spidev_test -D /dev/spidev0.0 -s 3000000 -v -H -b 8 -p "\xCC\x11\x22\x74"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rewrite switch code block to directly do the expected number
of shifts in each case and have break statements.
Addresses-Coverity-ID: 1056539 ("Missing break in switch")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apparently, this code does not actually fall through to the next case
because the machine restarts before it has a chance. However, for the
sake of maintenance and readability, we better add the missing break
statement.
Addresses-Coverity-ID: 1437892 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added spi-mem
code. The Tegra fix is relatively large but fairly straightforward and
mechanical, it runs on probe so it's been reasonably well covered in
-next testing.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuOnETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AhkB/9ahKdmxdxu0uuzzvS5qmdGD+98dTaV
M+7+Bq6CJfBz0YTc9dxTiynbJot15vo5mKDZkDaJrgOoLCWWDGWa/DjRif2qS2o9
QxjWlBPzfOhKb81/HMJ+MaIHYDtAxvCu4iZExUZPxZzypX8Q9U3+9a/u0+JnRug2
guQ/4vYdxTGbR/taFsKLzf28DRqQb74KuDRAHaN44UYBxA1begy5gFOc7cEQTRu0
WACGM8jNL2eWWLXDNnQQTfb2t1v7LbbMorazyCn2e5ujamE4+DSaYWJF5axZiaQN
ZcRVATw0SPiQlsQW/G014SSFJT0waybxWLOynWS9MSgjx84/GRYWvxRv
=3ATM
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added
spi-mem code. The Tegra fix is relatively large but fairly
straightforward and mechanical, it runs on probe so it's been
reasonably well covered in -next testing."
* tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-mem: Move the DMA-able constraint doc to the kerneldoc header
spi: spi-mem: Add missing description for data.nbytes field
spi: rspi: Fix interrupted DMA transfers
spi: rspi: Fix invalid SPI use during system suspend
spi: sh-msiof: Fix handling of write value for SISTR register
spi: sh-msiof: Fix invalid SPI use during system suspend
spi: gpio: Fix copy-and-paste error
spi: tegra20-slink: explicitly enable/disable clock
The of_find_spi_device_by_node() helper function is useful for other
modules too. Export the funciton as GPL like all other spi helper
functions and make it available if CONFIG_OF is enabled, because it isn't
related to the CONFIG_OF_DYNAMIC context. Finally add a stub if
CONFIG_OF isn't enabled, so others must not care about it.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the appropriate SPDX license identifier and drop the previous
license text.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On r8a7791/koelsch:
m25p80 spi0.0: error -22 reading 9f
m25p80: probe of spi0.0 failed with error -22
Apparently the logic in spi_mem_check_op() is wrong, rejecting the
spi-mem operation if any buswidth is valid, instead of invalid.
Fixes: 380583227c ("spi: spi-mem: Add extra sanity checks on the op param")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The __exit section is left out for built-in drivers, so a
'remove' callback must not be marked as such to avoid breaking when
we unbind a device at runtime. This was pointed out by kbuild:
`sprd_spi_remove' referenced in section `.data' of drivers/spi/spi-sprd.o: defined in discarded section `.exit.text' of drivers/spi/spi-sprd.o
Fixes: e7d973a31c ("spi: sprd: Add SPI driver for Spreadtrum SC9860")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns when one enumerated type is converted implicitly to another:
drivers/spi/spi-pic32.c:323:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-pic32.c:333:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_TO_DEVICE,
^~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_transfer_direction (DMA_FROM_DEVICE =
DMA_DEV_TO_MEM = 2, DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1) to satify Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/159
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some combinations are simply not valid and should be rejected before
the op is passed to the SPI controller driver.
Add an spi_mem_check_op() helper and use it in spi_mem_exec_op() and
spi_mem_supports_op() to make sure the spi-mem operation is valid.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This remove the check and subsequent return of error for the case when
a SPI device requires SPI_CS_WORD and is also configured to use a GPIO
for the CS line.
Commit a134cc414e86 ("spi: always use software fallback for SPI_CS_WORD
when using cs_gio") handles this case now, so this check is no longer
necessary.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This modifies the condition for using the software fallback
implementation for SPI_CS_WORD when the SPI controller is using a GPIO
for the CS line. When using a GPIO for CS, the hardware implementation
won't work, so we just enable the software fallback globally in this
case.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mediatek SPI driver modifies some fields (tx_buf, rx_buf, len, tx_dma,
rx_dma) of the spi_transfer* passed in when doing transfer_one and in
interrupt handler. This is somewhat unexpected, and there are some
caller (e.g. Cr50 spi driver) that reuse the spi_transfer for multiple
messages. Add a field to record how many bytes have been transferred,
and calculate the right len / buffer based on it instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I23e218cd964f16c0b2b26127d4a5ca6529867673
Signed-off-by: Mark Brown <broonie@kernel.org>
If the pll clock needs to be enabled to get its rate, it will also need
to be enabled to provide it. So ensure it is kept enabled through the
lifetime of the device.
Fixes: 0d7412ed1f ("spi/bcm63xx-hspi: Enable the clock before calling clk_get_rate().")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It makes no sense to remove the device on shutdown. And it break things
when the hardware crucial for shutdown (such as the embedded controller)
is attached to the SPI bus.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the SPI_CS_WORD flag to the TI DaVinci SPI
driver. This mode can be used as long as we are using the hardware
chip select and not a GPIO chip select.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This provides a SPI operation mode which changes chip select after every
word, used by some devices such as ADCs and DACs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlugGWgTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0OAqB/99Zk/yjUqw3q8mQ9TcDyurMrllpNYm
n9KshwKOc1wyfHsbPMke+ytCJHmMpNDKbv80Dk5aTNBvbeNN9OZdcqonGfVfulEB
hhZy6X4wN6QwX6HpIeWl52o4V4zLd0skeZOqMod/4RQKQvG7kCVVetKFfzMBxYpP
4B+jVLg/L/lVsbNqXe53A59C0myg/lkCBFL9uWmiUaAScS/eeWmHX/Z+Guf3DTjo
eR0ZoB55HeovL8AsTV0xAwjae+YM6LMElptXLF/+AlaFmW4WmuRGuU2tCXh+SaHU
/VzwLgekzd1hplHc8tX1Nhdr4qJhI6tcpQOu+IelTqZ/Z/JlpIruaJVB
=sMBd
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlugGesTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LpbB/9eeBHjpAthphCZ1Q87oUtqn0dbhV9j
+djnjM3BgJX+3T3vl6fnOtyD2MPg/sGX8pMePEcVqUSRp+StY5tCO++zbR7maMxs
Czw5GslnJJ9CG6T7xx1ZE1vWAIeWywH7Pw98daFJpQkj17BEhGrrqSbpctJaRdSy
3e5nZvc3mWQ5k4ttmK+C9MTa6XV3ReaHDfJaagXWM7bykV6mDwVh6dyx4QJ7kwht
Ti+MQ+SYZndySXTFoborSss+5zgYIJ5nKr07PvOsNrjlk2p3hoU+y7MuU+RB9zzs
XP9dgZKSoLWbFdCspaC6DtcT1P2HLQRi5kBfdc8xlUCupa6Y2Jt3Hms1
=TFpo
-----END PGP SIGNATURE-----
Merge tag 'spi-cs-word' into spi-4.20
spi: Provide SPI_CS_WORD
This provides a SPI operation mode which changes chip select after every
word, used by some devices such as ADCs and DACs.
This adds a default software implementation for the SPI_CS_WORD flag for
controllers that don't have such a feature.
The SPI_CS_WORD flag indicates that the CS line should be toggled
between each word sent, not just between each transfer. The
implementation works by using existing functions to split transfers into
one-word-sized transfers and sets the cs_change bit for each of the
new transfers.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As well as one driver fix there's a couple of fixes here which address
issues with the use of IDRs for allocation of dynamic bus numbers,
ensuring that dynamic bus numbers interact well with static bus numbers
assigned via DT and otherwise.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluf2foTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DooB/4/c+c9nX31WeKh5EUFS3WJUQ4quHC+
ZPS0rqliJm0KQxdSCU6ig2+xbobZWAs9T4ZXPlE7PNk6DmqdtATS5jlzbwmoLvdA
PvxsBwz3dRdIGR/BNbDYEZCb0WGtMHO6BR5c//lBCy+ea5oNENi0w0mFnY+AVeUt
ivM55i/nNmV4DReT3rl5mRz/TQgfI9zc11DPpqDnlQML3emYHmJ+hZa8/1g68d8C
lQHLIQMo6hGyOd3p6uPODGt98cDKIuYl9+fcYVzYFScNshwuMsxTDUXpkhv85Frb
QV6LGlikaEQBh9X9BHjzTHMBqbTFVLX/I+jRC/vK2G21862rfOt3R6vh
=rRj7
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
As well as one driver fix there's a couple of fixes here which address
issues with the use of IDRs for allocation of dynamic bus numbers,
ensuring that dynamic bus numbers interact well with static bus numbers
assigned via DT and otherwise."
