Large Receive Offload (LRO) is only appropriate for packets that are
destined for the host, and should be disabled if received packets may be
forwarded. It can also confuse the GSO on output.
Add dev_disable_lro() function which uses the appropriate ethtool ops to
disable LRO if enabled.
Add calls to dev_disable_lro() in br_add_if() and functions that enable
IPv4 and IPv6 forwarding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4960, Section 11.4. Protection of Non-SCTP-Capable Hosts
When an SCTP stack receives a packet containing multiple control or
DATA chunks and the processing of the packet requires the sending of
multiple chunks in response, the sender of the response chunk(s) MUST
NOT send more than one packet. If bundling is supported, multiple
response chunks that fit into a single packet MAY be bundled together
into one single response packet. If bundling is not supported, then
the sender MUST NOT send more than one response chunk and MUST
discard all other responses. Note that this rule does NOT apply to a
SACK chunk, since a SACK chunk is, in itself, a response to DATA and
a SACK does not require a response of more DATA.
We implement this by not servicing our outqueue until we reach the end
of the packet. This enables maximum bundling. We also identify
'response' chunks and make sure that we only send 1 packet when sending
such chunks.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add to validate initiate tag and chunk type if verification
tag is 0 when handling ICMP message.
RFC 4960, Appendix C. ICMP Handling
ICMP6) An implementation MUST validate that the Verification Tag
contained in the ICMP message matches the Verification Tag of the peer.
If the Verification Tag is not 0 and does NOT match, discard the ICMP
message. If it is 0 and the ICMP message contains enough bytes to
verify that the chunk type is an INIT chunk and that the Initiate Tag
matches the tag of the peer, continue with ICMP7. If the ICMP message
is too short or the chunk type or the Initiate Tag does not match,
silently discard the packet.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver rejects a frame in it's ->tx() callback, it must also
stop queues, otherwise mac80211 can go into a loop here. Detect this
situation and abort the loop after five retries, warning about the
driver bug.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
genetlink has a circular locking dependency when dumping the registered
families:
- dump start:
genl_rcv() : take genl_mutex
genl_rcv_msg() : call netlink_dump_start() while holding genl_mutex
netlink_dump_start(),
netlink_dump() : take nlk->cb_mutex
ctrl_dumpfamily() : try to detect this case and not take genl_mutex a
second time
- dump continuance:
netlink_rcv() : call netlink_dump
netlink_dump : take nlk->cb_mutex
ctrl_dumpfamily() : take genl_mutex
Register genl_lock as callback mutex with netlink to fix this. This slightly
widens an already existing module unload race, the genl ops used during the
dump might go away when the module is unloaded. Thomas Graf is working on a
seperate fix for this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max of promiscuity and allmulti plus positive @inc can cause overflow.
Fox example: when allmulti=0xFFFFFFFF, any caller give dev_set_allmulti() a
positive @inc will cause allmulti be off.
This is not what we want, though it's rare case.
The fix is that only negative @inc will cause allmulti or promiscuity be off
and when any caller makes the counters touch the roof, we return error.
Change of v2:
Change void function dev_set_promiscuity/allmulti to return int.
So callers can get the overflow error.
Caller's fix will be done later.
Change of v3:
1. Since we return error to caller, we don't need to print KERN_ERROR,
KERN_WARNING is enough.
2. In dev_set_promiscuity(), if __dev_set_promiscuity() failed, we
return at once.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 608961a5ec.
The problem is that the mac80211 stack not only needs to be able to
muck with the link-level headers, it also might need to mangle all of
the packet data if doing sw wireless encryption.
This fixes kernel bugzilla #10903. Thanks to Didier Raboud (for the
bugzilla report), Andrew Prince (for bisecting), Johannes Berg (for
bringing this bisection analysis to my attention), and Ilpo (for
trying to analyze this purely from the TCP side).
In 2.6.27 we can take another stab at this, by using something like
skb_cow_data() when the TX path of mac80211 ends up with a non-NULL
tx->key. The ESP protocol code in the IPSEC stack can be used as a
model for implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
In net/ipv6/tcp_ipv6.c:
- Remove unneeded tcp_v6_send_check() declaration.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to more easily grep for all things that set
sk->sk_socket, add sk_set_socket() helper inline function.
Suggested (although only half-seriously) by Evgeniy Polyakov.
