When USB is in super-speed mode and disabled as a wakeup source,
observed that on the resume path, lanes have not been configured
properly in the phy-zynqmp driver.
As a result, after the resume, USB device detection failed on host.
To resolved the above issue, added phy_init on resume and phy_exit
on suspend path, to configure the GT lanes correctly.
The re-initialization of phy, reset the device and re-enumerate
the USB subsystem.
This use-case is specific to Xilinx ZynqMP SoC.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20220912111017.901321-3-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added system sleep and run-time power management ops support for
dwc3-xilinx glue layer and update function name.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20220912111017.901321-2-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All Qualcomm SoC DWC3 USB devices have a qcom,dwc3 fallback, thus there
is no need to keep the list of compatibles growing.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220921084654.118230-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3_EP_DELAYED_STOP is utilized to defer issuing the end transfer command
until the subsequent SETUP stage, in order to avoid end transfer timeouts.
During cable disconnect scenarios, __dwc3_gadget_ep_disable() is
responsible for ensuring endpoints have no active transfers pending. Since
dwc3_remove_request() can now exit early if the EP delayed stop is set,
avoid clearing all DEP flags, otherwise the transition back into the SETUP
stage won't issue an endxfer command.
Fixes: 2b2da6574e ("usb: dwc3: Avoid unmapping USB requests if endxfer is not complete")
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220919231213.21364-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some DWC3 controllers (e.g. Rockchip SoCs), the DWC3 core
doesn't support 64-bit DMA address width. In this case, this
driver should use the default 32-bit mask. Otherwise, the DWC3
controller will break if it runs on above 4GB physical memory
environment.
This patch reads the DWC_USB3_AWIDTH bits of GHWPARAMS0 which
used for the DMA address width, and only configure 64-bit DMA
mask if the DWC_USB3_AWIDTH is 64.
Fixes: 45d39448b4 ("usb: dwc3: support 64 bit DMA in platform driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/20220901083446.3799754-1-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a cable disconnect sequence, if ep0state is not in the SETUP phase,
then nothing will trigger any pending end transfer commands. Force
stopping of any pending SETUP transaction, and move back to the SETUP
phase.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-6-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For endxfer commands that do not require an endpoint complete interrupt,
avoid having to wait for the command active bit to clear. This allows for
EP0 events to continue to be handled, which allows for the controller to
complete it. Otherwise, it is known that the endxfer command will fail if
there is a pending SETUP token that needs to be read.
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since EP0 transactions need to be completed before the controller halt
sequence is finished, this may take some time depending on the host and the
enabled functions. Increase the controller halt timeout, so that we give
the controller sufficient time to handle EP0 transfers.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the need for making dwc3_gadget_suspend() and dwc3_gadget_resume()
to be called in a spinlock, as dwc3_gadget_run_stop() could potentially
take some time to complete.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DWC3_EP_DELAYED_STOP is set during stop active transfers, then do not
continue attempting to unmap request buffers during dwc3_remove_requests().
This can lead to SMMU faults, as the controller has not stopped the
processing of the TRB. Defer this sequence to the EP0 out start, which
ensures that there are no pending SETUP transactions before issuing the
endxfer.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220901193625.8727-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves the merge issue in:
drivers/usb/dwc3/gadget.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During soft disconnect, EP0 events are expected to be handled in order to
allow the controller to successfully move into the halted state. Since
__dwc3_gadget_stop() is executed before polling, EP0 has been disabled, and
events are being blocked. Allow xfercomplete events to be handled, so that
cached SETUP packets can be read out from the internal controller memory.
Without doing so, it will lead to endxfer timeouts, which results to
controller halt failures.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-5-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that there are no pending events being handled in between soft
connect/disconnect transitions. As we are keeping interrupts enabled,
and EP0 events are still being serviced, this avoids any stale events from
being serviced.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If any function drivers request for a delayed status phase, this leads to a
SETUP transfer timeout error, since the function may take longer to process
the DATA stage. This eventually results in end transfer timeouts, as there
is a pending SETUP transaction.
In addition, allow the DWC3_EP_DELAY_STOP to be set for if there is a
delayed status requested. Ocasionally, a host may abort the current SETUP
transaction, by issuing a subsequent SETUP token. In those situations, it
would result in an endxfer timeout as well.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-3-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some operations that need to be ignored if there is a soft
disconnect in progress. This is to avoid having a pending EP0 transfer in
progress while attempting to stop active transfers and halting the
controller.
There were several instances seen where a soft disconnect was able to occur
during early link negotiation, i.e. bus reset/conndone, which leads to the
conndone handler re-configuring EPs while attempting to halt the
controller, as DEP flags are cleared as part of the soft disconnect path.
ep0out: cmd 'Start New Configuration'
ep0out: cmd 'Set Endpoint Transfer Resource'
ep0in: cmd 'Set Endpoint Transfer Resource'
ep1out: cmd 'Set Endpoint Transfer Resource'
...
event (00030601): Suspend [U3]
event (00000101): Reset [U0]
ep0out: req ffffff87e5c9e100 length 0/0 zsI ==> 0
event (00000201): Connection Done [U0]
ep0out: cmd 'Start New Configuration'
ep0out: cmd 'Set Endpoint Transfer Resource'
In addition, if a soft disconnect occurs, EP0 events are still allowed to
process, however, it will stall/restart during the SETUP phase. The
host is still able to query for the DATA phase, leading to a
xfernotready(DATA) event. Since none of the SETUP transfer parameters are
populated, the xfernotready is treated as a "wrong direction" error,
leading to a duplicate stall/restart routine.
Add the proper softconnect/connected checks in sequences that are
potentially involved during soft disconnect processing.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220817182359.13550-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 driver manages its PHYs itself so the USB core PHY management
needs to be disabled.
Use the struct xhci_plat_priv hack added by commits 46034a999c ("usb:
host: xhci-plat: add platform data support") and f768e71891 ("usb:
host: xhci-plat: add priv quirk for skip PHY initialization") to
propagate the setting for now.
Fixes: 4e88d4c083 ("usb: add a flag to skip PHY initialization to struct usb_hcd")
Fixes: 178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD core")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Cc: stable <stable@kernel.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220825131836.19769-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3_qcom_read_usb2_speed() helper is now only called when the
controller is acting as host, but the compiler will warn that the hcd
variable is unused in gadget-only W=1 builds.
Fixes: c06795f114 ("usb: dwc3: qcom: fix gadget-only builds")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220822100550.3039-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the interconnect-initialisation helper by increasing
indentation of (or merging) continuation lines and adding brackets
around multi-line blocks in order to improve readability.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220805074500.21469-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a temporary variable to the interconnect-initialisation helper to
avoid parsing and decoding the 'maximum-speed' devicetree property
twice.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220805074500.21469-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having the Start of Frame Number in the trace data is useful for debugging.
This patch adds the (micro)frame number in which the last packet of the
TRB's buffer was transmitted or received to the trace output.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720215113.1058313-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Printing the event parameters in decimal is not useful.
Print them in hex and make it more practical.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720215113.1058313-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions stop_active_transfers and ep_disable are both calling
remove_requests. This functions in both cases will giveback the requests
with status ESHUTDOWN, which also represents an physical disconnection.
For ep_disable this is not true. This patch adds the status parameter to
remove_requests and sets the status to ECONNRESET on ep_disable.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220720213523.1055897-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Relocate the pullups_connected check until after it is ensured that there
are no runtime PM transitions. If another context triggered the DWC3
core's runtime resume, it may have already enabled the Run/Stop. Do not
re-run the entire pullup sequence again, as it may issue a core soft
reset while Run/Stop is already set.
