Return proper errors for a lot of IPMI failure cases. Also call
pci_disable_device when IPMI PCI devices are removed.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Loading ipmi_si module while bmc is disconnected, we found the timeout
is longer than 5 secs. Actually it takes about 3 mins and 20
secs.(HZ=250)
error message as below:
Dec 12 19:08:59 linux kernel: IPMI BT: timeout in RD_WAIT [ ] 1 retries left
Dec 12 19:08:59 linux kernel: BT: write 4 bytes seq=0x01 03 18 00 01
[...]
Dec 12 19:12:19 linux kernel: IPMI BT: timeout in RD_WAIT [ ]
Dec 12 19:12:19 linux kernel: failed 2 retries, sending error response
Dec 12 19:12:19 linux kernel: IPMI: BT reset (takes 5 secs)
Dec 12 19:12:19 linux kernel: IPMI BT: flag reset [ ]
Function wait_for_msg_done() use schedule_timeout_uninterruptible(1) to
sleep 1 tick, so we should subtract jiffies_to_usecs(1) instead of 100
usecs from timeout.
Reported-by: Hu Shiyuan <hushiyuan@huawei.com>
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use USEC_PER_SEC instead of 1000000, that making the later bugfix
more clearly.
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A respun version of the merges for the pull request previously sent with
a few additional fixes. The last two merges were fixed up by hand since
the branches have moved on and currently have the prior merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller.
- Fix duplicate device registration for ACPI.
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends).
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer.
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CbUw
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A respun version of the merges for the pull request previously sent
with a few additional fixes. The last two merges were fixed up by
hand since the branches have moved on and currently have the prior
merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller
- Fix duplicate device registration for ACPI
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends)
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers"
* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
spi: core: Fix transfer failure when master->transfer_one returns positive value
spi: Correct set_cs() documentation
spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
spi: Spelling s/finised/finished/
spi: sc18is602: Convert to use bits_per_word_mask
spi: Remove duplicate code to set default bits_per_word setting
spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
spi: clps711x: Add MODULE_ALIAS to support module auto-loading
spi: rspi: Add missing clk_disable() calls in error and cleanup paths
spi: rspi: Spelling s/transmition/transmission/
spi: rspi: Add support for specifying CPHA/CPOL
spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
spi: rspi: Add more QSPI register documentation
spi: rspi: Add more RSPI register documentation
spi: rspi: Remove dependency on DMAE for SHMOBILE
spi/s3c64xx: Correct indentation
spi: sh: Use spi_sh_clear_bit() instead of open-coded
spi: bitbang: Grammar s/make to make/to make/
spi: sh-hspi: Spelling s/recive/receive/
spi: core: Improve tx/rx_nbits check comments
...
A respin of the merges in the previous pull request with one extra fix.
A quiet release for the regulator API, quite a large number of small
improvements all over but other than the addition of new drivers for the
AS3722 and MAX14577 there is nothing of substantial non-local impact.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1NsR
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A respin of the merges in the previous pull request with one extra
fix.
A quiet release for the regulator API, quite a large number of small
improvements all over but other than the addition of new drivers for
the AS3722 and MAX14577 there is nothing of substantial non-local
impact"
* tag 'regulator-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (47 commits)
regulator: pfuze100-regulator: Improve dev_info() message
regulator: pfuze100-regulator: Fix some checkpatch complaints
regulator: twl: Fix checkpatch issue
regulator: core: Fix checkpatch issue
regulator: anatop-regulator: Remove unneeded memset()
regulator: s5m8767: Update LDO index in s5m8767-regulator.txt
regulator: as3722: set enable time for SD0/1/6
regulator: as3722: detect SD0 low-voltage mode
regulator: tps62360: Fix up a pointer-integer size mismatch warning
regulator: anatop-regulator: Remove unneeded kstrdup()
regulator: act8865: Fix build error when !OF
regulator: act8865: register all regulators regardless of how many are used
regulator: wm831x-dcdc: Remove unneeded 'err' label
regulator: anatop-regulator: Add MODULE_ALIAS()
regulator: act8865: fix incorrect devm_kzalloc for act8865
regulator: act8865: Remove set_suspend_[en|dis]able implementation
regulator: act8865: Remove unneeded regulator_unregister() calls
regulator: s2mps11: Clean up redundant code
regulator: tps65910: Simplify setting enable_mask for regulators
regulator: act8865: add device tree binding doc
...
Nothing terribly exciting with regmap this release, mainly a few small
extensions to allow more devices to be supported:
- Allow the bulk I/O APIs to be used with no-bus regmaps.
- Support interrupt controllers with zero ack base.
