Граф коммитов

57331 Коммитов

Автор SHA1 Сообщение Дата
Mark Lord 1a660164c2 [libata] Export ata_pio_queue_task() so that it can be used from sata_mv.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:41 -04:00
Mark Lord d16ab3f633 [libata] sata_mv: Add a new mv_sff_check_status() function to sata_mv.
This is necessary for use with the upcoming "mv_qc_issue_fis()" patch,
but is being added separately here for easier code review.

When using command issue via the "mv_qc_issue_fis()" mechanism,
the initial ATA_BUSY bit does not show in the ATA status (shadow) register.
This can confuse libata!  So here we add a hook to fake ATA_BUSY
for that situation, until the first time a BUSY, DRQ, or ERR bit is seen.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:41 -04:00
Mark Lord 42ed893d80 [libata] sata_mv: Tighten up interrupt masking in mv_qc_issue()
so that it doesn't miss any protocols.  Handle future cases where a
qc is specially marked for polled issue or where a particular chip
version prefers interrupts over polling for PIO.

This mimics the polling decision logic from ata_sff_qc_issue().

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:40 -04:00
Mark Lord c01e8a2312 [libata] sata_mv: Enable use of (basic) DMA for ATAPI on GEN_IIE chips
This also gets rid of any need for mv_mode_filter().

Using basic DMA on GEN_IIE requires setting an undocumented
bit in an undocumented register.  For safety, we clear that
bit again when switching back to EDMA mode.

To avoid a performance penalty when switching modes,
we cache the register in port_priv, as already done for other regs.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:40 -04:00
Mark Lord 08da175937 [libata] sata_mv: cache frequently-accessed registers
Maintain a local (mv_port_priv) cache of frequently accessed registers,
to avoid having to re-read them (very slow) on every transistion
between EDMA and non-EDMA modes.  This speeds up things like
flushing the drive write cache, and anything using basic DMA transfers.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:40 -04:00
Tejun Heo a5bfc4714b ahci: drop intx manipulation on msi enable
There's no need to turn off intx explicitly on msi enable.  This is
automatically handled by pci.  Drop it.

This might be needed on machines if the BIOS turns intx off during
boot.  However, there's no evidence of such behavior for ahci and
the only such case seems to be ICH5 PATA according to ata_piix.
Also, given the way ahci operates, it's highly unlikely BIOS ever
disables IRQ for the controller.  However, as this change has slight
possibility of introducing failure, please schedule it for #upstream.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:40 -04:00
Phil Sutter 6be976e79d pata-rb532-cf: drop custom freeze and thaw
I'm not quite sure what freezing and thawing is used for. Tests showed
that the port is being frozen at initialisation state and thawed right
afterwards, then the functions were not called anymore. Dropping the
complete custom code for handling the frozen state seems to work at
least for a standard use case including mounting a partition, copying
some files in it (in parallel) and finally removing them and unmounting
the partition.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:40 -04:00
Phil Sutter 180bd147f1 pata-rb532-cf: use ata_sff_data_xfer32()
The biggest difference between rb532_pata_data_xfer() and
ata_sff_data_xfer32() is the call to ata_sff_pause() at the end of
rb532_pata_data_xfer() which I suppose to be unnecessary since it works
without. I've also tested using ata_sff_data_xfer() as replacement, but
since we know that the driver supports 32bit IO, using the optimised
version should be safe.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:39 -04:00
Phil Sutter bff9ad3c4c pata-rb532-cf: use ata_sff_exec_command()
The only difference between rb532_pata_exec_command() and
ata_sff_exec_command() is added debugging output, so it can be dropped
and the standard op used instead.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:39 -04:00
Phil Sutter 96b34ce7ca pata-rb532-cf: replace rb532_pata_finish_io()
Since the delay used internally is just the same as ata_sff_pause()
uses, rb532_pata_finish_io() does exactly the same as ata_sff_pause()
and thus can be replaced by the later one.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:39 -04:00
Mark Lord 84bcbeebcf sata_mv: remove leftovers
Remove redundant code left over from the earlier patch 04/07.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:39 -04:00
Mark Lord 66e57a2cb0 sata_mv: optimize use of mv_edma_cfg
Try and avoid unnecessary reconfiguration of the EDMA config register
on every single non-EDMA I/O operation, by moving the call to
mv_edma_cfg() into mv_stop_edma().  It must then also be invoked
from mv_hardreset() and from mv_port_start().

