This patch fixes a bug on hotmod removing.
After ipmi interface is removed using hotmod, kernel panic occurs when
rmmod impi_si. For example, try this:
# echo "remove,"`cat /proc/ipmi/0/params` > \
/sys/module/ipmi_si/parameters/hotmod
# rmmod ipmi_si
Then, rmmod fails with the following messages.
------------[ cut here ]------------
WARNING: CPU: 12 PID: 10819 at /mnt/repos/linux/lib/list_debug.c:53 __list_del_entry+0x63/0xd0()
CPU: 12 PID: 10819 Comm: rmmod Not tainted 3.17.0-rc1 #19
Hardware name: FUJITSU-SV PRIMERGY BX920 S2/D3030, BIOS 080015 Rev.3D81.3030 02/10/2012
Call Trace:
dump_stack+0x45/0x56
warn_slowpath_common+0x7d/0xa0
warn_slowpath_fmt+0x4c/0x50
__list_del_entry+0x63/0xd0
list_del+0xd/0x30
cleanup_one_si+0x2a/0x230 [ipmi_si]
ipmi_pnp_remove+0x15/0x20 [ipmi_si]
pnp_device_remove+0x24/0x40
__device_release_driver+0x7f/0xf0
driver_detach+0xb0/0xc0
bus_remove_driver+0x55/0xd0
driver_unregister+0x2c/0x50
pnp_unregister_driver+0x12/0x20
cleanup_ipmi_si+0xbc/0xf0 [ipmi_si]
SyS_delete_module+0x132/0x1c0
system_call_fastpath+0x16/0x1b
---[ end trace 70b4377268f85c23 ]---
list_del in cleanup_one_si() fails because the smi_info is already
removed when hotmod removing.
When ipmi interface is removed by hotmod, smi_info is removed by
cleanup_one_si(), but is is still set in drvdata. Therefore when rmmod
ipmi_si, ipmi_pnp_remove tries to remove it again and fails.
By this patch, a pointer to smi_info in drvdata is cleared when hotmod
removing so that it will be not accessed when rmmod.
changelog:
v2:
- Clear drvdata in cleanup_one_si
- Change subject
v1:
https://lkml.org/lkml/2014/9/8/741
Signed-off-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building ipmi on arm with gcc-4.9 results in this warning for an
allmodconfig build:
drivers/char/ipmi/ipmi_si_intf.c: In function 'ipmi_thread':
include/linux/time.h:28:5: warning: 'busy_until.tv_sec' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (lhs->tv_sec > rhs->tv_sec)
^
drivers/char/ipmi/ipmi_si_intf.c:1007:18: note: 'busy_until.tv_sec' was declared here
struct timespec busy_until;
^
The warning is bogus and this case can not occur. Apparently this is a
false positive resulting from gcc getting a little smarter about
tracking assignments but not smart enough.
Marking the ipmi_thread_busy_wait function as inline gives the gcc
optimization logic enough information to figure out for itself that the
case cannot happen, which gets rid of the warning without adding any
fake initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an IPMI controller is used by the firmware and as such marked with
a reserved status, we shouldn't use it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code to send the channel config errors was missing an error report
in one place and needed some more information in another, and had an
extraneous bit of code. Clean all that up.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.
Replace the uses with standard structure definitions instead. This is
similar to pci and usb device registration.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Add a real platform bus device as a parent for
the srom class devices, to prevent non-platform
devices hanging from the bus root.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
as pr_* macros are more preffered over printk, so printk replaced with corresponding pr_* macros
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been functional and stable throughout the year it has spent
in the staging area. It has been patched for minor bugs, coding style issues
and improvements during this period.
This is the second submission of this move-out, after making several style
improvements, as suggested by Dan Carpenter.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the Dell Latitude E6540 which needs a different fan speed multiplier.
Signed-off-by: Steven Honeyman <stevenhoneyman@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a page isn't allocated as __GFP_MOVEABLE it won't move around, so
no need to grab a reference to lock it into place.
Discovered while reviewing page allocation handling in i915 gem.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Before we really unregister the hwrng device, reading will get stuck if
the virtio device is reset. We should return error for reading when we
start to remove the device.
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When we try to hot-remove a busy virtio-rng device from QEMU monitor,
the device can't be hot-removed. Because virtio-rng driver hangs at
wait_for_completion_killable().
This patch exits the waiting by completing have_data completion before
unregistering, resets data_avail to avoid the hwrng core use wrong
buffer bytes.
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A single case of using __get_cpu_var for address calculation.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The khwrngd thread is started when a hwrng device of sufficient
quality is registered. The virtio-rng device is backed by the
hypervisor, and we trust the hypervisor to provide real entropy.
A malicious or badly-implemented hypervisor is a scenario that's
irrelevant -- such a setup is bound to cause all sorts of badness, and a
compromised hwrng is the least of the user's worries.
Given this, we might as well assume that the quality of randomness we
receive is perfectly trustworthy. Hence, we use 100% for the factor,
indicating maximum confidence in the source.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: H. Peter Anvin <hpa@linux.intel.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
call, which is a superset of OpenBSD's getentropy(2) call, for use
with userspace crypto libraries such as LibreSSL. Also add the
ability to have a kernel thread to pull entropy from hardware rng
devices into /dev/random.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wLqJ
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull randomness updates from Ted Ts'o:
"Cleanups and bug fixes to /dev/random, add a new getrandom(2) system
call, which is a superset of OpenBSD's getentropy(2) call, for use
with userspace crypto libraries such as LibreSSL.
Also add the ability to have a kernel thread to pull entropy from
hardware rng devices into /dev/random"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
hwrng: Pass entropy to add_hwgenerator_randomness() in bits, not bytes
random: limit the contribution of the hw rng to at most half
random: introduce getrandom(2) system call
hw_random: fix sparse warning (NULL vs 0 for pointer)
random: use registers from interrupted code for CPU's w/o a cycle counter
hwrng: add per-device entropy derating
hwrng: create filler thread
random: add_hwgenerator_randomness() for feeding entropy from devices
random: use an improved fast_mix() function
random: clean up interrupt entropy accounting for archs w/o cycle counters
random: only update the last_pulled time if we actually transferred entropy
random: remove unneeded hash of a portion of the entropy pool
random: always update the entropy pool under the spinlock
Pull security subsystem updates from James Morris:
"In this release:
- PKCS#7 parser for the key management subsystem from David Howells
- appoint Kees Cook as seccomp maintainer
- bugfixes and general maintenance across the subsystem"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (94 commits)
X.509: Need to export x509_request_asymmetric_key()
netlabel: shorter names for the NetLabel catmap funcs/structs
netlabel: fix the catmap walking functions
netlabel: fix the horribly broken catmap functions
netlabel: fix a problem when setting bits below the previously lowest bit
PKCS#7: X.509 certificate issuer and subject are mandatory fields in the ASN.1
tpm: simplify code by using %*phN specifier
tpm: Provide a generic means to override the chip returned timeouts
tpm: missing tpm_chip_put in tpm_get_random()
tpm: Properly clean sysfs entries in error path
tpm: Add missing tpm_do_selftest to ST33 I2C driver
PKCS#7: Use x509_request_asymmetric_key()
Revert "selinux: fix the default socket labeling in sock_graft()"
X.509: x509_request_asymmetric_keys() doesn't need string length arguments
PKCS#7: fix sparse non static symbol warning
KEYS: revert encrypted key change
ima: add support for measuring and appraising firmware
firmware_class: perform new LSM checks
security: introduce kernel_fw_from_file hook
PKCS#7: Missing inclusion of linux/err.h
...
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
rng_get_data() returns the number of bytes read from the hardware.
The entropy argument to add_hwgenerator_randomness() is passed
directly to credit_entropy_bits() so we should be passing the
number of bits, not bytes here.
Fixes: be4000bc46 "hwrng: create filler thread"
Acked-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
For people who don't trust a hardware RNG which can not be audited,
the changes to add support for RDSEED can be troubling since 97% or
more of the entropy will be contributed from the in-CPU hardware RNG.
We now have a in-kernel khwrngd, so for those people who do want to
implicitly trust the CPU-based system, we could create an arch-rng
hw_random driver, and allow khwrng refill the entropy pool. This
allows system administrator whether or not they trust the CPU (I
assume the NSA will trust RDRAND/RDSEED implicitly :-), and if so,
what level of entropy derating they want to use.
The reason why this is a really good idea is that if different people
use different levels of entropy derating, it will make it much more
difficult to design a backdoor'ed hwrng that can be generally
exploited in terms of the output of /dev/random when different attack
targets are using differing levels of entropy derating.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The getrandom(2) system call was requested by the LibreSSL Portable
developers. It is analoguous to the getentropy(2) system call in
OpenBSD.
The rationale of this system call is to provide resiliance against
file descriptor exhaustion attacks, where the attacker consumes all
available file descriptors, forcing the use of the fallback code where
/dev/[u]random is not available. Since the fallback code is often not
well-tested, it is better to eliminate this potential failure mode
entirely.
The other feature provided by this new system call is the ability to
request randomness from the /dev/urandom entropy pool, but to block
until at least 128 bits of entropy has been accumulated in the
/dev/urandom entropy pool. Historically, the emphasis in the
/dev/urandom development has been to ensure that urandom pool is
initialized as quickly as possible after system boot, and preferably
before the init scripts start execution.
This is because changing /dev/urandom reads to block represents an
interface change that could potentially break userspace which is not
acceptable. In practice, on most x86 desktop and server systems, in
general the entropy pool can be initialized before it is needed (and
in modern kernels, we will printk a warning message if not). However,
on an embedded system, this may not be the case. And so with this new
interface, we can provide the functionality of blocking until the
urandom pool has been initialized. Any userspace program which uses
this new functionality must take care to assure that if it is used
during the boot process, that it will not cause the init scripts or
other portions of the system startup to hang indefinitely.
SYNOPSIS
#include <linux/random.h>
int getrandom(void *buf, size_t buflen, unsigned int flags);
DESCRIPTION
The system call getrandom() fills the buffer pointed to by buf
with up to buflen random bytes which can be used to seed user
space random number generators (i.e., DRBG's) or for other
cryptographic uses. It should not be used for Monte Carlo
simulations or other programs/algorithms which are doing
probabilistic sampling.
If the GRND_RANDOM flags bit is set, then draw from the
/dev/random pool instead of the /dev/urandom pool. The
/dev/random pool is limited based on the entropy that can be
obtained from environmental noise, so if there is insufficient
entropy, the requested number of bytes may not be returned.
If there is no entropy available at all, getrandom(2) will
either block, or return an error with errno set to EAGAIN if
the GRND_NONBLOCK bit is set in flags.
If the GRND_RANDOM bit is not set, then the /dev/urandom pool
will be used. Unlike using read(2) to fetch data from
/dev/urandom, if the urandom pool has not been sufficiently
initialized, getrandom(2) will block (or return -1 with the
errno set to EAGAIN if the GRND_NONBLOCK bit is set in flags).
The getentropy(2) system call in OpenBSD can be emulated using
the following function:
int getentropy(void *buf, size_t buflen)
{
int ret;
if (buflen > 256)
goto failure;
ret = getrandom(buf, buflen, 0);
if (ret < 0)
return ret;
if (ret == buflen)
return 0;
failure:
errno = EIO;
return -1;
}
RETURN VALUE
On success, the number of bytes that was filled in the buf is
returned. This may not be all the bytes requested by the
caller via buflen if insufficient entropy was present in the
/dev/random pool, or if the system call was interrupted by a
signal.
On error, -1 is returned, and errno is set appropriately.
ERRORS
EINVAL An invalid flag was passed to getrandom(2)
EFAULT buf is outside the accessible address space.
EAGAIN The requested entropy was not available, and
getentropy(2) would have blocked if the
GRND_NONBLOCK flag was not set.
EINTR While blocked waiting for entropy, the call was
interrupted by a signal handler; see the description
of how interrupted read(2) calls on "slow" devices
are handled with and without the SA_RESTART flag
in the signal(7) man page.
NOTES
For small requests (buflen <= 256) getrandom(2) will not
return EINTR when reading from the urandom pool once the
entropy pool has been initialized, and it will return all of
the bytes that have been requested. This is the recommended
way to use getrandom(2), and is designed for compatibility
with OpenBSD's getentropy() system call.
However, if you are using GRND_RANDOM, then getrandom(2) may
block until the entropy accounting determines that sufficient
environmental noise has been gathered such that getrandom(2)
will be operating as a NRBG instead of a DRBG for those people
who are working in the NIST SP 800-90 regime. Since it may
block for a long time, these guarantees do *not* apply. The
user may want to interrupt a hanging process using a signal,
so blocking until all of the requested bytes are returned
would be unfriendly.
For this reason, the user of getrandom(2) MUST always check
the return value, in case it returns some error, or if fewer
bytes than requested was returned. In the case of
!GRND_RANDOM and small request, the latter should never
happen, but the careful userspace code (and all crypto code
should be careful) should check for this anyway!
Finally, unless you are doing long-term key generation (and
perhaps not even then), you probably shouldn't be using
GRND_RANDOM. The cryptographic algorithms used for
/dev/urandom are quite conservative, and so should be
sufficient for all purposes. The disadvantage of GRND_RANDOM
is that it can block, and the increased complexity required to
deal with partially fulfilled getrandom(2) requests.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Zach Brown <zab@zabbo.net>
Here's the big tty / serial driver update for 3.17-rc1.
Nothing major, just a number of fixes and new features for different
serial drivers, and some more tty core fixes and documentation of the
tty locks.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2C4ACgkQMUfUDdst+yllVgCgtZl/Mcr/LlxPgjsg2C1AE7nX
YJ4An3o4N112bkdGqhZ7RjAE6K/8YILx
=rPhE
-----END PGP SIGNATURE-----
Merge tag 'tty-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver update from Greg KH:
"Here's the big tty / serial driver update for 3.17-rc1.
Nothing major, just a number of fixes and new features for different
serial drivers, and some more tty core fixes and documentation of the
tty locks.
All of these have been in linux-next for a while"
* tag 'tty-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (82 commits)
tty/n_gsm.c: fix a memory leak in gsmld_open
pch_uart: don't hardcode PCI slot to get DMA device
tty: n_gsm, use setup_timer
Revert "ARC: [arcfpga] stdout-path now suffices for earlycon/console"
serial: sc16is7xx: Correct initialization of s->clk
serial: 8250_dw: Add support for deferred probing
serial: 8250_dw: Add optional reset control support
serial: st-asc: Fix overflow in baudrate calculation
serial: st-asc: Don't call BUG in asc_console_setup()
tty: serial: msm: Make of_device_id array const
tty/n_gsm.c: get gsm->num after gsm_activate_mux
serial/core: Fix too big allocation for attribute member
drivers/tty/serial: use correct type for dma_map/unmap
serial: altera_jtaguart: Fix putchar function passed to uart_console_write()
serial/uart/8250: Add tunable RX interrupt trigger I/F of FIFO buffers
Serial: allow port drivers to have a default attribute group
tty: kgdb_nmi: Automatically manage tty enable
serial: altera_jtaguart: Adpot uart_console_write()
serial: samsung: improve code clarity by defining a variable
serial: samsung: correct the case and default order in switch
...
Here's the big driver misc / char pull request for 3.17-rc1.
Lots of things in here, the thunderbolt support for Apple laptops, some
other new drivers, testing fixes, and other good things. All have been
in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1LcACgkQMUfUDdst+ymaVwCgqMrKFmpduBufOSFROhxlfB5Q
ajsAoNDmIn3pgla+kj23Y5ib20aMi++s
=IdIr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver patches from Greg KH:
"Here's the big driver misc / char pull request for 3.17-rc1.
Lots of things in here, the thunderbolt support for Apple laptops,
some other new drivers, testing fixes, and other good things. All
have been in linux-next for a long time"
* tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (119 commits)
misc: bh1780: Introduce the use of devm_kzalloc
Lattice ECP3 FPGA: Correct endianness
drivers/misc/ti-st: Load firmware from ti-connectivity directory.
dt-bindings: extcon: Add support for SM5502 MUIC device
extcon: sm5502: Change internal hardware switch according to cable type
extcon: sm5502: Detect cable state after completing platform booting
extcon: sm5502: Add support new SM5502 extcon device driver
extcon: arizona: Get MICVDD against extcon device
extcon: Remove unnecessary OOM messages
misc: vexpress: Fix sparse non static symbol warnings
mei: drop unused hw dependent fw status functions
misc: bh1770glc: Use managed functions
pcmcia: remove DEFINE_PCI_DEVICE_TABLE usage
misc: remove DEFINE_PCI_DEVICE_TABLE usage
ipack: Replace DEFINE_PCI_DEVICE_TABLE macro use
drivers/char/dsp56k.c: drop check for negativity of unsigned parameter
mei: fix return value on disconnect timeout
mei: don't schedule suspend in pm idle
mei: start disconnect request timer consistently
mei: reset client connection state on timeout
...
The VFS layer handles those in the very same way, if unset. No need for
additional stubs.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of looping by ourselves we may use %*phN specifier to dump a small
buffer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[ PHuewe: removed now unused variable i ]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Some Atmel TPMs provide completely wrong timeouts from their
TPM_CAP_PROP_TIS_TIMEOUT query. This patch detects that and returns
new correct values via a DID/VID table in the TIS driver.
Tested on ARM using an AT97SC3204T FW version 37.16
Cc: <stable@vger.kernel.org>
[PHuewe: without this fix these 'broken' Atmel TPMs won't function on
older kernels]
Signed-off-by: "Berg, Christopher" <Christopher.Berg@atmel.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Regression in 41ab999c. Call to tpm_chip_put is missing. This
will cause TPM device driver not to unload if tmp_get_random()
is called.
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Properly clean the sysfs entries in the error path
Cc: <stable@vger.kernel.org>
Reported-by: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Most device drivers do call 'tpm_do_selftest' which executes a
TPM_ContinueSelfTest. tpm_i2c_stm_st33 is just pointlessly different,
I think it is bug.
These days we have the general assumption that the TPM is usable by
the kernel immediately after the driver is finished, so we can no
longer defer the mandatory self test to userspace.
Cc: <stable@vger.kernel.org> # 3.12+
Reported-by: Richard Marciel <rmaciel@linux.vnet.ibm.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This reverts commit e052dbf554.
Now that we use the virtio ->scan() function to register with the hwrng
core, we will not get read requests till probe is successfully finished.
So revert the workaround we had in place to refuse read requests while
we were not yet setup completely.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Instead of calling hwrng_register() in the probe routing, call it in the
scan routine. This ensures that when hwrng_register() is successful,
and it requests a few random bytes to seed the kernel's pool at init,
we're ready to service that request.
This will also enable us to remove the workaround added previously to
check whether probe was completed, and only then ask for data from the
host. The revert follows in the next commit.
There's a slight behaviour change here on unsuccessful hwrng_register().
Previously, when hwrng_register() failed, the probe() routine would
fail, and the vqs would be torn down, and driver would be marked not
initialized. Now, the vqs will remain initialized, driver would be
marked initialized as well, but won't be available in the list of RNGs
available to hwrng core. To fix the failures, the procedure remains the
same, i.e. unload and re-load the module, and hope things succeed the
next time around.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Re-arrange the elements of the virtrng_info struct to pack it better.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
vdev is unused in struct virtrng_info, remove it.
CC: Amos Kong <akong@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix checkpatch warning:
WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: virtualization@lists.linux-foundation.org
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
There is no point in having a S390 private implementation and there is
no point in using the raw monotonic time. The NTP freqeuency
adjustment of CLOCK_MONOTONIC is really not doing any harm for the
hang check timer.
Use ktime_get_ns() for everything and get rid of the timespec
conversions.
V2: Drop the raw monotonic and the S390 special case
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJTygXeAAoJENNvdpvBGATwBVYP/3OHIb58JhHjC/GbHKhe0UdX
eSBle+8bcDdwADXBQ2Slzp7bVBwBHaEgKOz0Y9iTObrICb5orUGtB7MmGi9b9WIW
8igTkvNhQxwNZat89U5SOpPuwSJEyR9LeIKN8JG75j+ymX/H1vjsojJcXxfZzYT0
qoiUs32VbmglfVPy1WvPLZ/0fYtaRwzE6des7yzZHYbEvgX5JIJ7m4sQftMj4a+L
CNiLHXLijsUX9CG94Gjw7R7/PLK83UNM+ER5zUTIC6EqRJCZVIQAU0zvyE5sm3ZK
v3n8aJypZZhNBGJm4SNWlwsbwllx9BvPOq2DadY+/Jpzqrxy1saYB+XoKKdT3t2Y
3OJb/eh02wuCzCzJgNNP9CJhdPV7h4qrg5M1OqrBsFgXEAlISLvWEM+//FB8Hsmv
NDKeWl6Y5Iy6UCZDVQpuYCJTo46ACt0DBLpOE9tXDtz6yuLF+Hs3GmRPz368EcEy
t98UmU7mS447FQdqjThKdH1g/ZeGepXDMkk/hosmnck7OgQzuLMBnAagwouQ9YSH
O32MyvGHkAPEL2SB2WzGdWIHr/K2EWiyAoO3OVaUrJ7tVrGvVig/WsgYyNaHzBlp
5VRCdBXJ78tH+KYl0lIkrzrOnd1AegQtIIH5E3iZsdUVqCM/DdDd5ewwWxC7Ar3s
PGrT4lp8vqIT0H3D65a5
=8rgT
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fix from Ted Ts'o:
"Fix a BUG splat found by trinity"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: check for increase of entropy_count because of signed conversion
Pull crypto fixes from Herbert Xu:
"This push fixes a boot hang in virt guests when the virtio RNG is
enabled"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: virtio - ensure reads happen after successful probe
hwrng: fetch randomness only after device init
The expression entropy_count -= ibytes << (ENTROPY_SHIFT + 3) could
actually increase entropy_count if during assignment of the unsigned
expression on the RHS (mind the -=) we reduce the value modulo
2^width(int) and assign it to entropy_count. Trinity found this.
[ Commit modified by tytso to add an additional safety check for a
negative entropy_count -- which should never happen, and to also add
an additional paranoia check to prevent overly large count values to
be passed into urandom_read(). ]
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
[linux-3.16-rc5/drivers/char/dsp56k.c:386]: (style) Checking if unsigned
variable 'arg' is less than zero.
Source code is
if (arg > 31 || arg < 0)
return -EINVAL;
But
static long dsp56k_ioctl(struct file *file, unsigned int cmd,
unsigned long arg)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80411
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For CPU's that don't have a cycle counter, or something equivalent
which can be used for random_get_entropy(), random_get_entropy() will
always return 0. In that case, substitute with the saved interrupt
registers to add a bit more unpredictability.
Some folks have suggested hashing all of the registers
unconditionally, but this would increase the overhead of
add_interrupt_randomness() by at least an order of magnitude, and this
would very likely be unacceptable.
The changes in this commit have been benchmarked as mostly unaffecting
the overhead of add_interrupt_randomness() if the entropy counter is
present, and doubling the overhead if it is not present.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Jörn Engel <joern@logfs.org>
This patch introduces a derating factor to struct hwrng for
the random bits going into the kernel input pool, and a common
default derating for drivers which do not specify one.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
This can be viewed as the in-kernel equivalent of hwrngd;
like FUSE it is a good thing to have a mechanism in user land,
but for some reasons (simplicity, secrecy, integrity, speed)
it may be better to have it in kernel space.
This patch creates a thread once a hwrng registers, and uses
the previously established add_hwgenerator_randomness() to feed
its data to the input pool as long as needed. A derating factor
is used to bias the entropy estimation and to disable this
mechanism entirely when set to zero.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
This patch adds an interface to the random pool for feeding entropy
in-kernel.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Use more efficient fast_mix() function. Thanks to George Spelvin for
doing the leg work to find a more efficient mixing function.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
For architectures that don't have cycle counters, the algorithm for
deciding when to avoid giving entropy credit due to back-to-back timer
interrupts didn't make any sense, since we were checking every 64
interrupts. Change it so that we only give an entropy credit if the
majority of the interrupts are not based on the timer.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
In xfer_secondary_pull(), check to make sure we need to pull from the
secondary pool before checking and potentially updating the
last_pulled time.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
We previously extracted a portion of the entropy pool in
mix_pool_bytes() and hashed it in to avoid racing CPU's from returning
duplicate random values. Now that we are using a spinlock to prevent
this from happening, this is no longer necessary. So remove it, to
simplify the code a bit.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
Instead of using lockless techniques introduced in commit
902c098a36, use spin_trylock to try to grab entropy pool's lock. If
we can't get the lock, then just try again on the next interrupt.
Based on discussions with George Spelvin.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
The hwrng core asks for random data in the hwrng_register() call itself
from commit d9e7972619. This doesn't play well with virtio -- the
DRIVER_OK bit is only set by virtio core on a successful probe, and
we're not yet out of our probe routine when this call is made. This
causes the host to not acknowledge any requests we put in the virtqueue,
and the insmod or kernel boot process just waits for data to arrive from
the host, which never happens.
CC: Kees Cook <keescook@chromium.org>
CC: Jason Cooper <jason@lakedaemon.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: <stable@vger.kernel.org> # For v3.15+
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit d9e7972619 "hwrng: add randomness to system from rng sources"
added a call to rng_get_data() from the hwrng_register() function.
However, some rng devices need initialization before data can be read
from them.
This commit makes the call to rng_get_data() depend on no init fn
pointer being registered by the device. If an init function is
registered, this call is made after device init.
CC: Kees Cook <keescook@chromium.org>
CC: Jason Cooper <jason@lakedaemon.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: <stable@vger.kernel.org> # For v3.15+
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This resolves a number of merge issues with changes in this tree and
Linus's tree at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_close_start() already validates the port counts and issues
a diagnostic if validation fails.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since at least before 2.6.30, it has not been possible to observe
a hung up file pointer in a tty driver's open() method unless/until
the driver open() releases the tty_lock() (eg., before blocking).
This is because tty_open() adds the file pointer while holding
the tty_lock() _and_ doesn't release the lock until after calling
the tty driver's open() method. [ Before tty_lock(), this was
lock_kernel(). ]
Since __tty_hangup() first waits on the tty_lock() before
enumerating and hanging up the open file pointers, either
__tty_hangup() will wait for the tty_lock() or tty_open() will
not yet have added the file pointer. For example,
CPU 0 | CPU 1
|
tty_open | __tty_hangup
.. | ..
tty_lock | ..
tty_reopen | tty_lock / blocks
.. |
tty_add_file(tty, filp) |
.. |
tty->ops->open(tty, filp) |
tty_port_open |
tty_port_block_til_ready |
.. |
while (1) |
.. |
tty_unlock | / unblocks
schedule | for each filp on tty->tty_files
| f_ops = tty_hung_up_fops;
| ..
| tty_unlock
tty_lock |
.. |
tty_unlock |
Note that since tty_port_block_til_ready() and similar drop
the tty_lock while blocking, when woken, the file pointer
must then be tested for having been hung up.
