In case timers are not in sync when cpus start (i.e. hot plug / offset
resets) we need to synchronize the secondary cpus internal timer with
the main cpu. This is needed as in OpenRISC SMP there is only one
clocksource registered which reads from the same ttcr register on each
cpu.
This synchronization routine heavily borrows from mips implementation that
does something similar.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Lockdep is needed for proving the spinlocks and rwlocks work fine on our
platform. It also requires calling the trace_hardirqs_off() and
trace_hardirqs_on() pair of routines when entering and exiting an
interrupt.
For OpenRISC the interrupt stack frame does not support frame pointers,
so to call trace_hardirqs_on() and trace_hardirqs_off() here the macro's
build up a stack frame each time.
There is one necessary small change in _sys_call_handler to move
interrupt enabling later so they can get re-enabled during syscall
restart. This was done to fix lockdep warnings that are now possible due
to this
patch.
Signed-off-by: Stafford Horne <shorne@gmail.com>
For lockdep support a reliable stack trace mechanism is needed. This
patch adds support in OpenRISC for the stacktrace framework, implemented
by a simple unwinder api. The unwinder api supports both framepointer
and basic stack tracing.
The unwinder is now used to replace the stack_dump() implementation as
well. The new traces are inline with other architectures trace format:
Call trace:
[<c0004448>] show_stack+0x3c/0x58
[<c031c940>] dump_stack+0xa8/0xe4
[<c0008104>] __cpu_up+0x64/0x130
[<c000d268>] bringup_cpu+0x3c/0x178
[<c000d038>] cpuhp_invoke_callback+0xa8/0x1fc
[<c000d680>] cpuhp_up_callbacks+0x44/0x14c
[<c000e400>] cpu_up+0x14c/0x1bc
[<c041da60>] smp_init+0x104/0x15c
[<c033843c>] ? kernel_init+0x0/0x140
[<c0415e04>] kernel_init_freeable+0xbc/0x25c
[<c033843c>] ? kernel_init+0x0/0x140
[<c0338458>] kernel_init+0x1c/0x140
[<c003a174>] ? schedule_tail+0x18/0xa0
[<c0006b80>] ret_from_fork+0x1c/0x9c
Signed-off-by: Stafford Horne <shorne@gmail.com>
On OpenRISC the icache does not snoop data stores. This can cause
aliasing as reported by Jan. This patch fixes the issue to ensure icache
is properly synchronized when code is written to memory. It supports both
SMP and UP flushing.
This supports dcache flush as well for architectures that do not support
write-through caches; most OpenRISC implementations do implement
write-through cache however. Dcache flushes are done only on a single
core as OpenRISC dcaches all support snooping of bus stores.
Signed-off-by: Jan Henrik Weinstock <jan.weinstock@ice.rwth-aachen.de>
[shorne@gmail.com: Squashed patches and wrote commit message]
Signed-off-by: Stafford Horne <shorne@gmail.com>
Currently we do a spin on secondary cpus when waiting to boot. This
theoretically causes issues with power consumption and does cause issues
with qemu cycle burning (it starves cpu 0 from actually being able to
boot.)
This change puts each secondary cpu to sleep if they have a power
management unit, then signals them to wake via IPI when its time to boot.
If the cpus have no power management unit they will loop as before.
Note: The wakeup IPI requires a special interrupt handler as on secondary
cpu's the interrupt infrastructure is not yet established. This
interrupt handler is set and reset by updating SPR_EVBAR.
Signed-off-by: Stafford Horne <shorne@gmail.com>
During SMP testing we were getting the below warning after booting the
secondary cpu:
[ 0.060000] BUG: scheduling while atomic: swapper/1/0/0x00000000
This change follows similar patterns from other architectures to start
the schduler with preempt disabled.
Signed-off-by: Stafford Horne <shorne@gmail.com>
This patch introduces the SMP support for the OpenRISC architecture.
The SMP architecture requires cores which have multi-core features which
have been introduced a few years back including:
- New SPRS SPR_COREID SPR_NUMCORES
- Shadow SPRs
- Atomic Instructions
- Cache Coherency
- A wired in IPI controller
This patch adds all of the SMP specific changes to core infrastructure,
it looks big but it needs to go all together as its hard to split this
one up.
Boot loader spinning of second cpu is not supported yet, it's assumed
that Linux is booted straight after cpu reset.
The bulk of these changes are trivial changes to refactor to use per cpu
data structures throughout. The addition of the smp.c and changes in
time.c are the changes. Some specific notes:
MM changes
----------
The reason why this is created as an array, and not with DEFINE_PER_CPU
is that doing it this way, we'll save a load in the tlb-miss handler
(the load from __per_cpu_offset).
TLB Flush
---------
The SMP implementation of flush_tlb_* works by sending out a
function-call IPI to all the non-local cpus by using the generic
on_each_cpu() function.
Currently, all flush_tlb_* functions will result in a flush_tlb_all(),
which has always been the behaviour in the UP case.
CPU INFO
--------
This creates a per cpu cpuinfo struct and fills it out accordingly for
each activated cpu. show_cpuinfo is also updated to reflect new version
information in later versions of the spec.
SMP API
-------
This imitates the arm64 implementation by having a smp_cross_call
callback that can be set by set_smp_cross_call to initiate an IPI and a
handle_IPI function that is expected to be called from an IPI irqchip
driver.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: added cpu stop, checkpatch fixes, wrote commit message]
Signed-off-by: Stafford Horne <shorne@gmail.com>
Previously, the area between 0x0-0x100 have been used as a "scratch"
memory area to temporarily store regs during exception entry. In a
multi-core environment, this will not work.
This change is to use shadow registers for nested context.
Currently only the "critical" temp load/stores are covered, the
EMERGENCY_PRINT ones are left as is (when they are used, it's game over
anyway), they need to be handled as well in the future.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=aihT
-----END PGP SIGNATURE-----
Merge tag 'openrisc-for-linus' of git://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne:
"Openrisc fixes for this 4.13 merge window, there is not really much
here:
- include cleanups, one with should reduce build time slightly
- switch to new toolchain to new (>2 year old) toolchain prefix"
* tag 'openrisc-for-linus' of git://github.com/openrisc/linux:
openrisc: defconfig: Cleanup from old Kconfig options
openrisc: explicitly include linux/bug.h in asm/fixmap.h
openrisc: Switch to use export.h instead of module.h
openrisc: Change toolchain from or32- to or1k-
The only user of thread_saved_pc() in non-arch-specific code was removed
in commit 8243d55977 ("sched/core: Remove pointless printout in
sched_show_task()"). Remove the implementations as well.
