The MSM chipidea wrapper has two bits that are used to reset the
first or second phy. Add support for these bits via the reset
controller framework, so that phy drivers can reset their
hardware at the right time during initialization.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
If two devices are probed with this same driver, they'll share
the same platform data structure, while the chipidea core layer
writes and modifies it. This can lead to interesting results
especially if one device is an OTG type chipidea controller and
another is a host. Let's create a copy of this structure per each
device instance so that odd things don't happen.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
When the RESET bit is set in the USBCMD register it resets quite
a few of the wrapper's registers to their reset state. This
includes the GENCONFIG and GENCONFIG2 registers. Currently this
is done by the usb phy and ehci-msm drivers writing into the
controller wrapper's MMIO address space. Let's consolidate the
register writes into the wrapper driver instead so that we
clearly split the wrapper from the phys.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We need to pick the correct phy at runtime based on how the SoC
has been wired onto the board. If the secondary phy is used, take
it out of reset and mux over to it by writing into the TCSR
register. Make sure to do this on reset too, because this
register is reset to the default value (primary phy) after the
RESET bit is set in USBCMD.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The msm chipidea controller uses two main clks, an AHB clk to
read/write the MMIO registers and a core clk called the system
clk that drives the controller itself. Add support for these clks
as they're required in all designs.
Also add support for an optional third clk that we need to turn
on to reset the controller and wrapper logic and other
"housekeeping" things. This clk was removed in later revisions of
the hardware because the reset methodology no longer required
clks to be enabled to propagate resets.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The MSM_USB_BASE macro trick is not very clear, and we're using
it for only one register write so let's just move to using
hw_write_id_reg() and passing the ci pointer instead. That
clearly shows what offset we're using and avoids needing to
include the msm_hsusb_hw.h file when we're going to delete that
file soon.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The core framework already handles setting this parameter with a
platform quirk. Add the appropriate flag so that we always set
AHBBURST to 0. Technically DT should be doing this, but we always
do it for msm chipidea devices so setting the flag in the driver
works just as well. If the burst needs to be anything besides 0,
we expect the 'ahb-burst-config' dts property to be present.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We're not properly marking the glue layer/wrapper device as
runtime active, so runtime PM believes that the hardware state is
inactive when we call pm_runtime_enable() in this driver. This
causes a problem when the glue layer has a power domain
associated with it, because runtime PM will go and disable the
power domain to match the 'inactive' state of the device. Let's
mark the device as active so that runtime PM doesn't improperly
power down this device when it's actually active.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
At some situations, the vbus may already be there before starting
gadget. So we need to check vbus event after switching to gadget in
order to handle missing vbus event. The typical use cases are plugging
vbus cable before driver load or the vbus has already been there
after stopping host but before starting gadget.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Stephen Boyd <stephen.boyd@linaro.org>
Reported-by: Stephen Boyd <stephen.boyd@linaro.org>
The two extcon notifiers are almost the same except for the
variable name for the cable structure and the id notifier inverts
the cable->state logic. Make it the same and replace two
functions with one to save some lines. This also makes it so that
the id cable state is true when the id pin is pulled low, so we
change the name of ->state to ->connected to properly reflect
that we're interested in the cable being connected.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some phys for the chipidea controller are controlled via the ULPI
viewport. Add support for the ULPI bus so that these sorts of
phys can be probed and read/written automatically without having
to duplicate the viewport logic in each phy driver.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We don't call hw_device_reset() with the ci->lock held, so it
doesn't seem like this lock here is protecting anything. Let's
just remove it. This allows us to call sleeping functions like
phy_init() from within the CI_HDRC_CONTROLLER_RESET_EVENT hook.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The chipidea/udc.c file sends a CI_HDRC_CONTROLLER_RESET_EVENT to
the wrapper drivers when it calls hw_device_reset(), but that
function is not called from chipidea/host.c. And the udc.c file
sends the CI_HDRC_CONTROLLER_STOPPED_EVENT but the host.c file
doesn't do anything.