Also, fix bit-rotted drivers that used extra_count to track the
port->count bump.
CC: Mikael Starvik <starvik@axis.com>
CC: Samuel Ortiz <samuel@sortiz.org>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -ENOMEM instead of success if ioremap() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes sure a format string cannot accidentally leak into a device name.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f36fdb9f02 (i8k: Force SMM to run on CPU 0) adds support
for multi-core CPUs to the driver. Unfortunately, that causes it
to fail loading if compiled without SMP support, at least on
32 bit kernels. Kernel log shows "i8k: unable to get SMM Dell
signature", and function i8k_smm is found to return -EINVAL.
Testing revealed that the culprit is the missing return value check
of set_cpus_allowed_ptr.
Fixes: f36fdb9f02 (i8k: Force SMM to run on CPU 0)
Reported-by: Jim Bos <jim876@xs4all.nl>
Tested-by: Jim Bos <jim876@xs4all.nl>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both systems need non-standard parameters for fan multiplier
and maximum fan speed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Dell systems provide more granular fan speed selection.
Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Labels are known to be wrong for several Dell laptops.
For example, a single fan may be shown as right fan when in reality
it sits on the left side of the chassis. Drop all labels to avoid
such inaccuracies. Users can select labels in the sensors configuration
file instead if desired.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0fb7a01af5 "random: simplify accounting code", introduced in
v3.15, has a very nasty accounting problem when the entropy pool has
has fewer bytes of entropy than the number of requested reserved
bytes. In that case, "have_bytes - reserved" goes negative, and since
size_t is unsigned, the expression:
ibytes = min_t(size_t, ibytes, have_bytes - reserved);
... does not do the right thing. This is rather bad, because it
defeats the catastrophic reseeding feature in the
xfer_secondary_pool() path.
It also can cause the "BUG: spinlock trylock failure on UP" for some
kernel configurations when prandom_reseed() calls get_random_bytes()
in the early init, since when the entropy count gets corrupted,
credit_entropy_bits() erroneously believes that the nonblocking pool
has been fully initialized (when in fact it is not), and so it calls
prandom_reseed(true) recursively leading to the spinlock BUG.
The logic is *not* the same it was originally, but in the cases where
it matters, the behavior is the same, and the resulting code is
hopefully easier to read and understand.
Fixes: 0fb7a01af5 "random: simplify accounting code"
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Greg Price <price@mit.edu>
Cc: stable@vger.kernel.org #v3.15
Pull vfs updates from Al Viro:
"This the bunch that sat in -next + lock_parent() fix. This is the
minimal set; there's more pending stuff.
In particular, I really hope to get acct.c fixes merged this cycle -
we need that to deal sanely with delayed-mntput stuff. In the next
pile, hopefully - that series is fairly short and localized
(kernel/acct.c, fs/super.c and fs/namespace.c). In this pile: more
iov_iter work. Most of prereqs for ->splice_write with sane locking
order are there and Kent's dio rewrite would also fit nicely on top of
this pile"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (70 commits)
lock_parent: don't step on stale ->d_parent of all-but-freed one
kill generic_file_splice_write()
ceph: switch to iter_file_splice_write()
shmem: switch to iter_file_splice_write()
nfs: switch to iter_splice_write_file()
fs/splice.c: remove unneeded exports
ocfs2: switch to iter_file_splice_write()
->splice_write() via ->write_iter()
bio_vec-backed iov_iter
optimize copy_page_{to,from}_iter()
bury generic_file_aio_{read,write}
lustre: get rid of messing with iovecs
ceph: switch to ->write_iter()
ceph_sync_direct_write: stop poking into iov_iter guts
ceph_sync_read: stop poking into iov_iter guts
new helper: copy_page_from_iter()
fuse: switch to ->write_iter()
btrfs: switch to ->write_iter()
ocfs2: switch to ->write_iter()
xfs: switch to ->write_iter()
...
path, which I refuse to CC stable since (1) I discovered it myself, and
(2) it's been there forever with no reports.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YCNa
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Main excitement is a virtio_scsi fix for alloc holding spinlock on the
abort path, which I refuse to CC stable since (1) I discovered it
myself, and (2) it's been there forever with no reports"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_scsi: don't call virtqueue_add_sgs(... GFP_NOIO) holding spinlock.
virtio-rng: fixes for device registration/unregistration
virtio-rng: fix boot with virtio-rng device
virtio-rng: support multiple virtio-rng devices
virtio_ccw: introduce device_lost in virtio_ccw_device
virtio: virtio_break_device() to mark all virtqueues broken.
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- ACPICA update to upstream version 20140424. That includes a
number of fixes and improvements related to things like GPE
handling, table loading, headers, memory mapping and unmapping,
DSDT/SSDT overriding, and the Unload() operator. The acpidump
utility from upstream ACPICA is included too. From Bob Moore,
Lv Zheng, David Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices
rather than PNP devices for ACPI device objects with _HID by
default. PNP devices will still be created for the ACPI device
object with device IDs corresponding to real PNP devices, so
that change should not break things left and right, and we're
expecting to see more and more ACPI-enumerated platform devices
in the future. From Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing
it to handle system suspend/resume on Asus T100 correctly.
From Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions
if certain additional conditions related to coordination within
device hierarchy are met. Related PM documentation update and
ACPI PM domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling,
Tony Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from
Chander Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie,
Doug Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from
Jacob Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way
from Thomas Renninger.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tpdF
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm into next
Pull ACPI and power management updates from Rafael Wysocki:
"ACPICA is the leader this time (63 commits), followed by cpufreq (28
commits), devfreq (15 commits), system suspend/hibernation (12
commits), ACPI video and ACPI device enumeration (10 commits each).
We have no major new features this time, but there are a few
significant changes of how things work. The most visible one will
probably be that we are now going to create platform devices rather
than PNP devices by default for ACPI device objects with _HID. That
was long overdue and will be really necessary to be able to use the
same drivers for the same hardware blocks on ACPI and DT-based systems
going forward. We're not expecting fallout from this one (as usual),
but it's something to watch nevertheless.
The second change having a chance to be visible is that ACPI video
will now default to using native backlight rather than the ACPI
backlight interface which should generally help systems with broken
Win8 BIOSes. We're hoping that all problems with the native backlight
handling that we had previously have been addressed and we are in a
good enough shape to flip the default, but this change should be easy
enough to revert if need be.
In addition to that, the system suspend core has a new mechanism to
allow runtime-suspended devices to stay suspended throughout system
suspend/resume transitions if some extra conditions are met
(generally, they are related to coordination within device hierarchy).
However, enabling this feature requires cooperation from the bus type
layer and for now it has only been implemented for the ACPI PM domain
(used by ACPI-enumerated platform devices mostly today).
Also, the acpidump utility that was previously shipped as a separate
tool will now be provided by the upstream ACPICA along with the rest
of ACPICA code, which will allow it to be more up to date and better
supported, and we have one new cpuidle driver (ARM clps711x).
The rest is improvements related to certain specific use cases,
cleanups and fixes all over the place.
Specifics:
- ACPICA update to upstream version 20140424. That includes a number
of fixes and improvements related to things like GPE handling,
table loading, headers, memory mapping and unmapping, DSDT/SSDT
overriding, and the Unload() operator. The acpidump utility from
upstream ACPICA is included too. From Bob Moore, Lv Zheng, David
Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices rather
than PNP devices for ACPI device objects with _HID by default. PNP
devices will still be created for the ACPI device object with
device IDs corresponding to real PNP devices, so that change should
not break things left and right, and we're expecting to see more
and more ACPI-enumerated platform devices in the future. From
Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing it
to handle system suspend/resume on Asus T100 correctly. From
Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions if
certain additional conditions related to coordination within device
hierarchy are met. Related PM documentation update and ACPI PM
domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling, Tony
Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from Chander
Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie, Doug
Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from Jacob
Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way from
Thomas Renninger"
* tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (187 commits)
ACPICA: Namespace: Remove _PRP method support.
intel_pstate: Improve initial busy calculation
intel_pstate: add sample time scaling
intel_pstate: Correct rounding in busy calculation
intel_pstate: Remove C0 tracking
PM / hibernate: fixed typo in comment
ACPI: Fix x86 regression related to early mapping size limitation
ACPICA: Tables: Add mechanism to control early table checksum verification.
ACPI / scan: use platform bus type by default for _HID enumeration
ACPI / scan: always register ACPI LPSS scan handler
ACPI / scan: always register memory hotplug scan handler
ACPI / scan: always register container scan handler
ACPI / scan: Change the meaning of missing .attach() in scan handlers
ACPI / scan: introduce platform_id device PNP type flag
ACPI / scan: drop unsupported serial IDs from PNP ACPI scan handler ID list
ACPI / scan: drop IDs that do not comply with the ACPI PNP ID rule
ACPI / PNP: use device ID list for PNPACPI device enumeration
ACPI / scan: .match() callback for ACPI scan handlers
ACPI / battery: wakeup the system only when necessary
power_supply: allow power supply devices registered w/o wakeup source
...
* acpica: (63 commits)
ACPICA: Namespace: Remove _PRP method support.
ACPI: Fix x86 regression related to early mapping size limitation
ACPICA: Tables: Add mechanism to control early table checksum verification.
ACPICA: acpidump: Fix repetitive table dump in -n mode.
ACPI: Clean up acpi_os_map/unmap_memory() to eliminate __iomem.
ACPICA: Clean up redudant definitions already defined elsewhere
ACPICA: Linux headers: Add <asm/acenv.h> to remove mis-ordered inclusion of <asm/acpi.h>
ACPICA: Linux headers: Add <acpi/platform/aclinuxex.h>
ACPICA: Linux headers: Remove ACPI_PREEMPTION_POINT() due to no usages.
ACPICA: Update version to 20140424.
ACPICA: Comment/format update, no functional change.
ACPICA: Events: Update GPE handling and initialization code.
ACPICA: Remove extraneous error message for large number of GPEs.
ACPICA: Tables: Remove old mechanism to validate if XSDT contains NULL entries.
ACPICA: Tables: Add new mechanism to skip NULL entries in RSDT and XSDT.
ACPICA: acpidump: Add support to force using RSDT.
ACPICA: Back port of improvements on exception code.
ACPICA: Back port of _PRP update.
ACPICA: acpidump: Fix truncated RSDP signature validation.
ACPICA: Linux header: Add support for stubbed externals.
...
Pull scheduler updates from Ingo Molnar:
"The main scheduling related changes in this cycle were:
- various sched/numa updates, for better performance
- tree wide cleanup of open coded nice levels
- nohz fix related to rq->nr_running use
- cpuidle changes and continued consolidation to improve the
kernel/sched/idle.c high level idle scheduling logic. As part of
this effort I pulled cpuidle driver changes from Rafael as well.
- standardized idle polling amongst architectures
- continued work on preparing better power/energy aware scheduling
- sched/rt updates
- misc fixlets and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (49 commits)
sched/numa: Decay ->wakee_flips instead of zeroing
sched/numa: Update migrate_improves/degrades_locality()
sched/numa: Allow task switch if load imbalance improves
sched/rt: Fix 'struct sched_dl_entity' and dl_task_time() comments, to match the current upstream code
sched: Consolidate open coded implementations of nice level frobbing into nice_to_rlimit() and rlimit_to_nice()
sched: Initialize rq->age_stamp on processor start
sched, nohz: Change rq->nr_running to always use wrappers
sched: Fix the rq->next_balance logic in rebalance_domains() and idle_balance()
sched: Use clamp() and clamp_val() to make sys_nice() more readable
sched: Do not zero sg->cpumask and sg->sgp->power in build_sched_groups()
sched/numa: Fix initialization of sched_domain_topology for NUMA
sched: Call select_idle_sibling() when not affine_sd
sched: Simplify return logic in sched_read_attr()
sched: Simplify return logic in sched_copy_attr()
sched: Fix exec_start/task_hot on migrated tasks
arm64: Remove TIF_POLLING_NRFLAG
metag: Remove TIF_POLLING_NRFLAG
sched/idle: Make cpuidle_idle_call() void
sched/idle: Reflow cpuidle_idle_call()
sched/idle: Delay clearing the polling bit
...
Here is the big char / misc driver updates for 3.16-rc1.
Lots of different driver updates for a variety of different drivers and
minor driver subsystems.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONWI8ACgkQMUfUDdst+ykvQACdGxTChdEU7edElDAXeelVmu8v
D1UAoLDvqwUsN7t5v+WG2wkOvhf5MEA7
=tVMP
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into next
Pull char/misc driver patches from Greg KH:
"Here is the big char / misc driver update for 3.16-rc1.
Lots of different driver updates for a variety of different drivers
and minor driver subsystems.
All have been in linux-next with no reported issues"
* tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (79 commits)
hv: use correct order when freeing monitor_pages
spmi: of: fixup generic SPMI devicetree binding example
applicom: dereferencing NULL on error path
misc: genwqe: fix uninitialized return value in genwqe_free_sync_sgl()
miscdevice.h: Simple syntax fix to make pointers consistent.
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
mcb: Add support for shared PCI IRQs
drivers: Remove duplicate conditionally included subdirs
misc: atmel_pwm: only build for supported platforms
mei: me: move probe quirk to cfg structure
mei: add per device configuration
mei: me: read H_CSR after asserting reset
mei: me: drop harmful wait optimization
mei: me: fix hw ready reset flow
mei: fix memory leak of mei_clients array
uio: fix vma io range check in mmap
drivers: uio_dmem_genirq: Fix memory leak in uio_dmem_genirq_probe()
w1: do not unlock unheld list_mutex in __w1_remove_master_device()
w1: optional bundling of netlink kernel replies
connector: allow multiple messages to be sent in one packet
...
Pull block core updates from Jens Axboe:
"It's a big(ish) round this time, lots of development effort has gone
into blk-mq in the last 3 months. Generally we're heading to where
3.16 will be a feature complete and performant blk-mq. scsi-mq is
progressing nicely and will hopefully be in 3.17. A nvme port is in
progress, and the Micron pci-e flash driver, mtip32xx, is converted
and will be sent in with the driver pull request for 3.16.
This pull request contains:
- Lots of prep and support patches for scsi-mq have been integrated.
All from Christoph.
- API and code cleanups for blk-mq from Christoph.
- Lots of good corner case and error handling cleanup fixes for
blk-mq from Ming Lei.
- A flew of blk-mq updates from me:
* Provide strict mappings so that the driver can rely on the CPU
to queue mapping. This enables optimizations in the driver.
* Provided a bitmap tagging instead of percpu_ida, which never
really worked well for blk-mq. percpu_ida relies on the fact
that we have a lot more tags available than we really need, it
fails miserably for cases where we exhaust (or are close to
exhausting) the tag space.
* Provide sane support for shared tag maps, as utilized by scsi-mq
* Various fixes for IO timeouts.
* API cleanups, and lots of perf tweaks and optimizations.
- Remove 'buffer' from struct request. This is ancient code, from
when requests were always virtually mapped. Kill it, to reclaim
some space in struct request. From me.
- Remove 'magic' from blk_plug. Since we store these on the stack
and since we've never caught any actual bugs with this, lets just
get rid of it. From me.
- Only call part_in_flight() once for IO completion, as includes two
atomic reads. Hopefully we'll get a better implementation soon, as
the part IO stats are now one of the more expensive parts of doing
IO on blk-mq. From me.
- File migration of block code from {mm,fs}/ to block/. This
includes bio.c, bio-integrity.c, bounce.c, and ioprio.c. From me,
from a discussion on lkml.
That should describe the meat of the pull request. Also has various
little fixes and cleanups from Dave Jones, Shaohua Li, Duan Jiong,
Fengguang Wu, Fabian Frederick, Randy Dunlap, Robert Elliott, and Sam
Bradshaw"
* 'for-3.16/core' of git://git.kernel.dk/linux-block: (100 commits)
blk-mq: push IPI or local end_io decision to __blk_mq_complete_request()
blk-mq: remember to start timeout handler for direct queue
block: ensure that the timer is always added
blk-mq: blk_mq_unregister_hctx() can be static
blk-mq: make the sysfs mq/ layout reflect current mappings
blk-mq: blk_mq_tag_to_rq should handle flush request
block: remove dead code in scsi_ioctl:blk_verify_command
blk-mq: request initialization optimizations
block: add queue flag for disabling SG merging
block: remove 'magic' from struct blk_plug
blk-mq: remove alloc_hctx and free_hctx methods
blk-mq: add file comments and update copyright notices
blk-mq: remove blk_mq_alloc_request_pinned
blk-mq: do not use blk_mq_alloc_request_pinned in blk_mq_map_request
blk-mq: remove blk_mq_wait_for_tags
blk-mq: initialize request in __blk_mq_alloc_request
blk-mq: merge blk_mq_alloc_reserved_request into blk_mq_alloc_request
blk-mq: add helper to insert requests from irq context
blk-mq: remove stale comment for blk_mq_complete_request()
blk-mq: allow non-softirq completions
...
This is a static checker fix. The "dev" variable is always NULL after
the while statement so we would be dereferencing a NULL pointer here.
Fixes: 819a3eba42 ('[PATCH] applicom: fix error handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPICA doesn't include protections around address space checking, Linux
build tests always complain increased sparse warnings around ACPICA
internal acpi_os_map/unmap_memory() invocations. This patch tries to fix
this issue permanently.
There are 2 choices left for us to solve this issue:
1. Add __iomem address space awareness into ACPICA.
2. Remove sparse checker of __iomem from ACPICA source code.
This patch chooses solution 2, because:
1. Most of the acpi_os_map/unmap_memory() invocations are used for ACPICA.
table mappings, which in fact are not IO addresses.
2. The only IO addresses usage is for "system memory space" mapping code in:
drivers/acpi/acpica/exregion.c
drivers/acpi/acpica/evrgnini.c
drivers/acpi/acpica/exregion.c
The mapped address is accessed in the handler of "system memory space"
- acpi_ex_system_memory_space_handler(). This function in fact can be
changed to invoke acpi_os_read/write_memory() so that __iomem can
always be type-casted in the OSL layer.
According to the above investigation, we drew the following conclusion:
It is not a good idea to introduce __iomem address space awareness into
ACPICA mostly in order to protect non-IO addresses.
We can simply remove __iomem for acpi_os_map/unmap_memory() to remove
__iomem checker for ACPICA code. Then we need to enforce external usages
to invoke other APIs that are aware of __iomem address space.
The external usages are:
drivers/acpi/apei/einj.c
drivers/acpi/acpi_extlog.c
drivers/char/tpm/tpm_acpi.c
drivers/acpi/nvs.c
This patch thus performs cleanups in this way:
1. Add acpi_os_map/unmap_iomem() to be invoked by non-ACPICA code.
2. Remove __iomem from acpi_os_map/unmap_memory().
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
last merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ZFSi
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fix from Ted Ts'o:
"This fixes a BUG_ON-causing regression that was introduced during the
last merge window"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: fix BUG_ON caused by accounting simplification
There are several fixes in this patch (mostly because it's hard
splitting them up):
- Revert the name field in struct hwrng back to 'const'. Also, don't
do an extra kmalloc for the name - just wasteful.
- Deal with allocation failures properly.
- Use IDA to allocate device number instead of brute forcing one.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Commit "virtio-rng: support multiple virtio-rng devices" has broken
boot with a virtio-rng device because the 'init' callback of the
virtio-rng device was left unitialized to garbage, and got called
by the hwrng infrastructure, killing the guest on boot.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fixes: 08e53fbdb8
Commit ee1de406ba ("random: simplify accounting logic") simplified
things too much, in that it allows the following to trigger an
overflow that results in a BUG_ON crash:
dd if=/dev/urandom of=/dev/zero bs=67108707 count=1
Thanks to Peter Zihlstra for discovering the crash, and Hannes
Frederic for analyizing the root cause.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Greg Price <price@mit.edu>
Current hwrng core supports to register multiple hwrng devices,
and there is only one device really works in the same time.
QEMU alsu supports to have multiple virtio-rng backends.
This patch changes virtio-rng driver to support multiple
virtio-rng devices.
]# cat /sys/class/misc/hw_random/rng_available
virtio_rng.0 virtio_rng.1
]# cat /sys/class/misc/hw_random/rng_current
virtio_rng.0
]# echo -n virtio_rng.1 > /sys/class/misc/hw_random/rng_current
]# dd if=/dev/hwrng of=/dev/null
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. The NULL assignment to np->units is removed as there is no
interaction between this field and sun4v_hvapi_unregister. Also, the
labels out_free_units and out_free are removed as they are no longer
required.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Chromebooks (at least Acer C720 and Pixel) implement an ACPI object
for TPM, but don't implement the _DSM method to support PPI. As
a result, the TPM driver fails to load on those machines after
commit 1569a4c4ce (ACPI / TPM: detect PPI features by checking
availability of _DSM functions) which causes them to fail to
resume from system suspend, becuase they require the TPM hardware
to be put into the right state during resume and the TPM driver
is necessary for that.
Fix the problem by making tpm_add_ppi() return 0 when tpm_ppi_handle
is still NULL after walking the ACPI namespace in search for the PPI
_DSM, which allows the TPM driver to load and operate the hardware
(during system resume in particular), but avoid creating the PPI
sysfs group in that case.
This change is based on a prototype patch from Jiang Liu.
Fixes: 1569a4c4ce (ACPI / TPM: detect PPI features by checking availability of _DSM functions)
References: https://bugzilla.kernel.org/show_bug.cgi?id=74021
Reported-by: James Duley <jagduley@gmail.com>
Reported-by: Phillip Dixon <phil@dixon.gen.nz>
Tested-by: Brandon Casey <drafnel@gmail.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On 64 bit systems the agp_info struct has a 4 byte hole between
->agp_mode and ->aper_base. We need to clear it to avoid disclosing
stack information to userspace.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will be needed for pending changes to the scsi midlayer that now
calls lower level block APIs, as well as any blk-mq driver that wants to
contribute to the random pool.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jens Axboe <axboe@fb.com>
Here are a number of small tty/serial driver fixes for 3.15-rc2. Also
in here are some Documentation file removals for drivers that we removed
a long time ago, no need to keep it around any longer.
All of these have been in linux-next for a bit.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNRmhMACgkQMUfUDdst+yl1egCgi9FsrVUE57dZ2AJNuVwxeh90
cDQAoIAbaKSE1ooen/txjFI27rB92qgZ
=d+yo
-----END PGP SIGNATURE-----
Merge tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty/serial driver fixes for 3.15-rc2. Also
in here are some Documentation file removals for drivers that we
removed a long time ago, no need to keep it around any longer.
All of these have been in linux-next for a bit"
* tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250, disable "too much work" messages"
serial: amba-pl011: fix regression, causing an Oops on rmmod
tty: Fix help text of SYNCLINK_CS
tty: fix memleak in alloc_pid
ttyprintk: Allow built as a module
ttyprintk: Fix wrong tty_unregister_driver() call in the error path
serial: 8250, disable "too much work" messages
Documentation/serial: Delete obsolete driver documentation
serial: omap: Fix missing pm_runtime_resume handling by simplifying code
serial_core: Fix pm imbalance on unbind
serial: pl011: change Rx burst size to half of trigger level
serial: timberdale: Depend on X86_32
serial: st-asc: Fix SysRq char handling
Revert "serial: clps711x: Give a chance to perform useful tasks during wait loop"
serial_core: Fix conditional start_tx on ring buffer not empty
serial: efm32: use $vendor,$device scheme for compatible string
serial: omap: free the wakeup settings in remove
Merge ipmi fixes from Corey Minyard:
"Things collected since last kernel release.
Some of these are pretty important. The first three are bug fixes.
The next two are to hopefully make everyone happy about allowing
ACPI to be on all the time and not have IPMI have an effect on the
system when not in use. The last is a little cleanup"
* emailed patches from Corey Minyard <cminyard@mvista.com>:
ipmi: boolify some things
ipmi: Turn off all activity on an idle ipmi interface
ipmi: Turn off default probing of interfaces
ipmi: Reset the KCS timeout when starting error recovery
ipmi: Fix a race restarting the timer
Char: ipmi_bt_sm, fix infinite loop
The IPMI driver would wake up periodically looking for events and
watchdog pretimeouts. If there is nothing waiting for these events,
it's really kind of pointless to be checking for them. So modify the
driver so the message handler can pass down if it needs the lower layer
to be waiting for these. Modify the system interface lower layer to
turn off all timer and thread activity if the upper layer doesn't need
anything and it is not currently handling messages. And modify the
message handler to not restart the timer if its timer is not needed.
The timers and kthread will still be enabled if:
- the SI interface is handling a message.
- a user has enabled watching for events.
- the IPMI watchdog timer is in use (since it uses pretimeouts).
- the message handler is waiting on a remote response.
- a user has registered to receive commands.
This mostly affects interfaces without interrupts. Interfaces with
interrupts already don't use CPU in the system interface when the
interface is idle.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default probing can cause problems with some system, slow booting,
extra CPU usages, etc. Turn it off by default and give a config option
to enable it.
From: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The OBF timer in KCS was not reset in one situation when error recovery
was started, resulting in an immediate timeout.
Reported-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With recent changes it is possible for the timer handler to detect an
idle interface and not start the timer, but the thread to start an
operation at the same time. The thread will not start the timer in that
instance, resulting in the timer not running.
Instead, move all timer operations under the lock and start the timer in
the thread if it detect non-idle and the timer is not already running.
Moving under locks allows the last timeout to be set in both the thread
and the timer. 'Timer is not running' means that the timer is not
pending and smi_timeout() is not running. So we need a flag to detect
this correctly.
Also fix a few other timeout bugs: setting the last timeout when the
interrupt has to be disabled and the timer started, and setting the last
timeout in check_start_timer_thread possibly racing with the timer
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In read_all_bytes, we do
unsigned char i;
...
bt->read_data[0] = BMC2HOST;
bt->read_count = bt->read_data[0];
...
for (i = 1; i <= bt->read_count; i++)
bt->read_data[i] = BMC2HOST;
If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the
'for' loop. Make 'i' an 'int' instead of 'char' to get rid of the
overflow and finish the loop after 255 iterations every time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-debugged-by: Rui Hui Dian <rhdian@novell.com>
Cc: Tomas Cech <tcech@suse.cz>
Cc: Corey Minyard <minyard@acm.org>
Cc: <openipmi-developer@lists.sourceforge.net>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enabling SYNCLINK_CS as a module builds synclink_cs, not synclinkmp.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is well written to be used as a module, just the exit call
is missing.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyprintk driver calls tty_unregister_driver() wrongly in the error
path of tty_register_driver(). Also, setting ttyprintk_driver to NULL
is utterly superfluous, so let's get rid of it, too.
Reported-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver for the "Picochip picoXcell true random number generator" was
added in v2.6.39. Its Kconfig symbol has always depended on
PICOXCELL_PC3X3. But that Kconfig symbol has never been part of the
tree. This means this driver has never been buildable. Let's remove it.
