Add the DMA engine driver for the QCOM Bus Access Manager (BAM) DMA controller
found in the MSM 8x74 platforms.
Each BAM DMA device is associated with a specific on-chip peripheral. Each
channel provides a uni-directional data transfer engine that is capable of
transferring data between the peripheral and system memory (System mode), or
between two peripherals (BAM2BAM).
The initial release of this driver only supports slave transfers between
peripherals and system memory.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Tested-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The MOXA ART SoC has a DMA controller capable of offloading expensive
memory operations, such as large copies. This patch adds support for
the controller including four channels. Two of these are used to
handle MMC copy on the UC-7112-LX hardware. The remaining two can be
used in a future audio driver or client application.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for DMA controller of BCM2835 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This adds a new driver to support the s3c24xx dma using the dmaengine
and makes the old one in mach-s3c24xx obsolete in the long run.
Conceptually the s3c24xx-dma feels like a distant relative of the pl08x
with numerous virtual channels being mapped to a lot less physical ones.
The driver therefore borrows a lot from the amba-pl08x driver in this
regard. Functionality-wise the driver gains a memcpy ability in addition
to the slave_sg one.
The driver supports both the method for requesting the peripheral used
by SoCs before the S3C2443 and the different method for S3C2443 and later.
On earlier SoCs the hardware channels usable for specific peripherals is
constrainted while on later SoCs all channels can be used for any peripheral.
Tested on a s3c2416-based board, memcpy using the dmatest module and
slave_sg partially using the spi-s3c64xx driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull slave-dmaengine updates from Vinod Koul:
"This pull brings:
- Andy's DW driver updates
- Guennadi's sh driver updates
- Pl08x driver fixes from Tomasz & Alban
- Improvements to mmp_pdma by Daniel
- TI EDMA fixes by Joel
- New drivers:
- Hisilicon k3dma driver
- Renesas rcar dma driver
- New API for publishing slave driver capablities
- Various fixes across the subsystem by Andy, Jingoo, Sachin etc..."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (94 commits)
dma: edma: Remove limits on number of slots
dma: edma: Leave linked to Null slot instead of DUMMY slot
dma: edma: Find missed events and issue them
ARM: edma: Add function to manually trigger an EDMA channel
dma: edma: Write out and handle MAX_NR_SG at a given time
dma: edma: Setup parameters to DMA MAX_NR_SG at a time
dmaengine: pl330: use dma_set_max_seg_size to set the sg limit
dmaengine: dma_slave_caps: remove sg entries
dma: replace devm_request_and_ioremap by devm_ioremap_resource
dma: ste_dma40: Fix potential null pointer dereference
dma: ste_dma40: Remove duplicate const
dma: imx-dma: Remove redundant NULL check
dma: dmagengine: fix function names in comments
dma: add driver for R-Car HPB-DMAC
dma: k3dma: use devm_ioremap_resource() instead of devm_request_and_ioremap()
dma: imx-sdma: Staticize sdma_driver_data structures
pch_dma: Add MODULE_DEVICE_TABLE
dmaengine: PL08x: Add cyclic transfer support
dmaengine: PL08x: Fix reading the byte count in cctl
dmaengine: PL08x: Add support for different maximum transfer size
...
This driver is currently used by musb' cppi41 couter part. I may merge
both dma engine user of musb at some point but not just yet.
The driver seems to work in RX/TX mode in host mode, tested on mass
storage. I increaed the size of the TX / RX transfers and waited for the
core code to cancel a transfers and it seems to recover.
v2..3:
- use mall transfers on RX side and check data toggle.
- use rndis mode on tx side so we haveon interrupt for 4096 transfers.
- remove custom "transferred" hack and use dmaengine_tx_status() to
compute the total amount of data that has been transferred.