The intent of the reset event is to allow the wrapper driver to
do any wrapper specific things after the reset bit has been set
in the usb command register. Therefore, add this event hook in
the host role after we toggle that bit.
Similarly, the intent of the stopped event is to allow the
wrapper driver to do any wrapper specific things after the device
is stopped. So when we stop the host role, send the stopped
event.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly.
Therefore, add a flag to skip any phy power management in the
core layer, leaving it up to the glue driver to manage.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We're currently emulating the vbus and id interrupts in the OTGSC
read API, but we also need to make sure that if we're handling
the events with extcon that we don't enable the interrupts for
those events in the hardware. Therefore, properly emulate this
register if we're using extcon, but don't enable the interrupts.
This allows me to get my cable connect/disconnect working
properly without getting spurious interrupts on my device that
uses an extcon for these two events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
With the id and vbus detection done via extcon we need to make
sure we poll the status of OTGSC properly by considering what the
extcon is saying, and not just what the register is saying. Let's
move this hw_wait_reg() function to the only place it's used and
simplify it for polling the OTGSC register. Then we can make
certain we only use the hw_read_otgsc() API to read OTGSC, which
will make sure we properly handle extcon events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The qcom HSIC ULPI phy doesn't have any bits set in the vendor or
product ID registers. This makes it impossible to make a ULPI
driver match against the ID registers. Add support to discover
the ULPI phys via DT help alleviate this problem. In the DT case,
we'll look for a ULPI bus node underneath the device registering
the ULPI viewport (or the parent of that device to support
chipidea's device layout) and then match up the phy node
underneath that with the ULPI device that's created.
The side benefit of this is that we can use standard properties
in the phy node like clks, regulators, gpios, etc. because we
don't have firmware like ACPI to turn these things on for us. And
we can use the DT phy binding to point our phy consumer to the
phy provider.
The ULPI bus code supports native enumeration by reading the
vendor ID and product ID registers at device creation time, but
we can't be certain that those register reads will succeed if the
phy is not powered up. To avoid any problems with reading the ID
registers before the phy is powered we fallback to DT matching
when the ID reads fail.
If the ULPI spec had some generic power sequencing for these
registers we could put that into the ULPI bus layer and power up
the device before reading the ID registers. Unfortunately this
doesn't exist and the power sequence is usually device specific.
By having the device matched up with DT we can avoid this
problem.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The ULPI bus can be built as a module, and it will soon be
calling these functions when it supports probing devices from DT.
Export them so they can be used by the ULPI module.
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In the case of ULPI devices, we want to be able to load the
driver before registering the device so that we don't get stuck
in a loop waiting for the phy module to appear and failing usb
controller probe. Currently we request the ulpi module via the
ulpi ids, but in the DT case we might need to request it with the
OF based modalias instead. Add a common function that allows
anyone to request a module with the OF based modalias.
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:
AS arch/powerpc/kernel/misc_32.o
arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]
This problem is evident after commit 989cea5c14 ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created. That was with commit 9994a33865 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").
The offending line does not make a lot of sense. This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.
Thanks to Nicholas Piggin for suggesting this solution.
Fixes: 9994a33865 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The timer type simplifications caused a new gcc warning:
drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));
despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.
The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.
Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
Pull turbostat updates from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: remove obsolete -M, -m, -C, -c options
tools/power turbostat: Make extensible via the --add parameter
tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz
tools/power turbostat: line up headers when -M is used
tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding
tools/power turbostat: Support Knights Mill (KNM)
tools/power turbostat: Display HWP OOB status
tools/power turbostat: fix Denverton BCLK
tools/power turbostat: use intel-family.h model strings
tools/power/turbostat: Add Denverton RAPL support
tools/power/turbostat: Add Denverton support
tools/power/turbostat: split core MSR support into status + limit
tools/power turbostat: fix error case overflow read of slm_freq_table[]
tools/power turbostat: Allocate correct amount of fd and irq entries
tools/power turbostat: switch to tab delimited output
tools/power turbostat: Gracefully handle ACPI S3
tools/power turbostat: tidy up output on Joule counter overflow
Add a new page flag, PageWaiters, to indicate the page waitqueue has
tasks waiting. This can be tested rather than testing waitqueue_active
which requires another cacheline load.