This patch depends on
commit 69e131d1ac ("usb: dwc3: gadget: Prevent repeat pullup()")
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220728020647.9377-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the necessary PCI device ID for the controller
inside the Intel Raptor Lake CPU block. The controllers that
are part of the PCH (chipset) have separate device IDs.
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220815123334.87526-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the suspend callbacks by separating the error and success paths
to improve readability.
Also drop a related redundant initialisation.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-10-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is the Qualcomm glue wakeup interrupts that may be able to wake the
system from suspend and this can now be described in the devicetree.
Move the wakeup-source property handling over from the core driver and
instead propagate the capability setting to the core device during
probe.
This is needed as there is currently no way for the core driver to query
the wakeup setting of the glue device, but it is the core driver that
manages the PHY power state during suspend.
Also don't leave the PHYs enabled when system wakeup has been disabled
through sysfs.
Fixes: 649f5c842b ("usb: dwc3: core: Host wake up support from system suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-9-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent commit implementing wakeup support in host mode instead broke
suspend for peripheral and OTG mode.
The hack that was added in the suspend path to determine the speed of
any device connected to the USB2 bus not only accesses internal driver
data for a child device, but also dereferences a NULL pointer or
accesses freed data when the controller is not acting as host.
There's no quick fix to the layering violation, but since reverting
would leave us with broken suspend in host mode with wakeup triggering
immediately, let's keep the hack for now.
Fix the immediate issues by only checking the host bus speed and
enabling wakeup interrupts when acting as host.
Fixes: 6895ea55c3 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-7-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A device must enable wakeups during runtime suspend regardless of
whether it is capable and allowed to wake the system up from system
suspend.
Fixes: 2664deb093 ("usb: dwc3: qcom: Honor wakeup enabled/disabled state")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-6-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm dwc3 runtime-PM implementation checks the xhci
platform-device pointer in the wakeup-interrupt handler to determine
whether the controller is in host mode and if so triggers a resume.
After a role switch in OTG mode the xhci platform-device would have been
freed and the next wakeup from runtime suspend would access the freed
memory.
Note that role switching is executed from a freezable workqueue, which
guarantees that the pointer is stable during suspend.
Also note that runtime PM has been broken since commit 2664deb093
("usb: dwc3: qcom: Honor wakeup enabled/disabled state"), which
incidentally also prevents this issue from being triggered.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-5-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change added a dependency to the USB host stack and broke
gadget-only builds of the driver.
Fixes: 6895ea55c3 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d9be8d5c5b.
Generic power-domain flags must be set before the power-domain is
initialised and must specifically not be modified by drivers for devices
that happen to be in the domain.
To make sure that USB power-domains are left enabled during system
suspend when a device in the domain is in the wakeup path, the
GENPD_FLAG_ACTIVE_WAKEUP flag should instead be set for the domain
unconditionally when it is registered.
Note that this also avoids keeping power-domains on during suspend when
wakeup has not been enabled (e.g. through sysfs).
For the runtime PM case, making sure that the PHYs are not suspended and
that they are in the same domain as the controller prevents the domain
from being suspended. If there are cases where this is not possible or
desirable, the genpd implementation may need to be extended.
Fixes: d9be8d5c5b ("usb: dwc3: qcom: Keep power domain on to retain controller status")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generic PHYs must be powered-off before they can be tore down.
Similarly, suspending legacy PHYs after having powered them off makes no
sense.
Fix the dwc3_core_exit() (e.g. called during suspend) and open-coded
dwc3_probe() error-path sequences that got this wrong.
Note that this makes dwc3_core_exit() match the dwc3_core_init() error
path with respect to powering off the PHYs.
Fixes: 03c1fd622f ("usb: dwc3: core: add phy cleanup for probe error handling")
Fixes: c499ff71ff ("usb: dwc3: core: re-factor init and exit paths")
Cc: stable@vger.kernel.org # 4.8
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all platforms have all of the four currently supported wakeup
interrupts so use the optional irq helpers when looking up interrupts to
avoid printing error messages when an optional interrupt is not found:
dwc3-qcom a6f8800.usb: error -ENXIO: IRQ hs_phy_irq not found
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220713131340.29401-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the programming guide, it is recommended to
perform a GCTL_CORE_SOFTRESET only when switching the mode
from device to host or host to device. However, it is found
that during bootup when __dwc3_set_mode() is called for the
first time, GCTL_CORESOFTRESET is done with suspendable bit(BIT 17)
of DWC3_GUSB3PIPECTL set. This some times leads to issues
like controller going into bad state and controller registers
reading value zero. Until GCTL_CORESOFTRESET is done and
run/stop bit is set core initialization is not complete.
Setting suspendable bit of DWC3_GUSB3PIPECTL and then
performing GCTL_CORESOFTRESET is therefore not recommended.
Avoid this by only performing the reset if current_dr_role is set,
that is, when doing subsequent role switching.
Fixes: f88359e158 ("usb: dwc3: core: Do core softreset when switch mode")
Signed-off-by: Rohith Kollalsi <quic_rkollals@quicinc.com>
Link: https://lore.kernel.org/r/20220714045625.20377-1-quic_rkollals@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a 3 stage SETUP transfer, if the host sends another SETUP token
before completing the status phase, it signifies that the host has aborted
the current control transfer. Currently, if a setup_packet_pending is
received, there are no subsequent calls to dwc3_ep0_out_start() to fetch
the new SETUP packet. This leads to a stall on EP0, as host does not
expect another STATUS phase as it has aborted the current transfer.
Fix this issue by explicitly stalling and restarting EP0, as well as
resetting the trb_enqueue indexes. (without this, there is a chance the
SETUP TRB is set up on trb_endqueue == 1)
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220712014403.2977-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For High-Speed Transfers the prepare_one_trb function is calculating the
multiplier setting for the trb based on the length parameter of the trb
currently prepared. This assumption is wrong. For trbs with a sg list,
the length of the actual request has to be taken instead.
Fixes: 40d829fb2e ("usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220704141812.1532306-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function __dwc3_prepare_one_trb has many parameters. Since it is
only used in dwc3_prepare_one_trb there is no point in keeping the
function. We merge both functions and get rid of the big list of
parameters.
Fixes: 40d829fb2e ("usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets")
Cc: stable <stable@kernel.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220704141812.1532306-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clk get by devm_clk_get() will be released in devres_release_all(),
so there is no need explicitly call clk_put(), or it will cause UAF.
Fixes: e8784c0aec ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220629094635.3116961-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DWC3_EVENT_PENDING flag is used to protect against invalid call to
top-half interrupt handler, which can occur when there's a delay in
software detection of the interrupt line deassertion.
However, the clearing of this flag was done prior to unmasking the
interrupt line, creating opportunity where the top-half handler can
come. This breaks the serialization and creates a race between the
top-half and bottom-half handler, resulting in losing synchronization
between the controller and the driver when processing events.
To fix this, make sure the clearing of the DWC3_EVENT_PENDING is done at
the end of the bottom-half handler.