* tag 'spi-fix-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-fsl-dspi: fix broken DSPI_EOQ_MODE
spi: Fix double IDR allocation with DT aliases
spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers
Almost all spi drivers assign spi master->dev.of_node from
its parent platform device without additional refcounting.
It seems of_node_get() in pic32_sqi_probe() is unnecessary
and there is no corresponding of_node_put().
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-davinci.c: In function 'davinci_spi_setup':
drivers/spi/spi-davinci.c:422:36: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DaVinci SPI can use either:
- Internal chip selects (inside the SPI host)
- External chip selects (using GPIO)
- External chip selects passed in pdata
The last way of passing external chip selects through
platform data is not used in the kernel. Delete it to make
the code simpler when refactoring GPIO.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Michele Dionisio <michele.dionisio@gmail.com>
Cc: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need that to adjust the len of the 2nd transfer (called data in
spi-mem) if it's too long to fit in a SPI message or SPI transfer.
Fixes: c36ff266dc ("spi: Extend the core to ease integration of SPI memory controllers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for at91-usart in spi mode. The USART IP can be configured
to work in many modes and one of them is SPI.
The driver was tested on sama5d3-xplained and sama5d4-xplained boards with
enc28j60 ethernet controller as slave.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviwed-by: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a logical problem in spi-gpio with host just
assigning a MOSI line and no MISO: this is interpreted
as the host cannot do RX and the host is flagged with
SPI_MASTER_NO_RX.
This is wrong: since GPIO lines can switch direction,
in 3WIRE operation the host will simply reverse the
direction of the GPIO line and start reading from it,
there is even code for doing this in the driver, but
it went unnoticed because it was tested by using a
master with 4 wires but a device using just 3 wires.
Remove the offending flag.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Almost all spi drivers assign spi master->dev.of_node from
its parent platform device without additional refcounting.
It seems of_node_get() in pic32_spi_probe() is unnecessary
and there is no corresponding of_node_put().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-pl022.c: In function 'do_polling_transfer':
drivers/spi/spi-pl022.c:1493:20: warning:
variable 'chip' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-dw driver currently only supports 8 or 16 bits per word.
Since the hardware supports 4-16 bits per word, adapt the driver
to also support this.
Tested on socfpga cyclone5 with a 9-bit SPI display.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-gpio.c: In function 'spi_gpio_remove':
drivers/spi/spi-gpio.c:450:33: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When interrupted, wait_event_interruptible_timeout() returns
-ERESTARTSYS, and the SPI transfer in progress will fail, as expected:
m25p80 spi0.0: SPI transfer failed: -512
spi_master spi0: failed to transfer one message from queue
However, as the underlying DMA transfers may not have completed, all
subsequent SPI transfers may start to fail:
spi_master spi0: receive timeout
qspi_transfer_out_in() returned -110
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
Fix this by calling dmaengine_terminate_all() not only for timeouts, but
also for errors.
This can be reproduced on r8a7991/koelsch, using "hd /dev/mtd0" followed
by CTRL-C.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume,
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Based on a patch for sh-msiof by Gaku Inami.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch changes writing to the SISTR register according to the H/W
user's manual.
The TDREQ bit and RDREQ bits of SISTR are read-only, and must be written
their initial values of zero.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Cleanup, reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
spi_controller_{suspend,resume}() already prints an error message on
failure, so there is no need to repeat this in individual drivers.
Note: spi_master_{suspend,resume}() is an alias for
spi_controller_{suspend,resume}().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes an embarrassing copy-and-paste error in the
errorpath of spi_gpio_request(): we were checking the wrong
struct member for error code right after retrieveing the
sck GPIO.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change increases the source code readability.
Instead of using `spi->child[cs].direct_access.XXX` use `dir_acc->XXX`.
Instead of using `orion_spi->child[cs].direct_access.vaddr` use `vaddr`.
Signed-off-by: Kosta Zertsekel <zertsekel@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on the SPI instance one may get an interrupt storm upon
requesting resp. interrupt unless the clock is explicitly enabled
beforehand. This has been observed trying to bring up instance 4 on
T20.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Define a mask for the IF_SI_OWNER field.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-davinci.c: In function 'davinci_spi_chipselect':
drivers/spi/spi-davinci.c:211:36: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unfortunately, the Jaguar2 CPU_SYSTEM_CTRL register set has a different
layout than the Ocelot one. Handle that while keeping most of the code
common.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the SPI controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Lanqing Liu <lanqing.liu@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the dspi_eoq_write function used by the
ColdFire mcf5441x family. The 16 bit cmd part must be re-set at
each data transfer.
Also, now that fifo_size variables are used for eoq_read/write,
a proper fifo size must be set (16 slots for the ColdFire dspi
module version).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Acked-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI bus number is provided by a DT alias, idr_alloc() is called
twice, leading to:
WARNING: CPU: 1 PID: 1 at drivers/spi/spi.c:2179 spi_register_controller+0x11c/0x5d8
couldn't get idr
Fix this by moving the handling of fixed SPI bus numbers up, before the
DT handling code fills in ctlr->bus_num.
Fixes: 1a4327fbf4 ("spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
This introduces devres helpers and an API to request a lock by name,
then migrates the sprd SPI driver to use these.
-----BEGIN PGP SIGNATURE-----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=zanh
-----END PGP SIGNATURE-----
Merge tag 'hwlock-v4.19' of git://github.com/andersson/remoteproc
Pull hwspinlock updates from Bjorn Andersson:
"This introduces devres helpers and an API to request a lock by name,
then migrates the sprd SPI driver to use these"
* tag 'hwlock-v4.19' of git://github.com/andersson/remoteproc:
hwspinlock: Fix incorrect return pointers
spi: sprd: Change to use devm_hwspin_lock_request_specific()
spi: sprd: Replace of_hwspin_lock_get_id() with of_hwspin_lock_get_id_byname()
hwspinlock: Fix one comment mistake
hwspinlock: Remove redundant config
hwspinlock: Add devm_xxx() APIs to register/unregister one hwlock controller
hwspinlock: Add devm_xxx() APIs to request/free hwlock
hwspinlock: Add one new API to support getting a specific hwlock by the name
On systems where some controllers get a dynamic ID assigned and some have
a fixed number (e.g. from ACPI tables), the current implementation might
run into an IDR collision: in case of a fixed bus number is gotten by a
driver (but not marked busy in IDR tree) and a driver with dynamic bus
number gets the same ID and predictably fails.
Fix this by means of checking-in fixed IDsin IDR as far as dynamic ones
at the moment of the controller registration.
Fixes: 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
On non-OF systems spi->controlled_data may be NULL. This causes a NULL
pointer derefence on dm365-evm.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When porting (Q)SPI controller drivers from the MTD layer to the SPI
layer, the naming scheme for the memory devices changes. To be able
to keep compatibility with the old drivers naming scheme, a name
field is added to struct spi_mem and a hook is added to let controller
drivers set a custom name for the memory device.
Example for the FSL QSPI driver:
Name with the old driver: 21e0000.qspi,
or with multiple devices: 21e0000.qspi-0, 21e0000.qspi-1, ...
Name with the new driver without spi_mem_get_name: spi4.0
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit removed include headers of linux/of.h and linux/of_platform.h,
because they are not used.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SPI_3WIRE support to spi-gpio controller introducing
set_line_direction function pointer in spi_bitbang data structure.
Spi-gpio controller has been tested using hts221 temp/rh iio sensor
running in 3wire mode and lsm6dsm running in 4wire mode
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the capability to specify the flag parameter used in
bitbang_txrx_be_cpha{0,1} through the txrx_word function pointers of
spi_bitbang data structure. That feature will be used to add spi-3wire
support to the spi-gpio controller
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SPI controller driver implemented in Socionext UniPhier SoCs.
UniPhier SoCs have two types SPI controllers; SCSSI supports a
single channel, and MCSSI supports multiple channels.
This driver supports SCSSI only.
This controller has 32bit TX/RX FIFO with depth of eight entry,
and supports the SPI master mode only.
This commit is implemented in PIO transfer mode, not DMA transfer.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Even if the chip select line is not controlled by the SPFI
hardware, the device select bits need to be set to specify
the chip select line in use for the hardware to know what
parameters to use for the current transfer.
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable count, l, mcspi and spi_cntrl are being assigned but are
never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'count' set but not used [-Wunused-but-set-variable]
warning: variable 'l' set but not used [-Wunused-but-set-variable]
warning: variable 'mcspi' set but not used [-Wunused-but-set-variable]
warning: variable 'spi_cntrl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because the SPI controller deasserts the chip select when the TX fifo is
empty (which may happen in the middle of a transfer), the CS should be
handled by linux. Unfortunately, some or all of the first four chip
selects are not muxable as GPIOs, depending on the SoC.
There is a way to bitbang those pins by using the SPI boot controller so
use it to set the chip selects.
At init time, it is also necessary to give control of the SPI interface to
the Designware IP.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Export dw_spi_set_cs so it can be used from the various IP integration
modules.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Log RX and TX fifo counters when a transfer is done and these are not
zero.
Signed-off-by: Tiago Brusamarello <tiago.brusamarello@datacom.ind.br>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dynamic burst mode allows to group together multiple words and send them
in one continuous burst. When the number of bytes to be sent is not a
strict multiple of the FIFO entry size (32 bits), the controller expects
the non aligned bits to be sent first.
