WSL2-Linux-Kernel/drivers/gpio/gpio-mxs.c

398 строки
11 KiB
C
Исходник Обычный вид История

/*
* MXC GPIO support. (c) 2008 Daniel Mack <daniel@caiaq.de>
* Copyright 2008 Juergen Beisert, kernel@pengutronix.de
*
* Based on code from Freescale,
* Copyright (C) 2004-2010 Freescale Semiconductor, Inc. All Rights Reserved.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
* of the License, or (at your option) any later version.
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
* MA 02110-1301, USA.
*/
#include <linux/err.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/irqdomain.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
gpio: generic: factor into gpio_chip struct The separate struct bgpio_chip has been a pain to handle, both by being confusingly similar in name to struct gpio_chip and for being contained inside a struct so that struct gpio_chip is contained in a struct contained in a struct, making several steps of dereferencing necessary. Make things simpler: include the fields directly into <linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix some of the member variables with bgpio_* and add proper kerneldoc while we're at it. Modify all users to handle the change and use a struct gpio_chip directly. And while we're at it: replace all container_of() dereferencing by gpiochip_get_data() and registering the gpio_chip with gpiochip_add_data(). Cc: arm@kernel.org Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Kukjin Kim <kgene@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Olof Johansson <olof@lixom.net> Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Cc: Rabin Vincent <rabin@rab.in> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-04 16:02:58 +03:00
#include <linux/gpio/driver.h>
/* FIXME: for gpio_get_value(), replace this by direct register read */
#include <linux/gpio.h>
#include <linux/module.h>
#define MXS_SET 0x4
#define MXS_CLR 0x8
#define PINCTRL_DOUT(p) ((is_imx23_gpio(p) ? 0x0500 : 0x0700) + (p->id) * 0x10)
#define PINCTRL_DIN(p) ((is_imx23_gpio(p) ? 0x0600 : 0x0900) + (p->id) * 0x10)
#define PINCTRL_DOE(p) ((is_imx23_gpio(p) ? 0x0700 : 0x0b00) + (p->id) * 0x10)
#define PINCTRL_PIN2IRQ(p) ((is_imx23_gpio(p) ? 0x0800 : 0x1000) + (p->id) * 0x10)
#define PINCTRL_IRQEN(p) ((is_imx23_gpio(p) ? 0x0900 : 0x1100) + (p->id) * 0x10)
#define PINCTRL_IRQLEV(p) ((is_imx23_gpio(p) ? 0x0a00 : 0x1200) + (p->id) * 0x10)
#define PINCTRL_IRQPOL(p) ((is_imx23_gpio(p) ? 0x0b00 : 0x1300) + (p->id) * 0x10)
#define PINCTRL_IRQSTAT(p) ((is_imx23_gpio(p) ? 0x0c00 : 0x1400) + (p->id) * 0x10)
#define GPIO_INT_FALL_EDGE 0x0
#define GPIO_INT_LOW_LEV 0x1
#define GPIO_INT_RISE_EDGE 0x2
#define GPIO_INT_HIGH_LEV 0x3
#define GPIO_INT_LEV_MASK (1 << 0)
#define GPIO_INT_POL_MASK (1 << 1)
enum mxs_gpio_id {
IMX23_GPIO,
IMX28_GPIO,
};
struct mxs_gpio_port {
void __iomem *base;
int id;
int irq;
struct irq_domain *domain;
gpio: generic: factor into gpio_chip struct The separate struct bgpio_chip has been a pain to handle, both by being confusingly similar in name to struct gpio_chip and for being contained inside a struct so that struct gpio_chip is contained in a struct contained in a struct, making several steps of dereferencing necessary. Make things simpler: include the fields directly into <linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix some of the member variables with bgpio_* and add proper kerneldoc while we're at it. Modify all users to handle the change and use a struct gpio_chip directly. And while we're at it: replace all container_of() dereferencing by gpiochip_get_data() and registering the gpio_chip with gpiochip_add_data(). Cc: arm@kernel.org Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Kukjin Kim <kgene@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Olof Johansson <olof@lixom.net> Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Cc: Rabin Vincent <rabin@rab.in> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-04 16:02:58 +03:00
struct gpio_chip gc;
enum mxs_gpio_id devid;
u32 both_edges;
};
static inline int is_imx23_gpio(struct mxs_gpio_port *port)
{
return port->devid == IMX23_GPIO;
}
static inline int is_imx28_gpio(struct mxs_gpio_port *port)
{
return port->devid == IMX28_GPIO;
}
/* Note: This driver assumes 32 GPIOs are handled in one register */
static int mxs_gpio_set_irq_type(struct irq_data *d, unsigned int type)
{
u32 val;
u32 pin_mask = 1 << d->hwirq;
struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
gpio: mxs: fix duplicate level interrupts According to the reference manual level interrupts can't be acked using the IRQSTAT registers. The effect is that when a level interrupt triggers the following ack is a no-op and the same interrupt triggers again right after it has been unmasked after running the interrupt handler. The reference manual says: Status bits for pins configured as level sensitive interrupts cannot be cleared unless either the actual pin is in the non-interrupting state, or the pin has been disabled as an interrupt source by clearing its bit in HW_PINCTRL_PIN2IRQ. To work around the duplicated interrupts we can use the PIN2IRQ rather than the IRQEN registers to mask the interrupts. This probably does not work for the edge interrupts, so we have to split up the irq chip into two chip types, one for the level interrupts and one for the edge interrupts. We now make use of two different enable registers, so we have to take care to always enable the right one, especially during switching of the interrupt type. An easy way to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which makes sure that set_irq_type is called with masked interrupts. With this the flow to change the irq type is like: - core masks interrupt (using the current chip type) - mxs_gpio_set_irq_type() changes chip type if necessary - mxs_gpio_set_irq_type() unconditionally sets the enable bit in the now unused enable register - core eventually unmasks the interrupt (using the new chip type) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-21 16:11:38 +03:00