Fixes: d325a1de49 ("usb: dwc3: gadget: Prevent losing events in event cache")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/8670aaf1cf52e7d1e6df2a827af2d77263b93b75.1656380429.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The multiplier parameter of dwc3_gadget_calc_tx_fifo_size() was
not documented:
drivers/usb/dwc3/gadget.c:675: warning: Function parameter or member 'mult' not described in 'dwc3_gadget_calc_tx_fifo_size'
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Link: https://lore.kernel.org/r/bd599a18cea45c57d91c69d3e30d8b1e8ea69dd1.1656409369.git.mchehab@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dwc3 is wakeup capable, keep the power domain always ON so that
wakeup from system suspend can be supported. Otherwise, keep the
power domain ON only during runtime suspend to support wakeup from
runtime suspend.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-6-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure DP/DM line interrupts based on the USB2 device attached to
the root hub port. When HS/FS device is connected, configure the DP line
as falling edge to detect both disconnect and remote wakeup scenarios. When
LS device is connected, configure DM line as falling edge to detect both
disconnect and remote wakeup. When no device is connected, configure both
DP and DM lines as rising edge to detect HS/HS/LS device connect scenario.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-5-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check wakeup-source property for dwc3 core node to set the
wakeup capability. Drop the device_init_wakeup call from
runtime suspend and resume.
If the dwc3 is wakeup capable, don't power down the USB PHY(s).
The glue drivers are expected to take care of configuring the
additional wakeup settings if needed based on the dwc3 wakeup
capability status. In some SOC designs, powering off the PHY is
resulting in higher leakage, so this patch save power on such boards.
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1655094654-24052-3-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys IP DWC_usb32 and DWC_usb31 version 1.90a and above deprecated
GCTL.CORESOFTRESET. The DRD mode switching flow is updated to remove the
GCTL soft reset. Add version checks to prevent using deprecated setting
in mode switching flow.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9df529fde6e55f5508321b6bc26e92848044ef2b.1655338967.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmKvgdceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG0qMH/RnVz4BvYXVWWc1t
+4NT9N20pNzrByzUxSBsrLfL5BNIt9fNjrS0WLs4HlzExbiixvKIBHPkDZoCo1gQ
wxoqpJf2BMxmdXH46/wWdSszbdPk33eLM/MfYE2QfnmtYsDSLZQMzOUAcdh6qD53
ty9br3IM/g4ixCwxKRt3NNixjin4wTTxR5ZD2E5k0JAaT+4FW5llRvq92dA1UOq7
JeGRLkc2l0211MFLo0vtuPOyWMIQL8t98rKTzevwoVY7R9I/0uUJCbkU7mb9wMUY
yKYlTN/4ZikTTSxa8NpQsXHqTyOHaKmS5F6oE4sw9VurHI2u3Jmxy9j9AwO1Pn8C
JUizMCk=
=qqcu
-----END PGP SIGNATURE-----
Merge v5.19-rc3 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 57303488cd ("usb: dwc3: adapt dwc3 core to use Generic PHY
Framework") added if statements that check 'ret == -ENOSYS || ret ==
-ENODEV', but the function phy_get() which is called by devm_phy_get()
returns the phy driver or -ENODEV if the phy driver was not found. So,
remove the check of -ENOSYS in the if statements.
Signed-off-by: Kushagra Verma <kushagra765@outlook.com>
Link: https://lore.kernel.org/r/HK0PR01MB2801E19D4FE569545BB7592DF8A19@HK0PR01MB2801.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoC(e.g NXP imx8MQ) may have a wrong default power down scale
setting so need init it to be the correct value, the power down
scale setting description in DWC3 databook:
Power Down Scale (PwrDnScale)
The USB3 suspend_clk input replaces pipe3_rx_pclk as a clock source to
a small part of the USB3 core that operates when the SS PHY is in its
lowest power (P3) state, and therefore does not provide a clock.
The Power Down Scale field specifies how many suspend_clk periods fit
into a 16 kHz clock period. When performing the division, round up the
remainder.
For example, when using an 8-bit/16-bit/32-bit PHY and 25-MHz Suspend
clock,
Power Down Scale = 25000 kHz/16 kHz = 13'd1563 (rounder up)
So use the suspend clock rate to calculate it.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1654568404-3461-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Today's linux-next merge of the extcon tree got a conflict in:
drivers/usb/dwc3/drd.c
between commit:
0f01017191 ("usb: dwc3: Don't switch OTG -> peripheral if extcon is present")
from the usb tree and commit:
88490c7f43c4 ("extcon: Fix extcon_get_extcon_dev() error handling")
from the extcon tree.
I fixed it up (the former moved the code modified by the latter, so I
used the former version of this files and added the following merge fix
patch) and can carry the fix as necessary.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220426152739.62f6836e@canb.auug.org.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 582ab24e09 ("usb: dwc3: pci: Set "linux,phy_charger_detect"
property on some Bay Trail boards") added a new swnode similar to the
existing ones for boards where the PHY handles charger detection.
Unfortunately, the "linux,sysdev_is_parent" property got lost in the
merge conflict resolution of commit ca9400ef7f ("Merge 5.17-rc6 into
usb-next"). Now dwc3_pci_intel_phy_charger_detect_properties is the
only swnode in dwc3-pci that is missing "linux,sysdev_is_parent".
It does not seem to cause any obvious functional issues, but it's
certainly unintended so restore the line to make the properties
consistent again.
Fixes: ca9400ef7f ("Merge 5.17-rc6 into usb-next")
Cc: stable@vger.kernel.org
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20220528170913.9240-1-stephan@gerhold.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current logic to assign the max packet limit for IN endpoints attempts
to take the default HW value and apply the optimal endpoint settings based
on it. However, if the default value reports a TxFIFO size large enough
for only one max packet, it will divide the value and assign a smaller ep
max packet limit.
For example, if the default TxFIFO size fits 1024B, current logic will
assign 1024/3 = 341B to ep max packet size. If function drivers attempt to
request for an endpoint with a wMaxPacketSize of 1024B (SS BULK max packet
size) then it will fail, as the gadget is unable to find an endpoint which
can fit the requested size.
Functionally, if the TxFIFO has enough space to fit one max packet, it will
be sufficient, at least when initializing the endpoints.
Fixes: d94ea53198 ("usb: dwc3: gadget: Properly set maxpacket limit")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220523213948.22142-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 controller soft reset is important operation for USB functionality.
In case when it fails, currently there is no failure log. Hence add
error log when core soft reset failed.
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
Link: https://lore.kernel.org/r/1652897572-14461-1-git-send-email-quic_mrana@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When dwc3_gadget_ep_cleanup_completed_requests() called to
dwc3_gadget_giveback() where the dwc3 lock is released, other thread is
able to execute. In this situation, usb_ep_disable() gets the chance to
clear endpoint descriptor pointer which leds to the null pointer
dereference problem. So needs to move the null pointer check to a proper
place.
Example call stack:
Thread#1:
dwc3_thread_interrupt()
spin_lock
-> dwc3_process_event_buf()
-> dwc3_process_event_entry()
-> dwc3_endpoint_interrupt()
-> dwc3_gadget_endpoint_trbs_complete()
-> dwc3_gadget_ep_cleanup_completed_requests()
...
-> dwc3_giveback()
spin_unlock
Thread#2 executes
Thread#2:
configfs_composite_disconnect()
-> __composite_disconnect()
-> ffs_func_disable()
-> ffs_func_set_alt()
-> ffs_func_eps_disable()
-> usb_ep_disable()
wait for dwc3 spin_lock
Thread#1 released lock
clear endpoint.desc
Fixes: 2628844812 ("usb: dwc3: gadget: Fix null pointer exception")
Cc: stable <stable@kernel.org>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20220518061315.3359198-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the databook ep0 should be in setup phase during reset.
If host issues reset between control transfers, ep0 will be in an
invalid state. Fix this by issuing stall and restart on ep0 if it
is not in setup phase.