It can be re-added if its dependencies are actually part of the tree.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HW_RANDOM_ATMEL should not only default to ARCH_AT91, it should depend
on it. This driver is useless on other architectures.
Likewise, HW_RANDOM_EXYNOS should depend on ARCH_EXYNOS, as it it
useless on other architectures.
Also set the default to HW_RANDOM for the few architecture-specific
drivers which didn't have it yet, for consistency.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This makes configuration more convenient IMHO, and avoids having to
repeat the dependency on HW_RANDOM for every single driver.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
UML_RANDOM is the only hardware random number generator option which
does not depend on HW_RANDOM. Having it in the middle of the other
options breaks the alignment in "make menuconfig". Move it at the last
position to avoid that.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull bmc2835 crypto fix from Herbert Xu:
"This fixes a potential boot crash on bcm2835 due to the recent change
that now causes hardware RNGs to be accessed on registration"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: bcm2835 - fix oops when rng h/w is accessed during registration
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.
Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.
This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
...
Commit "d9e7972 hwrng: add randomness to system from rng sources"
exposed a bug in the bcm2835-rng driver resulting in boot failure
on Raspberry Pi due to the following oops:
[ 28.261523] BUG: soft lockup - CPU#0 stuck for 23s! [swapper:1]
[ 28.271058]
[ 28.275958] CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.0+ #11
[ 28.285374] task: db480000 ti: db484000 task.ti: db484000
[ 28.294279] PC is at bcm2835_rng_read+0x28/0x48
[ 28.302276] LR is at hwrng_register+0x1a8/0x238
.
.
.
The RNG h/w is not completely initialized and enabled before
hwrng_register() is called and so the bcm2835_rng_read() fails.
Fix this by making the warmup/enable writes before registering
the RNG source with the hwrng core.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull x86 platform driver updates from Matthew Garrett:
"Support for the new keyboard features on the Thinkpad Carbon, a bunch
of updates for the Sony and Toshiba drivers, a new driver for upcoming
Alienware hardware and a few misc fixes. There's a couple of patches
that got Acked today but aren't invasive, so I'll send a further PR
for them next week"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (28 commits)
alienware-wmi: cover some scenarios where memory allocations would fail
Add WMI driver for controlling AlienFX features on some Alienware products
fujitsu-tablet: add support for Lifebook T901 and T902
x86, platform: Make HP_WIRELESS option text more descriptive
x86, acpi: LLVMLinux: Remove nested functions from Thinkpad ACPI
save and restore adaptive keyboard mode for suspend and,resume
support Thinkpad X1 Carbon 2nd generation's adaptive keyboard
toshiba_acpi: Fix whitespace
toshiba_acpi: Update version and copyright info
toshiba_acpi: Add accelerometer support
toshiba_acpi: Add ECO mode led support
toshiba_acpi: Add touchpad enable/disable support-
toshiba_acpi: Add keyboard backlight support
toshiba_acpi: Adapt Illumination code to use SCI
toshiba_acpi: Add System Configuration Interface
thinkpad_acpi: Fix inconsistent mute LED after resume
sonypi: Simplify dependencies
Revert "X86 platform: New BayTrail IOSF-SB MBI driver"
sony-laptop: remove useless sony-laptop versioning
sony-laptop: add smart connect control function
...
If the renamed symbol is defined lib/iomap.c implements ioport_map and
ioport_unmap and currently (nearly) all platforms define the port
accessor functions outb/inb and friend unconditionally. So
HAS_IOPORT_MAP is the better name for this.
Consequently NO_IOPORT is renamed to NO_IOPORT_MAP.
The motivation for this change is to reintroduce a symbol HAS_IOPORT
that signals if outb/int et al are available. I will address that at
least one merge window later though to keep surprises to a minimum and
catch new introductions of (HAS|NO)_IOPORT.
The changes in this commit were done using:
$ git grep -l -E '(NO|HAS)_IOPORT' | xargs perl -p -i -e 's/\b((?:CONFIG_)?(?:NO|HAS)_IOPORT)\b/$1_MAP/'
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
will be showing up in Intel Broadwell CPU's.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=RtMT
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random changes from Ted Ts'o:
"A number of cleanups plus support for the RDSEED instruction, which
will be showing up in Intel Broadwell CPU's"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: Add arch_has_random[_seed]()
random: If we have arch_get_random_seed*(), try it before blocking
random: Use arch_get_random_seed*() at init time and once a second
x86, random: Enable the RDSEED instruction
random: use the architectural HWRNG for the SHA's IV in extract_buf()
random: clarify bits/bytes in wakeup thresholds
random: entropy_bytes is actually bits
random: simplify accounting code
random: tighten bound on random_read_wakeup_thresh
random: forget lock in lockless accounting
random: simplify accounting logic
random: fix comment on "account"
random: simplify loop in random_read
random: fix description of get_random_bytes
random: fix comment on proc_do_uuid
random: fix typos / spelling errors in comments
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 3.15:
- Added 3DES driver for OMAP4/AM43xx
- Added AVX2 acceleration for SHA
- Added hash-only AEAD algorithms in caam
- Removed tegra driver as it is not functioning and the hardware is
too slow
- Allow blkcipher walks over AEAD (needed for ARM)
- Fixed unprotected FPU/SSE access in ghash-clmulni-intel
- Fixed highmem crash in omap-sham
- Add (zero entropy) randomness when initialising hardware RNGs
- Fixed unaligned ahash comletion functions
- Added soft module depedency for crc32c for initrds that use crc32c"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (60 commits)
crypto: ghash-clmulni-intel - use C implementation for setkey()
crypto: x86/sha1 - reduce size of the AVX2 asm implementation
crypto: x86/sha1 - fix stack alignment of AVX2 variant
crypto: x86/sha1 - re-enable the AVX variant
crypto: sha - SHA1 transform x86_64 AVX2
crypto: crypto_wq - Fix late crypto work queue initialization
crypto: caam - add missing key_dma unmap
crypto: caam - add support for aead null encryption
crypto: testmgr - add aead null encryption test vectors
crypto: export NULL algorithms defines
crypto: caam - remove error propagation handling
crypto: hash - Simplify the ahash_finup implementation
crypto: hash - Pull out the functions to save/restore request
crypto: hash - Fix the pointer voodoo in unaligned ahash
crypto: caam - Fix first parameter to caam_init_rng
crypto: omap-sham - Map SG pages if they are HIGHMEM before accessing
crypto: caam - Dynamic memory allocation for caam_rng_ctx object
crypto: allow blkcipher walks over AEAD data
crypto: remove direct blkcipher_walk dependency on transform
hwrng: add randomness to system from rng sources
...
doubling of the default queue length though.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=AoMS
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing exciting: virtio-blk users might see a bit of a boost from the
doubling of the default queue length though"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-blk: base queue-depth on virtqueue ringsize or module param
Revert a02bbb1ccfe8: MAINTAINERS: add virtio-dev ML for virtio
virtio: fail adding buffer on broken queues.
virtio-rng: don't crash if virtqueue is broken.
virtio_balloon: don't crash if virtqueue is broken.
virtio_blk: don't crash, report error if virtqueue is broken.
virtio_net: don't crash if virtqueue is broken.
virtio_balloon: don't softlockup on huge balloon changes.
virtio: Use pci_enable_msix_exact() instead of pci_enable_msix()
MAINTAINERS: virtio-dev is subscribers only
tools/virtio: add a missing )
tools/virtio: fix missing kmemleak_ignore symbol
tools/virtio: update internal copies of headers
Add predicate functions for having arch_get_random[_seed]*(). The
only current use is to avoid the loop in arch_random_refill() when
arch_get_random_seed_long() is unavailable.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
If we have arch_get_random_seed*(), try to use it for emergency refill
of the entropy pool before giving up and blocking on /dev/random. It
may or may not work in the moment, but if it does work, it will give
the user better service than blocking will.
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Use arch_get_random_seed*() in two places in the Linux random
driver (drivers/char/random.c):
1. During entropy pool initialization, use RDSEED in favor of RDRAND,
with a fallback to the latter. Entropy exhaustion is unlikely to
happen there on physical hardware as the machine is single-threaded
at that point, but could happen in a virtual machine. In that
case, the fallback to RDRAND will still provide more than adequate
entropy pool initialization.
2. Once a second, issue RDSEED and, if successful, feed it to the
entropy pool. To ensure an extra layer of security, only credit
half the entropy just in case.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
To help assuage the fears of those who think the NSA can introduce a
massive hack into the instruction decode and out of order execution
engine in the CPU without hundreds of Intel engineers knowing about
it (only one of which woud need to have the conscience and courage of
Edward Snowden to spill the beans to the public), use the HWRNG to
initialize the SHA starting value, instead of xor'ing it in
afterwards.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
These are a recurring cause of confusion, so rename them to
hopefully be clearer.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The variable 'entropy_bytes' is set from an expression that actually
counts bits. Fortunately it's also only compared to values that also
count bits. Rename it accordingly.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
With this we handle "reserved" in just one place. As a bonus the
code becomes less nested, and the "wakeup_write" flag variable
becomes unnecessary. The variable "flags" was already unused.
This code behaves identically to the previous version except in
two pathological cases that don't occur. If the argument "nbytes"
is already less than "min", then we didn't previously enforce
"min". If r->limit is false while "reserved" is nonzero, then we
previously applied "reserved" in checking whether we had enough
bits, even though we don't apply it to actually limit how many we
take. The callers of account() never exercise either of these cases.
Before the previous commit, it was possible for "nbytes" to be less
than "min" if userspace chose a pathological configuration, but no
longer.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We use this value in a few places other than its literal meaning,
in particular in _xfer_secondary_pool() as a minimum number of
bits to pull from the input pool at a time into either output
pool. It doesn't make sense to pull more bits than the whole size
of an output pool.
We could and possibly should separate the quantities "how much
should the input pool have to have to wake up /dev/random readers"
and "how much should we transfer from the input to an output pool
at a time", but nobody is likely to be sad they can't set the first
quantity to more than 1024 bits, so for now just limit them both.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The only mutable data accessed here is ->entropy_count, but since
10b3a32d2 ("random: fix accounting race condition") we use cmpxchg to
protect our accesses to ->entropy_count here. Drop the use of the
lock.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This logic is exactly equivalent to the old logic, but it should
be easier to see what it's doing.
The equivalence depends on one fact from outside this function:
when 'r->limit' is false, 'reserved' is zero. (Well, two facts;
the other is that 'reserved' is never negative.)
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This comment didn't quite keep up as extract_entropy() was split into
four functions. Put each bit by the function it describes.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The loop condition never changes until just before a break, so we
might as well write it as a constant. Also since a996996dd7
("random: drop weird m_time/a_time manipulation") we don't do anything
after the loop finishes, so the 'break's might as well return
directly. Some other simplifications.
There should be no change in behavior introduced by this commit.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
After this remark was written, commit d2e7c96af added a use of
arch_get_random_long() inside the get_random_bytes codepath.
The main point stands, but it needs to be reworded.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There's only one function here now, as uuid_strategy is long gone.
Also make the bit about "If accesses via ..." clearer.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
A bad implementation of virtio might cause us to mark the virtqueue
broken: we'll dev_err() in that case, and the device is useless, but
let's not BUG().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When bringing a new RNG source online, it seems like it would make sense
to use some of its bytes to make the system entropy pool more random,
as done with all sorts of other devices that contain per-device or
per-boot differences.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge "qcom driver changes for v3.15" from Kumar Gala:
We've split Qualcomm MSM support into legacy and multiplatform. These
drivers are only relevant on the multiplatform supported SoCs so switch the
Kconfig depends to ARCH_QCOM.
* tag 'qcom-drivers-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
gpio: msm: switch Kconfig to ARCH_QCOM depends
hwrng: msm: switch Kconfig to ARCH_QCOM depends
power: reset: msm - switch Kconfig to ARCH_QCOM depends
drm/msm: drop ARCH_MSM Kconfig depend
tty: serial: msm: Enable building msm_serial for ARCH_QCOM
We've split Qualcomm MSM support into legacy and multiplatform. The RNG
driver is only relevant on the multiplatform supported SoCs so switch the
Kconfig depends to ARCH_QCOM.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
CC: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The loff_t type may be wider than phys_addr_t (e.g. on 32-bit systems).
Consequently, the file offset may be truncated in the assignment.
Currently, /dev/mem wraps around, which may cause applications to read
or write incorrect regions of memory by accident.
Let's follow POSIX file semantics here and return 0 when reading from
and -EFBIG when writing to an offset that cannot be represented by a
phys_addr_t.
Note that the conditional is optimized out by the compiler if loff_t
has the same size as phys_addr_t.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small char/misc driver fixes, along with some
documentation updates, for 3.14-rc3. Nothing major, just a number of
fixes for reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+hvIACgkQMUfUDdst+ykGRQCgpi/LgypVecwQlv73TsHLNZo/
ybIAniXJlLgf4xu3q0J+8br3iQ7sg8pC
=m+up
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some small char/misc driver fixes, along with some
documentation updates, for 3.14-rc3. Nothing major, just a number of
fixes for reported issues"
* tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "misc: eeprom: sunxi: Add new compatibles"
Revert "ARM: sunxi: dt: Convert to the new SID compatibles"
misc: mic: fix possible signed underflow (undefined behavior) in userspace API
ARM: sunxi: dt: Convert to the new SID compatibles
misc: eeprom: sunxi: Add new compatibles
misc: genwqe: Fix potential memory leak when pinning memory
Documentation:Update Documentation/zh_CN/arm64/memory.txt
Documentation:Update Documentation/zh_CN/arm64/booting.txt
Documentation:Chinese translation of Documentation/arm64/tagged-pointers.txt
raw: set range for MAX_RAW_DEVS
raw: test against runtime value of max_raw_minors
Drivers: hv: vmbus: Don't timeout during the initial connection with host
Drivers: hv: vmbus: Specify the target CPU that should receive notification
VME: Correct read/write alignment algorithm
mei: don't unset read cb ptr on reset
mei: clear write cb from waiting list on reset
While we are at it, don't do kmap() under kmap_atomic(), *especially*
for a page we'd allocated with GFP_KERNEL. It's spelled "page_address",
and had that been more than that, we'd have a real trouble - kmap_high()
can block, and doing that while holding kmap_atomic() is a Bad Idea(tm).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
My static checker complains that:
drivers/char/hw_random/core.c:341 hwrng_register()
warn: we tested 'old_rng' before and it was 'false'
The problem is that sometimes we test "if (!old_rng)" and sometimes we
test "if (must_register_misc)". The static checker knows they are
equivalent but a human being reading the code could easily be confused.
I have simplified the code by removing the "must_register_misc" variable
and I have removed the redundant check on "if (!old_rng)".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: David Airlie <airlied@linux.ie>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Ashley Lai <ashley@ashleylai.com>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig symbol MAX_RAW_DEVS is meant to be between 1 and 65536. But
those boundaries are not enforced by its Kconfig entry.
Note that MAX_RAW_DEVS is used to set MAX_RAW_MINORS in
drivers/char/raw.c. If one would accidentally set MAX_RAW_DEVS to an
invalid value, that invalid value will actually end up being used in
raw_init().
So add an appropriate range to this Kconfig entry.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bind_get() checks the device number it is called with. It uses
MAX_RAW_MINORS for the upper bound. But MAX_RAW_MINORS is set at compile
time while the actual number of raw devices can be set at runtime. This
means the test can either be too strict or too lenient. And if the test
ends up being too lenient bind_get() might try to access memory beyond
what was allocated for "raw_devices".
So check against the runtime value (max_raw_minors) in this function.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jan Kara <jack@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix
drivers/char/ipmi/ipmi_si_intf.c: In function 'ipmi_parisc_probe':
drivers/char/ipmi/ipmi_si_intf.c:2752:2: error: 'rv' undeclared (first use in this function)
drivers/char/ipmi/ipmi_si_intf.c:2752:2: note: each undeclared identifier is reported only once for each function it appears in
Introduced by commit d02b3709ff ("ipmi: Cleanup error return")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm updates from Dave Airlie:
"Been a bit busy, first week of kids school, and waiting on other trees
to go in before I could send this, so its a bit later than I'd
normally like.
Highlights:
- core:
timestamp fixes, lots of misc cleanups
- new drivers:
bochs virtual vga
- vmwgfx:
major overhaul for their nextgen virt gpu.
- i915:
runtime D3 on HSW, watermark fixes, power well work, fbc fixes,
bdw is no longer prelim.
- nouveau:
gk110/208 acceleration, more pm groundwork, old overlay support
- radeon:
dpm rework and clockgating for CIK, pci config reset, big endian
fixes
- tegra:
panel support and DSI support, build as module, prime.
- armada, omap, gma500, rcar, exynos, mgag200, cirrus, ast:
fixes
- msm:
hdmi support for mdp5"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (595 commits)
drm/nouveau: resume display if any later suspend bits fail
drm/nouveau: fix lock unbalance in nouveau_crtc_page_flip
drm/nouveau: implement hooks for needed for drm vblank timestamping support
drm/nouveau/disp: add a method to fetch info needed by drm vblank timestamping
drm/nv50: fill in crtc mode struct members from crtc_mode_fixup
drm/radeon/dce8: workaround for atom BlankCrtc table
drm/radeon/DCE4+: clear bios scratch dpms bit (v2)
drm/radeon: set si_notify_smc_display_change properly
drm/radeon: fix DAC interrupt handling on DCE5+
drm/radeon: clean up active vram sizing
drm/radeon: skip async dma init on r6xx
drm/radeon/runpm: don't runtime suspend non-PX cards
drm/radeon: add ring to fence trace functions
drm/radeon: add missing trace point
drm/radeon: fix VMID use tracking
drm: ast,cirrus,mgag200: use drm_can_sleep
drm/gma500: Lock struct_mutex around cursor updates
drm/i915: Fix the offset issue for the stolen GEM objects
DRM: armada: fix missing DRM_KMS_FB_HELPER select
drm/i915: Decouple GPU error reporting from ring initialisation
...
Pull hwmon updates from Jean Delvare:
"This include it87 driver improvements, and a tree-wide change of my
e-mail address"
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Update Jean Delvare's e-mail address
hwmon: (it87) Print proper names for the IT8771E and IT8772E
hwmon: (it87) Add support for the ITE IT8603E
Merge ipmi fixes from Corey Minyard:
"Just some collected fixes for 3.14. Nothing huge"
* emailed patches from Corey Minyard <minyard@acm.org>:
ipmi: Cleanup error return
ipmi: fix timeout calculation when bmc is disconnected
ipmi: use USEC_PER_SEC instead of 1000000 for more meaningful
ipmi: remove deprecated IRQF_DISABLED
Return proper errors for a lot of IPMI failure cases. Also call
pci_disable_device when IPMI PCI devices are removed.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Loading ipmi_si module while bmc is disconnected, we found the timeout
is longer than 5 secs. Actually it takes about 3 mins and 20
secs.(HZ=250)
error message as below:
Dec 12 19:08:59 linux kernel: IPMI BT: timeout in RD_WAIT [ ] 1 retries left
Dec 12 19:08:59 linux kernel: BT: write 4 bytes seq=0x01 03 18 00 01
[...]
Dec 12 19:12:19 linux kernel: IPMI BT: timeout in RD_WAIT [ ]
Dec 12 19:12:19 linux kernel: failed 2 retries, sending error response
Dec 12 19:12:19 linux kernel: IPMI: BT reset (takes 5 secs)
Dec 12 19:12:19 linux kernel: IPMI BT: flag reset [ ]
Function wait_for_msg_done() use schedule_timeout_uninterruptible(1) to
sleep 1 tick, so we should subtract jiffies_to_usecs(1) instead of 100
usecs from timeout.
Reported-by: Hu Shiyuan <hushiyuan@huawei.com>
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use USEC_PER_SEC instead of 1000000, that making the later bugfix
more clearly.
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
- FIFO event channels. Key advantages: support for over 100,000 events (2^17),
16 different event priorities, improved fairness in event latency through
the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with paravirtualized
disk and network, paravirtualized interrupts and timers, no emulated devices
of any kind (and thus no qemu), no BIOS or legacy boot — but instead of
requiring PV MMU, it uses the HVM hardware extensions to virtualize the
pagetables, as well as system calls and other privileged operations."
(from "The Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS4BmLAAoJEFjIrFwIi8fJ4SAH/iNGESowgMhfW64vRA8pBWq+
NRJpUjYjjwmbxpwoNl6NPwn15cIXFyc3sMtvvrDD3taRDyko2RFuT+NTjpO05xPh
d/cRpRXpXERHoiFgPf/WTp7ONBDhvPtHG0+BzJKwgqEIOUYXdbhD+gEjaVlFJScS
CAY68OLmk7XYMSZBNzPfKNbSCyhVgZF7wpaimK9lxZBKsFRCDIq6jIyrAsC8epIL
6V/V4l2S6lk/uUeGB6ULphYeINjI2kkpbSfCd1vyenLfWpVscc2o8uWEYFcZMAxy
V4HpsoseuqrfdDqgPfud3VgogdISvbkCvDfW85rzfDP4MWxei2mVHFtJ/gSBV+g=
=ToNG
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from Konrad Rzeszutek Wilk:
"Two major features that Xen community is excited about:
The first is event channel scalability by David Vrabel - we switch
over from an two-level per-cpu bitmap of events (IRQs) - to an FIFO
queue with priorities. This lets us be able to handle more events,
have lower latency, and better scalability. Good stuff.
The other is PVH by Mukesh Rathor. In short, PV is a mode where the
kernel lets the hypervisor program page-tables, segments, etc. With
EPT/NPT capabilities in current processors, the overhead of doing this
in an HVM (Hardware Virtual Machine) container is much lower than the
hypervisor doing it for us.
In short we let a PV guest run without doing page-table, segment,
syscall, etc updates through the hypervisor - instead it is all done
within the guest container. It is a "hybrid" PV - hence the 'PVH'
name - a PV guest within an HVM container.
The major benefits are less code to deal with - for example we only
use one function from the the pv_mmu_ops (which has 39 function
calls); faster performance for syscall (no context switches into the
hypervisor); less traps on various operations; etc.
It is still being baked - the ABI is not yet set in stone. But it is
pretty awesome and we are excited about it.
Lastly, there are some changes to ARM code - you should get a simple
conflict which has been resolved in #linux-next.
In short, this pull has awesome features.
Features:
- FIFO event channels. Key advantages: support for over 100,000
events (2^17), 16 different event priorities, improved fairness in
event latency through the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with
paravirtualized disk and network, paravirtualized interrupts and
timers, no emulated devices of any kind (and thus no qemu), no BIOS
or legacy boot — but instead of requiring PV MMU, it uses the HVM
hardware extensions to virtualize the pagetables, as well as system
calls and other privileged operations." (from "The
Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels"
* tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (52 commits)
xen/pvh: Set X86_CR0_WP and others in CR0 (v2)
MAINTAINERS: add git repository for Xen
xen/pvh: Use 'depend' instead of 'select'.
xen: delete new instances of __cpuinit usage
xen/fb: allow xenfb initialization for hvm guests
xen/evtchn_fifo: fix error return code in evtchn_fifo_setup()
xen-platform: fix error return code in platform_pci_init()
xen/pvh: remove duplicated include from enlighten.c
xen/pvh: Fix compile issues with xen_pvh_domain()
xen: Use dev_is_pci() to check whether it is pci device
xen/grant-table: Force to use v1 of grants.
xen/pvh: Support ParaVirtualized Hardware extensions (v3).
xen/pvh: Piggyback on PVHVM XenBus.
xen/pvh: Piggyback on PVHVM for grant driver (v4)
xen/grant: Implement an grant frame array struct (v3).
xen/grant-table: Refactor gnttab_init
xen/grants: Remove gnttab_max_grant_frames dependency on gnttab_init.
xen/pvh: Piggyback on PVHVM for event channels (v2)
xen/pvh: Update E820 to work with PVH (v2)
xen/pvh: Secondary VCPU bringup (non-bootup CPUs)
...
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
Pull security layer updates from James Morris:
"Changes for this kernel include maintenance updates for Smack, SELinux
(and several networking fixes), IMA and TPM"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (39 commits)
SELinux: Fix memory leak upon loading policy
tpm/tpm-sysfs: active_show() can be static
tpm: tpm_tis: Fix compile problems with CONFIG_PM_SLEEP/CONFIG_PNP
tpm: Make tpm-dev allocate a per-file structure
tpm: Use the ops structure instead of a copy in tpm_vendor_specific
tpm: Create a tpm_class_ops structure and use it in the drivers
tpm: Pull all driver sysfs code into tpm-sysfs.c
tpm: Move sysfs functions from tpm-interface to tpm-sysfs
tpm: Pull everything related to /dev/tpmX into tpm-dev.c
char: tpm: nuvoton: remove unused variable
tpm: MAINTAINERS: Cleanup TPM Maintainers file
tpm/tpm_i2c_atmel: fix coccinelle warnings
tpm/tpm_ibmvtpm: fix unreachable code warning (smatch warning)
tpm/tpm_i2c_stm_st33: Check return code of get_burstcount
tpm/tpm_ppi: Check return value of acpi_get_name
tpm/tpm_ppi: Do not compare strcmp(a,b) == -1
ima: remove unneeded size_limit argument from ima_eventdigest_init_common()
ima: update IMA-templates.txt documentation
ima: pass HASH_ALGO__LAST as hash algo in ima_eventdigest_init()
ima: change the default hash algorithm to SHA1 in ima_eventdigest_ng_init()
...
Here's the big tty/serial driver pull request for 3.14-rc1
There are a number of n_tty fixes and cleanups, and some serial driver
bugfixes, and we got rid of one obsolete driver, making this series
remove more lines than added, always a nice surprise.
All of these have been in linux-next with no reports of issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdiiAACgkQMUfUDdst+ymInACgu+gjm0q6sua8Zsk9HN3Ko0jK
Zy0AoI7jieqSxZfvZD84US98HTiWtumH
=z6GV
-----END PGP SIGNATURE-----
Merge tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver pull request for 3.14-rc1
There are a number of n_tty fixes and cleanups, and some serial driver
bugfixes, and we got rid of one obsolete driver, making this series
remove more lines than added, always a nice surprise.
All of these have been in linux-next with no reports of issues"
* tag 'tty-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (60 commits)
tty/serial: at91: disable uart timer at start of shutdown
serial: 8250: enable UART_BUG_NOMSR for Tegra
tty/serial: at91: reset rx_ring when port is shutdown
tty/serial: at91: fix race condition in atmel_serial_remove
tty/serial: at91: Handle shutdown more safely
serial: sirf: correct condition for fetching dma buffer into tty
serial: sirf: provide pm entries of uart_ops
serial: sirf: use PM macro initialize PM functions
serial: clps711x: Enable driver compilation with COMPILE_TEST
serial: clps711x: Add support for N_IRDA line discipline
tty: synclink: avoid sleep_on race
tty/amiserial: avoid interruptible_sleep_on
tty: delete non-required instances of include <linux/init.h>
tty: an overflow of multiplication in drivers/tty/cyclades.c
serial: Remove old SC26XX driver
serial: add support for 200 v3 series Titan card
serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chip
tty: Removing the deprecated function tty_vhangup_locked()
TTY/n_gsm: Removing the wrong tty_unlock/lock() in gsm_dlci_release()
tty/serial: at91: document clock properties
...