- cancel transfers and reclaim descriptors
v1..v2:
- RX path added
- dma mode 0 & 1 is working
- device tree nodes re-created.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds dmaengine support for the JZ4740 DMA controller. For now the
driver will be a wrapper around the custom JZ4740 DMA API. Once all users of the
custom JZ4740 DMA API have been converted to the dmaengine API the custom API
will be removed and direct hardware access will be added to the dmaengine
driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
To simplify the driver development let's split driver to library and platform
code parts. It helps us to add PCI driver in future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[Fixed compile error and few checkpatch issues]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dw_dmac driver is going to be split into multiple files. To make this more
convenient move it to an own directory.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds Kconfig in the drivers/dma/sh. This patch also adds
a new config "SH_DMAE_BASE" and the "config SH_DMAE" depends on it.
Since some drivers (e.g. sh_mmcif.c) depends on shdma-base.c if
CONFIG_DMA_ENGINE=y, the "config SH_DMAE_BASE" is set as "bool".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a new generic API to get a DMA channel for a slave device (commit
9a6cecc8 "dmaengine: add helper function to request a slave DMA channel"). In
similar fashion to the DT case (commit aa3da644 "of: Add generic device tree
DMA helpers") we introduce helpers to the DMAC drivers which are enumerated by
ACPI.
The proposed extension provides the following API calls:
acpi_dma_controller_register(), devm_acpi_dma_controller_register()
acpi_dma_controller_free(), devm_acpi_dma_controller_free()
acpi_dma_simple_xlate()
acpi_dma_request_slave_chan_by_index()
acpi_dma_request_slave_chan_by_name()
The first two should be used, for example, at probe() and remove() of the
corresponding DMAC driver. At the register stage the DMAC driver supplies a
custom xlate() function to translate a struct dma_spec into struct dma_chan.
Accordingly to the ACPI Fixed DMA resource specification the only two pieces of
information the slave device has are the channel id and the request line (slave
id). Those two are represented by struct dma_spec. The
acpi_dma_request_slave_chan_by_index() provides access to the specifix FixedDMA
resource by its index. Whereas dma_request_slave_channel() takes a string
parameter to identify the DMA resources required by the slave device. To make a
slave device driver work with both DeviceTree and ACPI enumeration a simple
convention is established: "tx" corresponds to the index 0 and "rx" to the
index 1. In case of robust configuration the slave device driver unfortunately
needs to call acpi_dma_request_slave_chan_by_index() directly.
Additionally the patch provides "managed" version of the register/free pair
i.e. devm_acpi_dma_controller_register() and devm_acpi_dma_controller_free().
Usually, the driver uses only devm_acpi_dma_controller_register().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull slave-dmaengine updates from Vinod Koul:
"This is fairly big pull by my standards as I had missed last merge
window. So we have the support for device tree for slave-dmaengine,
large updates to dw_dmac driver from Andy for reusing on different
architectures. Along with this we have fixes on bunch of the drivers"
Fix up trivial conflicts, usually due to #include line movement next to
each other.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (111 commits)
Revert "ARM: SPEAr13xx: Pass DW DMAC platform data from DT"
ARM: dts: pl330: Add #dma-cells for generic dma binding support
DMA: PL330: Register the DMA controller with the generic DMA helpers
DMA: PL330: Add xlate function
DMA: PL330: Add new pl330 filter for DT case.
dma: tegra20-apb-dma: remove unnecessary assignment
edma: do not waste memory for dma_mask
dma: coh901318: set residue only if dma is in progress
dma: coh901318: avoid unbalanced locking
dmaengine.h: remove redundant else keyword
dma: of-dma: protect list write operation by spin_lock
dmaengine: ste_dma40: do not remove descriptors for cyclic transfers
dma: of-dma.c: fix memory leakage
dw_dmac: apply default dma_mask if needed
dmaengine: ioat - fix spare sparse complain
dmaengine: move drivers/of/dma.c -> drivers/dma/of-dma.c
ioatdma: fix race between updating ioat->head and IOAT_COMPLETION_PENDING
dw_dmac: add support for Lynxpoint DMA controllers
dw_dmac: return proper residue value
dw_dmac: fill individual length of descriptor
...
The bestcomm dma hardware, and some of its users like the FEC ethernet
component, is used in different FreeScale parts, including non-powerpc
parts like the ColdFire MCF547x & MCF548x families. Don't keep the
driver hidden in arch/powerpc where it is inaccessible for other arches.