Some architectures use thread_saved_pc() in their arch-specific code.
Leave their thread_saved_pc() intact.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a regression in commit 4d6501dce0 where I didn't notice
that MIPS and OpenRISC were reinitialising p->{set,clear}_child_tid to
NULL after our initialisation in copy_process().
We can simply get rid of the arch-specific initialisation here since it
is now always done in copy_process() before hitting copy_thread{,_tls}().
Review notes:
- As far as I can tell, copy_process() is the only user of
copy_thread_tls(), which is the only caller of copy_thread() for
architectures that don't implement copy_thread_tls().
- After this patch, there is no arch-specific code touching
p->set_child_tid or p->clear_child_tid whatsoever.
- It may look like MIPS/OpenRISC wanted to always have these fields be
NULL, but that's not true, as copy_process() would unconditionally
set them again _after_ calling copy_thread_tls() before commit
4d6501dce0.
Fixes: 4d6501dce0 ("kthread: Fix use-after-free if kthread fork fails")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net> # MIPS only
Acked-by: Stafford Horne <shorne@gmail.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: openrisc@lists.librecores.org
Cc: Jamie Iles <jamie.iles@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce dependencies on module.h since all we need here is export.h
for EXPORT_SYMBOL.
Fixes: f50169324d ("module.h: split out the EXPORT_SYMBOL into export.h")
Signed-off-by: Stafford Horne <shorne@gmail.com>
But first update the usage sites with the new header dependency.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task_stack.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task_stack.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/debug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/debug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix typos and add the following to the scripts/spelling.txt:
efective||effective
While we are here, fix the "addres" as well in the touched line in
arch/openrisc/kernel/entry.S.
Link: http://lkml.kernel.org/r/1481573103-11329-10-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
aligment||alignment
I did not touch the "N_BYTE_ALIGMENT" macro in
drivers/net/wireless/realtek/rtlwifi/wifi.h to avoid unpredictable
impact.
I fixed "_aligment_handler" in arch/openrisc/kernel/entry.S because
it is surrounded by #if 0 ... #endif. It is surely safe and I
confirmed "_alignment_handler" is correct.
I also fixed the "controler" I found in the same hunk in
arch/openrisc/kernel/head.S.
Link: http://lkml.kernel.org/r/1481573103-11329-8-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
-----BEGIN PGP SIGNATURE-----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=wmBO
-----END PGP SIGNATURE-----
Merge tag 'openrisc-for-linus' of git://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne:
"Highlights include:
- optimized memset and memcpy routines, ~20% boot time saving
- support for cpu idling
- adding support for l.swa and l.lwa atomic operations (in spec from
2014)
- use atomics to implement: bitops, cmpxchg, futex
- the atomics are in preparation for SMP support"
* tag 'openrisc-for-linus' of git://github.com/openrisc/linux: (25 commits)
openrisc: head: Init r0 to 0 on start
openrisc: Export ioremap symbols used by modules
arch/openrisc/lib/memcpy.c: use correct OR1200 option
openrisc: head: Remove unused strings
openrisc: head: Move init strings to rodata section
openrisc: entry: Fix delay slot detection
openrisc: entry: Whitespace and comment cleanups
scripts/checkstack.pl: Add openrisc support
MAINTAINERS: Add the openrisc official repository
openrisc: Add .gitignore
openrisc: Add optimized memcpy routine
openrisc: Add optimized memset
openrisc: Initial support for the idle state
openrisc: Fix the bitmask for the unit present register
openrisc: remove unnecessary stddef.h include
openrisc: add futex_atomic_* implementations
openrisc: add optimized atomic operations
openrisc: add cmpxchg and xchg implementations
openrisc: add atomic bitops
openrisc: add l.lwa/l.swa emulation
...
Originally openrisc spec 0 specified that r0 would be wired to ground.
This is no longer the case. r0 is not guaranteed to be 0 at init, so we
need to initialize it to 0 before using it.
Also, if we are clearing r0 we cant use r0 to clear itself. Change the
the CLEAR_GPR macro to use movhi for clearing.
Reported-by: Jakob Viketoft <jakob.viketoft@aacmicrotec.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
These string definitions are no longer used removed them. Noticed this
while working on a CONFIG_DEBUG_INFO build issue.
Signed-off-by: Stafford Horne <shorne@gmail.com>
The strings used during the head/init phase of openrisc bootup were
stored in the executable section of the binary.
This causes compilation to fail when using CONFIG_DEBUG_INFO with
error:
Error: unaligned opcodes detected in executable segment
Signed-off-by: Stafford Horne <shorne@gmail.com>
Use execption SR stored in pt_regs for detection, the current SR is not
correct as the handler is running after return from exception.
Also, The code that checks for a delay slot uses a flag bitmask and then
wants to check if the result is not zero. The test it implemented was
wrong.
Correct it by changing the test to check result against non zero.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Cleanups to whitespace and add some comments. Reading through the delay
slot logic I noticed some things:
- Delay slot instructions were not indented
- Some comments are not lined up
- Use tabs and spaces consistent with other code
No functional change
Signed-off-by: Stafford Horne <shorne@gmail.com>
This adds a hand-optimized assembler version of memset and sets
__HAVE_ARCH_MEMSET to use this version instead of the generic C
routine
Signed-off-by: Olof Kindgren <olof.kindgren@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
This patch adds basic support for the idle state of the cpu.
The patch overrides the regular idle function, enables the interupts,
checks for the power management unit and enables the cpu doze mode
if available.
Signed-off-by: Sebastian Macke <sebastian@macke.de>
[shorne@gmail.com: Fixed checkpatch, blankline after declarations]
Signed-off-by: Stafford Horne <shorne@gmail.com>
This adds an emulation layer for implementations
that lack the l.lwa and l.swa instructions.
It handles these instructions both in kernel space and
user space.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: Added delay slot pc adjust logic]
Signed-off-by: Stafford Horne <shorne@gmail.com>
This brings it inline with the other setup oprations done like the cache
enables _ic_enable and _dc_enable. Also, this is going to make it
easier to initialize additional cpu's when smp is introduced.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: Added commit body]
Signed-off-by: Stafford Horne <shorne@gmail.com>
The stack size was hard coded to 0x2000, use the standard THREAD_SIZE
definition loaded from thread_info.h.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: Added body to the commit message]
Signed-off-by: Stafford Horne <shorne@gmail.com>
By slightly reorganizing the code, the number of registers
used in the tlb miss handlers can be reduced by two,
thus removing the need to save them to memory.