This commit adds support for this particular constraint, avoiding the
need to send the non-aligned bytes one by one at the end of the
transfer, speeding-up transfer speed in that case.
With this method, a transfer is divided into multiple bursts, limited in
size by the maximum amount of data that the controller can transfer in
one continuous burst (which is 512 bytes).
The non-512 byte part of the transfer is sent first. The remaining bytes
to be transferred in the current burst is stored in the 'remainder'
field.
With this method, the read_u32 field is no longer necessary, and is
removed.
This was tested on imx6 solo and imx6 quad.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_imx_can_dma function computes the watermark level so that
the transfer will fit in exactly N bursts (without a remainder).
The smallest watermark level possible being one FIFO entry per burst, we
can't never have a case where the transfer size isn't divsiible by 1.
Remove the extra check for the wml being different than 0.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core enforces that we always use the next power-of-two number of
bytes to store words. As a result, a 24 bits word will be stored in 4
bytes.
This commit fixes the spi_imx_bytes_per_word function to return the
correct number of bytes.
This also allows to get rid of unnecessary checks in the can_dma
function, since the SPI core validates that we always have a transfer
length that is a multiple of the number of bytes per word.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dynamic bursts mode allows to group together multiple words into a
single burst. To do so, it's necessary that words can be packed into the
32-bits FIFO entries, so we can't allow using this mode with bit_per_words
different to 8, 16 or 32.
This prevents shitfing out extra clock ticks for transfers with
bit_per_word values not aligned on 8 bits.
With that , we are sure that only the correct number of bits is
shifted out at each transfer, so we don't need to mask out the remaining
parts of the words.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some fields in struct spi_imx_data are assigned a different value twice
in a row, in spi_imx_setupxfer.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltPMSETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BizB/9lSfg4JrgJdAP8mDWfi7L5LjbpP9bB
9n1MlUFGRGU0Uc/yOD99QA6kB1WSpthFcgLBj+JDn3X30MzOqfZcHb3d9x5Z+XiV
YnIPzYqBPnnMSeTAX21c3Tz5nwO9hgz/xYr8onwYPeJWmt4RltYhiMdCgCQFWm9c
QaYNHiHymJP0ZFPXzLXlnIf+OW21ZOO9bH+eX1PAzbuWoDPxJZ63Eir22eKwTNey
bIIu19sxZE6o6Rd2Z0XAPtSGbd/r/9ULZAQcP429H+ETIfyefC6/IZv+yd4NrHmc
7WpWYi0JNdPLCXgLOvg5mwPBgDfs3tzoInWQu305882qlaK6kkivCgBu
=JPLR
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltPMZgTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JxACACAVtjwSy7KjJZ92ZljiyDP2MUydcM8
+6WiN96NCQVgMwFb6WBfePSJFeDeAnr0t4oANZpfa9rGV7YEYB5KlPmkGvuP+u6N
Jj+kRYXNcsu4LiyfZ82b/in3nBQ370Ufe32c4OECD/WDBLUx9TfWcur0sHLjHyp0
wh/9VxqQcGjgt/espt3QGDrASdymWHwF3sTEAoAIOeUzOgO61J2/4fQotUhPVPTN
q7jS6tmbR9GapEKGPOEzRz+3Ici3zK75zM3Yk2wSfh2xXk9Ly9q2HVO7ju7tC8Pe
XMnPxermqar/+PRgYYgLxrUDNyKHlzce4+hqc1cwj0XwAlvMiImB2nsB
=3WLv
-----END PGP SIGNATURE-----
Merge tag 'spi-dw-set-cs' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-4.19
spi: dw: Allow custom set_cs_callback
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is possible to get an interrupt as soon as it is requested. dw_spi_irq
does spi_controller_get_devdata(master) and expects it to be different than
NULL. However, spi_controller_set_devdata() is called after request_irq(),
resulting in the following crash:
CPU 0 Unable to handle kernel paging request at virtual address 00000030, epc == 8058e09c, ra == 8018ff90
[...]
Call Trace:
[<8058e09c>] dw_spi_irq+0x8/0x64
[<8018ff90>] __handle_irq_event_percpu+0x70/0x1d4
[<80190128>] handle_irq_event_percpu+0x34/0x8c
[<801901c4>] handle_irq_event+0x44/0x80
[<801951a8>] handle_level_irq+0xdc/0x194
[<8018f580>] generic_handle_irq+0x38/0x50
[<804c6924>] ocelot_irq_handler+0x104/0x1c0
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Upper layer users of SPI device drivers may rely on 'actual_length',
so it is important that information is correctly reported. One such
example is spi_mem_exec_op() function that will fail if
'actual_length' of the data transferred is not what was requested. Add
necessary code to populate 'actual_length.
Cc: Mark Brown <broonie@kernel.org>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: cphealy@gmail.com
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the missing clk_disable_unprepare() before return
from cnds_runtime_resume() in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Registers of DSPI should not be accessed before enabling its clock. On
Toradex Colibri VF50 on Iris carrier board this could be seen during
bootup as imprecise abort:
Unhandled fault: imprecise external abort (0x1c06) at 0x00000000
Internal error: : 1c06 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.39-dirty #97
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
Backtrace:
[<804166a8>] (regmap_write) from [<80466b5c>] (dspi_probe+0x1f0/0x8dc)
[<8046696c>] (dspi_probe) from [<8040107c>] (platform_drv_probe+0x54/0xb8)
[<80401028>] (platform_drv_probe) from [<803ff53c>] (driver_probe_device+0x280/0x2f8)
[<803ff2bc>] (driver_probe_device) from [<803ff674>] (__driver_attach+0xc0/0xc4)
[<803ff5b4>] (__driver_attach) from [<803fd818>] (bus_for_each_dev+0x70/0xa4)
[<803fd7a8>] (bus_for_each_dev) from [<803fee74>] (driver_attach+0x24/0x28)
[<803fee50>] (driver_attach) from [<803fe980>] (bus_add_driver+0x1a0/0x218)
[<803fe7e0>] (bus_add_driver) from [<803fffe8>] (driver_register+0x80/0x100)
[<803fff68>] (driver_register) from [<80400fdc>] (__platform_driver_register+0x48/0x50)
[<80400f94>] (__platform_driver_register) from [<8091cf7c>] (fsl_dspi_driver_init+0x1c/0x20)
[<8091cf60>] (fsl_dspi_driver_init) from [<8010195c>] (do_one_initcall+0x4c/0x174)
[<80101910>] (do_one_initcall) from [<80900e8c>] (kernel_init_freeable+0x144/0x1d8)
[<80900d48>] (kernel_init_freeable) from [<805ff6a8>] (kernel_init+0x10/0x114)
[<805ff698>] (kernel_init) from [<80107be8>] (ret_from_fork+0x14/0x2c)
Cc: <stable@vger.kernel.org>
Fixes: 5ee67b587a ("spi: dspi: clear SPI_SR before enable interrupt")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Ice Lake SPI host controller follows the Intel Cannon Lake but the
PCI IDs are different. Add the new PCI IDs to the driver supported
devices list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Change to use devm_hwspin_lock_request_specific() instead of
freeing the hwlock explicitly when unbound the device.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now the hwlock core has supplied new function to get a specific hwlock id
by one hwlock name, which is more clear for users. So change to use
of_hwspin_lock_get_id_byname().
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It seems that the proper structure field to use in this particular
case is *regmap_pushr* instead of regmap.
Addresses-Coverity-ID: 1470126 ("Copy-paste error")
Fixes: 58ba07ec79 ("spi: spi-fsl-dspi: Add support for XSPI mode registers")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Esben Haabendal <eha@deif.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the XSPI bit for devices configured for XSPI mode (currently LS1021A),
and thereby switch to extended SPI mode, allowing for SPI transfers using
from 4 to 32 bits per word instead of 4 to 16 bits per word.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This implements handling of split CMD and TX FIFO queues for XSPI when
running in TCFQ mode.
It should be simple to add it to EOQ mode also. Currently, EOQ mode is
only used with coldfire. So if coldfire DSPI supports XSPI, XSPI FIFO
handling should be added to EOQ mode also.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This prepares for adding support for extended SPI mode (XSPI), by extending
the regmap with the extra SREX and CTAREx registers.
An additional register map is made for allowing 16 bit access to CMD and TX
FIFO of the PUSHR register separately, which is also needed for XSPI mode
support.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark volatile registers to avoid caching bugs.
Note: SPI_MCR is marked volatile because of CLR_TXF and CLR_RXF bits.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MCR register is not changed, so initialize it in dspi_init().
The exception is the CLR_TXF and CLR_RXF bits, which should be written to
before each transfer to make sure we start with empty FIFOs. With MCR
register now configured as volatile, the regmap_update_bits will do a real
read-modify-write cycle.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This extends the driver with support for all SPI framesizes from 4 to 16
bits, and adds support for per transfer specific bits_per_word, while at
the same time reducing code size and complexity.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify driver by avoiding counter wrapping by clearing transfer counter
on first SPI transfer per interrupt instead of tracking what it was before.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As of 92dc20d83a, transfer->cs_change has
been supported for non-last transfers, but not for last transfer.
