The Intel 82855PM host bridge / Mobility FireGL 9000 RV250 combination
in an (outdated) ThinkPad T41 needs AGPMode 1 for suspend/resume (under
KMS, that is). So add a quirk for it.
(Change R250 to RV250 in comment for preceding quirk too.)
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The save struct is not initialized previously so explicitly
mark the crtcs as not used when they are not in use.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
blkdev_issue_discard currently assumes that the granularity
is a power of 2. So in raid5, round the chosen number up to
avoid embarrassment.
Cc: Shaohua Li <shli@kernel.org>
Signed-off-by: NeilBrown <neilb@suse.de>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
md_stop() would stop an array, but not free various attached
data structures.
For internal arrays, these are freed later in do_md_stop() or
mddev_put(), but they don't apply for dm-raid arrays.
So get md_stop() to free them, and only all it from dm-raid.
For internal arrays we now call __md_stop.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If read_seqretry returned true and bbp was changed, it will write
invalid address which can cause some serious problem.
This bug was introduced by commit v3.0-rc7-130-g2699b67.
So fix is suitable for 3.0.y thru 3.6.y.
Reported-by: zhuwenfeng@kedacom.com
Tested-by: zhuwenfeng@kedacom.com
Cc: stable@vger.kernel.org
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This bug was introduced by commit(v3.0-rc7-126-g2230dfe).
So fix is suitable for 3.0.y thru 3.6.y.
Cc: stable@vger.kernel.org
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In target mode, sent sk_buff were not freed in pn533_tm_send_complete
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
cmd is allocated in pn533_dep_link_up and passed as an arg to
pn533_send_cmd_frame_async together with a complete cb.
arg is passed to the cb and must be kfreed there.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
cmd was freed in pn533_dep_link_up regardless of
pn533_send_cmd_frame_async return code. Cmd is passed as argument to
pn533_in_dep_link_up_complete callback and should be freed there.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In pn533_wq_cmd command was removed from list without cmd_lock held
(race with pn533_send_cmd_frame_async) which could lead to list
corruption. Delete command from list before releasing lock.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit "ath9k: improve suspend/resume reliability" broke ath9k_htc
and bringing up the device would hang indefinitely. Fix this.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store the requested gpios so that they can be freed on error/removal.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Commit 952cbaaa9b (OMAPFB: Change
dssdev->manager references) added checks for OMAPFB_WAITFORVSYNC ioctl
to verify that the display, output and overlay manager exist. However,
the code erroneously uses && for each part, which means that
OMAPFB_WAITFORVSYNC may crash the kernel if no display, output or
manager is associated with the framebuffer.
This patch fixes the issue by using ||.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When doing conversion to dynamic input numbers I inadvertently moved
/dev/input/mice from c,13,63 to c,13,31. We need to fix this so that
setups with statically populated /dev continue working.
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Leftover of 57d6d456cf ("sis900: stop
using net_device.{base_addr, irq} and convert to __iomem.").
It is needed for suspend / resume to work.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jan Janssen <medhefgo@web.de>
Cc: Daniele Venzano <venza@brownhat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
memcmp->nv_strncmp conversion, in addition to name change, should have
inverted the return value.
But nv_strncmp does not act like strncmp - it does not check for string
terminator, returns true/false instead of -1/0/1 and has different
parameters order.
Let's rename it to nv_memcmp and let it act like memcmp.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes a null pointer dereference when reclocking on my fermi.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some archs defconfigs have CONFIG_FRAME_WARN set to 1024, which lead to this
warning:
drivers/gpu/drm/nouveau/core/engine/graph/ctxnv40.c: warning: the frame size
of 1184 bytes is larger than 1024 bytes
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- Disable blinking on the Orion GPIO driver
- Two Kconfig-style fixes to avoid broken builds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UBlv
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull last minute GPIO fixes from Linus Walleij:
- Disable blinking on the Orion GPIO driver
- Two Kconfig-style fixes to avoid broken builds
* tag 'gpio-fixes-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio-mcp23s08: Build I2C support even when CONFIG_I2C=m
gpio: adnp: Depend on OF_GPIO instead of OF
mvebu-gpio: Disable blinking when enabling a GPIO for output
right. -rc6 beat me by ~2 hours it seems, and they really should have
gone out long before that.
These have been in libata-dev.git for a day or so (unfortunately
linux-next is on vacation). The main one is #1, with the others being
minor bits. #1 has multiple tested-by, and can be considered a
regression fix IMO.
1) Fix ACPI oops, https://bugzilla.kernel.org/show_bug.cgi?id=48211
2) Temporary WARN_ONCE() debugging patch for further ACPI debugging.
The code already oopses here, and so this merely gives slightly
better info. Related to https://bugzilla.kernel.org/show_bug.cgi?id=49151
which has been bisected down to a patch that _exposes_ a latest bug,
but said bisection target does not actually appear to be the root cause
itself.
3) sata_svw: fix longstanding error recovery bug, which was
preventing kdump, by adding missing DMA-start bit check. Core
code was already checking DMA-start, but ancillary, less-used
routines were not. Fixed.
