This is necessary for use with the upcoming "mv_qc_issue_fis()" patch,
but is being added separately here for easier code review.
When using command issue via the "mv_qc_issue_fis()" mechanism,
the initial ATA_BUSY bit does not show in the ATA status (shadow) register.
This can confuse libata! So here we add a hook to fake ATA_BUSY
for that situation, until the first time a BUSY, DRQ, or ERR bit is seen.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
so that it doesn't miss any protocols. Handle future cases where a
qc is specially marked for polled issue or where a particular chip
version prefers interrupts over polling for PIO.
This mimics the polling decision logic from ata_sff_qc_issue().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This also gets rid of any need for mv_mode_filter().
Using basic DMA on GEN_IIE requires setting an undocumented
bit in an undocumented register. For safety, we clear that
bit again when switching back to EDMA mode.
To avoid a performance penalty when switching modes,
we cache the register in port_priv, as already done for other regs.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Maintain a local (mv_port_priv) cache of frequently accessed registers,
to avoid having to re-read them (very slow) on every transistion
between EDMA and non-EDMA modes. This speeds up things like
flushing the drive write cache, and anything using basic DMA transfers.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no need to turn off intx explicitly on msi enable. This is
automatically handled by pci. Drop it.
This might be needed on machines if the BIOS turns intx off during
boot. However, there's no evidence of such behavior for ahci and
the only such case seems to be ICH5 PATA according to ata_piix.
Also, given the way ahci operates, it's highly unlikely BIOS ever
disables IRQ for the controller. However, as this change has slight
possibility of introducing failure, please schedule it for #upstream.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I'm not quite sure what freezing and thawing is used for. Tests showed
that the port is being frozen at initialisation state and thawed right
afterwards, then the functions were not called anymore. Dropping the
complete custom code for handling the frozen state seems to work at
least for a standard use case including mounting a partition, copying
some files in it (in parallel) and finally removing them and unmounting
the partition.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The biggest difference between rb532_pata_data_xfer() and
ata_sff_data_xfer32() is the call to ata_sff_pause() at the end of
rb532_pata_data_xfer() which I suppose to be unnecessary since it works
without. I've also tested using ata_sff_data_xfer() as replacement, but
since we know that the driver supports 32bit IO, using the optimised
version should be safe.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The only difference between rb532_pata_exec_command() and
ata_sff_exec_command() is added debugging output, so it can be dropped
and the standard op used instead.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since the delay used internally is just the same as ata_sff_pause()
uses, rb532_pata_finish_io() does exactly the same as ata_sff_pause()
and thus can be replaced by the later one.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove redundant code left over from the earlier patch 04/07.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Try and avoid unnecessary reconfiguration of the EDMA config register
on every single non-EDMA I/O operation, by moving the call to
mv_edma_cfg() into mv_stop_edma(). It must then also be invoked
from mv_hardreset() and from mv_port_start().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ATAPI support to sata_mv, using sff DMA for GEN_II chipsets,
and plain old PIO for GEN_IIE.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix mv_fill_sg() to zero out the reserved word (required for ATAPI),
and to include a memory barrier. This may also help with problems
reported by Jens on the PPC platform.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update the logic in ata_qc_from_tag() to match that used
in similar places elsewhere in libata.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange logic in mv_qc_issue() to handle protocols
other than ATA_PROT_DMA, ATA_PROT_NCQ, and ATA_PROT_PIO.
This is in preparation for later enabling ATAPI support.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rearrange mv_start_dma() and friends, in preparation for adding
non-EDMA DMA modes, and non-EDMA interrupts, to the driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clean up the chipset GENeration FLAGS, and rename them
for consistency with other uses of GEN_XX within sata_mv.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With a sufficiently new compiler and binutils, code which wasn't
previously generating .eh_frame sections has begun to. Certain
architectures (powerpc, in this case) may generate unexpected relocation
formats in response to this, preventing modules from loading.
