__mem_pci is only used to enable readl/writel and friends. Just condition
this on readl being defined and remove all the __mem_pci defines.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@nvidia.com>
Move tegra specific mach/io.h parts into iomap.h.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Colin Cross <ccross@android.com>
Cc: Olof Johansson <olof@lixom.net>
This causes the Tegra pinctrl driver to be built whenever core Tegra
support is enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra pinmux, and required parameterization
data for Tegra20 and Tegra30.
The driver is initially added with driver name and device tree compatible
value that won't cause this driver to be used. A later change will switch
the pinctrl driver to use the correct values, switch the old pinmux
driver to be disabled, and update all code that uses the old pinmux APIs
to use the new pinctrl APIs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
[squashed "fix case of Tegra30's foo_groups[] arrays"]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra board updates. Most of the board updates for tegra30 and for some
of the driver device-tree conversions have gone in through the other
branches, so that leaves quite little left here -- mostly a couple
of updates to the not-yet-converted tegra2 boards and a couple of
device-tree updates.
* tag 'tegra-boards' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: match SoC name not board name in DT board files
ARM: tegra: PCIe: Provide 3.3V supply voltage
ARM: dt: tegra: add the wifi led to paz00 device tree
ARM: dt: tegra: add the power gpio key to paz00 device tree
ARM: dt: tegra: add ADT7461 temperature sensor to paz00 device tree
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tegra SoC driver support.
Some device tree conversions, some new drivers. and a fix for an issue
introduced in Grant Likely's irq_domain conversion in his tree. Because
of that, this branch depends on his branch to build (but not to merge):
git://git.secretlab.ca/git/linux-2.6.git irqdomain/next
* tag 'tegra-soc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra: (34 commits)
ARM: tegra: uncompress.h: Don't depend on kernel headers
gpio: tegra: Fix build issue due to irq_domain rework.
ARM: tegra: Remove duplicate PMU interrupt inversion code
ARM: tegra: Add a simple PMC driver
ARM: tegra: dma: not required to move requestor when stopping.
ARM: tegra: Fix EMC pdata initialization from registers
gpio: tegra: Parameterize the number of banks
gpio: tegra: Dynamically allocate IRQ base, and support DT
ARM: tegra: Remove use of TEGRA_GPIO_TO_IRQ
ARM: tegra: Pass uncompress.h UART selection to DEBUG_LL
ARM: tegra: uncompress.h: Choose a UART at runtime
ARM: tegra: uncompress.h: Store UART address in a variable
ARM: tegra: Introduce define DEBUG_UART_SHIFT
ARM: tegra: Support Tegra30 in decompressor UART setup
ARM: tegra: Pause DMA when reading transfer count
ARM: tegra: emc: device tree support
ARM: tegra: emc: convert tegra2_emc to a platform driver
ARM: tegra: fuse: add bct strapping reading
ARM: tegra: fuse: add functions to access chip revision
ARM: tegra: fuse: use apbio dma for register access
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From: Olof Johansson <olof@lixom.net>
SoC new development for tegra SoCs, mostly tegra30 core support.
It also includes one stray bugfix that was misapplied (should have been
in soc-drivers), but it went out to the stable branches before I noticed
so I've left it in.
* tag 'tegra-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: Demote EMC clock inconsistency BUG to WARN
ARM: tegra: Avoid compiling cpuidle code when not configured
ARM: tegra: cpuidle driver for tegra
ARM: tegra: assembler code for LP3
ARM: tegra: definitions for flow controller
ARM: tegra: initialize basic system clocks
ARM: tegra: enable tegra30 clock framework
ARM: tegra: implement basic tegra30 clock framework
ARM: tegra: add support for new clock framework features
ARM: tegra: add support for tegra30 interrupts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor fixes that weren't urgent enough to go into 3.3. The two paz00
patches are in mainline already but got merged after the branch point
for this branch, so they're duplicated. I also ended up merging in
rmk/for-armsoc into this later on to fix a bug introduced by it, so it's
included but it's not the base of this branch.
* tag 'tegra-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: Enable CPUIdle on Tegra20
ARM: tegra: export usb phy symbols
ARM: tegra: build localtimer support only when needed
ARM: tegra: select CPU_FREQ_TABLE
ARM: tegra: select required CPU and L2 errata options
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor fixes that weren't urgent enough to go into 3.3. The two paz00
patches are in mainline already but got merged after the branch point
for this branch, so they're duplicated. I also ended up merging in
rmk/for-armsoc into this later on to fix a bug introduced by it, so it's
included but it's not the base of this branch.
* tag 'tegra-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: Enable CPUIdle on Tegra20
ARM: tegra: export usb phy symbols
ARM: tegra: build localtimer support only when needed
ARM: tegra: select CPU_FREQ_TABLE
ARM: tegra: select required CPU and L2 errata options
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As the LP3 code also works for Tegra20, we can enable cpuidle for Tegra20.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ehci driver can be a module, so the functions provided
by the tegra platform code used by ehci-tegra need to
be exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Olof Johansson <olof@lixom.net>
It is possible to build a tegra kernel without localtimer
support, so the tegra specific parts should only be built
when that is indeed enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Olof Johansson <olof@lixom.net>
The tegra cpufreq implementation relies on the cpu_freq_table
code, so make sure that this is always there when needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ports are used as follows:
UART1/A: Routed to debug dongle
UART2/B: GPS
UART3/C: Bluetooth
UART4/D: Routed to debug dongle
UART5/E: Not connected
The debug dongle has jumpers to connect either UART1/A or UART4/D to
the DB-9 connector. UART1/A is typically used on Cardhu, and is the option
we assume here.
For now, only enable UART1/A, and explicitly disable all other ports.
The explicit disable prevents the message "of_serial 70006040.serial:
no clock-frequency property set" being printed during boot.
Enabling the other ports requires their clocks to be enabled, or accesses
to the registers will hang. At present, this requires adding entries into
board-dt-tegra30.c's tegra_dt_clk_init_table[]. Lets punt on that and wait
for the common clock bindings to set this all up, although that will also
requiring adding clock support to 8250.c.
While we're at it, fix board-dt-tegra30.c to enable the correct clock for
the debug UART. We got away with this before, because the bootloader already
enabled it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
board-dt-tegra*.c should support any board using Tegra when booted using
device tree. Instead of explicitly listing all the supported boards,
which requires a kernel change for each new board, list the supported SoC
model instead.
Note that the board files do currently have explicit support for setting
up each board's pinmux. However, it's fairly likely that at least the
basic devices on any new board will work just fine as set up by the boot-
loader, and the pinmux data should be moving into device tree soon anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPTeeMAAoJEIaOsuA1yqRE6ZAP/j2G6DaDyng6vpyYQi2drXaY
NKx3pA0sC98NACOv6sh+urcMDcDctLmOnwV18U+GNNP+qExQFnyuc7iGsXRxfUOj
qkIbVPxzPcE0opmEMFJ5ZT85rw33DqKjFnQT4av3wwXe/qSrEkAfBoBSb6wn73rA
v0JOhceGsFb+kJAc7U9Ji9A9xSjj+6uw08RTuuQv8KBLb5Pws+NoQ6UEjlni8umA
lkOSelyBZN1OJU+fZKIpS4+SiwtdkZCm2wSIUiwaPosdJgw0w8fz0zNjn/4gAHB1
oPyjjjP3/VDegp9CuYDRlnBgQa2K4V1vbjrBfhKbyar8fsOSoaPVv1fR9VKgVnT8
RKlXKSeFEsdP4fOGYCjNKAzjeQH/qSNzdzo+s4GMqoWq7Lm3+b56zdQWvRmTT7Xg
++bMqFAi0noeU8aZWwSDMFiYv6O19o+Px4OTS/3aRmR1wdJpUUSk2M7Quw6A/YNj
4Q5hDvio2eYtI1nya9yMS/j4ZiJ5fDQb5jUfBDB1MKtkZKKzVVSboK8P/rFq5+xf
xdUfBRd7/fMk+he6RtemfjhMdYTiX6Cm6VzveZVBL4+7dERbnJDRgDhSJOYvA/eW
Bvc7BY+/EYz7msF0gjLyWu3BBiChajk/D5ukoCIssUPGuIhmO1S7JRi1s+fLaNs3
Bz8Haxql69YWrNL2ouQf
=WiB6
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB: transceiver changes for 3.4
Here we have a big rework done by Heikki Krogerus (thanks) which
splits OTG functionality away from transceivers.