struct irq_chip_type *ct = irq_data_get_chip_type(d);
struct mxs_gpio_port *port = gc->private;
void __iomem *pin_addr;
int edge;
gpio: mxs: fix duplicate level interrupts According to the reference manual level interrupts can't be acked using the IRQSTAT registers. The effect is that when a level interrupt triggers the following ack is a no-op and the same interrupt triggers again right after it has been unmasked after running the interrupt handler. The reference manual says: Status bits for pins configured as level sensitive interrupts cannot be cleared unless either the actual pin is in the non-interrupting state, or the pin has been disabled as an interrupt source by clearing its bit in HW_PINCTRL_PIN2IRQ. To work around the duplicated interrupts we can use the PIN2IRQ rather than the IRQEN registers to mask the interrupts. This probably does not work for the edge interrupts, so we have to split up the irq chip into two chip types, one for the level interrupts and one for the edge interrupts. We now make use of two different enable registers, so we have to take care to always enable the right one, especially during switching of the interrupt type. An easy way to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which makes sure that set_irq_type is called with masked interrupts. With this the flow to change the irq type is like: - core masks interrupt (using the current chip type) - mxs_gpio_set_irq_type() changes chip type if necessary - mxs_gpio_set_irq_type() unconditionally sets the enable bit in the now unused enable register - core eventually unmasks the interrupt (using the new chip type) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-21 16:11:38 +03:00
if (!(ct->type & type))
if (irq_setup_alt_chip(d, type))
return -EINVAL;
port->both_edges &= ~pin_mask;
switch (type) {
case IRQ_TYPE_EDGE_BOTH:
gpio: generic: factor into gpio_chip struct The separate struct bgpio_chip has been a pain to handle, both by being confusingly similar in name to struct gpio_chip and for being contained inside a struct so that struct gpio_chip is contained in a struct contained in a struct, making several steps of dereferencing necessary. Make things simpler: include the fields directly into <linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix some of the member variables with bgpio_* and add proper kerneldoc while we're at it. Modify all users to handle the change and use a struct gpio_chip directly. And while we're at it: replace all container_of() dereferencing by gpiochip_get_data() and registering the gpio_chip with gpiochip_add_data(). Cc: arm@kernel.org Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Kukjin Kim <kgene@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Olof Johansson <olof@lixom.net> Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Cc: Rabin Vincent <rabin@rab.in> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-04 16:02:58 +03:00
val = gpio_get_value(port->gc.base + d->hwirq);
if (val)
edge = GPIO_INT_FALL_EDGE;
else
edge = GPIO_INT_RISE_EDGE;
port->both_edges |= pin_mask;
break;
case IRQ_TYPE_EDGE_RISING:
edge = GPIO_INT_RISE_EDGE;
break;
case IRQ_TYPE_EDGE_FALLING:
edge = GPIO_INT_FALL_EDGE;
break;
case IRQ_TYPE_LEVEL_LOW:
edge = GPIO_INT_LOW_LEV;
break;
case IRQ_TYPE_LEVEL_HIGH:
edge = GPIO_INT_HIGH_LEV;
break;
default:
return -EINVAL;
}
/* set level or edge */
pin_addr = port->base + PINCTRL_IRQLEV(port);
gpio: mxs: fix duplicate level interrupts According to the reference manual level interrupts can't be acked using the IRQSTAT registers. The effect is that when a level interrupt triggers the following ack is a no-op and the same interrupt triggers again right after it has been unmasked after running the interrupt handler. The reference manual says: Status bits for pins configured as level sensitive interrupts cannot be cleared unless either the actual pin is in the non-interrupting state, or the pin has been disabled as an interrupt source by clearing its bit in HW_PINCTRL_PIN2IRQ. To work around the duplicated interrupts we can use the PIN2IRQ rather than the IRQEN registers to mask the interrupts. This probably does not work for the edge interrupts, so we have to split up the irq chip into two chip types, one for the level interrupts and one for the edge interrupts. We now make use of two different enable registers, so we have to take care to always enable the right one, especially during switching of the interrupt type. An easy way to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which makes sure that set_irq_type is called with masked interrupts. With this the flow to change the irq type is like: - core masks interrupt (using the current chip type) - mxs_gpio_set_irq_type() changes chip type if necessary - mxs_gpio_set_irq_type() unconditionally sets the enable bit in the now unused enable register - core eventually unmasks the interrupt (using the new chip type) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-21 16:11:38 +03:00
