commit 4270d2b484 upstream.
Do not transition to SNK_UNATTACHED state when receiving vsafe0v event
while in SNK_HARD_RESET_WAIT_VBUS. Ignore VBUS off events as well as
in some platforms VBUS off can be signalled more than once.
[143515.364753] Requesting mux state 1, usb-role 2, orientation 2
[143515.365520] pending state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_SINK_ON @ 650 ms [rev3 HARD_RESET]
[143515.632281] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_HARD_RESET_SINK_OFF, polarity 1, disconnected]
[143515.637214] VBUS on
[143515.664985] VBUS off
[143515.664992] state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_WAIT_VBUS [rev3 HARD_RESET]
[143515.665564] VBUS VSAFE0V
[143515.665566] state change SNK_HARD_RESET_WAIT_VBUS -> SNK_UNATTACHED [rev3 HARD_RESET]
Fixes: 28b43d3d74 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Cc: <stable@vger.kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230712085722.1414743-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e21a620c7 upstream.
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() because last_role is same
as current role. This happens since last_role gets initialised
to zero during the probe.
To avoid this, add a new flag initial_detection into struct
usb_conn_info, which prevents bailing out during initial
detection.
Cc: <stable@vger.kernel.org> # 5.4
Fixes: 4602f3bff2 ("usb: common: add USB GPIO based connection detection driver")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/1690880632-12588-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ddaa6a274 upstream.
If dwc3 is runtime suspended we defer processing the event buffer
until resume, by setting the pending_events flag. Set this flag before
triggering resume to avoid race with the runtime resume callback.
While handling the pending events, in addition to checking the event
buffer we also need to process it. Handle this by explicitly calling
dwc3_thread_interrupt(). Also balance the runtime pm get() operation
that triggered this processing.
Cc: stable@vger.kernel.org
Fixes: fc8bb91bc8 ("usb: dwc3: implement runtime PM")
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230801192658.19275-1-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6ff6e7a9d upstream.
Syzbot got KMSAN to complain about access to an uninitialized value in
the alauda subdriver of usb-storage:
BUG: KMSAN: uninit-value in alauda_transport+0x462/0x57f0
drivers/usb/storage/alauda.c:1137
CPU: 0 PID: 12279 Comm: usb-storage Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x13a/0x2b0 mm/kmsan/kmsan_report.c:108
__msan_warning+0x73/0xe0 mm/kmsan/kmsan_instr.c:250
alauda_check_media+0x344/0x3310 drivers/usb/storage/alauda.c:460
The problem is that alauda_check_media() doesn't verify that its USB
transfer succeeded before trying to use the received data. What
should happen if the transfer fails isn't entirely clear, but a
reasonably conservative approach is to pretend that no media is
present.
A similar problem exists in a usb_stor_dbg() call in
alauda_get_media_status(). In this case, when an error occurs the
call is redundant, because usb_stor_ctrl_transfer() already will print
a debugging message.
Finally, unrelated to the uninitialized memory access, is the fact
that alauda_check_media() performs DMA to a buffer on the stack.
Fortunately usb-storage provides a general purpose DMA-able buffer for
uses like this. We'll use it instead.
Reported-and-tested-by: syzbot+e7d46eb426883fb97efd@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/0000000000007d25ff059457342d@google.com/T/
Suggested-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: e80b0fade0 ("[PATCH] USB Storage: add alauda support")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/693d5d5e-f09b-42d0-8ed9-1f96cd30bcce@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 288b4fa179 upstream.
This reverts commit 18fc7c435b.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this code, the patch means that certain tegra_xusb_probe() will
fail if the firmware supports power-domains but CONFIG_PM is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 18fc7c435b ("usb: xhci: tegra: Fix error check")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/8baace8d-fb4b-41a4-ad5f-848ae643a23b@moroto.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2627335a13 upstream.