We have known for quite a long time that struct otg_transceiver was
a bad name for the structure, considering transceiver is far from
being OTG-specific (see 4e67185).
* 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix L4_EMU_34XX_BASE error after iomap changes
ARM: OMAP2+: Limit omap_read/write usage to legacy USB drivers
ARM: OMAP: Remove plat/io.h by splitting it into mach/io.h and mach/hardware.h
ARM: OMAP2+: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move most of plat/io.h into local iomap.h
ARM: OMAP1: Move 16xx GPIO system clock to platform init code
ARM: OMAP: Move omap_init_consistent_dma_size() to local common.h
ARM: OMAP2+: Move SDRC related functions from io.h into local common.h
ARM: OMAP2+: Drop DISPC L3 firewall code
ARM: OMAP2xxx: PM: remove obsolete timer disable code in the suspend path
ARM: OMAP: McSPI: Remove unused flag from struct omap2_mcspi_device_config
(update to latest rmk/for-arm-soc branch)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This fixes the following compile error:
CC arch/arm/boot/compressed/misc.o
In file included from arch/arm/boot/compressed/misc.c:28:0:
arch/arm/mach-tegra/include/mach/uncompress.h: In function 'arch_decomp_setup':
arch/arm/mach-tegra/include/mach/uncompress.h:125:2: error: implicit declaration of function 'BUILD_BUG_ON_ZERO' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
This is due to use of the ARRAY_SIZE() macro. Typically, this would be
solved by including <linux/bug.h>, but the compressor code isn't part of
the kernel, and so should not include kernel headers. Instead, define
the few macros the code uses directly, and in a way that doesn't depend
on <linux/bug.h>.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the new usb_phy_* functions with transceiver
operations instead of the old otg functions.
Includes fixes from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for bringing up secondary cores on Tegra30. On Tegra30 secondary
CPU cores are powergated, so we need to turn on the domains before we can bring
the CPU cores online. Bringing secondary cores online happens early during the
sytem boot, so we call powergating initialization from platform early_init
function.
Based on work by:
Scott Williams <scwilliams@nvidia.com>
Colin Cross <ccross@android.com>
Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Secondary CPU powerdomains can be powergated on Tegra30. Add the necessary
functions to do this. This will be used to boot the secondary CPUs later on.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the new powerdomains in Tegra30 such as extra CPU cores and
the SATA domain.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Export tegra_powergate_is_powered(). This function will be used by the Tegra30
code to bringup secondary CPU cores.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Prepare the powergating code for other Tegra variants which have a different
number of powerdomains.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Prepare the Tegra secondary CPU core bringup code for other Tegra variants.
The reset handler is also generalized to allow for future introduction of
powersaving modes which turn off the CPU cores.
Based on work by:
Scott Williams <scwilliams@nvidia.com>
Chris Johnson <cwj@nvidia.com>
Colin Cross <ccross@android.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Introduce some functions to write to the flowcontroller registers. The
flowcontroller controls CPU sleepstates and wakeup.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Secondary core bringup relies on the Tegra chipid to distinguish between
Tegra variants. Therefore this data needs to be available early on.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The powergating and reset handling code needs to differentiate between Tegra
variants. Therefore we export the chipid here.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The chipid register contains information about the Tegra variant and revision.
We want differentiate between Tegra variants for powergating and secondary
core bringup. This patch cleans up the reading and decoding of this register.
In subsequent patches the variant will exported as a global variable.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The PCIe reference clock needs a 3.3V supply voltage to work properly.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The ARM IP revisions in Tegra are:
Tegra20: CPU r1p1, PL310 r2p0
Tegra30: CPU A01=r2p7/>=A02=r2p9, NEON r2p3-50, PL310 r3p1-50
Based on work by Olof Johansson, although the actual list of errata is
somewhat different here, since I added a bunch more and removed one PL310
erratum that doesn't seem applicable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
When this inconsistency occurs, the system will typically operate without
issue, it's just that EMC scaling won't optimally. Convert the BUG_ON to
a WARN_ONCE in order to allow the kernel to boot, but still complain.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
No need to compile cpuidle.c and sleep.S if cpuidle isn't configured in the
kernel.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* lpc32xx/drivers: (566 commits)
ARM: LPC32xx: ADC support for mach-lpc32xx
Includes an update to Linux 3.3-rc4
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
This is the first step in separating USB transceivers from
USB OTG utilities.
Includes fixes to IMX code from Sascha Hauer.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Li Yang <leoli@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The new PMC driver now configures the PMU interrupt inversion, so board
files don't need to poke the PMC registers directly to achieve this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
UARTC is connected to the mini-pcie port.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The power gpio for the external memory card was specified wrongly.
Replace it with the correct value (tested with warmboot with fastboot).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This PMC driver is enough to parse the nvidia,invert-interrupt property
from device tree, and configure the PMC's to honor that.
In the future, this file could expand to centralize all other PMC accesses
within the mach-tegra code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
It is not require to move the requestor of dma to INVALID
option before stopping dma.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit d91eeb0 "ARM: tegra: emc: device tree support" modified the EMC
driver to create an EMC table from existing register settings when none
was provided through platform data or device tree. This code wrote the
wrong clock rate into the table; the actual rate in Hz, rather than the
expected half-rate in KHz. This caused the BUG_ON in
tegra2_emc_clk_round_rate() to fire, since that enormous rate could not
be generated.
Fixes:
[ 2.425921] kernel BUG at arch/arm/mach-tegra/tegra2_clocks.c:1158!
...
[ 2.618766] [<c001c0e8>] (tegra2_emc_clk_round_rate+0x58/0x70) from [<c00198b4>] (clk_round_rate+0x48/0x68)
[ 2.628494] [<c00198b4>] (clk_round_rate+0x48/0x68) from [<c0019cc0>] (clk_set_rate_locked+0x40/0x68)
[ 2.637707] [<c0019cc0>] (clk_set_rate_locked+0x40/0x68) from [<c0019d10>] (clk_set_rate+0x28/0x40)
[ 2.646754] [<c0019d10>] (clk_set_rate+0x28/0x40) from [<c001ffc8>] (tegra_update_cpu_speed+0x54/0x144)
[ 2.656144] [<c001ffc8>] (tegra_update_cpu_speed+0x54/0x144) from [<c002016c>] (tegra_target+0xb4/0xe0)
[ 2.665538] [<c002016c>] (tegra_target+0xb4/0xe0) from [<c01a96c0>] (__cpufreq_driver_target+0x88/0xa4)
[ 2.674931] [<c01a96c0>] (__cpufreq_driver_target+0x88/0xa4) from [<c01ac9d0>] (dbs_check_cpu+0x324/0x340)
[ 2.684582] [<c01ac9d0>] (dbs_check_cpu+0x324/0x340) from [<c01aca40>] (do_dbs_timer+0x54/0xf4)
[ 2.693277] [<c01aca40>] (do_dbs_timer+0x54/0xf4) from [<c00369a8>] (process_one_work+0x1d4/0x320)
[ 2.702225] [<c00369a8>] (process_one_work+0x1d4/0x320) from [<c0036f34>] (worker_thread+0x134/0x230)
[ 2.711437] [<c0036f34>] (worker_thread+0x134/0x230) from [<c003add0>] (kthread+0x80/0x8c)
[ 2.719700] [<c003add0>] (kthread+0x80/0x8c) from [<c000ebf4>] (kernel_thread_exit+0x0/0x8)
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[olof: fixed calculation of printed values]
Signed-off-by: Olof Johansson <olof@lixom.net>
Enhance the driver to dynamically allocate the base IRQ number, and
create an IRQ domain for itself. The use of an IRQ domain ensures that
any device tree node interrupts properties are correctly parsed.