4) sata_highbank: fix minor __init/__devinit warning
5) Fix minor warning, if CONFIG_PM is set, but CONFIG_PM_SLEEP is not set
6) pata_arasan: proper functioning requires clock setting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=V0y8
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
"If you were going to shoot me for not sending these earlier, you would
be right. -rc6 beat me by ~2 hours it seems, and they really should
have gone out long before that.
These have been in libata-dev.git for a day or so (unfortunately
linux-next is on vacation). The main one is #1, with the others being
minor bits. #1 has multiple tested-by, and can be considered a
regression fix IMO.
1) Fix ACPI oops:
https://bugzilla.kernel.org/show_bug.cgi?id=48211
2) Temporary WARN_ONCE() debugging patch for further ACPI debugging.
The code already oopses here, and so this merely gives slightly
better info. Related to
https://bugzilla.kernel.org/show_bug.cgi?id=49151
which has been bisected down to a patch that _exposes_ a latest
bug, but said bisection target does not actually appear to be the
root cause itself.
3) sata_svw: fix longstanding error recovery bug, which was
preventing kdump, by adding missing DMA-start bit check. Core
code was already checking DMA-start, but ancillary, less-used
routines were not. Fixed.
4) sata_highbank: fix minor __init/__devinit warning
5) Fix minor warning, if CONFIG_PM is set, but CONFIG_PM_SLEEP is not
set
6) pata_arasan: proper functioning requires clock setting"
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] PM callbacks should be conditionally compiled on CONFIG_PM_SLEEP
sata_svw: check DMA start bit before reset
libata debugging: Warn when unable to find timing descriptor based on xfer_mode
sata_highbank: mark ahci_highbank_probe as __devinit
pata_arasan: Initialize cf clock to 166MHz
libata-acpi: Fix NULL ptr derference in ata_acpi_dev_handle
This can happen when we shut down suddenly an interface.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver has both SPI and I2C pieces. The appropriate pieces are built based
on whether SPI and/or I2C is/are enabled. However, it was only checking if I2C
was built-in, never if it was built as a module. This patch checks for either
since building both this driver and I2C as modules is possible.
Signed-off-by: Daniel M. Weeks <dan@danweeks.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver accesses the of_node field of struct gpio_chip, which is only
available if OF_GPIO is selected. This solves a build issue on SPARC
which conflicts with OF_GPIO and therefore does not provide this field.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The plat-orion GPIO driver would disable any pin blinking whenever
using a pin for output. Do the same here, as a blinking LED will
continue to blink regardless of what the GPIO pin level is.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can't assume this device exists, fall back to the bridge itself.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Matthew Thode <prometheanfire@gentoo.org>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (12 patches)
revert "mm: fix-up zone present pages"
tmpfs: change final i_blocks BUG to WARNING
tmpfs: fix shmem_getpage_gfp() VM_BUG_ON
mm: highmem: don't treat PKMAP_ADDR(LAST_PKMAP) as a highmem address
mm: revert "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures"
rapidio: fix kernel-doc warnings
swapfile: fix name leak in swapoff
memcg: fix hotplugged memory zone oops
mips, arc: fix build failure
memcg: oom: fix totalpages calculation for memory.swappiness==0
mm: fix build warning for uninitialized value
mm: add anon_vma_lock to validate_mm()
Fix rapidio kernel-doc warnings:
Warning(drivers/rapidio/rio.c:415): No description found for parameter 'local'
Warning(drivers/rapidio/rio.c:415): Excess function parameter 'lstart' description in 'rio_map_inb_region'
Warning(include/linux/rio.h:290): No description found for parameter 'switches'
Warning(include/linux/rio.h:290): No description found for parameter 'destid_table'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) tx_filtered/ps_tx_buf queues need to be accessed with the SKB queue
lock, from Arik Nemtsov.
2) Don't call 802.11 driver's filter configure method until it's
actually open, from Felix Fietkau.
3) Use ieee80211_free_txskb otherwise we leak control information.
From Johannes Berg.
4) Fix memory leak in bluetooth UUID removal,f rom Johan Hedberg.
5) The shift mask trick doesn't work properly when 'optname' is out of
range in do_ip_setsockopt(). Use a straightforward switch statement
instead, the compiler emits essentially the same code but without
the missing range check. From Xi Wang.
6) Fix when we call tcp_replace_ts_recent() otherwise we can
erroneously accept a too-high tsval. From Eric Dumazet.
7) VXLAN bug fixes, mostly to do with VLAN header length handling, from
Alexander Duyck.
8) Missing return value initialization for IPV6_MINHOPCOUNT socket
option handling. From Hannes Frederic.
9) Fix regression in tasklet handling in jme/ksz884x/xilinx drivers,
from Xiaotian Feng.
10) At smsc911x driver init time, we don't know if the chip is in word
swap mode or not. However we do need to wait for the control
register's ready bit to be set before we program any other part of
the chip. Adjust the wait loop to account for this. From Kamlakant
Patel.
11) Revert erroneous MDIO bus unregister change to mdio-bitbang.c
12) Fix memory leak in /proc/net/sctp/, from Tommi Rantala.
13) tilegx driver registers IRQ with NULL name, oops, from Simon Marchi.