Previously, the cdns3_gadget_check_config() function in the cdns3 driver
mistakenly calculated the ep_buf_size by considering only one
configuration's endpoint information because "claimed" will be clear after
call usb_gadget_check_config().
The fix involves checking the private flags EP_CLAIMED instead of relying
on the "claimed" flag.
Fixes: dce49449e0 ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230707230015.494999-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dc162e223 upstream.
The Focusrite Scarlett audio device does not behave correctly during
resumes. Below is what happens during every resume (captured with
Beagle 5000):
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset/Target disconnected>
<High Speed>
The Scarlett disconnects and is enumerated again.
However from time to time it drops completely off the USB bus during
resume. Below is captured occurrence of such an event:
<Suspend>
<Resume>
<Reset>/<Chirp J>/<Tiny J>
<Reset>/<Chirp K>/<Tiny K>
<High Speed>
<Corrupted packet>
<Reset/Target disconnected>
To fix the condition a user has to unplug and plug the device again.
With USB_QUIRK_RESET_RESUME applied ("usbcore.quirks=1235:8211:b")
for the Scarlett audio device the issue still reproduces.
Applying USB_QUIRK_DISCONNECT_SUSPEND ("usbcore.quirks=1235:8211:m")
fixed the issue and the Scarlett audio device didn't drop off the USB
bus for ~5000 suspend/resume cycles where originally issue reproduced in
~100 or less suspend/resume cycles.
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20230724112911.1802577-1-lb@semihalf.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c55afcbeaa upstream.
The ohci_hcd_at91_drv_suspend() sets ohci->rh_state to OHCI_RH_HALTED when
suspend which will let the ohci_irq() skip the interrupt after resume. And
nobody to handle this interrupt.
According to the comment in ohci_hcd_at91_drv_suspend(), it need to reset
when resume from suspend(MEM) to fix by setting "hibernated" argument of
ohci_resume().
Signed-off-by: Guiting Shen <aarongt.shen@gmail.com>
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230626152713.18950-1-aarongt.shen@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e835c0a4e2 upstream.
Commit c4a5153e87 ("usb: dwc3: core: Power-off core/PHYs on
system_suspend in host mode") replaces check for HOST only dr_mode with
current_dr_role. But during booting, the current_dr_role isn't
initialized, thus the device side reset is always issued even if dwc3
was configured as host-only. What's more, on some platforms with host
only dwc3, aways issuing device side reset by accessing device register
block can cause kernel panic.
Fixes: c4a5153e87 ("usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode")
Cc: stable <stable@kernel.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230627162018.739-1-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b32b8f2b95 upstream.
Hardware based on the Bay Trail / BYT SoCs require an external ULPI phy for
USB device-mode. The phy chip usually has its 'reset' and 'chip select'
lines connected to GPIOs described by ACPI fwnodes in the DSDT table.
Because of hardware with missing ACPI resources for the 'reset' and 'chip
select' GPIOs commit 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table
on platforms without ACPI GPIO resources") introduced a fallback
gpiod_lookup_table with hard-coded mappings for Bay Trail devices.
However there are existing Bay Trail based devices, like the National
Instruments cRIO-903x series, where the phy chip has its 'reset' and
'chip-select' lines always asserted in hardware via resistor pull-ups. On
this hardware the phy chip is always enabled and the ACPI dsdt table is
missing information not only for the 'chip-select' and 'reset' lines but
also for the BYT GPIO controller itself "INT33FC".
With the introduction of the gpiod_lookup_table initializing the USB
device-mode on these hardware now errors out. The error comes from the
gpiod_get_optional() calls in dwc3_pci_quirks() which will now return an
-ENOENT error due to the missing ACPI entry for the INT33FC gpio controller
used in the aforementioned table.
This hardware used to work before because gpiod_get_optional() will return
NULL instead of -ENOENT if no GPIO has been assigned to the requested
function. The dwc3_pci_quirks() code for setting the 'cs' and 'reset' GPIOs
was then skipped (due to the NULL return). This is the correct behavior in
cases where the phy chip is hardwired and there are no GPIOs to control.