Describe interrupt-related properties in the device tree binding docs,
and the contents of "child" node interrupts property.
Update tegra*.dtsi to specify the required interrupt-related properties.
Finally, remove the definition of TEGRA_GPIO_TO_IRQ; this macro no longer
gives correct results since the IRQ numbers for GPIOs are dynamically
allocated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
Replace compile-time usage of TEGRA_GPIO_TO_IRQ with run-time calls to
gpio_to_irq(). This will allow the base IRQ number for the Tegra GPIO
driver to be dynamically allocated in a later patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
uncompress.h now saves the selected UART's physical address in Tegra's
IRAM, along with a cookie to indicate validity.
The first time it's run, macro addruart in debug-macro.S looks for this
cookie, and if it's present, uses the UART address stored there. If not,
the static value TEGRA_DEBUG_UART_BASE is used, as was previous behaviour.
The static behaviour will thus be used when not booting using a zImage.
This work was inspired by work by Doug Anderson <dianders@chromium.org>;
see http://lkml.org/lkml/2011/9/26/284. However, this patch relies on
the data passing describe above, rather than duplicating the UART
selection logic in debug-macro.S; the latest selection logic is more
complex due to the need to check reset/clock bits too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
With this change we automatically detect which UART to use for
for printing during decompression. The detection involves coordination
with the bootloader: it's expected that the bootloader will leave a
'D' (for [D]ebug) in the UART scratchpad register for whichever UART we
should use for debugging.
If we don't find any such UART, we fall back to the UART that was
specified during config time: CONFIG_TEGRA_DEBUG_UART_XXX.
As a side effect of this change, uncompress debug messages will work
if you've specified CONFIG_TEGRA_DEBUG_UART_NONE, provided the
bootloader obeys the protocol.
This change is in line with what is documented in
Documentation/arm/Booting.
Other approaches considered:
* Hardcode based on machine ID (as many other ARM boards do).
OK, but nice to not have yet another place to add per-board
code. Better to have bootloader parse device tree and pass us
this info.
* Check for TXE bit (like SA1110). Nice (and doesn't require
a bootloader change), but a little less explicit. Also: if
bootloader (for some reason) uses another UART, it needs to
remember to turn it off before jumping to the kernel or we may
print to it. NOTE: adapting this patch to check TXE too would
be easy if desired.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[swarren: Added clock/reset condition checks]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This will allow a future change to auto-detect which UART to use.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[swarren: Extracted from a larger patch by Doug]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This removes the need for the variable "shift" in all functions in
uncompress.h.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[swarren: Extracted from a larger patch by Doug]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
On Tegra20, the UART clock runs at 216MHz, whereas on Tegra30 it runs at
408MHz. Modify arch_decomp_setup() to detect Tegra20-vs-Tegra30 at run-
time, and program the correct divisor.
This makes uncompressor messages work correctly on Tegra30. This also
fixes early printk, assuming zImage is used and this setup code runs.
v2: Use CHIPID register to differentiate between chips, rather than a
GIC register. This should be more future-proof. Volatile is required
to prevent the compiler transforming the 32-bit apb_misc register read
into an 8-bit read of address 1 higher, since the HW only supports 32-
bit accesses, and will hang on an 8-bit access.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to read an accurate channel transfer count
from the APB DMA engine, the DMA controller must be
paused first.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add device tree support to the emc driver, filling in the platform data
based on the DT bindings.
Changes since v1:
* Unmangled some messed up patch squashes, moving changes to earlier patches
* Flipped an of_property_read_u32 return value test
* Clarified clock settings message on case where no table is provided
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
This is the first step in making it device-tree aware and get rid of the
in-kernel EMC tables (of which there are none in mainline, thankfully).
Changes since v3:
* moved to devm_request_and_ioremap() in probe()
Changes since v2:
* D'oh -- missed a couple of variables that were added, never used and then
later removed in a later patch.
Changes since v1:
* Fixed messed up indentation
* Removed code that should be gone (was added here and removed later in series)
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Add function to get chip revision, and print it out at boot time.
Restructure the fuse access to just use cached variables instead
of always reading the fuses, and export those variables directly
instead of using accessor functions.
Add a SKU ID table of currently known values.
Based on code originally by Colin Cross <ccross@android.com>.
Changes since v1:
* Add A01 minor rev support
* Don't decode for A03p on anything but T2x
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tegra2 hangs if APB registers are accessed from the cpu during an
apb dma operation. The workaround is to use apb dma to read/write the
registers instead.
There is a dependency loop between fuses, clocks, and APBDMA. If dma
is enabled, fuse reads must go through APBDMA to avoid corruption due
to a hw bug. APBDMA requires a clock to be enabled. Clocks must read
a fuse to determine allowable cpu frequencies.
Separate out the fuse DMA initialization, and allow the fuse read
and write functions to be called without using DMA before the DMA
initialization has been completed. Access to the fuses before APBDMA
is initialized won't hit the hardware bug because nothing else can be
using DMA.
Original fuse registar access code from Varun Wadekar
<vwadekar@nvidia.com>, improved by Colin Cross <ccross@android.com>
and later moved to separate driver by Jon Mayo <jmayo@nvidia.com>.
Major refactoring/cleanup by Olof Johansson <olof@lixom.net>.
Changes since v1:
* fix 'return false' on error condition
* dequeue dma ops in case of timeout
From: Jon Mayo <jmayo@nvidia.com>.
Signed-off-by: Jon Mayo <jmayo@nvidia.com>.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Since we'll do opportunistic allocations before the dma subsystem is
enabled we want just silent failures and retries instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
The power gpio for the external memory card was specified wrongly.
Replace it with the correct value (tested with warmboot with fastboot).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
CPUidle driver for tegra. In this version only LP3 (clockgating) is supported.
Based on work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Configure the flow controller for clockgating and enter WFI
Based on work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Introduce some definitions for the tegra flow contoller. This will be
used by the code which controls entering and leaving LP3.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Initialize basic system clocks and provide a auxdata table to allow some
peripheral drivers to find their clocks.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add init calls for clocks on tegra30.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add basic tegra30 clock framework. Not all clocks are supported yet. Mainly
clocks requiring voltage scaling are not yet implemented in this version.
Based on work by Alex Frid <afrid@nvidia.com> and
Scott Williams <scwilliams@nvidia.com>.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for new clock framework features implemented in tegra30.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra30 has 1 extra legacy interrupt controller. Use the GIC ITLinesNumber
field to determine how many interrupt controllers we have and initialize
appropriately. Also make room for the extra tegra30 interrupts by moving
the GPIO IRQ base. This shouldn't affect existing code as it determines the
correct IRQ number for GPIOs using TEGRA_GPIO_TO_IRQ().
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Allow marking some of GPIO pins as ignored to to avoid continuously
generating KBC input events.
Signed-off-by: Shridhar Rasal <srasal@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There's no need to keep the DMA_REQ_SEL defines inside the ifdef.