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:38 -04:00
Mark Lord da14265e77 sata_mv: introduce support for ATAPI devices
Add ATAPI support to sata_mv, using sff DMA for GEN_II chipsets,
and plain old PIO for GEN_IIE.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:38 -04:00
Mark Lord 32cd11a610 sata_mv: mv_fill_sg fixes v2
Fix mv_fill_sg() to zero out the reserved word (required for ATAPI),
and to include a memory barrier.  This may also help with problems
reported by Jens on the PPC platform.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:38 -04:00
Mark Lord 95db505125 sata_mv: update ata_qc_from_tag
Update the logic in ata_qc_from_tag() to match that used
in similar places elsewhere in libata.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:38 -04:00
Mark Lord f48765ccb4 sata_mv: restructure mv_qc_issue
Rearrange logic in mv_qc_issue() to handle protocols
other than ATA_PROT_DMA, ATA_PROT_NCQ, and ATA_PROT_PIO.
This is in preparation for later enabling ATAPI support.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:38 -04:00
Mark Lord 00b81235aa sata_mv: rearrange mv_start_dma() and friends
Rearrange mv_start_dma() and friends, in preparation for adding
non-EDMA DMA modes, and non-EDMA interrupts, to the driver.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:38 -04:00
Mark Lord 91b1a84c10 sata_mv: cleanup chipset GENeration FLAGS
Clean up the chipset GENeration FLAGS, and rename them
for consistency with other uses of GEN_XX within sata_mv.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:02:38 -04:00
Linus Torvalds d56ffd38a9 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
  ucc_geth: Fix oops when using fixed-link support
  dm9000: locking bugfix
  net: update dnet.c for bus_id removal
  dnet: DNET should depend on HAS_IOMEM
  dca: add missing copyright/license headers
  nl80211: Check that function pointer != NULL before using it
  sungem: missing net_device_ops
  be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle
  be2net: replenish when posting to rx-queue is starved in out of mem conditions
  bas_gigaset: correctly allocate USB interrupt transfer buffer
  smsc911x: reset last known duplex and carrier on open
  sh_eth: Fix mistake of the address of SH7763
  sh_eth: Change handling of IRQ
  netns: oops in ip[6]_frag_reasm incrementing stats
  net: kfree(napi->skb) => kfree_skb
  net: fix sctp breakage
  ipv6: fix display of local and remote sit endpoints
  net: Document /proc/sys/net/core/netdev_budget
  tulip: fix crash on iface up with shirq debug
  virtio_net: Make virtio_net support carrier detection
  ...
2009-03-23 09:25:58 -07:00
Linus Torvalds 12a37b5e2c Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix crash with /proc/iomem
  sparc64: Reschedule KGDB capture to a software interrupt.
  sbus: Auto-load openprom module when device opened.
2009-03-23 09:25:24 -07:00
Anton Vorontsov 61fa9dcf93 ucc_geth: Fix oops when using fixed-link support
commit b1c4a9dddf ("ucc_geth: Change
uec phy id to the same format as gianfar's") introduced a regression
in the ucc_geth driver that causes this oops when fixed-link is used:

Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc0151270
Oops: Kernel access of bad area, sig: 11 [#1]
TMCUTU
NIP: c0151270 LR: c0151270 CTR: c0017760
REGS: cf81fa60 TRAP: 0300   Not tainted  (2.6.29-rc8)
MSR: 00009032 <EE,ME,IR,DR>  CR: 24024042  XER: 20000000
DAR: 00000000, DSISR: 20000000
TASK = cf81cba0[1] 'swapper' THREAD: cf81e000
GPR00: c0151270 cf81fb10 cf81cba0 00000000 c0272e20 c025f354 00001e80
cf86b08c
GPR08: d1068200 cffffb74 06000000 d106c200 42024042 10085148 0fffd000
0ffc81a0
GPR16: 00000001 00000001 00000000 007ffeb0 00000000 0000c000 cf83f36c
cf83f000
GPR24: 00000030 cf83f360 cf81fb20 00000000 d106c200 20000000 00001e80
cf83f360
NIP [c0151270] ucc_geth_open+0x330/0x1efc
LR [c0151270] ucc_geth_open+0x330/0x1efc
Call Trace:
[cf81fb10] [c0151270] ucc_geth_open+0x330/0x1efc (unreliable)
[cf81fba0] [c0187638] dev_open+0xbc/0x12c
[cf81fbc0] [c0187e38] dev_change_flags+0x8c/0x1b0