Since the gpiod_lookup_table relies on the presence of INT33FC fwnode
in ACPI tables only add the table if we know the entry for the INT33FC
gpio controller is present. This allows Bay Trail based devices with
hardwired dwc3 ULPI phys to continue working.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@kernel.org>
Signed-off-by: Gratian Crisan <gratian.crisan@ni.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230726184555.218091-2-gratian.crisan@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 734ae15ab9 upstream.
This reverts commit b138e23d3d.
AutoRetry has been found to sometimes cause controller freezes when
communicating with buggy USB devices.
This controller feature allows the controller in host mode to send
non-terminating/burst retry ACKs instead of terminating retry ACKs
to devices when a transaction error (CRC error or overflow) occurs.
Unfortunately, if the USB device continues to respond with a CRC error,
the controller will not complete endpoint-related commands while it
keeps trying to auto-retry. [3] The xHCI driver will notice this once
it tries to abort the transfer using a Stop Endpoint command and
does not receive a completion in time. [1]
This situation is reported to dmesg:
[sda] tag#29 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[sda] tag#29 CDB: opcode=0x28 28 00 00 69 42 80 00 00 48 00
xhci-hcd: xHCI host not responding to stop endpoint command
xhci-hcd: xHCI host controller not responding, assume dead
xhci-hcd: HC died; cleaning up
Some users observed this problem on an Odroid HC2 with the JMS578
USB3-to-SATA bridge. The issue can be triggered by starting
a read-heavy workload on an attached SSD. After a while, the host
controller would die and the SSD would disappear from the system. [1]
Further analysis by Synopsys determined that controller revisions
other than the one in Odroid HC2 are also affected by this.
The recommended solution was to disable AutoRetry altogether.
This change does not have a noticeable performance impact. [2]
Revert the enablement commit. This will keep the AutoRetry bit in
the default state configured during SoC design [2].
Fixes: b138e23d3d ("usb: dwc3: core: Enable AutoRetry feature in the controller")
Link: https://lore.kernel.org/r/a21f34c04632d250cd0a78c7c6f4a1c9c7a43142.camel@gmail.com/ [1]
Link: https://lore.kernel.org/r/20230711214834.kyr6ulync32d4ktk@synopsys.com/ [2]
Link: https://lore.kernel.org/r/20230712225518.2smu7wse6djc7l5o@synopsys.com/ [3]
Cc: stable@vger.kernel.org
Cc: Mauro Ribeiro <mauro.ribeiro@hardkernel.com>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jakub Vanek <linuxtardis@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230714122419.27741-1-linuxtardis@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d245aedc00 upstream.
Sort the driver symbols alphabetically in order to make it more obvious
where new driver entries should be added.
Cc: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd92c8a1f9 upstream.
Add the device and product ID for this CAN bus interface / license
dongle. The device is usable either directly from user space or can be
attached to a kernel CAN interface with slcan_attach.
Reported-by: Kaufmann Automotive GmbH <info@kaufmann-automotive.ch>
Tested-by: Kaufmann Automotive GmbH <info@kaufmann-automotive.ch>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
[ johan: amend commit message and move entries in sort order ]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4fc01af5b upstream.
The legacy gadget driver omitted calling usb_gadget_check_config()
to ensure that the USB device controller (UDC) has adequate resources,
including sufficient endpoint numbers and types, to support the given
configuration.
Previously, usb_add_config() was solely invoked by the legacy gadget
driver. Adds the necessary usb_gadget_check_config() after the bind()
operation to fix the issue.
Fixes: dce49449e0 ("usb: cdns3: allocate TX FIFO size according to composite EP number")
Cc: stable <stable@kernel.org>
Reported-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230707230015.494999-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8291be6b5 upstream.
This reverts commit f08aa7c80d.