Here's the big char/misc driver patches for 3.14-rc1.
Lots of little things, and a new "big" driver, genwqe. Full details are
in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdgc8ACgkQMUfUDdst+ynt9ACguAhrO2WlowdcUZELadTEpqLX
gbkAn0+c1rjizVdIRvs83aQRNJP6w1uR
=oPmD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver patches for 3.14-rc1.
Lots of little things, and a new "big" driver, genwqe. Full details
are in the shortlog"
* tag 'char-misc-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
mei: limit the number of consecutive resets
mei: revamp mei reset state machine
drivers/char: don't use module_init in non-modular ttyprintk.c
VMCI: fix error handling path when registering guest driver
extcon: gpio: Add power resume support
Documentation: HOWTO: Updates on subsystem trees, patchwork, -next (vs. -mm) in ko_KR
Documentation: HOWTO: update for 2.6.x -> 3.x versioning in ko_KR
Documentation: HOWTO: update stable address in ko_KR
Documentation: HOWTO: update LXR web link in ko_KR
char: nwbutton: open-code interruptible_sleep_on
mei: fix syntax in comments and debug output
mei: nfc: mei_nfc_free has to be called under lock
mei: use hbm idle state to prevent spurious resets
mei: do not run reset flow from the interrupt thread
misc: genwqe: fix return value check in genwqe_device_create()
GenWQE: Fix warnings for sparc
GenWQE: Fix compile problems for Alpha
Documentation/misc-devices/mei/mei-amt-version.c: remove unneeded call of mei_deinit()
GenWQE: Rework return code for flash-update ioctl
sgi-xp: open-code interruptible_sleep_on_timeout
...
Conflicts are getting out of hand, and now we have to shuffle even
more in -next which was also shuffled in -fixes (the call for
drm_mode_config_reset needs to move yet again).
So do a proper backmerge. I wanted to wait with this for the 3.13
relaese, but alas let's just do this now.
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_pm.c
Besides the conflict around the forcewake get/put (where we chaged the
called function in -fixes and added a new parameter in -next) code all
the current conflicts are of the adjacent lines changed type.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The TTY_PRINTK option is bool, and hence this code is either
present or absent. It will never be modular, so using
module_init as an alias for __initcall is rather misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
Pull APM update for 3.14-rc1 from Jiri Kosina.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/apm:
apm-emulation: add hibernation APM events to support suspend2disk
The nwbutton driver uses interruptible_sleep_on to wait for buttons
getting pressed after we enter the read() function, which is inherently
racy and cannot be fixed by using wait_event without changing the
driver's user space interface.
Instead, this patch just uses an open-coded variant of the same
interruptible_sleep_on() call, so the driver behavior doesn't change
but we remove the sleep_on family from the kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The four variants of the synclink driver use the same code in their
open() callback to wait for a port in process of being closed,
using interruptible_sleep_on, which is racy and going away soon.
Making things worse, these functions hold the BTM while doing so,
which means that if we ever enter this code path, we cannot actually
continue since the other thread that is in process of closing the
port can no longer get the BTM.
This addresses both issues by using wait_event_interruptible_tty()
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're accessing the PCI_COMMAND register here, so use the appropriate
#define. The bit we're writing (1 << 14) isn't defined by the PCI or PCIe
spec, so we don't have a name for it.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In i810_setup(), i830_setup(), and i9xx_setup(), we use the result of
pci_bus_address() as an argument to ioremap() and to compute gtt_phys_addr.
These should use pci_resource_start() instead because we want the CPU
physical address, not the bus address.
If there were an AGP device behind a host bridge that translated addresses,
e.g., a PNP0A08 device with _TRA != 0, this would fix a bug. I'm not aware
of any of those, but they are possible.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Per the Intel 915G/915GV/... Chipset spec (document number 301467-005),
GTTADR is a standard PCI BAR.
The PCI core reads GTTADR at enumeration-time. Use pci_bus_address()
instead of reading it again in the driver. This works correctly for both
32-bit and 64-bit BARs. The spec above only mentions 32-bit GTTADR, but we
should still use the standard interface.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Per the Intel 915G/915GV/... Chipset spec (document number 301467-005),
MMADR is a standard PCI BAR.
The PCI core reads MMADR at enumeration-time. Use pci_bus_address()
instead of reading it again in the driver. This works correctly for both
32-bit and 64-bit BARs. The spec above only mentions 32-bit MMADR, but we
should still use the standard interface.
Also, stop clearing the low 19 bits of the bus address because it's invalid
to use addresses outside the region defined by the BAR. The spec claims
MMADR is 512KB; if that's the case, those bits will be zero anyway.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Per the Intel 915G/915GV/... Chipset spec (document number 301467-005),
GMADR is a standard PCI BAR.
The PCI core reads GMADR at enumeration-time. Use pci_bus_address()
instead of reading it again in the driver. This works correctly for both
32-bit and 64-bit BARs. The spec above only mentions 32-bit GMADR, but
Yinghai's patch (link below) indicates some devices have a 64-bit GMADR.
[bhelgaas: reworked starting from http://lkml.kernel.org/r/1385851238-21085-13-git-send-email-yinghai@kernel.org]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only use of gtt_bus_addr is as an argument to ioremap(), so it is a CPU
physical address, not a bus address. Rename it to gtt_phys_addr to reflect
this.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
amd_irongate_configure(), ati_configure(), and nvidia_configure() call
ioremap() on an address read directly from a BAR. But a BAR contains a
bus address, and ioremap() expects a CPU physical address. Use
pci_resource_start() to obtain the physical address.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some embedded systems use hibernation for fast boot. and in it,
some software components need to handle specific things before
hibernation and after restore. So it needs to capture the apm
status about these pm events.
Currently apm just supports suspend to ram, but not suspend to disk,
so here add logic about hibernation apm events.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Per the AGP 3.0 spec, APBASE is a standard PCI BAR and may be either 32
bits or 64 bits wide. Many drivers read APBASE directly, but they only
handled 32-bit BARs.
The PCI core reads APBASE at enumeration-time. Use pci_bus_address()
instead of reading it again in the driver. This works correctly for both
32-bit and 64-bit BARs.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
so we make it static
CC: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
CC: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
If CONFIG_PM_SLEEP=n, CONFIG_PNP=y we get this warning:
drivers/char/tpm/tpm_tis.c:706:13: warning: 'tpm_tis_reenable_interrupts' defined but not used [-Wunused-function]
This seems to have been introduced in a2fa3fb0d 'tpm: convert tpm_tis driver
to use dev_pm_ops from legacy pm_ops'
Also, unpon reviewing, the #ifdefs around tpm_tis_pm are not right, the first
reference is protected, the second is not. tpm_tis_pm is always defined so we
can drop the #ifdef.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This consolidates everything that is only used within tpm-dev.c
into tpm-dev.c and out of the publicly visible struct tpm_chip.
The per-file allocation lays the ground work for someday fixing the
strange forced O_EXCL behaviour of the current code.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This builds on the last commit to use the ops structure in the core
and reduce the size of tpm_vendor_specific.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This replaces the static initialization of a tpm_vendor_specific
structure in the drivers with the standard Linux idiom of providing
a const structure of function pointers.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe: did apply manually due to commit
191ffc6bde3 tpm/tpm_i2c_atmel: fix coccinelle warnings]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The tpm core now sets up and controls all sysfs attributes, instead
of having each driver have a unique take on it.
All drivers now now have a uniform set of attributes, and no sysfs
related entry points are exported from the tpm core module.
This also uses the new method used to declare sysfs attributes
with DEVICE_ATTR_RO and 'struct attribute *'
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: had to apply the tpm_i2c_atmel part manually due to commit
191ffc6bde3fc tpm/tpm_i2c_atmel: fix coccinelle warnings]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
CLASS-sysfs.c is a common idiom for linux subsystems.
This is the first step to pulling all the sysfs support code from
the drivers into tpm-sysfs. This is a plain text copy from tpm-interface
with support changes to make it compile.
_tpm_pcr_read is made non-static and is called tpm_pcr_read_dev.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
CLASS-dev.c is a common idiom for Linux subsystems
This pulls all the code related to the miscdev into tpm-dev.c and makes it
static. The identical file_operation structs in the drivers are purged and the
tpm common code unconditionally creates the miscdev.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe:
tpm_dev_release is now used only in this file, thus the EXPORT_SYMBOL
can be dropped and the function be marked as static.
It has no other in-kernel users]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
“wait” wait queue is defined but never used in the function, thus
it can be removed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
drivers/char/tpm/tpm_i2c_atmel.c:178:8-9: WARNING: return of 0/1 in function 'i2c_atmel_req_canceled' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: coccinelle/misc/boolreturn.cocci
CC: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
CC: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
smatch complains:
drivers/char/tpm/tpm_ibmvtpm.c:510
ibmvtpm_crq_process() info: ignoring unreachable code.
-> The return is not necessary here, remove it
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The 'get_burstcount' function can in some circumstances 'return -EBUSY' which
in tpm_stm_i2c_send is stored in an 'u32 burstcnt'
thus converting the signed value into an unsigned value, resulting
in 'burstcnt' being huge.
Changing the type to u32 only does not solve the problem as the signed
value is converted to an unsigned in I2C_WRITE_DATA, resulting in the
same effect.
Thus
-> Change type of burstcnt to u32 (the return type of get_burstcount)
-> Add a check for the return value of 'get_burstcount' and propagate a
potential error.
This makes also sense in the 'I2C_READ_DATA' case, where the there is no
signed/unsigned conversion.
found by coverity
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
If
status = acpi_get_name(handle, ACPI_FULL_PATHNAME, &buffer);
fails for whatever reason and does not return AE_OK
if (strstr(buffer.pointer, context) != NULL) {
does dereference a null pointer.
-> Check the return value and return the status to the caller
Found by coverity
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Depending on the implementation strcmp might return the difference between
two strings not only -1,0,1 consequently
if (strcmp (a,b) == -1)
might lead to taking the wrong branch
-> compare with < 0 instead,
which in any case is more canonical.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Detecting physical presence interface features by checking availbility
of corresponding ACPI _DSM functions, it should be more accurate than
checking TPM version number.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use helper functions to simplify _DSM related code in TPM driver.
This patch also help to get rid of following warning messages:
[ 163.509575] ACPI Error: Incorrect return type [Buffer] requested [Package]
(20130517/nsxfeval-135)
But there is still an warning left.
[ 181.637366] ACPI Warning: \_SB_.IIO0.LPC0.TPM_._DSM: Argument #4 type
mismatch - Found [Buffer], ACPI requires [Package] (20130517/nsarguments-95)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When searching ACPI object for TPM device, it should match current
ACPI object name instead of the full path.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In function ppi_callback(), memory allocated by acpi_get_name() will get
leaked when current device isn't the desired TPM device, so fix the
memory leak.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The user has the option of disabling the platform driver:
00:02.0 Unassigned class [ff80]: XenSource, Inc. Xen Platform Device (rev 01)
which is used to unplug the emulated drivers (IDE, Realtek 8169, etc)
and allow the PV drivers to take over. If the user wishes
to disable that they can set:
xen_platform_pci=0
(in the guest config file)
or
xen_emul_unplug=never
(on the Linux command line)
except it does not work properly. The PV drivers still try to
load and since the Xen platform driver is not run - and it
has not initialized the grant tables, most of the PV drivers
stumble upon:
input: Xen Virtual Keyboard as /devices/virtual/input/input5
input: Xen Virtual Pointer as /devices/virtual/input/input6M
------------[ cut here ]------------
kernel BUG at /home/konrad/ssd/konrad/linux/drivers/xen/grant-table.c:1206!
invalid opcode: 0000 [#1] SMP
Modules linked in: xen_kbdfront(+) xenfs xen_privcmd
CPU: 6 PID: 1389 Comm: modprobe Not tainted 3.13.0-rc1upstream-00021-ga6c892b-dirty #1
Hardware name: Xen HVM domU, BIOS 4.4-unstable 11/26/2013
RIP: 0010:[<ffffffff813ddc40>] [<ffffffff813ddc40>] get_free_entries+0x2e0/0x300
Call Trace:
[<ffffffff8150d9a3>] ? evdev_connect+0x1e3/0x240
[<ffffffff813ddd0e>] gnttab_grant_foreign_access+0x2e/0x70
[<ffffffffa0010081>] xenkbd_connect_backend+0x41/0x290 [xen_kbdfront]
[<ffffffffa0010a12>] xenkbd_probe+0x2f2/0x324 [xen_kbdfront]
[<ffffffff813e5757>] xenbus_dev_probe+0x77/0x130
[<ffffffff813e7217>] xenbus_frontend_dev_probe+0x47/0x50
[<ffffffff8145e9a9>] driver_probe_device+0x89/0x230
[<ffffffff8145ebeb>] __driver_attach+0x9b/0xa0
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145eb50>] ? driver_probe_device+0x230/0x230
[<ffffffff8145cf1c>] bus_for_each_dev+0x8c/0xb0
[<ffffffff8145e7d9>] driver_attach+0x19/0x20
[<ffffffff8145e260>] bus_add_driver+0x1a0/0x220
[<ffffffff8145f1ff>] driver_register+0x5f/0xf0
[<ffffffff813e55c5>] xenbus_register_driver_common+0x15/0x20
[<ffffffff813e76b3>] xenbus_register_frontend+0x23/0x40
[<ffffffffa0015000>] ? 0xffffffffa0014fff
[<ffffffffa001502b>] xenkbd_init+0x2b/0x1000 [xen_kbdfront]
[<ffffffff81002049>] do_one_initcall+0x49/0x170
.. snip..
which is hardly nice. This patch fixes this by having each
PV driver check for:
- if running in PV, then it is fine to execute (as that is their
native environment).
- if running in HVM, check if user wanted 'xen_emul_unplug=never',
in which case bail out and don't load any PV drivers.
- if running in HVM, and if PCI device 5853:0001 (xen_platform_pci)
does not exist, then bail out and not load PV drivers.
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=ide-disks',
then bail out for all PV devices _except_ the block one.
Ditto for the network one ('nics').
- (v2) if running in HVM, and if the user wanted 'xen_emul_unplug=unnecessary'
then load block PV driver, and also setup the legacy IDE paths.
In (v3) make it actually load PV drivers.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it
Reported-by: Anthony PERARD <anthony.perard@citrix.com>
Reported-and-Tested-by: Fabio Fantoni <fabio.fantoni@m2r.biz>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: Add extra logic to handle the myrid ways 'xen_emul_unplug'
can be used per Ian and Stefano suggestion]
[v3: Make the unnecessary case work properly]
[v4: s/disks/ide-disks/ spotted by Fabio]
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [for PCI parts]
CC: stable@vger.kernel.org
Correct spelling typo in various part of kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fan speed can be set to off, slow, and fast, which can be exported
to userspace through the hwmon ABI as pwm1 / pwm2.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This doesn't work on Studio, XPS, Vostro, and Precision laptops,
and it doesn't provide any value except to cause confusion when
it does not work. Drop it and always use DMI BIOS version instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least on Studio 1555 and XPS M140, the fan speed is reported directly,
not with the default speed multiplier of 30. Information on the web
suggests that this may be true for other models as well, though it is
unknown at this time which systems may be affected.
Use the driver_data field of dmi_system_id to override the default fan
multiplier value for the two systems known to use a multiplier of 1.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I made enough changes to the driver to warrant adding a copyright notice.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Studio 1555 with dual-core CPU, reading sensor attributes
exported by this driver resulted in random failures combined
with system hangups and forced logouts. Information in
drivers/firmware/dcdbas.c suggests that SMM accesses must
run on CPU 0. With this patch, the problems are gone,
suggesting that this is in fact the case.
Code derived from drivers/firmware/dcdbas.c.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver version number is long since obsolete, so drop it.
Also, drop the info message at driver startup to reduce boot noise.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing the link returns a page not found error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SMM API suggests that more than one temperature sensor is supported,
so add support for them. Currently only supported for hwmon interface.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix:
WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
WARNING: __packed is preferred over __attribute__((packed))
WARNING: externs should be avoided in .c files
ERROR: spaces required around that ':' (ctx:ExV)
ERROR: do not use assignment in if condition
WARNING: line over 80 characters
WARNING: __initdata should be placed after i8k_dmi_table[]
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSogqUAAoJEHm+PkMAQRiGM2MIAJrr5KEXEWuuAR4+JkkWBK7A
+dVT4n1MM4wP/aCIyriSlq7kgT03Wxk4Q4wKsj2wZvDQkNgEQjrctgIihc75jqi5
126nmT3YXJLwgDpFA3RHZUWve3j3vfUG53rRuk7K9Xx1sGWU3Ls7BuInvQZ//+QS
6UB4UuEAalmose5U8ToXQfMqZhjwreZKeb64TEZwFvu2klv4cnka1L/zHbmQGgRg
2Pfv+aUrjsYE8s9lkEKX8MIQsDn28Q5Lsv7XIEQwo2at4rYbJaxX6usuC1OI0MQ5
BLUn1GgtvOidq6FzSg6kXiA/MJYH3J0S+p4uULWAprxA+KeJRbWNRroM94W1qAk=
=1Wcq
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc3' into drm-intel-next-queued
Linux 3.13-rc3
I need a backmerge for two reasons:
- For merging the ppgtt patches from Ben I need to pull in the bdw
support.
- We now have duplicated calls to intel_uncore_forcewake_reset in the
setup code to due 2 different patches merged into -next and 3.13.
The conflict is silen so I need the merge to be able to apply
Deepak's fixup patch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Trivial conflict, it doesn't even show up in the merge diff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing huge, just a few small bugfixes for problems reported, and a device id
update.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlKiE8QACgkQMUfUDdst+yl9dQCgwXrgSRyBlULDHOdBnKblqrMq
gYQAoLVKfuEOXRXBJOD4CzNeCMLButsM
=HbWB
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Nothing huge, just a few small bugfixes for problems reported, and a
device id update"
* tag 'char-misc-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: add 9 series PCH mei device ids
drivers/char/i8k.c: add Dell XPLS L421X
MAINTAINERS: add HSI subsystem
misc: mic: Suppress memory space sparse warnings
misc: mic: Fix endianness issues.
misc: mic: Fix user space namespace pollution from mic_common.h.
misc: mic: Bug fix for sysfs poll usage.
misc: mic: Minor bug fix in 'retry' loops.
misc: mic: Change mic_notify(...) to return true.
extcon: remove freed groups caused the panic or warning in unregister flow
extcon: arizona: Get pdata from arizona structure not device
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The drivers are long gone but some config escaped the prune
Signed-off-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=57221
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull crypto update from Herbert Xu:
- Made x86 ablk_helper generic for ARM
- Phase out chainiv in favour of eseqiv (affects IPsec)
- Fixed aes-cbc IV corruption on s390
- Added constant-time crypto_memneq which replaces memcmp
- Fixed aes-ctr in omap-aes
- Added OMAP3 ROM RNG support
- Add PRNG support for MSM SoC's
- Add and use Job Ring API in caam
- Misc fixes
[ NOTE! This pull request was sent within the merge window, but Herbert
has some questionable email sending setup that makes him public enemy
#1 as far as gmail is concerned. So most of his emails seem to be
trapped by gmail as spam, resulting in me not seeing them. - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (49 commits)
crypto: s390 - Fix aes-cbc IV corruption
crypto: omap-aes - Fix CTR mode counter length
crypto: omap-sham - Add missing modalias
padata: make the sequence counter an atomic_t
crypto: caam - Modify the interface layers to use JR API's
crypto: caam - Add API's to allocate/free Job Rings
crypto: caam - Add Platform driver for Job Ring
hwrng: msm - Add PRNG support for MSM SoC's
ARM: DT: msm: Add Qualcomm's PRNG driver binding document
crypto: skcipher - Use eseqiv even on UP machines
crypto: talitos - Simplify key parsing
crypto: picoxcell - Simplify and harden key parsing
crypto: ixp4xx - Simplify and harden key parsing
crypto: authencesn - Simplify key parsing
crypto: authenc - Export key parsing helper function
crypto: mv_cesa: remove deprecated IRQF_DISABLED
hwrng: OMAP3 ROM Random Number Generator support
crypto: sha256_ssse3 - also test for BMI2
crypto: mv_cesa - Remove redundant of_match_ptr
crypto: sahara - Remove redundant of_match_ptr
...
Pull security subsystem updates from James Morris:
"In this patchset, we finally get an SELinux update, with Paul Moore
taking over as maintainer of that code.
Also a significant update for the Keys subsystem, as well as
maintenance updates to Smack, IMA, TPM, and Apparmor"
and since I wanted to know more about the updates to key handling,
here's the explanation from David Howells on that:
"Okay. There are a number of separate bits. I'll go over the big bits
and the odd important other bit, most of the smaller bits are just
fixes and cleanups. If you want the small bits accounting for, I can
do that too.
(1) Keyring capacity expansion.
KEYS: Consolidate the concept of an 'index key' for key access
KEYS: Introduce a search context structure
KEYS: Search for auth-key by name rather than target key ID
Add a generic associative array implementation.
KEYS: Expand the capacity of a keyring
Several of the patches are providing an expansion of the capacity of a
keyring. Currently, the maximum size of a keyring payload is one page.
Subtract a small header and then divide up into pointers, that only gives
you ~500 pointers on an x86_64 box. However, since the NFS idmapper uses
a keyring to store ID mapping data, that has proven to be insufficient to
the cause.
Whatever data structure I use to handle the keyring payload, it can only
store pointers to keys, not the keys themselves because several keyrings
may point to a single key. This precludes inserting, say, and rb_node
struct into the key struct for this purpose.
I could make an rbtree of records such that each record has an rb_node
and a key pointer, but that would use four words of space per key stored
in the keyring. It would, however, be able to use much existing code.
I selected instead a non-rebalancing radix-tree type approach as that
could have a better space-used/key-pointer ratio. I could have used the
radix tree implementation that we already have and insert keys into it by
their serial numbers, but that means any sort of search must iterate over
the whole radix tree. Further, its nodes are a bit on the capacious side
for what I want - especially given that key serial numbers are randomly
allocated, thus leaving a lot of empty space in the tree.
So what I have is an associative array that internally is a radix-tree
with 16 pointers per node where the index key is constructed from the key
type pointer and the key description. This means that an exact lookup by
type+description is very fast as this tells us how to navigate directly to
the target key.
I made the data structure general in lib/assoc_array.c as far as it is
concerned, its index key is just a sequence of bits that leads to a
pointer. It's possible that someone else will be able to make use of it
also. FS-Cache might, for example.
(2) Mark keys as 'trusted' and keyrings as 'trusted only'.
KEYS: verify a certificate is signed by a 'trusted' key
KEYS: Make the system 'trusted' keyring viewable by userspace
KEYS: Add a 'trusted' flag and a 'trusted only' flag
KEYS: Separate the kernel signature checking keyring from module signing
These patches allow keys carrying asymmetric public keys to be marked as
being 'trusted' and allow keyrings to be marked as only permitting the
addition or linkage of trusted keys.
Keys loaded from hardware during kernel boot or compiled into the kernel
during build are marked as being trusted automatically. New keys can be
loaded at runtime with add_key(). They are checked against the system
keyring contents and if their signatures can be validated with keys that
are already marked trusted, then they are marked trusted also and can
thus be added into the master keyring.
Patches from Mimi Zohar make this usable with the IMA keyrings also.
(3) Remove the date checks on the key used to validate a module signature.
X.509: Remove certificate date checks
It's not reasonable to reject a signature just because the key that it was
generated with is no longer valid datewise - especially if the kernel
hasn't yet managed to set the system clock when the first module is
loaded - so just remove those checks.
(4) Make it simpler to deal with additional X.509 being loaded into the kernel.
KEYS: Load *.x509 files into kernel keyring
KEYS: Have make canonicalise the paths of the X.509 certs better to deduplicate
The builder of the kernel now just places files with the extension ".x509"
into the kernel source or build trees and they're concatenated by the
kernel build and stuffed into the appropriate section.
(5) Add support for userspace kerberos to use keyrings.
KEYS: Add per-user_namespace registers for persistent per-UID kerberos caches
KEYS: Implement a big key type that can save to tmpfs
Fedora went to, by default, storing kerberos tickets and tokens in tmpfs.
We looked at storing it in keyrings instead as that confers certain
advantages such as tickets being automatically deleted after a certain
amount of time and the ability for the kernel to get at these tokens more
easily.
To make this work, two things were needed:
(a) A way for the tickets to persist beyond the lifetime of all a user's
sessions so that cron-driven processes can still use them.
The problem is that a user's session keyrings are deleted when the
session that spawned them logs out and the user's user keyring is
deleted when the UID is deleted (typically when the last log out
happens), so neither of these places is suitable.
I've added a system keyring into which a 'persistent' keyring is
created for each UID on request. Each time a user requests their
persistent keyring, the expiry time on it is set anew. If the user
doesn't ask for it for, say, three days, the keyring is automatically
expired and garbage collected using the existing gc. All the kerberos
tokens it held are then also gc'd.
(b) A key type that can hold really big tickets (up to 1MB in size).
The problem is that Active Directory can return huge tickets with lots
of auxiliary data attached. We don't, however, want to eat up huge
tracts of unswappable kernel space for this, so if the ticket is
greater than a certain size, we create a swappable shmem file and dump
the contents in there and just live with the fact we then have an
inode and a dentry overhead. If the ticket is smaller than that, we
slap it in a kmalloc()'d buffer"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (121 commits)
KEYS: Fix keyring content gc scanner
KEYS: Fix error handling in big_key instantiation
KEYS: Fix UID check in keyctl_get_persistent()
KEYS: The RSA public key algorithm needs to select MPILIB
ima: define '_ima' as a builtin 'trusted' keyring
ima: extend the measurement list to include the file signature
kernel/system_certificate.S: use real contents instead of macro GLOBAL()
KEYS: fix error return code in big_key_instantiate()
KEYS: Fix keyring quota misaccounting on key replacement and unlink
KEYS: Fix a race between negating a key and reading the error set
KEYS: Make BIG_KEYS boolean
apparmor: remove the "task" arg from may_change_ptraced_domain()
apparmor: remove parent task info from audit logging
apparmor: remove tsk field from the apparmor_audit_struct
apparmor: fix capability to not use the current task, during reporting
Smack: Ptrace access check mode
ima: provide hash algo info in the xattr
ima: enable support for larger default filedata hash algorithms
ima: define kernel parameter 'ima_template=' to change configured default
ima: add Kconfig default measurement list template
...
the following areas: performance, avoiding waste of entropy, better
tracking of entropy estimates, support for non-x86 platforms that have
a register which can't be used for fine-grained timekeeping, but which
might be good enough for the random driver.