Also SW needs to complete pending control transfer and setup core for
next setup stage as per data book. Hence check ep0 state during reset
interrupt handling and make sure active transfers on ep0 out/in
endpoint are stopped by queuing ENDXFER command for that endpoint and
restart ep0 out again to receive next setup packet.
Signed-off-by: Mayank Rana <quic_mrana@quicinc.com>
Link: https://lore.kernel.org/r/1651693001-29891-1-git-send-email-quic_mrana@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the controller hasn't DMA'ed the Setup data from its fifo, it won't
process the End Transfer command. Polling for the command completion may
block the driver from servicing the Setup phase and cause a timeout.
Previously we only check and delay issuing End Transfer in the case of
endpoint dequeue. Let's do that for all End Transfer scenarios.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/2fcf3b5d90068d549589a57a27a79f76c6769b04.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver shouldn't be able to issue End Transfer to the control
endpoint at anytime. Typically we should only do so in error cases such
as invalid/unexpected direction of Data Phase as described in the
control transfer flow of the programming guide. It _may_ end started
data phase during controller deinitialization from soft disconnect or
driver removal. However, that should not happen because the driver
should be maintained in EP0_SETUP_PHASE during driver tear-down. On
soft-connect, the controller should be reset from a soft-reset and there
should be no issue starting the control endpoint.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3c6643678863a26702e4115e9e19d7d94a30d49c.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we can't guarantee that the host won't send new Setup packet
before going through the device-initiated disconnect, don't prepare
beyond the Setup stage and keep the device in EP0_SETUP_PHASE. This
ensures that the device-initated disconnect sequence can go through
gracefully. Note that the controller won't service the End Transfer
command if it can't DMA out the Setup packet.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6bacec56ecabb2c6e49a09cedfcac281fdc97de0.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the GEVNTCOUNT indicates events in the event buffer, the driver needs
to acknowledge them before the controller can halt. Simply let the
interrupt handler acknowledges the remaining event generated by the
controller while polling for DSTS.DEVCTLHLT. This avoids disabling irq
and taking care of race condition between the interrupt handlers and
pullup().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ea306ec93c41ccafbdb5d16404ff3b6eca299613.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't do soft-disconnect if it's previously done. Likewise, don't do
soft-connect if the device is currently connected and running. It would
break normal operation.
Currently the caller of pullup() (udc's sysfs soft_connect) only checks
if it had initiated disconnect to prevent repeating soft-disconnect. It
doesn't check for soft-connect. To be safe, let's keep the check here
regardless whether the udc core is fixed.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1c1345bd66c97a9d32f77d63aaadd04b7b037143.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a USB GPIO based reset for dwc3-xilinx driver. The PHY
needs to be reset after the completion of phy initialization. As part
of the reset, check for gpio-reset binding before toggling the pin.
This feature is advantageous when the user toggle GPIO to trigger the
ULPI-PHY reset.
Delay of milliseconds is added in between low and high to meet the setup
and hold time requirement of the reset. The reset-gpio error handling is
added for error notification.
Some GPIO controllers must be accessed using message-based buses, like
I2C or SPI, to address this problem, updates GPIO access with sleep API.
This reset is specific to the zynqMp.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Link: https://lore.kernel.org/r/20220504075309.6244-3-piyush.mehta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is no longer needed. The sysdev pointer is now used when
assigning the ACPI companions to the xHCI ports and USB
devices.
Assigning the ACPI companion here resulted in the
fwnode->secondary pointer to be replaced also for the parent
dwc3 device since the primary fwnode (the ACPI companion)
was shared. That was unintentional and it created potential
side effects like resource leaks.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220428111056.3558-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
Fixes: 6d8a019614 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/db2c80108286cfd108adb05bad52138b78d7c3a7.1650673655.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Fixes: 8eed00b237 ("usb: dwc3: pci: Runtime resume child device from wq")
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220422062652.10575-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The list_for_each_entry_safe() macro saves the current item (n) and
the item after (n+1), so that n can be safely removed without
corrupting the list. However, when traversing the list and removing
items using gadget giveback, the DWC3 lock is briefly released,
allowing other routines to execute. There is a situation where, while
items are being removed from the cancelled_list using
dwc3_gadget_ep_cleanup_cancelled_requests(), the pullup disable
routine is running in parallel (due to UDC unbind). As the cleanup
routine removes n, and the pullup disable removes n+1, once the
cleanup retakes the DWC3 lock, it references a request who was already
removed/handled. With list debug enabled, this leads to a panic.
Ensure all instances of the macro are replaced where gadget giveback
is used.
Example call stack:
Thread#1:
__dwc3_gadget_ep_set_halt() - CLEAR HALT
-> dwc3_gadget_ep_cleanup_cancelled_requests()
->list_for_each_entry_safe()
->dwc3_gadget_giveback(n)
->dwc3_gadget_del_and_unmap_request()- n deleted[cancelled_list]
->spin_unlock
->Thread#2 executes
...
->dwc3_gadget_giveback(n+1)
->Already removed!
Thread#2:
dwc3_gadget_pullup()
->waiting for dwc3 spin_lock
...
->Thread#1 released lock
->dwc3_stop_active_transfers()
->dwc3_remove_requests()
->fetches n+1 item from cancelled_list (n removed by Thread#1)
->dwc3_gadget_giveback()
->dwc3_gadget_del_and_unmap_request()- n+1 deleted[cancelled_list]
->spin_unlock
Fixes: d4f1afe5e8 ("usb: dwc3: gadget: move requests to cancelled_list")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220414183521.23451-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_ep_clear_halt() API can be called from the function driver, and
translates to dwc3_gadget_ep_set_halt(). This routine is shared with when
the host issues a clear feature ENDPOINT_HALT, and is differentiated by the
protocol argument. If the following sequence occurs, there can be a
situation where the delayed_status flag is improperly cleared for the wrong
SETUP transaction:
1. Vendor specific control transfer returns USB_GADGET_DELAYED_STATUS.
2. DWC3 gadget sets dwc->delayed_status to '1'.
3. Another function driver issues a usb_ep_clear_halt() call.
4. DWC3 gadget issues dwc3_stop_active_transfer() and sets
DWC3_EP_PENDING_CLEAR_STALL.
5. EP command complete interrupt triggers for the end transfer, and
dwc3_ep0_send_delayed_status() is allowed to run, as delayed_status
is '1' due to step#1.
6. STATUS phase is sent, and delayed_status is cleared.
7. Vendor specific control transfer is finished being handled, and issues
usb_composite_setup_continue(). This results in queuing of a data
phase.
Cache the protocol flag so that DWC3 gadget is aware of when the clear halt
is due to a SETUP request from the host versus when it is sourced from a
function driver. This allows for the EP command complete interrupt to know
if it needs to issue a delayed status phase.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220414073902.21960-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure not to set run_stop bit or link state change request while
initiating soft-reset. Register read-modify-write operation may
unintentionally start the controller before the initialization completes
with its previous DCTL value, which can cause initialization failure.
Fixes: f59dcab176 ("usb: dwc3: core: improve reset sequence")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/6aecbd78328f102003d40ccf18ceeebd411d3703.1650594792.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the extcon device exists, get the mode from the extcon device. If
the controller is DRD and the driver is unable to determine the mode,
only then default the dr_mode to USB_DR_MODE_PERIPHERAL.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Link: https://lore.kernel.org/r/20220403164907.662860-1-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve performance of isoc transfers in superspeed by increasing the
number of possible endpoints available, matching that of what was
configured for bulk transfers.