Fixes the following build break with CONFIG_TEGRA_SYSTEM_DMA=n:
arch/arm/mach-tegra/devices.c:645: error: 'TEGRA_DMA_REQ_SEL_I2S_1' undeclared here (not in a function)
arch/arm/mach-tegra/devices.c:663: error: 'TEGRA_DMA_REQ_SEL_I2S2_1' undeclared here (not in a function)
arch/arm/mach-tegra/devices.c:663: error: initializer element is not constant
arch/arm/mach-tegra/devices.c:663: error: (near initialization for 'i2s_resource2[1].start')
arch/arm/mach-tegra/devices.c:664: error: initializer element is not constant
arch/arm/mach-tegra/devices.c:664: error: (near initialization for 'i2s_resource2[1].end')
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Add support for Tegra30 by correcting definitions. This is necessary to
make driver useful in Tegra30.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Acked-by: Stephen Warren: <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The crypto driver will need this api to use
it in the RNG calculations. In order to build
the crypto driver as a module, tegra_chip_uid
has to be exported.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Henning Heinold <heinold@inf.fu-berlin.de>
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
ALSA: usb-audio: add Yamaha MOX6/MOX8 support
ALSA: virtuoso: add S/PDIF input support for all Xonars
ALSA: ice1724 - Support for ooAoo SQ210a
ALSA: ice1724 - Allow card info based on model only
ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
ALSA: hdspm - Provide unique driver id based on card serial
ASoC: Dynamically allocate the rtd device for a non-empty release()
ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
ALSA: hda/cirrus - support for iMac12,2 model
ASoC: cx20442: add bias control over a platform provided regulator
ALSA: usb-audio - Avoid flood of frame-active debug messages
ALSA: snd-usb-us122l: Delete calls to preempt_disable
mfd: Put WM8994 into cache only mode when suspending
...
Fix up trivial conflicts in:
- arch/arm/mach-s3c64xx/mach-crag6410.c:
renamed speyside_wm8962 to tobermory, added littlemill right
next to it
- drivers/base/regmap/{regcache.c,regmap.c}:
duplicate diff that had already come in with other changes in
the regmap tree
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tc3589x-keypad - add missing kerneldoc
Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
Input: ucb1400_ts - convert to threaded IRQ
Input: ucb1400_ts - drop inline annotations
Input: usb1400_ts - add __devinit/__devexit section annotations
Input: ucb1400_ts - set driver owner
Input: ucb1400_ts - convert to use dev_pm_ops
Input: psmouse - make sure we do not use stale methods
Input: evdev - do not block waiting for an event if fd is nonblock
Input: evdev - if no events and non-block, return EAGAIN not 0
Input: evdev - only allow reading events if a full packet is present
Input: add driver for pixcir i2c touchscreens
Input: samsung-keypad - implement runtime power management support
Input: tegra-kbc - report wakeup key for some platforms
Input: tegra-kbc - add device tree bindings
Input: add driver for AUO In-Cell touchscreens using pixcir ICs
Input: mpu3050 - configure the sampling method
Input: mpu3050 - ensure we enable interrupts
Input: mpu3050 - add of_match table for device-tree probing
Input: sentelic - document the latest hardware
...
Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lYb/
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Board-level changes
This adds and extends support for specific boards on a number of
ARM platforms: omap, imx, samsung, tegra, ...
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits)
Enable 32 bit flash support for iMX21ADS board
ARM: mx31pdk: Add MC13783 RTC support
iomux-mx25: configuration to support CSPI3 on CSI pins
MX1:apf9328: Add i2c support
mioa701: add newly available DoC G3 chip
arm/tegra: remove __initdata annotation from pinmux tables
arm/tegra: Use bus notifiers to trigger pinmux setup
arm/tegra: Refactor board-*-pinmux.c to share code
arm/tegra: Fix mistake in Trimslice's pinmux
arm/tegra: Rework Seaboard-vs-Ventana pinmux table
arm/tegra: Remove useless entries from ventana_pinmux[]
arm/tegra: PCIe: Remove include of mach/pinmux.h
arm/tegra: Harmony PCIe: Don't touch pinmux
arm/tegra: Add AUXDATA for tegra-pinmux and tegra-gpio
arm/tegra: Split Seaboard GPIO table to allow for Ventana
ARM: imx6q: generate imx6q dtb files
arm/imx6q: Rename Sabreauto to Armadillo2
arm/imx6q-sabrelite: add enet phy ksz9021rn fixup
arm/imx6: add imx6q sabrelite board support
dts/imx: rename uart labels to consistent with hw spec
...
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hp8k
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
SoC-level changes for tegra and omap
This adds support for the new tegra30 SoC, as well as small
changes to support minor variations of existing omap SoCs.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF
arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC
arm/tegra: Delete tegra_init_clock()
arm/tegra: Fix section mismatch errors in tegra30 pinmux
arm/tegra: Fix section mismatch errors in tegra20 pinmux
arm/tegra: refresh defconfig for tegra30
arm/tegra: add support for tegra30 based board cardhu
arm/tegra: implement support for tegra30
arm/tegra: pinmux tables and definitions for tegra30
arm/tegra: add new fields to struct tegra_pingroup_desc
arm/tegra: prepare pinmux code for multiple tegra variants
arm/tegra: rename tegra20 pinmux files
arm/tegra: generalize L2 cache initialization
arm/tegra: use PMC reset
arm/tegra: rename board-dt.c to board-dt-tegra20.c
arm/tegra: prepare early init for multiple tegra variants
arm/tegra: don't export clk_measure_input_freq
arm/tegra: prepare clock code for multiple tegra variants
arm/tegra: cleanup tegra20 support
arm/tegra: clk_get should not be fatal
...
Fix up trivial conflict in arch/arm/mach-tegra/board-dt-tegra20.c
Conflicts:
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-omap2/board-ti8168evm.c
arch/arm/mach-s3c64xx/Kconfig
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/common.c
Lots of relatively simple conflicts between the board
changes and stuff from the arm tree. This pulls in
the resolution from the samsung/cleanup tree, so we
don't get conflicting merges.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* samsung/dt: (3 commit)
Merge branch 'depends/rmk/for-linus' into samsung/dt
Merge branch 'depends/rmk/restart' into next/cleanup
Merge branch 'next/cleanup' into samsung/dt
Conflicts:
arch/arm/mach-tegra/board-dt.c
arch/arm/mach-tegra/include/mach/entry-macro.S
The latest version of the samsung/dt branch resolves
all sorts of conflicts with the latest upstream, no functional
changes that are not already there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-exynos/common.c
The common.c file gets changes from rmk/stable-devel (part of
next/cleanup), rmk/restart, samsung/dt and follow-on branches
from the samsung tree.
Pulling it all together here hopefully avoids having to do
even more conflicting merge changesets in this one file. What
a mess!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-tegra/board-harmony-pcie.c
To fix an internal merge conflict between the tegra/soc and tegra/boards
branches.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups. This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* tegra/dt:
arm/tegra: Seaboard: Add GPIO key device tree nodes
arm/dt: Add ADT7461 to Seaboard
arm/dt: tegra: Use new compatible value for DVC I2C controller
arm/tegra: initial device tree for tegra30
arm/tegra: convert tegra20 to GIC devicetree binding
arm/dt: tegra: Fix SDHCI nodes to match board files
arm/dt: tegra: Fix serial nodes to match board files
arm/dt: tegra: Fix I2C nodes to match board files
arm/dt: tegra: Remove /chosen node
arm/dt: tegra: Remove /memreserve/ from device-tree files
arm/tegra: board-dt: Enable audio-related clocks
arm/tegra: board-dt: Fix AUXDATA typo
arm/dt: tegra: add dts file for paz00
arm/tegra: Add device-tree support for TrimSlice board
arm/dt: tegra: Clean up I2S and DAS nodes
USB: ehci-tegra: add probing through device tree
arm/dt: add basic usb nodes to tegra device trees
arm/tegra: fix variable formatting in makefile
Conflicts:
arch/arm/mach-tegra/Makefile
* tegra/soc:
arm/tegra: Compile tegra_dt_init_irq only when CONFIG_OF
arm/tegra: Make MACH_TEGRA_DT depend on ARCH_TEGRA_2x_SOC
arm/tegra: Delete tegra_init_clock()
arm/tegra: Fix section mismatch errors in tegra30 pinmux
arm/tegra: Fix section mismatch errors in tegra20 pinmux
arm/tegra: refresh defconfig for tegra30
arm/tegra: add support for tegra30 based board cardhu
arm/tegra: implement support for tegra30
arm/tegra: pinmux tables and definitions for tegra30
arm/tegra: add new fields to struct tegra_pingroup_desc
arm/tegra: prepare pinmux code for multiple tegra variants
arm/tegra: rename tegra20 pinmux files
arm/tegra: generalize L2 cache initialization
arm/tegra: use PMC reset
arm/tegra: rename board-dt.c to board-dt-tegra20.c
arm/tegra: prepare early init for multiple tegra variants
arm/tegra: don't export clk_measure_input_freq
arm/tegra: prepare clock code for multiple tegra variants
arm/tegra: cleanup tegra20 support
arm/tegra: clk_get should not be fatal
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
Instead of reshuffling what functions in the pinmux paths should be
__init and thus could keep references to __initdata, let's just remove
the annotations for now -- the tables are moving to device tree in the
next version anyway and the whole subsystem is being wired up. We will
go back and re-annotate where appropriate once things settle down.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
This fixes a build break attempting to build a Tegra20-only kernel
without device tree enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that Tegra20 and Tegra30 device tree board files are separate,
MACH_TEGRA_DT (which enables the Tegra20 device tree board file) should
depend on Tegra20 support being enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
tegra_init_clock() is written to call tegra2_init_clocks(), which only
exists if Tegra20 support is enabled. This breaks the build of a
Tegra30-only kernel.
