Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the readl() kernel function to read all index registers. For ARM
systems, this function includes a read memory barrier that eliminates ci/pi
corruption.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Tested-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for these new device IDs:
Advantech MIC-8312BridgeB
INSPUR PM8204-2GB
INSPUR PM8204-4GB
INSPUR PM8222-SHBA
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detect rare error cases for synchronous requests down the RAID path.
Also retry INQUIRY of VPD page 0 sent to an HBA drive if the command failed
due to an abort.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Decrement the active thread count after the synchronous request was
submitted to the controller but before the driver blocks to wait for the
request to complete.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoids that warnings about the kernel headers appear when building with
W=1. Remove useless "@Returns - Nothing" clauses. Change "@Return - " into
"Return: ".
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Split each of these functions in three functions - one function per reset
phase. This patch does not change any functionality but makes the code
easier to read.
Note: it is much easier to review the git diff -w output after having
applied this patch than by reviewing the patch itself.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since ioc->shost_recovery is set after ioc->reset_in_progress_mutex is
obtained, if concurrent resets are issued there is a short time during
which ioc->reset_in_progress_mutex is locked and ioc->shost_recovery ==
0. Avoid that this can cause trouble by unconditionally locking
ioc->shost_recovery.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that smatch complains about a double unlock on
ioc->transport_cmds.mutex.
Fixes: 651a013649 ("scsi: scsi_transport_sas: switch to bsg-lib for SMP passthrough")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make _base_build_nvme_prp() easier to read by introducing a structure
to access NVMe command fields.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch avoids that gcc complains about switch/case fall-through
when building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify the indentation such that smatch no longer complains about
inconsistent indenting.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 2623c7a5f2 ("libata: add refcounting to ata_host") v4.17+ introduced
refcounting to ata_host and will increase or decrease the refcount when
adding or deleting transport ATA port.
Now the ata host for libsas is embedded in domain_device, and the ->kref
member is not initialized. Afer we add ata transport class, ata_host_get()
will be called when adding transport ATA port and a warning will be
triggered as below:
refcount_t: increment on 0; use-after-free.
WARNING: CPU: 2 PID: 103 at
lib/refcount.c:153 refcount_inc+0x40/0x48 ...... Call trace:
refcount_inc+0x40/0x48
ata_host_get+0x10/0x18
ata_tport_add+0x40/0x120
ata_sas_tport_add+0xc/0x14
sas_ata_init+0x7c/0xc8
sas_discover_domain+0x380/0x53c
process_one_work+0x12c/0x288
worker_thread+0x58/0x3f0
kthread+0xfc/0x128
ret_from_fork+0x10/0x18
And also when removing transport ATA port ata_host_put() will be called and
another similar warning will be triggered. If the refcount decreased to
zero, the ata host will be freed. But this ata host is only part of
domain_device, it cannot be freed directly.
So we have to change this embedded static ata host to a dynamically
allocated ata host and initialize the ->kref member. To use ata_host_get()
and ata_host_put() in libsas, we need to move the declaration of these
functions to the public libata.h and export them.
Fixes: b6240a4df0 ("scsi: libsas: add transport class for ATA devices")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Taras Kondratiuk <takondra@cisco.com>
CC: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With its one user gone, remove the library code.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sbitmap and the percpu_ida perform essentially the same task,
allocating tags for commands. The sbitmap outperforms the percpu_ida as
documented here: https://lkml.org/lkml/2014/4/22/553
The sbitmap interface is a little harder to use, but being able to remove
the percpu_ida code and getting better performance justifies the additional
complexity.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> # f_tcm
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce target_free_tag() and convert all drivers to use it.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ufshcd_dump_regs should use memcpy_fromio to read host registers
instead of directly accessing using memcpy. The same function is
utilized in ufs-qcom.