- Warning and spelling fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iPRC
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Nothing terribly exciting with regmap this release, mainly a few small
extensions to allow more devices to be supported:
- Allow the bulk I/O APIs to be used with no-bus regmaps
- Support interrupt controllers with zero ack base
- Warning and spelling fixes"
* tag 'regmap-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix a couple of typos
regmap: Allow regmap_bulk_write() to work for "no-bus" regmaps
regmap: Allow regmap_bulk_read() to work for "no-bus" regmaps
regmap: irq: Allow using zero value for ack_base
regmap: Fix 'ret' would return an uninitialized value
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JT1d
-----END PGP SIGNATURE-----
Merge tag 'xtensa-next-20140123' of git://github.com/czankel/xtensa-linux
Pull Xtensa patches from Chris Zankel:
"The major changes are adding support for SMP for Xtensa, fixing and
cleaning up the ISS (simulator) network driver, and better support for
device trees"
* tag 'xtensa-next-20140123' of git://github.com/czankel/xtensa-linux: (40 commits)
xtensa: implement ndelay
xtensa: clean up udelay
xtensa: enable HAVE_PERF_EVENTS
xtensa: remap io area defined in device tree
xtensa: support default device tree buses
xtensa: initialize device tree clock sources
xtensa: xtfpga: fix definitions of platform devices
xtensa: standardize devicetree cpu compatible strings
xtensa: avoid duplicate of IO range definitions
xtensa: fix ATOMCTL register documentation
xtensa: Enable irqs after cpu is set online
xtensa: ISS: raise network polling rate to 10 times/sec
xtensa: remove unused XTENSA_ISS_NETWORK Kconfig parameter
xtensa: ISS: avoid simple_strtoul usage
xtensa: Switch to sched_clock_register()
xtensa: implement CPU hotplug
xtensa: add SMP support
xtensa: add MX irqchip
xtensa: clear timer IRQ unconditionally in its handler
xtensa: clean up do_interrupt/do_IRQ
...
Not removing pm qos request and free memory for it can cause crash,
when some other driver use pm qos. For example, this oops:
BUG: unable to handle kernel paging request at fffffffffffffff8
IP: [<ffffffff81307a6b>] plist_add+0x5b/0xd0
Call Trace:
[<ffffffff810acf25>] pm_qos_update_target+0x125/0x1e0
[<ffffffff810ad071>] pm_qos_add_request+0x91/0x100
[<ffffffffa053ec14>] e1000_open+0xe4/0x5b0 [e1000e]
was caused by earlier i915 probe failure:
[drm:i915_report_and_clear_eir] *ERROR* EIR stuck: 0x00000010, masking
[drm:init_ring_common] *ERROR* render ring initialization failed ctl 0001f001 head 00003004 tail 00000000 start 00003000
[drm:i915_driver_load] *ERROR* failed to init modeset
i915: probe of 0000:00:02.0 failed with error -5
Bug report:
http://bugzilla.redhat.com/show_bug.cgi?id=1057533
Reported-by: Giandomenico De Tullio <ghisha@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[danvet: Drop unnecessary code movement.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SPC-4 states that data-integrity errors shall also report
the failed sector in CHECK_CONDITION response sense data
information field.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch propigates the use of task state bitmask now used by
percpu_ida_alloc() up the iscsi-target callchain, replacing the
use of GFP_ATOMIC for TASK_RUNNING, and GFP_KERNEL for
TASK_INTERRUPTIBLE.
Also, drop the unnecessary gfp_t parameter to isert_allocate_cmd(),
and just pass TASK_INTERRUPTIBLE into iscsit_allocate_cmd().
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug where connection reset would hang
indefinately once percpu_ida_alloc() was starved for tags, due
to the fact that it always assumed uninterruptible sleep mode.
So now make percpu_ida_alloc() check for signal_pending_state() for
making interruptible sleep optional, and convert iscsit_allocate_cmd()
to set TASK_INTERRUPTIBLE for GFP_KERNEL, or TASK_RUNNING for
GFP_ATOMIC.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Kent Overstreet <kmo@daterainc.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- Remove unnecessary and dangerous use of device_lock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t9+R
-----END PGP SIGNATURE-----
Merge tag 'vfio-v3.14-rc1' of git://github.com/awilliam/linux-vfio
Pull vfio update from Alex Williamson:
- convert to misc driver to support module auto loading
- remove unnecessary and dangerous use of device_lock
* tag 'vfio-v3.14-rc1' of git://github.com/awilliam/linux-vfio:
vfio-pci: Don't use device_lock around AER interrupt setup
vfio: Convert control interface to misc driver
misc: Reserve minor for VFIO
All bug fixes, two tagged for -stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=d81E
-----END PGP SIGNATURE-----
Merge tag 'md/3.14' of git://neil.brown.name/md
Pull md updates from Neil Brown:
"All bug fixes, two tagged for -stable"
* tag 'md/3.14' of git://neil.brown.name/md:
md/raid5: close recently introduced race in stripe_head management.
md/raid5: fix long-standing problem with bitmap handling on write failure.
md: check command validity early in md_ioctl().
md: ensure metadata is writen after raid level change.
md/raid10: avoid fullsync when not necessary.
md: allow a partially recovered device to be hot-added to an array.
md: Change handling of save_raid_disk and metadata update during recovery.
- Add new documents with guidelines for DT binding stability and review
process. This is one of the outcomes of Kernel Summit DT discussions.
- Remove a bunch of device_type usage which is only for OF and
deprecated with FDT.
- Fix a long standing issue with compatible string match ordering.