14) TCP metrics hash table kzalloc() based allocation can fail, back
down to using vmalloc() if it does. From Eric Dumazet.
15) Fix packet steering out-of-order delivery regression, from Tom
Herbert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
net-rps: Fix brokeness causing OOO packets
tcp: handle tcp_net_metrics_init() order-5 memory allocation failures
batman-adv: process broadcast packets in BLA earlier
batman-adv: don't add TEMP clients belonging to other backbone nodes
batman-adv: correctly pass the client flag on tt_response
batman-adv: fix tt_global_entries flags update
tilegx: request_irq with a non-null device name
net: correct check in dev_addr_del()
tcp: fix retransmission in repair mode
sctp: fix /proc/net/sctp/ memory leak
Revert "drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free"
net/smsc911x: Fix ready check in cases where WORD_SWAP is needed
drivers/net: fix tasklet misuse issue
ipv4/ip_vti.c: VTI fix post-decryption forwarding
brcmfmac: fix typo in CONFIG_BRCMISCAN
vxlan: Update hard_header_len based on lowerdev when instantiating VXLAN
vxlan: fix a typo.
ipv6: setsockopt(IPIPPROTO_IPV6, IPV6_MINHOPCOUNT) forgot to set return value
doc/net: Fix typo in netdev-features.txt
vxlan: Fix error that was resulting in VXLAN MTU size being 10 bytes too large
...
When host_sleep_config command fails we should return error to
MMC core to indicate the failure for our device.
The misspelled variable is also removed as it's redundant.
Cc: "3.0+" <stable@vger.kernel.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported by Tim Shepard:
I was seeing sporadic failures (wedgeups), and the majority of those
failures I saw printed the printouts in mwifiex_cmd_timeout_func with
cmd = 0xe5 which is CMD_802_11_HS_CFG_ENH. When this happens, two
minutes later I get notified that the rtcwake thread is blocked, like
this:
INFO: task rtcwake:3495 blocked for more than 120 seconds.
To get the hung thread unblocked we wake up the cmd wait queue and
cancel the ioctl.
Cc: "3.4+" <stable@vger.kernel.org>
Reported-by: Tim Shepard <shep@laptop.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an ISY IWL 2000. Probably a clone of Belkin F7D1102 050d:1102.
Its FCC ID is the same.
Signed-off-by: Albert Pool <albertpool@solcon.nl>
Cc: stable@vger.kernel.org
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've been sitting on this longer than we meant to due to travel and
other activities, but the number of patches is luckily not that high.
Biggest changes are from a batch of OMAP bugfixes, but there are a
few for the broader set of SoCs too (bcm2835, pxa, highbank, tegra,
at91 and i.MX).
The OMAP patches contain some fixes for MUSB/PHY on omap4 which
ends up being a bit on the large side but needed for legacy (non-DT)
platforms. Beyond that there are a handful of hwmod/pm changes.
So, fairly noncontroversial stuff all in all, and as usual around this
time the fixes are well targeted at specific problems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aKWl
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on this longer than we meant to due to travel and
other activities, but the number of patches is luckily not that high.
Biggest changes are from a batch of OMAP bugfixes, but there are a few
for the broader set of SoCs too (bcm2835, pxa, highbank, tegra, at91
and i.MX).
The OMAP patches contain some fixes for MUSB/PHY on omap4 which ends
up being a bit on the large side but needed for legacy (non-DT)
platforms. Beyond that there are a handful of hwmod/pm changes.
So, fairly noncontroversial stuff all in all, and as usual around this
time the fixes are well targeted at specific problems."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: ehci: fix host power mask bit
ARM i.MX: fix error-valued pointer dereference in clk_register_gate2()
ARM: at91/usbh: fix overcurrent gpio setup
ARM: at91/AT91SAM9G45: fix crypto peripherals irq issue due to sparse irq support
ARM: boot: Fix usage of kecho
ARM: OMAP: ocp2scp: create omap device for ocp2scp
ARM: OMAP4: add _dev_attr_ to ocp2scp for representing usb_phy
drivers: bus: ocp2scp: add pdata support
irqchip: irq-bcm2835: Add terminating entry for of_device_id table
ARM: highbank: retry wfi on reset request
ARM: OMAP4: PM: fix regulator name for VDD_MPU
ARM: OMAP4: hwmod data: do not enable or reset the McPDM during kernel init
ARM: OMAP2+: hwmod: add flag to prevent hwmod code from touching IP block during init
ARM: dt: tegra: fix length of pad control and mux registers
ARM: OMAP: hwmod: wait for sysreset complete after enabling hwmod
ARM: OMAP2+: clockdomain: Fix OMAP4 ISS clk domain to support only SWSUP
ARM: pxa/spitz_pm: Fix hang when resuming from STR
ARM: pxa: hx4700: Fix backlight PWM device number
ARM: OMAP2+: PM: add missing newline to VC warning message
Pull HID fix from Jiri Kosina:
"This has a build fix for architectures where memcmp() is macro, from
Jiri Slaby"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: microsoft: do not use compound literal - fix build
Here are some USB fixes for the 3.7 tree.
Nothing huge here, just a number of tiny bugfixes resolving issues that
have been found, and two reverts of patches that were found to have
caused problems.