.c files are moved to drivers/dma/bestcomm, while .h files are moved to
include/linux/fsl/bestcomm. Makefiles, Kconfigs and #include directives
are updated for the new file locations.
Tested by recompiling for MPC5200 with all bestcomm users enabled.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
1. virtual channel vs. physical channel
Virtual channel is managed by dmaengine
Physical channel handling resource, such as irq
Physical channel is alloced dynamically as descending priority,
freed immediately when irq done.
The availble highest priority physically channel will alwayes be alloced
Issue pending list -> alloc highest dma physically channel available -> dma done -> free physically channel
2. list: running list & pending list
submit: desc list -> pending list
issue_pending_list: if (IDLE) pending list -> running list; free pending list (RUN)
irq: free running list (IDLE)
check pendlist -> pending list -> running list; free pending list (RUN)
3. irq:
Each list generate one irq, calling callback
One list may contain several desc chain, in such case, make sure only the last desc list generate irq.
4. async
Submit will add desc chain to pending list, which can be multi-called
If multi desc chain is submitted, only the last desc would generate irq -> call back
If IDLE, issue_pending_list start pending_list, transforming pendlist to running list
If RUN, irq will start pending list
5. test
5.1 pxa3xx_nand on pxa910
5.2 insmod dmatest.ko (threads_per_chan=y)
By default drivers/dma/dmatest.c test every channel and test memcpy with 1 threads per channel
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add a DMA engine driver for the TI EDMA controller. This driver
is implemented as a wrapper around the existing DaVinci private
DMA implementation. This approach allows for incremental conversion
of each peripheral driver to the DMA engine API. The EDMA driver
supports slave transfers but does not yet support cyclic transfers.
Signed-off-by: Matt Porter <mporter@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
The shdma driver is going to be split into multiple files. To make this more
convenient move it to an own directory.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Split the virtual slave channel DMA support from the sa11x0 driver so
this code can be shared with other slave DMA engine drivers.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for two-channel dma under dmaengine
support: mmp-adma and pxa910-squ
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add dmaengine based NVIDIA's Tegra APB DMA driver.
This driver support the slave mode of data transfer from
peripheral to memory and vice versa.
The driver supports for the cyclic and non-cyclic mode
of data transfer.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add support for the SA-11x0 DMA driver, which replaces the private
API version in arch/arm/mach-sa1100/dma.c.
We model this as a set of virtual DMA channels, one for each request
signal, and assign the virtual DMA channel to a physical DMA channel
when there is work to be done. This allows DMA users to claim their
channels, and hold them while not in use, without affecting the
availability of the physical channels.
Another advantage over this approach, compared to the private version,
is that a channel can be reconfigured on the fly without having to
release and re-request it - which for the IrDA driver, allows us to
use DMA for SIR mode transmit without eating up three physical
channels. As IrDA is half-duplex, we actually only need one physical
channel, and this architecture allows us to achieve that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[fixed direction enums and cyclic api based on changes
already merged]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The ep93xx DMA controller has 10 independent memory to peripheral (M2P)
channels, and 2 dedicated memory to memory (M2M) channels. M2M channels can
also be used by SPI and IDE to perform DMA transfers to/from their memory
mapped FIFOs.
This driver supports both M2P and M2M channels with DMA_SLAVE, DMA_CYCLIC and
DMA_MEMCPY (M2M only) capabilities.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (66 commits)
avr32: at32ap700x: fix typo in DMA master configuration
dmaengine/dmatest: Pass timeout via module params
dma: let IMX_DMA depend on IMX_HAVE_DMA_V1 instead of an explicit list of SoCs
fsldma: make halt behave nicely on all supported controllers
fsldma: reduce locking during descriptor cleanup
fsldma: support async_tx dependencies and automatic unmapping
fsldma: fix controller lockups
fsldma: minor codingstyle and consistency fixes
fsldma: improve link descriptor debugging
fsldma: use channel name in printk output
fsldma: move related helper functions near each other
dmatest: fix automatic buffer unmap type
drivers, pch_dma: Fix warning when CONFIG_PM=n.