While the new relocation types should probably be handled, revert to the
previous behaviour with regards to generation of .eh_frame sections.
(This was reported against Fedora, which appears to be the only distro
doing any building against gcc-4.4 at present: RH bz#486545.)
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Alexandre Oliva <aoliva@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert the change to the orphan dates of Windows 95, DOS, compression.
Add a new orphan date for OS/2.
Signed-off-by: Jody McIntyre <scjody@sun.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
ucc_geth: Fix oops when using fixed-link support
dm9000: locking bugfix
net: update dnet.c for bus_id removal
dnet: DNET should depend on HAS_IOMEM
dca: add missing copyright/license headers
nl80211: Check that function pointer != NULL before using it
sungem: missing net_device_ops
be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle
be2net: replenish when posting to rx-queue is starved in out of mem conditions
bas_gigaset: correctly allocate USB interrupt transfer buffer
smsc911x: reset last known duplex and carrier on open
sh_eth: Fix mistake of the address of SH7763
sh_eth: Change handling of IRQ
netns: oops in ip[6]_frag_reasm incrementing stats
net: kfree(napi->skb) => kfree_skb
net: fix sctp breakage
ipv6: fix display of local and remote sit endpoints
net: Document /proc/sys/net/core/netdev_budget
tulip: fix crash on iface up with shirq debug
virtio_net: Make virtio_net support carrier detection
...
This patch fixes bug #12208:
Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=12208
Subject : uml is very slow on 2.6.28 host
This turned out to be not a scheduler regression, but an already
existing problem in ptrace being triggered by subtle scheduler
changes.
The problem is this:
- task A is ptracing task B
- task B stops on a trace event
- task A is woken up and preempts task B
- task A calls ptrace on task B, which does ptrace_check_attach()
- this calls wait_task_inactive(), which sees that task B is still on the runq
- task A goes to sleep for a jiffy
- ...
Since UML does lots of the above sequences, those jiffies quickly add
up to make it slow as hell.
This patch solves this by not rescheduling in read_unlock() after
ptrace_stop() has woken up the tracer.
Thanks to Oleg Nesterov and Ingo Molnar for the feedback.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Grant picked up the wrong version of "Respect _PAGE_COHERENT on classic
ppc32 SW" (commit a4bd6a93c3)
It was missing the code to actually deal with the fixup of
_PAGE_COHERENT based on the CPU feature.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit b1c4a9dddf ("ucc_geth: Change
uec phy id to the same format as gianfar's") introduced a regression
in the ucc_geth driver that causes this oops when fixed-link is used:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0151270
Oops: Kernel access of bad area, sig: 11 [#1]
TMCUTU
NIP: c0151270 LR: c0151270 CTR: c0017760
REGS: cf81fa60 TRAP: 0300 Not tainted (2.6.29-rc8)
MSR: 00009032 <EE,ME,IR,DR> CR: 24024042 XER: 20000000
DAR: 00000000, DSISR: 20000000
TASK = cf81cba0[1] 'swapper' THREAD: cf81e000
GPR00: c0151270 cf81fb10 cf81cba0 00000000 c0272e20 c025f354 00001e80
cf86b08c
GPR08: d1068200 cffffb74 06000000 d106c200 42024042 10085148 0fffd000
0ffc81a0
GPR16: 00000001 00000001 00000000 007ffeb0 00000000 0000c000 cf83f36c
cf83f000
GPR24: 00000030 cf83f360 cf81fb20 00000000 d106c200 20000000 00001e80
cf83f360
NIP [c0151270] ucc_geth_open+0x330/0x1efc
LR [c0151270] ucc_geth_open+0x330/0x1efc
Call Trace:
[cf81fb10] [c0151270] ucc_geth_open+0x330/0x1efc (unreliable)
[cf81fba0] [c0187638] dev_open+0xbc/0x12c
[cf81fbc0] [c0187e38] dev_change_flags+0x8c/0x1b0
This patch fixes the issue by removing offending (and somewhat
duplicate) code from init_phy() routine, and changes _probe()
function to use uec_mdio_bus_name().