Also, some dead and commented out code is removed.
No functional change.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Motivation for this is to be able to print the way information
properly in print_cpuinfo(), instead of hardcoding it to one.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
[shorne@gmail.com fixed conflict with show_cpuinfo change]
Signed-off-by: Stafford Horne <shorne@gmail.com>
These files were only including module.h for exception table related
functions. We've now separated that content out into its own file
"extable.h" so now move over to that and avoid all the extra header
content in module.h that we don't really need to compile these files.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Stafford Horne <shorne@gmail.com>
Cc: openrisc@lists.librecores.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The build robot reports:
.tmp_kallsyms1.o: In function `kallsyms_relative_base':
>> (.rodata+0x8a18): undefined reference to `_text'
This is when using 'make alldefconfig'. Adding this _text symbol to mark
the start of the kernel as in other architecture fixes this.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Acked-by: Jonas Bonn <jonas@southpole.se>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change allows us to pass DMA_ATTR_SKIP_CPU_SYNC which allows us to
avoid invoking cache line invalidation if the driver will just handle it
via a sync_for_cpu or sync_for_device call.
Link: http://lkml.kernel.org/r/20161110113524.76501.87966.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During page fault handling we check the last instruction to understand
if the fault was for a read or for a write. By default we fall back to
read. New instructions were added to the openrisc 1.1 spec for an
atomic load/store pair (l.lwa/l.swa).
This patch adds the opcode for l.swa (0x33) allowing it to be treated as
a write operation.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: expanded a bit on the comment]
Signed-off-by: Stafford Horne <shorne@gmail.com>
The openrisc.net domain expired and was taken over by squatters.
These updates point documentation to the new domain, mailing lists
and git repos.
Also, Jonas is not the main maintainer anylonger, he reviews changes
but does not maintain a repo or sent pull requests. Updating this to
add Stafford and Stefan who are the active maintainers.
Acked-by: Olof Kindgren <olof.kindgren@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Clearing out one todo item. Use the memblock boot time memory
which is the current standard.
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jonas <jonas@southpole.se>
Signed-off-by: Stafford Horne <shorne@gmail.com>
The of_platform_populate call in the openrisc arch code is now redundant
as the DT core provides a default call. Openrisc has a NULL match table
which means only top level nodes with compatible strings will have
devices creates. The default version will also descend nodes in the
match table such as "simple-bus" which should be fine as openrisc
doesn't have any of these (though it is preferred that memory-mapped
peripherals be grouped under a bus node(s)).
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jonas Bonn <jonas@southpole.se>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Stafford Horne <shorne@gmail.com>
The output file format for or1k has changed from "elf32-or32"
to "elf32-or1k". Select the correct output format automatically
to be able to compile the kernel with both toolchain variants.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Historically OpenRISC GCC has reserved r10 which we now use to hold
the thread pointer for thread-local storage (TLS).
Signed-off-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Fix signal handling for when signals are handled as the result of timers
or exceptions, previous code assumed syscalls. This was noticeable with X
crashing where it uses SIGALRM.
This patch restores all regs before returning to userspace via
_resume_userspace instead of via syscall return path.
The rt_sigreturn syscall is more like a context switch than a function
call; it entails a return from one context (the signal handler) to another
(the process in question). For a context switch like this there are
effectively no call-saved regs that remain constant across the transition.
Reported-by: Sebastian Macke <sebastian@macke.de>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Tested-by: Guenter Roeck <linux@roeck-us.net>
[shorne@gmail.com: Updated comment better reflect change and issue]
Signed-off-by: Stafford Horne <shorne@gmail.com>
When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative. Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".
We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.
This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.
Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KASAN needs to know whether the allocation happens in an IRQ handler.
This lets us strip everything below the IRQ entry point to reduce the
number of unique stack traces needed to be stored.
Move the definition of __irq_entry to <linux/interrupt.h> so that the
users don't need to pull in <linux/ftrace.h>. Also introduce the
__softirq_entry macro which is similar to __irq_entry, but puts the
corresponding functions to the .softirqentry.text section.
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Migrate openrisc driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
We weren't doing anything in the ->set_mode() callback. So, this patch
doesn't provide any set-state callbacks.
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Merge second patchbomb from Andrew Morton:
- the rest of MM
- various misc bits
- add ability to run /sbin/reboot at reboot time
- printk/vsprintf changes
- fiddle with seq_printf() return value
* akpm: (114 commits)
parisc: remove use of seq_printf return value
lru_cache: remove use of seq_printf return value
tracing: remove use of seq_printf return value
cgroup: remove use of seq_printf return value
proc: remove use of seq_printf return value
s390: remove use of seq_printf return value
cris fasttimer: remove use of seq_printf return value
cris: remove use of seq_printf return value
openrisc: remove use of seq_printf return value
ARM: plat-pxa: remove use of seq_printf return value
nios2: cpuinfo: remove use of seq_printf return value
microblaze: mb: remove use of seq_printf return value
ipc: remove use of seq_printf return value
rtc: remove use of seq_printf return value
power: wakeup: remove use of seq_printf return value
x86: mtrr: if: remove use of seq_printf return value
linux/bitmap.h: improve BITMAP_{LAST,FIRST}_WORD_MASK
MAINTAINERS: CREDITS: remove Stefano Brivio from B43
.mailmap: add Ricardo Ribalda
CREDITS: add Ricardo Ribalda Delgado
...
The seq_printf return value, because it's frequently misused,
will eventually be converted to void.
See: commit 1f33c41c03 ("seq_file: Rename seq_overflow() to
seq_has_overflowed() and make public")
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull exec domain removal from Richard Weinberger:
"This series removes execution domain support from Linux.
The idea behind exec domains was to support different ABIs. The
feature was never complete nor stable. Let's rip it out and make the
kernel signal handling code less complicated"
* 'exec_domain_rip_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (27 commits)
arm64: Removed unused variable
sparc: Fix execution domain removal
Remove rest of exec domains.
arch: Remove exec_domain from remaining archs
arc: Remove signal translation and exec_domain
xtensa: Remove signal translation and exec_domain
xtensa: Autogenerate offsets in struct thread_info
x86: Remove signal translation and exec_domain
unicore32: Remove signal translation and exec_domain
um: Remove signal translation and exec_domain
tile: Remove signal translation and exec_domain
sparc: Remove signal translation and exec_domain
sh: Remove signal translation and exec_domain
s390: Remove signal translation and exec_domain
mn10300: Remove signal translation and exec_domain
microblaze: Remove signal translation and exec_domain
m68k: Remove signal translation and exec_domain
m32r: Remove signal translation and exec_domain
m32r: Autogenerate offsets in struct thread_info
frv: Remove signal translation and exec_domain
...
flush_old_exec() has already done that. Back on 2011 a bunch of
instances like that had been kicked out, but that hadn't taken
care of then-out-of-tree architectures, obviously, and they served
as reinfection vector...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If an attacker can cause a controlled kernel stack overflow, overwriting
the restart block is a very juicy exploit target. This is because the
restart_block is held in the same memory allocation as the kernel stack.