- Various minor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJS4T/IAAoJEMhvYp4jgsXiGY4H/jw3ldOrsRK+E2WuTi2iFsaj
UrDBEkLeL920abdk1Ba19AtMLBoroUr1HuyrCqiKfhilzqWi662YWCLWHZ6KPzGG
6d5+YztZ2MnoPzcD7RHd9aojL79V8/OGJpitm9NEDdq5GlQ2/v8/Q7ap2tSGFAV6
+qp5AKLUE0vNm8Lx+0t7NE1Qov2QFvbNycSk4CPOG7nvNBBOfbj7yuofFJmcQxZZ
gjOYEve9lf+jjigwq5YyQdYdAPs2kAKE8/DtJf6WaRXjyWpLpvgYqgPJ9mWcJzFK
FKOHvgfxyK0VmWuIfVKg5GASomWPzABXaBGJWG1phtLa3H+Qv+ZKgtYduKrlxkw=
=vXAO
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Add new documents with guidelines for DT binding stability and review
process. This is one of the outcomes of Kernel Summit DT discussions
- Remove a bunch of device_type usage which is only for OF and
deprecated with FDT
- Fix a long standing issue with compatible string match ordering
- Various minor binding documentation updates
* tag 'devicetree-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: add rockchip vendor prefix
serial: vt8500: Add missing binding document for arch-vt8500 serial driver.
dt/bindings: submitting patches and ABI documents
DT: Add vendor prefix for Emerging Display Technologies
of: add vendor prefixe for EPFL
of: add vendor prefix for Gumstix
of: add vendor prefix for Ka-Ro electronics GmbH
devicetree: macb: Document clock properties
dts: bindings: trivial clock bindings doc fixes
of: Fix __of_device_is_available check
dt/bindings: Remove device_type "serial" from marvell,mv64360-mpsc
dt/bindings: remove device_type "network" references
dt/bindings: remove users of device_type "mdio"
dt/bindings: Remove references to linux,phandle properties
dt/bindings: Remove all references to device_type "ethernet-phy"
of: irq: Ignore disabled intc's when searching map
of: irq: Ignore disabled interrupt controllers
OF: base: match each node compatible against all given matches first
dt-bindings: add GIC-400 binding
- Flow steering for InfiniBand UD traffic
- IP-based addressing for IBoE aka RoCE
- Pass SRP submaintainership from Dave to Bart
- SRP transport fixes from Bart
- Add the new Cisco usNIC low-level device driver
- Various other fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=wAWA
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.14:
- Flow steering for InfiniBand UD traffic
- IP-based addressing for IBoE aka RoCE
- Pass SRP submaintainership from Dave to Bart
- SRP transport fixes from Bart
- Add the new Cisco usNIC low-level device driver
- Various other fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (75 commits)
IB/mlx5: Verify reserved fields are cleared
IB/mlx5: Remove old field for create mkey mailbox
IB/mlx5: Abort driver cleanup if teardown hca fails
IB/mlx5: Allow creation of QPs with zero-length work queues
mlx5_core: Fix PowerPC support
mlx5_core: Improve debugfs readability
IB/mlx5: Add support for resize CQ
IB/mlx5: Implement modify CQ
IB/mlx5: Make sure doorbell record is visible before doorbell
mlx5_core: Use mlx5 core style warning
IB/mlx5: Clear out struct before create QP command
mlx5_core: Fix out arg size in access_register command
RDMA/nes: Slight optimization of Ethernet address compare
IB/qib: Fix QP check when looping back to/from QP1
RDMA/cxgb4: Fix gcc warning on 32-bit arch
IB/usnic: Remove unused includes of <linux/version.h>
RDMA/amso1100: Add check if cache memory was allocated before freeing it
IPoIB: Report operstate consistently when brought up without a link
IB/core: Fix unused variable warning
RDMA/cma: Handle global/non-linklocal IPv6 addresses in cma_check_linklocal()
...
Pull input subsystem updates from Dmitry Torokhov:
"Just a swath of driver fixes and cleanups, no new drivers this time
(although ALPS now supports one of the newer protocols, more to come)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: wacom - add support for DTU-1031
Input: wacom - fix wacom->shared guards for dual input devices
Input: edt_ft5x06 - use devm_* functions where appropriate
Input: hyperv-keyboard - pass through 0xE1 prefix
Input: logips2pp - fix spelling s/reciver/receiver/
Input: delete non-required instances of include <linux/init.h>
Input: twl4030-keypad - convert to using managed resources
Input: twl6040-vibra - remove unneeded check for CONFIG_OF
Input: twl4030-keypad - add device tree support
Input: twl6040-vibra - add missing of_node_put
Input: twl4030-vibra - add missing of_node_put
Input: i8042 - cleanup SERIO_I8042 dependencies
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on x86
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on unicore32
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on sparc
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO for SH_CAYMAN
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on powerpc
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on mips
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on IA64
Input: i8042 - select ARCH_MIGHT_HAVE_PC_SERIO on ARM/Footbridge
...