if (edge & GPIO_INT_LEV_MASK) {
writel(pin_mask, pin_addr + MXS_SET);
gpio: mxs: fix duplicate level interrupts According to the reference manual level interrupts can't be acked using the IRQSTAT registers. The effect is that when a level interrupt triggers the following ack is a no-op and the same interrupt triggers again right after it has been unmasked after running the interrupt handler. The reference manual says: Status bits for pins configured as level sensitive interrupts cannot be cleared unless either the actual pin is in the non-interrupting state, or the pin has been disabled as an interrupt source by clearing its bit in HW_PINCTRL_PIN2IRQ. To work around the duplicated interrupts we can use the PIN2IRQ rather than the IRQEN registers to mask the interrupts. This probably does not work for the edge interrupts, so we have to split up the irq chip into two chip types, one for the level interrupts and one for the edge interrupts. We now make use of two different enable registers, so we have to take care to always enable the right one, especially during switching of the interrupt type. An easy way to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which makes sure that set_irq_type is called with masked interrupts. With this the flow to change the irq type is like: - core masks interrupt (using the current chip type) - mxs_gpio_set_irq_type() changes chip type if necessary - mxs_gpio_set_irq_type() unconditionally sets the enable bit in the now unused enable register - core eventually unmasks the interrupt (using the new chip type) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-21 16:11:38 +03:00
writel(pin_mask, port->base + PINCTRL_IRQEN(port) + MXS_SET);
} else {
writel(pin_mask, pin_addr + MXS_CLR);
gpio: mxs: fix duplicate level interrupts According to the reference manual level interrupts can't be acked using the IRQSTAT registers. The effect is that when a level interrupt triggers the following ack is a no-op and the same interrupt triggers again right after it has been unmasked after running the interrupt handler. The reference manual says: Status bits for pins configured as level sensitive interrupts cannot be cleared unless either the actual pin is in the non-interrupting state, or the pin has been disabled as an interrupt source by clearing its bit in HW_PINCTRL_PIN2IRQ. To work around the duplicated interrupts we can use the PIN2IRQ rather than the IRQEN registers to mask the interrupts. This probably does not work for the edge interrupts, so we have to split up the irq chip into two chip types, one for the level interrupts and one for the edge interrupts. We now make use of two different enable registers, so we have to take care to always enable the right one, especially during switching of the interrupt type. An easy way to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which makes sure that set_irq_type is called with masked interrupts. With this the flow to change the irq type is like: - core masks interrupt (using the current chip type) - mxs_gpio_set_irq_type() changes chip type if necessary - mxs_gpio_set_irq_type() unconditionally sets the enable bit in the now unused enable register - core eventually unmasks the interrupt (using the new chip type) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-21 16:11:38 +03:00
writel(pin_mask, port->base + PINCTRL_PIN2IRQ(port) + MXS_SET);
}
/* set polarity */
pin_addr = port->base + PINCTRL_IRQPOL(port);
if (edge & GPIO_INT_POL_MASK)
writel(pin_mask, pin_addr + MXS_SET);
else
writel(pin_mask, pin_addr + MXS_CLR);
writel(pin_mask,
port->base + PINCTRL_IRQSTAT(port) + MXS_CLR);
return 0;
}
static void mxs_flip_edge(struct mxs_gpio_port *port, u32 gpio)
{
u32 bit, val, edge;
void __iomem *pin_addr;
bit = 1 << gpio;
pin_addr = port->base + PINCTRL_IRQPOL(port);
val = readl(pin_addr);
edge = val & bit;
if (edge)
writel(bit, pin_addr + MXS_CLR);
else
writel(bit, pin_addr + MXS_SET);
}
/* MXS has one interrupt *per* gpio port */
static void mxs_gpio_irq_handler(struct irq_desc *desc)
{
u32 irq_stat;
struct mxs_gpio_port *port = irq_desc_get_handler_data(desc);
desc->irq_data.chip->irq_ack(&desc->irq_data);
irq_stat = readl(port->base + PINCTRL_IRQSTAT(port)) &
readl(port->base + PINCTRL_IRQEN(port));
while (irq_stat != 0) {
int irqoffset = fls(irq_stat) - 1;
if (port->both_edges & (1 << irqoffset))
mxs_flip_edge(port, irqoffset);
generic_handle_irq(irq_find_mapping(port->domain, irqoffset));
irq_stat &= ~(1 << irqoffset);
}
}
/*
* Set interrupt number "irq" in the GPIO as a wake-up source.
* While system is running, all registered GPIO interrupts need to have
* wake-up enabled. When system is suspended, only selected GPIO interrupts
* need to have wake-up enabled.
* @param irq interrupt source number
* @param enable enable as wake-up if equal to non-zero
* @return This function returns 0 on success.