The reverted commit was based on static analysis and a misunderstanding
of how PTR_ERR() and NULLs are supposed to work. When a function
returns both pointer errors and NULL then normally the NULL means
"continue operating without a feature because it was deliberately
turned off". The NULL should not be treated as a failure. If a driver
cannot work when that feature is disabled then the KConfig should
enforce that the function cannot return NULL. We should not need to
test for it.
In this driver, the bug means that probe cannot succeed when CONFIG_PM
is disabled.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: f08aa7c80d ("usb: gadget: tegra-xudc: Fix error check in tegra_xudc_powerdomain_init()")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/ZKQoBa84U/ykEh3C@moroto
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9b0328d0b upstream.
Some ZHAOXIN xHCI controllers follow usb3.1 spec, but only support
gen1 speed 5Gbps. While in Linux kernel, if xHCI suspport usb3.1,
root hub speed will show on 10Gbps.
To fix this issue of ZHAOXIN xHCI platforms, read usb speed ID
supported by xHCI to determine root hub speed. And add a quirk
XHCI_ZHAOXIN_HOST for this issue.
[fix warning about uninitialized symbol -Mathias]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-11-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a865a6522 upstream.
On some ZHAOXIN hosts, xHCI will prefetch TRB for performance
improvement. However this TRB prefetch mechanism may cross page boundary,
which may access memory not allocated by xHCI driver. In order to fix
this issue, two pages was allocated for a segment and only the first
page will be used. And add a quirk XHCI_ZHAOXIN_TRB_FETCH for this issue.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-10-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f927728186 upstream.
On ZHAOXIN ZX-100 project, xHCI can't work normally after resume
from system Sx state. To fix this issue, when resume from system
Sx state, reinitialize xHCI instead of restore.
So, Add XHCI_RESET_ON_RESUME quirk for ZX-100 to fix issue of
resuming from system Sx state.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-9-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df49f2a0ac ]
This reverts commit edd60d24bd.
Heikki reports that this should not be a global flag just to work around
one broken driver and should be fixed differently, so revert it.
Reported-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: edd60d24bd ("usb: common: usb-conn-gpio: Set last role to unknown before initial detection")
Link: https://lore.kernel.org/r/ZImE4L3YgABnCIsP@kuha.fi.intel.com
Cc: Prashanth K <quic_prashk@quicinc.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edd60d24bd ]
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() since last_role is same as
current role. This happens because during probe last_role gets
initialised to zero.
To avoid this, added a new constant in enum usb_role, last_role
is set to USB_ROLE_UNKNOWN before performing initial detection.
While at it, also handle default case for the usb_role switch
in cdns3, intel-xhci-usb-role-switch & musb/jz4740 to avoid
build warnings.
Fixes: 4602f3bff2 ("usb: common: add USB GPIO based connection detection driver")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <1685544074-17337-1-git-send-email-quic_prashk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a944da707 ]
If dwc3_qcom_create_urs_usb_platdev() fails, some resources still need to
be released, as already done in the other error handling path of the
probe.
Fixes: c25c210f59 ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <b69fa8dd68d816e7d24c88d3eda776ceb28c5dc5.1685890571.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fd95da2cf ]
In the probe, some resources are allocated with
dwc3_qcom_of_register_core() or dwc3_qcom_acpi_register_core(). The
corresponding resources are already coorectly freed in the error handling
path of the probe, but not in the remove function.
Fix it.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Message-ID: <c0215a84cdf18fb3514c81842783ec53cf149deb.1685891059.git.christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e6bd945e6 ]
The declaration is in an #ifdef, which causes warnings when building
with 'make W=1' and without CONFIG_PM:
drivers/usb/core/devio.c:742:6: error: no previous prototype for 'usbfs_notify_suspend'
drivers/usb/core/devio.c:747:6: error: no previous prototype for 'usbfs_notify_resume'
Use the same #ifdef check around the function definitions to avoid
the warnings and slightly shrink the USB core.
