This patch updates the clock tree with all the
changes in OMAP4430 ES2.
clock nodes added
-1- tie_low_clock_ck
-2- abe_dpll_bypass_clk_mux_ck
clock nodes deleted
-1- dpll_sys_ref_clk
-2- per_sgx_fclk
-3- usbphyocp2scp_ick
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: added comment re ES1 clocks to top of file]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
update OMAP Kconfig help texts for all supported SoC models
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This 'legacy' OMAP2420 McBSP2 muxing code is currently broken after recent
conversion to new mux code. The omap_mcbsp_request calling this code is
usually called after booting whereas the omap_mux_init_signal is __init
marked so null pointer dereference would occur.
Fix this by removing the muxing code and let the bootloader or board file to
do it if necessary. Remove also omap2_mcbsp_ops as there is no use for it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP SRG (Sample Rate Generator) and FSG (Frame Sync
Generator) is only needed to be enabled, when McBSP
is master.
In McBSP slave mode, the SRG, and FSG can be kept disabled,
which might save some power at the end in this configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Updates to enable omap aes
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
[tony@atomide.com: updated to use CONFIG_ARCH_OMAP2/3 instead of old 24XX/34XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix this and similar build warnings when building with
omap_4430sdp_defconfig.
CC arch/arm/mach-omap2/board-4430sdp.o
In file included from arch/arm/mach-omap2/board-4430sdp.c:36:
arch/arm/plat-omap/include/plat/usb.h:109: warning: return type defaults to 'int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
At Pandaboard we have 2 status leds, so adding them with similar usage as
we have for Beagleboard (heartbeat and mmc0). The patch basically adds the
platform data required by leds-gpio driver.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap 4430sdp board support for the proximity sensor via GPIO keys.
The proximity sensor is connected to GPIO and is registered as a
GPIO key.
- Making the default state of the sensor off at bootup
- The init is called before platform_add_devices
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP USBOTG module has a requirement to set the autoidle bit only after
setting smartidle bit. Modified the _sys_enable api to set the smartidle
first and then the autoidle bit. Setting this will not have any impact on the
other modules.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap4_cm_wait_module_ready function would only check for
the modules to be completely functional before declaring them
ready to be accessed.
There might also be instances where in the module is actually
in idle (under h/w control) but should still be declared
accessible, as the h/w control would make it functional when
needed.
Hence make omap4_cm_wait_module_ready return true in case
the module is fully functional *or* in idle state.
Fail only if the module is fully disabled or stuck intransition.
The explaination from the TRM for the idlest bits on OMAP4 is as
below for quick reference
Module idle state:
0x0 func: Module is fully functional, including OCP
0x1 trans: Module is performing transition: wakeup, or sleep, or sleep
abortion
0x2 idle: Module is in Idle mode (only OCP part). It is functional if
using separate functional clock
0x3 disabled: Module is disabled and cannot be accessed
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently there is a bug in the existing omap_device core code when
extracting the hwmod structures passed to omap_device_build_ss(). This bug
gets exposed only when passing multiple hwmod structures to
omap_device_build_ss() resulting in incorrect extraction from second hwmod
structure.
This fix uses the pointer to pointer to omap_hwmod structure (array of
pointers to omap_hwmod structure) passed to omap_device_build_ss() to
correctly extract the appropriate omap_hwmod structure.
This patch has been created and tested on lo/master and mainline.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Charulatha V <charu@ti.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
This patch is temporary fix to below crash. This is observed when
CPU is clocked more than 600 MHz.
Unhandled fault: imprecise external abort (0x1406) at 0xbf9ef65c
Internal error: : 1406 [#1] PREEMPT SMP
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.36-rc3+ #18)
PC is at kernel_thread_helper+0x0/0x14
LR is at kernel_thread_helper+0x0/0x14
pc : [<c003ce14>] lr : [<c003ce14>] psr: 00000093
sp : dc83bff8 ip : 00000000 fp : 00000000
r10: 00000000 r9 : 00000000 r8 : 00000000
r7 : 00000013 r6 : c003ce28 r5 : c008935c r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 00000000
Flags: nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7f Table: 8000404a DAC: 00000017
Process swapper (pid: 2, stack limit = 0xdc83a2f0)
Stack: (0xdc83bff8 to 0xdc83c000)
bfe0: 00000000 ffffffff
[<c003ce14>] (kernel_thread_helper+0x0/0x14) from [<fffffffe>] (0xfffffffe)
Code: c03a0ba3 c03a5fcb c045c880 c0394035 (eb017701)
---[ end trace 1b75b31a2719ed1c ]---
The timer hwmod adaptation will eventually fix it in a proper way.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
On ES2.0 the L2 cache init parameter ineeds to be changed to take
care of cache size. The cache size is 1MB on ES2.0 vs 512KB on ES1.0
This patch fixes the init parameter to update the same using
dynamic cpu version check
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch updates the id.c and cpu.h files to support
omap4 ES2.0 silicon detection. Few initial omap4 es2 samples
IDCODE is same as es1. So the patch uses ARM cpuid register to
detect the ES version for such samples
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
On OMAP4 there is no need to have SRAM_BOOTLOADER_SZ provision
Hence put this macro under CONFIG_ARCH_OMAP2PLUS check
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP24xx/34xx/44xx: omap_type() returns the correct type:
OMAP2_DEVICE_TYPE_TEST
OMAP2_DEVICE_TYPE_EMU
OMAP2_DEVICE_TYPE_SEC
OMAP2_DEVICE_TYPE_GP
OMAP2_DEVICE_TYPE_BAD
In current implementation there are two problems:
Problem 1:
For 34xx, the current if check will never return true.