dmaengine/dw_dmac fix: use readl & writel instead of __raw_readl & __raw_writel
avr32: at32ap700x: Specify DMA Flow Controller, Src and Dst msize
dw_dmac: Setting Default Burst length for transfers as 16.
dw_dmac: Allow src/dst msize & flow controller to be configured at runtime
dw_dmac: Changing type of src_master and dest_master to u8.
dw_dmac: Pass Channel Priority from platform_data
dw_dmac: Pass Channel Allocation Order from platform_data
...
Replace EXTRA_CFLAGS with ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
This patch adds dma support for Freescale MXS-based SoC i.MX23/28,
including apbh-dma and apbx-dma.
* apbh-dma and apbx-dma are supported in the driver as two mxs-dma
instances.
* apbh-dma is different between mx23 and mx28, hardware version
register is used to differentiate.
* mxs-dma supports pio function besides data transfer. The driver
uses dma_data_direction DMA_NONE to identify the pio mode, and
steals sgl and sg_len to get pio words and numbers from clients.
* mxs dmaengine has some very specific features, like sense function
and the special NAND support (nand_lock, nand_wait4ready). These
are too specific to implemented in generic dmaengine driver.
* The driver refers to imx-sdma and only a single descriptor is
statically assigned to each channel.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the ccflag-y flag instead of EXTRA_CFLAGS because EXTRA_CFLAGS is
deprecated and should now be switched. According to (documentation/kbuild/makefiles.txt).
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This driver is currently implemented as a user to the old i.MX
DMA API. This allows us to convert each user of the old API to
the dmaengine API one by one. Once this is done the old DMA
driver can be merged into the i.MX dmaengine driver.
V2: remove some debug leftovers and unused variables
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds support for the Freescale i.MX SDMA engine.
The SDMA engine is a scatter/gather DMA engine which is implemented
as a seperate coprocessor. SDMA needs its own firmware which is
requested using the standard request_firmware mechanism. The firmware
has different entry points for each peripheral type, so drivers
have to pass the peripheral type to the DMA engine which in turn
picks the correct firmware entry point from a table contained in
the firmware image itself.
The original Freescale code also supports support for transfering
data to the internal SRAM which needs different entry points to
the firmware. Support for this is currently not implemented. Also,
support for the ASRC (asymmetric sample rate converter) is skipped.
I took a very simple approach to implement dmaengine support. Only
a single descriptor is statically assigned to a each channel. This
means that transfers can't be queued up but only a single transfer
is in progress. This simplifies implementation a lot and is sufficient
for the usual device/memory transfers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Linus Walleij <linus.ml.walleij@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This creates a DMAengine driver for the ARM PL080/PL081 PrimeCells
based on the implementation earlier submitted by Peter Pearse.
This is working like a charm for memcpy and slave DMA to the PL011
PrimeCell on the PB11MPCore.
This DMA controller is used in mostly unmodified form in the ARM
RealView and Versatile platforms, in the ST-Ericsson Nomadik, and
in the ST SPEAr platform.
It has been converted to use the header from the Samsung PL080
derivate instead of its own defintions. The Samsungs have a custom
driver in their mach-* folders though, atleast we can share the
register definitions.
Cc: Peter Pearse <peter.pearse@arm.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[GFP_KERNEL to GFP_NOWAIT in pl08x_prep_dma_memcpy]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Topcliff PCH is the platform controller hub that is going to
be used in Intel's upcoming general embedded platforms. This
adds the driver for Topcliff PCH DMA controller. The DMA
channels are strictly for device to host or host to device
transfers and cannot be used for generic memcpy.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
[kill GFP_ATOMIC, kill __raw_{read|write}l, locking fixlet]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch add DMA drivers for DMA controllers in Langwell chipset
of Intel(R) Moorestown platform and DMA controllers in Penwell of
Intel(R) Medfield platfrom
This patch adds support for Moorestown DMAC1 and DMAC2 controllers.