This change brings handling of cs_change in line with the specification in
spi.h, implementing handling of transfer->cs_change for all transfers.
The value for CMD FIFO is precalculated with transfer->cs_change field
taken into account, allowing for CS de-activate between transfers and
keeping CS activated after last transfer.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Checking directly against pointer value should be at least as fast as doing
bitmasking and compare, so let's keep it simple.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The if statement just above this if/else statement triggers on the same
condition, and then invalidates it.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code did not de-assert any CS GPIOs before probing slaves. This
means that several CS signals could be active at once, garbling the
communication. Whether this was actually a problem depended on the type
of the SPI device attached (so my "spidev" for userspace access worked
correctly because its probe was effectively a no-op), and on the state
of the GPIO pins at SoC's boot.
The code was already iterating through all DT children of the SPI
controller, so this change re-uses that loop for CS GPIO setup as well.
This means that this might change the number of the HW CS signal which
is picked for all GPIO CS devices. Previously, the lowest one was used,
but we now use the first one from the DT.
With this move of the code, we can also finally initialize each GPIO CS
lane before registering the SPI controller (which in turn probes for
slaves).
I tried to fix this in 544248623b already, but that only did it half
way by registering the GPIOs properly. That patch failed to set their
logic signals early enough, though.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
The path "spi: cadence: Add usleep_range() for
cdns_spi_fill_tx_fifo()" added a usleep_range() function call,
which cannot be used in atomic context.
However the cdns_spi_fill_tx_fifo() function can be called during
an interrupt which may result in a kernel panic:
BUG: scheduling while atomic: grep/561/0x00010002
Modules linked in:
Preemption disabled at:
[<ffffff800858ea28>] wait_for_common+0x48/0x178
CPU: 0 PID: 561 Comm: grep Not tainted 4.17.0 #1
Hardware name: Cadence CSP (DT)
Call trace:
dump_backtrace+0x0/0x198
show_stack+0x14/0x20
dump_stack+0x8c/0xac
__schedule_bug+0x6c/0xb8
__schedule+0x570/0x5d8
schedule+0x34/0x98
schedule_hrtimeout_range_clock+0x98/0x110
schedule_hrtimeout_range+0x10/0x18
usleep_range+0x64/0x98
cdns_spi_fill_tx_fifo+0x70/0xb0
cdns_spi_irq+0xd0/0xe0
__handle_irq_event_percpu+0x9c/0x128
handle_irq_event_percpu+0x34/0x88
handle_irq_event+0x48/0x78
handle_fasteoi_irq+0xbc/0x1b0
generic_handle_irq+0x24/0x38
__handle_domain_irq+0x84/0xf8
gic_handle_irq+0xc4/0x180
This patch replaces the function call with udelay() which can be
used in an atomic context, like an interrupt.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In case of a bi-directional transfer, receive DMA may complete in the
rcar-dmac driver before transmit DMA, due to scheduling latencies.
As the MSIOF driver waits for completion of the receive DMA only, it may
submit the next transmit DMA request before the previous one has
completed.
Make the driver more robust by waiting for the completion of both
receive and transmit DMA, when applicable.
Based on a patch in the BSP by Ryo Kataoka.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
These include a significant update of the generic power domains (genpd)
and Operating Performance Points (OPP) frameworks, mostly related to
the introduction of power domain performance levels, cpufreq updates
(new driver for Qualcomm Kryo processors, updates of the existing
drivers, some core fixes, schedutil governor improvements), PCI power
management fixes, ACPI workaround for EC-based wakeup events handling
on resume from suspend-to-idle, and major updates of the turbostat
and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks
in the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the
schedutil cpufreq governor (Joel Fernandes, Dietmar Eggemann,
Rafael Wysocki, Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman,
Viresh Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag
set and update stale comments in the PCI core PM code (Rafael
Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver
(David Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wqBV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
* pm-domains:
PM / domains: Improve wording of dev_pm_domain_attach() comment
PM / Domains: Don't return -EEXIST at attach when PM domain exists
spi: Respect all error codes from dev_pm_domain_attach()
soundwire: Respect all error codes from dev_pm_domain_attach()
mmc: sdio: Respect all error codes from dev_pm_domain_attach()
i2c: Respect all error codes from dev_pm_domain_attach()
driver core: Respect all error codes from dev_pm_domain_attach()
amba: Respect all error codes from dev_pm_domain_attach()
PM / Domains: Allow a better error handling of dev_pm_domain_attach()
PM / Domains: Check for existing PM domain in dev_pm_domain_attach()
PM / Domains: Drop redundant code in genpd while attaching devices
PM / Domains: Drop comment in genpd about legacy Samsung DT binding
PM / Domains: Fix error path during attach in genpd
The correct form is "a high-level", so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to section 59.2.4 MSIOF Receive Mode Register 1 (SIRMDR1) in
the R-Car Gen3 datasheet Rev.1.00, the value of the SIRMDR1.SYNCAC bit
must match the value of the SITMDR1.SYNCAC bit. However,
sh_msiof_spi_setup() changes only the latter.
Fix this by updating the SIRMDR1 register like the SITMDR1 register,
taking into account register bits that exist in SITMDR1 only.
Reported-by: Renesas BSP team via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 7ff0b53c40 ("spi: sh-msiof: Avoid writing to registers from spi_master.setup()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5a686b2c9e ("spi: omap2-mcspi: Idle hardware during suspend
and resume") added calls for pm_runtime_force_suspend() and
pm_runtime_force_resume() to make sure spi is idled between
device_prepare() and device_complete().
But testing Linux next, I now noticed that we will get the following:
spi_master spi0: Failed to power device: -13
Looking at things more turns out we can just remove this non-standard
code. I was probably testing with some extra experimental patches
earlier when I thought we need pm_runtime_force_suspend() and
pm_runtime_force_resume().
Fixes: 5a686b2c9e ("spi: omap2-mcspi: Idle hardware during suspend
and resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If pm_runtime_get_sync() fails we should call pm_runtime_put_noidle().
This is probably not a critical fix as we should only hit this when
things are broken elsewhere.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
resource_size() is dereferencing the res without checking that it is
not NULL, so we need to do the check before calling resource_size().
Fixes: b95cb394ab ("spi: ti-qspi: Implement the spi_mem interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since Linux v4.10 release (commit 1d9174fbc5 "PM / Runtime: Defer
resuming of the device in pm_runtime_force_resume()"),
pm_runtime_force_resume() function doesn't runtime resume device if it was
not runtime active before system suspend. Thus, driver should not do any
register access after pm_runtime_force_resume() without checking the
runtime status of the device. To fix this issue, simply move
s3c64xx_spi_hwinit() call to s3c64xx_spi_runtime_resume() to ensure that
hardware is always properly initialized. This fixes Synchronous external
abort issue on system suspend/resume cycle on newer Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The limitation of being able to check only for -EPROBE_DEFER from
dev_pm_domain_attach() has been removed. Hence let's respect all error
codes and bail out accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Patch http://patchwork.ozlabs.org/patch/905205/ has been partially
applied, and changes to the bcm-qspi driver have been lost somehow
(probably due to a conflict when applying the patch).
Remove the ->spi_flash_read() bits from this driver to fix the build
error.
Fixes: c1f5ba70de ("spi: Get rid of the spi_flash_read() API")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This API has been replaced by the spi_mem_xx() one, its only user
(spi-nor) has been converted to spi_mem_xx() and all SPI controller
drivers that were implementing the ->spi_flash_xxx() hooks are also
implementing the spi_mem ones. So we can safely get rid of this API.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_mem interface is meant to replace the spi_flash_read() one.
Implement the ->exec_op() method so that we can smoothly get rid of the
old interface.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_mem interface is meant to replace the ->spi_flash_read() one.
Implement the ->exec_op() method to ease removal of the old interface.
Not that ->spi_flash_read() is now implemented as a wrapper around the
new bcm_qspi_exec_mem_op() function so that we can easily get rid of
it when ->spi_flash_read() is removed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Tested-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI/QuadSPI controllers only expose a high-level SPI memory
interface, thus preventing any regular SPI transfers from being done.
In that case, SPI controller drivers can leave all ->transfer_xxx()
hooks empty and only implement the spi_mem_ops interface.
Adjust the core to allow such situations:
- extend spi_controller_check_ops() to accept situations where all
->transfer_xxx() pointers are NULL only if ->mem_ops != NULL
- make sure we do not initialize the SPI message queue if
ctlr->transfer_one and ctlr->transfer_one_message are missing
- return -ENOTSUPP if someone tries to do a regular SPI transfer on
a controller that does not support it
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controllers are exposing high-level interfaces to access various
kind of SPI memories. Unfortunately they do not fit in the current
spi_controller model and usually have drivers placed in
drivers/mtd/spi-nor which are only supporting SPI NORs and not SPI
memories in general.
This is an attempt at defining a SPI memory interface which works for
all kinds of SPI memories (NORs, NANDs, SRAMs).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
I accidentally sent an early version of patch removing spi-bcm53xx
driver which got rid of .c and .h files *only*. I amended local commit
but forgot to re-format the patch.