*/
static int mxs_gpio_set_wake_irq(struct irq_data *d, unsigned int enable)
{
struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
struct mxs_gpio_port *port = gc->private;
if (enable)
enable_irq_wake(port->irq);
else
disable_irq_wake(port->irq);
return 0;
}
static int mxs_gpio_init_gc(struct mxs_gpio_port *port, int irq_base)
{
struct irq_chip_generic *gc;
struct irq_chip_type *ct;
gpio: mxs: fix duplicate level interrupts According to the reference manual level interrupts can't be acked using the IRQSTAT registers. The effect is that when a level interrupt triggers the following ack is a no-op and the same interrupt triggers again right after it has been unmasked after running the interrupt handler. The reference manual says: Status bits for pins configured as level sensitive interrupts cannot be cleared unless either the actual pin is in the non-interrupting state, or the pin has been disabled as an interrupt source by clearing its bit in HW_PINCTRL_PIN2IRQ. To work around the duplicated interrupts we can use the PIN2IRQ rather than the IRQEN registers to mask the interrupts. This probably does not work for the edge interrupts, so we have to split up the irq chip into two chip types, one for the level interrupts and one for the edge interrupts. We now make use of two different enable registers, so we have to take care to always enable the right one, especially during switching of the interrupt type. An easy way to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which makes sure that set_irq_type is called with masked interrupts. With this the flow to change the irq type is like: - core masks interrupt (using the current chip type) - mxs_gpio_set_irq_type() changes chip type if necessary - mxs_gpio_set_irq_type() unconditionally sets the enable bit in the now unused enable register - core eventually unmasks the interrupt (using the new chip type) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-21 16:11:38 +03:00
gc = irq_alloc_generic_chip("gpio-mxs", 2, irq_base,
port->base, handle_level_irq);
if (!gc)
return -ENOMEM;
gc->private = port;
gpio: mxs: fix duplicate level interrupts According to the reference manual level interrupts can't be acked using the IRQSTAT registers. The effect is that when a level interrupt triggers the following ack is a no-op and the same interrupt triggers again right after it has been unmasked after running the interrupt handler. The reference manual says: Status bits for pins configured as level sensitive interrupts cannot be cleared unless either the actual pin is in the non-interrupting state, or the pin has been disabled as an interrupt source by clearing its bit in HW_PINCTRL_PIN2IRQ. To work around the duplicated interrupts we can use the PIN2IRQ rather than the IRQEN registers to mask the interrupts. This probably does not work for the edge interrupts, so we have to split up the irq chip into two chip types, one for the level interrupts and one for the edge interrupts. We now make use of two different enable registers, so we have to take care to always enable the right one, especially during switching of the interrupt type. An easy way to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which makes sure that set_irq_type is called with masked interrupts. With this the flow to change the irq type is like: - core masks interrupt (using the current chip type) - mxs_gpio_set_irq_type() changes chip type if necessary - mxs_gpio_set_irq_type() unconditionally sets the enable bit in the now unused enable register - core eventually unmasks the interrupt (using the new chip type) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-21 16:11:38 +03:00
ct = &gc->chip_types[0];
ct->type = IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW;
ct->chip.irq_ack = irq_gc_ack_set_bit;
ct->chip.irq_mask = irq_gc_mask_disable_reg;
ct->chip.irq_unmask = irq_gc_unmask_enable_reg;
ct->chip.irq_set_type = mxs_gpio_set_irq_type;
ct->chip.irq_set_wake = mxs_gpio_set_wake_irq;
ct->chip.flags = IRQCHIP_SET_TYPE_MASKED;
ct->regs.ack = PINCTRL_IRQSTAT(port) + MXS_CLR;
ct->regs.enable = PINCTRL_PIN2IRQ(port) + MXS_SET;
ct->regs.disable = PINCTRL_PIN2IRQ(port) + MXS_CLR;
ct = &gc->chip_types[1];
ct->type = IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING;
ct->chip.irq_ack = irq_gc_ack_set_bit;
ct->chip.irq_mask = irq_gc_mask_disable_reg;
ct->chip.irq_unmask = irq_gc_unmask_enable_reg;
ct->chip.irq_set_type = mxs_gpio_set_irq_type;
ct->chip.irq_set_wake = mxs_gpio_set_wake_irq;
gpio: mxs: fix duplicate level interrupts According to the reference manual level interrupts can't be acked using the IRQSTAT registers. The effect is that when a level interrupt triggers the following ack is a no-op and the same interrupt triggers again right after it has been unmasked after running the interrupt handler. The reference manual says: Status bits for pins configured as level sensitive interrupts cannot be cleared unless either the actual pin is in the non-interrupting state, or the pin has been disabled as an interrupt source by clearing its bit in HW_PINCTRL_PIN2IRQ. To work around the duplicated interrupts we can use the PIN2IRQ rather than the IRQEN registers to mask the interrupts. This probably does not work for the edge interrupts, so we have to split up the irq chip into two chip types, one for the level interrupts and one for the edge interrupts. We now make use of two different enable registers, so we have to take care to always enable the right one, especially during switching of the interrupt type. An easy way to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which makes sure that set_irq_type is called with masked interrupts. With this the flow to change the irq type is like: - core masks interrupt (using the current chip type) - mxs_gpio_set_irq_type() changes chip type if necessary - mxs_gpio_set_irq_type() unconditionally sets the enable bit in the now unused enable register - core eventually unmasks the interrupt (using the new chip type) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-21 16:11:38 +03:00