Fixes: 7794f486ed ("usbfs: Add ioctls for runtime power management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230516202103.558301-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 342161c114 ]
Smatch reports:
drivers/usb/phy/phy-tahvo.c: tahvo_usb_probe()
warn: missing unwind goto?
After geting irq, if ret < 0, it will return without error handling to
free memory.
Just add error handling to fix this problem.
Fixes: 0d45a1373e ("usb: phy: tahvo: add IRQ check")
Signed-off-by: Li Yang <lidaxian@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230420140832.9110-1-lidaxian@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f6ecb89fe ]
Consider a case where gserial_disconnect has already cleared
gser->ioport. And if gserial_suspend gets called afterwards,
it will lead to accessing of gser->ioport and thus causing
null pointer dereference.
Avoid this by adding a null pointer check. Added a static
spinlock to prevent gser->ioport from becoming null after
the newly added null pointer check.
Fixes: aba3a8d01d ("usb: gadget: u_serial: add suspend resume callbacks")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/1683278317-11774-1-git-send-email-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 097fb3ee71 ]
Function dwc3_qcom_probe() allocates memory for resource structure
which is pointed by parent_res pointer. This memory is not
freed. This leads to memory leak. Use stack memory to prevent
memory leak.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20230517172518.442591-1-VEfanov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada050c691 ]
dwc2_driver_probe() calls dwc2_lowlevel_hw_init() which deassert some reset
lines.
Should an error happen in dwc2_lowlevel_hw_init() after calling
reset_control_deassert() or in the probe after calling
dwc2_lowlevel_hw_init(), the reset lines remain deasserted.
Add some devm_add_action_or_reset() calls to re-assert the lines if needed.
Update the remove function accordingly.
This change is compile-tested only.
Fixes: 83f8da562f ("usb: dwc2: Add reset control to dwc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/c64537b5339342bd00f7c2152b8fc23792b9f95a.1683306479.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55f223b8b4 ]
Returning an error value in a platform driver's remove callback results in
a generic error message being emitted by the driver core, but otherwise it
doesn't make a difference. The device goes away anyhow.
For each case where ret is non-zero the driver already emits an error
message, so suppress the generic error message by returning zero
unconditionally. (Side note: The return value handling was unreliable
anyhow as the value returned by dwc2_exit_hibernation() was overwritten
anyhow if hsotg->in_ppd was non-zero.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20221017195914.1426297-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: ada050c691 ("usb: dwc2: Fix some error handling paths")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c0aabed9ca upstream.
In scenarios where pullup relies on resume (get sync) to initialize
the controller and set the run stop bit, then core_init is followed by
gadget_resume which will eventually set run stop bit.
But in cases where the core_init fails, the return value is not sent
back to udc appropriately. So according to UDC the controller has
started but in reality we never set the run stop bit.
On systems like Android, there are uevents sent to HAL depending on
whether the configfs_bind / configfs_disconnect were invoked. In the
above mentioned scnenario, if the core init fails, the run stop won't
be set and the cable plug-out won't result in generation of any
disconnect event and userspace would never get any uevent regarding
cable plug out and we never call pullup(0) again. Furthermore none of
the next Plug-In/Plug-Out's would be known to configfs.
Return back the appropriate result to UDC to let the userspace/
configfs know that the pullup failed so they can take appropriate
action.
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <20230618120949.14868-1-quic_kriskura@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffa5f7a3bf upstream.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 USB configurations (default, RmNet,
CDC-ECM) are the same.
In default mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
In RmNet mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
If 4: RMNET interface
In CDC-ECM mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Link: https://lore.kernel.org/r/20230622092921.12651-1-davide.tronchin.94@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 016da9c65f ]
The "udc" pointer was never set in the probe() function so it will
lead to a NULL dereference in udc_pci_remove() when we do:
usb_del_gadget_udc(&udc->gadget);
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/ZG+A/dNpFWAlCChk@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 00f8205ffc upstream.