This is a rather boring pull request. There is one new fb driver, OpenCores
VGA/LCD, but other than that it's just minor cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=RmAl
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
"This is a rather boring pull request. There is one new fb driver,
OpenCores VGA/LCD, but other than that it's just minor cleanups and
fixes"
* tag 'fbdev-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (51 commits)
i810: delete useless variable
video: add OpenCores VGA/LCD framebuffer driver
video/logo: Remove MIPS-specific include section
tgafb: potential NULL dereference in init
video: mmp: Using plain integer as NULL pointer
video: mmp: delete a stray mutex_unlock()
video: amba-clcd: Make CLCD driver available on more platforms
video: Replace local macro with PCI standard macro
fbmem: really support wildcard video=options for all fbdev drivers
video: vgacon: Don't build on arm64
video: mx3fb: Allow blocking during framebuffer allocation
fbcon: Fix memory leak in fbcon_exit().
fbcon: trivial optimization for fbcon_exit
video: pxa168fb: Cleanup pxa168fb.h file
video: pxa: Cleanup video-pxafb.h header
video: msm: Cleanup video-msm_fb.h header
video: ep93xx: Cleanup video-ep93xx.h header
video: mxsfb: fix broken videomode selection
video: mxsfb: convert pr_debug()/dev_dbg() to pr_err()/dev_err() for error messages
video: vmlfb: remove unnecessary pci_set_drvdata()
...
Pull thermal management updates from Zhang Rui:
"This time, the biggest change is the work of representing hardware
thermal properties in device tree infrastructure.
This work includes the introduction of a device tree bindings for
describing the hardware thermal behavior and limits, and also a parser
to read and interpret the data, and build thermal zones and thermal
binding parameters. It also contains three examples on how to use the
new representation on sensor devices, using three different drivers to
accomplish it. One driver is in thermal subsystem, the TI SoC
thermal, and the other two drivers are in hwmon subsystem.
Actually, this would be the first step of the complete work because we
still need to check other potential drivers to be converted and then
validate the proposed API. But the reason why I include it in this
pull request is that, first, this change does not hurt any others
without using this approach, second, the principle and concept of this
change would not break after converting the remaining drivers. BTW,
as you can see, there are several points in this change that do not
belong to thermal subsystem. Because it has been suggested by Guenter
R that in such cases, it is recommended to send the complete series
via one single subsystem.
Specifics:
- representing hardware thermal properties in device tree
infrastructure
- fix a regression that the imx thermal driver breaks system suspend.
- introduce ACPI INT3403 thermal driver to retrieve temperature data
from the INT3403 ACPI device object present on some systems.
- introduce debug statement for thermal core and step_wise governor.
- assorted fixes and cleanups for thermal core, cpu cooling, exynos
thrmal, intel powerclamp and imx thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: remove const flag from .ops of imx thermal
Thermal: update thermal zone device after setting emul_temp
intel_powerclamp: Fix cstate counter detection.
thermal: imx: add necessary clk operation
Thermal cpu cooling: return error if no valid cpu frequency entry
thermal: fix cpu_cooling max_level behavior
thermal: rcar-thermal: Enable driver compilation with COMPILE_TEST
thermal: debug: add debug statement for core and step_wise
thermal: imx_thermal: add module device table
drivers: thermal: Mark function as static in x86_pkg_temp_thermal.c
thermal:samsung: fix compilation warning
thermal: imx: correct suspend/resume flow
thermal: exynos: fix error return code
Thermal: ACPI INT3403 thermal driver
MAINTAINERS: add thermal bindings entry in thermal domain
arm: dts: make OMAP4460 bandgap node to belong to OCP
arm: dts: make OMAP443x bandgap node to belong to OCP
arm: dts: add cooling properties on omap5 cpu node
arm: dts: add omap5 thermal data
arm: dts: add omap5 CORE thermal data
...
The adapter is freed before we check its flags. It was caused
by commit 144be3d ("net/cxgb4: Avoid disabling PCI device for
towice"). The problem was reported by Intel's "0-day" tool.
The patch fixes it to avoid reverting commit 144be3d.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
With this patch we prevent the irq from being fired when it is
registered. The Hardware fires an IRQ when input signal XOR polarity
AND gpio mask is 1. Now we are setting polarity to a vlaue so that is
is 0 when we register it.
In addition we also set the irq mask register to 0 when the irq handler
is initialized, so all gpio irqs are masked and there will be no
unexpected irq.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6304/
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no driver
is bound) modified the driver core to always clear .driver and .drvdata
on remove or probe error. No need for the I2C core to do it.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This file is controlled by a tristate Kconfig option, and hence
needs to include module.h so that it can get module_init() once
we relocate it from init.h into module.h in the future.
Note that module_exit() appears to be missing from the driver, so
it is questionable whether it would actually work for a removal
and reload cycle if it was configured for a modular build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use exactly the same log messages in the legacy setup function and the
SB800+ setup function. This way strings can be reused, which saves
some bytes in the generated binary.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Same messages for AMD main and auxiliary SMBus controllers lead to confusion,
this patch is to remove confusion and keep consistent with non-AMD products.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The locations of SMBus register base address and enablement bit are changed
from AMD ML, which need this patch to be supported.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@vger.kernel.org
This reverts commit 446f254566.
I've left the masking in the pageflip code since that seems to be some
useful piece of preemptive robustness.