Elminite compilation warning
drivers/scsi/ufs/ufshcd.c:356:9: warning: incorrect type in argument 6 (different address spaces)
drivers/scsi/ufs/ufshcd.c:356:9: expected void const *buf
drivers/scsi/ufs/ufshcd.c:356:9: got void [noderef] <asn:2>*mmio_base
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit a45b599ad8 ("scsi: sg: allocate with __GFP_ZERO in
sg_build_indirect()") changed the call to alloc_pages to always use
__GFP_ZERO. Just above that, though, there was this:
if (!capable(CAP_SYS_ADMIN) || !capable(CAP_SYS_RAWIO))
gfp_mask |= __GFP_ZERO;
And there's only one user of the gfp_mask. Just or in the __GFP_ZERO
flag at the top of the function and be done with it.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit d2ba5675d8 ("[SCSI] qla2xxx: Disable local-interrupts while
polling for RISC status.") added a local_irq_disable() before invoking the
->intr_handler callback. The function, which was used in this callback, did
not disable interrupts while acquiring the spin_lock so a deadlock was
possible and this change was one possible solution.
The function in question was qla2300_intr_handler() and is using
spin_lock_irqsave() since commit 43fac4d97a ("[SCSI] qla2xxx: Resolve a
performance issue in interrupt"). I checked all other ->intr_handler
callbacks and all of them use the irqsave variant so it is safe to remove
the local_irq_save() block now.
Cc: qla2xxx-upstream@qlogic.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This will make subsequent refactoring easier to handle.
Note: this patch is nowhere checkpatch clean.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When ioremap_nocache fails, the lack of error-handling code may cause
unexpected results.
This patch adds error-handling code after calling ioremap_nocache.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit 312d3e5611 ("[SCSI] libsas: remove ata_port.lock management
duties from lldds") the sas_ata_qc_issue() function unlocks the
ata_port.lock and disables interrupts before doing so. That lock is always
taken with disabled interrupts so at this point, the interrupts are already
disabled. There is no need to disable the interrupts before the unlock
operation because they are already disabled. Restoring the interrupt state
later does not change anything because they were disabled and remain
disabled. Therefore remove the operations which do not change the
behaviour.
Fixes: 312d3e5611 ("[SCSI] libsas: remove ata_port.lock management duties from lldds")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds formatting error overlay 0x41 to improve debug
capabilities.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update CFG_1US_TIMER_TRSH and CON_CFG_DRIVER settings.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The init is missed for hisi_sas_phy spinlock, so add it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver spends much time allocating and freeing the slot DMA
buffer for command delivery/completion. To boost the performance,
pre-allocate the buffers for all IPTT. The downside of this approach is
that we are reallocating all buffer memory upfront, so hog memory which we
may not need.
However, the current method - DMA buffer pool - also caches all buffers and
does not free them until the pool is destroyed, so is not exactly efficient
either.
On top of this, since the slot DMA buffer is slightly bigger than a 4K
page, we need to allocate 2x4K pages per buffer (for 4K page kernel), which
is quite wasteful. For 64K page size this is not such an issue.
So, for the 4K page case, in order to make memory usage more efficient,
pre-allocating larger blocks of DMA memory for the buffers can be more
efficient.
To make DMA memory usage most efficient, we would choose a single
contiguous DMA memory block, but this could use up all the DMA memory in
the system (when CMA enabled and no IOMMU), or we may just not be able to
allocate a DMA buffer large enough when no CMA or IOMMU.
To decide the block size we use the LCM (least common multiple) of the
buffer size and the page size. We roundup(64) to ensure the LCM is not too
large, even though a little memory may be wasted per block.
So, with this, the total memory requirement is about is about 17MB for 4096
max IPTT.
Previously (for 4K pages case), it would be 32MB (for all slots
allocated).