This bit is always set when the page has tasks on page_waitqueue(page),
and is set and cleared under the waitqueue lock. It may be set when
there are no tasks on the waitqueue, which will cause a harmless extra
wakeup check that will clears the bit.
The generic bit-waitqueue infrastructure is no longer used for pages.
Instead, waitqueues are used directly with a custom key type. The
generic code was not flexible enough to have PageWaiters manipulation
under the waitqueue lock (which simplifies concurrency).
This improves the performance of page lock intensive microbenchmarks by
2-3%.
Putting two bits in the same word opens the opportunity to remove the
memory barrier between clearing the lock bit and testing the waiters
bit, after some work on the arch primitives (e.g., ensuring memory
operand widths match and cover both bits).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A page is not added to the swap cache without being swap backed,
so PageSwapBacked mappings can use PG_owner_priv_1 for PageSwapCache.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No point in going through loops and hoops instead of just comparing the
values.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
The mpic is either the main interrupt controller or is cascaded behind a
GIC. The mpic is single instance and the modes are mutually exclusive, so
there is no reason to have seperate cpu hotplug states.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20161221192112.333161745@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Even if both drivers are compiled in only one instance can run on a given
system depending on the available GIC version.
So having seperate hotplug states for them is pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.252416267@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Even if both drivers are compiled in only one instance can run on a given
system depending on the available tracer cell.
So having seperate hotplug states for them is pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: http://lkml.kernel.org/r/20161221192112.162765484@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
hotcpu_notifier(), cpu_notifier(), __hotcpu_notifier(), __cpu_notifier(),
register_hotcpu_notifier(), register_cpu_notifier(),
__register_hotcpu_notifier(), __register_cpu_notifier(),
unregister_hotcpu_notifier(), unregister_cpu_notifier(),
__unregister_hotcpu_notifier(), __unregister_cpu_notifier()
are unused now. Remove them and all related code.
Remove also the now pointless cpu notifier error injection mechanism. The
states can be executed step by step and error rollback is the same as cpu
down, so any state transition can be tested w/o requiring the notifier
error injection.
Some CPU hotplug states are kept as they are (ab)used for hotplug state
tracking.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20161221192112.005642358@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Install the callbacks via the state machine. No functional change.
This is the minimal fixup so we can remove the hotplug notifier mess
completely.
The real rework of this driver to use work queues is still stuck in
review/testing on the SCSI mailing list.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20161221192111.836895753@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Install the callbacks via the state machine. No functional change.
This is the minimal fixup so we can remove the hotplug notifier mess
completely.
The real rework of this driver to use work queues is still stuck in
review/testing on the SCSI mailing list.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20161221192111.757309869@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Developers manage to overwrite states blindly without thought. That's fatal
and hard to debug. Add sanity checks to make it fail.
This requries to restructure the code so that the dynamic state allocation
happens in the same lock protected section as the actual store. Otherwise
the previous assignment of 'Reserved' to the name field would trigger the
overwrite check.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192111.675234535@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The error cleanup which is invoked when the hotplug state setup failed
tries to remove the failed state, which is broken.
Fixes: 8fba38c937 ("x86/msr: Convert to hotplug state machine")
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
In case the driver registration fails, the hotplug callback is leaked.
Not fatal, because it's never invoked as there are no instances registered,
but wrong nevertheless.
Fixes: fdc15a36d8 ("bus/arm-ccn: Convert to hotplug statemachine")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
If the pmu registration fails the registered hotplug callbacks are not
removed. Wrong in any case, but fatal in case of a modular driver.