Signed-off-by: David S. Miller <davem@davemloft.net>
The unix_dgram_sendmsg routine implements a (somewhat crude)
form of receiver-imposed flow control by comparing the length of the
receive queue of the 'peer socket' with the max_ack_backlog value
stored in the corresponding sock structure, either blocking
the thread which caused the send-routine to be called or returning
EAGAIN. This routine is used by both SOCK_DGRAM and SOCK_SEQPACKET
sockets. The poll-implementation for these socket types is
datagram_poll from core/datagram.c. A socket is deemed to be writeable
by this routine when the memory presently consumed by datagrams
owned by it is less than the configured socket send buffer size. This
is always wrong for connected PF_UNIX non-stream sockets when the
abovementioned receive queue is currently considered to be full.
'poll' will then return, indicating that the socket is writeable, but
a subsequent write result in EAGAIN, effectively causing an
(usual) application to 'poll for writeability by repeated send request
with O_NONBLOCK set' until it has consumed its time quantum.
The change below uses a suitably modified variant of the datagram_poll
routines for both type of PF_UNIX sockets, which tests if the
recv-queue of the peer a socket is connected to is presently
considered to be 'full' as part of the 'is this socket
writeable'-checking code. The socket being polled is additionally
put onto the peer_wait wait queue associated with its peer, because the
unix_dgram_sendmsg routine does a wake up on this queue after a
datagram was received and the 'other wakeup call' is done implicitly
as part of skb destruction, meaning, a process blocked in poll
because of a full peer receive queue could otherwise sleep forever
if no datagram owned by its socket was already sitting on this queue.
Among this change is a small (inline) helper routine named
'unix_recvq_full', which consolidates the actual testing code (in three
different places) into a single location.
Signed-off-by: Rainer Weikusat <rweikusat@mssgmbh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tihomir Heidelberg - 9a4gl, reports:
--------------------
I would like to direct you attention to one problem existing in ax.25
kernel since 2.4. If listening socket is closed and its SKB queue is
released but those sockets get weird. Those "unAccepted()" sockets
should be destroyed in ax25_std_heartbeat_expiry, but it will not
happen. And there is also a note about that in ax25_std_timer.c:
/* Magic here: If we listen() and a new link dies before it
is accepted() it isn't 'dead' so doesn't get removed. */
This issue cause ax25d to stop accepting new connections and I had to
restarted ax25d approximately each day and my services were unavailable.
Also netstat -n -l shows invalid source and device for those listening
sockets. It is strange why ax25d's listening socket get weird because of
this issue, but definitely when I solved this bug I do not have problems
with ax25d anymore and my ax25d can run for months without problems.
--------------------
Actually as far as I can see, this problem is even in releases
as far back as 2.2.x as well.
It seems senseless to special case this test on TCP_LISTEN state.
Anything still stuck in state 0 has no external references and
we can just simply kill it off directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments of dev_set_allmulti/promiscuity() is that "While the count in
the device remains above zero...". So negative count is useless.
Fix the type of the counter from "int" to "unsigned int".
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, tun.c running in TUN_TUN_DEV mode will set the protocol of
packet to IPv4 if TUN_NO_PI is set. My program failed to work when I
assumed that the driver will check the first nibble of packet,
determine IP version and set the appropriate protocol.
Signed-off-by: Ang Way Chuang <wcang@nav6.org>
Acked-by: Max Krasnyansky <maxk@qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commits 33c732c361 ([IPV4]: Add raw
drops counter) and a92aa318b4 ([IPV6]:
Add raw drops counter), Wang Chen added raw drops counter for
/proc/net/raw & /proc/net/raw6
This patch adds this capability to UDP sockets too (/proc/net/udp &
/proc/net/udp6).
This means that 'RcvbufErrors' errors found in /proc/net/snmp can be also
be examined for each udp socket.
# grep Udp: /proc/net/snmp
Udp: InDatagrams NoPorts InErrors OutDatagrams RcvbufErrors SndbufErrors
Udp: 23971006 75 899420 16390693 146348 0
# cat /proc/net/udp
sl local_address rem_address st tx_queue rx_queue tr tm->when retrnsmt ---
uid timeout inode ref pointer drops
75: 00000000:02CB 00000000:0000 07 00000000:00000000 00:00000000 00000000 ---
0 0 2358 2 ffff81082a538c80 0
111: 00000000:006F 00000000:0000 07 00000000:00000000 00:00000000 00000000 ---
0 0 2286 2 ffff81042dd35c80 146348
In this example, only port 111 (0x006F) was flooded by messages that
user program could not read fast enough. 146348 messages were lost.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PJ Waskiewicz to the list of maintainers for Intel 10/100/1000/10GbE
adapters.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Permit bonding to function rationally if max_bonds is set to
zero. This will load the module, but create no master devices (which can
be created via sysfs).