Also, since we fully construct phy_bus_id in the _probe() routine,
we no longer need ->phy_address and ->mdio_bus fields in
ucc_geth_info structure.
I wish the patch would be a bit shorter, but it seems like the only
way to fix the issue in a sane way. Luckily, the patch has been
tested with real PHYs and fixed-link, so no further regressions
expected.
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a locking bug in the dm9000 driver. It calls
request_irq() without setting IRQF_DISABLED ... which is
correct for handlers that support IRQ sharing, since that
behavior is not guaranteed for shared IRQs. However, its
IRQ handler then wrongly assumes that IRQs are blocked.
So the fix just uses the right spinlock primitives in the
IRQ handler.
NOTE: this is a classic example of the type of bug which
lockdep currently masks by forcibly setting IRQF_DISABLED
on IRQ handlers that did not request that flag.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'fix-includes' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: merge the non-MMU and MMU versions of siginfo.h
m68k: use the MMU version of unistd.h for all m68k platforms
m68k: merge the non-MMU and MMU versions of signal.h
m68k: merge the non-MMU and MMU versions of ptrace.h
m68k: use MMU version of setup.h for both MMU and non-MMU
m68k: merge the non-MMU and MMU versions of sigcontext.h
m68k: merge the non-MMU and MMU versions of swab.h
m68k: merge the non-MMU and MMU versions of param.h
Update all previous incarnations of my email address to the correct one.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If ecryptfs_encrypted_view or ecryptfs_xattr_metadata were being
specified as mount options, a NULL pointer dereference of crypt_stat
was possible during lookup.
This patch moves the crypt_stat assignment into
ecryptfs_lookup_and_interpose_lower(), ensuring that crypt_stat
will not be NULL before we attempt to dereference it.
Thanks to Dan Carpenter and his static analysis tool, smatch, for
finding this bug.
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Acked-by: Dustin Kirkland <kirkland@canonical.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When allocating the memory used to store the eCryptfs header contents, a
single, zeroed page was being allocated with get_zeroed_page().
However, the size of an eCryptfs header is either PAGE_CACHE_SIZE or
ECRYPTFS_MINIMUM_HEADER_EXTENT_SIZE (8192), whichever is larger, and is
stored in the file's private_data->crypt_stat->num_header_bytes_at_front
field.
ecryptfs_write_metadata_to_contents() was using
num_header_bytes_at_front to decide how many bytes should be written to
the lower filesystem for the file header. Unfortunately, at least 8K
was being written from the page, despite the chance of the single,
zeroed page being smaller than 8K. This resulted in random areas of
kernel memory being written between the 0x1000 and 0x1FFF bytes offsets
in the eCryptfs file headers if PAGE_SIZE was 4K.
This patch allocates a variable number of pages, calculated with
num_header_bytes_at_front, and passes the number of allocated pages
along to ecryptfs_write_metadata_to_contents().
Thanks to Florian Streibelt for reporting the data leak and working with
me to find the problem. 2.6.28 is the only kernel release with this
vulnerability. Corresponds to CVE-2009-0787
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Acked-by: Dustin Kirkland <kirkland@canonical.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Eugene Teo <eugeneteo@kernel.sg>
Cc: Greg KH <greg@kroah.com>
Cc: dann frazier <dannf@dannf.org>
Cc: Serge E. Hallyn <serue@us.ibm.com>
Cc: Florian Streibelt <florian@f-streibelt.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a regression introduced when we switched to using the core
pci_set_power_state(). The chip seems to need the state to be written
over and over again until it sticks, so we do that.
Note that the code is a bit blunt, without timeout, etc... but that's
pretty much because I put back in there the code exactly as it used to
be before the regression. I still add a call to pci_set_power_state()
at the end so that ACPI gets called appropriately on x86.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Raymond Wooninck <tittiatcoke@gmail.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In two dca files copyright and license headers are missing.