With this change, the relative increase of IOPS for bs=4K read when
PAGE_SIZE=4K and PAGE_SIZE=64K is as follows:
IODEPTH 4K PAGE_SIZE 64K PAGE_SIZE
32 56% 47%
64 53% 44%
128 64% 43%
256 67% 45%
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In host reset, we use TMF or soft-reset to re-init device, and if success,
we will release all LLDD resources of this device. If the init fails -
maybe because the device was removed or link has not come up - then do not
release the LLDD resources, but rather rely on SCSI EH to handle the
timeout for these resources later on.
But if clear nexus ha calls host reset, which is the last effort of SCSI
EH, we should release all LLDD remain resources. Because SCSI EH will
release all tasks after clear nexus ha.
Before release, we do I_T nexus reset to try to clear target remain IOs.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During reset, we don't want PHY events reported to libsas for PHYs which
were previously attached prior to reset.
So check hisi_hba->flags for HISI_SAS_RESET_BIT to filter PHY events during
reset.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After soft_reset() for host reset, we should not be allowed to send
commands to the HW before the PHYs have come up and the port ids have been
refreshed.
Prior to this point, any commands cannot be successfully completed.
This exclusion is achieved by grabbing the host reset semaphore.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a possible conflict when a device is removed and host reset occurs
concurrently.
The reason is that then the device is notified as gone, we try to clear the
ITCT, which is notified via an interrupt. The dev gone function pends on
this event with a completion, which is completed when the ITCT interrupt
occurs.
But host reset will disable all interrupts, the wait_for_completion() may
wait indefinitely.
This patch adds an semaphore to synchronise this two processes. The
semaphore is taken by the host reset as the basis of synchronising.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are many BROADCAST primitives generated by the host. We are only
interested in BROADCAST (CHANGE) primitives currently, so only process
this.
We have applied this processing for v2 hw before, and it is also needed for
v3 hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch replaces the usage of dma_alloc_coherent() with the managed
version, dmam_alloc_coherent(), hereby reducing replicated code.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by; John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware provides drive specific target reset and task abort timeout
values. Driver needs to use these timeout values during task management
calls. If FW does not provide these values, fall back to using earlier
default timeout of 50 seconds for TM.
[mkp: clarified comment]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While driver is waiting for adapter to become operational, if a kill
adapter is issued, driver can bail out from the wait loop immediately
rather than waiting for the entire 180 seconds.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a possibility that firmware on the controller was upgraded before
system was suspended. During resume, driver needs to read updated
controller properties.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If MR_DCMD_CTRL_GET_INFO DCMD timed out, return failure rather than doing
kill adapter.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated driver version to "26.100.00.00"
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Presently driver is using combined reply queue feature when MSI-x vectors >
8 for both SAS3 and SAS3.5 controllers. But as per MPI-spec,
1. For SAS3 controllers, driver should use combined reply queue when HBA
supports more than 8 MSI-x vectors.
2. For SAS3.5 controllers, driver should use combined reply queue when HBA
supports more than 16 MSI-x vectors.
Modified driver code to use combined reply queue for SAS3 controllers when
HBA supports > 8 MSI-x vectors and for SAS3.5 controllers when HBA supports
> 16 MSI-x vectors.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an ioctl is sent to FW, and if there is a controller reset issued
before ioctl gets completed, then in controller reset path all the pending
ioctl commands are terminated from "mpt3sas_ctl_reset_handler" function.
This will wake up the waiting ioctl commands in ioctl path and print
timeouts which are actually not timeouts.
Introduced "mpt3sas_base_check_cmd_timeout" function to check and print
whether command got timed out (or) terminated due to Host reset.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While configuring of NVMe device handling, _pcie_device structure member
was accessed after its reference count is decremented/put. Hence modified
code to access member of _pcie_device structure before its reference count
is decremented/put.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _scsih_scan_finished driver should mark port_enable_cmd.status as
'command not used', instead base_cmds.status was marked as 'command not
used'. Update code to mark port_enable_cmd.status as 'command not used'.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Linux driver when receives Broadcast Asynchronous Event Notification (BAEN)
from the controller firmware, checks all pending I/Os at the driver level
and issues query task, abort task TMs. This is done in the driver to handle
drives which are connected with multiple initiators and undergoing target
resets. In the BAEN handling code, the I/Os issued to NVMe drives are also
handled and query task and abort task TMs are issued, which are not
necessary as there is no multi-initiator and no BAEN concept with NVMe
drives. Hence when the driver checks for pending I/Os it skips NVMe drives
at this moment.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the TCMU_RING_SIZE macro is not using here will discard it and at the
same time clean up the code style.