ct->chip.flags = IRQCHIP_SET_TYPE_MASKED;
ct->regs.ack = PINCTRL_IRQSTAT(port) + MXS_CLR;
ct->regs.enable = PINCTRL_IRQEN(port) + MXS_SET;
ct->regs.disable = PINCTRL_IRQEN(port) + MXS_CLR;
gpio: mxs: fix duplicate level interrupts According to the reference manual level interrupts can't be acked using the IRQSTAT registers. The effect is that when a level interrupt triggers the following ack is a no-op and the same interrupt triggers again right after it has been unmasked after running the interrupt handler. The reference manual says: Status bits for pins configured as level sensitive interrupts cannot be cleared unless either the actual pin is in the non-interrupting state, or the pin has been disabled as an interrupt source by clearing its bit in HW_PINCTRL_PIN2IRQ. To work around the duplicated interrupts we can use the PIN2IRQ rather than the IRQEN registers to mask the interrupts. This probably does not work for the edge interrupts, so we have to split up the irq chip into two chip types, one for the level interrupts and one for the edge interrupts. We now make use of two different enable registers, so we have to take care to always enable the right one, especially during switching of the interrupt type. An easy way to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which makes sure that set_irq_type is called with masked interrupts. With this the flow to change the irq type is like: - core masks interrupt (using the current chip type) - mxs_gpio_set_irq_type() changes chip type if necessary - mxs_gpio_set_irq_type() unconditionally sets the enable bit in the now unused enable register - core eventually unmasks the interrupt (using the new chip type) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-21 16:11:38 +03:00
ct->handler = handle_level_irq;
gpio: mxs: Allow for recursive enable_irq_wake() call The scenario here is that someone calls enable_irq_wake() from somewhere in the code. This will result in the lockdep producing a backtrace as can be seen below. In my case, this problem is triggered when using the wl1271 (TI WlCore) driver found in drivers/net/wireless/ti/ . The problem cause is rather obvious from the backtrace, but let's outline the dependency. enable_irq_wake() grabs the IRQ buslock in irq_set_irq_wake(), which in turns calls mxs_gpio_set_wake_irq() . But mxs_gpio_set_wake_irq() calls enable_irq_wake() again on the one-level-higher IRQ , thus it tries to grab the IRQ buslock again in irq_set_irq_wake() . Because the spinlock in irq_set_irq_wake()->irq_get_desc_buslock()->__irq_get_desc_lock() is not marked as recursive, lockdep will spew the stuff below. We know we can safely re-enter the lock, so use IRQ_GC_INIT_NESTED_LOCK to fix the spew. ============================================= [ INFO: possible recursive locking detected ] 3.10.33-00012-gf06b763-dirty #61 Not tainted --------------------------------------------- kworker/0:1/18 is trying to acquire lock: (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88 but task is already holding lock: (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&irq_desc_lock_class); lock(&irq_desc_lock_class); *** DEADLOCK *** May be due to missing lock nesting notation 3 locks held by kworker/0:1/18: #0: (events){.+.+.+}, at: [<c0036308>] process_one_work+0x134/0x4a4 #1: ((&fw_work->work)){+.+.+.}, at: [<c0036308>] process_one_work+0x134/0x4a4 #2: (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88 stack backtrace: CPU: 0 PID: 18 Comm: kworker/0:1 Not tainted 3.10.33-00012-gf06b763-dirty #61 Workqueue: events request_firmware_work_func [<c0013eb4>] (unwind_backtrace+0x0/0xf0) from [<c0011c74>] (show_stack+0x10/0x14) [<c0011c74>] (show_stack+0x10/0x14) from [<c005bb08>] (__lock_acquire+0x140c/0x1a64) [<c005bb08>] (__lock_acquire+0x140c/0x1a64) from [<c005c6a8>] (lock_acquire+0x9c/0x104) [<c005c6a8>] (lock_acquire+0x9c/0x104) from [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58) [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58) from [<c00685f0>] (__irq_get_desc_lock+0x48/0x88) [<c00685f0>] (__irq_get_desc_lock+0x48/0x88) from [<c0068e78>] (irq_set_irq_wake+0x20/0xf4) [<c0068e78>] (irq_set_irq_wake+0x20/0xf4) from [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24) [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24) from [<c0068cf4>] (set_irq_wake_real+0x30/0x44) [<c0068cf4>] (set_irq_wake_real+0x30/0x44) from [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4) [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4) from [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c) [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c) from [<c02be5e8>] (request_firmware_work_func+0x38/0x58) [<c02be5e8>] (request_firmware_work_func+0x38/0x58) from [<c0036394>] (process_one_work+0x1c0/0x4a4) [<c0036394>] (process_one_work+0x1c0/0x4a4) from [<c0036a4c>] (worker_thread+0x138/0x394) [<c0036a4c>] (worker_thread+0x138/0x394) from [<c003cb74>] (kthread+0xa4/0xb0) [<c003cb74>] (kthread+0xa4/0xb0) from [<c000ee00>] (ret_from_fork+0x14/0x34) wlcore: loaded Cc: stable@vger.kernel.org Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-03-24 06:38:10 +04:00