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20220420183338.445622-1-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two kerneldoc comments in gadget.c have excess function parameter description or wrong
prototype name and one kerneldoc comment in core.c has an excess function parameter
description, resulting in these three doc-build warnings:
1. ./drivers/usb/dwc3/gadget.c:675: warning: Excess function parameter
'nfifos' description in 'dwc3_gadget_calc_tx_fifo_size'
2. ./drivers/usb/dwc3/gadget.c:700: warning: expecting prototype for
dwc3_gadget_clear_tx_fifo_size(). Prototype was for dwc3_gadget_clear_tx_fifos()
instead
3. ./drivers/usb/dwc3/core.c:347: warning: Excess function parameter 'ref_clk_per'
description in 'dwc3_ref_clk_period'
Fix the warnings by correcting the prototype name and removing excess parameter descriptions.
Signed-off-by: Kushagra Verma <kushagra765@outlook.com>
Link: https://lore.kernel.org/r/SI2PR01MB392995043CACD80884A13764F81C9@SI2PR01MB3929.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the PHY controller node has a "port" dwc3 tries to find an
extcon device even when "usb-role-switch" is present. This happens
because dwc3_get_extcon() sees that "port" node and then calls
extcon_find_edev_by_node() which will always return EPROBE_DEFER
in that case.
On the other hand, even if an extcon was present and dwc3_get_extcon()
was successful it would still be ignored in favor of "usb-role-switch".
Let's just first check if "usb-role-switch" is configured in the device
tree and directly use it instead and only try to look for an extcon
device otherwise.
Fixes: 8a0a137997 ("usb: dwc3: Registering a role switch in the DRD code.")
Cc: stable <stable@kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20220411155300.9766-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver logic checks against 0 to determine whether the
periodic tx/rx threshold settings are set, but we may get bogus values
from uninitialized variables if no device property is set. Properly
default these variables to 0.
Fixes: 938a5ad1d3 ("usb: dwc3: Check for ESS TX/RX threshold config")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cccfce990b11b730b0dae42f9d217dc6fb988c90.1649727139.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 33fb697ec7 ("usb: dwc3: Get clocks individually") moved from
the clk_bulk api to individual clocks, following the snps,dwc3.yaml
dt-binding for clock names.
Unfortunately the rk3328 (and upcoming rk356x support) use the
rockchip,dwc3.yaml which has different clock names, which are common on
devices using the glue layer.
The rk3328 does not use a glue layer, but attaches directly to the dwc3
core driver.
The offending patch series failed to account for this, thus dwc3 was
broken on rk3328.
To retain backwards compatibility with rk3328 device trees we must also
check for the alternate clock names.
Fixes: 33fb697ec7 ("usb: dwc3: Get clocks individually")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220409152116.3834354-1-pgwipeout@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In AM62 SoC, the Designware Core USB3 IP is progammed to operate in USB2.0
only mode. Add driver for AM62 USB DWC3 Wrapper.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20220414103211.16202-3-a-govindraju@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is recommended by the Synopsis databook to issue a DCTL.CSftReset
when reconnecting from a device-initiated disconnect routine. This
resolves issues with enumeration during fast composition switching
cases, which result in an unknown device on the host.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220316011358.3057-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a Setup packet is received but yet to DMA out, the controller will
not process the End Transfer command of any endpoint. Polling of its
DEPCMD.CmdAct may block setting up TRB for Setup packet, causing a
command timeout.
This may occur if the driver doesn’t service the completion interrupt of
the control status stage yet due to system latency, then it won’t
prepare TRB and start the transfer for the next Setup Stage. To the host
side, the control transfer had completed, and the host can send a new
Setup packet at this point.
In the meanwhile, if the driver receives an async call to dequeue a
request (triggering End Transfer) to any endpoint, then the driver will
service that End transfer first, blocking the control status stage
completion handler. Since no TRB is available for the Setup stage, the
Setup packet can’t be DMA’ed out and the End Transfer gets hung.
The driver must not block setting up of the Setup stage. So track and
only issue the End Transfer command only when there’s Setup TRB prepared
so that the controller can DMA out the Setup packet. Delay the End
transfer command if there's no Setup TRB available. This is applicable to
all DWC_usb3x IPs.
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220309205402.4467-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To improve reading the code this patch moves the cases to start_isoc or
return the function under one common condition check.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220306211251.2281335-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the PCI device ID and update the dwc3_pci_id_table
for Intel Alder Lake SoC.
The DWC3 controllor in the CPU block handles the USB3 traffic
and the device ID is common across the Alder Lake platforms.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20220308170848.30722-1-shruthi.sanil@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver will schedule isoc transfers immediately on the
next interval, which is quite aggressive when the interval is 125us.
There's report that some platforms may need more time to process the
transfer, otherwise the controller may miss the first interval. Let's
keep it simple and give the controller at least 500us to schedule the
isoc transfer.
Link: https://lore.kernel.org/linux-usb/20220302143539.GI11577@pengutronix.de/
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/deb8146b8e1f7f8495ef2d5647017270934cb2d8.1646708142.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the 3.0 device core, if the core is programmed to operate in
2.0 only, then setting the GUCTL1.DEV_FORCE_20_CLK_FOR_30_CLK makes
the internal 2.0(utmi/ulpi) clock to be routed as the 3.0 (pipe)
clock. Enabling this feature allows the pipe3 clock to be not-running
when forcibly operating in 2.0 device mode.
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Bin Yang <yangbin@rock-chips.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20220228135700.1089526-6-pgwipeout@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i.MX8MP glue layer has support for the following flags:
* over-current polarity
* PWR pad polarity
* controlling PPC flag in HCCPARAMS register
* permanent port attach for usb2 & usb3 port
Allow setting these flags by supporting specific flags in the glue node.
In order to get this to work an additional IORESOURCE_MEM and clock is
necessary. For backward compatibility this is purely optional.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220218152707.2198357-4-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until now the iomem used is not USB glue as the name suggests, but
HSIO BLK_CTL. Rename the struct member accordingly. This is a preparing
patch for when USB glue is actually used.
Reviewed-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220218152707.2198357-2-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constify the drvdata structs. This also matches the definition of
member drvdata in dwc3_meson_g12a.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/a3c178c9-7c33-d7b8-9f6e-734dc28728ab@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here, and it resolves a merge conflict in:
drivers/usb/dwc3/dwc3-pci.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
Link: https://lkml.kernel.org/r/c2a64979-73d1-2c22-e048-c275c9f81558@samsung.com
Fixes: e5f68b4a3e ("Revert "usb: dwc3: gadget: remove unnecessary _irqsave()"")
Cc: stable <stable@kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/Yg/YPejVQH3KkRVd@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for the phy driver to be able to actually get and control
the cs and reset GPIOs the dev_id member of the gpiod_lookup table must
be set to point to the dev_name() of the ulpi-device instantiated by
dwc3_ulpi_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-6-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Android x86 tablets with a Bay Trail (BYT) SoC and a Crystal Cove
PMIC, which does not support charger-detection, rely on the TUSB1211 phy
for charger-detection.
Windows tablets with the same SoC + PMIC often use an extra chip for
charger-detection like the FSA831A. But since on Android tablets
the designers already need to add a TUSB1211 phy to support device/gadget
mode the phy is used to do charger-detection instead.
These Android x86 tablets can be identified by the unique combination of
a Bay Trail SoC (already checked for by PCI-ids) + a Crystal Cove PMIC +
not using the standard ACPI battery and ac drivers. Where as on Windows
tablets the standard ACPI battery and ac drivers will be used on BYT
boards with a Crystal Cove PMIC.