Requires some change to bond_create_sysfs; currently, the
netdev sysfs directory is determined from the first bonding device created,
but this is no longer possible. Instead, an interface from net/core is
created to create and destroy files in net_class.
Based on a patch submitted by Phil Oester <kernel@linuxaces.com>.
Modified by Jay Vosburgh to fix the sysfs issue mentioned above and to
update the documentation.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Support for sending multiple gratuitous ARPs during failovers
was added by commit:
commit 7893b2491a
Author: Moni Shoua <monis@voltaire.com>
Date: Sat May 17 21:10:12 2008 -0700
bonding: Send more than one gratuitous ARP when slave takes over
This change modifies that support to remove duplicated code,
add support for ARP monitor (the original only supported miimon), clear
the grat ARP counter in bond_close (lest a later "ifconfig up" immediately
start spewing ARPs), and add documentation for the module parameter.
Also updated driver version to 3.3.0.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
under active-backup mode and when there's actual new_active slave,
have bond_change_active_slave() call the networking core to deliver
NETDEV_BONDING_FAILOVER event such that the fail-over can be notable
by code outside of the bonding driver such as the RDMA stack and
monitoring tools.
As the correct context of locking appropriate for notifier calls is RTNL
and nothing else, bond->curr_slave_lock and bond->lock are unlocked and
later locked again. This is ensured by the rest of the code to be safe
under backup-mode AND when new_active is not NULL.
Jay Vosburgh modified the original patch for formatting and fixed a
compiler error.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
simplified the code of bond_change_active_slave() such that under
active-backup mode there's one "if (new_active)" test and the rest
of the code only does extra checks on top of it. This removed an
unneeded "if (bond->send_grat_arp > 0)" check and avoid calling
bond_send_gratuitous_arp when there's no active slave.
Jay Vosburgh made minor coding style changes to the orignal patch.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add NETDEV_BONDING_FAILOVER event to be used in a successive patch
by bonding to announce fail-over for the active-backup mode through the
netdev events notifier chain mechanism. Such an event can be of use for the
RDMA CM (communication manager) to let native RDMA ULPs (eg NFS-RDMA, iSER)
always be aligned with the IP stack, in the sense that they use the same
ports/links as the stack does. More usages can be done to allow monitoring
tools based on netlink events being aware to bonding fail-over.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for Yukon 2 Ultra 2 chip set (88E8057) based on code in latest
version of vendor driver (sk98lin 10.60.2.3). Untested on real hardware.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PCI device table can be marked as devinitconst by using macro.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change how chip version is printed so that if an unknown version is detected
nothing breaks.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Change the setup of the PHY registers on some chip ids. These changes
make the latest sky2 driver follow the vendor driver.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The arch/ppc sub-tree has been removed in the powerpc git tree. The old
ibm_emac driver is no longer used by anything as a result of this. This
removes it, leaving the ibm_newemac driver as the proper driver to use for
PowerPC boards with the EMAC hardware.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The atl1 driver tries to determine the MAC address thusly:
- If an EEPROM exists, read the MAC address from EEPROM and
validate it.
- If an EEPROM doesn't exist, try to read a MAC address from
SPI flash.
- If that fails, try to read a MAC address directly from the
MAC Station Address register.
- If that fails, assign a random MAC address provided by the
kernel.
We now have a report of a system fitted with an EEPROM containing all
zeros where we expect the MAC address to be, and we currently handle
this as an error condition. Turns out, on this system the BIOS writes
a valid MAC address to the NIC's MAC Station Address register, but we
never try to read it because we return an error when we find the all-
zeros address in EEPROM.
This patch relaxes the error check and continues looking for a MAC
address even if it finds an illegal one in EEPROM.
Signed-off-by: Radu Cristescu <advantis@gmx.net>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Keep enc28j60 chips in low-power mode when they're not in use.