This patch fixes the issue by removing offending (and somewhat
duplicate) code from init_phy() routine, and changes _probe()
function to use uec_mdio_bus_name().

Also, since we fully construct phy_bus_id in the _probe() routine,
we no longer need ->phy_address and ->mdio_bus fields in
ucc_geth_info structure.

I wish the patch would be a bit shorter, but it seems like the only
way to fix the issue in a sane way. Luckily, the patch has been
tested with real PHYs and fixed-link, so no further regressions
expected.

Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22 21:30:52 -07:00
David Brownell e3162d381f dm9000: locking bugfix
This fixes a locking bug in the dm9000 driver.  It calls
request_irq() without setting IRQF_DISABLED ... which is
correct for handlers that support IRQ sharing, since that
behavior is not guaranteed for shared IRQs.  However, its
IRQ handler then wrongly assumes that IRQs are blocked.
So the fix just uses the right spinlock primitives in the
IRQ handler.

NOTE:  this is a classic example of the type of bug which
lockdep currently masks by forcibly setting IRQF_DISABLED
on IRQ handlers that did not request that flag.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22 21:28:39 -07:00
Stephen Rothwell 6580f57d48 net: update dnet.c for bus_id removal
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-22 21:22:48 -07:00
Benjamin Herrenschmidt 18a0d89e54 radeonfb: Whack the PCI PM register until it sticks
This fixes a regression introduced when we switched to using the core
pci_set_power_state().  The chip seems to need the state to be written
over and over again until it sticks, so we do that.

Note that the code is a bit blunt, without timeout, etc...  but that's
pretty much because I put back in there the code exactly as it used to
be before the regression.  I still add a call to pci_set_power_state()
at the end so that ACPI gets called appropriately on x86.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Raymond Wooninck <tittiatcoke@gmail.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-22 11:08:53 -07:00
Ilya Yanok 4b97926ddf dnet: DNET should depend on HAS_IOMEM
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 16:58:47 -07:00
Maciej Sosnowski e2fc4d1929 dca: add missing copyright/license headers
In two dca files copyright and license headers are missing.
This patch adds them there.

Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 13:31:23 -07:00
Stephen Hemminger 5ed0102fbf sungem: missing net_device_ops
Sungem driver only got partially converted to net_device_ops.
Since this could cause bugs, please push this to 2.6.29

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19 23:58:01 -07:00
Sathya Perla 1ab1ab7543 be2net: fix to restore vlan ids into BE2 during a IF DOWN->UP cycle
This is a patch to reconfigure vlan-ids during an i/f down/up cycle

Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19 23:56:46 -07:00
Sathya Perla ea1dae11e0 be2net: replenish when posting to rx-queue is starved in out of mem conditions
This is a patch to replenish the rx-queue when it is in a starved
state (due to out-of-mem conditions)

Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-19 23:56:20 -07:00
Linus Torvalds 2d8620cb88 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: fix waitqueue usage in hiddev
  HID: fix incorrect free in hiddev
2009-03-19 14:50:15 -07:00
David S. Miller 0702b30dd8 Merge branch 'master' of /home/davem/src/GIT/linux-2.6/ 2009-03-18 23:53:57 -07:00
Tilman Schmidt 170ebf8516 bas_gigaset: correctly allocate USB interrupt transfer buffer
Every USB transfer buffer has to be allocated individually by kmalloc.

Impact: bugfix, no functional change

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Tested-by: Kolja Waschk <kawk@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18 23:44:23 -07:00
Steve Glendinning 44c1d6f99d smsc911x: reset last known duplex and carrier on open
smsc911x_phy_adjust_link is called periodically by the phy layer (as
it's run in polling mode), and it only updates the hardware when it sees
a change in duplex or carrier.  This patch clears the last known values
every time the interface is brought up, instead of only when the module
is loaded.