Moving the restart block to struct task_struct prevents this exploit by
making the restart_block harder to locate.
Note that there are other fields in thread_info that are also easy
targets, at least on some architectures.
It's also a decent simplification, since the restart code is more or less
identical on all architectures.
[james.hogan@imgtec.com: metag: align thread_info::supervisor_stack]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
The openrisc irqchip driver has been converted to handle_domain_irq,
making it possible to remove the handle_IRQ stub entierely.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Link: https://lkml.kernel.org/r/1409047421-27649-27-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to limit code duplication, convert the architecture specific
handle_IRQ to use the generic __handle_domain_irq function.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Link: https://lkml.kernel.org/r/1409047421-27649-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull arch signal handling cleanup from Richard Weinberger:
"This patch series moves all remaining archs to the get_signal(),
signal_setup_done() and sigsp() functions.
Currently these archs use open coded variants of the said functions.
Further, unused parameters get removed from get_signal_to_deliver(),
tracehook_signal_handler() and signal_delivered().
At the end of the day we save around 500 lines of code."
* 'signal-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (43 commits)
powerpc: Use sigsp()
openrisc: Use sigsp()
mn10300: Use sigsp()
mips: Use sigsp()
microblaze: Use sigsp()
metag: Use sigsp()
m68k: Use sigsp()
m32r: Use sigsp()
hexagon: Use sigsp()
frv: Use sigsp()
cris: Use sigsp()
c6x: Use sigsp()
blackfin: Use sigsp()
avr32: Use sigsp()
arm64: Use sigsp()
arc: Use sigsp()
sas_ss_flags: Remove nested ternary if
Rip out get_signal_to_deliver()
Clean up signal_delivered()
tracehook_signal_handler: Remove sig, info, ka and regs
...
In addition to consolidating the or1k-pic with other interrupt
controllers, this makes OpenRISC less tied to its on-cpu
interrupt controller.
All or1k-pic specific parts are moved out of irq.c and into
drivers/irqchip/irq-or1k-pic.c
In that transition, the functionality have been divided into
three chip variants.
One that handles level triggered interrupts, one that handles edge
triggered interrupts and one that handles the interrupt
controller that is present in the or1200 OpenRISC cpu
implementation.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Link: https://lkml.kernel.org/r/1401136302-27654-1-git-send-email-stefan.kristiansson@saunalahti.fi
Acked-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Unify the various architectures __dtb_start and __dtb_end definitions
moving them into of_fdt.h.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-metag@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux@lists.openrisc.net
Cc: linux-xtensa@linux-xtensa.org
Tested-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Stephen Chivers <schivers@csc.com>
Use the more generic functions get_signal() signal_setup_done()
for signal delivery.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
The mainline signal handling code for OpenRISC has been buggy since day
one with respect to syscall restart. This patch significantly reworks
the signal handling code:
i) Move the "work pending" loop to C code (borrowed from ARM arch)
ii) Allow a tracer to muck about with the IP and skip syscall restart
in that case (again, borrowed from ARM)
iii) Make signal handling WRT syscall restart actually work
v) Make the signal handling code look more like that of other
architectures so that it's easier for others to follow
Reported-by: Anders Nystrom <anders@southpole.se>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
- small cleanups to make allmodconfig pass
- defconfig refresh
- a handful of code sanitization patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlKF9WkACgkQ70gcjN2673NUSQCffUNqhw74yO4K8E+2CNVwmwNF
uIoAniqV3CoCGJ1jioMx0YGLWwsAWJay
=EvE1
-----END PGP SIGNATURE-----
Merge tag 'for-3.13' of git://git.openrisc.net/~jonas/linux
Pull OpenRISC updates from Jonas Bonn:
- small cleanups to make allmodconfig pass
- defconfig refresh
- a handful of code sanitization patches
* tag 'for-3.13' of git://git.openrisc.net/~jonas/linux:
openrisc: Refactor or32_early_setup()
openrisc: Remove unused declaration of __initramfs_start
openrisc: Use the declarations provided by <asm/sections.h>
openrisc: Refresh or1ksim_defconfig for v3.12
openrisc: Refactor 16-bit constant relocation
openrisc: include: asm: Kbuild: add default "vga.h"
openrisc: Makefile: append "-D__linux__" to KBUILD_CFLAGS
- Change fdt pointer (passed from head.S) from unsigned int to void *,
which allows to kill a cast, and makes it compatible with __dtb_start.
- Use pr_info(),
- Extract common part.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux@lists.openrisc.net
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Openrisc's private vmlinux.h duplicates a few definitions that are already
provided by asm-generic/sections.h. The former is used by setup.c only,
while the latter is already used everywhere else.
Convert setup.c to use the generic version:
- Include <asm/sections.h>,
- Remove the (slightly different) extern declarations,
- Remove the no longer needed address-of ('&') operators.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
arch/openrisc/kernel/module.c: In function 'apply_relocate_add':
arch/openrisc/kernel/module.c:50:13: warning: assignment from incompatible pointer type
arch/openrisc/kernel/module.c:54:13: warning: assignment from incompatible pointer type
Move the pointer increments to the dereference statements to avoid
incompatible pointer assignments, and remove superfluous casts.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
It appears openrisc prom.c was just copied from another arch with a
bunch of unnecessary includes. Remove all the unecessary ones.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
All arches do essentially the same thing now for
early_init_dt_setup_initrd_arch, so it can now be removed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Create a weak version of early_init_dt_add_memory_arch which uses
memblock. This will unify all architectures except ones with custom
memory bank structs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Jonas Bonn <jonas@southpole.se>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: linux@lists.openrisc.net
Cc: devicetree@vger.kernel.org
Convert openrisc to use new early_init_dt_scan function.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Use the common unflatten_and_copy_device_tree to copy the built-in FDT
out of init section. This moves the copy later in the boot, but there
do not appear to be any references to strings in the FDT before the copy.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Save some pointless copying of the kernel command line and just use
boot_command_line instead. The DT code already handles CONFIG_CMDLINE,
so a separate copy is not needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Most architectures use the same implementation. Collapse the common ones
into a single weak function that can be overridden.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
On some PAE architectures, the entire range of physical memory could reside
outside the 32-bit limit. These systems need the ability to specify the
initrd location using 64-bit numbers.