At typically 120 mA, these chips run hot even when idle; this
low power mode cuts that power usage by a factor of around 100.
This version provides a generic routine to poll a register until
its masked value equals some value ... e.g. bit set or cleared.
It's basically what the previous wait_phy_ready() did, but this
version is generalized to support the handshaking needed to
enter and exit low power mode.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Minor bugfixes to the enc28j60 driver ... wrong section marking,
indentation, and bogus use of spi_bus_type.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Downloading firmware in pci probe allows recovery in case of
firmware failure by reloading the driver.
Also reduced delays in firmware load.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
o Remove unnecessary debug prints and functions.
o Explicitly specify pci class (0x020000) to avoid enabling
management function.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Store physical port number in netxen_adapter structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes a the issue where logical port number is set incorrectly
for HP blade mezz cards.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ibm_newemac driver requires ether_crc to be defined. Apparently it is
possible to generate a .config without CONFIG_CRC32 set which causes the
following link errors if IBM_NEW_EMAC is selected:
LD .tmp_vmlinux1
drivers/built-in.o: In function `emac_hash_mc':
core.c:(.text+0x2f524): undefined reference to `crc32_le'
core.c:(.text+0x2f528): undefined reference to `bitrev32'
make: *** [.tmp_vmlinux1] Error 1
This patch has IBM_NEW_EMAC select CRC32 so we don't hit this error.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ROSE network is organized through nodes connected via hamradio or Internet.
AX25 packet radio frames sent to a remote ROSE address destination are routed
through these nodes.
Without the present patch, automatic routing mechanism did not work optimally
due to an improper parameter checking.
rose_get_neigh() function is called either by rose_connect() or by
rose_route_frame().
In the case of a call from rose_connect(), f0 timer is checked to find if a connection
is already pending. In that case it returns the address of the neighbour, or returns a NULL otherwise.
When called by rose_route_frame() the purpose was to route a packet AX25 frame
through an adjacent node given a destination rose address.
However, in that case, t0 timer checked does not indicate if the adjacent node
is actually connected even if the timer is not null. Thus, for each frame sent, the
function often tried to start a new connexion even if the adjacent node was already connected.
The patch adds a "new" parameter that is true when the function is called by
rose route_frame().
This instructs rose_get_neigh() to check node parameter "restarted".
If restarted is true it means that the route to the destination address is opened via a neighbour
node already connected.
If "restarted" is false the function returns a NULL.
In that case the calling function will initiate a new connection as before.
This results in a fast routing of frames, from nodes to nodes, until
destination is reached, as originaly specified by ROSE protocole.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When generating the ip header for the transformed packet we just copy
the frag_off field of the ip header from the original packet to the ip
header of the new generated packet. If we receive a packet as a chain
of fragments, all but the last of the new generated packets have the
IP_MF flag set. We have to mask the frag_off field to only keep the
IP_DF flag from the original packet. This got lost with git commit
36cf9acf93 ("[IPSEC]: Separate
inner/outer mode processing on output")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the most obvious 64-bit problems, but it is still very very
broken in other aspects.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bridge netfilter code so that it uses CONFIG_IPV6 as needed:
net/built-in.o: In function `ebt_filter_ip6':
ebt_ip6.c:(.text+0x87c37): undefined reference to `ipv6_skip_exthdr'
net/built-in.o: In function `ebt_log_packet':
ebt_log.c:(.text+0x88dee): undefined reference to `ipv6_skip_exthdr'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally, the bridge just chooses the smallest mac address as the
bridge id and mac address of bridge device. But if the administrator
has explictly set the interface address then don't change it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any frame addressed to link-local addresses should be processed by local
receive path. The earlier code would process them only if STP was enabled.
Since there are other frames like LACP for bonding, we should always
process them.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings
Vlad Yasevich
Wei Yongjun
David S. Miller
Johannes Berg
Patrick McHardy
Wang Chen
Rami Rosen
Rainer Weikusat
Ang Way Chuang
Eric Dumazet
Jeff Kirsher
Jay Vosburgh
Or Gerlitz
Stephen Hemminger
Josh Boyer
Jeff Garzik
Radu Cristescu
David Brownell
Dhananjay Phadke
Bernard Pidoux
Steffen Klassert
Chas Williams
Alan Cox
Mitchell Blank Jr
Jorge Boncompte [DTI2]
Randy Dunlap