irq_setup_generic_chip(gc, IRQ_MSK(32), IRQ_GC_INIT_NESTED_LOCK,
IRQ_NOREQUEST, 0);
return 0;
}
static int mxs_gpio_to_irq(struct gpio_chip *gc, unsigned offset)
{
gpio: generic: factor into gpio_chip struct The separate struct bgpio_chip has been a pain to handle, both by being confusingly similar in name to struct gpio_chip and for being contained inside a struct so that struct gpio_chip is contained in a struct contained in a struct, making several steps of dereferencing necessary. Make things simpler: include the fields directly into <linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix some of the member variables with bgpio_* and add proper kerneldoc while we're at it. Modify all users to handle the change and use a struct gpio_chip directly. And while we're at it: replace all container_of() dereferencing by gpiochip_get_data() and registering the gpio_chip with gpiochip_add_data(). Cc: arm@kernel.org Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Kukjin Kim <kgene@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Olof Johansson <olof@lixom.net> Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Cc: Rabin Vincent <rabin@rab.in> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-04 16:02:58 +03:00
struct mxs_gpio_port *port = gpiochip_get_data(gc);
return irq_find_mapping(port->domain, offset);
}
static int mxs_gpio_get_direction(struct gpio_chip *gc, unsigned offset)
{
gpio: generic: factor into gpio_chip struct The separate struct bgpio_chip has been a pain to handle, both by being confusingly similar in name to struct gpio_chip and for being contained inside a struct so that struct gpio_chip is contained in a struct contained in a struct, making several steps of dereferencing necessary. Make things simpler: include the fields directly into <linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix some of the member variables with bgpio_* and add proper kerneldoc while we're at it. Modify all users to handle the change and use a struct gpio_chip directly. And while we're at it: replace all container_of() dereferencing by gpiochip_get_data() and registering the gpio_chip with gpiochip_add_data(). Cc: arm@kernel.org Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Kukjin Kim <kgene@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Olof Johansson <olof@lixom.net> Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Cc: Rabin Vincent <rabin@rab.in> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-04 16:02:58 +03:00
struct mxs_gpio_port *port = gpiochip_get_data(gc);
u32 mask = 1 << offset;
u32 dir;
dir = readl(port->base + PINCTRL_DOE(port));
return !(dir & mask);
}
static const struct platform_device_id mxs_gpio_ids[] = {
{
.name = "imx23-gpio",
.driver_data = IMX23_GPIO,
}, {
.name = "imx28-gpio",
.driver_data = IMX28_GPIO,
}, {
/* sentinel */
}
};
MODULE_DEVICE_TABLE(platform, mxs_gpio_ids);
static const struct of_device_id mxs_gpio_dt_ids[] = {
{ .compatible = "fsl,imx23-gpio", .data = (void *) IMX23_GPIO, },
{ .compatible = "fsl,imx28-gpio", .data = (void *) IMX28_GPIO, },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, mxs_gpio_dt_ids);
static int mxs_gpio_probe(struct platform_device *pdev)
{
const struct of_device_id *of_id =
of_match_device(mxs_gpio_dt_ids, &pdev->dev);
struct device_node *np = pdev->dev.of_node;
struct device_node *parent;
static void __iomem *base;
struct mxs_gpio_port *port;
int irq_base;
int err;
port = devm_kzalloc(&pdev->dev, sizeof(*port), GFP_KERNEL);
if (!port)
return -ENOMEM;
port->id = of_alias_get_id(np, "gpio");
if (port->id < 0)
return port->id;
port->devid = (enum mxs_gpio_id) of_id->data;
port->irq = platform_get_irq(pdev, 0);
if (port->irq < 0)
return port->irq;
/*
* map memory region only once, as all the gpio ports
* share the same one
*/
if (!base) {
parent = of_get_parent(np);
base = of_iomap(parent, 0);
of_node_put(parent);
if (!base)
return -EADDRNOTAVAIL;
}
port->base = base;