Consider a scenario where cable disconnect happens when there is an active
usb reqest queued to the UDC. As part of the disconnect we would issue an
end transfer with no interrupt-on-completion before giving back this
request. Since we are giving back the request without skipping TRBs the
num_trbs field of dwc3_request still holds the stale value previously used.
Function drivers re-use same request for a given bind-unbind session and
hence their dwc3_request context gets preserved across cable
disconnect/connect. When such a request gets re-queued after cable connect,
we would increase the num_trbs field on top of the previous stale value
thus incorrectly representing the number of TRBs used. Fix this by
resetting num_trbs field before giving back the request.
Fixes: 09fe1f8d7e ("usb: dwc3: gadget: track number of TRBs per request")
Cc: stable <stable@kernel.org>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Message-ID: <1685654850-8468-1-git-send-email-quic_eserrao@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0b861653f upstream.
When hcd->localmem_pool is non-null, localmem_pool is used to allocate
DMA memory. In this case, the dma address will be properly returned (in
dma_handle), and dma_mmap_coherent should be used to map this memory
into the user space. However, the current implementation uses
pfn_remap_range, which is supposed to map normal pages.
Instead of repeating the logic in the memory allocation function, this
patch introduces a more robust solution. Here, the type of allocated
memory is checked by testing whether dma_handle is properly set. If
dma_handle is properly returned, it means some DMA pages are allocated
and dma_mmap_coherent should be used to map them. Otherwise, normal
pages are allocated and pfn_remap_range should be called. This ensures
that the correct mmap functions are used consistently, independently
with logic details that determine which type of memory gets allocated.
Fixes: a0e710a7de ("USB: usbfs: fix mmap dma mismatch")
Cc: stable@vger.kernel.org
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Link: https://lore.kernel.org/r/20230515130958.32471-3-lrh2000@pku.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0143d148d1 upstream.
The current implementation of usbdev_mmap uses usb_alloc_coherent to
allocate memory pages that will later be mapped into the user space.
Meanwhile, usb_alloc_coherent employs three different methods to
allocate memory, as outlined below:
* If hcd->localmem_pool is non-null, it uses gen_pool_dma_alloc to
allocate memory;
* If DMA is not available, it uses kmalloc to allocate memory;
* Otherwise, it uses dma_alloc_coherent.
However, it should be noted that gen_pool_dma_alloc does not guarantee
that the resulting memory will be page-aligned. Furthermore, trying to
map slab pages (i.e., memory allocated by kmalloc) into the user space
is not resonable and can lead to problems, such as a type confusion bug
when PAGE_TABLE_CHECK=y [1].
To address these issues, this patch introduces hcd_alloc_coherent_pages,
which addresses the above two problems. Specifically,
hcd_alloc_coherent_pages uses gen_pool_dma_alloc_align instead of
gen_pool_dma_alloc to ensure that the memory is page-aligned. To replace
kmalloc, hcd_alloc_coherent_pages directly allocates pages by calling
__get_free_pages.
Reported-by: syzbot+fcf1a817ceb50935ce99@syzkaller.appspotmail.comm
Closes: https://lore.kernel.org/lkml/000000000000258e5e05fae79fc1@google.com/ [1]
Fixes: f7d34b445a ("USB: Add support for usbfs zerocopy.")
Fixes: ff2437befd ("usb: host: Fix excessive alignment restriction for local memory allocations")
Cc: stable@vger.kernel.org
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230515130958.32471-2-lrh2000@pku.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dbe678f619 ]
At iMX8QM platform, enable NCM gadget and run 'iperf3 -s'.
At host, run 'iperf3 -V -c fe80::6863:98ff:feef:3e0%enxc6e147509498'
[ 5] 0.00-1.00 sec 1.55 MBytes 13.0 Mbits/sec 90 4.18 KBytes
[ 5] 1.00-2.00 sec 1.44 MBytes 12.0 Mbits/sec 75 4.18 KBytes
[ 5] 2.00-3.00 sec 1.48 MBytes 12.4 Mbits/sec 75 4.18 KBytes
Expected speed should be bigger than 300Mbits/sec.