Set a special kernel-internal (so not part of the dt-bindings)
"linux,phy_charger_detect" property on these boards, which tells the
tusb1210 driver to enable charger-detection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirk handling may need to set some different properties
which means using a different swnode, move the setting of the swnode
to inside dwc3_pci_quirks() so that the quirk handling can choose
a different swnode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_OF maybe set, but it may not be applicable to a device. In
such case, checking against that can cause the device fail to
initialize. Check against the device node (device->of_node) instead.
Fixes: a102f07e4e ("usb: dwc3: drd: Add support for usb-conn-gpio based usb-role-switch")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9f15580ad5810b1e5f31c241b35ebedfbfc30a3f.1644964864.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e0082698b6 ("usb: dwc3: ulpi: conditionally resume ULPI PHY")
fixed an issue where ULPI transfers would timeout if any requests where
send to the phy sometime after init, giving it enough time to auto-suspend.
Commit e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend
regression") changed the behavior to instead of clearing the
DWC3_GUSB2PHYCFG_SUSPHY bit, add an extra sleep when it is set.
But on Bay Trail devices, when phy_set_mode() gets called during init,
this leads to errors like these:
[ 28.451522] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
[ 28.464089] tusb1210 dwc3.ulpi: error -110 writing val 0x01 to reg 0x0a
Add "snps,dis_u2_susphy_quirk" to the settings for Bay Trail devices to
fix this. This restores the old behavior for Bay Trail devices, since
previously the DWC3_GUSB2PHYCFG_SUSPHY bit would get cleared on the first
ulpi_read/_write() and then was never set again.
Fixes: e5f4ca3fce ("usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression")
Cc: stable@kernel.org
Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmIJZmoeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZdoH/04d8zUhM3Fd3ACB
V/ONtOXmkfP2mEJSjb7cXTN1EM2SlOBdSnSsEw09FtGhjHABjOnLho4J5ixk9TH8
zNMNI3EMksM2T9KadHwxv8Vvp1LTrWRzMbws8tOCPA0RkOpikJfClC8CzRAyidJ3
cAbbDH/Jl1GnVZ8bpKmv2auYt+kNVGb0cwJ2W8phCwwkL7sLky5tgYeaGiJEXbJf
Tfi/3qtFdmYjD8wtYnCfzjnB7suG5nF7rGEnxCIxNi+IA4DieUv2c1KchuoaBfT9
df364VjKaGT3j+GB07ksQ/8mkwWiRXsCzOXAyMZSZaWjdMD4aAhCTJak5j7/TvGC
wtgHPww=
=/CMW
-----END PGP SIGNATURE-----
Merge 5.17-rc4 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With CPU re-ordering on write instructions, there might
be a chance that the HWO is set before the TRB is updated
with the new mapped buffer address.
And in the case where core is processing a list of TRBs
it is possible that it fetched the TRBs when the HWO is set
but before the buffer address is updated.
Prevent this by adding a memory barrier before the HWO
is updated to ensure that the core always process the
updated TRBs.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1644207958-18287-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GUCTL.REFCLKPER can only account for clock frequencies with integer
periods. To address this, program REFCLK_FLADJ with the relative error
caused by period truncation. The formula given in the register reference
has been rearranged to allow calculation based on rate (instead of
period), and to allow for fixed-point arithmetic.
Additionally, calculate a value for 240MHZDECR. This configures a
simulated 240Mhz clock using a counter with one fractional bit (PLS1).
This register is programmed only for versions >= 2.50a, since this is
the check also used by commit db2be4e9e3 ("usb: dwc3: Add frame length
adjustment quirk").
Tested-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127200636.1456175-5-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using a special property to determine the reference clock
period, use the rate of the reference clock. When we have a legacy
snps,ref-clock-period-ns property and no reference clock, use it
instead. Fractional clocks are not currently supported, and will be
dealt with in the next commit.
Tested-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127200636.1456175-4-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of grabbing all clocks in bulk, grab them individually. This will
allow us to get the frequency or otherwise deal with discrete clocks. This
may break some platforms if they use a clock which doesn't use one of the
documented names.
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127200636.1456175-3-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous patch to skip part of the initialization when a USB3 PHY was
not present could result in the return value being uninitialized in that
case, causing spurious probe failures. Initialize ret to 0 to avoid this.
Fixes: 9678f3361a ("usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode")
Cc: <stable@vger.kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220127221500.177021-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmH2lIMeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGWzkH/jmR4RpGgrV5SUHF
8R6tsIjae1WItJ8NoaDgImWRxLKXFU7MM77HoFykuZx5Y5yz5Xf5zuJNXRPrHQbC
lE/8wqWut89LX0+k/pKSzt8BQbyZzImfm5rOSBpMC9VkvMcbuQ8NSJ/YbJOD4iAp
jfRRIkJtLQWL6YRc/xPlHCfVY5Qx+TkNZuFFckPtM2HKIEXS225VCESX9JcABDcQ
j7zG5bq/H+8qGItD2iUg8Nw9hqrLutdKSOgP29wxVOajY5QWVczYr1J0nfyRSPMb
/Xs1Oo1/+zO+dfCmR45puJZYua+e/iFTJv2RPFLRIE2AV1vMq4WNIgTJlq8DwfQK
C7Jq080=
=6u+c
-----END PGP SIGNATURE-----
Merge tag 'v5.17-rc2' into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-conn-gpio devices are a subnode of the USB interface controller, which
needs to be populated.
This allows having a non-type-c connector providing dual-role.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220105071407.2240302-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code that looked up the USB3 PHY was ignoring all errors other than
EPROBE_DEFER in an attempt to handle the PHY not being present. Fix and
simplify the code by using devm_phy_optional_get and dev_err_probe so
that a missing PHY is not treated as an error and unexpected errors
are handled properly.
Fixes: 84770f028f ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-3-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that the PIPE clock should not be selected when only USB 2.0
is being used in the design and no USB 3.0 reference clock is used.
Also, the core resets are not required if a USB3 PHY is not in use, and
will break things if USB3 is actually used but the PHY entry is not
listed in the device tree.
Skip core resets and register settings that are only required for
USB3 mode when no USB3 PHY is specified in the device tree.
Fixes: 84770f028f ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-2-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the acpi_create_platform_device() function may return error
pointers, dwc3_qcom_create_urs_usb_platdev() function may return error
pointers too. Using IS_ERR_OR_NULL() to check the return value to fix this.
Fixes: c25c210f59 ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20211222111823.22887-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing platform_device_put() before return from
dwc3_qcom_acpi_register_core in the error handling case.
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20211231113641.31474-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop unneeded calls to platform_get_resource_byname() from
dwc3_host_init(). dwc3_host_init() already calls dwc3_host_get_irq()
which gets the irq number, just use this to get the IRQ resource data
and fill the xhci_resources[1]
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Synopsys introduced a new enhancement to DWC_usb32 called Multi-Stream
Transfer (MST) to improve bulk streams performance for SuperSpeed and
SuperSpeed Plus. This enhancement allows the controller to look ahead
and process multiple bulk streams.
Previously, to initiate a bulk stream transfer, the driver has to issue
Start Transfer command and wait for the stream to complete before
initiating a new stream. As a result, the controller does not process
TRBs beyond a single stream. With the enhancement, as long as there are
new requests, the dwc3 driver can keep preparing new TRBs and the
controller can keep caching and processing them without waiting for the
transfer completion.