Iirc I've merged this patch under the assumption that the BIOS leaves
some random gunk in the lower bits and gets unhappy if we trample on
them. We have quite a few case like this, so this made sense.
Now I've just learned that there's actual hardware features bits in
the low 12 bits, and the kernel needs to preserve them to allow a
userspace blob to do its job. Given Dave Airlie's clear stance on
userspace blob drivers I've quickly chatted with him and he doesn't
seem too happy. So let's revert this.
If there are indeed bits that we must preserve in this range then we
can ressurrect this patch, but with proper documentation for those
bits supplied. And we probably also need to think a bit about
interactions with our driver.
Cc: Armin Reese <armin.c.reese@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Airlie <airlied@linux.ie>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To provide access to the set-partition-resource-parameter interface
to user space add a new attribute to hypfs/debugfs:
* s390_hypsfs/diag_304
The data for the query-partition-resource-parameters command can
be access by a read on the attribute. All other diagnose 0x304
requests need to be submitted via ioctl with CAP_SYS_ADMIN rights.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge second patch-bomb from Andrew Morton:
- various misc bits
- the rest of MM
- add generic fixmap.h, use it
- backlight updates
- dynamic_debug updates
- printk() updates
- checkpatch updates
- binfmt_elf
- ramfs
- init/
- autofs4
- drivers/rtc
- nilfs
- hfsplus
- Documentation/
- coredump
- procfs
- fork
- exec
- kexec
- kdump
- partitions
- rapidio
- rbtree
- userns
- memstick
- w1
- decompressors
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (197 commits)
lib/decompress_unlz4.c: always set an error return code on failures
romfs: fix returm err while getting inode in fill_super
drivers/w1/masters/w1-gpio.c: add strong pullup emulation
drivers/memstick/host/rtsx_pci_ms.c: fix ms card data transfer bug
userns: relax the posix_acl_valid() checks
arch/sh/kernel/dwarf.c: use rbtree postorder iteration helper instead of solution using repeated rb_erase()
fs-ext3-use-rbtree-postorder-iteration-helper-instead-of-opencoding-fix
fs/ext3: use rbtree postorder iteration helper instead of opencoding
fs/jffs2: use rbtree postorder iteration helper instead of opencoding
fs/ext4: use rbtree postorder iteration helper instead of opencoding
fs/ubifs: use rbtree postorder iteration helper instead of opencoding
net/netfilter/ipset/ip_set_hash_netiface.c: use rbtree postorder iteration instead of opencoding
rbtree/test: test rbtree_postorder_for_each_entry_safe()
rbtree/test: move rb_node to the middle of the test struct
rapidio: add modular rapidio core build into powerpc and mips branches
partitions/efi: complete documentation of gpt kernel param purpose
kdump: add /sys/kernel/vmcoreinfo ABI documentation
kdump: fix exported size of vmcoreinfo note
kexec: add sysctl to disable kexec_load
fs/exec.c: call arch_pick_mmap_layout() only once
...
entirely of new platform/driver support. There are some conversions of
existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc tree
this pull request is broken into two pieces. The second piece will be
sent out after arm-soc sends you the pull request that merged in core
support for the HiSilicon 3620 platform. That same pull request from
arm-soc depends on this pull request to merge in those HiSilicon bits
without causing build failures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=Hh66
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework changes from Mike Turquette:
"The first half of the clk framework pull request is made up almost
entirely of new platform/driver support. There are some conversions
of existing drivers to the common-clock Device Tree binding, and a few
non-critical fixes to the framework.
Due to an entirely unnecessary cyclical dependency with the arm-soc
tree this pull request is broken into two pieces. The second piece
will be sent out after arm-soc sends you the pull request that merged
in core support for the HiSilicon 3620 platform. That same pull
request from arm-soc depends on this pull request to merge in those
HiSilicon bits without causing build failures"
[ Just did the ARM SoC merges, so getting ready for the second clk tree
pull request - Linus ]
* tag 'clk-for-linus-3.14-part1' of git://git.linaro.org/people/mike.turquette/linux: (97 commits)
devicetree: bindings: Document qcom,mmcc
devicetree: bindings: Document qcom,gcc
clk: qcom: Add support for MSM8660's global clock controller (GCC)
clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8974's global clock controller (GCC)
clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)
clk: qcom: Add support for MSM8960's global clock controller (GCC)
clk: qcom: Add reset controller support
clk: qcom: Add support for branches/gate clocks
clk: qcom: Add support for root clock generators (RCGs)
clk: qcom: Add support for phase locked loops (PLLs)
clk: qcom: Add a regmap type clock struct
clk: Add set_rate_and_parent() op
reset: Silence warning in reset-controller.h
clk: sirf: re-arch to make the codes support both prima2 and atlas6
clk: composite: pass mux_hw into determine_rate
clk: shmobile: Fix MSTP clock array initialization
clk: shmobile: Fix MSTP clock index
ARM: dts: Add clock provider specific properties to max77686 node
clk: max77686: Register OF clock provider
...
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files that
don't require corresponding C changes any more, which is indicating that
the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over to fully
support the platform with DT.