The root cause of this performance drop was found to be data corruption
happening at 4K borders in some Ethernet packets, leading to TCP
checksum errors. This corruption occurs from the position
(4K - (address & 0x7F)) to 4K. The u_ether function's allocation of
skb_buff reserves 64B, meaning all RX addresses resemble 0xXXXX0040.
Force trb_burst_size to 16 can fix this problem.
Cc: stable@vger.kernel.org
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230518154946.3666662-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dce49449e0 ]
Some devices have USB compositions which may require multiple endpoints.
To get better performance, need bigger CDNS3_EP_BUF_SIZE.
But bigger CDNS3_EP_BUF_SIZE may exceed total hardware FIFO size when
multiple endpoints.
By introducing the check_config() callback, calculate CDNS3_EP_BUF_SIZE.
Move CDNS3_EP_BUF_SIZE into cnds3_device: ep_buf_size
Combine CDNS3_EP_ISO_SS_BURST and CDNS3_EP_ISO_HS_MULT into
cnds3_device:ep_iso_burst
Using a simple algorithm to calculate ep_buf_size.
ep_buf_size = ep_iso_burst = (onchip_buffers - 2k) / (number of IN EP +
1).
Test at 8qxp:
Gadget ep_buf_size
RNDIS: 5
RNDIS+ACM: 3
Mass Storage + NCM + ACM 2
Previous CDNS3_EP_BUF_SIZE is 4, RNDIS + ACM will be failure because
exceed FIFO memory.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20220509164055.1815081-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: dbe678f619 ("usb: cdns3: fix NCM gadget RX speed 20x slow than expection at iMX8QM")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit efb6b53520 upstream.
While exercising the unbind path, with the current implementation
the functionfs_unbind would be calling which waits for the ffs->mutex
to be available, however within the same time ffs_ep0_read is invoked
& if no setup packets are pending, it will invoke function
wait_event_interruptible_exclusive_locked_irq which by definition waits
for the ev.count to be increased inside the same mutex for which
functionfs_unbind is waiting.
This creates deadlock situation because the functionfs_unbind won't
get the lock until ev.count is increased which can only happen if
the caller ffs_func_unbind can proceed further.
Following is the illustration:
CPU1 CPU2
ffs_func_unbind() ffs_ep0_read()
mutex_lock(ffs->mutex)
wait_event(ffs->ev.count)
functionfs_unbind()
mutex_lock(ffs->mutex)
mutex_unlock(ffs->mutex)
ffs_event_add()
<deadlock>
Fix this by moving the event unbind before functionfs_unbind
to ensure the ev.count is incrased properly.
Fixes: 6a19da1110 ("usb: gadget: f_fs: Prevent race during ffs_ep0_queue_wait")
Cc: stable <stable@kernel.org>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20230525092854.7992-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1389062650 upstream.
Many of the older USB drivers in the Linux USB stack were written
based simply on a vendor's device specification. They use the
endpoint information in the spec and assume these endpoints will
always be present, with the properties listed, in any device matching
the given vendor and product IDs.
While that may have been true back then, with spoofing and fuzzing it
is not true any more. More and more we are finding that those old
drivers need to perform at least a minimum of checking before they try
to use any endpoint other than ep0.
To make this checking as simple as possible, we now add a couple of
utility routines to the USB core. usb_check_bulk_endpoints() and
usb_check_int_endpoints() take an interface pointer together with a
list of endpoint addresses (numbers and directions). They check that
the interface's current alternate setting includes endpoints with
those addresses and that each of these endpoints has the right type:
bulk or interrupt, respectively.
Although we already have usb_find_common_endpoints() and related
routines meant for a similar purpose, they are not well suited for
this kind of checking. Those routines find endpoints of various
kinds, but only one (either the first or the last) of each kind, and
they don't verify that the endpoints' addresses agree with what the
caller expects.