All of these have been in linux-next already.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCmRoUACgkQMUfUDdst+ynwAACg2if9XANSq4+GqdR7lSF5jCRO
hwMAoNh7XAM4GEXPB9m3rB395p9rHsN0
=31VS
-----END PGP SIGNATURE-----
Merge tag 'usb-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some USB fixes for the 3.7 tree.
Nothing huge here, just a number of tiny bugfixes resolving issues
that have been found, and two reverts of patches that were found to
have caused problems.
All of these have been in linux-next already.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "USB/host: Cleanup unneccessary irq disable code"
USB: option: add Alcatel X220/X500D USB IDs
USB: option: add Novatel E362 and Dell Wireless 5800 USB IDs
USB: keyspan: fix typo causing GPF on open
USB: fix build with XEN and EARLY_PRINTK_DBGP enabled but USB_SUPPORT disabled
USB: usb_wwan: fix bulk-urb allocation
usb: otg: Fix build errors if USB_MUSB_OMAP2PLUS is selected as module
usb: musb: ux500: fix 'musbid' undeclared error in ux500_remove()
Revert "usb: musb: use DMA mode 1 whenever possible"
Here are two TTY driver fixes for 3.7-rc5.
They resolve a bug in the hvc driver that has been reported, and fix a
problem with the list of device ids in the max310x serial driver.
Both have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCmRekACgkQMUfUDdst+ym94QCfZXb34WBxejNff2PowH9GZ7zL
NNAAoLi2YFB68la0KYxQ8zWBakL/QeyZ
=w8fs
-----END PGP SIGNATURE-----
Merge tag 'tty-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fixes from Greg Kroah-Hartman:
"Here are two TTY driver fixes for 3.7-rc5.
They resolve a bug in the hvc driver that has been reported, and fix a
problem with the list of device ids in the max310x serial driver.
Both have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: max310x: Add terminating entry for spi_device_id table
TTY: hvc_console, fix port reference count going to zero prematurely
Here is a single patch, a revert of an android driver patch, that
resolves a bug that has been reported in the Android alarm driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCmRx4ACgkQMUfUDdst+yl3DwCbB9ekMEOeU8kRPiFozI8m702t
JbsAnikKlAk+EmoufP46+3+PVKh7582d
=pRqt
-----END PGP SIGNATURE-----
Merge tag 'staging-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fix from Greg Kroah-Hartman:
"Here is a single patch, a revert of an android driver patch, that
resolves a bug that has been reported in the Android alarm driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: Android alarm: IOCTL command encoding fix"
Pull s390 patches from Martin Schwidefsky:
"Some more bug fixes and a config change.
The signal bug is nasty, if the clock_gettime vdso function is
interrupted by a signal while in access-register-mode we end up with
an endless signal loop until the signal stack is full. The config
change is for aligned struct pages, gives us 8% improvement with
hackbench."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/3215: fix tty close handling
s390/mm: have 16 byte aligned struct pages
s390/gup: fix access_ok() usage in __get_user_pages_fast()
s390/gup: add missing TASK_SIZE check to get_user_pages_fast()
s390/topology: fix core id vs physical package id mix-up
s390/signal: set correct address space control
Pull drm fixes from Dave Airlie:
"All pretty normal: one TTM oops fix, one radeon, a few intel and a
vmwgfx fix."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: remove unneeded preempt_disable/enable
ttm: Clear the ttm page allocated from high memory zone correctly
vmwgfx: return an -EFAULT if copy_to_user() fails
drm/radeon: fix logic error in atombios_encoders.c
drm/i915: do not ignore eDP bpc settings from vbt
drm/i915/sdvo: clean up connectors on intel_sdvo_init() failures
drm/i915/crt: fix DPMS standby and suspend mode handling
This patch simply makes the tilegx net driver call request_irq with a
non-null name. It makes the output in /proc/interrupts more obvious, but
also helps tools that don't expect to find null there.
Signed-off-by: Simon Marchi <simon.marchi@polymtl.ca>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will fix warnings like following when CONFIG_PM_SLEEP is not set:
warning: 'xxx_suspend' defined but not used [-Wunused-function]
warning: 'xxx_resume' defined but not used [-Wunused-function]
Because
SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If kdump is triggered with pending IO, controller may not respond causing
kdump to fail.
http://marc.info/?l=linux-ide&m=133032255424658&w=2
During error recovery ata_do_dev_read_id never completes due hang
in mmio_insw.
ata_do_dev_read_id
ata_sff_data_xfer
ioread16_rep
mmio_insw
if DMA start bit is cleared before reset, PIO command is successful
and kdump succeeds.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_timing_find_mode could return NULL which is not checked by all
low-level ATA drivers using it and cause a NULL ptr deref. Warn at least
so that possible issues can get fixed easily.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ahci_highbank_probe function is incorrectly marked as __init,
which means it can get discarded at boot time, which might be
a problem if for some reason the device only becomes operational
after loading another module.