gpio: mxs: fix duplicate level interrupts According to the reference manual level interrupts can't be acked using the IRQSTAT registers. The effect is that when a level interrupt triggers the following ack is a no-op and the same interrupt triggers again right after it has been unmasked after running the interrupt handler. The reference manual says: Status bits for pins configured as level sensitive interrupts cannot be cleared unless either the actual pin is in the non-interrupting state, or the pin has been disabled as an interrupt source by clearing its bit in HW_PINCTRL_PIN2IRQ. To work around the duplicated interrupts we can use the PIN2IRQ rather than the IRQEN registers to mask the interrupts. This probably does not work for the edge interrupts, so we have to split up the irq chip into two chip types, one for the level interrupts and one for the edge interrupts. We now make use of two different enable registers, so we have to take care to always enable the right one, especially during switching of the interrupt type. An easy way to accomplish this is to use the IRQCHIP_SET_TYPE_MASKED which makes sure that set_irq_type is called with masked interrupts. With this the flow to change the irq type is like: - core masks interrupt (using the current chip type) - mxs_gpio_set_irq_type() changes chip type if necessary - mxs_gpio_set_irq_type() unconditionally sets the enable bit in the now unused enable register - core eventually unmasks the interrupt (using the new chip type) Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-21 16:11:38 +03:00
/* initially disable the interrupts */
writel(0, port->base + PINCTRL_PIN2IRQ(port));
writel(0, port->base + PINCTRL_IRQEN(port));
/* clear address has to be used to clear IRQSTAT bits */
writel(~0U, port->base + PINCTRL_IRQSTAT(port) + MXS_CLR);
irq_base = devm_irq_alloc_descs(&pdev->dev, -1, 0, 32, numa_node_id());
if (irq_base < 0) {
err = irq_base;
goto out_iounmap;
}
port->domain = irq_domain_add_legacy(np, 32, irq_base, 0,
&irq_domain_simple_ops, NULL);
if (!port->domain) {
err = -ENODEV;
goto out_iounmap;
}
/* gpio-mxs can be a generic irq chip */
err = mxs_gpio_init_gc(port, irq_base);
if (err < 0)
goto out_irqdomain_remove;
/* setup one handler for each entry */
irq_set_chained_handler_and_data(port->irq, mxs_gpio_irq_handler,
port);
gpio: generic: factor into gpio_chip struct The separate struct bgpio_chip has been a pain to handle, both by being confusingly similar in name to struct gpio_chip and for being contained inside a struct so that struct gpio_chip is contained in a struct contained in a struct, making several steps of dereferencing necessary. Make things simpler: include the fields directly into <linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix some of the member variables with bgpio_* and add proper kerneldoc while we're at it. Modify all users to handle the change and use a struct gpio_chip directly. And while we're at it: replace all container_of() dereferencing by gpiochip_get_data() and registering the gpio_chip with gpiochip_add_data(). Cc: arm@kernel.org Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Kukjin Kim <kgene@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Olof Johansson <olof@lixom.net> Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Cc: Rabin Vincent <rabin@rab.in> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-04 16:02:58 +03:00
err = bgpio_init(&port->gc, &pdev->dev, 4,
port->base + PINCTRL_DIN(port),
port->base + PINCTRL_DOUT(port) + MXS_SET,
port->base + PINCTRL_DOUT(port) + MXS_CLR,
arm-soc: device tree conversions, part 2 These continue the device tree work from part 1, this set is for the tegra, mxs and imx platforms, all of which have dependencies on clock or pinctrl changes submitted earlier. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.11 (GNU/Linux) iQIcBAABAgAGBQJPuex7AAoJEIwa5zzehBx3xsQP/jkyt74MvuKUi8pi2zkeMIgn 4XieyqcA0KZjJzfB22q3GIZjNIf/mEIGE4E/3bneVMPh/E2zaiohaXFExBmjNjml hhzWeZlFGPBjrZsfpIXJIIUhwSI7gX2rjYh4npJmdNhZmy8Y89XnpNJhN1kOwMuV oN23hPWoSVGbyDMQ0fmHx9GyOL8m7yap+joG13aljDa2OKpQg+pYvdwft+k1K9di 8yPF+qA043UUR7dSsjmTbiCcjZy2eySdCmfOAkEG4inSgxNoM7GBs3MuwZo/veCD v5WssJqWDbLXtqKn5Uo2bvGWiEcf0xtwOAqhSpbaup3dQFJSWMEenBTtA9UlxFhk 6gdY62O+7k6N0thkxXyLNGkgaGzexZAsK7dM6XSDB+PqD+OSNJS7dvmxZM8tuaRn rvCM1XWcNeN/dpnLbgwCR12efkwWtJoqqUZUUp/tFFaTo8HriqeAIYk7obnR8s9n S5x9LeueQGNgaxXJzVdh481YKG/1lqjG/a06HbVgYS4XQvtdA+4khalOefJv10tm Nkg8+4/8pMthWJfhhlfPUgWFXOXFF2AGPG4su2XwKuFXypO8599lzi7gUQaEZu2U 7caqoWP69KsKvK5iAAmA4DQ2rcsgHd44NXx/8Jjes9ma8knlYjrf42dBH6AZMQBG 69I9sJ1cyqusBwx72NPN =WeDQ -----END PGP SIGNATURE----- Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull arm-soc device tree conversions (part 2) from Olof Johansson: "These continue the device tree work from part 1, this set is for the tegra, mxs and imx platforms, all of which have dependencies on clock or pinctrl changes submitted earlier." Fix up trivial conflicts due to nearby changes in drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c * tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits) ARM: dt: tegra: invert status=disable vs status=okay ARM: dt: tegra: consistent basic property ordering ARM: dt: tegra: sort nodes based on bus order ARM: dt: tegra: remove duplicate device_type property ARM: dt: tegra: consistenly use lower-case for hex constants ARM: dt: tegra: format regs properties consistently ARM: dt: tegra: gpio comment cleanup ARM: dt: tegra: remove unnecessary unit addresses ARM: dt: tegra: whitespace cleanup ARM: dt: tegra cardhu: fix typo in SDHCI node name ARM: dt: tegra: cardhu: register core regulator tps62361 ARM: dt: tegra30.dtsi: Add SMMU node ARM: dt: tegra20.dtsi: Add GART node ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes ARM: dt: tegra: Add device tree support for AHB ARM: dts: enable audio support for imx28-evk ARM: dts: enable i2c device for imx28-evk i2c: mxs: add device tree probe support ARM: dts: enable mmc for imx28-evk ...