This patch globally modifies the early_init_dt_setup_initrd_arch() function to
use 64-bit numbers instead of the current unsigned long.
There has been quite a bit of debate about whether to use u64 or phys_addr_t.
It was concluded to stick to u64 to be consistent with rest of the device
tree code. As summarized by Geert, "The address to load the initrd is decided
by the bootloader/user and set at that point later in time. The dtb should not
be tied to the kernel you are booting"
More details on the discussion can be found here:
https://lkml.org/lkml/2013/6/20/690https://lkml.org/lkml/2012/9/13/544
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/openrisc uses of the __cpuinit macros from
all C files. Currently openrisc does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Jonas Bonn <jonas@southpole.se>
Cc: linux@lists.openrisc.net
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
show_regs() is inherently arch-dependent but it does make sense to print
generic debug information and some archs already do albeit in slightly
different forms. This patch introduces a generic function to print debug
information from show_regs() so that different archs print out the same
information and it's much easier to modify what's printed.
show_regs_print_info() prints out the same debug info as dump_stack()
does plus task and thread_info pointers.
* Archs which didn't print debug info now do.
alpha, arc, blackfin, c6x, cris, frv, h8300, hexagon, ia64, m32r,
metag, microblaze, mn10300, openrisc, parisc, score, sh64, sparc,
um, xtensa
* Already prints debug info. Replaced with show_regs_print_info().
The printed information is superset of what used to be there.
arm, arm64, avr32, mips, powerpc, sh32, tile, unicore32, x86
* s390 is special in that it used to print arch-specific information
along with generic debug info. Heiko and Martin think that the
arch-specific extra isn't worth keeping s390 specfic implementation.
Converted to use the generic version.
Note that now all archs print the debug info before actual register
dumps.
An example BUG() dump follows.
kernel BUG at /work/os/work/kernel/workqueue.c:4841!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #7
Hardware name: empty empty/S3992, BIOS 080011 10/26/2007
task: ffff88007c85e040 ti: ffff88007c860000 task.ti: ffff88007c860000
RIP: 0010:[<ffffffff8234a07e>] [<ffffffff8234a07e>] init_workqueues+0x4/0x6
RSP: 0000:ffff88007c861ec8 EFLAGS: 00010246
RAX: ffff88007c861fd8 RBX: ffffffff824466a8 RCX: 0000000000000001
RDX: 0000000000000046 RSI: 0000000000000001 RDI: ffffffff8234a07a
RBP: ffff88007c861ec8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff8234a07a
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff88015f7ff000 CR3: 00000000021f1000 CR4: 00000000000007f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff88007c861ef8 ffffffff81000312 ffffffff824466a8 ffff88007c85e650
0000000000000003 0000000000000000 ffff88007c861f38 ffffffff82335e5d
ffff88007c862080 ffffffff8223d8c0 ffff88007c862080 ffffffff81c47760
Call Trace:
[<ffffffff81000312>] do_one_initcall+0x122/0x170
[<ffffffff82335e5d>] kernel_init_freeable+0x9b/0x1c8
[<ffffffff81c47760>] ? rest_init+0x140/0x140
[<ffffffff81c4776e>] kernel_init+0xe/0xf0
[<ffffffff81c6be9c>] ret_from_fork+0x7c/0xb0
[<ffffffff81c47760>] ? rest_init+0x140/0x140
...
v2: Typo fix in x86-32.
v3: CPU number dropped from show_regs_print_info() as
dump_stack_print_info() has been updated to print it. s390
specific implementation dropped as requested by s390 maintainers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile bits]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both dump_stack() and show_stack() are currently implemented by each
architecture. show_stack(NULL, NULL) dumps the backtrace for the
current task as does dump_stack(). On some archs, dump_stack() prints
extra information - pid, utsname and so on - in addition to the
backtrace while the two are identical on other archs.
The usages in arch-independent code of the two functions indicate
show_stack(NULL, NULL) should print out bare backtrace while
dump_stack() is used for debugging purposes when something went wrong,
so it does make sense to print additional information on the task which
triggered dump_stack().
There's no reason to require archs to implement two separate but mostly
identical functions. It leads to unnecessary subtle information.
This patch expands the dummy fallback dump_stack() implementation in
lib/dump_stack.c such that it prints out debug information (taken from
x86) and invokes show_stack(NULL, NULL) and drops arch-specific
dump_stack() implementations in all archs except blackfin. Blackfin's
dump_stack() does something wonky that I don't understand.
Debug information can be printed separately by calling
dump_stack_print_info() so that arch-specific dump_stack()
implementation can still emit the same debug information. This is used
in blackfin.
This patch brings the following behavior changes.
* On some archs, an extra level in backtrace for show_stack() could be
printed. This is because the top frame was determined in
dump_stack() on those archs while generic dump_stack() can't do that
reliably. It can be compensated by inlining dump_stack() but not
sure whether that'd be necessary.
* Most archs didn't use to print debug info on dump_stack(). They do
now.
An example WARN dump follows.
WARNING: at kernel/workqueue.c:4841 init_workqueues+0x35/0x505()
Hardware name: empty
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #9
0000000000000009 ffff88007c861e08 ffffffff81c614dc ffff88007c861e48
ffffffff8108f50f ffffffff82228240 0000000000000040 ffffffff8234a03c
0000000000000000 0000000000000000 0000000000000000 ffff88007c861e58
Call Trace:
[<ffffffff81c614dc>] dump_stack+0x19/0x1b
[<ffffffff8108f50f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8108f56a>] warn_slowpath_null+0x1a/0x20
[<ffffffff8234a071>] init_workqueues+0x35/0x505
...
v2: CPU number added to the generic debug info as requested by s390
folks and dropped the s390 specific dump_stack(). This loses %ksp
from the debug message which the maintainers think isn't important
enough to keep the s390-specific dump_stack() implementation.
dump_stack_print_info() is moved to kernel/printk.c from
lib/dump_stack.c. Because linkage is per objecct file,
dump_stack_print_info() living in the same lib file as generic
dump_stack() means that archs which implement custom dump_stack()
- at this point, only blackfin - can't use dump_stack_print_info()
as that will bring in the generic version of dump_stack() too. v1
The v1 patch broke build on blackfin due to this issue. The build
breakage was reported by Fengguang Wu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390 bits]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Idle poller with an extra check_pgt_cache() invocation. Use the core
code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130321215234.886530981@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull OpenRISC updates from Jonas Bonn:
"An equal number of bug fixes and trivial cleanups; no new features.