tegra_init_clock() isn't actually used any more; tegra20_init_early()
calls tegra2_init_clocks() directly. So, just delete this function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
tegra30_pinmux_init() is called from the pinmux's probe() function, and
hence should be __devinit not __init.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
tegra20_pinmux_init() is called from the pinmux's probe() function, and
hence should be __devinit not __init.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently, the Tegra pinmux is initialized at different times when booting
with and without device tree:
Without device tree:
1) Pinmux and GPIO drivers are registered.
2) Pinmux is configured.
3) All other drivers are registered.
With device tree:
1) All drivers are registered and probed, including pinmux and GPIO.
2) Pinmux is configured.
This change modifies board-pinmux.c to detect pinmux and GPIO driver
registration using bus notifiers. This allows pinmux configuration to
happen immediately after the pinmux driver is probed, irrespective of
whether the pinmux driver is manually registered by board-pinmux.c, or
if it's instantiated during device tree parsing.
To support this with device tree, the pinmux init functions must be
called prior to instantiating devices from device tree, so that the
notifiers are set up before-hand.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This moves the implementation of *_pinmux_init() into a single location.
The board-specific pinmux data is left in each board's own file. This
will allow future changes that set up the pinmux in a more complex
fashion to do so without duplicating that code in each board's pinmux
file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pin group PTA does not support function RSVD3. However, the current
pinmux driver doesn't check this when setting RSVD functions, and ends
up writing 3 to the HW register. 3 is actually represented by function
GMI, so update the pinmux table to request that instead in order to
obtain the same register programming without requesting invalid
configurations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rather than modifying seaboard_pinmux[] using ventana_pinmux[], split
seaboard_pinmux[] into common_pinmux[] and seaboard_pinmux[], and then
actually apply common_pinmux[] always, followed by the appopriate one
of seaboard_pinmux[] or ventana_pinmux[].
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Some of the entries in ventana_pinmux[] are identical to what's already in
seaboard_pinmux[]. Remove the overrides from the Ventana table.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Harmony pinmux table is already set up to mux the PCIe signals onto
the appropriate pin groups. Don't manually fiddle with the pinmux in the
Harmony PCIe setup code.
Merge note: This will have a merge conflict with Peter De Schrijver's
"arm/tegra: prepare pinmux code for multiple tegra variants" due to
context. When merging the two, make sure to also remove the include
of <mach/pinmux-tegra20.h> that his patch added, since it's no longer
needed after this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The pinctrl device name is included in the pinctrl map table, and used
as a parameter to pin_config_*() functions. Hence, it must be the same
for non-DT and DT kernels. Add AUXDATA to cause this.
The GPIO device name will be used by the pinmux/GPIO initialization code
in a later patch, and needs to stay constant.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Seaboard and Ventana share some GPIOs, but others are different. Split the
GPIO table into common, seaboard-specific, and ventana-specific tables, so
that only the correct ones are enabled for each board. Add a few missing
audio-related GPIOs for Ventana.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update the device tree to indicate which I2C controller is the DVC
controller. AUXDATA needs to be updated too, since the compatible
value changed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the tegra30 based cardhu development board. Cardhu is a tablet
formfactor reference design for tegra30. The patch provides a device tree for
the board, updates Makefile.boot to build the dtb, includes the platform in
Kconfig and updates board-dt.c.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for tegra30 SoC. This includes a device tree compatible type for
this SoC ("nvidia,tegra30") and adds L2 cache initialization for this new SoC.
The clock framework is still missing, which prevents most drivers from working.
The basic IRQs are the same, so remove the dependency on
CONFIG_ARCH_TEGRA_2x_SOC.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Define the pinmuxing and pindrive tables for tegra30. The pinmux table defines
the available functions for each pinmux group. The pindrive table defines the
default pullup or pulldowns for each group.
Derived from code by Scott Williams (scwilliams@nvidia.com)
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add new fields to struct tegra_pingroup_desc to support new hardware features
introduced in the tegra30 SoC. The pinmux driver won't use those fields yet,
but the tegra30 pinmux tables will already provide the necessary data.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch modifies the pinmux code to be useable for multiple tegra variants.
Some tegra20 specific constants will be replaced by variables which will be
initialized to the appropriate value at runtime.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rename pinmux-t2.h and pinmux-t2-tables.c to the new tegra naming. This file
will be reworked somewhat in the next patch to support multiple tegra SoC
types.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Generalize L2 cache initialization and discover L2 cache associativity at
runtime.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use PMC reset rather then CAR system reset as recommended by the hardware
team.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra20 based boards will be handled by the current board-dt.c file. Tegra30
based boards will be handled by a new board-dt-tegra30.c file. Hence rename
the existing board-dt.c to board-dt-tegra20.c to reflect its use.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch splits the early init code in a common and a tegra20 specific part.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
don't export clk_measure_input_freq as its functionality is also available
using clk_get_rate().
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rework the tegra20 clock code to support multiple tegra variants :
* remove tegra2_periph_reset_assert/tegra2_periph_reset_deassert. This
functionality should be in clock.c.
* remove tegra_sdmmc_tap_delay and export tegra2_sdmmc_tap_delay
directly. This feature is handled inside the sdmmc block from tegra30
onwards. So there is no need for support in the clock code beyond
tegra20. There are no in tree users of this function.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* add a dependency to ARCH_TEGRA_2x_SOC in Kconfig to all tegra20 based boards
and TEGRA_PCI
* make powergating dependent on ARCH_TEGRA_2x_SOC
* remove dependency on ARCH_TEGRA_2x_SOC for clock.c
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The timer and rtc-timer clocks aren't gated by default, so there is no reason
to crash the system if the dummy enable call failed.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
entry-macro.S contains some stale code for chips before Tegra20 that
apparently didn't use an ARM GIC. All chips supported by mainline use
an ARM GIC, so rip out the stale code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Convert tegra20 IRQ intialization to the GIC devicetree binding. Modify the
interrupt definitions in the dts files according to
Documentation/devicetree/bindings/arm/gic.txt
v3 (swarren):
* Moved of_irq_init() call into board-dt.c to avoid ifdef'ing it.