Also add some printk's so that we can see how quickly /dev/urandom can
get initialized, and when programs try to use /dev/urandom before it
is fully initialized (since this could be a security issue). This
shouldn't be an issue on x86 desktop/laptops --- a test on my Lenovo
T430s laptop shows that /dev/urandom is getting fully initialized
approximately two seconds before the root file system is mounted
read/write --- this may be an issue with ARM and MIPS embedded/mobile
systems, though. These printk's will be a useful canary before
potentially adding a future change to start blocking processes which
try to read from /dev/urandom before it is initialized, which is
something FreeBSD does already for security reasons, and which
security folks have been agitating for Linux to also adopt.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=wla0
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random changes from Ted Ts'o:
"The /dev/random changes for 3.13 including a number of improvements in
the following areas: performance, avoiding waste of entropy, better
tracking of entropy estimates, support for non-x86 platforms that have
a register which can't be used for fine-grained timekeeping, but which
might be good enough for the random driver.
Also add some printk's so that we can see how quickly /dev/urandom can
get initialized, and when programs try to use /dev/urandom before it
is fully initialized (since this could be a security issue). This
shouldn't be an issue on x86 desktop/laptops --- a test on my Lenovo
T430s laptop shows that /dev/urandom is getting fully initialized
approximately two seconds before the root file system is mounted
read/write --- this may be an issue with ARM and MIPS embedded/mobile
systems, though. These printk's will be a useful canary before
potentially adding a future change to start blocking processes which
try to read from /dev/urandom before it is initialized, which is
something FreeBSD does already for security reasons, and which
security folks have been agitating for Linux to also adopt"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: add debugging code to detect early use of get_random_bytes()
random: initialize the last_time field in struct timer_rand_state
random: don't zap entropy count in rand_initialize()
random: printk notifications for urandom pool initialization
random: make add_timer_randomness() fill the nonblocking pool first
random: convert DEBUG_ENT to tracepoints
random: push extra entropy to the output pools
random: drop trickle mode
random: adjust the generator polynomials in the mixing function slightly
random: speed up the fast_mix function by a factor of four
random: cap the rate which the /dev/urandom pool gets reseeded
random: optimize the entropy_store structure
random: optimize spinlock use in add_device_randomness()
random: fix the tracepoint for get_random_bytes(_arch)
random: account for entropy loss due to overwrites
random: allow fractional bits to be tracked
random: statically compute poolbitshift, poolbytes, poolbits
random: mix in architectural randomness earlier in extract_buf()
some robustness fixes for broken virtio devices, plus minor tweaks.
[vs last pull request: added the virtio-scsi broken vq escape patch, which
I somehow lost.]
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=vY2L
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing really exciting: some groundwork for changing virtio endian,
and some robustness fixes for broken virtio devices, plus minor
tweaks"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_scsi: verify if queue is broken after virtqueue_get_buf()
x86, asmlinkage, lguest: Pass in globals into assembler statement
virtio: mmio: fix signature checking for BE guests
virtio_ring: adapt to notify() returning bool
virtio_net: verify if queue is broken after virtqueue_get_buf()
virtio_console: verify if queue is broken after virtqueue_get_buf()
virtio_blk: verify if queue is broken after virtqueue_get_buf()
virtio_ring: add new function virtqueue_is_broken()
virtio_test: verify if virtqueue_kick() succeeded
virtio_net: verify if virtqueue_kick() succeeded
virtio_ring: let virtqueue_{kick()/notify()} return a bool
virtio_ring: change host notification API
virtio_config: remove virtio_config_val
virtio: use size-based config accessors.
virtio_config: introduce size-based accessors.
virtio_ring: plug kmemleak false positive.
virtio: pm: use CONFIG_PM_SLEEP instead of CONFIG_PM
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thus far we've tried to carefully work around the fact that old
userspace relied on the AGP-backed legacy buffer mapping ioctls for a
bit too long. But it's really horribly, and now some new users for it
started to show up again:
http://www.mail-archive.com/mesa-dev@lists.freedesktop.org/msg45547.html
This uses drmAgpSize to figure out the GTT size, which is both the
wrong thing to inquire and also might force us to keep this crap
around for another few years.
So I want to stop this particular zombie from raising ever again. Now
it's only been 4 years since XvMC was fixed for gen3, so a bit early
by the usual rules. But since Linus explicitly said that an ABI
breakage only counts if someone actually observes it I want to tempt
fate an accelarate the demise of AGP.
We probably need to wait 2-3 kernel releases with this shipping until
we go on a killing spree code-wise.
v2: Remove intel_agp_enabled since it's unused (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
Merge first patch-bomb from Andrew Morton:
"Quite a lot of other stuff is banked up awaiting further
next->mainline merging, but this batch contains:
- Lots of random misc patches
- OCFS2
- Most of MM
- backlight updates
- lib/ updates
- printk updates
- checkpatch updates
- epoll tweaking
- rtc updates
- hfs
- hfsplus
- documentation
- procfs
- update gcov to gcc-4.7 format
- IPC"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (269 commits)
ipc, msg: fix message length check for negative values
ipc/util.c: remove unnecessary work pending test
devpts: plug the memory leak in kill_sb
./Makefile: export initial ramdisk compression config option
init/Kconfig: add option to disable kernel compression
drivers: w1: make w1_slave::flags long to avoid memory corruption
drivers/w1/masters/ds1wm.cuse dev_get_platdata()
drivers/memstick/core/ms_block.c: fix unreachable state in h_msb_read_page()
drivers/memstick/core/mspro_block.c: fix attributes array allocation
drivers/pps/clients/pps-gpio.c: remove redundant of_match_ptr
kernel/panic.c: reduce 1 byte usage for print tainted buffer
gcov: reuse kbasename helper
kernel/gcov/fs.c: use pr_warn()
kernel/module.c: use pr_foo()
gcov: compile specific gcov implementation based on gcc version
gcov: add support for gcc 4.7 gcov format
gcov: move gcov structs definitions to a gcc version specific file
kernel/taskstats.c: return -ENOMEM when alloc memory fails in add_del_listener()
kernel/taskstats.c: add nla_nest_cancel() for failure processing between nla_nest_start() and nla_nest_end()
kernel/sysctl_binary.c: use scnprintf() instead of snprintf()
...
Pull vfs updates from Al Viro:
"All kinds of stuff this time around; some more notable parts:
- RCU'd vfsmounts handling
- new primitives for coredump handling
- files_lock is gone
- Bruce's delegations handling series
- exportfs fixes
plus misc stuff all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (101 commits)
ecryptfs: ->f_op is never NULL
locks: break delegations on any attribute modification
locks: break delegations on link
locks: break delegations on rename
locks: helper functions for delegation breaking
locks: break delegations on unlink
namei: minor vfs_unlink cleanup
locks: implement delegations
locks: introduce new FL_DELEG lock flag
vfs: take i_mutex on renamed file
vfs: rename I_MUTEX_QUOTA now that it's not used for quotas
vfs: don't use PARENT/CHILD lock classes for non-directories
vfs: pull ext4's double-i_mutex-locking into common code
exportfs: fix quadratic behavior in filehandle lookup
exportfs: better variable name
exportfs: move most of reconnect_path to helper function
exportfs: eliminate unused "noprogress" counter
exportfs: stop retrying once we race with rename/remove
exportfs: clear DISCONNECTED on all parents sooner
exportfs: more detailed comment for path_reconnect
...
The CONFIG_HPET_MMAP Kconfig option exposes the memory map of the HPET
registers to userspace. The Kconfig help points out that in some cases
this can be a security risk as some systems may erroneously configure the
map such that additional data is exposed to userspace.
This is a problem for distributions -- some users want the MMAP
functionality but it comes with a significant security risk. In an effort
to mitigate this risk, and due to the low number of users of the MMAP
functionality, I've introduced a kernel parameter, hpet_mmap_enable, that
is required in order to actually have the HPET MMAP exposed.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Matt Wilson <msw@amazon.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Pull powerpc updates from Benjamin Herrenschmidt:
"The bulk of this is LE updates. One should now be able to build an LE
kernel and even run some things in it.
I'm still sitting on a handful of patches to enable the new ABI that I
*might* still send this merge window around, but due to the
incertainty (they are pretty fresh) I want to keep them separate.
Other notable changes are some infrastructure bits to better handle
PCI pass-through under KVM, some bits and pieces added to the new
PowerNV platform support such as access to the CPU SCOM bus via sysfs,
and support for EEH error handling on PHB3 (Power8 PCIe).
We also grew arch_get_random_long() for both pseries and powernv when
running on P7+ and P8, exploiting the HW rng.
And finally various embedded updates from freescale"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (154 commits)
powerpc: Fix fatal SLB miss when restoring PPR
powerpc/powernv: Reserve the correct PE number
powerpc/powernv: Add PE to its own PELTV
powerpc/powernv: Add support for indirect XSCOM via debugfs
powerpc/scom: Improve debugfs interface
powerpc/scom: Enable 64-bit addresses
powerpc/boot: Properly handle the base "of" boot wrapper
powerpc/bpf: Support MOD operation
powerpc/bpf: Fix DIVWU instruction opcode
of: Move definition of of_find_next_cache_node into common code.
powerpc: Remove big endianness assumption in of_find_next_cache_node
powerpc/tm: Remove interrupt disable in __switch_to()
powerpc: word-at-a-time optimization for 64-bit Little Endian
powerpc/bpf: BPF JIT compiler for 64-bit Little Endian
powerpc: Only save/restore SDR1 if in hypervisor mode
powerpc/pmu: Fix ADB_PMU_LED_IDE dependencies
powerpc/nvram: Fix endian issue when using the partition length
powerpc/nvram: Fix endian issue when reading the NVRAM size
powerpc/nvram: Scan partitions only once
powerpc/mpc512x: remove unnecessary #if
...
The Tausworthe PRNG is initialized at late_initcall time. At that time the
entropy pool serving get_random_bytes is not filled sufficiently. This
patch adds an additional reseeding step as soon as the nonblocking pool
gets marked as initialized.
On some machines it might be possible that late_initcall gets called after
the pool has been initialized. In this situation we won't reseed again.
(A call to prandom_seed_late blocks later invocations of early reseed
attempts.)
Joint work with Daniel Borkmann.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b5b4bb3f6a (of: only include prom.h on sparc) removed implicit
includes of of_*.h headers by powerpc's prom.h. Some components were
missed in initial clean-up patch, so add the necessary includes to fix
powerpc builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-ide@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
We only depend on the intel-gtt module for GTT frobbign on older gens.
The intel_agp module is optional, except for UMS and some old XvMC
userland on gen3. So make AGP support optional. As before, we will
fail the i915 init for UMS and gen3 KMS the same as before if
intel_agp isn't around.
intel-gtt.c is left with a somewhat ugly ifdef mess, but I'm going
to save that for a later cleaning.
At least my gen2 still works with the patch and CONFIG_AGP=n.
v2: Make i915 depend on X86 and PCI, and intel-gtt depend on PCI
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we initialize jiffies to wrap five minutes before boot (see
INITIAL_JIFFIES defined in include/linux/jiffies.h) it's important to
make sure the last_time field is initialized to INITIAL_JIFFIES.
Otherwise, the entropy estimator will overestimate the amount of
entropy resulting from the first call to add_timer_randomness(),
generally by about 8 bits.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The rand_initialize() function was being run fairly late in the kernel
boot sequence. This was unfortunate, since it zero'ed the entropy
counters, thus throwing away credit that was accumulated earlier in
the boot sequence, and it also meant that initcall functions run
before rand_initialize were using a minimally initialized pool.
To fix this, fix init_std_data() to no longer zap the entropy counter;
it wasn't necessary, and move rand_initialize() to be an early
initcall.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Print a notification to the console when the nonblocking pool is
initialized. Also printk a warning when a process tries reading from
/dev/urandom before it is fully initialized.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Change add_timer_randomness() so that it directs incoming entropy to
the nonblocking pool first if it hasn't been fully initialized yet.
This matches the strategy we use in add_interrupt_randomness(), which
allows us to push the randomness where we need it the most during when
the system is first booting up, so that get_random_bytes() and
/dev/urandom become safe to use as soon as possible.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This adds a driver for hardware random number generator present
on Qualcomm MSM SoC's.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If virtqueue_get_buf() returns with a NULL pointer it should be verified
if the virtqueue is broken, in order to avoid loop calling cpu_relax().
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch changes the displayed module name from
tpm_tis_i2c_infineon to its actual name tpm_i2c_infineon.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This is based on the work of Teddy Reed <teddy@prosauce.org> published
on GitHub:
https://github.com/theopolis/tpm-i2c-atmel.git
34894b988b67e0ae55088d6388e77b0dbf10c07d
That driver was never merged, I have taken it as a starting port,
forward ported, tested and revised the driver:
- Make it broadly textually similar to the Infineon and Nuvoton I2C
driver
- Place everything in a format suitable for mainline inclusion
- Use high level I2C functions i2c_master_send and
i2c_master_recv for data xfer
- Use the timeout system from the core code, by faking out a status
register
- Only I2C transfer the number of bytes in the reply, not a fixed
message size.
- checkpatch cleanups
- Testing on ARM Kirkwood, with this device tree, using a
AT97SC3204T-X1A180
tpm@29 {
compatible = "atmel,at97sc3204t";
reg = <0x29>;
};
Signed-off-by: Teddy Reed <teddy@prosauce.org>
[jgg: revised and tested]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor whitespace changes]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This chip is/was also branded as a Winbond WPCT301.
Originally written by Dan Morav <dmorav@nuvoton.com> and posted to LKML:
https://lkml.org/lkml/2011/9/7/206
The original posting was not merged, I have taken it as a
starting point, forward ported, tested and revised the driver:
- Rework interrupt handling to work properly with level triggered
interrupts. The old version just locked up.
- Synchronize various items with Peter Huewe's Infineon driver:
* Add durations/timeouts sysfs calls
* Remove I2C device auto-detection
* Don't fiddle with chip->release
* Call tpm_dev_vendor_release in the probe error path
* Use MODULE_DEVICE_TABLE for the I2C ids
* Provide OF compatible strings for DT support
* Use SIMPLE_DEV_PM_OPS
* Use module_i2c_driver
- checkpatch cleanups
- Testing on ARM Kirkwood with GPIO interrupts, with this device tree:
tpm@57 {
compatible = "nuvoton,npct501";
reg = <0x57>;
interrupt-parent = <&gpio1>;
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
};
Signed-off-by: Dan Morav <dmorav@nuvoton.com>
[jgg: revised and tested]
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor whitespace changes, fixed module name in kconfig]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Now that we can have multiple .c files in the tpm module there is
no reason for tpm-bios.
tpm-bios exported several functions: tpm_bios_log_setup,
tpm_bios_log_teardown, tpm_add_ppi, and tpm_remove_ppi.
They are only used by tpm, and if tpm-bios is built then
tpm will unconditionally require them. Further, tpm-bios does
nothing on its own, it has no module_init function.
Thus we remove the exports and merge the modules to simplify things.
The Makefile conditions are changed slightly to match the code,
tpm_ppi is always required if CONFIG_ACPI is set.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
This is preparation for making the tpm module multi-file. kbuild does
not like having a .c file with the same name as a module. We wish to
keep the tpm module name so that userspace doesn't see this change.
tpm-interface.c is chosen because the next several commits in the series
migrate items into tpm-sysfs.c, tpm-dev.c and tpm-class.c. All that will
be left is tpm command processing and interfacing code.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
before we rename the file it might be a good idea to cleanup the long
persisting checkpatch warnings.
Since everything is really trivial, splitting the patch up would only
result in noise.
For the interested reader - here the checkpatch warnings:
(regrouped for easer readability)
ERROR: trailing whitespace
+ * Specifications at www.trustedcomputinggroup.org^I $
+ * $
+^I/* $
+^I parameters (RSA 12->bytes: keybit, #primes, expbit) $
WARNING: unnecessary whitespace before a quoted newline
+ "invalid count value %x %zx \n", count, bufsiz);
ERROR: do not use assignment in if condition
+ if ((rc = chip->vendor.send(chip, (u8 *) buf, count)) < 0) {
ERROR: space required after that ',' (ctx:VxV)
+ len = tpm_transmit(chip,(u8 *) cmd, len);
^
ERROR: "foo * bar" should be "foo *bar"
+ssize_t tpm_show_enabled(struct device * dev, struct device_attribute * attr,
+ssize_t tpm_show_enabled(struct device * dev, struct device_attribute * attr,
+ssize_t tpm_show_active(struct device * dev, struct device_attribute * attr,
+ssize_t tpm_show_active(struct device * dev, struct device_attribute * attr,
+ssize_t tpm_show_owned(struct device * dev, struct device_attribute * attr,
+ssize_t tpm_show_owned(struct device * dev, struct device_attribute * attr,
+ssize_t tpm_show_temp_deactivated(struct device * dev,
+ struct device_attribute * attr, char *buf)
WARNING: please, no space before tabs
+ * @chip_num: ^Itpm idx # or ANY$
+ * @res_buf: ^ITPM_PCR value$
+ * ^I^Isize of res_buf is 20 bytes (or NULL if you don't care)$
+ * @chip_num: ^Itpm idx # or AN&$
+ * @hash: ^Ihash value used to extend pcr value$
ERROR: code indent should use tabs where possible
+^I TPM_ORD_CONTINUE_SELFTEST);$
WARNING: line over 80 characters
+static bool wait_for_tpm_stat_cond(struct tpm_chip *chip, u8 mask, bool check_cancel,
ERROR: trailing whitespace
+ * Called from tpm_<specific>.c probe function only for devices $
total: 16 errors, 7 warnings, 1554 lines checked
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The version of the TPM should not depend on the bus it is connected
through. 1.1, 1.2 and soon 2.0 TPMS will be all be able to use the
same bus interfaces.
Make tpm_show_caps try the 1.2 capability first. If that fails then
fall back to the 1.1 capability. This effectively auto-detects what
interface the TPM supports at run-time.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
For some reason this driver thinks that chip->data_buffer needs
to be set before it can call tpm_pm_*. This is not true. data_buffer
is used only by /dev/tpmX, which is why it is managed exclusively
by the fops functions.
Cc: Mathias Leblanc <mathias.leblanc@st.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
TPM drivers should not call dev_set_drvdata (or aliases), only the core
code is allowed to call dev_set_drvdata, and it does it during
tpm_register_hardware.
These extra sets are harmless, but are an anti-pattern that many drivers
have copied.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
misc_open sets the file->private_date to the misc_dev when calling
open. We can use container_of to go from the misc_dev back to the
tpm_chip.
Future clean ups will move tpm_open into a new file and this change
means we do not have to export the tpm_chip list.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Just put the memory directly in the chip structure, rather than
in a 2nd dedicated kmalloc.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Commit e0dd03caf2 ("tpm: return chip from
tpm_register_hardware") changed the code path here so that
ateml_get_base_addr no longer directly altered the tpm_vendor_specific
structure, and instead placed the base address on the stack.
The commit missed updating the request_region call, which would have
resulted in request_region being called with 0 as the base address.
I don't know if request_region(0, ..) will fail, if so the
driver has been broken since 2006 and we should remove it
from the tree as it has no users.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This suppresses compile warnings on 32 bit builds.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Ashley Lai <adlai@linux.vnet.ibm.com>
This lets the transport do endian conversion if necessary, and insulates
the drivers from the difference.
Most drivers can use the simple helpers virtio_cread() and virtio_cwrite().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver provides kernel-side support for the Random Number
Generator hardware found on OMAP34xx processors.
This driver comes from Maemo 2.6.28 kernel and was tested on Nokia RX-51.
It is platform device because it needs board specific function for smc calls.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=wJOk
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.12-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Stefano Stabellini:
"A small fix for Xen on x86_32 and a build fix for xen-tpmfront on
arm64"
* tag 'stable/for-linus-3.12-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Fix possible user space selector corruption
tpm: xen-tpmfront: fix missing declaration of xen_domain
Add a driver for the hwrng found in power7+ systems, based on the
existing code for the arch_get_random_long() hook.
We only register a single instance of the driver, not one per device,
because we use the existing per_cpu array of devices in the arch code.
This means we always read from the "closest" device, avoiding inter-chip
memory traffic.
Signed-off-by: Guo Chao <yan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We don't expect to get errors from the hypervisor when reading the rng,
but if we do we should pass the error up to the hwrng driver. Otherwise
the hwrng driver will continue calling us forever.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
non-x86 platforms, in particular MIPS and ARM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=qnTe
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random changes from Ted Ts'o:
"These patches are designed to enable improvements to /dev/random for
non-x86 platforms, in particular MIPS and ARM"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: allow architectures to optionally define random_get_entropy()
random: run random_int_secret_init() run after all late_initcalls
Instead of using the random driver's ad-hoc DEBUG_ENT() mechanism, use
tracepoints instead. This allows for a much more fine-grained control
of which debugging mechanism which a developer might need, and unifies
the debugging messages with all of the existing tracepoints.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
As the input pool gets filled, start transfering entropy to the output
pools until they get filled. This allows us to use the output pools
to store more system entropy. Waste not, want not....
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The add_timer_randomness() used to drop into trickle mode when entropy
pool was estimated to be 87.5% full. This was important when
add_timer_randomness() was used to sample interrupts. It's not used
for this any more --- add_interrupt_randomness() now uses fast_mix()
instead. By elimitating trickle mode, it allows us to fully utilize
entropy provided by add_input_randomness() and add_disk_randomness()
even when the input pool is above the old trickle threshold of 87.5%.
This helps to answer the criticism in [1] in their hypothetical
scenario where our entropy estimator was inaccurate, even though the
measurements in [2] seem to indicate that our entropy estimator given
real-life entropy collection is actually pretty good, albeit on the
conservative side (which was as it was designed).
[1] http://eprint.iacr.org/2013/338.pdf
[2] http://eprint.iacr.org/2012/251.pdf
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Our mixing functions were analyzed by Lacharme, Roeck, Strubel, and
Videau in their paper, "The Linux Pseudorandom Number Generator
Revisited" (see: http://eprint.iacr.org/2012/251.pdf).
They suggested a slight change to improve our mixing functions
slightly. I also adjusted the comments to better explain what is
going on, and to document why the polynomials were changed.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
By mixing the entropy in chunks of 32-bit words instead of byte by
byte, we can speed up the fast_mix function significantly. Since it
is called on every single interrupt, on systems with a very heavy
interrupt load, this can make a noticeable difference.
Also fix a compilation warning in add_interrupt_randomness() and avoid
xor'ing cycles and jiffies together just in case we have an
architecture which tries to define random_get_entropy() by returning
jiffies.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Jörn Engel <joern@logfs.org>
In order to avoid draining the input pool of its entropy at too high
of a rate, enforce a minimum time interval between reseedings of the
urandom pool. This is set to 60 seconds by default.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The add_device_randomness() function calls mix_pool_bytes() twice for
the input pool and the non-blocking pool, for a total of four times.
By using _mix_pool_byte() and taking the spinlock in
add_device_randomness(), we can halve the number of times we need
take each pool's spinlock.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Fix a problem where get_random_bytes_arch() was calling the tracepoint
get_random_bytes(). So add a new tracepoint for
get_random_bytes_arch(), and make get_random_bytes() and
get_random_bytes_arch() call their correct tracepoint.
Also, add a new tracepoint for add_device_randomness()
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When we write entropy into a non-empty pool, we currently don't
account at all for the fact that we will probabilistically overwrite
some of the entropy in that pool. This means that unless the pool is
fully empty, we are currently *guaranteed* to overestimate the amount
of entropy in the pool!
Assuming Shannon entropy with zero correlations we end up with an
exponentally decaying value of new entropy added:
entropy <- entropy + (pool_size - entropy) *
(1 - exp(-add_entropy/pool_size))
However, calculations involving fractional exponentials are not
practical in the kernel, so apply a piecewise linearization:
For add_entropy <= pool_size/2 then
(1 - exp(-add_entropy/pool_size)) >= (add_entropy/pool_size)*0.7869...
... so we can approximate the exponential with
3/4*add_entropy/pool_size and still be on the
safe side by adding at most pool_size/2 at a time.
In order for the loop not to take arbitrary amounts of time if a bad
ioctl is received, terminate if we are within one bit of full. This
way the loop is guaranteed to terminate after no more than
log2(poolsize) iterations, no matter what the input value is. The
vast majority of the time the loop will be executed exactly once.
The piecewise linearization is very conservative, approaching 3/4 of
the usable input value for small inputs, however, our entropy
estimation is pretty weak at best, especially for small values; we
have no handle on correlation; and the Shannon entropy measure (Rényi
entropy of order 1) is not the correct one to use in the first place,
but rather the correct entropy measure is the min-entropy, the Rényi
entropy of infinite order.
As such, this conservatism seems more than justified.
This does introduce fractional bit values. I have left it to have 3
bits of fraction, so that with a pool of 2^12 bits the multiply in
credit_entropy_bits() can still fit into an int, as 2*(3+12) < 31. It
is definitely possible to allow for more fractional accounting, but
that multiply then would have to be turned into a 32*32 -> 64 multiply.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: DJ Johnston <dj.johnston@intel.com>
Allow fractional bits of entropy to be tracked by scaling the entropy
counter (fixed point). This will be used in a subsequent patch that
accounts for entropy lost due to overwrites.
[ Modified by tytso to fix up a few missing places where the
entropy_count wasn't properly converted from fractional bits to
bits. ]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Use a macro to statically compute poolbitshift (will be used in a
subsequent patch), poolbytes, and poolbits. On virtually all
architectures the cost of a memory load with an offset is the same as
the one of a memory load.
It is still possible for this to generate worse code since the C
compiler doesn't know the fixed relationship between these fields, but
that is somewhat unlikely.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Previously if CPU chip had a built-in random number generator (i.e.,
RDRAND on newer x86 chips), we mixed it in at the very end of
extract_buf() using an XOR operation.
We now mix it in right after the calculate a hash across the entire
pool. This has the advantage that any contribution of entropy from
the CPU's HWRNG will get mixed back into the pool. In addition, it
means that if the HWRNG has any defects (either accidentally or
maliciously introduced), this will be mitigated via the non-linear
transform of the SHA-1 hash function before we hand out generated
output.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Allow architectures which have a disabled get_cycles() function to
provide a random_get_entropy() function which provides a fine-grained,
rapidly changing counter that can be used by the /dev/random driver.