- Two patches to fix errors thrown by the updated toolchain.
- Three other bug fixes.
- Four trivial cleanups."
* 'for-upstream' of git://openrisc.net/jonas/linux:
openrisc: add missing header inclusion
openrisc: really pass correct arg to schedule_tail
Add bitops include needed for ext2 filesystem
openrisc: update DTLB-miss handler last
openrisc: fix up vmalloc page table loading
openrisc idle: delete pm_idle
openrisc: remove CONFIG_SYMBOL_PREFIX
openrisc: avoid using function parameter regs in reset vector
openrisc: remove unused current_regs
Prevents build issue with updated toolchain
Reported-by: Jack Thomasson <jkt@moonlitsw.com>
Tested-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Pull signal handling cleanups from Al Viro:
"This is the first pile; another one will come a bit later and will
contain SYSCALL_DEFINE-related patches.
- a bunch of signal-related syscalls (both native and compat)
unified.
- a bunch of compat syscalls switched to COMPAT_SYSCALL_DEFINE
(fixing several potential problems with missing argument
validation, while we are at it)
- a lot of now-pointless wrappers killed
- a couple of architectures (cris and hexagon) forgot to save
altstack settings into sigframe, even though they used the
(uninitialized) values in sigreturn; fixed.
- microblaze fixes for delivery of multiple signals arriving at once
- saner set of helpers for signal delivery introduced, several
architectures switched to using those."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (143 commits)
x86: convert to ksignal
sparc: convert to ksignal
arm: switch to struct ksignal * passing
alpha: pass k_sigaction and siginfo_t using ksignal pointer
burying unused conditionals
make do_sigaltstack() static
arm64: switch to generic old sigaction() (compat-only)
arm64: switch to generic compat rt_sigaction()
arm64: switch compat to generic old sigsuspend
arm64: switch to generic compat rt_sigqueueinfo()
arm64: switch to generic compat rt_sigpending()
arm64: switch to generic compat rt_sigprocmask()
arm64: switch to generic sigaltstack
sparc: switch to generic old sigsuspend
sparc: COMPAT_SYSCALL_DEFINE does all sign-extension as well as SYSCALL_DEFINE
sparc: kill sign-extending wrappers for native syscalls
kill sparc32_open()
sparc: switch to use of generic old sigaction
sparc: switch sys_compat_rt_sigaction() to COMPAT_SYSCALL_DEFINE
mips: switch to generic sys_fork() and sys_clone()
...
Commit 287ad220cd tried to set up the argument
to schedule_tail, but ended up using TI_STACK which isn't a defined symbol.
Sadly, the old openrisc compiler silently ignores this fact and it was first
discovered now when building with an updated toolchain.
Reported-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
vmalloc'ed pages are faulted into a process' page tables on demand. In
order to facilitate this, do_page_fault needs to know whether it was
called via a page fault exception or a TLB-miss exception.
This patch adds a wrapper around the _x_page_fault_handler entry points
that the TLB-miss exceptions can call into in order to have the relevant
parameter set to satisfy do_page_fault.
This fixes a bug and is "good enough" for now. That said, this whole
handling of vmalloc needs to be audited for correctness at some point.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
pm_idle() on openrisc was dead code.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: linux@lists.openrisc.net
Signed-off-by: Jonas Bonn <jonas@southpole.se>
The kernel might be invoked through the reset vector, so to
preserve parameters passed to it, temp regs that are not
in the function parameter range needs to be used.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlDQeY8ACgkQ70gcjN2673NqLACgk1Uiw64UHI+uDVeB4mXYeUrO
C8UAnAgHumM61Mm5oiGRa1XzGSvxHQdK
=wVDf
-----END PGP SIGNATURE-----
Merge tag 'for-3.8' of git://openrisc.net/~jonas/linux
Pull OpenRISC update from Jonas Bonn:
"Trivial cleanups for OpenRISC."
* tag 'for-3.8' of git://openrisc.net/~jonas/linux:
openrisc: use kbuild.h instead of defining macros in asm-offset.c
openrisc: Use Kbuild infrastructure for kvm_para.h
This is modelled on commits such as the one below:
Commit fc1c3a003e ("sh: use kbuild.h
instead of defining macros in asm-offsets.c") introduced in v2.6.26.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
schedule_tail() requires that the 'prev' task be passed as an argument
to it. This arg is set in _switch, just before 'returning' to one of
the ret_* functions where schedule_tail is invoked.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Fixups for some corner cases, build issues, and some obvious bugs in
IRQ handling. No major changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAlB2kfsACgkQ70gcjN2673PxDQCdF7rldDDP3yCjd98/utGgdpjS
EJAAnAqIbf8oWfvMzfzo22rImXo/naio
=sO+p
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://openrisc.net/jonas/linux
Pull OpenRISC updates from Jonas Bonn:
"Fixups for some corner cases, build issues, and some obvious bugs in
IRQ handling. No major changes."
* tag 'for-3.7' of git://openrisc.net/jonas/linux:
openrisc: mask interrupts in irq_mask_ack function
openrisc: fix typos in comments and warnings
openrisc: PIC should act on domain-local irqs
openrisc: Make cpu_relax() invoke barrier()
audit: define AUDIT_ARCH_OPENRISC
openrisc: delay: fix handling of counter overflow
openrisc: delay: fix loops calculation for __const_udelay
getname() is intended to copy pathname strings from userspace into a
kernel buffer. The result is just a string in kernel space. It would
however be quite helpful to be able to attach some ancillary info to
the string.
For instance, we could attach some audit-related info to reduce the
amount of audit-related processing needed. When auditing is enabled,
we could also call getname() on the string more than once and not
need to recopy it from userspace.
This patchset converts the getname()/putname() interfaces to return
a struct instead of a string. For now, the struct just tracks the
string in kernel space and the original userland pointer for it.
Later, we'll add other information to the struct as it becomes
convenient.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that IRQ domains are in use, we should be acting on domain-local
IRQ numbers (hwirq) instead of 'global' ones.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
When using audit on OpenRISC, an audit arch is needed. This defines
it and fixes a compile-time bug uncovered in linux-next, likely from a
cut/paste from an arch with 64/32-bit modes that defined arch_arch():
arch/openrisc/kernel/ptrace.c:190:2: error: implicit declaration of function 'audit_arch'
This replaces it with the newly defined AUDIT_ARCH_OPENRISC, since it
is only 32-bit, and currently only operates in big-endian mode.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Does block_sigmask() + tracehook_signal_handler(); called when
sigframe has been successfully built. All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).