- Even with a dummy replacement if !CONFIG_OF, the reference from
tegra_dt_irq_match[] to gic_of_init() would still have to be ifdef'd
- It's plausible that tegra_dt_irq_match[] may need to contain more
entries in the future, and defining what they are seems more suitable
for board-dt.c than irq.c
v2 (swarren):
* Removed some stale GIC init code from board-dt.c
* Undid some accidental 0x -> 0x0 search/replace.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[olof: added include of <asm/hardware/gic.h> for compile to pass]
Signed-off-by: Olof Johansson <olof@lixom.net>
PPI_NR is never used in arch/arm/mach-tegra/irq.c. Remove it.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
For some reason it started out using {} instead of (), and it's
proliferated from there. Switch back to ().
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
This fix updates the CDEV1 pinmux for the paz00 board to be as in the
Harmony board. Paz00 board is originally based on Harmony design.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for a wakeup gpio which is connected to the
embedded controller. This will be used later on for wakeup from suspend.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Certain clocks are required for core audio functionality. Set up the
appropriate parenting relationships, and enable clocks that must be
on permanently.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix the address of the I2S2 controller in the AUXDATA table.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds a dts file for paz00. As a side effect, this also enables
the embedded controller which controls the keyboard, touchpad, power,
leds, and some other functions.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add device-tree file for TrimSlice
* Add that to the list of .dts files to build
* Update board-dt.c to recognize TrimSlice board name
v2: Makefile: Add board-trimslice-pinmux.c to obj-$(CONFIG_MACH_TEGRA_DT).
v3: Makefile: Use brackets not braces around var names
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rely on platform_data being passed through auxdata for now; more elaborate
bindings for phy config and tunings to be added.
v2: moved vbus-gpio check to the helper function, added check for !of_node,
added usb2 clock to board-dt table.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
For some reason it started out using {} instead of (), and it's
proliferated from there. Switch back to ().
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
wm8903_platform_data.gpio_cfg[] was intended to be interpreted as follows:
0: Don't touch this GPIO's configuration register
1..7fff: Write that value to the GPIO's configuration register
8000: Write zero to the GPIO's configuration register
other: Undefined (invalid)
The rationale is that platform data is usually global data, and a value of
zero means that the field wasn't explicitly set to anything (e.g. because
the field was new to the pdata type, and existing users weren't update to
initialize it) and hence the value zero should be ignored. 0x8000 is an
explicit way to get 0 in the register.
The code worked this way until commit 7cfe561 "ASoC: wm8903: Expose GPIOs
through gpiolib", where the behaviour was changed due to my lack of
awareness of the above rationale.
This patch reverts to the intended behaviour, and updates all in-tree users
to use the correct scheme. This also makes WM8903 consistent with other
devices that use a similar scheme.
WM8903_GPIO_NO_CONFIG is also renamed to WM8903_GPIO_CONFIG_ZERO so that
its name accurately reflects its purpose.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that MULTI_IRQ_HANDLER is selected by all the in-tree
GIC users, make it mandatory and remove the unused macros.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Convert the tegra2 platforms to be using the gic_handle_irq
function as their primary interrupt handler.
Tested on harmony.
Cc: Colin Cross <ccross@android.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Enable the headphone detection gpio on tegra platform.
Signed-off-by: Yufeng Shen <miletus@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
*_pinmux_init() register the GPIO and pinmux devices so that they're ready
before any other device needs them.
*_pinmux_init() are also called by board-dt.c in order to set up the GPIO
and pinmux configurations. In this case, if we register the devices, they
end up being probed once due to this registration, and a second time due
to a device-tree node (or vice-versa). The second probe fails since the
memory regions are already requested. Besides, we don't actually want the
duplicated devices.
To avoid this duplicate registration, modify *_pinmux_init() to check
whether it's running on a DT machine. If not, register the pinmux devices.
If so, don't register them.
Finally, modify board-dt.c to call the *_pinmux_init() after all devices have
been instantiated from device-tree. This allows the GPIO and pinmux devices
to be instantiated and initialized before calling functions to configure the
hardware.
This has one disadvantage: The pinmux and GPIO initialization now happens
after /all/ devices are instantiated, rather than after just gpio and
pinmux but before anything else. So the correct HW configuration is not
in place when e.g. the SD/MMC device is probed. Long-term, this should be
solved by doing both:
a) Initializing the HW state from DT nodes during GPIO and pinmux device
probe.
b) Using the deferred driver probe mechanism, so that drivers can defer
their probe until after the gpio and pinmux drivers have probed.
v2: s/int is_dt/bool is_dt/
v3: Use of_machine_is_compatible inside *_pinmux_init() rather than passing
an explicit parameter into the function from outside.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
* 'next/board' of git://git.linaro.org/people/arnd/arm-soc: (34 commits)
ep93xx: add support Vision EP9307 SoM
ARM: mxs: Add initial support for DENX MX28
ARM: EXYNOS4: Add support SMDK4412 Board
ARM: EXYNOS4: Add MCT support for EXYNOS4412
ARM: EXYNOS4: Add functions for gic interrupt handling
ARM: EXYNOS4: Add support clock for EXYNOS4412
ARM: EXYNOS4: Add support new EXYNOS4412 SoC
ARM: EXYNOS4: Add support MCT PPI for EXYNOS4212
ARM: EXYNOS4: Add support PPI in external GIC
ARM: EXYNOS4: convert boot_params to atag_offset
ixp4xx: support omicron ixp425 based boards
ARM: EXYNOS4: Add support SMDK4212 Board
ARM: EXYNOS4: Add support PM for EXYNOS4212
ARM: EXYNOS4: Add support clock for EXYNOS4212
ARM: EXYNOS4: Add support new EXYNOS4212 SoC
at91: USB-A9G20 C01 & C11 board support
at91: merge board USB-A9260 and USB-A9263 together
at91: add support for RSIs EWS board
ARM: SAMSUNG: Fix mask value for S5P64X0 CPU IDs
ARM: SAMSUNG: Fix mask for S3C64xx CPU IDs
...
These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro. So they will need <linux/export.h>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The exynos4 updates conflict with code from the arm devel-stable branch
and new boards need to set atag_offset in place of boot_param.
Conflicts:
arch/arm/Kconfig
arch/arm/mach-exynos4/include/mach/entry-macro.S
arch/arm/mach-exynos4/mach-smdkc210.c
arch/arm/mach-exynos4/mach-smdkv310.c
arch/arm/mach-exynos4/mct.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It is generally a better idea to make intentionally empty files
contain the human-readable /* empty */ comment, also it makes
the files play nice with "make distclean".
Reported-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Rather than clipping the number of CPUs using the compile-time NR_CPUS
constant, use the runtime nr_cpu_ids value instead. This allows the
nr_cpus command line option to work as expected.
Cc: <stable@kernel.org>
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of the mdesc pointer in the fixup function call. No one uses
the mdesc pointer, it shouldn't be modified anyway, and we can't wrap
it, so let's remove it.
Platform files found by:
$ regexp=$(git grep -h '\.fixup.*=' arch/arm |
sed 's!.*= *\([^,]*\),* *!\1!' | sort -u |
tr '\n' '|' | sed 's,|$,,;s,|,\\|,g')
$ git grep $regexp arch/arm
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Boards used to specify zreladdr in their Makefile.boot with
zreladdr-y := x, so conflicting zreladdrs were silently overwritten.
This patch changes this to zreladdr-y += x, so that we end
up with multiple words in zreladdr in such a case. We can
detect this later and complain if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Without this, the PMC continually detects an interrupt when the PMU_IRQ
line is high, causing the tps6686x IRQ handler thread to hog an entire
CPU.
This change was originally written by Wei Ni <wni@nvidia.com> for Seaboard
in the ChromeOS kernel.
Long-term, this should probably be moved into some kind of PMU driver,
or perhaps integrated into the GPIO/IRQ/pinmux system?
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for ventana pinmuxing as a seaboard derivative. This is a cut down
version of work done by Jong Kim <jongk@nvidia.com>.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch splits out the common part of pinmux and GPIO initialization for
seaboard and derived boards. This code is based on work done by Jong Kim
<jongk@nvidia.com>.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use ioremap to obtain access to registers instead of using static
mappings. This reduces the number of users of the static mappings, which
will eventually allow them to be removed.