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Acked-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----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=gyaY
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180616' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes that should go into -rc1. This contains:
- bsg_open vs bsg_unregister race fix (Anatoliy)
- NVMe pull request from Christoph, with fixes for regressions in
this window, FC connect/reconnect path code unification, and a
trace point addition.
- timeout fix (Christoph)
- remove a few unused functions (Christoph)
- blk-mq tag_set reinit fix (Roman)"
* tag 'for-linus-20180616' of git://git.kernel.dk/linux-block:
bsg: fix race of bsg_open and bsg_unregister
block: remov blk_queue_invalidate_tags
nvme-fabrics: fix and refine state checks in __nvmf_check_ready
nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
nvme-fabrics: refactor queue ready check
blk-mq: remove blk_mq_tagset_iter
nvme: remove nvme_reinit_tagset
nvme-fc: fix nulling of queue data on reconnect
nvme-fc: remove reinit_request routine
blk-mq: don't time out requests again that are in the timeout handler
nvme-fc: change controllers first connect to use reconnect path
nvme: don't rely on the changed namespace list log
nvmet: free smart-log buffer after use
nvme-rdma: fix error flow during mapping request data
nvme: add bio remapping tracepoint
nvme: fix NULL pointer dereference in nvme_init_subsystem
blk-mq: reinit q->tag_set_list entry only after grace period
- can.rst: fix a footnote reference;
- crypto_engine.rst: Fix two parsing warnings;
- Fix a lot of broken references to Documentation/*;
- Improves the scripts/documentation-file-ref-check script,
in order to help detecting/fixing broken references,
preventing false-positives.
After this patch series, only 33 broken references to doc files are
detected by scripts/documentation-file-ref-check.
-----BEGIN PGP SIGNATURE-----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=/ozx
-----END PGP SIGNATURE-----
Merge tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental
Pull documentation fixes from Mauro Carvalho Chehab:
"This solves a series of broken links for files under Documentation,
and improves a script meant to detect such broken links (see
scripts/documentation-file-ref-check).
The changes on this series are:
- can.rst: fix a footnote reference;
- crypto_engine.rst: Fix two parsing warnings;
- Fix a lot of broken references to Documentation/*;
- improve the scripts/documentation-file-ref-check script, in order
to help detecting/fixing broken references, preventing
false-positives.
After this patch series, only 33 broken references to doc files are
detected by scripts/documentation-file-ref-check"
* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
fix a series of Documentation/ broken file name references
Documentation: rstFlatTable.py: fix a broken reference
ABI: sysfs-devices-system-cpu: remove a broken reference
devicetree: fix a series of wrong file references
devicetree: fix name of pinctrl-bindings.txt
devicetree: fix some bindings file names
MAINTAINERS: fix location of DT npcm files
MAINTAINERS: fix location of some display DT bindings
kernel-parameters.txt: fix pointers to sound parameters
bindings: nvmem/zii: Fix location of nvmem.txt
docs: Fix more broken references
scripts/documentation-file-ref-check: check tools/*/Documentation
scripts/documentation-file-ref-check: get rid of false-positives
scripts/documentation-file-ref-check: hint: dash or underline
scripts/documentation-file-ref-check: add a fix logic for DT
scripts/documentation-file-ref-check: accept more wildcards at filenames
scripts/documentation-file-ref-check: fix help message
media: max2175: fix location of driver's companion documentation
media: v4l: fix broken video4linux docs locations
media: dvb: point to the location of the old README.dvb-usb file
...