I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only 3 out of 63 do not. Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
replace boilerplate "should we use ->saved_sigmask or ->blocked?"
with calls of obvious inlined helper...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper. Open-coded instances switched...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull smp hotplug cleanups from Thomas Gleixner:
"This series is merily a cleanup of code copied around in arch/* and
not changing any of the real cpu hotplug horrors yet. I wish I'd had
something more substantial for 3.5, but I underestimated the lurking
horror..."
Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
um: Remove leftover declaration of alloc_task_struct_node()
task_allocator: Use config switches instead of magic defines
sparc: Use common threadinfo allocator
score: Use common threadinfo allocator
sh-use-common-threadinfo-allocator
mn10300: Use common threadinfo allocator
powerpc: Use common threadinfo allocator
mips: Use common threadinfo allocator
hexagon: Use common threadinfo allocator
m32r: Use common threadinfo allocator
frv: Use common threadinfo allocator
cris: Use common threadinfo allocator
x86: Use common threadinfo allocator
c6x: Use common threadinfo allocator
fork: Provide kmemcache based thread_info allocator
tile: Use common threadinfo allocator
fork: Provide weak arch_release_[task_struct|thread_info] functions
fork: Move thread info gfp flags to header
fork: Remove the weak insanity
sh: Remove cpu_idle_wait()
...
The function sys_or1k_atomic was using call-saved registers without
restoring their value before returning. This is a faux pas: either
we need to restore their values or use scratch regs; the latter is
less code so that's the route this patch takes.
Thanks to David Hennerström for doing most of the heavy-lifting in
tracking this one down.
Reported-by: Davd Hennerström <david.hennerstrom@aacmicrotec.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
This switches OpenRISC over to fully using the generic dma-mapping
framework. This was almost already the case as the architecture's
implementation was essentially a copy of the generic header.
This also brings this architecture in line with the recent changes
to dma_map_ops (adding attributes to ops->alloc).
Signed-off-by: Jonas Bonn <jonas@southpole.se>
This moves OpenRISC to using the irqdomain infrastructure. This doesn't
fundamentally change anything other than that it will be easier to have
multiple interrupt controllers in the future.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Same code. Use the generic version. The special Makefile treatment is
pointless anyway as init_task.o contains only data which is handled by
the linker script. So no point on being treated like head text.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jonas Bonn <jonas@southpole.se>
Link: http://lkml.kernel.org/r/20120503085035.083343435@linutronix.de
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAT3NKzROxKuMESys7AQKElw/+JyDxJSlj+g+nymkx8IVVuU8CsEwNLgRk
8KEnRfLhGtkXFLSJYWO6jzGo16F8Uqli1PdMFte/wagSv0285/HZaKlkkBVHdJ/m
u40oSjgT013bBh6MQ0Oaf8pFezFUiQB5zPOA9QGaLVGDLXCmgqUgd7exaD5wRIwB
ZmyItjZeAVnDfk1R+ZiNYytHAi8A5wSB+eFDCIQYgyulA1Igd1UnRtx+dRKbvc/m
rWQ6KWbZHIdvP1ksd8wHHkrlUD2pEeJ8glJLsZUhMm/5oMf/8RmOCvmo8rvE/qwl
eDQ1h4cGYlfjobxXZMHqAN9m7Jg2bI946HZjdb7/7oCeO6VW3FwPZ/Ic75p+wp45
HXJTItufERYk6QxShiOKvA+QexnYwY0IT5oRP4DrhdVB/X9cl2MoaZHC+RbYLQy+
/5VNZKi38iK4F9AbFamS7kd0i5QszA/ZzEzKZ6VMuOp3W/fagpn4ZJT1LIA3m4A9
Q0cj24mqeyCfjysu0TMbPtaN+Yjeu1o1OFRvM8XffbZsp5bNzuTDEvviJ2NXw4vK
4qUHulhYSEWcu9YgAZXvEWDEM78FXCkg2v/CrZXH5tyc95kUkMPcgG+QZBB5wElR
FaOKpiC/BuNIGEf02IZQ4nfDxE90QwnDeoYeV+FvNj9UEOopJ5z5bMPoTHxm4cCD
NypQthI85pc=
=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
The pt_regs struct had both a 'syscallno' field and an 'orig_gpr11' field
and it wasn't really clear how these were supposed to be used. This patch
removes the syscallno field altogether and makes orig_gpr11 work more
like other architectures: keep track of syscall number in progress or
hold -1 for non-syscall exceptions.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
dump_stack() is used by modules and needs to be exported.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
It takes a couple of instructions to actually configure a clock event
so setting an alarm just 1 clock cycle in the future isn't going to work;
doing so results in setting an alarm in the "past" in which case the event
won't fire until the timer overflows and rolls back around to the "current
time".
Not quite sure how many clock cycles it actually takes to get through to
actually writing the register, but 100 seems to work reliably.
Use generic helper to set up the clock event while we're at it.
Reported-by: Jan Schulte <jan.schulte@aacmicrotec.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block
is pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this
code wrong, so using this helper function should stop that from
happening again.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux@lists.openrisc.net
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
setup_rt_frame() needs to return an indication of whether it succeeded
or failed in setting up the signal stack frame. If setup_rt_frame()
fails then we must not modify current->blocked.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux@lists.openrisc.net
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
get_signal_to_deliver() already resets the signal handler if
SA_ONESHOT is set in ka->sa.sa_flags, there's no need to do it again
in handle_signal(). Furthermore, because we were modifying
ka->sa.sa_handler (which is a copy of sighand->action[]) instead of
sighand->action[] the original code actually had no effect on signal
delivery.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux@lists.openrisc.net
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Instead of open coding the sequence from force_sigsegv() just call
it. This also fixes a bug because we were modifying ka->sa.sa_handler
(which is a copy of sighand->action[]), whereas the intention of the
code was to modify sighand->action[] directly.
As the original code was working with a copy it had no effect on
signal delivery.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux@lists.openrisc.net
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
This patch enables passing a fdt pointer to the kernel.