Note that on Tegra30, the number of register "banks" will decrease to 2,
and the packing of specific bits into registers will change significantly.
That's why this change adds the "*_bank" fields to the pingroup tables,
rather than implementing some more hard-coded scheme.
Also, completely remove the implementation of suspend/resume; Tegra doesn't
yet support suspend/resume, and the implementation is complex for the
general pinmux driver:
* Not all registers are used within each bank, so we probably shouldn't
just iterate over every register in the bank, and save/restore it,
since that would mean touching undefined registers.
* Registers are shared between pingroups, so we can't simply iterate over
each pingroup, and save/restore the registers it uses.
It'd probably be best have probe() calculate a bitmask of actually-used
registers for each bank, and have suspend/resume iterate over those
bitmaps.
Oh, and Real Soon Now, I should be looking into converting this driver to
the new pinmux/pinctrl subsystem, so I didn't want to put too much work
into the current incarnation.
v2: s/space/bank/ to match comments on reg_* fields in pinmux.h.
Re-order bank/reg parameters to pg_readl/pg_writel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Resolves lots of sparse warnings:
arch/arm/mach-tegra/devices.c:102:24: warning: symbol 'tegra_i2c_device1' was not declared. Should it be static?
arch/arm/mach-tegra/devices.c:112:24: warning: symbol 'tegra_i2c_device2' was not declared. Should it be static?
arch/arm/mach-tegra/devices.c:122:24: warning: symbol 'tegra_i2c_device3' was not declared. Should it be static?
arch/arm/mach-tegra/devices.c:132:24: warning: symbol 'tegra_i2c_device4' was not declared. Should it be static?
[...]
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Two static functions that are not exported:
arch/arm/mach-tegra/cpu-tegra.c:59:5: warning: symbol 'tegra_verify_speed' was not declared. Should it be static?
arch/arm/mach-tegra/cpu-tegra.c:64:14: warning: symbol 'tegra_getspeed' was not declared. Should it be static?
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Type fix:
arch/arm/mach-tegra/cpu-tegra.c:144:14: warning: incorrect type in argument 5 (different signedness)
arch/arm/mach-tegra/cpu-tegra.c:144:14: expected unsigned int *index
arch/arm/mach-tegra/cpu-tegra.c:144:14: got int *<noident>
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
None of them are used externally.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Not used externally, and certainly don't need to be exported.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Not exported and not used externally.
Also, fix return type. Due to new return type, errors can't be returned
so WARN_ON instead of returning error if a bad parameter is specified.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Not exported and not used externally.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Not exported and not used externally.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
arch/arm/mach-tegra/pcie.c:908:12: warning: symbol 'tegra_pcie_init' was not declared. Should it be static?
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes a lot of:
arch/arm/mach-tegra/pcie.c:678:8: warning: cast removes address space of expression
arch/arm/mach-tegra/pcie.c:678:8: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-tegra/pcie.c:678:8: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-tegra/pcie.c:678:8: got unsigned int
arch/arm/mach-tegra/pcie.c:678:8: warning: cast removes address space of expression
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes a lot of:
arch/arm/mach-tegra/tegra2_clocks.c:921:34: warning: Using plain integer as NULL pointer
arch/arm/mach-tegra/tegra2_clocks.c:1462:4: warning: Using plain integer as NULL pointer
arch/arm/mach-tegra/tegra2_clocks.c:1864:4: warning: Using plain integer as NULL pointer
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes a lot of:
arch/arm/mach-tegra/tegra2_clocks.c:180:2: warning: cast removes address space of expression
arch/arm/mach-tegra/tegra2_clocks.c:180:2: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-tegra/tegra2_clocks.c:180:2: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-tegra/tegra2_clocks.c:180:2: got unsigned int
arch/arm/mach-tegra/tegra2_clocks.c:180:2: warning: cast removes address space of expression
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fixes a lot of:
arch/arm/mach-tegra/timer.c:75:2: warning: cast removes address space of expression
arch/arm/mach-tegra/timer.c:75:2: warning: incorrect type in argument 1 (different base types)
arch/arm/mach-tegra/timer.c:75:2: expected void const volatile [noderef] <asn:2>*<noident>
arch/arm/mach-tegra/timer.c:75:2: got unsigned int
arch/arm/mach-tegra/timer.c:75:2: warning: cast removes address space of expression
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Provide __iomem annotation for IO_*_VIRT pointers, which will propagate
up through IO_TO_VIRT(). Also fixes a 0 to NULL conversion of the base
case to silence sparse.
Unfortunately map_desc takes an unsigned long for the pointer instead of
a void __iomem *. For now, cast explicitly for those cases.
v2: change define to use IOMEM() like many other mach platforms per
comment from Russell.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The Tegra GPIO driver will be converted from static registration via
postcore_initcall() to be a platform device later in this patch series.
A new Tegra pinmux platform device will also be added.
Prepare for this by modifying all boards to register the appropriate
platform devices before-hand, so that when the drivers are converted,
those devices will be probed, and git bisectability will be maintained.
v2: Add resource definitions for GPIO and pinmux
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This fixes a compilation error in cpu-tegra.c which was introduced in
dc8d966bcc ("ARM: convert PCI defines to variables") which removed the
now obsolete mach/hardware.h from the mach-tegra subtree.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will eventually allow <mach/gpio.h> to be deleted. This mirrors
LinusW's recent equivalent work on various other ARM platforms.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms (like OMAP not to name it) are doing rather complicated
hacks just to determine the base UART address to use. Let's give their
addruart macro some slack by providing an extra work register which will
allow for much needed cleanups.
This is basically a no-op as this commit is only adding the extra argument
to the macro but no one is using it yet.
Signed-off-by: nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>
This centralizes all GPIO naming in one header.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tegra's <mach/gpio.h> uses type bool; we need to include <linux/types.h>
to get the definition.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By not definining a custom gpio_to_irq, the default gpiolib version is
used, allowing platform consolidation.
irq_to_gpio is deprecated and in the process of being removed. Make that
happen now for ARM Tegra.
This also partially fixes the Tegra build; it was broken because gpio.h
referred to EINVAL, which wasn't always defined when <mach/gpio.h> was
included.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead. This means that by default, you get the trivial implementation
and only have to do something extra if you need to. This should
encourage the use of the trivial default implementation.
As an additional bonus, several gpio.h header files become empty.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many of the gpio_to_irq implementations use the gpiolib version of this
function. Provide the standard gpiolib gpio_to_irq() for everyone, but
allow platforms to override it if they wish. Add the neccessary
overrides for those platforms which do not use the standard definition.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate 24 trivial gpiolib implementions out of mach/gpio.h
into asm/gpio.h. This is basically the include of asm-generic/gpio.h
and the definition of gpio_get_value, gpio_set_value, and gpio_cansleep
as described in Documentation/gpio.txt
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: David Brown <davidb@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These clocks are required for usb operation. pll_p_out4 needs to be set
to 24 MHz. The other clocks default to "off" in order to save some energy.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
8250.c recently gained an explicit PORT_TEGRA port type. Specifically
request this in all Tegra boards' UART platform data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This reorders the SDHCI channel init order. With this patch, the
internal emmc gets the mmcblk0 device while the external sdmmc port
gets mmcblk1. This change is only for convenience.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for the wifi led. It is automaticly triggered by
the rfkill0 event.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for controlling the rfkill gpios for the
internal WIFI card via the rfkill_gpio driver.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
UART-A is connected to JP1 and used by the bootloader for debugging
output while UART-D is connected to the mini-pcie expansion slot.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Seaboard has a couple of external USB ports. Add the platform devices and
GPIO infra-structure to enable these.
I tested both ports with a mouse on Seaboard non-clamshell.