It also add support for Medfiled GP DMA and DMAC1 controllers.
These controllers supports memory to peripheral and peripheral to
memory transfers. It support only single block transfers.
This driver is based on Kernel DMA engine
Anyone who wishes to use this controller should use DMA engine APIs
This controller exposes DMA_SLAVE capabilities and notifies the client drivers
of DMA transaction completion
Config option required to be enabled CONFIG_INTEL_MID_DMAC=y
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add DMA Engine API driver for the PL330 DMAC.
This driver is supposed to be reusable by various
platforms that have one or more PL330 DMACs.
Atm, DMA_SLAVE and DMA_MEMCPY capabilities have been
implemented.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@stericsson.com>
[dan.j.williams@intel.com: missing slab.h and ->device_control() fixups]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is a straightforward driver for the ST-Ericsson DMA40 DMA
controller found in U8500, implemented akin to the existing
COH 901 318 driver.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidh Kasagar <srinidhi.kasagar@stericsson.com>
Cc: STEricsson_nomadik_linux@list.st.com
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adds the support for the DMA engine withing the timberdale FPGA.
The DMA channels are strict device to host, or host to device
and can not be used for generic memcpy.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Adds initial version of MPC512x DMA driver.
Only memory to memory transfers are currenly supported.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This adds Kconfig options for DEBUG and VERBOSE_DEBUG to the DMA
engine subsystem, I got tired of editing the Makefile manually
each time I want to debug things in here, modelled this on the
debug switches for other subsystems and works like a charm when
working on our DMA engines.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds new version of the PPC440SPe ADMA driver.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds support for the ST-Ericsson COH 901 318 DMA block,
found in the U300 series platforms. It registers a DMA slave for
device I/O and also a memcpy slave for memcpy.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This supported all DMA channels, and it was tested in SH7722,
SH7780, SH7785 and SH7763.
This can not use with SH DMA API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When first created the ioat driver was the only inhabitant of
drivers/dma/. Now, it is the only multi-file (more than a .c and a .h)
driver in the directory. Moving it to an ioat/ subdirectory allows the
naming convention to be cleaned up, and allows for future splitting of
the source files by hardware version (v1, v2, and v3).
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.
This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip. On other products, it will be used
also for peripheral DMA transfer (slave API support to come).
I used dmatest client without problem in different configurations to test it.
Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds support for the integrated DMAC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
i.MX3x SoCs contain an Image Processing Unit, consisting of a Control
Module (CM), Display Interface (DI), Synchronous Display Controller (SDC),
Asynchronous Display Controller (ADC), Image Converter (IC), Post-Filter
(PF), Camera Sensor Interface (CSI), and an Image DMA Controller (IDMAC).
CM contains, among other blocks, an Interrupt Generator (IG) and a Clock
and Reset Control Unit (CRCU). This driver serves IDMAC and IG. They are
supported over dmaengine and irq-chip APIs respectively.
IDMAC is a specialised DMA controller, its DMA channels cannot be used for
general-purpose operations, even though it might be possible to configure
a memory-to-memory channel for memcpy operation. This driver will not work
with generic dmaengine clients, clients, wishing to use it must use
respective wrapper structures, they also must specify which channels they
require, as channels are hard-wired to specific IPU functions.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Andy Gross
Jonas Jensen
Florian Meier
Heiko Stuebner
Linus Torvalds
Zhangfei Gao
Sebastian Andrzej Siewior
Lars-Peter Clausen
Andy Shevchenko
Shimoda, Yoshihiro
Vinod Koul
Philippe De Muyter
Zhangfei Gao
Matt Porter
Russell King
Guennadi Liakhovetski
Laxman Dewangan
Rongjun Ying
Mika Westerberg
matt mooney
Shawn Guo
Tracey Dent
Dan Williams
Sascha Hauer
Linus Walleij
Yong Wang
Jassi Brar
Richard Röjfors
Piotr Ziecik
Anatolij Gustschin
Nobuhiro Iwamatsu
Nicolas Ferre
Atsushi Nemoto
Guennadi Liakhovetski