* Renesas platforms continue their conversion over from legacy platform devices
to DT-based for hardware description.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4o2d
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with some
random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m, i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pgLW
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with
some random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m,
i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in
industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (201 commits)
ARM: tegra: fix tegra_powergate_sequence_power_up() inline
ARM: msm_defconfig: Update for multi-platform
ARM: msm: Move MSM's DT based hardware to multi-platform support
ARM: msm: Only build timer.c if required
ARM: msm: Only build clock.c on proc_comm based platforms
ARM: ux500: Enable system suspend with WFI support
ARM: ux500: turn on PRINTK_TIME in u8500_defconfig
ARM: shmobile: r8a7790: Fix I2C controller names
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they came in
quite late and we decided to keep them deferred until the first -stable
release to get more coverage instead of squeezing them into 3.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=QhN9
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"As usual, we have a batch of fixes that weren't considered significant
enough to warrant going into the later -rcs for previous release, so
they are queued up on this branch.
A handful of these are for various DT fixups for Samsung platforms,
and a handful of other minor things.
There are also a couple of stable-marked patches for mvebu -- they
came in quite late and we decided to keep them deferred until the
first -stable release to get more coverage instead of squeezing them
into 3.13"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
ARM: at91: smc: bug fix in sam9_smc_cs_read()
i2c: mv64xxx: Document the newly introduced Armada XP A0 compatible
i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
ARM: mvebu: Add support to get the ID and the revision of a SoC
ARM: dts: msm: Fix gpio interrupt and reg length
irqchip: sirf: set IRQ_LEVEL status_flags
ARM: OMAP2+: gpmc: Move legacy GPMC width setting
ARM: OMAP2+: gpmc: Introduce gpmc_set_legacy()
ARM: OMAP2+: gpmc: Move initialization outside the gpmc_t condition
ARM: OMAP2+: board-generic: update SoC compatibility strings
Documentation: dt: OMAP: explicitly state SoC compatible strings
ARM: OMAP2+: enable AM33xx SOC EVM audio
ARM: OMAP2+: Select USB PHY for AM335x SoC
ARM: bcm2835: Fix grammar in help message
ARM: msm: trout: fix uninit var warning
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
...
Pull ARM updates from Russell King:
"In this set, we have:
- Refactoring of some of the old StrongARM-1100 GPIO code to make
things simpler by Dmitry Eremin-Solenikov
- Read-only and non-executable support for modules on ARM from Laura
Abbot
- Removal of unnecessary set_drvdata() calls in AMBA code
- Some non-executable support for kernel lowmem mappings at the 1MB
section granularity, and dumping of kernel page tables via debugfs
- Some improvements for the timer/clock code on Footbridge platforms,
and cleanup some of the LED code there
- Fix fls/ffs() signatures to match x86 to prevent build warnings,
particularly where these are used with min/max() macros
- Avoid using the bootmem allocator on ARM (patches from Santosh
Shilimkar)
- Various asid/unaligned access updates from Will Deacon"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (51 commits)
ARM: SMP implementations are not supposed to return from smp_ops.cpu_die()
ARM: ignore memory below PHYS_OFFSET
Fix select-induced Kconfig warning for ZBOOT_ROM
ARM: fix ffs/fls implementations to match x86
ARM: 7935/1: sa1100: collie: add gpio-keys configuration
ARM: 7932/1: bcm: Add DEBUG_LL console support
ARM: 7929/1: Remove duplicate SCHED_HRTICK config option
ARM: 7928/1: kconfig: select HAVE_EFFICIENT_UNALIGNED_ACCESS for CPUv6+ && MMU
ARM: 7927/1: dcache: select DCACHE_WORD_ACCESS for big-endian CPUs
ARM: 7926/1: mm: flesh out and fix the comments in the ASID allocator
ARM: 7925/1: mm: keep track of last ASID allocation to improve bitmap searching
ARM: 7924/1: mm: don't bother with reserved ttbr0 when running with LPAE
ARM: PCI: add legacy IDE IRQ implementation
ARM: footbridge: cleanup LEDs code
ARM: pgd allocation: retry on failure
ARM: footbridge: add one-shot mode for DC21285 timer
ARM: footbridge: add sched_clock implementation
ARM: 7922/1: l2x0: add Marvell Tauros3 support
ARM: 7877/1: use built-in byte swap function
ARM: 7921/1: mcpm: remove redundant dsb instructions prior to sev
...
Pull audit update from Eric Paris:
"Again we stayed pretty well contained inside the audit system.
Venturing out was fixing a couple of function prototypes which were
inconsistent (didn't hurt anything, but we used the same value as an
int, uint, u32, and I think even a long in a couple of places).
We also made a couple of minor changes to when a couple of LSMs called
the audit system. We hoped to add aarch64 audit support this go
round, but it wasn't ready.