2012-05-26 23:57:47 +04:00
port->base + PINCTRL_DOE(port), NULL, 0);
if (err)
gpio: generic: factor into gpio_chip struct The separate struct bgpio_chip has been a pain to handle, both by being confusingly similar in name to struct gpio_chip and for being contained inside a struct so that struct gpio_chip is contained in a struct contained in a struct, making several steps of dereferencing necessary. Make things simpler: include the fields directly into <linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix some of the member variables with bgpio_* and add proper kerneldoc while we're at it. Modify all users to handle the change and use a struct gpio_chip directly. And while we're at it: replace all container_of() dereferencing by gpiochip_get_data() and registering the gpio_chip with gpiochip_add_data(). Cc: arm@kernel.org Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Kukjin Kim <kgene@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Olof Johansson <olof@lixom.net> Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Cc: Rabin Vincent <rabin@rab.in> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-04 16:02:58 +03:00
goto out_irqdomain_remove;
gpio: generic: factor into gpio_chip struct The separate struct bgpio_chip has been a pain to handle, both by being confusingly similar in name to struct gpio_chip and for being contained inside a struct so that struct gpio_chip is contained in a struct contained in a struct, making several steps of dereferencing necessary. Make things simpler: include the fields directly into <linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix some of the member variables with bgpio_* and add proper kerneldoc while we're at it. Modify all users to handle the change and use a struct gpio_chip directly. And while we're at it: replace all container_of() dereferencing by gpiochip_get_data() and registering the gpio_chip with gpiochip_add_data(). Cc: arm@kernel.org Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Kukjin Kim <kgene@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Olof Johansson <olof@lixom.net> Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Cc: Rabin Vincent <rabin@rab.in> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-04 16:02:58 +03:00
port->gc.to_irq = mxs_gpio_to_irq;
port->gc.get_direction = mxs_gpio_get_direction;
port->gc.base = port->id * 32;
gpio: generic: factor into gpio_chip struct The separate struct bgpio_chip has been a pain to handle, both by being confusingly similar in name to struct gpio_chip and for being contained inside a struct so that struct gpio_chip is contained in a struct contained in a struct, making several steps of dereferencing necessary. Make things simpler: include the fields directly into <linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix some of the member variables with bgpio_* and add proper kerneldoc while we're at it. Modify all users to handle the change and use a struct gpio_chip directly. And while we're at it: replace all container_of() dereferencing by gpiochip_get_data() and registering the gpio_chip with gpiochip_add_data(). Cc: arm@kernel.org Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Kukjin Kim <kgene@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Olof Johansson <olof@lixom.net> Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Cc: Rabin Vincent <rabin@rab.in> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-04 16:02:58 +03:00
err = gpiochip_add_data(&port->gc, port);
if (err)
gpio: generic: factor into gpio_chip struct The separate struct bgpio_chip has been a pain to handle, both by being confusingly similar in name to struct gpio_chip and for being contained inside a struct so that struct gpio_chip is contained in a struct contained in a struct, making several steps of dereferencing necessary. Make things simpler: include the fields directly into <linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix some of the member variables with bgpio_* and add proper kerneldoc while we're at it. Modify all users to handle the change and use a struct gpio_chip directly. And while we're at it: replace all container_of() dereferencing by gpiochip_get_data() and registering the gpio_chip with gpiochip_add_data(). Cc: arm@kernel.org Cc: Alexander Shiyan <shc_work@mail.ru> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Kukjin Kim <kgene@kernel.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Sudeep Holla <sudeep.holla@arm.com> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Olof Johansson <olof@lixom.net> Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com> Cc: Rabin Vincent <rabin@rab.in> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-omap@vger.kernel.org Cc: linux-samsung-soc@vger.kernel.org Cc: bcm-kernel-feedback-list@broadcom.com Acked-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-12-04 16:02:58 +03:00
goto out_irqdomain_remove;
return 0;
out_irqdomain_remove:
irq_domain_remove(port->domain);
out_iounmap:
iounmap(port->base);
return err;
}
static struct platform_driver mxs_gpio_driver = {
.driver = {
.name = "gpio-mxs",
.of_match_table = mxs_gpio_dt_ids,
},
.probe = mxs_gpio_probe,
.id_table = mxs_gpio_ids,
};
static int __init mxs_gpio_init(void)
{
return platform_driver_register(&mxs_gpio_driver);
}
postcore_initcall(mxs_gpio_init);
MODULE_AUTHOR("Freescale Semiconductor, "
"Daniel Mack <danielncaiaq.de>, "
"Juergen Beisert <kernel@pengutronix.de>");
MODULE_DESCRIPTION("Freescale MXS GPIO");
MODULE_LICENSE("GPL");