Problem 2:
For 24xx the correct type check should be with omap_type() function
Verified by checking the TRM 24xx for CONTROL_STATUS register bits
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Bootloader on Nokia N800 and N810 muxes I2C codec port pins for EAC block.
As there is no driver and use for EAC, mux those pins for McBSP instead
since N810 ASoC drivers can use it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Second i2c bus on Nokia N800 and N810 shares both common and hw specific
peripherals. Register now this bus and add board info with tlv320aic3x for
N810. Common peripherals may be added as an additional board info to
omap_register_i2c_bus(2, ...);
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Move n8x0_i2c_board_info_1 out from #ifdef CONFIG_MENELAUS block,
register i2c1 in n8x0_init_machine and do a few clean-ups around these.
Code looks better if board infos are grouped together
- Mark n8x0_i2c_board_info_1 and n8x0_menelaus_platform_data with __initdata
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes these compiler warnings:
CC arch/arm/mach-omap2/mux.o
arch/arm/mach-omap2/mux.c: In function 'omap_mux_init_gpio':
arch/arm/mach-omap2/mux.c:90: warning: 'gpio_mux' may be used uninitial
ized in this function
CC arch/arm/plat-omap/gpio.o
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_resume_after_idle':
arch/arm/plat-omap/gpio.c:2152: warning: 'l' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_prepare_for_idle':
arch/arm/plat-omap/gpio.c:2085: warning: 'l2' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c:2085: warning: 'l1' may be used uninitialized
in this function
CC arch/arm/mach-omap2/board-omap4panda.o
arch/arm/mach-omap2/board-omap4panda.c: In function 'omap4_panda_init':
arch/arm/mach-omap2/board-omap4panda.c:277: warning: unused variable 's
tatus'
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding i2c eeprom driver to access monitor EDID binary information
from user space, something that is required by 'decode-edid' and
'parse-edid'.
BugLink: https://bugs.launchpad.net/bugs/608279
Signed-off-by: Mathieu Poirier <mathieu.poirier@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap3630 based BeagleBoard xM uses a MicroSD card slot with
no write protection.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
system_rev comes from u-boot and is a constant 0x20, so
Bx boards also fall in this 'if' and will get setup with the
wrong gpio_wp pin. Switch to using the Beagle revision routine
to correcly set pin 23 only for C1/2/3 and C4 Boards. Bx boards
will then use the correct default pin setting.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Due to the omap3530 ES3.0 Silicon being used on both the
B5/B6 and C1/2/3 Beagle we can't use the cpu_is_omap34xx()
routines to differentiate the Beagle Boards.
However gpio pins 171,172,173 where setup for this prupose, so
lets use them.
Changes:
for older U-Boot's, use omap_mux_init_gpio()
keep Beagle Rev in board-omap3beagle.c
gpio_free on gpio request failure
Tested on Beagle Revisions: B5, C2, C4, and xMA
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board file changes for the digital compass hmc5843.
The interface to the device is i2c.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If a GPIO bank has more than one GPIO with debounce enabled, the
debounce clock will not be fully disabled before going to
idle/suspend.
In the idle path, we just do a single clk_disable() of the bank's
debounce clock. If there are multiple debounce-enabled GPIOs in the
bank, that clocks usage count will be > 1, so the clk_disable() will
not actually disable the clock.
So the fix is to clk_disable() for every debounce-enabled GPIO in the
bank (and an equivalent clk_enable() of course.)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The OMAP4 L3 interconnect is split in 3 part for power saving reason.
Because of that there is no l3_main like on OMAP2 & 3 but 3 differentes
l3_main_X instances.
In the case of OMAP4, query only the l3_main_1 part. The clock and
voltage are shared across the 3 instances.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current version contains only the interconnects and the
mpu hwmods.
The remaining hwmods will be introduced by further patches on
top of this one.
- enable as well omap_hwmod.c build for OMAP4 Soc
Please not that this file uses the new naming convention for
naming HW IPs. This convention will be backported soon for previous
OMAP2 & 3 data files.
new name trm name
------------- -------------------
counter_32k synctimer_32k
l3_main l3
timerX gptimerX / dmtimerX
mmcX mmchsX / sdmmcX
dma_system sdma
smartreflex_X sr_X / sr?
usb_host_fs usbfshost
usb_otg_hs hsusbotg
usb_tll_hs usbtllhs_config
wd_timerX wdtimerX
ipu cortexm3 / ducati
dsp c6x / tesla
iva ivahd / iva2.2
kbd kbdocp / keyboard
mailbox system_mailbox
mpu cortexa9 / chiron
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In order to help differentiate omap_devices from normal
platform_devices, make them all a parent of a new common parent
device.