This commit removes leftovers of dropped driver.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver was added by commit 0fc6a323e1 ("spi: bcm53xx: driver for
SPI controller on Broadcom bcma SoC") back in 2014. It was needed to
provide a minimal support for SPI controller on BCM5301X (AKA Northstar)
devices.
An alternative driver was added by Kamal in commit fa236a7ef2 ("spi:
bcm-qspi: Add Broadcom MSPI driver") 2 years later. It supports the same
hardware but for some reason a new driver has been developed for it.
At this point the new driver supports: more modes, setting a speed,
setting bits per word and uses IRQs instead of polling. DTS file for
BCM5301X has also been updated in the commit 1c8f406507 ("ARM: dts:
BCM5301X: convert to iProc QSPI") - over a year ago.
That explained I see no reason to keep the old driver alive.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() can fail, so its return value should be checked and
acted upon.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3343b7a6d2 ("spi/pxa2xx: convert to the common clk framework")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 AUX SPI has a shared interrupt line (with AUX UART).
Downstream fixes this with an AUX irqchip to demux the IRQ sources and a
DT change which breaks compatibility with older kernels. The AUX irqchip
was already rejected for upstream[1] and the DT change would break
working systems if the DTB is updated to a newer one. The latter issue
was brought to my attention by Alex Graf.
The root cause however is a bug in the shared handler. Shared handlers
must check that interrupts are actually enabled before servicing the
interrupt. Add a check that the TXEMPTY or IDLE interrupts are enabled.
[1] https://patchwork.kernel.org/patch/9781221/
Cc: Alexander Graf <agraf@suse.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-spi@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently are calling mcspi suspend and resume without considering
that mcspi might provide resources for other device driver such as
regulators. This means resume can fail and will produce -EACCES if
errors if anything calls mcspi functions between device_prepare()
and device_complete().
To fix the issue, let's do the following changes:
1. Let's add checking for return values for pm_runtime_get calls,
and call pm_runtime_put_noidle() on errors. Things still fail
after this change, but at least we see something is wrong as
we now see -EACCES errors on resume.
2. Let's use noirq level for suspend and resume as other drivers
can still call SPI related functions on suspend and resume. This
still won't fix the -EACCES issue, but gets us to something a bit
saner.
3. Finally, let's modify suspend and resume to call to make sure
the device is idled properly on suspend. We have device_prepare()
call pm_runtime_get_noresume() that won't get released until in
device_complete() when it calls pm_runtime_put(). So if SPI is
still active on entering suspend, it will never get idled unless
we add calls to pm_runtime_force_suspend() and resume. This also
fixes the -EACCES errors on resume together with changes 1 and 2
above.
And since we're already rewriting suspend resume functions, let's
arrange the order of suspend and resume functions to be like they
usually are with suspend first.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can have the SoC enter off mode also during idle, not just
during suspend. Currently we are handling the CS restore properly
for unused CS only for resume and not for runtime resume.
Let's just move all the context related restore to runtime_resume().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If devm_spi_register_master() fails in meson_spicc_probe(),
spicc->core is left undisabled. The patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Always confirm the BSPI_MAST_N_BOOT_CTRL bit when enabling
or disabling BSPI transfers.
Fixes: 4e3b2d236f ("spi: bcm-qspi: Add BSPI spi-nor flash controller driver")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Added fix for probing of spi-nor device non-zero chip selects. Set
MSPI_CDRAM_PCS (peripheral chip select) with spi master for MSPI
controller and not for MSPI/BSPI spi-nor master controller. Ensure
setting of cs bit in chip select register on chip select change.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Replace the manual validity checks for the GPIO with the
gpio_is_valid().
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Right now, no checks are done on the presence of a ->transfer[_xxx]()
method, which can lead to a NULL pointer dereference when someone
starts sending something on the bus.
Do the check at registration time and refuse to add the controller if
all ->transfer[_xxx]() pointers are NULL.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable the clock prior to calling clk_get_rate(), because clk_get_rate()
should only be called if the clock is enabled.
Additionally, prepare/enable the pll_clk before calling clk_get_rate()
for the same reason.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 142168eba9 ("spi: bcm63xx-hsspi: add bcm63xx HSSPI driver")
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the 32-bit device address only is supported for DMA. However,
starting from Intel Sunrisepoint PCH the DMA address of the device FIFO
can be 64-bit.
Change the respective variable to be compatible with DMA engine
expectations, i.e. to phys_addr_t.
Fixes: 34cadd9c1b ("spi: pxa2xx: Add support for Intel Sunrisepoint")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This is needed by the spi-mem logic to force all messages that have been
queued before a memory operation to be sent before we start the memory
operation. We do that in order to guarantee that spi-mem operations do
not preempt regular SPI transfers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_{map,unmap}_buf() are needed by the spi-mem logic that is about to
be introduced to prepare data buffer for DMA operations.
Remove the static specifier on these functions and add their prototypes
to drivers/spi/internals.h. We do not export the symbols here because
both SPI_MEM and SPI can't be enabled as modules and we'd like to
prevent controller/device drivers from using these functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the 32-bit device address only is supported for DMA. However,
starting from Intel Sunrisepoint PCH the DMA address of the device FIFO
can be 64-bit.
Change the respective variable to be compatible with DMA engine
expectations, i.e. to phys_addr_t.
Fixes: 34cadd9c1b ("spi: pxa2xx: Add support for Intel Sunrisepoint")
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some variants of the SPI controller have no DMA support, in such case
SPI transfers longer than the FIFO length are not currently properly
handled by the driver. Fix it by doing multiple transfers in the
s3c64xx_spi_transfer_one() function if the SPI transfer length exceeds
the FIFO size.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
More references to fifo_len are added in subsequent patch.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a s3c64xx_ prefix to remaining generic function names so it is clear
the code is part of the driver when grepping or looking at debug logs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi pointer argument is not used now so remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of xspi work in busy condition, may send bytes failed.
once something wrong, spi controller did't work any more
My test found this situation appear in both of read/write process.
so when TX FIFO is full, add one byte delay before send data;
Signed-off-by: sxauwsk <sxauwsk@163.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the pump_transfers() transfer tasklet to transfer_one() hook the
SPI core calls to process single transfer instead of handling message
processing and chip select handling in the driver. This not only
simplifies the driver but also brings transfer statistics from the core.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are going to rename and modify pump_transfers(). Prepare for it by
removing the string "pump_transfers:" from error and warning prints.
While at it make these user-visible strings single line in sources as it
helps source grepping from error reports.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DMA engine implementation of pxa2xx_spi_dma_prepare() don't use
the dma_burst argument. Remove it since it became unused after
commit 6356437e65 ("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change indentation so register address offset and register bit definitions
are aligned to same column.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently timeout errors in polling I/O mode transfer are silently ignored.
Fix it by returning an error when we time out waiting on the RX FIFO level
to reach the transfer length.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The channel argument is not used and anyway it could be retrieved from
the passed driver data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The tgl_spi pointer is now unused so remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The change updates sh_msiof_spi_set_clk_regs() function by iterating
over BRDV power values. Note that the change is a functional one, namely
prescaler output x 1/1 set in BRDV bit field (0b111) for MSO division
rate set to 2 is substituted by BRDV = 0b000 and BRPS = 0b0, in terms
of written values to TSCR setting of 0x0107 is substituted by 0x0000,
and for all input parameter cases this is the only functional change,
which touches the controller.
As a result of the rework the function is supposed to be slightly more
efficient and more readable and maintainable in case of any further
extensions.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_get_rate() is below clk_prepare_enable(), so
its error should lead to goto err_clk_disable, not to err_master_put.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The change fixes a bit field overflow which allows to write to higher
bits while calculating SPI transfer clock and setting BRPS and BRDV
bit fields, the problem is reproduced if 'parent_rate' to 'spi_hz'
ratio is greater than 1024, for instance
p->min_div = 2,
MSO rate = 33333333,
SPI device rate = 10000
results in
k = 5, i.e. BRDV = 0b100 or 1/32 prescaler output,
BRPS = 105,
TSCR value = 0x6804, thus MSSEL and MSIMM bit fields are non-zero.
Fixes: 65d5665bb2 ("spi: sh-msiof: Update calculation of frequency dividing")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now i.MX SPI controller can work in Slave mode.
Update MODULE_DESCRIPTION to "SPI Controller driver".
Signed-off-by: wangbo <wang.bo116@zte.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
A quiet release for SPI, some fixes and small updates for individual
drivers with one bigger change from Linus Walleij which coverts the
bitbanging SPI driver to use the GPIO descriptor API from Linus Walleij.