This makes for the kernel parameter API:
void kernel(unsigned int fdt);
which, in accordance with the OpenRISC ABI results in:
r3 = pointer to fdt
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Commits d7e7528bcd and
b05d8447e7 simplified the usage of the
audit_syscall_[entry|exit] functions. Unfortunately, the OpenRISC
architecture didn't get fixed up along with the other architectures when
those patches were pushed. This makes the relevant changes to this
architecture.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (64 commits)
cpu: Export cpu_up()
rcu: Apply ACCESS_ONCE() to rcu_boost() return value
Revert "rcu: Permit rt_mutex_unlock() with irqs disabled"
docs: Additional LWN links to RCU API
rcu: Augment rcu_batch_end tracing for idle and callback state
rcu: Add rcutorture tests for srcu_read_lock_raw()
rcu: Make rcutorture test for hotpluggability before offlining CPUs
driver-core/cpu: Expose hotpluggability to the rest of the kernel
rcu: Remove redundant rcu_cpu_stall_suppress declaration
rcu: Adaptive dyntick-idle preparation
rcu: Keep invoking callbacks if CPU otherwise idle
rcu: Irq nesting is always 0 on rcu_enter_idle_common
rcu: Don't check irq nesting from rcu idle entry/exit
rcu: Permit dyntick-idle with callbacks pending
rcu: Document same-context read-side constraints
rcu: Identify dyntick-idle CPUs on first force_quiescent_state() pass
rcu: Remove dynticks false positives and RCU failures
rcu: Reduce latency of rcu_prepare_for_idle()
rcu: Eliminate RCU_FAST_NO_HZ grace-period hang
rcu: Avoid needlessly IPIing CPUs at GP end
...
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.
Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.
To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().
If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().
Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:
- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:
- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.
There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.
Split this function into:
- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.
- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).
To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().
This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The only function of memblock_analyze() is now allowing resize of
memblock region arrays. Rename it to memblock_allow_resize() and
update its users.
* The following users remain the same other than renaming.
arm/mm/init.c::arm_memblock_init()
microblaze/kernel/prom.c::early_init_devtree()
powerpc/kernel/prom.c::early_init_devtree()
openrisc/kernel/prom.c::early_init_devtree()
sh/mm/init.c::paging_init()
sparc/mm/init_64.c::paging_init()
unicore32/mm/init.c::uc32_memblock_init()
* In the following users, analyze was used to update total size which
is no longer necessary.
powerpc/kernel/machine_kexec.c::reserve_crashkernel()
powerpc/kernel/prom.c::early_init_devtree()
powerpc/mm/init_32.c::MMU_init()
powerpc/mm/tlb_nohash.c::__early_init_mmu()
powerpc/platforms/ps3/mm.c::ps3_mm_add_memory()
powerpc/platforms/embedded6xx/wii.c::wii_memory_fixups()
sh/kernel/machine_kexec.c::reserve_crashkernel()
* x86/kernel/e820.c::memblock_x86_fill() was directly setting
memblock_can_resize before populating memblock and calling analyze
afterwards. Call memblock_allow_resize() before start populating.
memblock_can_resize is now static inside memblock.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
memblock_init() initializes arrays for regions and memblock itself;
however, all these can be done with struct initializers and
memblock_init() can be removed. This patch kills memblock_init() and
initializes memblock with struct initializer.
The only difference is that the first dummy entries don't have .nid
set to MAX_NUMNODES initially. This doesn't cause any behavior
difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
For the initial architecture submission, not all of the DMA ops were
implemented. This patch adds the *map_page and *map_sg variants of the
DMA mapping ops.
This patch is currently of interest mainly to some drivers that haven't
been submitted upstream yet.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
As it was decided not to export struct pt_regs to userspace, struct
sigcontext shouldn't be using it either. The pt_regs struct for OpenRISC
is kernel internal and the layout of the registers may change in the
future. The struct user_regs_struct is what is guaranteed to remain
stable, so struct sigcontext may use that instead.
This patch removes the usage of struct pt_regs in struct sigcontext and
makes according changes in signal.c to get the register layout right.
The usp field is removed from the sigcontext structure as this information
is already contained in the user_regs_struct.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Emilio Cota <cota@braap.org>
Adds README file, TODO list, and a couple of other pieces that didn't seem
to fit into any other patch.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The OpenRISC Linux kernel conforms to the "generic" syscall interface which
contains only the reduced set of syscalls deemed necessary for new
architectures. Unfortunately, the uClibc port for OpenRISC does not fully
support this reduced set; as such, an additional patch available out-of-tree
needs to be applied to the kernel in order to use the current uClibc. This
is just a temporary measure until the libc port can be straightened out; it
is likely that OpenRISC will make the transition to glibc shortly where the
generic syscall interface is better supported.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support for the OpenRISC PIC.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Cc: tglx@linutronix.de
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Implements support for the OpenRISC timer which is a 28 bit cycle counter
that can be read out of a special purpose register. This counter is
used as a both a clock event and clocksource device.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Cc: tglx@linutronix.de
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This patch implements minimal PTrace support. The pt_regs structure is
not exported to userspace for OpenRISC; rather, the GETREGSET mechanism
is intended to be used and the registers, as such, exported in the core
dump format which is ABI stable. This is in line with what is intended
for new architectures as of 2.6.34 and has the advantage of permitting
the layout of the registers on the kernel stack (as per pt_regs) to be
freely modified.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The OpenRISC architecture uses the device tree infrastructure for the
platform description. This is currently limited to having a device tree
built into the kernel, but work is underway within the OpenRISC project
to define how this device tree blob should be passed into the kernel from
an external resource.
Patch contains a single example DTS file to go with the defconfig for
or1ksim.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Cc: devicetree-discuss@lists.ozlabs.org
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Architecture code and early setup routines for booting Linux.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Stafford Horne
Jan Henrik Weinstock
Stefan Kristiansson
Greg Kroah-Hartman
Linus Torvalds
Tobias Klauser
Vegard Nossum
Ingo Molnar
Masahiro Yamada
Olof Kindgren
Sebastian Macke
Paul Gortmaker
Bart Van Assche
Thomas Gleixner
Alexander Duyck
Rob Herring
Guenter Roeck
Christian Svensson
Jonas Bonn
Chris Metcalf
Krzysztof Kozlowski
Alexander Potapenko
Viresh Kumar
Joe Perches
Richard Weinberger
Al Viro
Andy Lutomirski
Kirill A. Shutemov
Eric Paris
Marc Zyngier
Geert Uytterhoeven
Rob Herring
Grant Likely
Santosh Shilimkar
Tejun Heo
Len Brown
James Hogan
Jeff Layton
Gong Tao
Kees Cook
David Howells
Matt Fleming
Frederic Weisbecker