The programming flow is similar to regular bulk endpoint with a few
additional rules:
1) Chained TRBs of the same stream must have a matching stream ID
2) The last TRB of a stream must have CHN=0
3) All the TRBs with LST=0 must have CSP=1
Depends on the application and usage, internal tests show significant
performance improvement in UASP transfers with this enhancement.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cd9c7a8bf11f790983ac546222dd114893f16b3a.1638242424.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cefdd52fa0.
On sc7180-trogdor class devices with 'fw_devlink=permissive' and KASAN
enabled, you'll see a Use-After-Free reported at bootup.
The root of the problem is that dwc3_qcom_of_register_core() is adding
a devm-allocated "tx-fifo-resize" property to its device tree node
using of_add_property().
The issue is that of_add_property() makes a _permanent_ addition to
the device tree that lasts until reboot. That means allocating memory
for the property using "devm" managed memory is a terrible idea since
that memory will be freed upon probe deferral or device unbinding.
Let's revert the patch since the system is still functional without
it. The fact that of_add_property() makes a permanent change is extra
fodder for those folks who were aruging that the device tree isn't
really the right way to pass information between parts of the
driver. It is an exercise left to the reader to submit a patch
re-adding the new feature in a way that makes everyone happier.
Fixes: cefdd52fa0 ("usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211207094327.1.Ie3cde3443039342e2963262a4c3ac36dc2c08b30@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver knows what it needs to set for GEVNTSIZn, and the controller
doesn't modify this register unless there's a hard reset. To save a few
microseconds of register read in read-modify-write operation, simply do
register write with the expected values. This can improve performance
when there are many interrupts generated, which the driver needs to
check and handle.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/efddf4ee5821c4bc5ae7ad90d629ec7a0ebcbf9a.1638240306.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The controller doesn't check for Update Transfer command parameters
DEPCMDPAR{0,1,2}. Writing to these registers is unnecessary. Ignoring
this improves performance slightly by removing the register write
delay.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/997d9ebf38c6bba920d4ee77bd8c77bf81978a55.1638240306.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we're not setting CMDACT (from "No Response" Update Transfer
command), then there's no point in checking for the command status. So
skip it. This can reduce a register read delay and improve performance.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/3dc31cf11581ae3ee82d9202dda3fc17d897d786.1638240306.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in case of a PCI dwc3 controller, leave the default DMA
mask. Calling of a 64 bit DMA mask breaks the driver on
cherrytrail based tablets like Cyberbook T116.
Fixes: 45d39448b4 ("usb: dwc3: support 64 bit DMA in platform driver")
Cc: stable <stable@vger.kernel.org>
Reported-by: Hans De Goede <hdegoede@redhat.com>
Tested-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Fabio Aiuto <fabioaiuto83@gmail.com>
Link: https://lore.kernel.org/r/20211113142959.27191-1-fabioaiuto83@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the endpoint interrupt functions
dwc3_gadget_endpoint_transfer_in_progress() and
dwc3_gadget_endpoint_trbs_complete() will dereference the endpoint
descriptor. But it could be cleared in __dwc3_gadget_ep_disable()
when accessory disconnected. So we need to check whether it is null
or not before dereferencing it.
Fixes: f09ddcfcb8 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jack Pham <quic_jackp@quicinc.com>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20211109092642.3507692-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The programming guide noted that the driver needs to verify if the link
state is in U0 before executing the Start Transfer command. If it's not
in U0, the driver needs to perform remote wakeup. This is not accurate.
If the link state is in U1/U2, then the controller will not respond to
link recovery request from DCTL.ULSTCHNGREQ. The Start Transfer command
will trigger a link recovery if it is in U1/U2. A clarification will be
added to the programming guide for all controller versions.
The current implementation shouldn't cause any functional issue. It may
occasionally report an invalid time out warning from failed link
recovery request. The driver will still go ahead with the Start Transfer
command if the remote wakeup fails. The new change only initiates remote
wakeup where it is needed, which is when the link state is in L1/L2/U3.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/05b4a5fbfbd0863fc9b1d7af934a366219e3d0b4.1635204761.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The End Transfer command from a stream endpoint will generate a NoStream
event, and we should ignore it. Currently we set the flag
DWC3_EP_IGNORE_NEXT_NOSTREAM to track this prior to sending the command,
and it will be cleared on the next stream event. However, a stream event
may be generated before the End Transfer command completion and
prematurely clear the flag. Fix this by setting the flag on End Transfer
completion instead.
Fixes: 140ca4cfea ("usb: dwc3: gadget: Handle stream transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/cee1253af4c3600edb878d11c9c08b040817ae23.1635203975.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During our predesign phase for DWC_usb32, the GHWPARAMS9 register offset
was 0xc680. We revised our final design, and the GHWPARAMS9 offset is
now moved to 0xc6e8 on release.
Fixes: 16710380d3 ("usb: dwc3: Capture new capability register GHWPARAMS9")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1541737108266a97208ff827805be1f32852590c.1635202893.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
reset_control_(de)assert() calls are called on a shared reset line when
reset_control_reset has been used. This is not allowed by the reset
framework.
Use reset_control_rearm() call in suspend() and remove() as a way to state
that the resource is no longer used, hence the shared reset line
may be triggered again by other devices. Use reset_control_rearm() also in
case probe fails after reset() has been called.
reset_control_rearm() keeps use of triggered_count sane in the reset
framework, use of reset_control_reset() on shared reset line should be
balanced with reset_control_rearm().
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20211112162827.128319-3-aouledameur@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the DWC3_EP_* flag macros so that the definitions are all
lined up on the same tab column for consistent style.
No functional change.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20211021180129.27938-2-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions may dynamically enable and disable their endpoints
regularly throughout their operation, particularly when Set Interface
is employed to switch between Alternate Settings. For instance the
UAC2 function has its respective endpoints for playback & capture
associated with AltSetting 1, in which case those endpoints would not
get enabled until the host activates the AltSetting. And they
conversely become disabled when the interfaces' AltSetting 0 is
chosen.
With the DWC3 FIFO resizing algorithm recently added, every
usb_ep_enable() call results in a call to resize that EP's TXFIFO,
but if the same endpoint is enabled again and again, this incorrectly
leads to FIFO RAM allocation exhaustion as the mechanism did not
account for the possibility that endpoints can be re-enabled many
times.
Example log splat:
dwc3 a600000.dwc3: Fifosize(3717) > RAM size(3462) ep3in depth:217973127
configfs-gadget gadget: u_audio_start_capture:521 Error!
dwc3 a600000.dwc3: request 000000000be13e18 was not queued to ep3in
Add another bit DWC3_EP_TXFIFO_RESIZED to dep->flags to keep track of
whether an EP had already been resized in the current configuration.
If so, bail out of dwc3_gadget_resize_tx_fifos() to avoid the
calculation error resulting from accumulating the EP's FIFO depth
repeatedly. This flag is retained across multiple ep_disable() and
ep_enable() calls and is cleared when GTXFIFOSIZn is reset in
dwc3_gadget_clear_tx_fifos() upon receiving the next Set Config.
Fixes: 9f607a309f ("usb: dwc3: Resize TX FIFOs to meet EP bursting requirements")
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20211021180129.27938-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since function drivers will still be active until dwc3_disconnect_gadget()
is called, some applications will continue to queue packets to DWC3
gadget. This can lead to a flood of messages regarding failed ep queue,
as the endpoint is in the process of being disabled. Change the log
level to debug, so that it can be enabled when debugging issues.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20211018192647.32121-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit c6e23b89a9 ("usb: dwc3: gadget: set gadgets parent to the right
controller") changed the device for the UDC and broke the user space scripts
that instantiate the USB gadget(s) via ConfigFS.