Replace the nonsensical state names with proper ones while at it.
Fixes: 77c34ef1c3 ("perf/x86/intel/cstate: Convert Intel CSTATE to hotplug state machine")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
The cpu hotplug support of this perf driver is broken in several ways:
1) It adds a instance before setting up the state.
2) The state for the instance is different from the state of the
callback. It's just a randomly chosen state.
3) The instance registration is not error checked so nobody noticed that
the call can never succeed.
4) The state for the multi install callbacks is chosen randomly and
overwrites existing state. This is now prevented by the core code so the
call is guaranteed to fail.
5) The error exit path in the init function leaves the instance registered
and then frees the memory which contains the enqueued hlist node.
6) The remove function is removing the state and not the instance.
Fix it by:
- Setting up the state before adding instances. Use a dynamically allocated
state for it.
- Installing instances after the state has been set up
- Removing the instance in the error path before freeing memory
- Removing the instance not the state in the driver remove callback
While at is use raw_cpu_processor_id(), because cpu_processor_id() cannot
be used in preemptible context, and set the driver data after successful
registration of the pmu.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Frank Li <frank.li@nxp.com>
Cc: Zhengyu Shen <zhengyu.shen@nxp.com>
Link: http://lkml.kernel.org/r/20161221192111.596204211@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The CPU hotplug code is a trainwreck. It leaks a notifier in case of driver
registration error and the per cpu loop is racy against cpu hotplug. Aside
of that the driver should have been written and merged with the new state
machine interfaces in the first place.
Mop up the mess and Convert it to the hotplug state machine.
Signed-off-by: Thomas Grumpy Gleixner <tglx@linutronix.de>
Cc: Nilesh Javali <nilesh.javali@cavium.com>
Cc: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@cavium.com>
Cc: Saurav Kashyap <saurav.kashyap@cavium.com>
Cc: Arun Easi <arun.easi@cavium.com>
Cc: Manish Rangankar <manish.rangankar@cavium.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
The new --add option has replaced the -M, -m, -C, -c options
Eg.
-M 0x10 is now --add msr0x10,raw
-m 0x10 is now --add msr0x10,raw,u32
-C 0x10 is now --add msr0x10,delta
-c 0x10 is now --add msr0x10,delta,u32
The --add option can be repeated to add any number of counters,
while the previous options were limited to adding one of each type.
In addition, the --add option can accept a column label,
and can also display a counter as a percentage of elapsed cycles.
Eg. --add msr0x3fe,core,percent,MY_CC3
Signed-off-by: Len Brown <len.brown@intel.com>
Create the "--add" parameter. This can be used to teach an existing
turbostat binary about any number of any type of counter.
turbostat(8) details the syntax for --add.
Signed-off-by: Len Brown <len.brown@intel.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull cifs fixes from Steve French:
"This ncludes various cifs/smb3 bug fixes, mostly for stable as well.
In the next week I expect that Germano will have some reconnection
fixes, and also I expect to have the remaining pieces of the snapshot
enablement and SMB3 ACLs, but wanted to get this set of bug fixes in"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs_get_root shouldn't use path with tree name
Fix default behaviour for empty domains and add domainauto option
cifs: use %16phN for formatting md5 sum
cifs: Fix smbencrypt() to stop pointing a scatterlist at the stack
CIFS: Fix a possible double locking of mutex during reconnect
CIFS: Fix a possible memory corruption during reconnect
CIFS: Fix a possible memory corruption in push locks
CIFS: Fix missing nls unload in smb2_reconnect()
CIFS: Decrease verbosity of ioctl call
SMB3: parsing for new snapshot timestamp mount parm
Stephen Boyd
Peter Chen
Chanwoo Choi
Linus Torvalds
Larry Finger
Nicholas Piggin
Thomas Gleixner
Anna-Maria Gleixner
Sebastian Andrzej Siewior
Len Brown