For example, an architecture might have a rapidly changing register
used to control random TLB cache eviction, or DRAM refresh that
doesn't meet the requirements of get_cycles(), but which is good
enough for the needs of the random driver.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
xen-tpmfront fails to build on arm64 with the following error:
drivers/char/tpm/xen-tpmfront.c: In function ‘xen_tpmfront_init’:
drivers/char/tpm/xen-tpmfront.c:422:2: error: implicit declaration of function ‘xen_domain’ [-Werror=implicit-function-declaration]
Add include of xen/xen.h to fix this.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Acked-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Cc: Leonidas Da Silva Barbosa <leosilva@linux.vnet.ibm.com>
Cc: Rajiv Andrade <mail@srajiv.net>
Cc: Marcel Selhorst <tpmdd@selhorst.net>
Cc: Sirrix AG <tpmdd@sirrix.com>
Cc: tpmdd-devel@lists.sourceforge.net
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
We don't expect to get errors from the hypervisor when reading the rng,
but if we do we should pass the error up to the hwrng driver. Otherwise
the hwrng driver will continue calling us forever.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need/want the mei fixes in here so we can apply other updates that
are depending on them.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change improves code readability & is less error-prone.
For example: case adding more error paths one should remember to call 'mutex_unlock'
Signed-off-by: Elad Wexler <elad.wexler@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixmem32 is assigned to address of res->data member
so the address is always valid
Actually since we are not checking for res != NULL
static analyzing is complaining about referencing the pointer
and consequent check for null.
The code snippet looks confusing also for human eyes.
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix PV spinlocks triggering jump_label code bug
- Remove extraneous code in the tpm front driver
- Fix ballooning out of pages when non-preemptible
- Fix deadlock when using a 32-bit initial domain with large amount of memory.
- Add xen_nopvpsin parameter to the documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQvzCAAoJEFjIrFwIi8fJyCIIAMENABapdLhrOiRdQ1Y7T5v1
4bogPDLwpVxHzwo/vnHcNpl35/dUZrC6wQa51Bkoqq0V8o1XmjFy3SY/EBGjEAvw
hh4qxGY0p0NNi6hKrWC8mH9u2TcluZGm1uecabkXUhl9mrAB5oBsfJdbBZ5N69gO
QXXt0j7Xwv1APwH86T0e1Lz+lulhdw2ItXP4osYkEbRYNSaaGnuwsd0Jxcb4DeMk
qhKgP7QMn3C7zDDaapJo1axeYQRBNEtv5M8+0wwMleX4yX1+IBRZeQTsRfMr7RB/
8FhssWiH15xU6Gmzgi/VR8xhTEIbQh5GWsVReGf6pqIYSxGSYTvvyhm0bVRH4JI=
=c+7u
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.12-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Konrad Rzeszutek Wilk:
"Bug-fixes and one update to the kernel-paramters.txt documentation.
- Fix PV spinlocks triggering jump_label code bug
- Remove extraneous code in the tpm front driver
- Fix ballooning out of pages when non-preemptible
- Fix deadlock when using a 32-bit initial domain with large amount
of memory
- Add xen_nopvpsin parameter to the documentation"
* tag 'stable/for-linus-3.12-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/spinlock: Document the xen_nopvspin parameter.
xen/p2m: check MFN is in range before using the m2p table
xen/balloon: don't alloc page while non-preemptible
xen: Do not enable spinlocks before jump_label_init() has executed
tpm: xen-tpmfront: Remove the locality sysfs attribute
tpm: xen-tpmfront: Fix default durations
Upon deeper review it was agreed to remove the driver-unique
'locality' sysfs attribute before it is present in a released
kernel.
The attribute was introduced in e2683957fb
during the 3.12 merge window, so this patch needs to go in before
3.12 is released.
The hope is to have a well defined locality API that all the other
locality aware drivers can use, perhaps in 3.13.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
All the default durations were being set to 10 minutes which is
way too long for the timeouts. Normal values for the longest
duration are around 5 mins, and short duration ar around .5s.
Further, these are just the default, tpm_get_timeouts will set
them to values from the TPM (or throw an error).
Just remove them.
Acked-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The some platforms (e.g., ARM) initializes their clocks as
late_initcalls for some unknown reason. So make sure
random_int_secret_init() is run after all of the late_initcalls are
run.
Cc: stable@vger.kernel.org
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The freeze and restore functions defined in virtio drivers are used
for suspend and hibernate, so CONFIG_PM_SLEEP is more appropriate than
CONFIG_PM. This patch replace all CONFIG_PM with CONFIG_PM_SLEEP for
virtio drivers that implement freeze and restore callbacks.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It is only used in modular builds.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CC:stable. But for that reason, I did a merge with master partway
through to avoid an unnecessary conflict.
Also: a fun lguest bug turns out if you don't clear the TF flag when trapping
Bad Things happen to the guest kernel as the stack overflows...
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MFZ1
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio update from Rusty Russell:
"More console fixes; these are the theoretical ones which didn't get
CC:stable. But for that reason, I did a merge with master partway
through to avoid an unnecessary conflict.
Also: a fun lguest bug turns out if you don't clear the TF flag when
trapping Bad Things happen to the guest kernel as the stack
overflows..."
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_pci: pm: Use CONFIG_PM_SLEEP instead of CONFIG_PM
lguest: fix GPF in guest when using gdb.
lguest: fix guest kernel stack overflow when TF bit set.
lguest: fix BUG_ON() in invalid guest page table.
virtio: console: prevent use-after-free of port name in port unplug
virtio: console: cleanup an error message
virtio: console: fix locking around send_sigio_to_port()
virtio: console: add locking in port unplug path
virtio: console: add locks around buffer removal in port unplug path
tools/lguest: offer VIRTIO_F_ANY_LAYOUT for net device.
virtio tools: add .gitignore
lguest: Point to the right directory for the lguest launcher
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSGqS5AAoJEHm+PkMAQRiGFxEH/3VrqF6WAkcviNiW/0DCdO8k
v6Wi7Sp5LxVkwzmOCHCV1tTHwLRlH3cB9YmJlGQ0kHCREaAuEQAB0xJXIW7dnyYj
Qq7KoRZEMe3wizmjEsj8qsrhfMLzHjBw67hBz2znwW/4P7YdgzwD7KRiEat+yRC9
ON3nNL2zIqpfk92RXvVrSVl4KMEM+WNbOfiffgBiEP24Ja1MJMFH1d4i6hNOaB0x
9Pb3Lw8let92x+8Ao5jnjKdKMgVsoZWbN/TgQR8zZOHM38AGGiDgk18vMz+L+hpS
jqfjckxj1m30jGq0qZ9ZbMZx3IGif4KccVr30MqNHJpwi6Q24qXvT3YfA3HkstM=
=nAab
-----END PGP SIGNATURE-----
Merge tag 'v3.11-rc7' into stable/for-linus-3.12
Linux 3.11-rc7
As we need the git commit 28817e9de4f039a1a8c1fe1df2fa2df524626b9e
Author: Chuck Anderson <chuck.anderson@oracle.com>
Date: Tue Aug 6 15:12:19 2013 -0700
xen/smp: initialize IPI vectors before marking CPU online
* tag 'v3.11-rc7': (443 commits)
Linux 3.11-rc7
ARC: [lib] strchr breakage in Big-endian configuration
VFS: collect_mounts() should return an ERR_PTR
bfs: iget_locked() doesn't return an ERR_PTR
efs: iget_locked() doesn't return an ERR_PTR()
proc: kill the extra proc_readfd_common()->dir_emit_dots()
cope with potentially long ->d_dname() output for shmem/hugetlb
usb: phy: fix build breakage
USB: OHCI: add missing PCI PM callbacks to ohci-pci.c
staging: comedi: bug-fix NULL pointer dereference on failed attach
lib/lz4: correct the LZ4 license
memcg: get rid of swapaccount leftovers
nilfs2: fix issue with counting number of bio requests for BIO_EOPNOTSUPP error detection
nilfs2: remove double bio_put() in nilfs_end_bio_write() for BIO_EOPNOTSUPP error
drivers/platform/olpc/olpc-ec.c: initialise earlier
ipv4: expose IPV4_DEVCONF
ipv6: handle Redirect ICMP Message with no Redirected Header option
be2net: fix disabling TX in be_close()
Revert "ACPI / video: Always call acpi_video_init_brightness() on init"
Revert "genetlink: fix family dump race"
...
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.12:
- Added MODULE_SOFTDEP to allow pre-loading of modules.
- Reinstated crct10dif driver using the module softdep feature.
- Allow via rng driver to be auto-loaded.
- Split large input data when necessary in nx.
- Handle zero length messages correctly for GCM/XCBC in nx.
- Handle SHA-2 chunks bigger than block size properly in nx.
- Handle unaligned lengths in omap-aes.
- Added SHA384/SHA512 to omap-sham.
- Added OMAP5/AM43XX SHAM support.
- Added OMAP4 TRNG support.
- Misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (66 commits)
Reinstate "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
hwrng: via - Add MODULE_DEVICE_TABLE
crypto: fcrypt - Fix bitoperation for compilation with clang
crypto: nx - fix SHA-2 for chunks bigger than block size
crypto: nx - fix GCM for zero length messages
crypto: nx - fix XCBC for zero length messages
crypto: nx - fix limits to sg lists for AES-CCM
crypto: nx - fix limits to sg lists for AES-XCBC
crypto: nx - fix limits to sg lists for AES-GCM
crypto: nx - fix limits to sg lists for AES-CTR
crypto: nx - fix limits to sg lists for AES-CBC
crypto: nx - fix limits to sg lists for AES-ECB
crypto: nx - add offset to nx_build_sg_lists()
padata - Register hotcpu notifier after initialization
padata - share code between CPU_ONLINE and CPU_DOWN_FAILED, same to CPU_DOWN_PREPARE and CPU_UP_CANCELED
hwrng: omap - reorder OMAP TRNG driver code
crypto: omap-sham - correct dma burst size
crypto: omap-sham - Enable Polling mode if DMA fails
crypto: tegra-aes - bitwise vs logical and
crypto: sahara - checking the wrong variable
...
Merge IPMI fixes from:
"A few things for 3.12 from various people"
* emailed patches from Corey Minyard <minyard@acm.org>:
BMC support for PARISC machines
Add MODULE_ALIAS for autoloading ipmi driver on ACPI systems
ipmi: Initialize locals to avoid warning
ipmi: info leak in compat_ipmi_ioctl()
The last line of PARISC machines (C8000, RP34x0, etc.) have a BMC for
controlling temperature, fan speed and other stuff. The BMC is
connected via a special bus and listed in the firmware device tree.
This change adds support for these BMCs to the IPMI driver.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'd submitted this about a year ago but it never made it upstream.
The latest versions of the kernel drivers for ipmi can use ACPI to
determine the type of BMC device used in the system. The following
patch adds a module alias so that udev will autoload the ipmi_si driver.
Signed-off-by: Jordan Hargrave <jordan_hargrave@dell.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A couple of variables were getting warnings about being uninitialized.
It was a false warning, but initialize them, anyway.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86_64 there is a 4 byte hole between ->recv_type and ->addr.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Xen Trusted Platform Module (TPM) frontend driver - with the backend in MiniOS.
- Scalability improvements in event channel.
- Two extra Xen co-maintainers (David, Boris) and one going away (Jeremy)
Bug-fixes:
- Make the 1:1 mapping work during early bootup on selective regions.
- Add scratch page to balloon driver to deal with unexpected code still holding
on stale pages.
- Allow NMIs on PV guests (64-bit only)
- Remove unnecessary TLB flush in M2P code.
- Fixes duplicate callbacks in Xen granttable code.
- Fixes in PRIVCMD_MMAPBATCH ioctls to allow retries
- Fix for events being lost due to rescheduling on different VCPUs.
- More documentation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSJgGgAAoJEFjIrFwIi8fJ4asH+gKp0aauPEdHtmn7rLfZUUJ5
uuvWBiXiVVYMFz81NXlZ1WoAMuDuVA45Eu785uPRb9oUHDi0W8LO4Dqr+9lJTrXJ
KiMvTXmOLSfSdjRlDI4jCoxBdg8tpbT3oJkXsFcHnrd5d4oTFGb0uuo5nFYPDicZ
BGogDclzcqtlYl/2LUb+6vUXUQd77n0oW7RQ4yAaw3Qdj381om3Dmoeat8QU9Kdo
Q4dhsHS6YAGR5R+G0zPfVOoKvSGoGV0NUdXr19QpYArGxKXcmiPjrgAJ/NGLsxvm
8AbPjmQzOFJmUclHiiej6kvBsh2ZTYAesJMSAFLWD7EndXii7zljyJv0PIJ//uQ=
=hNDW
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.12-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from Konrad Rzeszutek Wilk:
"A couple of features and a ton of bug-fixes. There is also some
maintership changes. Jeremy is enjoying the full-time work at the
startup and as much as he would love to help - he can't find the time.
I have a bunch of other things that I promised to work on - paravirt
diet, get SWIOTLB working everywhere, etc, but haven't been able to
find the time.
As such both David Vrabel and Boris Ostrovsky have graciously
volunteered to help with the maintership role. They will keep the lid
on regressions, bug-fixes, etc. I will be in the background to help -
but eventually there will be less of me doing the Xen GIT pulls and
more of them. Stefano is still doing the ARM/ARM64 and will continue
on doing so.
Features:
- Xen Trusted Platform Module (TPM) frontend driver - with the
backend in MiniOS.
- Scalability improvements in event channel.
- Two extra Xen co-maintainers (David, Boris) and one going away (Jeremy)
Bug-fixes:
- Make the 1:1 mapping work during early bootup on selective regions.
- Add scratch page to balloon driver to deal with unexpected code
still holding on stale pages.
- Allow NMIs on PV guests (64-bit only)
- Remove unnecessary TLB flush in M2P code.
- Fixes duplicate callbacks in Xen granttable code.
- Fixes in PRIVCMD_MMAPBATCH ioctls to allow retries
- Fix for events being lost due to rescheduling on different VCPUs.
- More documentation"
* tag 'stable/for-linus-3.12-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (23 commits)
hvc_xen: Remove unnecessary __GFP_ZERO from kzalloc
drivers/xen-tpmfront: Fix compile issue with missing option.
xen/balloon: don't set P2M entry for auto translated guest
xen/evtchn: double free on error
Xen: Fix retry calls into PRIVCMD_MMAPBATCH*.
xen/pvhvm: Initialize xen panic handler for PVHVM guests
xen/m2p: use GNTTABOP_unmap_and_replace to reinstate the original mapping
xen: fix ARM build after 6efa20e4
MAINTAINERS: Remove Jeremy from the Xen subsystem.
xen/events: document behaviour when scanning the start word for events
x86/xen: during early setup, only 1:1 map the ISA region
x86/xen: disable premption when enabling local irqs
swiotlb-xen: replace dma_length with sg_dma_len() macro
swiotlb: replace dma_length with sg_dma_len() macro
xen/balloon: set a mapping for ballooned out pages
xen/evtchn: improve scalability by using per-user locks
xen/p2m: avoid unneccesary TLB flush in m2p_remove_override()
MAINTAINERS: Add in two extra co-maintainers of the Xen tree.
MAINTAINERS: Update the Xen subsystem's with proper mailing list.
xen: replace strict_strtoul() with kstrtoul()
...
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
1) ACPI-based PCI hotplug (ACPIPHP) subsystem rework and introduction
of Intel Thunderbolt support on systems that use ACPI for signalling
Thunderbolt hotplug events. This also should make ACPIPHP work in
some cases in which it was known to have problems. From
Rafael J Wysocki, Mika Westerberg and Kirill A Shutemov.
2) ACPI core code cleanups and dock station support cleanups from
Jiang Liu and Rafael J Wysocki.
3) Fixes for locking problems related to ACPI device hotplug from
Rafael J Wysocki.
4) ACPICA update to version 20130725 includig fixes, cleanups, support
for more than 256 GPEs per GPE block and a change to make the ACPI
PM Timer optional (we've seen systems without the PM Timer in the
field already). One of the fixes, related to the DeRefOf operator,
is necessary to prevent some Windows 8 oriented AML from causing
problems to happen. From Bob Moore, Lv Zheng, and Jung-uk Kim.
5) Removal of the old and long deprecated /proc/acpi/event interface
and related driver changes from Thomas Renninger.
6) ACPI and Xen changes to make the reduced hardware sleep work with
the latter from Ben Guthro.
7) ACPI video driver cleanups and a blacklist of systems that should
not tell the BIOS that they are compatible with Windows 8 (or ACPI
backlight and possibly other things will not work on them). From
Felipe Contreras.
8) Assorted ACPI fixes and cleanups from Aaron Lu, Hanjun Guo,
Kuppuswamy Sathyanarayanan, Lan Tianyu, Sachin Kamat, Tang Chen,
Toshi Kani, and Wei Yongjun.
9) cpufreq ondemand governor target frequency selection change to
reduce oscillations between min and max frequencies (essentially,
it causes the governor to choose target frequencies proportional
to load) from Stratos Karafotis.
10) cpufreq fixes allowing sysfs attributes file permissions to be
preserved over suspend/resume cycles Srivatsa S Bhat.
11) Removal of Device Tree parsing for CPU device nodes from multiple
cpufreq drivers that required some changes related to
of_get_cpu_node() to be made in a few architectures and in the
driver core. From Sudeep KarkadaNagesha.
12) cpufreq core fixes and cleanups related to mutual exclusion and
driver module references from Viresh Kumar, Lukasz Majewski and
Rafael J Wysocki.
13) Assorted cpufreq fixes and cleanups from Amit Daniel Kachhap,
Bartlomiej Zolnierkiewicz, Hanjun Guo, Jingoo Han, Joseph Lo,
Julia Lawall, Li Zhong, Mark Brown, Sascha Hauer, Stephen Boyd,
Stratos Karafotis, and Viresh Kumar.
14) Fixes to prevent race conditions in coupled cpuidle from happening
from Colin Cross.
15) cpuidle core fixes and cleanups from Daniel Lezcano and
Tuukka Tikkanen.
16) Assorted cpuidle fixes and cleanups from Daniel Lezcano,
Geert Uytterhoeven, Jingoo Han, Julia Lawall, Linus Walleij,
and Sahara.
17) System sleep tracing changes from Todd E Brandt and Shuah Khan.
18) PNP subsystem conversion to using struct dev_pm_ops for power
management from Shuah Khan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABCAAGBQJSJcKhAAoJEKhOf7ml8uNsplIQAJSOshxhkkemvFOuHZ+0YIbh
R9aufjXeDkMDBi8YtU+tB7ERth1j+0LUSM0NTnP51U7e+7eSGobA9s5jSZQj2l7r
HFtnSOegLuKAfqwgfSLK91xa1rTFdfW0Kych9G2nuHtBIt6P0Oc59Cb5M0oy6QXs
nVtaDEuU//tmO71+EF5HnMJHabRTrpvtn/7NbDUpU7LZYpWJrHJFT9xt1rXNab7H
YRCATPm3kXGRg58Doc3EZE4G3D7DLvq74jWMaI089X/m5Pg1G6upqArypOy6oxdP
p2FEzYVrb2bi8fakXp7BBeO1gCJTAqIgAkbSSZHLpGhFaeEMmb9/DWPXdm2TjzMV
c1EEucvsqZWoprXgy12i5Hk814xN8d8nBBLg/UYiRJ44nc/hevXfyE9ZYj6bkseJ
+GNHmZIa1QYC05nnGli4+W4kHns8EZf/gmvIxnPuco1RN2yMWagrud5/G6Dr9M2B
hzJV6qauLVzgZso4oe79zv9aVxe/dPHKANLD/sg23WBiJJbJF1ocBlnj2Xlbpqze
pmMUWGiO/gUiS0fmpW/lAJauza5jFmSCjE4E8R0Gyn0j4YXjmMhdEanaU6J3VuCi
yVgEzYEth4sowq4AflMMLKYN+WmozDnK7taZRGmT0t+EKRFKLT6EgnNrkQgs1vKl
oawD9LM4fZ8E0yroOEme
=CgqW
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
1) ACPI-based PCI hotplug (ACPIPHP) subsystem rework and introduction
of Intel Thunderbolt support on systems that use ACPI for signalling
Thunderbolt hotplug events. This also should make ACPIPHP work in
some cases in which it was known to have problems. From
Rafael J Wysocki, Mika Westerberg and Kirill A Shutemov.
2) ACPI core code cleanups and dock station support cleanups from
Jiang Liu and Rafael J Wysocki.
3) Fixes for locking problems related to ACPI device hotplug from
Rafael J Wysocki.
4) ACPICA update to version 20130725 includig fixes, cleanups, support
for more than 256 GPEs per GPE block and a change to make the ACPI
PM Timer optional (we've seen systems without the PM Timer in the
field already). One of the fixes, related to the DeRefOf operator,
is necessary to prevent some Windows 8 oriented AML from causing
problems to happen. From Bob Moore, Lv Zheng, and Jung-uk Kim.
5) Removal of the old and long deprecated /proc/acpi/event interface
and related driver changes from Thomas Renninger.
6) ACPI and Xen changes to make the reduced hardware sleep work with
the latter from Ben Guthro.
7) ACPI video driver cleanups and a blacklist of systems that should
not tell the BIOS that they are compatible with Windows 8 (or ACPI
backlight and possibly other things will not work on them). From
Felipe Contreras.
8) Assorted ACPI fixes and cleanups from Aaron Lu, Hanjun Guo,
Kuppuswamy Sathyanarayanan, Lan Tianyu, Sachin Kamat, Tang Chen,
Toshi Kani, and Wei Yongjun.
9) cpufreq ondemand governor target frequency selection change to
reduce oscillations between min and max frequencies (essentially,
it causes the governor to choose target frequencies proportional
to load) from Stratos Karafotis.
10) cpufreq fixes allowing sysfs attributes file permissions to be
preserved over suspend/resume cycles Srivatsa S Bhat.
11) Removal of Device Tree parsing for CPU device nodes from multiple
cpufreq drivers that required some changes related to
of_get_cpu_node() to be made in a few architectures and in the
driver core. From Sudeep KarkadaNagesha.
12) cpufreq core fixes and cleanups related to mutual exclusion and
driver module references from Viresh Kumar, Lukasz Majewski and
Rafael J Wysocki.
13) Assorted cpufreq fixes and cleanups from Amit Daniel Kachhap,
Bartlomiej Zolnierkiewicz, Hanjun Guo, Jingoo Han, Joseph Lo,
Julia Lawall, Li Zhong, Mark Brown, Sascha Hauer, Stephen Boyd,
Stratos Karafotis, and Viresh Kumar.
14) Fixes to prevent race conditions in coupled cpuidle from happening
from Colin Cross.
15) cpuidle core fixes and cleanups from Daniel Lezcano and
Tuukka Tikkanen.
16) Assorted cpuidle fixes and cleanups from Daniel Lezcano,
Geert Uytterhoeven, Jingoo Han, Julia Lawall, Linus Walleij,
and Sahara.
17) System sleep tracing changes from Todd E Brandt and Shuah Khan.
18) PNP subsystem conversion to using struct dev_pm_ops for power
management from Shuah Khan.
* tag 'pm+acpi-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (217 commits)
cpufreq: Don't use smp_processor_id() in preemptible context
cpuidle: coupled: fix race condition between pokes and safe state
cpuidle: coupled: abort idle if pokes are pending
cpuidle: coupled: disable interrupts after entering safe state
ACPI / hotplug: Remove containers synchronously
driver core / ACPI: Avoid device hot remove locking issues
cpufreq: governor: Fix typos in comments
cpufreq: governors: Remove duplicate check of target freq in supported range
cpufreq: Fix timer/workqueue corruption due to double queueing
ACPI / EC: Add ASUSTEK L4R to quirk list in order to validate ECDT
ACPI / thermal: Add check of "_TZD" availability and evaluating result
cpufreq: imx6q: Fix clock enable balance
ACPI: blacklist win8 OSI for buggy laptops
cpufreq: tegra: fix the wrong clock name
cpuidle: Change struct menu_device field types
cpuidle: Add a comment warning about possible overflow
cpuidle: Fix variable domains in get_typical_interval()
cpuidle: Fix menu_device->intervals type
cpuidle: CodingStyle: Break up multiple assignments on single line
cpuidle: Check called function parameter in get_typical_interval()
...
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
via-rng currently isn't auto-loaded if built as a module.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Randy reports:
x86_64:
drivers/built-in.o: In function `xen_tpmfront_init':
xen-tpmfront.c:(.init.text+0x257c): undefined reference to `xenbus_register_frontend'
This is nicely fixed by selecting the XenBus frontend module.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The newly added omap4 support in the driver was added without
consideration for building older configs. When building omap1_defconfig,
it resulted in:
drivers/char/hw_random/omap-rng.c:190:12: warning: 'omap4_rng_init' defined but not used [-Wunused-function]
drivers/char/hw_random/omap-rng.c:215:13: warning: 'omap4_rng_cleanup' defined but not used [-Wunused-function]
drivers/char/hw_random/omap-rng.c:251:20: warning: 'omap4_rng_irq' defined but not used [-Wunused-function]
Move the code around so it is grouped with its operations struct, which
for the omap4 case means also under the #ifdef CONFIG_OF, where it needs
to be.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is a complete rewrite of the Xen TPM frontend driver, taking
advantage of a simplified frontend/backend interface and adding support
for cancellation and timeouts. The backend for this driver is provided
by a vTPM stub domain using the interface in Xen 4.3.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Acked-by: Matthew Fioravante <matthew.fioravante@jhuapl.edu>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
'rng_dev' is used only in this file.
Fix the following sparse warning:
drivers/char/hw_random/picoxcell-rng.c:36:15: warning: symbol 'rng_dev' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for OMAP4 version of TRNG module
that is present on OMAP4, AM33xx and OMAP5 SoCs.
The modules have several differences including register
offsets, output size, triggering rng and how configuring
FROs. To handle these differences, a platform_data structure
is defined and contains routine pointers, register offsets. OMAP2
specific routines are prefixed with 'omap2_' and OMAP4
specific routines are prefixed with 'omap4_'.
Note: Few Hard coded values are from the TI AM33xx SDK.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add Device Tree suport to the omap-rng driver.
Currently, only support for OMAP2 and OMAP3 is
being added but support for OMAP4 and OMAP5 will
be added in a subsequent patch.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
platform_set_drvdata() is called twice in driver probe.
Removing the duplicated call.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_kzalloc() to make cleanup paths simpler.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
module_platform_driver() makes the code simpler.
Using the macro in the driver.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the debugfs path before freeing port->name, to prevent a possible
use-after-free.
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The next commit gets conflicts because it relies on patches which were
cc:stable and thus had to be merged into Linus' tree before the coming
merge window. So pull in master now.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
and all CC:stable..
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ZV9B
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"More virtio console fixes than I'm happy with, but all real issues,
and all CC:stable.."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-scsi: Fix virtqueue affinity setup
virtio: console: return -ENODEV on all read operations after unplug
virtio: console: fix raising SIGIO after port unplug
virtio: console: clean up port data immediately at time of unplug
virtio: console: fix race in port_fops_open() and port unplug
virtio: console: fix race with port unplug and open/close
virtio/console: Add pipe_lock/unlock for splice_write
virtio/console: Quit from splice_write if pipe->nrbufs is 0
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Allow binding of user memory to the AGP GART on systems with HP
Quicksilver AGP bus. This resolves 'bind memory failed' error seen in
dmesg:
[29.365973] [TTM] AGP Bind memory failed.