Using __devinit instead avoids seeing this warning for every build:
WARNING: vmlinux.o(.data+0xf7b0): Section mismatch in reference from the
variable ahci_highbank_driver to the function .init.text:ahci_highbank_probe()
The variable ahci_highbank_driver references
the function __init ahci_highbank_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PATA arasan driver expects the clock to be set to 166 MHz for proper
functioning. This patch sets clk to 166 MHz in probe.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit 6b66d95895 didn't handle SATA PMP
case in ata_acpi_bind_device and will cause a NULL ptr dereference when
user attached a SATA drive to the PMP port. Fix this by checking PMP
support.
This bug is reported by Dan van der Ster in the following bugzilla page:
https://bugzilla.kernel.org/show_bug.cgi?id=48211
Reported-by: Dan van der Ster <dan@vanderster.com>
Tested-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tested-by: Simon <tangouniform@sbcglobal.net>
Daniel writes:
Just a few small things to fix regressions, somehow all patches from Jani:
- Fix dpms confusion about which platforms support intermediate modes on
vga.
- Revert the "ignore vbt for eDP bpc" patch, it breaks machines. This will
annoy mbp retina owners again, but windows machines seem to _really_
depend upon this. We can try to quirk the mbp retinas again in 3.8 and
backport the patch.
- Fix connector leaks when the sdvo setup failed, resulted in an OOPS
later on when trying to probe that connector (with it's encoder kfree'd
already).
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: do not ignore eDP bpc settings from vbt
drm/i915/sdvo: clean up connectors on intel_sdvo_init() failures
drm/i915/crt: fix DPMS standby and suspend mode handling
It is unnecessary to disable preemption explicitly while calling
copy_highpage(). Because copy_highpage() will do it again through
kmap_atomic/kunmap_atomic.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The TTM page can be allocated from high memory. In such case it is
wrong to use the page_address(page) as the virtual address for the high memory
page.
bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=50241
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
copy_to_user() returns the number of bytes remaining to be copied, but
we want to return a negative error code here. I fixed a couple of these
last year, but I missed this one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pill i2c fixes from Jean Delvare.
Well, "fixes".. The biggest patch here is actually Jan marking Wolfram
Sang as the main i2c subsystem maintainer, with Jan staying on as the PC
controller maintainer.
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-mux-pinctrl: Fix probe error path
MAINTAINERS: i2c: 7 years, this is it
A few fixes for teardown issues that will be rarely seen, plus a fix for
a silly bug in regulator_is_supported_voltage() which shows how often
the answer to the question should be false.
The supported voltage commit is very new as I just edited to add a Cc to
stable, the code itself has been in -next.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HyTz
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few fixes for teardown issues that will be rarely seen, plus a fix
for a silly bug in regulator_is_supported_voltage() which shows how
often the answer to the question should be false.
The supported voltage commit is very new as I just edited to add a Cc
to stable, the code itself has been in -next."
* tag 'regulator-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fix voltage check in regulator_is_supported_voltage()
regulator: core: Avoid deadlock when regulator_register fails
Regulator: core: Unregister when gpio request fails.
The 3215 console always has the RAW3215_FIXED flag set, which causes
raw3215_shutdown() not to wait for outstanding I/O requests if an attached
tty gets closed.
The flag however can be simply removed, so we can guarantee that all requests
belonging to the tty have been processed when the tty is closed.
However the tasklet that belongs to the 3215 device may be scheduled even if
there is no tty attached anymore, since we have a race between console and tty
processing.
Thefore unconditional tty_wakekup() in raw3215_wakeup() can cause the following
NULL pointer dereference:
3.465368 Unable to handle kernel pointer dereference at virtual kernel address (null)
3.465448 Oops: 0004 #1 SMP
3.465454 Modules linked in:
3.465459 CPU: 1 Not tainted 3.6.0 #1
3.465462 Process swapper/1 (pid: 0, task: 000000003ffa4428, ksp: 000000003ffb7ce0)
3.465466 Krnl PSW : 0404100180000000 0000000000162f86 (__wake_up+0x46/0xb8)
3.465480 R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:0 CC:1 PM:0 EA:3
Krnl GPRS: fffffffffffffffe 0000000000000000 0000000000000160 0000000000000001
3.465492 0000000000000001 0000000000000004 0000000000000004 000000000096b490
3.465499 0000000000000001 0000000000000100 0000000000000001 0000000000000001
3.465506 070000003fc87d60 0000000000000160 000000003fc87d68 000000003fc87d00
3.465526 Krnl Code: 0000000000162f76: e3c0f0a80004 lg %r12,168(%r15)
0000000000162f7c: 58000370 l %r0,880
#0000000000162f80: c007ffffffff00 xilf %r0,4294967295
>0000000000162f86: ba102000 cs %r1,%r0,0(%r2)
0000000000162f8a: 1211 ltr %r1,%r1
0000000000162f8c: a774002f brc 7,162fea
0000000000162f90: b904002d lgr %r2,%r13
0000000000162f94: b904003a lgr %r3,%r10
3.465597 Call Trace:
3.465599 (<0400000000000000> 0x400000000000000)
3.465602 <000000000048c77e> raw3215_wakeup+0x2e/0x40
3.465607 <0000000000134d66> tasklet_action+0x96/0x168
3.465612 <000000000013423c> __do_softirq+0xd8/0x21c
3.465615 <0000000000134678> irq_exit+0xa8/0xac
3.465617 <000000000046c232> do_IRQ+0x182/0x248
3.465621 <00000000005c8296> io_return+0x0/0x8
3.465625 <00000000005c7cac> vtime_stop_cpu+0x4c/0xb8
3.465629 (<0000000000194e06> tick_nohz_idle_enter+0x4e/0x74)
3.465633 <0000000000104760> cpu_idle+0x170/0x184
3.465636 <00000000005b5182> smp_start_secondary+0xd6/0xe0
3.465641 <00000000005c86be> restart_int_handler+0x56/0x6c
3.465643 <0000000000000000> 0x0
3.465645 Last Breaking-Event-Address:
3.465647 <0000000000403136> tty_wakeup+0x46/0x98
3.465652
3.465654 Kernel panic - not syncing: Fatal exception in interrupt
01: HCPGIR450W CP entered; disabled wait PSW 00020001 80000000 00000000 0010F63C
The easiest solution is simply to check if tty is NULL in the tasklet.