This patch adds them there.
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NL80211_CMD_GET_MESH_PARAMS and NL80211_CMD_SET_MESH_PARAMS handlers
did not verify whether a function pointer is NULL (not supported by
the driver) before trying to call the function. The former nl80211
command is available for unprivileged users, too, so this can
potentially allow normal users to kill networking (or worse..) if
mac80211 is built without CONFIG_MAC80211_MESH=y.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sungem driver only got partially converted to net_device_ops.
Since this could cause bugs, please push this to 2.6.29
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to reconfigure vlan-ids during an i/f down/up cycle
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to replenish the rx-queue when it is in a starved
state (due to out-of-mem conditions)
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The libaio test harness turned up a problem whereby lookup_ioctx on a
bogus io context was returning the 1 valid io context from the list
(harness/cases/3.p).
Because of that, an extra put_iocontext was done, and when the process
exited, it hit a BUG_ON in the put_iocontext macro called from exit_aio
(since we expect a users count of 1 and instead get 0).
The problem was introduced by "aio: make the lookup_ioctx() lockless"
(commit abf137dd77).
Thanks to Zach for pointing out that hlist_for_each_entry_rcu will not
return with a NULL tpos at the end of the loop, even if the entry was
not found.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Zach Brown <zach.brown@oracle.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove a source of fput() call from inside IRQ context. Myself, like Eric,
wasn't able to reproduce an fput() call from IRQ context, but Jeff said he was
able to, with the attached test program. Independently from this, the bug is
conceptually there, so we might be better off fixing it. This patch adds an
optimization similar to the one we already do on ->ki_filp, on ->ki_eventfd.
Playing with ->f_count directly is not pretty in general, but the alternative
here would be to add a brand new delayed fput() infrastructure, that I'm not
sure is worth it.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sam Ravnborg says:
"We have several architectures that plays strange games with $(CC) and
$(CROSS_COMPILE).
So we need to postpone any use of $(call cc-option..) until we have
included the arch specific Makefile so we try with the correct $(CC)
version."
Requested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] make page table upgrade work again
[S390] make page table walking more robust
[S390] Dont check for pfn_valid() in uaccess_pt.c
[S390] ftrace/mcount: fix kernel stack backchain
[S390] topology: define SD_MC_INIT to fix performance regression
[S390] __div64_31 broken for CONFIG_MARCH_G5
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: Clear space_info full when adding new devices
Btrfs: Fix locking around adding new space_info
Nick Piggin noticed this (very unlikely) race between setting a page
dirty and creating the buffers for it - we need to hold the mapping
private_lock until we've set the page dirty bit in order to make sure
that create_empty_buffers() might not build up a set of buffers without
the dirty bits set when the page is dirty.
I doubt anybody has ever hit this race (and it didn't solve the issue
Nick was looking at), but as Nick says: "Still, it does appear to solve
a real race, which we should close."
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes sure that gcc doesn't try to optimize away wrapping
arithmetic, which the kernel occasionally uses for overflow testing, ie
things like
if (ptr + offset < ptr)
which technically is undefined for non-unsigned types. See
http://bugzilla.kernel.org/show_bug.cgi?id=12597
for details.
Not all versions of gcc support it, so we need to make it conditional
(it looks like it was introduced in gcc-3.4).
Reminded-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Lord
Tejun Heo
Phil Sutter
Mark Lord
Linus Torvalds
Kyle McMartin
Jody McIntyre
Miklos Szeredi
Kumar Gala
Anton Vorontsov
David Brownell
Stephen Rothwell
Gertjan van Wingerde
Tyler Hicks
Benjamin Herrenschmidt
Ilya Yanok
Maciej Sosnowski
David S. Miller
Jouni Malinen
Stephen Hemminger
Sathya Perla
Jeff Moyer
Davide Libenzi