…
[29.367030] [drm] Forcing AGP to PCI mode
The system doesn't more fail to bind the memory, and hence not falling
back to the PCI mode (if other failures aren't detected).
This is just a simple write down from the following patches:
agp/amd-k7: Allow binding user memory to the AGP GART
agp/hp-agp: Allow binding user memory to the AGP GART
Signed-off-by: Alex Ivanov <gnidorah@p0n4ik.tk>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Helge Deller <deller@gmx.de>
The PTR_ERR(NULL) here is not useful.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
send_sigio_to_port() checks the value of guest_connected, which we
always modify under the inbuf_lock; make sure invocations of
send_sigio_to_port() have take the inbuf_lock around the call.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Port unplug can race with close() in port_fops_release().
port_fops_release() already takes the necessary locks, ensure
unplug_port() does that too.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The removal functions act on the vqs, and the vq operations need to be
locked.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If a port gets unplugged while a user is blocked on read(), -ENODEV is
returned. However, subsequent read()s returned 0, indicating there's no
host-side connection (but not indicating the device went away).
This also happened when a port was unplugged and the user didn't have
any blocking operation pending. If the user didn't monitor the SIGIO
signal, they won't have a chance to find out if the port went away.
Fix by returning -ENODEV on all read()s after the port gets unplugged.
write() already behaves this way.
CC: <stable@vger.kernel.org>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
SIGIO should be sent when a port gets unplugged. It should only be sent
to prcesses that have the port opened, and have asked for SIGIO to be
delivered. We were clearing out guest_connected before calling
send_sigio_to_port(), resulting in a sigio not getting sent to
processes.
Fix by setting guest_connected to false after invoking the sigio
function.
CC: <stable@vger.kernel.org>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We used to keep the port's char device structs and the /sys entries
around till the last reference to the port was dropped. This is
actually unnecessary, and resulted in buggy behaviour:
1. Open port in guest
2. Hot-unplug port
3. Hot-plug a port with the same 'name' property as the unplugged one
This resulted in hot-plug being unsuccessful, as a port with the same
name already exists (even though it was unplugged).
This behaviour resulted in a warning message like this one:
-------------------8<---------------------------------------
WARNING: at fs/sysfs/dir.c:512 sysfs_add_one+0xc9/0x130() (Not tainted)
Hardware name: KVM
sysfs: cannot create duplicate filename
'/devices/pci0000:00/0000:00:04.0/virtio0/virtio-ports/vport0p1'
Call Trace:
[<ffffffff8106b607>] ? warn_slowpath_common+0x87/0xc0
[<ffffffff8106b6f6>] ? warn_slowpath_fmt+0x46/0x50
[<ffffffff811f2319>] ? sysfs_add_one+0xc9/0x130
[<ffffffff811f23e8>] ? create_dir+0x68/0xb0
[<ffffffff811f2469>] ? sysfs_create_dir+0x39/0x50
[<ffffffff81273129>] ? kobject_add_internal+0xb9/0x260
[<ffffffff812733d8>] ? kobject_add_varg+0x38/0x60
[<ffffffff812734b4>] ? kobject_add+0x44/0x70
[<ffffffff81349de4>] ? get_device_parent+0xf4/0x1d0
[<ffffffff8134b389>] ? device_add+0xc9/0x650
-------------------8<---------------------------------------
Instead of relying on guest applications to release all references to
the ports, we should go ahead and unregister the port from all the core
layers. Any open/read calls on the port will then just return errors,
and an unplug/plug operation on the host will succeed as expected.
This also caused buggy behaviour in case of the device removal (not just
a port): when the device was removed (which means all ports on that
device are removed automatically as well), the ports with active
users would clean up only when the last references were dropped -- and
it would be too late then to be referencing char device pointers,
resulting in oopses:
-------------------8<---------------------------------------
PID: 6162 TASK: ffff8801147ad500 CPU: 0 COMMAND: "cat"
#0 [ffff88011b9d5a90] machine_kexec at ffffffff8103232b
#1 [ffff88011b9d5af0] crash_kexec at ffffffff810b9322
#2 [ffff88011b9d5bc0] oops_end at ffffffff814f4a50
#3 [ffff88011b9d5bf0] die at ffffffff8100f26b
#4 [ffff88011b9d5c20] do_general_protection at ffffffff814f45e2
#5 [ffff88011b9d5c50] general_protection at ffffffff814f3db5
[exception RIP: strlen+2]
RIP: ffffffff81272ae2 RSP: ffff88011b9d5d00 RFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880118901c18 RCX: 0000000000000000
RDX: ffff88011799982c RSI: 00000000000000d0 RDI: 3a303030302f3030
RBP: ffff88011b9d5d38 R8: 0000000000000006 R9: ffffffffa0134500
R10: 0000000000001000 R11: 0000000000001000 R12: ffff880117a1cc10
R13: 00000000000000d0 R14: 0000000000000017 R15: ffffffff81aff700
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#6 [ffff88011b9d5d00] kobject_get_path at ffffffff8126dc5d
#7 [ffff88011b9d5d40] kobject_uevent_env at ffffffff8126e551
#8 [ffff88011b9d5dd0] kobject_uevent at ffffffff8126e9eb
#9 [ffff88011b9d5de0] device_del at ffffffff813440c7
-------------------8<---------------------------------------
So clean up when we have all the context, and all that's left to do when
the references to the port have dropped is to free up the port struct
itself.
CC: <stable@vger.kernel.org>
Reported-by: chayang <chayang@redhat.com>
Reported-by: YOGANANTH SUBRAMANIAN <anantyog@in.ibm.com>
Reported-by: FuXiangChun <xfu@redhat.com>
Reported-by: Qunfang Zhang <qzhang@redhat.com>
Reported-by: Sibiao Luo <sluo@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Between open() being called and processed, the port can be unplugged.
Check if this happened, and bail out.
A simple test script to reproduce this is:
while true; do for i in $(seq 1 100); do echo $i > /dev/vport0p3; done; done;
This opens and closes the port a lot of times; unplugging the port while
this is happening triggers the bug.
CC: <stable@vger.kernel.org>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
There's a window between find_port_by_devt() returning a port and us
taking a kref on the port, where the port could get unplugged. Fix it
by taking the reference in find_port_by_devt() itself.
Problem reported and analyzed by Mateusz Guzik.
CC: <stable@vger.kernel.org>
Reported-by: Mateusz Guzik <mguzik@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Suggested by coccinelle and manually verified.
Signed-off-by: Alexandru Juncu <alexj@rosedu.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the build error:
drivers/char/tile-srom.c:307:2: warning: missing braces around initializer [-Wmissing-braces]
and the resulting fallout for the missing '*' character, sorry, my
fault...
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the tile srom_class code to use
the correct field.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the bsr bsr_class code to use
the correct field.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quit from splice_write if pipe->nrbufs is 0 for avoiding oops in virtio-serial.
When an application was doing splice from a kernel buffer to virtio-serial on
a guest, the application received signal(SIGINT). This situation will normally
happen, but the kernel executed a kernel panic by oops as follows:
BUG: unable to handle kernel paging request at ffff882071c8ef28
IP: [<ffffffff812de48f>] sg_init_table+0x2f/0x50
PGD 1fac067 PUD 0
Oops: 0000 [#1] SMP
Modules linked in: lockd sunrpc bnep bluetooth rfkill ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_page_alloc snd_timer snd microcode virtio_balloon virtio_net pcspkr soundcore i2c_piix4 i2c_core uinput floppy
CPU: 1 PID: 908 Comm: trace-cmd Not tainted 3.10.0+ #49
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
task: ffff880071c64650 ti: ffff88007bf24000 task.ti: ffff88007bf24000
RIP: 0010:[<ffffffff812de48f>] [<ffffffff812de48f>] sg_init_table+0x2f/0x50
RSP: 0018:ffff88007bf25dd8 EFLAGS: 00010286
RAX: 0000001fffffffe0 RBX: ffff882071c8ef28 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff880071c8ef48
RBP: ffff88007bf25de8 R08: ffff88007fd15d40 R09: ffff880071c8ef48
R10: ffffea0001c71040 R11: ffffffff8139c555 R12: 0000000000000000
R13: ffff88007506a3c0 R14: ffff88007c862500 R15: ffff880071c8ef00
FS: 00007f0a3646c740(0000) GS:ffff88007fd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff882071c8ef28 CR3: 000000007acbb000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff880071c8ef48 ffff88007bf25e20 ffff88007bf25e88 ffffffff8139d6fa
ffff88007bf25e28 ffffffff8127a3f4 0000000000000000 0000000000000000
ffff880071c8ef48 0000100000000000 0000000000000003 ffff88007bf25e08
Call Trace:
[<ffffffff8139d6fa>] port_fops_splice_write+0xaa/0x130
[<ffffffff8127a3f4>] ? selinux_file_permission+0xc4/0x120
[<ffffffff8139d650>] ? wait_port_writable+0x1b0/0x1b0
[<ffffffff811a6fe0>] do_splice_from+0xa0/0x110
[<ffffffff811a951f>] SyS_splice+0x5ff/0x6b0
[<ffffffff8161f8c2>] system_call_fastpath+0x16/0x1b
Code: c1 e2 05 48 89 e5 48 83 ec 10 4c 89 65 f8 41 89 f4 31 f6 48 89 5d f0 48 89 fb e8 8d ce ff ff 41 8d 44 24 ff 48 c1 e0 05 48 01 c3 <48> 8b 03 48 83 e0 fe 48 83 c8 02 48 89 03 48 8b 5d f0 4c 8b 65
RIP [<ffffffff812de48f>] sg_init_table+0x2f/0x50
RSP <ffff88007bf25dd8>
CR2: ffff882071c8ef28
---[ end trace 86323505eb42ea8f ]---
It seems to induce pagefault in sg_init_tabel() when pipe->nrbufs is equal to
zero. This may happen in a following situation:
(1) The application normally does splice(read) from a kernel buffer, then does
splice(write) to virtio-serial.
(2) The application receives SIGINT when is doing splice(read), so splice(read)
is failed by EINTR. However, the application does not finish the operation.
(3) The application tries to do splice(write) without pipe->nrbufs.
(4) The virtio-console driver tries to touch scatterlist structure sgl in
sg_init_table(), but the region is out of bound.
To avoid the case, a kernel should check whether pipe->nrbufs is empty or not
when splice_write is executed in the virtio-console driver.
V3: Add Reviewed-by lines and stable@ line in sign-off area.
Signed-off-by: Yoshihiro YUNOMAE <yoshihiro.yunomae.ez@hitachi.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It is quite some time that this one has been deprecated.
Get rid of it.
Should some really important user be overseen, it may be reverted and
the userspace program worked on first, but it is time to do something
to get rid of this old stuff...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
Smatch complains that on 64 bit systems, there is a hole in the
MW_ABILITIES struct between ->component_count and ->component_list[].
It leaks stack information from the mwave_ioctl() function.
I've added a memset() to initialize the struct to zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
PCI device hotplug
- Add pci_alloc_dev() interface (Gu Zheng)
- Add pci_bus_get()/put() for reference counting (Jiang Liu)
- Fix SR-IOV reference count issues (Jiang Liu)
- Remove unused acpi_pci_roots list (Jiang Liu)
MSI
- Conserve interrupt resources on x86 (Alexander Gordeev)
AER
- Force fatal severity when component has been reset (Betty Dall)
- Reset link below Root Port as well as Downstream Port (Betty Dall)
- Fix "Firmware first" flag setting (Bjorn Helgaas)
- Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
ASPM
- Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
Miscellaneous
- Add CircuitCo PCI IDs (Darren Hart)
- Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
- Work around Ivytown NTB BAR size issue (Jon Mason)
- Detect invalid initial BAR values (Kevin Hao)
- Add pcibios_release_device() (Sebastian Ott)
- Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=X3Lo
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"PCI device hotplug
- Add pci_alloc_dev() interface (Gu Zheng)
- Add pci_bus_get()/put() for reference counting (Jiang Liu)
- Fix SR-IOV reference count issues (Jiang Liu)
- Remove unused acpi_pci_roots list (Jiang Liu)
MSI
- Conserve interrupt resources on x86 (Alexander Gordeev)
AER
- Force fatal severity when component has been reset (Betty Dall)
- Reset link below Root Port as well as Downstream Port (Betty Dall)
- Fix "Firmware first" flag setting (Bjorn Helgaas)
- Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
ASPM
- Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
Miscellaneous
- Add CircuitCo PCI IDs (Darren Hart)
- Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
- Work around Ivytown NTB BAR size issue (Jon Mason)
- Detect invalid initial BAR values (Kevin Hao)
- Add pcibios_release_device() (Sebastian Ott)
- Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)"
* tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
MAINTAINERS: Add ACPI folks for ACPI-related things under drivers/pci
PCI: Add CircuitCo vendor ID and subsystem ID
PCI: Use pdev->pm_cap instead of pci_find_capability(..,PCI_CAP_ID_PM)
PCI: Return early on allocation failures to unindent mainline code
PCI: Simplify IOV implementation and fix reference count races
PCI: Drop redundant setting of bus->is_added in virtfn_add_bus()
unicore32/PCI: Remove redundant call of pci_bus_add_devices()
m68k/PCI: Remove redundant call of pci_bus_add_devices()
PCI / ACPI / PM: Use correct power state strings in messages
PCI: Fix comment typo for pcie_pme_remove()
PCI: Rename pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
PCI: Fix refcount issue in pci_create_root_bus() error recovery path
ia64/PCI: Clean up pci_scan_root_bus() usage
PCI/AER: Reset link for devices below Root Port or Downstream Port
ACPI / APEI: Force fatal AER severity when component has been reset
PCI/AER: Remove "extern" from function declarations
PCI/AER: Move AER severity defines to aer.h
PCI/AER: Set dev->__aer_firmware_first only for matching devices
PCI/AER: Factor out HEST device type matching
PCI/AER: Don't parse HEST table for non-PCIe devices
...
/dev/oldmem provides the interface for us to access the "old memory" in
the dump-capture kernel. Unfortunately, no one actually uses this
interface.
And this interface could actually cause some real problems if used on ia64
where the cached/uncached accesses are mixed. See the discussion from the
link: https://lkml.org/lkml/2013/4/12/386.
So Eric suggested that we should remove /dev/oldmem as an unused piece of
code.
[akpm@linux-foundation.org: mention /dev/oldmem obsolescence in devices.txt]
Suggested-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull security subsystem updates from James Morris:
"In this update, Smack learns to love IPv6 and to mount a filesystem
with a transmutable hierarchy (i.e. security labels are inherited
from parent directory upon creation rather than creating process).
The rest of the changes are maintenance"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (37 commits)
tpm/tpm_i2c_infineon: Remove unused header file
tpm: tpm_i2c_infinion: Don't modify i2c_client->driver
evm: audit integrity metadata failures
integrity: move integrity_audit_msg()
evm: calculate HMAC after initializing posix acl on tmpfs
maintainers: add Dmitry Kasatkin
Smack: Fix the bug smackcipso can't set CIPSO correctly
Smack: Fix possible NULL pointer dereference at smk_netlbl_mls()
Smack: Add smkfstransmute mount option
Smack: Improve access check performance
Smack: Local IPv6 port based controls
tpm: fix regression caused by section type conflict of tpm_dev_release() in ppc builds
maintainers: Remove Kent from maintainers
tpm: move TPM_DIGEST_SIZE defintion
tpm_tis: missing platform_driver_unregister() on error in init_tis()
security: clarify cap_inode_getsecctx description
apparmor: no need to delay vfree()
apparmor: fix fully qualified name parsing
apparmor: fix setprocattr arg processing for onexec
apparmor: localize getting the security context to a few macros
...
Pull second set of VFS changes from Al Viro:
"Assorted f_pos race fixes, making do_splice_direct() safe to call with
i_mutex on parent, O_TMPFILE support, Jeff's locks.c series,
->d_hash/->d_compare calling conventions changes from Linus, misc
stuff all over the place."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
Document ->tmpfile()
ext4: ->tmpfile() support
vfs: export lseek_execute() to modules
lseek_execute() doesn't need an inode passed to it
block_dev: switch to fixed_size_llseek()
cpqphp_sysfs: switch to fixed_size_llseek()
tile-srom: switch to fixed_size_llseek()
proc_powerpc: switch to fixed_size_llseek()
ubi/cdev: switch to fixed_size_llseek()
pci/proc: switch to fixed_size_llseek()
isapnp: switch to fixed_size_llseek()
lpfc: switch to fixed_size_llseek()
locks: give the blocked_hash its own spinlock
locks: add a new "lm_owner_key" lock operation
locks: turn the blocked_list into a hashtable
locks: convert fl_link to a hlist_node
locks: avoid taking global lock if possible when waking up blocked waiters
locks: protect most of the file_lock handling with i_lock
locks: encapsulate the fl_link list handling
locks: make "added" in __posix_lock_file a bool
...
These are various bug fixes that were not considered important enough
for merging into 3.10. The majority of the ARM fixes are for the OMAP
and at91 platforms, and there is another set of bug fixes for device
drivers that resolve 'randconfig' build errors and that the subsystem
maintainers either did not pick up or preferred to get merged through
the arm-soc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gNDf
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-cricitical bug fixes from Arnd Bergmann:
"These are various bug fixes that were not considered important enough
for merging into 3.10.
The majority of the ARM fixes are for the OMAP and at91 platforms, and
there is another set of bug fixes for device drivers that resolve
'randconfig' build errors and that the subsystem maintainers either
did not pick up or preferred to get merged through the arm-soc tree."
* tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: at91/PMC: use at91_usb_rate() for UTMI PLL
ARM: at91/PMC: fix at91sam9n12 USB FS init
ARM: at91/PMC: at91sam9n12 family has a PLLB
ARM: at91/PMC: sama5d3 family doesn't have a PLLB
ARM: tegra: fix section mismatch in tegra_pmc_parse_dt
ARM: mxs: don't select HAVE_PWM
ARM: mxs: stub out mxs_pm_init for !CONFIG_PM
cpuidle: calxeda: select ARM_CPU_SUSPEND
ARM: mvebu: fix length of ethernet registers in mv78260 dtsi
ARM: at91: cpuidle: Fix target_residency
ARM: at91: fix at91_extern_irq usage for non-dt boards
ARM: sirf: use CONFIG_SIRF rather than CONFIG_PRIMA2 where necessary
clocksource: kona: adapt to CLOCKSOURCE_OF_DECLARE change
X.509: do not emit any informational output
mtd: omap2: allow bulding as a module
[SCSI] nsp32: use mdelay instead of large udelay constants
hwrng: bcm2835: fix MODULE_LICENSE tag
ARM: at91: Change the internal SRAM memory type MT_MEMORY_NONCACHED
ARM: at91: Fix link breakage when !CONFIG_PHYLIB
MAINTAINERS: Add exynos filename match to ARM/S5P EXYNOS ARM ARCHITECTURES
...
Here's the big driver core merge for 3.11-rc1
Lots of little things, and larger firmware subsystem updates, all
described in the shortlog. Nice thing here is that we finally get rid
of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
been always on for a number of kernel releases, now it's just removed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRsGMACgkQMUfUDdst+ylIIACfW8lLxOPVK+iYG699TWEBAkp0
LFEAnjlpAMJ1JnoZCuWDZObNCev93zGB
=020+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the big driver core merge for 3.11-rc1
Lots of little things, and larger firmware subsystem updates, all
described in the shortlog. Nice thing here is that we finally get rid
of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
been always on for a number of kernel releases, now it's just
removed)"
* tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
driver core: device.h: fix doc compilation warnings
firmware loader: fix another compile warning with PM_SLEEP unset
build some drivers only when compile-testing
firmware loader: fix compile warning with PM_SLEEP set
kobject: sanitize argument for format string
sysfs_notify is only possible on file attributes
firmware loader: simplify holding module for request_firmware
firmware loader: don't export cache_firmware and uncache_firmware
drivers/base: Use attribute groups to create sysfs memory files
firmware loader: fix compile warning
firmware loader: fix build failure with !CONFIG_FW_LOADER_USER_HELPER
Documentation: Updated broken link in HOWTO
Finally eradicate CONFIG_HOTPLUG
driver core: firmware loader: kill FW_ACTION_NOHOTPLUG requests before suspend
driver core: firmware loader: don't cache FW_ACTION_NOHOTPLUG firmware
Documentation: Tidy up some drivers/base/core.c kerneldoc content.
platform_device: use a macro instead of platform_driver_register
firmware: move EXPORT_SYMBOL annotations
firmware: Avoid deadlock of usermodehelper lock at shutdown
dell_rbu: Select CONFIG_FW_LOADER_USER_HELPER explicitly
...
Here's the big char/misc driver tree merge for 3.11-rc1
A variety of different driver patches here. All of these have been in
linux-next for a while, and the networking patches were acked-by David
Miller, as it made sense for those patches to come through this tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRqsQACgkQMUfUDdst+ykNlACgwnDHLav/u2NrAxoqxmw7Bcd8
qY0An3h0ZGI5PpDe6U0IyBDQIipHuOjG
=vaRG
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here's the big char/misc driver tree merge for 3.11-rc1
A variety of different driver patches here. All of these have been in
linux-next for a while, and the networking patches were acked-by David
Miller, as it made sense for those patches to come through this tree"
* tag 'char-misc-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (102 commits)
Revert "char: misc: assign file->private_data in all cases"
drivers: uio_pdrv_genirq: Use of_match_ptr() macro
mei: check whether hw start has succeeded
mei: check if the hardware reset succeeded
mei: mei_cl_connect: don't multiply the timeout twice
mei: do not override a client writing state when buffering
mei: move mei_cl_irq_write_complete to client.c
UIO: Fix concurrency issue
drivers: uio_dmem_genirq: Use of_match_ptr() macro
char: misc: assign file->private_data in all cases
drivers: hv: allocate synic structures before hv_synic_init()
drivers: hv: check interrupt mask before read_index
vme: vme_tsi148.c: fix error return code in tsi148_probe()
FMC: fix error handling in probe() function
fmc: avoid readl/writel namespace conflict
FMC: NULL dereference on allocation failure
UIO: fix uio_pdrv_genirq with device tree but no interrupt
UIO: allow binding uio_pdrv_genirq.c to devices using command line option
FMC: add a char-device mezzanine driver
FMC: add a driver to write mezzanine EEPROM
...
This driver does not use any module parameters anymore,
so the inclusion of the header file can be removed.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The I2C client driver is not supposed to modify the client's driver pointer,
this is handled by the I2C core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEbBAABAgAGBQJRxf9cAAoJEHm+PkMAQRiGMWkH911xM4gRmFgE7SqVW4F4AWBm
ngcqMqNy9IdqKfibORUUDvVfEa5gjD5ai2quIKpfQiaukbpQJ696H90ijuAkajLn
DQBrN243s0pzhhc/quWINnWxsFQ613JjdUMUMaD7e9A1aKjYzWrPGt/tSjrFXGCP
tArTupVzc/iOmnEQDKiROI/Nokq44QJ36aTGPM7n08xMtpKmkCXM+9/UosBteB0O
HVI33dmjwz7i55fI53XAWyuZCE+gSEnA4z8spJ9LfXso2W14V+roc+GuL6OyeeTI
pCn/+4niVPb4B0ROZlpyVmdZjbPPcMMEK5o+BSJI68SH6LHZTQh2iVuqYfpSyA==
=uUH5
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc7' into drm-next
Linux 3.10-rc7
The sdvo lvds fix in this -fixes pull
commit c3456fb3e4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jun 10 09:47:58 2013 +0200
drm/i915: prefer VBT modes for SVDO-LVDS over EDID
has a silent functional conflict with
commit 990256aec2
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri May 31 12:17:07 2013 +0000
drm: Add probed modes in probe order
in drm-next. W simply need to add the vbt modes before edid modes, i.e. the
other way round than now.
Conflicts:
drivers/gpu/drm/drm_prime.c
drivers/gpu/drm/i915/intel_sdvo.c
In fa1f68db6c ("drivers: misc: pass miscdevice pointer via file
private data"), the misc driver infrastructure was changed to assigned
file->private_data as a pointer to the 'struct miscdevice' that
corresponds to the device being opened.
However, this assignment was only done when the misc driver was
declaring a driver-specific ->open() operation in its
file_operations. This doesn't make sense, as the driver may not
necessarily have a custom ->open() operation, and might still be
interested in having file->private_data properly set for use in its
->read() and write() operations.
Therefore, we move the assignment of file->private_data outside of the
condition that tests whether a driver-specific ->open() operation was
defined.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MODULE_LICENSE macro invocation must use either "GPL" or "GPL v2",
but not "GPLv2" in order to be detected by the module loader.
This fixes the allmodconfig build error:
FATAL: modpost: GPL-incompatible module bcm2835-rng.ko uses GPL-only symbol 'platform_driver_unregister'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Dom Cobley <popcornmix@gmail.com>
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: linux-rpi-kernel@lists.infradead.org
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The MODULE_LICENSE macro invocation must use either "GPL" or "GPL v2",
but not "GPLv2" in order to be detected by the module loader.
This fixes the allmodconfig build error:
FATAL: modpost: GPL-incompatible module bcm2835-rng.ko uses GPL-only symbol 'platform_driver_unregister'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Dom Cobley <popcornmix@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: Herbert Xu <herbert@gondor.apana.org.au>
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use IS_ERR_VALUE() instead of comparing the new offset to a hard-coded
value of -MAX_ERRNO (which is also off-by-one due to the use of ~
instead of -).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new pci_alloc_dev(bus) to replace the existing using of
alloc_pci_dev(void).
[bhelgaas: drop pci_bus ref later in pci_release_dev()]
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
The Nomadik HW RNG driver has seen some rust and is not preparing
the clock before use. Fix this up so we get rid of runtime
complaints from the clock subsystem.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Support for the Stallion multiport serial drivers was removed in v3.1.
Clean up their last references in the tree: mainly an outdated Kconfig
entry and unneeded documentation.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ever since commit 45f035ab9b ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off. Remove all the remaining references to it.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I'm not sure I understand the intent of the previous behavior. mmap
on /dev/agpgart and DRM_AGP maps had no cache flags set, so they
would be fully cacheable. But the DRM code (most of the time) would
add a write-combining MTRR that would change the effective memory
type to WC.
The new behavior just requests WC explicitly for all AGP maps.
If there is any code out there that expects cacheable access to the
AGP aperture (because the drm driver doesn't request an MTRR or
because it's using /dev/agpgart directly), then it will now end up
with a UC or WC mapping, depending on the architecture and PAT
availability. But cacheable access to the aperture seems like it's
asking for trouble, because, AIUI, the aperture is an alias of RAM.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
s/regsiter/register/
Use origin comment from the first driver version
which also explain the usage of XHI_MAX_RETRIES better.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8119807 commit reintroduced a regression
(error: __ksymtab_tpm_dev_release causes a section type conflict) that was fixed by commit
cbb2ed4.