This change is extracted from code in the ChromeOS 2.6.38 kernel.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Initialize clock tree for audio
* Add GPIO base definitions
* Add audio GPIO definitions
* Define platform data for WM8903 and ASoC machine driver
* Add special case for Kaen to handle HP_MUTE GPIO
* Register platform devices for audio
* Update pinmux to cater for new GPIOs used for audio
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra USB port is attached an an SMSC9514; a combination USB hub
and Ethernet controller.
This change is extracted from a change in the ChromeOS 2.6.38 kernel.
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
* 'next/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (21 commits)
arm/dt: tegra devicetree support
arm/versatile: Add device tree support
dt/irq: add irq_domain_generate_simple() helper
irq: add irq_domain translation infrastructure
dmaengine: imx-sdma: add device tree probe support
dmaengine: imx-sdma: sdma_get_firmware does not need to copy fw_name
dmaengine: imx-sdma: use platform_device_id to identify sdma version
mmc: sdhci-esdhc-imx: add device tree probe support
mmc: sdhci-pltfm: dt device does not pass parent to sdhci_alloc_host
mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()
mmc: sdhci-esdhc-imx: do not reference platform data after probe
mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5
net/fec: add device tree probe support
net: ibm_newemac: convert it to use of_get_phy_mode
dt/net: add helper function of_get_phy_mode
net/fec: gasket needs to be enabled for some i.mx
serial/imx: add device tree probe support
serial/imx: get rid of the uses of cpu_is_mx1()
arm/dt: Add dtb make rule
arm/dt: Add skeleton dtsi file
...
Everything required to populate NVIDIA Tegra devices from the device
tree. This patch adds a new DT_MACHINE_DESC() which matches against
a tegra20 device tree. So far it only registers the on-chip devices,
but it will be refined in follow on patches to configure clocks and
pin IO from the device tree also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
Aside of the usual motivation for constification, this function has a
history of being abused a hook for interrupt and other fixups so I turned
this function const ages ago in the MIPS code but it should be done
treewide.
Due to function pointer passing in varous places a few other functions
had to be constified as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To: Anton Vorontsov <avorontsov@mvista.com>
To: Chris Metcalf <cmetcalf@tilera.com>
To: Colin Cross <ccross@android.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
To: Eric Miao <eric.y.miao@gmail.com>
To: Erik Gilling <konkers@android.com>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
To: "H. Peter Anvin" <hpa@zytor.com>
To: Imre Kaloz <kaloz@openwrt.org>
To: Ingo Molnar <mingo@redhat.com>
To: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
To: Jesse Barnes <jbarnes@virtuousgeek.org>
To: Krzysztof Halasa <khc@pm.waw.pl>
To: Lennert Buytenhek <kernel@wantstofly.org>
To: Matt Turner <mattst88@gmail.com>
To: Nicolas Pitre <nico@fluxnic.net>
To: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
To: Richard Henderson <rth@twiddle.net>
To: Russell King <linux@arm.linux.org.uk>
To: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-alpha@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-pci@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Cc: x86@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Bus number 4 doesn't exist in the mainline kernel. The device is
attached to bus number 3. (In the ChromeOS kernel, one of the I2C
busses is split in two with a mux, this pushing all later busses
to a higher bus number. In this case, 4 is the correct bus number
for the ADT7461).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
DAP3 is used for a bunch of GPIOs. Not tri-stating the pins means audio
signals get sent out there, and this ends up resetting USB and breaking
SDHCI too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
trimslice and paz00 both have functionally identical platform
data for the tegra-ehci driver. Move the platform data into
devices.c, and remove it from all the board files.
Signed-off-by: Colin Cross <ccross@android.com>
Tested-by: Konstantin Sinyuk <kostyas@compulab.co.il>
Acked-by: Olof Johansson <olof@lixom.net>
Every board file includes the same platform data definition
for the i2c-tegra driver's bus speed. Move the platform data
into devices.c, and remove it from all the board files.
Signed-off-by: Colin Cross <ccross@android.com>
Tested-by: Konstantin Sinyuk <kostyas@compulab.co.il>
Acked-by: Olof Johansson <olof@lixom.net>
cpu_set() is marked as obsolete cpumask function and we plan to
remove it in future.
This patch replace it with modern cpumask function.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-tegra@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Colin Cross <ccross@android.com>
Although disp1 and disp2 have 7.1 divisors, their corresponding
registers in the clk_rst block are not the interface to program the
divisors. Setting the generic DIV_U71 flag may cause the code to
attempt to program the clock at a different divisor, which will confuse
any code attempting to use that clock since it isn't actually being
divided.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
This renames "paz00" in MACHINE_START macro to a neater string.
PAZ00 seems to have been the Compal internal project name, while
PROCYON looks like Toshiba project name.
Anyway, the AC100 support package in Ubuntu needs the new naming to
identify the machine.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Colin Cross <ccross@android.com>
The internal storage has no gpios connected to. Also the second
port is not connected at all, so remove it from the board file.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Colin Cross <ccross@android.com>
This patch add support for the second and third ehci bus on paz00.
The first bus needs gadget and nvec support and will be added once
the needed patches are upstream.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Colin Cross <ccross@android.com>
This adds support for the i2c busses on paz00. The 3rd bus is
reserved for the nvec, which acts as master and i2c-tegra has
not yet support for this kind of operation.
The sound codec (alc5632) is connected to the first bus and will
be added once the codec and glue driver is upstream.
The thermal sensor (atd7461) is connected to dvc as usual, but will
not be added now because i2c-tegra still misses probe support
(needs I2C_FUNC_SMBUS_EMUL).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Colin Cross <ccross@android.com>
This patch replaces long sequences of spaces by tabs and tabs by
spaces were appropriate.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Colin Cross <ccross@android.com>
The barriers implemented in arch/arm/mach-tegra/mach/barriers.h
are exactly the same as the default barriers implemented in
arch/arm/include/asm/system.h. Remove barriers.h from Tegra,
and don't select ARCH_HAS_BARRIERS.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Ensure the built-in eMMC is always named mmcblk0.
This is important because:
* U-Boot statically assigns MMC device IDs based on controller ID.
* U-Boot assumes that kernel MMC device ID numbering matches U-Boot numbering.
* U-Boot provides a kernel cmdline option e.g. root=/dev/mmcblk0p3 based on
that numbering.
* The kernel dynamically assigns MMC device IDs based on enumeration order of
the memory behind the host controller, rather than statically based on host
controller ID like U-Boot.
* By registering the SDHCI controller for the built-in eMMC first, the
enumeration of the built-in eMMC is performed first, and hence eMMC gets
assigned ID 0 just like U-Boot. If the SD slot is filled, it then gets
assigned ID 1 just like U-Boot.
* If the MMC IDs mismatch, and the system boots from SD card not eMMC, the
kernel will access the eMMC instead of SD card when attempting to mount
/dev/mmcblk1p3 as the root fs. If eMMC is not partitioned/formatted, the
kernel will panic since the root fs can't be mounted. If eMMC is partitioned
and formatted, the kernel will mount an unexpected filesystem as the root fs.
This change relies on the SDHCI driver performing initial card detection
synchronously during device registration. This is currently the case.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Rob Herring
Stephen Warren
Arnd Bergmann
Peter De Schrijver
Olof Johansson
Greg Kroah-Hartman
Heikki Krogerus
Thierry Reding
Bjorn Helgaas
Russell King
Marc Dietrich
Laxman Dewangan
Doug Anderson
Shridhar Rasal
Hiroshi DOYU
Rakesh Iyer
Nicolas Pitre
Henning Heinold
Linus Torvalds
Marc Zyngier
Mark Brown
Leon Romanovsky
Yufeng Shen
Paul Gortmaker
Linus Walleij
Sascha Hauer
Marc Dietrich
Grant Likely
Uwe Kleine-König
Ralf Baechle
Al Viro
Kyungmin Park
Colin Cross
Mike Rapoport
KOSAKI Motohiro
Robert Morell