Without this patch the adjust_link function never updates the hardware
after an ifconfig down; ifconfig up.  On a full duplex link this causes
the tx error counter to increment, even though packets are correctly
transmitted, as the default MAC_CR register setting is for half duplex.

The tx errors are "no carrier" errors, which should be ignored in
full-duplex mode.  When MAC_CR is set to "full duplex" mode they are
correctly ignored by the hardware.

Note that even with this patch the tx error counter can increment if
packets are transmitted between "ifconfig up" and the first phy poll
interval.  An improved solution would use the phy interrupt with phylib,
but I haven't managed to make this work 100% robustly yet.

Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18 23:37:18 -07:00
Nobuhiro Iwamatsu 2e2a6a9f71 sh_eth: Fix mistake of the address of SH7763
Address of SH_TSU_ADDR and ARSTR of SH7763 was wrong.
This revise it.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18 23:31:50 -07:00
Nobuhiro Iwamatsu 0e0fde3c8d sh_eth: Change handling of IRQ
Handling of IRQ of the SH7763/SH7764 CPU which sh_eth supported was
changed.
This revises it for this change.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18 23:31:49 -07:00
Kyle McMartin 69145635d4 tulip: fix crash on iface up with shirq debug
Tulip is currently doing request_irq before it has done its
initialization. This is usually not a problem because it hasn't
enable interrupts yet, but with DEBUG_SHIRQ on, we call the irq handler
when registering the interrupt as a sanity check.

This can result in a NULL ptr dereference, so call tulip_init_ring
before request_irq, and add a free_ring function to do the freeing
now shared with tulip_close.

Tested with a shell loop running ifup, ifdown in a loop a few hundred
times with DEBUG_SHIRQ on.

Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18 18:49:01 -07:00
Pantelis Koukousoulas 4783256ef9 virtio_net: Make virtio_net support carrier detection
Impact: Make NetworkManager work with virtio_net

For now the semantics are simple: There is always carrier.

This allows a seamless experience with e.g., qemu/kvm
where NetworkManager just configures and sets up
everything automagically.

If/when a generally agreed-upon way to control
carrier on/off in the emulator/hypervisor level
emerges, it will be trivial to extend the driver
to support that too, but for now even this 2-liner
makes user experience that much better.

Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18 18:40:02 -07:00
Jay Vosburgh 17d04500e2 bonding: Fix updating of speed/duplex changes
This patch corrects an omission from the following commit:

commit f0c76d6177
Author: Jay Vosburgh <fubar@us.ibm.com>
Date:   Wed Jul 2 18:21:58 2008 -0700

    bonding: refactor mii monitor

	The un-refactored code checked the link speed and duplex of
every slave on every pass; the refactored code did not do so.

	The 802.3ad and balance-alb/tlb modes utilize the speed and
duplex information, and require it to be kept up to date.  This patch
adds a notifier check to perform the appropriate updating when the slave
device speed changes.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18 18:38:25 -07:00
Michael Chan 6901031372 bnx2: Fix problem of using wrong IRQ handler.
The MSI-X handler was chosen before the call to pci_enable_msix().
If MSI-X was not available, the wrong MSI-X handler would be used in
INTA mode.  This would cause a screaming interrupt problem because
INTA would not be cleared by the MSI-X handler.

Fixed by assigning MSI-X handler after pci_enable_msix() returns
successfully.  Also update version to 1.9.3.

Thomas Chenault <thomas_chenault@dell.com> helped us find this problem.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-18 18:11:51 -07:00
Linus Torvalds a1e4ee2286 Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: benet: remove driver now that it is merged in drivers/net/
2009-03-18 09:34:17 -07:00
Greg Kroah-Hartman d0573facf2 Staging: benet: remove driver now that it is merged in drivers/net/
The benet driver is now in the proper place in drivers/net/benet, so we
can remove the staging version.