Then, in order to determine if a platform_device is also an
omap_device, checking the parent is all that is needed.
Users of this feature are the runtime PM core for OMAP, where we need
to know if a device being passed in is an omap_device or not in order
to know whether to call the omap_device API with it.
In addition, all omap_devices will now show up under /sys/devices/omap
instead of /sys/devices/platform
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This reverts commit 0007122ad8.
The dereference method of checking for a valid omap_device when
wrapping a platform_device is rather unsafe and dangerous.
Instead, a better way of checking for a valid omap-device is
to use a common parent device for all omap_devices, then a check
can simply be made using the device parent. The only user of this
API was the initial version of the runtime PM core for OMAP. This
has now been switched to check device parent, so there are no more
users of this API.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When the clockdomain layer initializes, place all clockdomains into
software-supervised mode, and clear all wakeup and sleep dependencies
immediately, rather than waiting for the PM code to do this later.
This fixes a major bug where critical sleep dependencies added by the
hwmod code are cleared during late PM init.
As a side benefit, the _init_{wk,sleep}dep_usecount() functions are no
longer needed, so remove them.
Kevin Hilman <khilman@deeprootsystems.com> did all the really hard work on
this, identifying the problem and finding the bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The set_pwrdm_state() is needed on omap4 as well so move
this routine to common pm.c file so that it's available for omap3/4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Commit 8e2efde9 added milliseconds suspend wakeup time support but
same interface is not exported through debugfs
This patch enables the debugfs hook for wakeup_timer_milliseconds
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch moves omap2_pm_wakeup_on_timer() and pm debug entries
form pm34xx.c to pm-debug.c and export it, so that it is available
to other OMAPs
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 has an iva device and a dsp devcice where as OMAP2/3
has only an iva device. In this file the iva device in the
system is registered under the name dsp_dev and the API
to retrieve the iva device is omap2_get_dsp_device.
This patch renames the dsp_dev to iva_dev, renames
omap2_get_dsp_device to omap2_get_iva_device,
registers dsp_dev for OMAP4 and adds a new API
omap4_get_dsp_device to retrieve the dep_dev.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In an effort to simplify the core idle path, move any device-specific
special case handling from the core PM idle path into the CPUidle
pre-idle checking path.
This keeps the core, interrupts-disabled idle path streamlined and
independent of any device-specific handling, and also allows CPUidle
to do the checking only for certain C-states as needed. This patch
has the device checks in place for all states with the CHECK_BM flag,
namely all states >= C2.
This patch was inspired by a similar patch written by Tero Kristo as
part of a larger series to add INACTIVE state support.
NOTE: This is a baby-step towards decoupling device idle (or system
idle) from CPU idle. Eventually, CPUidle should only manage the CPU,
and device/system idle should be managed elsewhere.
Cc: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This change adds in MMC and I2C support to the HTC Herald board, as well
as adding the HTCPLD driver for the PLD used on this phone. It also
adds in the gpio-keys entries for the front directional keys and
selector and the cursor keys on the slide-out keyboard, and gpio-leds
support for the LEDs attached to the htcpld.
Additionally, SPI bus support (using the spi100k driver) and
touchscreen support (using the ads7846 driver) were added.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch:
- adds more documentation to the hwmod code
- fixes some documentation typos elsewhere in the file
- changes the _sysc_*() function names to appear in (verb, noun) order,
to match the rest of the function names.
This patch should not result in any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
For every optional clock present per hwmod per omap-device, this function
adds an entry in the clocks list of the form <dev-id=dev_name, con-id=role>,
if an entry is already present in the list of the form <dev-id=NULL, con-id=role>.
The function is called from within the framework inside omap_device_build_ss(),
after omap_device_register.
This allows drivers to get a pointer to its optional clocks based on its role
by calling clk_get(<dev*>, <role>).
Link to discussions related to this patch:
http://www.spinics.net/lists/linux-omap/msg34809.html
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: simplified loop iterator; removed the superfluous clk_get(),
using the clk_get() in clk_add_alias() instead]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Rajendra Nayak
Lennert Buytenhek
Tony Lindgren
Sukumar Ghorai
Jarkko Nikula
Peter Ujfalusi
Subramaniam C.A
Dmitry Kasatkin
Anand Gadiyar
Ricardo Salveti de Araujo
Shubhrajyoti Datta
Hema HK
Kishon Vijay Abraham I
Santosh Shilimkar
David Anders
Vikram Pandita
Sanjeev Premi
Mathieu J. Poirier
Robert Nelson
Kevin Hilman
Benoit Cousson
Paul Walmsley
Thara Gopinath
Cory Maccarrone
Partha Basak