Since GPIO descriptors were used by platform data this means there's a
few changes in arch/ making relevant updates for a few platforms and one
misc driver that are affected.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlrCYDYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DXhB/9Hueo2D1Pku0iAwq+yIAPvk2N0fyGP
YWJWbDQGngSZEnU3dUzdfaOHh4MMiMgs0q8hxOYnmkIhhTs7cXsPj8x6rlZP8bee
TtSEEgHSuHlVWyADquFIel8OCq8BWd7p4aQKqP3LaojCH/wqswxtn4I+RH/xw1Rd
LIPgU12fxGUpRMO7uGNiMhqqkQDH1ZBFzCUYRPqQk2E+5hyZraQYoROgZkEBPzb1
EWjLxLxytj/Zj4N5eQkW4BWfX5HKJb9CpwKIIdyNuybr14yC5FR83VxOf9wW4/pG
39DIn8LtGTkuMRF4Yw5rPlC9KqnLpUDTnQCcOW4lt+z8QtZQ+LP3boxE
=xNln
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull SPI updates from Mark Brown:
"A quiet release for SPI, some fixes and small updates for individual
drivers with one bigger change from Linus Walleij which coverts the
bitbanging SPI driver to use the GPIO descriptor API from Linus
Walleij.
Since GPIO descriptors were used by platform data this means there's a
few changes in arch/ making relevant updates for a few platforms and
one misc driver that are affected"
* tag 'spi-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (24 commits)
MAINTAINERS: update Andi's e-mail
spi: spi-atmel: Use correct enum for DMA transfer direction
spi: sh-msiof: Document R-Car M3-N support
spi: sh-msiof: Use correct enum for DMA transfer direction
spi: sprd: Add the support of restarting the system
spi: sprd: Simplify the transfer function
spi: Fix unregistration of controller with fixed SPI bus number
spi: rspi: use correct enum for DMA transfer direction
spi: jcore: disable ref_clk after getting its rate
spi: bcm-qspi: fIX some error handling paths
spi: pxa2xx: Disable runtime PM if controller registration fails
spi: tegra20-slink: use true and false for boolean values
spi: Fix scatterlist elements size in spi_map_buf
spi: atmel: init FIFOs before spi enable
spi: orion: Prepare space for per-child options
spi: orion: Make the error message greppable
spi: orion: Rework GPIO CS handling
spi: bcm2835aux: Avoid 64-bit arithmetic in xfer len calc
spi: spi-gpio: Augment device tree bindings
spi: spi-gpio: Rewrite to use GPIO descriptors
...
Use enum dma_transfer_direction as required by the functions
dmaengine_prep_slave_(sg|single)() instead of enum dma_data_direction.
This won't change behavior in practice as the enum values are
equivalent.
This fixes two warnings when building with clang:
drivers/spi/spi-atmel.c:771:12: warning: implicit conversion from enumeration
type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction'
[-Wenum-conversion]
DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
...
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The blackfin architecture is getting removed, so these
won't be needed any more.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use enum dma_transfer_direction as required by dmaengine_prep_slave_sg()
instead of enum dma_data_direction. This won't change behavior in
practice as the enum values are equivalent.
This fixes two warnings when building with clang:
drivers/spi/spi-sh-msiof.c:755:27: warning: implicit conversion from enumeration
type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
rx->sgl, rx->nents, DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-sh-msiof.c:772:27: warning: implicit conversion from enumeration
type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
tx->sgl, tx->nents, DMA_TO_DEVICE,
^~~~~~~~~~~~~
Based on commit 768d59f5d0 ("spi: rspi: use correct enum for DMA
transfer direction").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Spreadtrum platform, we use one PMIC watchdog to reset the whole system
with loading one suitable timeout value (usually 50ms) for the watchdog.
In theory, we should implement the restart function in drivers/power/reset
subsystem to access the PMIC watchdog with regmap. When restart the system,
other cores will be stopped by IPI, but if other cores were accessing PMIC
with holding the regmap mutex lock, that will cause dead-lock issue if we
try to access the PMIC watchdog with regmap to restart the whole system.
Thus we can implement the restart function in ADI driver to avoid this
issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can move the hardware spinlock protection into the ADI read/write
functions to simplify the sprd_adi_transfer_one() function. Moreover
this optimization can also help to access PMIC without considering
the hardware spinlock using sprd_adi_read/write() functions.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
ceased to unregister SPI buses with fixed bus numbers. Moreover this is
visible only if CONFIG_SPI_DEBUG=y is set or when trying to re-register
the same SPI controller.
rmmod spi_pxa2xx_platform (with CONFIG_SPI_DEBUG=y):
[ 26.788362] spi_master spi1: attempting to delete unregistered controller [spi1]
modprobe spi_pxa2xx_platform:
[ 37.883137] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:19.0/pxa2xx-spi.12/spi_master/spi1'
[ 37.894984] CPU: 1 PID: 1467 Comm: modprobe Not tainted 4.16.0-rc4+ #21
[ 37.902384] Call Trace:
...
[ 38.122680] kobject_add_internal failed for spi1 with -EEXIST, don't try to register things with the same name in the same directory.
[ 38.136154] WARNING: CPU: 1 PID: 1467 at lib/kobject.c:238 kobject_add_internal+0x2a5/0x2f0
...
[ 38.513817] pxa2xx-spi pxa2xx-spi.12: problem registering spi master
[ 38.521036] pxa2xx-spi: probe of pxa2xx-spi.12 failed with error -17
Fix this by not returning immediately from spi_unregister_controller() if
idr_find() doesn't find controller with given ID/bus number. It finds
only those controllers that were registered with dynamic SPI bus
numbers. Only conditional cleanup between dynamic and fixed bus numbers
is to remove allocated IDR.
Fixes: 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
Cc: stable@vger.kernel.org
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use enum dma_transfer_direction as required by dmaengine_prep_slave_sg
instead of enum dma_data_direction. This won't change behavior in
practice as the enum values are equivalent.
This fixes two warnings when building with clang:
drivers/spi/spi-rspi.c:538:26: warning: implicit conversion from enumeration
type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
rx->sgl, rx->nents, DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-rspi.c:558:26: warning: implicit conversion from enumeration
type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
tx->sgl, tx->nents, DMA_TO_DEVICE,
^~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver does not disable ref_clk on remove.
According to the comment, the only reason to enable the clock is to get
its rate. So, it should be safe to disable clk just after that.
By the way, clk_prepare_enable() looks to be more appropriate
than clk_enable() here.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason, commit c0368e4db4 ("spi: bcm-qspi: Fix use after free
in bcm_qspi_probe() in error path") has updated some gotos, but not all of
them.
This looks spurious, so fix it.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't leave runtime PM enabled in case devm_spi_register_controller()
returns with an error. Otherwise runtime PM will complain when driver is
reloaded:
[ 693.855811] pxa2xx-spi pxa2xx-spi.13: Unbalanced pm_runtime_enable!
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When SPI transfers can be offloaded using DMA, the SPI core need to
build a scatterlist to make sure that the buffer to be transferred is
dma-able.
This patch fixes the scatterlist entry size computation in the case
where the maximum acceptable scatterlist entry supported by the DMA
controller is less than PAGE_SIZE, when the buffer is vmalloced.
For each entry, the actual size is given by the minimum between the
desc_len (which is the max buffer size supported by the DMA controller)
and the remaining buffer length until we cross a page boundary.
Fixes: 65598c13fd ("spi: Fix per-page mapping of unaligned vmalloc-ed buffer")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The datasheet recommends initializing FIFOs before
SPI enable. If we do not do it like this, there may be
a strange behavior. We noticed that DMA does not work properly
with FIFOs if we do not clear them beforehand or enable them
before SPIEN.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Aggregating all options for a particular child underneath a common
struct looks cleaner compared to having a separate array for each
per-child option.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 544248623b introduced a new user-visible string which was
however split into two chunks. Thanks to Mark Brown for noticing.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Claim the GPIO from the driver, not via DT bindings or through the
platform code
- Find an unused HW CS signal because Orion needs to drive one for each
SPI transaction
The spi-orion.c was the only driver which supported (or cared about) the
CS GPIO, while it wasn't actually requesting it. This change means that
the DT bindings should stop hogging the GPIO CS pins because it's now
being handled by the driver.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
We want to check for xfers that are over 30 microseconds. Rather than
find how many µs a xfer will take, instead find how many bytes can be
transferred in 30 µs. The latter must be less than 32 bits (since our
clock speed is limited to 32 bits), while the former involves 64 bit
quantities and more arithmetic operations.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the bit-banged GPIO SPI driver to looking up and
using GPIO descriptors to get a handle on GPIO lines for SCK,
MOSI, MISO and all CS lines.
All existing board files are converted in one go to keep it all
consistent. With these conversions I rarely find any interrim
steps that makes any sense.
Device tree probing and GPIO handling should work like before
also after this patch.
For board files, we stop using controller data to pass the GPIO
line for chip select, instead we pass this as a GPIO descriptor
lookup like everything else.
In some s3c24xx machines the names of the SPI devices were set to
"spi-gpio" rather than "spi_gpio" which can never have worked, I
fixed it working (I guess) as part of this patch set. Sometimes
I wonder how this code got upstream in the first place, it
obviously is not tested.
mach-s3c64xx/mach-smartq.c has the same problem and additionally
defines the *same* GPIO line for MOSI and MISO which is not going
to be accepted by gpiolib. As the lines were number 1,2,2 I assumed
it was a typo and use lines 1,2,3. A comment gives awat that line 0
is chip select though no actual SPI device is provided for the LCD
supposed to be on this bit-banged SPI bus. I left it intact instead
of just deleting the bus though.