Acked-by: Sathya Perla <sathyap@serverengines.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-18 09:22:17 -07:00
Linus Torvalds d941d0ed6b Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/ps3: ps3_defconfig updates
  powerpc/mm: Respect _PAGE_COHERENT on classic ppc32 SW
  powerpc/5200: Enable CPU_FTR_NEED_COHERENT for MPC52xx
  ps3/block: Replace mtd/ps3vram by block/ps3vram
2009-03-18 09:05:40 -07:00
Benjamin Herrenschmidt c71327ad9f Merge commit 'gcl/merge' into merge 2009-03-18 13:16:30 +11:00
Thomas Bartosik 8a0845c51b USB: storage: Unusual USB device Prolific 2507 variation added
The "c-enter" USB to Toshiba 1.8" IDE enclosure needs special treatment
to work flawlessly. This patch is absolutely trivial, as the integrated
USB-IDE bridge is already identified to be an "unusual" device, only the
bcdDevice is different (lower) to the bcdDeviceMin already included in
the kernel.
It is a Prolific 2507 bridge.

T:  Bus=02 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=067b ProdID=2507 Rev= 0.01
S:  Manufacturer=Prolific Technology Inc.
S:  Product=ATAPI-6 Bridge Controller
S:  SerialNumber=00000272
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms


Signed-off-by: Thomas Bartosik <tbartdev@gmx-topmail.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17 14:01:29 -07:00
Achilleas Kotsis e7f2f0d77a USB: Add device id for Option GTM380 to option driver
Option GTM380 in Modem mode uses Product ID 0x7201. This has been tested and works
on production systems for over 6 months.

Signed-off-by: Achilleas Kotsis <akots@exponent.gr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17 14:01:29 -07:00
Dirk Hohndel 56a2182743 USB: Add Vendor/Product ID for new CDMA U727 to option driver
* newer versions of the Novatel Wireless U727 CDMA 3G USB stick
   have a different Product ID (0x5010); adding this ID makes them
   work just fine with the option driver

Signed-off-by: Dirk Hohndel <hohndel@infradead.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17 14:01:29 -07:00
Moritz Muehlenhoff 716a9c8561 USB: Updated unusual-devs entry for USB mass storage on Nokia 6233
Current firmware revision 5.60 still behaves the same,
so update the quirk up a (non-existing) 99.99 revision.

http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=493415

Signed-off-by: Moritz Muehlenhoff <jmm@debian.org>
Tested-by: Jan Heitkoetter <devnull@heitkoetter.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
2009-03-17 14:01:29 -07:00
Dan Williams 0cc6bfe901 USB: Option: let cdc-acm handle Sony Ericsson F3507g / Dell 5530
The generic cdc-acm driver is now the best one to handle Sony Ericsson
F3507g-based devices (which the Dell 5530 is a rebrand of), now that all
the pieces are in place (ie, cac477e8f1).
Removing the IDs from option allows cdc-acm to handle the device.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17 14:01:29 -07:00
Alan Stern 391016f6e2 USB: EHCI: expedite unlinks when the root hub is suspended
This patch (as1225) fixes a bug in ehci-hcd.  The condition for
whether unlinked QHs can become IDLE should not be that the controller
is halted, but rather that the controller isn't running.  In other
words when the root hub is suspended, the hardware doesn't own any
QHs.

This fixes a problem that can show up during hibernation: If a QH is
only partially unlinked when the root hub is frozen, then when the
root hub is thawed the QH won't be in the IDLE state.  As a result it
can't be used properly for new URB submissions.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Brandon Philips <brandon@ifup.org>
Tested-by: Brandon Philips <brandon@ifup.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17 14:01:29 -07:00
Karsten Wiese 508db8c954 USB: EHCI: Fix isochronous URB leak
ehci-hcd uses usb_get_urb() and usb_put_urb() in an unbalanced way causing
isochronous URB's kref.counts incrementing once per usb_submit_urb() call.
The culprit is *usb being set to NULL when usb_put_urb() is called after URB
is given back.
Due to other fixes there is no need for ehci-hcd to deal with usb_get_urb()
nor usb_put_urb() anymore, so patch removes their usages in ehci-hcd.
Patch also makes ehci_to_hcd(ehci)->self.bandwidth_allocated adjust, if a
stream finishes.

Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-17 14:01:29 -07:00