Fix it for good by adding the prototype to tpm.h so sparse doesn't
complain about it anymore.
Reported-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Commit 902c098a36 ("random: use lockless techniques in the interrupt
path") turned IRQ path from being spinlock protected into lockless
cmpxchg-retry update.
That commit removed r->lock serialization between crediting entropy bits
from IRQ context and accounting when extracting entropy on userspace
read path, but didn't turn the r->entropy_count reads/updates in
account() to use cmpxchg as well.
It has been observed, that under certain circumstances this leads to
read() on /dev/urandom to return 0 (EOF), as r->entropy_count gets
corrupted and becomes negative, which in turn results in propagating 0
all the way from account() to the actual read() call.
Convert the accounting code to be the proper lockless counterpart of
what has been partially done by 902c098a36.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ec8f02da9e ("random: prime last_data value per fips
requirements") added priming of last_data per fips requirements.
Unfortuantely, it did so in a way that can lead to multiple threads all
incrementing nbytes, but only one actually doing anything with the extra
data, which leads to some fun random corruption and panics.
The fix is to simply do everything needed to prime last_data in a single
shot, so there's no window for multiple cpus to increment nbytes -- in
fact, we won't even increment or decrement nbytes anymore, we'll just
extract the needed EXTRACT_SIZE one time per pool and then carry on with
the normal routine.
All these changes have been tested across multiple hosts and
architectures where panics were previously encoutered. The code changes
are are strictly limited to areas only touched when when booted in fips
mode.
This change should also go into 3.8-stable, to make the myriads of fips
users on 3.8.x happy.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stodola <jstodola@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Here are some small char/misc driver fixes for 3.10-rc2.
Nothing major here, just a number of fixes for things that people have
reported, and a MAINTAINERS update for the recent changes for the hyperv
files that went into 3.10-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlGePEIACgkQMUfUDdst+yk0VQCfXuaBzq+dtK4k2aMtzNYl7KW3
8HsAoLxBNJAVg3iic8xs3HuHnIzwuL1W
=rkfh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are some small char/misc driver fixes for 3.10-rc2.
Nothing major here, just a number of fixes for things that people have
reported, and a MAINTAINERS update for the recent changes for the
hyperv files that went into 3.10-rc1."
* tag 'char-misc-3.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
ttyprintk: Fix NULL pointer deref by setting tty_port ops after initializing port
uio: UIO_DMEM_GENIRQ should depend on HAS_DMA
MAINTAINERS: update Hyper-V file list
mei: bus: Reset event_cb when disabling a device
Drivers: hv: Fix a bug in get_vp_index()
mei: fix out of array access to me clients array
Char: lp, protect LPGETSTATUS with port_mutex
dummy-irq: require the user to specify an IRQ number
IMA requires access to TPM_DIGEST_SIZE definition. This patch
moves the definition to <linux/tpm.h>.
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Add the missing platform_driver_unregister() before return
from init_tis() in the device register error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
tty_port_init() zeroes out the tty port, which means that we have to set the
ops pointer /after/, not before this call. Otherwise, tty_port_open will crash
when it tries to deref ops, which is now a NULL pointer.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(*->vm_end - *->vm_start) >> PAGE_SHIFT operation is implemented
as a inline funcion vma_pages() in linux/mm.h, so using it.
Signed-off-by: Libin <huawei.libin@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull devm usage cleanup from Wolfram Sang:
"Lately, I have been experimenting how to improve the devm interface to
make writing device drivers easier and less error prone while also
getting rid of its subtle issues. I think it has more potential but
still needs work and definately conistency, especiall in its usage.
The first thing I come up with is a low hanging fruit regarding
devm_ioremap_resouce(). This function already checks if the passed
resource is valid and gives an error message if not. So, we can
remove similar checks from the drivers and get rid of a bit of code
and a number of inconsistent error strings.
This series only removes the unneeded check iff devm_ioremap_resource
follows platform_get_resource directly. The previous version tried to
shuffle code if needed, too, what lead to an embarrasing bug. It
turned out to me that shuffling code for all cases found will make the
automated script too complex, so I am unsure if an automated cleanup
is the proper tool for this case. Removing the easy stuff seems
worthwhile to me, though.
Despite various architectures and platform dependencies, I managed to
compile test 45 out of 57 modified files locally using heuristics and
defconfigs."
Pulled because: 296 deletions, 0 additions.
* 'devm_no_resource_check' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (33 commits)
sound/soc/kirkwood: don't check resource with devm_ioremap_resource
sound/soc/fsl: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
arch/arm/plat-samsung: don't check resource with devm_ioremap_resource
arch/arm/mach-tegra: don't check resource with devm_ioremap_resource
drivers/watchdog: don't check resource with devm_ioremap_resource
drivers/w1/masters: don't check resource with devm_ioremap_resource
drivers/video/omap2/dss: don't check resource with devm_ioremap_resource
drivers/video/omap2: don't check resource with devm_ioremap_resource
drivers/usb/phy: don't check resource with devm_ioremap_resource
drivers/usb/host: don't check resource with devm_ioremap_resource
drivers/usb/gadget: don't check resource with devm_ioremap_resource
drivers/usb/chipidea: don't check resource with devm_ioremap_resource
drivers/thermal: don't check resource with devm_ioremap_resource
drivers/staging/nvec: don't check resource with devm_ioremap_resource
drivers/staging/dwc2: don't check resource with devm_ioremap_resource
drivers/spi: don't check resource with devm_ioremap_resource
drivers/rtc: don't check resource with devm_ioremap_resource
drivers/pwm: don't check resource with devm_ioremap_resource
drivers/pinctrl: don't check resource with devm_ioremap_resource
...
The patch fixes a problem in the lp driver that can cause oopses as
follows:
process A: calls lp_write, which in turn calls
parport_ieee1284_write_compat, and that invokes
parport_wait_peripheral
process B: meanwhile does an ioctl(LPGETSTATUS), which call
lp_release_parport when done. This function will set
physport->cad = NULL.
process A: parport_wait_peripheral tries to dereference
physport->cad and dies
So, protect that code with the port_mutex in order to protect against
simultaneous calls to lp_read/lp_write.
Similar protection is probably required for ioctl(LPRESET)...
This patch was done by IBM a while back and we (at suse) have that
since at least 2004 in our repos. Let's make it upstream.
Signed-off-by: okir@suse.de
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a 32 bit version of ipmitool is used on a 64 bit kernel, the
ipmi_devintf code fails to correctly acquire ipmi_mutex. This results in
incomplete data being retrieved in some cases, or other possible failures.
Add a wrapper around compat_ipmi_ioctl() to take ipmi_mutex to fix this.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the interrupt enable message returns an error, the messages are
not entirely accurate nor helpful. So improve them.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replaced calls to kmalloc followed by strcpy with a sincle call to
kstrdup. Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These are handy for measuring the cost of the aio infrastructure with
operations that do very little and complete immediately.
Signed-off-by: Zach Brown <zab@redhat.com>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull crypto update from Herbert Xu:
- XTS mode optimisation for twofish/cast6/camellia/aes on x86
- AVX2/x86_64 implementation for blowfish/twofish/serpent/camellia
- SSSE3/AVX/AVX2 optimisations for sha256/sha512
- Added driver for SAHARA2 crypto accelerator
- Fix for GMAC when used in non-IPsec secnarios
- Added generic CMAC implementation (including IPsec glue)
- IP update for crypto/atmel
- Support for more than one device in hwrng/timeriomem
- Added Broadcom BCM2835 RNG driver
- Misc fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (59 commits)
crypto: caam - fix job ring cleanup code
crypto: camellia - add AVX2/AES-NI/x86_64 assembler implementation of camellia cipher
crypto: serpent - add AVX2/x86_64 assembler implementation of serpent cipher
crypto: twofish - add AVX2/x86_64 assembler implementation of twofish cipher
crypto: blowfish - add AVX2/x86_64 implementation of blowfish cipher
crypto: tcrypt - add async cipher speed tests for blowfish
crypto: testmgr - extend camellia test-vectors for camellia-aesni/avx2
crypto: aesni_intel - fix Kconfig problem with CRYPTO_GLUE_HELPER_X86
crypto: aesni_intel - add more optimized XTS mode for x86-64
crypto: x86/camellia-aesni-avx - add more optimized XTS code
crypto: cast6-avx: use new optimized XTS code
crypto: x86/twofish-avx - use optimized XTS code
crypto: x86 - add more optimized XTS-mode for serpent-avx
xfrm: add rfc4494 AES-CMAC-96 support
crypto: add CMAC support to CryptoAPI
crypto: testmgr - add empty test vectors for null ciphers
crypto: testmgr - add AES GMAC test vectors
crypto: gcm - fix rfc4543 to handle async crypto correctly
crypto: gcm - make GMAC work when dst and src are different
hwrng: timeriomem - added devicetree hooks
...
I dived into lguest again, reworking the pagetable code so we can move
the switcher page: our fixmaps sometimes take more than 2MB now...
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRga7lAAoJENkgDmzRrbjx/yIQAKpqIBtxOJeYH3SY+Uoe7Cfp
toNYcpJEldvb0UcWN8M2cSZpHoxl1SUoq9djwcM29tcKa7EZAjHaGtb/Q1qMTDgv
+B3WAfiGU2pmXFxLAkbrlLNGnysy24JspqJQ5hcYV84EiBxQdZp+nCYgOphd+GMK
ww16vo9ya8jFjzt3GeRp/Heb3vEzV4Cp6BC3i0m8A3WNpEpbRb66pqXNk5o8ggJO
SxQOKSXmUM+0m+jKSul5xn3e2Ls2LOrZZ8/DIHA+gW66N4Zab7n2/j1Q9VRxb4lh
FqnR7KwgBX8OCh9IsBDqQYS7MohvMYge6eUdLtFrq84jvMleMEhrC8q9v2tucFUb
5t18CLwvyK7Gdg6UCKiZ7YSPcuURAILO16al9bh5IseeBDsuX+43VsvQoBmFn9k6
cLOVTZ6BlOmahK5PyRYFSvLa9Rxzr/05Mr7oYq9UgshD9io78dnqczFYIORF53rW
zD7C4HuTZfYJFfNd0wAJ0RfVXnf8QvDlMdo7zPC26DSXNWqj8OexCY0qqSWUB+2F
vcfJP6NkV4fZB8aawWIFUVwc64yqtt2uPVLa7ATZWqk16PgKrchGewmw3tiEwOgu
1l7xgffTRRUIJsqaCZoXdgw3yezcKRjuUBcOxL09lDAAhc+NxWNvzZBsKp66DwDk
yZQKn0OdXnuf0CeEOfFf
=1tYL
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio & lguest updates from Rusty Russell:
"Lots of virtio work which wasn't quite ready for last merge window.
Plus I dived into lguest again, reworking the pagetable code so we can
move the switcher page: our fixmaps sometimes take more than 2MB now..."
Ugh. Annoying conflicts with the tcm_vhost -> vhost_scsi rename.
Hopefully correctly resolved.
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (57 commits)
caif_virtio: Remove bouncing email addresses
lguest: improve code readability in lg_cpu_start.
virtio-net: fill only rx queues which are being used
lguest: map Switcher below fixmap.
lguest: cache last cpu we ran on.
lguest: map Switcher text whenever we allocate a new pagetable.
lguest: don't share Switcher PTE pages between guests.
lguest: expost switcher_pages array (as lg_switcher_pages).
lguest: extract shadow PTE walking / allocating.
lguest: make check_gpte et. al return bool.
lguest: assume Switcher text is a single page.
lguest: rename switcher_page to switcher_pages.
lguest: remove RESERVE_MEM constant.
lguest: check vaddr not pgd for Switcher protection.
lguest: prepare to make SWITCHER_ADDR a variable.
virtio: console: replace EMFILE with EBUSY for already-open port
virtio-scsi: reset virtqueue affinity when doing cpu hotplug
virtio-scsi: introduce multiqueue support
virtio-scsi: push vq lock/unlock into virtscsi_vq_done
virtio-scsi: pass struct virtio_scsi to virtqueue completion function
...
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Merge third batch of fixes from Andrew Morton:
"Most of the rest. I still have two large patchsets against AIO and
IPC, but they're a bit stuck behind other trees and I'm about to
vanish for six days.
- random fixlets
- inotify
- more of the MM queue
- show_stack() cleanups
- DMI update
- kthread/workqueue things
- compat cleanups
- epoll udpates
- binfmt updates
- nilfs2
- hfs
- hfsplus
- ptrace
- kmod
- coredump
- kexec
- rbtree
- pids
- pidns
- pps
- semaphore tweaks
- some w1 patches
- relay updates
- core Kconfig changes
- sysrq tweaks"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (109 commits)
Documentation/sysrq: fix inconstistent help message of sysrq key
ethernet/emac/sysrq: fix inconstistent help message of sysrq key
sparc/sysrq: fix inconstistent help message of sysrq key
powerpc/xmon/sysrq: fix inconstistent help message of sysrq key
ARM/etm/sysrq: fix inconstistent help message of sysrq key
power/sysrq: fix inconstistent help message of sysrq key
kgdb/sysrq: fix inconstistent help message of sysrq key
lib/decompress.c: fix initconst
notifier-error-inject: fix module names in Kconfig
kernel/sys.c: make prctl(PR_SET_MM) generally available
UAPI: remove empty Kbuild files
menuconfig: print more info for symbol without prompts
init/Kconfig: re-order CONFIG_EXPERT options to fix menuconfig display
kconfig menu: move Virtualization drivers near other virtualization options
Kconfig: consolidate CONFIG_DEBUG_STRICT_USER_COPY_CHECKS
relay: use macro PAGE_ALIGN instead of FIX_SIZE
kernel/relay.c: move FIX_SIZE macro into relay.c
kernel/relay.c: remove unused function argument actor
drivers/w1/slaves/w1_ds2760.c: fix the error handling in w1_ds2760_add_slave()
drivers/w1/slaves/w1_ds2781.c: fix the error handling in w1_ds2781_add_slave()
...
There are several places in kernel where modules unescapes input to convert
C-Style Escape Sequences into byte codes.
The patch provides generic implementation of such approach. Test cases are
also included into the patch.
[akpm@linux-foundation.org: clarify comment]
[akpm@linux-foundation.org: export get_random_int() to modules]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: William Hubbs <w.d.hubbs@gmail.com>
Cc: Chris Brannon <chris@the-brannons.com>
Cc: Kirk Reiser <kirk@braille.uwo.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull security subsystem update from James Morris:
"Just some minor updates across the subsystem"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
ima: eliminate passing d_name.name to process_measurement()
TPM: Retry SaveState command in suspend path
tpm/tpm_i2c_infineon: Add small comment about return value of __i2c_transfer
tpm/tpm_i2c_infineon.c: Add OF attributes type and name to the of_device_id table entries
tpm_i2c_stm_st33: Remove duplicate inclusion of header files
tpm: Add support for new Infineon I2C TPM (SLB 9645 TT 1.2 I2C)
char/tpm: Convert struct i2c_msg initialization to C99 format
drivers/char/tpm/tpm_ppi: use strlcpy instead of strncpy
tpm/tpm_i2c_stm_st33: formatting and white space changes
Smack: include magic.h in smackfs.c
selinux: make security_sb_clone_mnt_opts return an error on context mismatch
seccomp: allow BPF_XOR based ALU instructions.
Fix NULL pointer dereference in smack_inode_unlink() and smack_inode_rmdir()
Smack: add support for modification of existing rules
smack: SMACK_MAGIC to include/uapi/linux/magic.h
Smack: add missing support for transmute bit in smack_str_from_perm()
Smack: prevent revoke-subject from failing when unseen label is written to it
tomoyo: use DEFINE_SRCU() to define tomoyo_ss
tomoyo: use DEFINE_SRCU() to define tomoyo_ss
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Arnd Bergmann <arnd@arndb.de>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Arnd Bergmann <arnd@arndb.de>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Arnd Bergmann <arnd@arndb.de>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Here's the big char / misc driver update for 3.10-rc1
A number of various driver updates, the majority being new functionality
in the MEI driver subsystem (it's now a subsystem, it started out just a
single driver), extcon updates, memory updates, hyper-v updates, and a
bunch of other small stuff that doesn't fit in any other tree.
All of these have been in linux-next for a while
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+mtYACgkQMUfUDdst+ymFXQCfdLsD4Cxz+jkgW+tljh9i70XD
OFkAnRPMMhLS8/kddf02lLMYzYUFdy1U
=zaFJ
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver update from Greg Kroah-Hartman:
"Here's the big char / misc driver update for 3.10-rc1
A number of various driver updates, the majority being new
functionality in the MEI driver subsystem (it's now a subsystem, it
started out just a single driver), extcon updates, memory updates,
hyper-v updates, and a bunch of other small stuff that doesn't fit in
any other tree.
All of these have been in linux-next for a while"
* tag 'char-misc-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (148 commits)
Tools: hv: Fix a checkpatch warning
tools: hv: skip iso9660 mounts in hv_vss_daemon
tools: hv: use FIFREEZE/FITHAW in hv_vss_daemon
tools: hv: use getmntent in hv_vss_daemon
Tools: hv: Fix a checkpatch warning
tools: hv: fix checks for origin of netlink message in hv_vss_daemon
Tools: hv: fix warnings in hv_vss_daemon
misc: mark spear13xx-pcie-gadget as broken
mei: fix krealloc() misuse in in mei_cl_irq_read_msg()
mei: reduce flow control only for completed messages
mei: reseting -> resetting
mei: fix reading large reposnes
mei: revamp mei_irq_read_client_message function
mei: revamp mei_amthif_irq_read_message
mei: revamp hbm state machine
Revert "drivers/scsi: use module_pcmcia_driver() in pcmcia drivers"
Revert "scsi: pcmcia: nsp_cs: remove module init/exit function prototypes"
scsi: pcmcia: nsp_cs: remove module init/exit function prototypes
mei: wd: fix line over 80 characters
misc: tsl2550: Use dev_pm_ops
...
This patch allows timeriomem_rng to be used via devicetree.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
timeriomem_rng only supports a single device instance. This patch
enables multiple timeriomem_rng devices to coexist as well as adds
some additional error checking.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds a driver for random number generator present on Broadcom BCM2835 SoC,
used in Raspberry Pi and Roku 2 devices.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: linux-rpi-kernel@lists.infradead.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is my example conversion of a few existing mmap users. The HPET
case is simple, widely available, and easy to test (Clemens Ladisch sent
a trivial test-program for it).
Test-program-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the TPM has already been sent a SaveState command before the driver
is loaded it may have problems sending that same command again later.
This issue is seen with the Chromebook Pixel due to a firmware bug in
the legacy mode boot path which is sending the SaveState command
before booting the kernel. More information is available at
http://crbug.com/203524
This change introduces a retry of the SaveState command in the suspend
path in order to work around this issue. A future firmware update
should fix this but this is also a trivial workaround in the driver
that has no effect on systems that do not show this problem.
When this does happen the TPM responds with a non-fatal TPM_RETRY code
that is defined in the specification:
The TPM is too busy to respond to the command immediately, but the
command could be resubmitted at a later time. The TPM MAY return
TPM_RETRY for any command at any time.
It can take several seconds before the TPM will respond again. I
measured a typical time between 3 and 4 seconds and the timeout is set
at a safe 5 seconds.
It is also possible to reproduce this with commands via /dev/tpm0.
The bug linked above has a python script attached which can be used to
test for this problem. I tested a variety of TPMs from Infineon,
Nuvoton, Atmel, and STMicro but was only able to reproduce this with
LPC and I2C TPMs from Infineon.
The TPM specification only loosely defines this behavior:
TPM Main Level 2 Part 3 v1.2 r116, section 3.3. TPM_SaveState:
The TPM MAY declare all preserved values invalid in response to any
command other than TPM_Init.
TCG PC Client BIOS Spec 1.21 section 8.3.1.
After issuing a TPM_SaveState command, the OS SHOULD NOT issue TPM
commands before transitioning to S3 without issuing another
TPM_SaveState command.
TCG PC Client TIS 1.21, section 4. Power Management:
The TPM_SaveState command allows a Static OS to indicate to the TPM
that the platform may enter a low power state where the TPM will be
required to enter into the D3 power state. The use of the term "may"
is significant in that there is no requirement for the platform to
actually enter the low power state after sending the TPM_SaveState
command. The software may, in fact, send subsequent commands after
sending the TPM_SaveState command.
Change-Id: I52b41e826412688e5b6c8ddd3bb16409939704e9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Returning EMFILE (process has too many open files) is incorrect to
indicate a port is already open by another process. Use EBUSY for that.
This does change what we report to userspace, but I believe userspace
can look at it this way: it gets EBUSY, a new error code, instead of
EMFILE. It's still an error, and that's not changing.
Reported-by: Mateusz Guzik <mguzik@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Kent Yoder indicated that the code might be a bit clearer with a comment
here, so this patch adds a small explanation of the code.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
As the subject says.
It's probably a good idea to have these fields populated.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This driver adds support for Infineon's new SLB 9645 TT 1.2 I2C TPMs,
which supports clockstretching, combined reads and a bus speed of
up to 400khz. The device also has a new device id.
The driver works now also fine with device trees, so you can
instantiate your device by adding:
+ tpm {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ };
for SLB 9645 devices or
+ tpm {
+ compatible = "infineon,slb9635tt";
+ reg = <0x20>;
+ };
for SLB 9635 devices
to your device tree.
tpm_i2c_infineon is also retained as a compatible id as a fallback to
slb9635 protocol.
The driver was tested on Beaglebone.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Thanks to Julia Lawall for automating the conversion.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Ensure that the 'version' string includes a NULL terminator after its
copied out of the acpi table.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Those symbols only used within this file, and should be static.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When multiple ovq operations are being performed (lots of open/close
operations on virtio_console fds), the __send_control_msg() function can
get confused without locking.
A simple recipe to cause badness is:
* create a QEMU VM with two virtio-serial ports
* in the guest, do
while true;do echo abc >/dev/vport0p1;done
while true;do echo edf >/dev/vport0p2;done
In one run, this caused a panic in __send_control_msg(). In another, I
got
virtio_console virtio0: control-o:id 0 is not a head!
This also results repeated messages similar to these on the host:
qemu-kvm: virtio-serial-bus: Unexpected port id 478762112 for device virtio-serial-bus.0
qemu-kvm: virtio-serial-bus: Unexpected port id 478762368 for device virtio-serial-bus.0
Reported-by: FuXiangChun <xfu@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
The cvq_lock was taken for the c_ivq. Rename the lock to make that
obvious.
We'll also add a lock around the c_ovq in the next commit, so there's no
ambiguity.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gc7f
-----END PGP SIGNATURE-----
Merge tag 'arizona-extcon-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
ASoC/extcon: arizona: Fix interaction between HPDET and headphone outputs
This patch series covers both ASoC and extcon subsystems and fixes an
interaction between the HPDET function and the headphone outputs - we
really shouldn't run HPDET while the headphone is active. The first
patch is a refactoring to make the extcon side easier.
Used PTR_RET function instead of IS_ERR and PTR_ERR.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using devm_ioremap_resource() can make the code cleaner and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds CONFIG_PM_SLEEP to suspend/resume functions to fix
the following build warning when CONFIG_PM_SLEEP is not selected.
drivers/char/hw_random/exynos-rng.c:147:12: warning: 'exynos_rng_runtime_suspend' defined but not used [-Wunused-function]
drivers/char/hw_random/exynos-rng.c:157:12: warning: 'exynos_rng_runtime_resume' defined but not used [-Wunused-function]
Add CONFIG_PM_RUNTIME to suspend/resume functions to fix the build
error. It is because UNIVERSAL_DEV_PM_OPS macro is related to both
CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME.
drivers/char/hw_random/exynos-rng.c:167:8: error: 'exynos_rng_runtime_suspend' undeclared here (not in a function)
drivers/char/hw_random/exynos-rng.c:167:8: error: 'exynos_rng_runtime_resume' undeclared here (not in a function)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reported-by: David Rientjes <rientjes@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Takao Indoh
Arnd Bergmann
Benjamin Herrenschmidt
Corey Minyard
David Vrabel
Pawel Moll
Sudip Mukherjee
Eli Billauer
Steven Honeyman
Michal Simek
Daniel Vetter
Amos Kong
Feng Kan
Christoph Lameter
Amit Shah
Linus Torvalds
Stephen Boyd
Theodore Ts'o
Dave Airlie
Mathias Krause
Andy Shevchenko
Jason Gunthorpe
Jarkko Sakkinen
Stefan Berger
Fabian Frederick
Thomas Gleixner
Hannes Frederic Sowa
Andrey Utkin
Torsten Duwe
Greg Kroah-Hartman
Peter Hurley
Dan Carpenter
Kees Cook
Guenter Roeck
Al Viro
Joe Perches
Rafael J. Wysocki
Lv Zheng
Ingo Molnar
Sasha Levin
Himangi Saraogi
Jingoo Han
Christoph Hellwig
Dongsheng Yang
Bodo Stroesser
Jiri Slaby
Jean Delvare
Takashi Iwai
Paul Bolle
Matt Porter
Uwe Kleine-König
H. Peter Anvin
Greg Price
Rusty Russell
Kumar Gala
Petr Tesarik
Paul Gortmaker
Geert Uytterhoeven
Jean Delvare
Xie XiuQi
Michael Opdenacker
Grygorii Strashko
Bjorn Helgaas
Yinghai Lu
Bin Shi
Fengguang Wu
Michal Nazarewicz
Peter Huewe
Jiang Liu
Konrad Rzeszutek Wilk
Masanari Iida
Jiri Kosina
Yongjian Xu
Alan Cox
Alan
Wolfram Sang
Prarit Bhargava
Rob Herring
Ville Syrjälä
Stanimir Varbanov
Heinz Graalfs
Pali Rohár
Michael Ellerman
H. Peter Anvin
Elad Wexler
Tomas Winkler
Aaron Lu
Martin Schwidefsky
Ben Hutchings
Shuah Khan
Herbert Xu
Thomas Bogendoerfer
Jordan_Hargrave@Dell.com
Olof Johansson
Julia Lawall
Daniel De Graaf
Lokesh Vutla
Fabio Estevam
Alex Ivanov
Alexandru Juncu
Yoshihiro YUNOMAE
Thomas Renninger
Zhang Yanfei
Lars-Peter Clausen
Yijing Wang
Thomas Petazzoni
David Daney
Rasmus Villemoes
Gu Zheng
Linus Walleij
Stephen Rothwell
Andy Lutomirski
Michal Simek
Jarod Wilson
Mimi Zohar
Wei Yongjun
Darrick J. Wong
Libin
salina@us.ibm.com
Benjamin LaHaise
Chen Gang
Alexandru Gheorghiu
Kent Overstreet
Zach Brown
David Howells
Alexander Clouter
Lubomir Rintel
Duncan Laurie
Sachin Kamat
Peter Huewe
Shubhrajyoti Datta