If it is NULL nothing is to do (no tty attached), otherwise tty_wakeup()
can be called, since we hold a reference to the tty.
This is not nice... but it is a small patch and it works.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch fixes errors seen in identifying old Samsung SLC, due to the
following commits:
commit e2d3a35ee4
mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID
commit e3b88bd604
mtd: nand: add generic READ ID length calculation functions
Some Samsung NAND with "5-byte" ID really appear to have 6-byte IDs, with
wraparound like:
Samsung K9K8G08U0D
ec d3 51 95 58 ec ec d3
Samsung K9F1G08U0C
ec f1 00 95 40 ec ec f1
Samsung K9F2G08U0B
ec da 10 95 44 00 ec da
This bad wraparound makes it hard to reliably detect the difference
between Samsung SLC with 5-byte ID and Samsung SLC with 6-byte ID.
The fix is to, for now, only use the new Samsung table for MLC. We
cannot support the new SLC (K9FAG08U0M) until Samsung gives better ID
decode information.
Note that this applies in addition to the previous regression fix:
commit bc86cf7af2
mtd: nand: fix Samsung SLC NAND identification regression
Together, these patches completely restore the previous detection
behavior so that we cannot see any more regressions in Samsung SLC NAND
(finger crossed). With luck, I can get a hold of a Samsung
representative and stop having to cross my fingers eventually.
Reported-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
A combination of the following two commits caused a regression in 3.7-rc1
when identifying some Samsung NAND, so that some previously working NAND
were no longer detected properly:
commit e3b88bd604
mtd: nand: add generic READ ID length calculation functions
commit e2d3a35ee4
mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID
Particularly, a regression was seen on Samsung K9F2G08U0B, with the
following full 8-byte READ ID string:
ec da 10 95 44 00 ec da
The basic problem is that Samsung manufactures both SLC and MLC NAND
that use a non-standard decoding table for deriving information from
their IDs. I have heuristically determined that all the chips that use
the new table have ID strings which wrap around after the 6th byte.
Unfortunately, I overlooked the fact that some older Samsung SLC (which
use a different decoding table) have "5 byte ID strings" which also wrap
around after the 6th byte.
This patch re-introduces a distinction between these old and new Samsung
NAND by checking that the 6th byte is non-zero, allowing both old and
new Samsung NAND to be detected properly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The main samsung pinctrl module references the specific exynos4210
pinctrl driver, which selects the main driver in Kconfig.
Making the main driver a silent "bool" option avoid this potential
build error if CONFIG_PINCTRL_SAMSUNG=y && CONFIG_PINCTRL_EXYNOS4=n:
drivers/built-in.o:(.rodata+0x4e4): undefined reference to `exynos4210_pin_ctrl'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit aa731872f7.
As pointed out by Ben Hutchings, this change is not correct.
mdiobus_unregister() can't be called if the bus isn't registered yet,
however this change can result in situations which cause that to
happen.
Part of the confusion here revolves around the fact that the
callers of this module control registration/unregistration,
rather than the module itself.
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip ready check added by the commit 3ac3546e [Always wait for
the chip to be ready] does not work when the register read/write
is word swapped. This check has been added before the WORD_SWAP
register is programmed, so we need to check for swapped register
value as well.
Bit 16 is marked as RESERVED in SMSC datasheet, Steve Glendinning
<steve@shawell.net> checked with SMSC and wrote:
The chip architects have concluded we should be reading PMT_CTRL
until we see any of bits 0, 8, 16 or 24 set. Then we should read
BYTE_TEST to check the byte order is correct (as we already do).
The rationale behind this is that some of the chip variants have
word order swapping features too, so the READY bit could actually
be in any of the 4 possible locations. The architects have confirmed
that if any of these 4 positions is set the chip is ready. The other
3 locations will either never be set or can only go high after READY
does (so also indicate the device is ready).
This change will check for the READY bit at the 16th position. We do
not check the other two cases (bit 8 and 24) since the driver does not
support byte-swapped register read/write.
Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 175c0dff, drivers uses tasklet_kill to avoid put disabled tasklet
on the tasklet vec. But some of the drivers uses tasklet_init & tasklet_disable
in the driver init code, then tasklet_enable when it is opened. This makes
tasklet_enable on a killed tasklet and make ksoftirqd crazy then. Normally,
drivers should use tasklet_init/tasklet_kill on device open/remove, and use
tasklet_disable/tasklet_enable on device suspend/resume.
Reported-by: Peter Wu <lekensteyn@gmail.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
regulator_is_supported_voltage() should return true only if the voltage
of fixed/constant regulator is between min_uV and max_uV.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The spi_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bdb498c200 "TTY: hvc_console, add tty install" took the port
refcounting out of hvc_open()/hvc_close(), but failed to remove the
kref_put() and tty_kref_put() calls in hvc_hangup() that were there to
remove the extra references that hvc_open() had taken.
The result was that doing a vhangup() when the current terminal was
a hvc_console, then closing the current terminal, would end up calling
destroy_hvc_struct() and making the port disappear entirely. This
meant that Fedora 17 systems would boot up but then not display the
login prompt on the console, and attempts to open /dev/hvc0 would
give a "No such device" error.
This fixes it by removing the extra kref_put() and tty_kref_put() calls.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old ifdef CONFIG_BRCMFISCAN looks wrong to me and it makes more
sense when CONFIG_BRCMISCAN is used.
This patch was just compile tested by me, but not runtime tested.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.
This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.
After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.
This patch has been tested with pandaboard for a few
iterations of the script mentioned above.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
When the firmware is in SNIFFER mode, it leaves
the FCS at the end of frame. Not telling mac80211
means it won't add the right flag to the radiotap
header and that confuses wireshark.
Since mac80211 doesn't have a per-packet flag, set
the HW flag dynamically. This works as the monitor
vif can only be present in the driver by itself.
This fixes a regression introduced by my
commit 5789772641
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri May 11 10:53:18 2012 +0200
iwlwifi: support explicit monitor interface
Cc: stable@vger.kernel.org [3.5+]
Reported-by: MARK PHILLIPS <mark.phillips@virgin.net>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When regulator_register fails and exits through the scrub path the
regulator_put function was called whilst holding the
regulator_list_mutex, causing deadlock.
This patch adds a private version of the regulator_put function which
can be safely called whilst holding the mutex, replacing the
aforementioned call.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver claims to support SMBus quick command but it was not the
case. This patch fixes this issue. Without it, i2cdetect finds imaginary
devices. And with some IP versions, trying to send 0 byte can cause
issue when writing data to an EEPROM.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[wsa: improved the commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.
- We set the default maximum to 0xFFFF because there are several
devices out there that only support two-byte block counts even with
WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
LIMITS VPD.
- max_write_same_blocks can be overriden per-device basis in sysfs.
- The UNMAP discovery heuristics remain unchanged but the discard
limits are tweaked to match the "real" WRITE SAME commands.
- In the error handling logic we now distinguish between WRITE SAME
with and without UNMAP set.
The discovery process heuristics are:
- If the device reports a SCSI level of SPC-3 or greater we'll issue
READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
supported. If that's the case we will use it.
- If the device supports the block limits VPD and reports a MAXIMUM
WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).
- Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
0xFFFFFFFF or the block count exceeds 0xFFFF.
- no_write_same is set for ATA, FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Support requests with more than one bio payload for discards. The total
number of bytes to be discarded is stored in req->__data_len and used in
sd_done() to complete the I/O.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The REPORT SUPPORTED OPERATION CODES command can be used to query
whether a given opcode is supported by a device. Add a helper function
that allows us to look up commands.
We only issue RSOC if the device reports compliance with SPC-3 or
later. But to err on the side of caution we disable the command for ATA,
FireWire and USB.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the event of a VXLAN device being linked to a device that has a
hard_header_len greater than that of standard ethernet we could end up with
the hard_header_len not being large enough for outgoing frames. In order to
prevent this we should update the length when a lowerdev is provided.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eXtensible and not eXtensiable in the comment on top.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating the memory for i2c busses, the code checked the wrong
variable and thus never detected if there was a memory error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit 6bd4a5d96c changed the
ANDROID_ALARM_GET_TIME ioctls from IOW to IOR. While technically
correct, the _IOC_DIR bits are ignored by alarm_ioctl, so the
commit breaks a userspace ABI used by all existing Android devices
for a purely cosmetic reason. Revert it.
Cc: stable <stable@vger.kernel.org>
Cc: Dae S. Kim <dae@velatum.com>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change fixes an issue I found where VXLAN frames were fragmented when
they were up to the VXLAN MTU size. I root caused the issue to the fact that
the headroom was 4 + 20 + 8 + 8. This math doesn't appear to be correct
because we are not inserting a VLAN header, but instead a 2nd Ethernet header.
As such the math for the overhead should be 20 + 8 + 8 + 14 to account for the
extra headers that are inserted for VXLAN.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of Huawei 3G and LTE modems implement a CDC NCM function,
including the necessary functional descriptors, but using a non
standard interface layout and class/subclass/protocol codes.
These devices can be handled by this driver with only a minor
change to the probing logic, allowing a single combined control
and data interface. This works because the devices
- include a CDC Union descriptor labelling the combined
interface as both master and slave, and
- have an alternate setting #1 for the bulk endpoints on the
combined interface.