Revert it for now until the better solution will be proposed.
Fixes: c6e23b89a9 ("usb: dwc3: gadget: set gadgets parent to the right controller")
Tested-by: Ferry Toth <fntoth@gmail.com>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211004141839.49079-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race present where the DWC3 runtime resume runs in parallel
to the UDC unbind sequence. This will eventually lead to a possible
scenario where we are enabling the run/stop bit, without a valid
composition defined.
Thread#1 (handling UDC unbind):
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
--> continue UDC unbind sequence
-->Thread#2 is running in parallel here
Thread#2 (handing next cable connect)
__dwc3_set_mode()
-->pm_runtime_get_sync()
-->dwc3_gadget_resume()
-->dwc->gadget_driver is NOT NULL yet
-->dwc3_gadget_run_stop(1)
--> _dwc3gadget_start()
...
Fix this by tracking the pullup disable routine, and avoiding resuming
of the DWC3 gadget. Once the UDC is re-binded, that will trigger the
pullup enable routine, which would handle enabling the DWC3 gadget.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210917021852.2037-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After we start to do core soft reset while usb role switch,
the phy init is invoked at every switch to device mode, but
its counter part de-init is missing, this causes the actual
phy init can not be done when we really want to re-init phy
like system resume, because the counter maintained by phy
core is not 0. considering phy init is actually redundant for
role switch, so move out the phy init from core soft reset to
dwc3 core init where is the only place required.
Fixes: f88359e158 ("usb: dwc3: core: Do core softreset when switch mode")
Cc: <stable@vger.kernel.org>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Tested-by: John Stultz <john.stultz@linaro.org> #HiKey960
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1631068099-13559-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set reference clock period when it differs from dwc3 default hardware
set.
We could calculate clock period based on reference clock frequency. But
this information is not always available. This is the case of PCI bus
attached USB host. For that reason we use a custom property.
Tested (USB2 only) on IPQ6010 SoC based board with 24 MHz reference
clock while hardware default is 19.2 MHz.
[ baruch: rewrite commit message; drop GFLADJ code; remove 'quirk-' from
property name; mention tested hardware ]
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Balaji Prakash J <bjagadee@codeaurora.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Nacked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/9f399bdf1ff752e31ab7497e3d5ce19bbb3ff247.1630389452.git.baruch@tkos.co.il
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a number
of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9+Tw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymqyQCgxWjp4VD9Ycbz1XsHRIkkERWj6WgAnRe4mCpG
n5csYXATbYUD0UdH0hru
=xZCV
-----END PGP SIGNATURE-----
Merge tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a
number of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: isp1760: otg control register access
usb: isp1760: use the right irq status bit
usb: isp1760: write to status and address register
usb: isp1760: fix qtd fill length
usb: isp1760: fix memory pool initialization
usb: typec: tcpm: Fix spelling mistake "atleast" -> "at least"
usb: dwc2: Fix spelling mistake "was't" -> "wasn't"
usb: renesas_usbhs: Fix spelling mistake "faile" -> "failed"
usb: host: xhci-rcar: Don't reload firmware after the completion
usb: xhci-mtk: allow bandwidth table rollover
usb: mtu3: fix random remote wakeup
usb: mtu3: return successful suspend status
usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint
usb: xhci-mtk: modify the SOF/ITP interval for mt8195
usb: xhci-mtk: add a member of num_esit
usb: xhci-mtk: check boundary before check tt
usb: xhci-mtk: update fs bus bandwidth by bw_budget_table
usb: xhci-mtk: fix issue of out-of-bounds array access
usb: xhci-mtk: support option to disable usb2 ports
usb: xhci-mtk: fix use-after-free of mtk->hcd
...
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb01473648 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so")
Cc: <stable@vger.kernel.org>
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
Fixes: c4233573f6 ("usb: dwc3: gadget: prepare TRBs on update transfers too")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/e91e975affb0d0d02770686afc3a5b9eb84409f6.1629335416.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD's latest platforms has DWC3 controller. Add the PCI ID and
properties for the same.
Signed-off-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20210823184449.2796184-2-Nehal-Bakulchandra.shah@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IRQ occurs between calling devm_request_threaded_irq() and
initializing dwc3_imx->dwc3, then null pointer dereference occurs
since dwc3_imx->dwc3 is used in dwc3_imx8mp_interrupt().
The patch puts registration of the interrupt handler after
initializing of neccesery data.
Found by Linux Driver Verification project (linuxtesting.org).
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210819154818.18334-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On DWC_usb3 revisions 3.00a and newer (including DWC_usb31 and
DWC_usb32) the GUCTL1 register gained the DEV_DECOUPLE_L1L2_EVT
field (bit 31) which when enabled allows the controller in device
mode to treat USB 2.0 L1 LPM & L2 events separately.
After commit d1d90dd272 ("usb: dwc3: gadget: Enable suspend
events") the controller will now receive events (and therefore
interrupts) for every state change when entering/exiting either
L1 or L2 states. Since L1 is handled entirely by the hardware
and requires no software intervention, there is no need to even
enable these events and unnecessarily notify the gadget driver.
Enable the aforementioned bit to help reduce the overall interrupt
count for these L1 events that don't need to be handled while
retaining the events for full L2 suspend/wakeup.
Tested-by: Jun Li <jun.li@nxp.com>
Tested-by: Amit Pundir <amit.pundir@linaro.org> # for RB5 (sm8250)
Tested-by: John Stultz <john.stultz@linaro.org> # for HiKey960 & db845c
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210812082635.12924-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dwc3_qcom_acpi_register_core(), the driver neglects to check the result
of platform_get_irq()'s call and blithely assigns the negative error codes
to the allocated child device's IRQ resource and then passing this resource
to platform_device_add_resources() and later causing dwc3_otg_get_irq() to
fail anyway. Stop calling platform_device_add_resources() with the invalid
IRQ #s, so that there's less complexity in the IRQ error checking.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/45fec3da-1679-5bfe-5d74-219ca3fb28e7@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: f90db10779 ("usb: dwc3: meson-g12a: Add support for IRQ based OTG switching")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/96106462-5538-0b2f-f2ab-ee56e4853912@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Piyush Mehta
Krzysztof Kozlowski
Wesley Cheng
Kushagra Verma
William Wu
Greg Kroah-Hartman
Johan Hovold
Michael Grzeschik
Heikki Krogerus
Rohith Kollalsi
Yang Yingliang
Thinh Nguyen
Mauro Carvalho Chehab
Sandeep Maheswaram
Li Jun
Stephen Rothwell
Stephan Gerhold
Mayank Rana
Albert Wang
Piyush Mehta
Zheng Yongjun
Andrey Smirnov
Dan Vacura
Sven Peter
Peter Geis
Aswath Govindraju
Shruthi Sanil
H. Nikolaus Schaller
Bin Yang
Alexander Stein
Heiner Kallweit
Sebastian Andrzej Siewior
Hans de Goede
Udipto Goswami
Sean Anderson
Robert Hancock
Miaoqian Lin
Lad Prabhakar
Douglas Anderson
Fabio Aiuto
Amjad Ouled-Ameur
Jack Pham
Wesley Cheng
Andy Shevchenko
Krzysztof Kozlowski
Balaji Prakash J
Linus Torvalds
Nehal Bakulchandra Shah
Nadezda Lutovinova
Sergey Shtylyov