In theory the new routines could be more general: They could take a
particular altsetting as their argument instead of always using the
interface's current altsetting. In practice I think this won't matter
too much; multiple altsettings tend to be used for transferring media
(audio or visual) over isochronous endpoints, not bulk or interrupt.
Drivers for such devices will generally require more sophisticated
checking than these simplistic routines provide.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/dd2c8e8c-2c87-44ea-ba17-c64b97e201c9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4e8ef34e36 ]
When work in gadget mode, currently driver doesn't update software level
link_state correctly as link state change event is not enabled for most
devices, in function dwc3_gadget_suspend_interrupt(), it will only pass
suspend event to UDC core when software level link state changes, so when
interrupt generated in sequences of suspend -> reset -> conndone ->
suspend, link state is not updated during reset and conndone, so second
suspend interrupt event will not pass to UDC core.
Remove link_state compare in dwc3_gadget_suspend_interrupt() and add a
suspended flag to replace the compare function.
Fixes: 799e9dc829 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/20230512004524.31950-1-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b93c2a68f3 ]
The wakeup bit in the bmAttributes field indicates whether the device
is configured for remote wakeup. But this field should be allowed to
set only if the UDC supports such wakeup mechanism. So configure this
field based on UDC capability. Also inform the UDC whether the device
is configured for remote wakeup by implementing a gadget op.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com>
Link: https://lore.kernel.org/r/1679694482-16430-2-git-send-email-quic_eserrao@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 4e8ef34e36 ("usb: dwc3: fix gadget mode suspend interrupt handler issue")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fe82f16aaf upstream.
This incorrect tracking caused unnecessary ring expansion in some
usecases which over days of use consume a lot of memory.
xhci driver tries to keep track of free transfer blocks (TRBs) on the
ring buffer, but failed to add back some cancelled transfers that were
turned into no-op operations instead of just moving past them.
This can happen if there are several queued pending transfers which
then are cancelled in reverse order.
Solve this by counting the numer of steps we move the dequeue pointer
once we complete a transfer, and add it to the number of free trbs
instead of just adding the trb number of the current transfer.
This way we ensure we count the no-op trbs on the way as well.
Fixes: 55f6153d8c ("xhci: remove extra loop in interrupt context")
Cc: stable@vger.kernel.org
Reported-by: Miller Hunter <MillerH@hearthnhome.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217242
Tested-by: Miller Hunter <MillerH@hearthnhome.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230515134059.161110-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a821fc313 upstream.
Donghun reports that a notebook that has an AMD Ryzen 5700U but supports
S3 has problems with USB after resuming from suspend. The issue was
bisected down to commit d1658268e4 ("usb: pci-quirks: disable D3cold on
xhci suspend for s2idle on AMD Renoir").
As this issue only happens on S3, narrow the broken D3cold quirk to only
run in s2idle.
Fixes: d1658268e4 ("usb: pci-quirks: disable D3cold on xhci suspend for s2idle on AMD Renoir")
Reported-and-tested-by: Donghun Yoon <donghun.yoon@lge.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230515134059.161110-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Badhri Jagan Sridharan
Prashanth K
Elson Roy Serrao
Alan Stern
Oliver Neukum
Dan Carpenter
Ricardo Ribalda
Frank Li
Łukasz Bartosik
Guiting Shen
Jisheng Zhang
Gratian Crisan
Jakub Vanek
Johan Hovold
Mohsen Tahmasebi
Jerry Meng
Zqiang
Weitao Wang
Greg Kroah-Hartman
Christophe JAILLET
Arnd Bergmann
Li Yang
Vladislav Efanov
Uwe Kleine-König
Krishna Kurapati
Davide Tronchin
Ruihan Li
Uttkarsh Aggarwal
Linyu Yuan
Mathias Nyman
Mario Limonciello