Kill off board file code that try to initialize the SPI lines
to the same values that they will later be set by the spi_gpio
driver anyways. Given the huge number of weird things in these
board files I do not think this code is very tested or put in
with much afterthought anyways.
In order to assert that we do not get performance regressions on
this crucial bing-banged driver, a ran a script like this dumping the
Ilitek ILI9322 regmap 10000 times (it has no caching obviously) on
an otherwise idle system in two iterations before and after the
patches:
#!/bin/sh
for run in `seq 10000`
do
cat /debug/regmap/spi0.0/registers > /dev/null
done
Before the patch:
time test.sh
real 3m 41.03s
user 0m 29.41s
sys 3m 7.22s
time test.sh
real 3m 44.24s
user 0m 32.31s
sys 3m 7.60s
After the patch:
time test.sh
real 3m 41.32s
user 0m 28.92s
sys 3m 8.08s
time test.sh
real 3m 39.92s
user 0m 30.20s
sys 3m 5.56s
So any performance differences seems to be in the error margin.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert to generalized SPI controller API introduced by the
commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"").
Inside driver variable name "master" is still used to indicate the driver
is master only.
While at it, change "unsigned cs" to "unsigned int cs" in
pxa2xx_spi_fw_translate_cs() to suppress checkpatch warning.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert to generalized SPI controller API introduced by the
commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"").
Inside driver variable name "master" is still used to indicate the driver
is master only.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AVR32 symbol was removed in commit 26202873bb ("avr32: remove
support for AVR32 architecture").
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move SSP idle waiting before CS deassert from error and end of message
handling function giveback() to cs_deassert(). This ensures idle waiting
is done also if there is CS change between transfers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Local struct chip_data has two members that are not used:
- cs. Looks like was never used
- enable_dma. Became unused by the commit f89a6d8f43 ("spi: dw-mid: move
to use core SPI DMA mappings").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the optional "axi" clk is deferred, we still need to undo some
initialisation. Especially 'master' must be released. It will be
reallocated the next time 'orion_spi_probe()' is called.
Add a new label to clean what needs to be cleaned and rename another
label to improve the names used.
Fixes: 92ae112e47 ("spi: orion: Fix clock resource by adding an optional bus clock")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings :
line 767: warning: incorrect type in assignment (different base types)
line 767: expected unsigned int [unsigned] [assigned] [usertype] val_out
line 767: got restricted __le32 [usertype] <noident>
line 776: warning: cast to restricted __le32
This takes advantage of readl/writel to do the endianness reordering,
and removes an extra variable in the function.
Fixes: f68a7dcb91 ("spi: a3700: Add full-duplex support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings :
line 504: warning: incorrect type in assignment (different base types)
line 504: expected unsigned int [unsigned] [usertype] val
line 504: got restricted __le32 [usertype] <noident>
line 527: warning: cast to restricted __le32
This is solved by removing endian-converson functions, since the
converted values are going through readl/writel anyway, which take care
of the conversion.
Fixes: 6fd6fd68c9 ("spi: armada-3700: Fix padding when sending not 4-byte aligned data")
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The armada 3700 SPI controller has support for full-duplex transfers,
but it can only be done without using the hardware FIFOs.
A full duplex transfer is done by shifting 4 bytes at a time, or even
one byte at a time for transfers less than 4 bytes long.
While this method is perfectly suitable for small transfers, it is still
slower than using the FIFOs.
This commit implement full-duplex support, making sure that half-duplex
transfers are still done using the FIFOs with the existing method.
Some setup functions were moved around to make sure the controller is
properly configured before beginning each transfer.
This was tested on EspressoBin with a logical analyser, and a simple
setup where MISO is connected on MOSI. Transfers were made from
userspace using spidev and spi-pipe from the spi-tools project
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The armada 3700 SPI controller allows to make transfers without using
the 32 bytes RFIFO and WFIFO.
This commit enable switching between FIFO and non-FIFO mode, which is
necessary to implement full-duplex transfers.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Armada 3700 SPI controller has an internal clock divider which can
divide the parent clock frequency by up to 30.
This patch sets the limits in the spi_controller fields so that we can
detect when a non-supported frequency is requested by a device for a
transfer.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
When performing a read using FIFO mode, the spi controller shifts out
the last 2 bytes that were written in a previous transfer on MOSI.
This undocumented behaviour can cause devices to misinterpret the
transfer, so we explicitly clear the WFIFO before each read.
This behaviour was noticed on EspressoBin.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly as well as mentioning
the mandatory clock which was also missing.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the original license statement with the SPDX identifier.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since clocks are disabled except during message transfer clocks
are also disabled when spi_imx_remove gets called. Accessing
registers leads to a freeeze at least on a i.MX 6ULL. Enable
clocks before disabling accessing the MXC_CSPICTRL register.
Fixes: 9e556dcc55 ("spi: spi-imx: only enable the clocks when we start to transfer a message")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch enables SPI DMA transfers for Atmel SAM9 SoCs and implements a
bounce buffer for transfers which have vmalloc allocated buffers. Those
buffers are not cache coherent even if they have been transformed into sg
lists. UBIFS is affected by this cache coherency issue.
In this patch I also reverted "spi: atmel: fix corrupted data issue on SAM9
family SoCs"(7094576ccd).
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using RX (with or without TX), the DMA interrupt triggers
completion when the RX FIFO has been emptied, i.e. after the full
transfer has finished.
However, when using TX without RX, the DMA interrupt triggers completion
as soon as the DMA engine has filled the TX FIFO, i.e. before the full
transfer has finished. Then sh_msiof_modify_ctr_wait() will spin until
the transfer has really finished and the TFSE bit is cleared, for at
most 1 ms. For slow speeds and/or large transfers, this may cause
timeouts and transfer failures:
spi_sh_msiof e6e10000.spi: failed to shut down hardware
74x164 spi2.0: SPI transfer failed: -110
spi_master spi2: failed to transfer one message from queue
74x164 spi2.0: Failed writing: -110
Fix this by waiting explicitly until the TX FIFO has been emptied.
Based on a patch in the BSP by Hiromitsu Yamasaki.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver creates a number of const structures that it stores in the
data field of an of_device_id array.
The data field of an of_device_id structure has type const void *, so
there is no need for a const-discarding cast when putting const values
into such a structure.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit makes transfer function use spi_transfer_is_last to
determine if currently processed transfer is the last one. Thanks to
that we finally set hardware registers properly and it makes controller
behave the way it's expected to.
This allows simplifying read function which can now simply start reading
from the slot 0 instead of the last saved offset. It has been
successfully tested using spi_write_then_read.
Moreover this change fixes handling messages with two writing transfers.
It's important for SPI flash devices as their drivers commonly use one
transfer for a command and another one for data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver creates various const structures that it stores in the
data field of an of_device_id array.
Adding const to the declaration of the location that receives the
const value from the data field ensures that the compiler will
continue to check that the value is not modified. Furthermore, the
const-discarding cast on the extraction from the data field is no
longer needed.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpiod_free() is an internal function for gpiolib, gpiod_put() is the
correct external function.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpio_free(gpio) simply does gpiod_free(gpio_to_desc(gpio)), so it's
simpler and cleaner to use gpiod_free directly.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The only part of atmel_spi_remove which needs to be atomic is hardware
reset.
atmel_spi_stop_dma calls dma_terminate_all and this needs interrupts
enabled.
atmel_spi_release_dma calls dma_release_channel and dma_release_channel
locks a mutex inside of spin_lock.
So the call of these functions can't be inside a spin_lock.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current support for GPIO chip selects assumes the GPIOs have been
configured by platform code or the boot loader. This includes pinmux
setup and GPIO direction. Hence it does not work as expected when just
described in DT using the "cs-gpios" property.
Fix this by:
1. using devm_gpiod_get_index() to request the GPIO, and thus
configure pinmux, if needed,
2. configuring the GPIO direction is the spi_master.setup() callback.
Use gpio_is_valid() instead of a check on positive numbers.
Note that when using GPIO chip selects, at least one native chip select
must be left unused, as that native chip select will be driven anyway,
and (global) native chip select polarity must be taken into account.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently only the MSIOF_SYNC signal can be used as a native chip
select. Extend support to up to 3 native chipselects using the
MSIOF_SS1 and MSIOF_SS2 signals.
Inspired by a patch in the BSP by Hiromitsu Yamasaki.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_master.setup() callback must not change configuration registers,
as that could corrupt I/O that is in progress for other SPI slaves.
The only exception is the configuration of the native chip select
polarity in SPI master mode, as a wrong chip select polarity will cause
havoc during all future transfers to any other SPI slave.
Hence stop writing to registers in sh_msiof_spi_setup(), unless it is
the first call for a controller using a native chip select, or unless
native chip select polarity has changed (note that you'll loose anyway
if I/O is in progress). Even then, only do what is strictly necessary,
instead of calling sh_msiof_spi_set_pin_regs().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
When probe function fails in registering the spi controller, the clock
should remain disabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Takuo Koguchi <takuo.koguchi.sw@hitachi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On SOC with multiple cpu (like omal l138) it is possible that spi
periferic is already initialized when this module is loaded and so
it is possible to recieve interrupt when the modules is not fully
initialized.
this patch initialize dspi->done before refister the interrupt
handler that use it
Signed-off-by: Michele Dionisio <michele.dionisio@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sun6i_spi_probe() uses sun6i_spi_runtime_resume() to prepare/enable
clocks, so sun6i_spi_remove() should use sun6i_spi_runtime_suspend() to
disable/unprepare them if we're not suspended.