The 3G/LTE network connection is managed by vendor specific AT
commands on a serial function in the same composite device.
Handling the managment function is out of the scope of this
driver. It will be handled by an appropriate USB serial
driver.
Reported-and-Tested-by: Olof Ermis <olof.ermis@gmail.com>
Reported-and-Tested-by: Tommy Cheng <tommy7765@yahoo.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the set_mac_address() function of qeth is invoked, qeth deletes
the old mac address first on OSA. Only if deletion returns
successfully the new mac address is set on OSA. Deletion may return
with a return value "MAC not found on OSA". In this case qeth
should continue setting the new mac address.
When the OSA cable is pulled, OSA forgets any set mac address. If
the OSA network interface acts as a slave to a bonding master
interface, bonding can invoke the set_mac_address function for
failover purposes and depends on successful setting of the new mac
address even though the old mac address could no longer be deleted.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return codes of IPA_CMD_QIPASSIST are not checked, especially the ones which
indicate that the command is not supported. As a result, the device driver
would not enable all available features on older card generations.
This patch adds proper checking and sets the bare minimum in the supported
functions flags to avoid follow-on errors.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device datasheet specifies the BUSY bit must be set when reading
or writing phy registers. This patch ensures we do that.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 73d4066055.
Martin Steigerwald reported that this change caused a hard lockup when
using USB if threadirqs are enabled. Thomas pointed out that this patch
is incorrect, and can cause problems. So revert it to get the
previously working functionality back.
Reported-by: Martin Steigerwald <Martin@lichtvoll.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chuansheng Liu <chuansheng.liu@intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell 5800 appears to be a simple rebrand of the Novatel E362.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f79b2d0f (USB: keyspan: fix NULL-pointer dereferences and
memory leaks) had a small typo which made the driver use wrong
offsets when mapping serial port private data. This results in
in a GPF when the port is opened.
Reported-by: Richard <richjunk@pacbell.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SATA MICROCODE DOWNALOAD fails on isci driver. After receiving Register
Device to Host (FIS 0x34) frame Initiator resets phy.
In the frame handler routine response (FIS 0x34) was copied into wrong
buffer and upper layer did not receive any answer which resulted in
timeout and reset.
This patch corrects this bug.
Signed-off-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There are laptops out there that need the eDP bpc from VBT. This is
effectively a revert of
commit 4344b813f1
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Aug 10 11:10:20 2012 +0200
drm/i915: ignore eDP bpc settings from vbt
but putting the VBT check after the EDID check to see them both in dmesg if
this clamps more than the EDID. We have enough history with bpc clamping to
warrant the extra debug info.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47641
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56401
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This pull request contains those missing clkdev entries which are needed
to boot that platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=VC2a
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull ux500 clk fixes from Mike Turquette:
"Missing clkdev entries are causing regressions on the U8500 platform.
This pull request contains those missing clkdev entries which are
needed to boot that platform."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: ux500: Register slimbus clock lookups for u8500
clk: ux500: Update rtc clock lookup for u8500
clk: ux500: Register msp clock lookups for u8500
clk: ux500: Register ssp clock lookups for u8500
clk: ux500: Register i2c clock lookups for u8500
Any failures in intel_sdvo_init() after the intel_sdvo_setup_output() call
left behind ghost connectors, attached (with a dangling pointer) to the
sdvo that has been cleaned up and freed. Properly destroy any connectors
attached to the encoder.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46381
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Tested-by: bjo@nord-west.org
[danvet: added a comment to explain why we need to clean up connectors
even when sdvo_output_setup fails.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the same time the prcc bit for the kclk is corrected to
bit 8 instead of 3.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Paul Bolle
Alex Deucher
NeilBrown
Srinivas Kandagatla
majianpeng
Thierry Escande
Waldemar Rymarkiewicz
Szymon Janc
John W. Linville
Sujith Manoharan
Abhilash Kesavan
Tushar Behera
Dmitry Torokhov
Francois Romieu
Marcin Slusarz
Maarten Lankhorst
Kelly Doran
Linus Torvalds
Emmanuel Grumbach
Daniel M. Weeks
Thierry Reding
Jamie Lentin
Alex Williamson
Cyril Roelandt
Randy Dunlap
Bing Zhao
Albert Pool
Arnd Bergmann
Simon Marchi
Yuanhan Liu
David Milburn
Borislav Petkov
Vipul Kumar Samar
Aaron Lu
Dave Airlie
Akinobu Mita
Zhao Yakui
Dan Carpenter
Heiko Carstens
Brian Norris
David S. Miller
Kamlakant Patel
Xiaotian Feng
Mark Brown
Marek Szyprowski
Axel Lin
Paul Mackerras
Hauke Mehrtens
Felipe Balbi
Paul Walmsley
Johannes Berg
Charles Keepax
Ludovic Desroches
Martin K. Petersen
Alexander Duyck
Rami Rosen
Guenter Roeck
Colin Cross
Bjørn Mork
Ursula Braun
Stefan Raspl
Steve Glendinning
Greg Kroah-Hartman
Dan Williams
Maciej Patelczyk
Jani Nikula
Ulf Hansson