I'm disappearing on vacation on Thursday. I should have internet
access, but it'll be spotty. If anything goes wrong please be sure to
cc rgb@redhat.com. He'll make fixing things his top priority"
* git://git.infradead.org/users/eparis/audit: (50 commits)
audit: whitespace fix in kernel-parameters.txt
audit: fix location of __net_initdata for audit_net_ops
audit: remove pr_info for every network namespace
audit: Modify a set of system calls in audit class definitions
audit: Convert int limit uses to u32
audit: Use more current logging style
audit: Use hex_byte_pack_upper
audit: correct a type mismatch in audit_syscall_exit()
audit: reorder AUDIT_TTY_SET arguments
audit: rework AUDIT_TTY_SET to only grab spin_lock once
audit: remove needless switch in AUDIT_SET
audit: use define's for audit version
audit: documentation of audit= kernel parameter
audit: wait_for_auditd rework for readability
audit: update MAINTAINERS
audit: log task info on feature change
audit: fix incorrect set of audit_sock
audit: print error message when fail to create audit socket
audit: fix dangling keywords in audit_log_set_loginuid() output
audit: log on errors from filter user rules
...
This patch is used to add support for ms card. The main difference
between ms card and mspro card is long data transfer mode. mspro card
can use auto mode DMA for long data transfer, but ms can not use this
mode, it should use normal mode DMA.
The memstick core added support for ms card, but the original driver will
make ms card fail at initialization, because it uses auto mode DMA. This
patch makes the ms card work properly.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for SMBus-only adapters (e.g. i2c-piix4). The driver has
implemented only support for I2C adapters which implement the
I2C_FUNC_SMBUS_I2C_BLOCK functionality before.
With this patch it is possible to load and use the RTC driver with I2C and
SMBUS adapters like the rtc-ds1307 does.
Tested on AMD G Series Platform (i2c-piix4 adapter driver).
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If CONFIG_PM_SLEEP=n:
drivers/rtc/rtc-s5m.c:643: warning: `s5m_rtc_resume' defined but not used
drivers/rtc/rtc-s5m.c:654: warning: `s5m_rtc_suspend' defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current MAX8907 driver has two issues related to weekday value
handling:
1)
The HW WEEKDAY register has range 0..6 rather than 1..7 as documented.
Note that I validated the actual HW range by observing the HW register
roll from 6->0 rather than 6->7->1 as would otherwise be expected.
This matches Linux's tm_wday range of 0..6.
When the CMOS RAM content is lost, the date returned from the device is
2007-01-01 00:00:00, which is a Monday. The WEEKDAY register reads 1 in
this case. This matches the numbering in Linux's tm_wday field.
Hence we should write Linux's tm_wday value to the register without
modifying it. Hence, remove the +1/-1 calculations for WEEKDAY/tm_wday.
2)
There's no need to make alarms match on the WEEKDAY register, since the
other fields together uniquely define the alarm date/time. Ignoring the
WEEKDAY value in the match isolates the driver from any incorrect value in
the current time copy of the WEEKDAY register.
Each change individually, or both together, solves an issue that I
observed; "hwclock -r" would time out waiting for its alarm to fire if the
CMOS RAM content had been lost, and hence the WEEKDAY register value
mismatched what the driver expected it to be. "hwclock -w" would solve
this by over-writing the HW default WEEKDAY register value with what the
driver expected.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'hym8563_clkout_ops' is used only in this file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'hym8563_dt_idtable' is always compiled in. Hence the helper macro is not
needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'ds1742_rtc_of_match' is always compiled in. Hence the helper macro is
not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If hpet_register_irq_handler() fails, cmos_do_probe() will incorrectly
return 0.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Assign RTC device IDs based on device tree /aliases entries if present,
falling back to the existing numbering scheme if there is no /aliases
entry (which includes when the system isn't booted using DT), or there is
a numbering conflict.
This is useful in systems with multiple RTC devices, to ensure that the
best RTC device is selected as /dev/rtc0, which provides the overall
system time.
For example, Tegra has an on-SoC RTC that is not battery backed, typically
coupled with an off-SoC RTC that is battery backed. Only the latter is
useful for populating the system time, yet the former is useful e.g. for
wakeup timing, since the time is not lost when the system is sleeps.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a coccinelle error regarding usage of IS_ERR and PTR_ERR instead of
PTR_ERR_OR_ZERO.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On ARAnyM (emulating an Atari Falcon, which doesn't have an RTC IRQ, as
the Second Multi Function Peripheral MFP 68901 is available on Atari TT
only), rtc-cmos doesn't work well:
- The date is of by 32 years (2045 instead of 2013):
rtc_cmos rtc_cmos: setting system clock to 2045-12-02 10:56:17 UTC
(2395824977)
- The hwclock utility doesn't work:
hwclock: ioctl() to /dev/rtc to turn on update interrupts failed
unexpectedly, errno=5: Input/output error.
As rtc-generic works fine for the RTC part, and nvram works for the NVRAM
part, we'll continue on using that.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Haoyu Microelectronics HYM8563 provides rtc and alarm functions as
well as a clock output of up to 32kHz.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Richard Weinberger <richard.weinberger@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch allows the driver to be enabled with devicetree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
clk_prepare_enable() may fail, so let's check its return value and
propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no need to jump to the 'exit_free_pdata' label when
devm_clk_get() fails, as we can directly return the error and simplify the
code a bit.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver core clears the driver data to NULL after device_release or on
probe failure. Thus, it is not needed to manually clear the device driver
data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_* calls for rtc and irq registration and get rid of
remove callback for platform driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes a couple of changes to the SMBIOS/DMI scanning
code so it can be used on other archs (such as ARM and arm64):
(a) wrap the calls to ioremap()/iounmap(), this allows the use of a
flavor of ioremap() more suitable for random unaligned access;
(b) allow the non-EFI fallback probe into hardcoded physical address
0xF0000 to be disabled.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unnecessary parentheses in order to fix the following checkpatch
error.