Replacing pm_runtime_disable() by pm_runtime_force_suspend() will ensure
that sun6i_spi_runtime_suspend() is called if needed.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3558fe900e (spi: sunxi: Add Allwinner A31 SPI controller driver)
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
mclk and hclk need to be disabled. Since pm_runtime_disable does
not disable the clocks, use pm_runtime_force_suspend instead.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Takuo Koguchi <takuo.koguchi.sw@hitachi.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The R-Car Gen2 Hardware User Manual Rev. 2.00 states:
If the master/slave mode select bit (MSTR) is modified while the SPI
function enable bit (SPE) is set to 1 (that is, this module is
enabled), the subsequent operation cannot be guaranteed.
Hence do not set SPCR_SPE when setting SPCR_MSTR, just like the
.set_config_register() implementations for other RSPI variants do.
Note that when booted from QSPI, the boot loader will have set SPCR_MSTR
already, hence usually the bit is never modified by the Linux driver.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the helper introduced by commit e135303bd5 ("device: Add
dev_<level>_once variants") instead of open-coding the same
functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add new compatible string to support SPICC controller which
found at Amlogic Meson-AXG SoC. This is aiming at adding
a couple of enhanced feature patches.
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Armada 3700 SPI controller has 2 ranges of prescaler coefficients.
One ranging from 0 to 15 by steps of 1, and one ranging from 0 to 30 by
steps of 2.
This commit fixes the prescaler coefficients that are over 15 so that it
uses the correct range of values. The prescaling coefficient is rounded
to the upper value if it is odd.
This was tested on Espressobin with spidev and a locigal analyser.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When the core is configured in C_SPI_MODE > 0, it integrates a
lookup table that automatically configures the core in dual or quad mode
based on the command (first byte on the tx fifo).
Unfortunately, that list mode_?_memoy_*.mif does not contain all the
supported commands by the flash.
Since 4.14 spi-nor automatically tries to probe the flash using SFDP
(command 0x5a), and that command is not part of the list_mode table.
Whit the right combination of C_SPI_MODE and C_SPI_MEMORY this leads
into a stall that can only be recovered with a soft rest.
This patch detects this kind of stall and returns -EIO to the caller on
those commands. spi-nor can handle this error properly:
m25p80 spi0.0: Detected stall. Check C_SPI_MODE and C_SPI_MEMORY. 0x21 0x2404
m25p80 spi0.0: SPI transfer failed: -5
spi_master spi0: failed to transfer one message from queue
m25p80 spi0.0: s25sl064p (8192 Kbytes)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The driver as well as the controller support the SPI lsb first
mode. However, it's not possible to configure it e.g. when using
spidev. Adding this flag to mode_bits resolves the issue and lsb first
mode can be used.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the array is not present, assume all chip selects are native. This
is the standard behavior for SPI masters configured via the device
tree and the behavior of this driver as well when it is configured via
device tree.
This reduces platform data vs DT differences and allows most of the
platform data based boards to remove their chip select arrays.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the code that requests any chip select GPIOs fails, the cleanup of
spi_bitbang_start() by calling spi_bitbang_stop() is not done. Add this
to the failure path.
Note that spi_bitbang_start() has to be called before requesting GPIOs
because the GPIO data in the spi master is populated when the master is
registed, and that doesn't happen until spi_bitbang_start() is called.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver will fail to load if no gpio chip selects are specified,
this patch changes this so that it no longer fails.
It's possible to use all native chip selects, in which case there is
no reason to have a gpio chip select array. This is what happens if
the *optional* device tree property "cs-gpios" is omitted.
The spi core already checks for the absence of gpio chip selects in
the master and assigns any slaves the gpio_cs value of -ENOENT.
Also have the driver respect the standard SPI device tree property "num-cs"
to allow setting the number of chip selects without using cs-gpios.
CC: Mark Brown <broonie@kernel.org>
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 974488e4ce ("spi: imx: Fix failure path leak on GPIO request
error"), spi_bitbang_start() was moved later in the probe sequence. But
this doesn't work, as spi_bitbang_start() has to be called before
requesting GPIOs because the GPIO data in the spi master is populated when
the master is registed, and that doesn't happen until spi_bitbang_start()
is called. The default only works if one uses one CS.
So add a failure path call to spi_bitbang_stop() to fix the leak.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
CC: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer dev is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/spi/spi-sh-msiof.c:1198:2: warning: Value stored to 'dev'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer sci is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/spi/spi-s3c64xx.c:791:2: warning: Value stored to 'sci' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On systems where some controllers get a dynamic ID assigned and some have
a fixed number from DT, the current implemention might run into an IDR
collision if the dynamic controllers gets probed first and get an IDR number,
which is later requested by the controller with the fixed numbering. When
this happens the fixed controller will fail to register with the SPI core.
Fix this by skipping all known alias numbers when assigning the dynamic IDs.
Fixes: 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
The assignment of status to zero is never read, status is either
updated in the next iteration of the of the loop or several
lines after the end of the loop. Remove it, cleans up clang warning:
drivers/spi/spi-orion.c:674:4: warning: Value stored to 'status'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA supports 32-bit words only,
even if BITLEN1 of SITMDR2 register is 16bit.
Fixes: b0d0ce8b6b ("spi: sh-msiof: Add DMA support")
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the code that requests any chip select GPIOs fails, the cleanup of
spi_bitbang_start() by calling spi_bitbang_stop() is not done.
Fix this by moving spi_bitbang_start() to after the code that requets
GPIOs. The GPIOs are dev managed and don't need explicit cleanup.
Since spi_bitbang_start() is now the last operation, it doesn't need
to be cleaned up in the failure path.
CC: Shawn Guo <shawnguo@kernel.org>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Mark Brown <broonie@kernel.org>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Take an extra reference to the controller before deregistering it to
prevent use-after-free in the interrupt handler in case an interrupt
fires before the line is disabled.
Fixes: b1353d1c1d ("spi: Add Analog Devices AXI SPI Engine controller support")
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the fact that a reference to the controller is dropped as part
of deregistration.
This is an odd pattern as the reference is typically taken in
__spi_alloc_controller() rather than spi_register_controller(). Most
controller drivers gets it right these days and notably the
device-managed interface relies on this behaviour.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The controller is typically freed as part of device_unregister() so
store the bus id before deregistration to avoid use-after-free when the
id is later released.
Fixes: 9b61e30221 ("spi: Pick spi bus number from Linux idr or spi alias")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable <stable@vger.kernel.org>
When enabling the ADI hardware channels, if the channel id is 31,
then we will get one negative value -1 for BIT() macro, which will
write incorrect value to register.
Fixes: 7e2903cb91 ("spi: Add ADI driver for Spreadtrum platform")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Huibin Hong
Girish Mahadevan
Talel Shenhar
Rafał Miłecki
Trent Piepho
Axel Lin
Hieu Tran Dang
Nathan Chancellor
Lukasz Majewski
Gustavo A. R. Silva
Greg Kroah-Hartman
Leilk Liu
Marco Felsch
Geert Uytterhoeven
Arnd Bergmann
Boris Brezillon
David Lechner
Peter Shih
Jonas Gorski
Lubomir Rintel
Mark Brown
Alexey Khoroshilov
YueHaibing
Linus Walleij
Lee Jones
Chuanhua Han
Radu Pirea
Simon Goldschmidt
Hiromitsu Yamasaki
Gaku Inami
Kosta Zertsekel
Marcel Ziswiler
Alexandre Belloni
Lanqing Liu
Angelo Dureghello
Wolfram Sang
Linus Torvalds
Kirill Kapranov
Bartosz Golaszewski
Frieder Schrempf
Keiji Hayashibara
Lorenzo Bianconi
Ionela Voinescu
Colin Ian King
Tiago Brusamarello
Maxime Chevallier
Fabio Estevam
Andrey Smirnov
Wei Yongjun
Krzysztof Kozlowski
Mika Westerberg
Baolin Wang
Esben Haabendal
Jan Kundrát
Janek Kotas
Kees Cook
Rafael J. Wysocki
Tony Lindgren
Marek Szyprowski
Ulf Hansson
Tobias Jordan
Rob Herring
Kamal Dasu
Arvind Yadav
Stefan Potyra
Andy Shevchenko
Sylwester Nawrocki
kbuild test robot
sxauwsk
Geert Uytterhoeven
Jarkko Nikula
Naga Sureshkumar Relli
Vladimir Zapolskiy
wangbo
Stefan Agner
Christophe Jaillet
Eugen Hristev
Ulf Magnusson
Maxime Chevallier
Gregory CLEMENT
Andi Shyti
Julia Lawall
Rasmus Villemoes
Takuo Koguchi
Michele Dionisio
Sunny Luo
Ricardo Ribalda
Kurt Kanzenbach
Lucas Stach
Johan Hovold