ERROR: return is not a function, parentheses are not required
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unnecessary parentheses in order to fix the following checkpatch
error.
ERROR: return is not a function, parentheses are not required
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The __initdata marker can be virtually anywhere on the line, EXCEPT right
after "struct". The preferred location is before the "=" sign if there is
one, or before the trailing ";" otherwise. It also fixes the following
chechpatch warning.
WARNING: __initdata should be placed after kb3886bl_device_table[]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_lcd_device_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_backlight_device_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We fixed the call to request_mem_region() in commit 3354f73b24
("drivers/vlynq/vlynq.c: fix resource size off by 1 error"). But we
need to fix the call the release_mem_region() as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following warning in the aty128fb driver:
drivers/video/aty/aty128fb.c:363:12: warning: 'backlight' defined but not used [-Wunused-variable]
static int backlight = 0;
^
as the variable's value is only read if CONFIG_FB_ATY128_BACKLIGHT=y. The
variable is also set if MODULE is unset[*].
[*] I wonder if the conditional wrapper around aty128fb_setup() should be
using CONFIG_MODULE rather than MODULE.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the following pointer-integer size mismatch warning in
tps65217_probe():
drivers/mfd/tps65217.c: In function 'tps65217_probe':
drivers/mfd/tps65217.c:173:13: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
chip_id = (unsigned int)match->data;
^
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the following pointer-integer size mismatch warning in
max8998_i2c_get_driver_data():
drivers/mfd/max8998.c: In function 'max8998_i2c_get_driver_data':
drivers/mfd/max8998.c:178:10: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
return (int)match->data;
^
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Mark Brown <broonie@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following warning:
drivers/gpu/drm/gma500/backlight.c:29:13: warning: 'do_gma_backlight_set' defined but not used [-Wunused-function]
by moving the entire function inside the conditional section currently
inside of it. All the places that call it are so conditionalised.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RAM block device support module name changed to brd.ko some years ago
with an "rd" alias to match previous module implementation. This patch
updates its Kconfig definition.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a bug in omap2_mbox_probe() where we try do:
mbox->irq = platform_get_irq(pdev, info->irq_id);
if (mbox->irq < 0) {
The problem is that mbox->irq is unsigned so the error handling doesn't
work. I've changed it to a signed integer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Suman Anna <s-anna@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Omar Ramirez Luna <omar.ramirez@copitl.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
o Refactored MSI-x vector calculation for All adapters.
Decoupled logic in the code which was using same call to
request MSI-x vectors in default driver load, as well as
during set_channel() operation for TSS/RSS. This refactoring
simplifies code for TSS/RSS code path as well as probe path
of the driver load for all adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactor configuration of interrupt coalescing parameters for
all supported adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MSI/MSI-X mode in poll controller routine.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Added hardware ops for interrupt enable/disable functions
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Dump each Tx queue details with all descriptors, queue indices
and Tx queue stats to imporve data colletion in situations
where Tx timeout occurs.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use boolean type instead of u8.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the option conversion downdelay and updelay divide a u64
and on a 32 bit this causes the following errors:
ERROR: "__udivdi3" [drivers/net/bonding/bonding.ko] undefined!
ERROR: "__umoddi3" [drivers/net/bonding/bonding.ko] undefined!
Fix it by using a normal int instead because newval->value is capped
at INT_MAX by the way the option is defined.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of a workaround for a hardware erratum in the SFC9100 family
(SF bug 35388), the TX_DESC_UPD_DWORD register address is also used
for communicating with the event block, and only descriptor pointer
values < 2048 are valid.
If the TX DMA ring size is increased to 4096 descriptors (which the
firmware still allows) then we may write a descriptor pointer
value >= 2048, which has entirely different and undesirable effects!
Limit the TX DMA ring size correctly when this workaround is in
effect.
Fixes: 8127d661e7 ('sfc: Add support for Solarflare SFC9100 family')
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the practice set by commit 0afb166 "vxlan: Add capability
of Rx checksum offload for inner packet" is applied when the skb
goes through the portion of the RX code which is shared between
vxlan netdevices and ovs vxlan port instances.
Cc: Joseph Gasparakis <joseph.gasparakis@intel.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this situation then ARRAY_SIZE() and sizeof() are the same, but we're
really dealing with array indexes and not byte offsets so ARRAY_SIZE()
is cleaner.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We possibly retrieve the adapter's statistics during EEH recovery
and that should be disallowed. Otherwise, it would possibly incur
replicate EEH error and EEH recovery is going to fail eventually.
The patch reuses statistics lock and checks net_device is attached
before going to retrieve statistics, so that the problem can be
avoided.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have EEH error happens to the adapter and we have to remove
it from the system for some reasons (e.g. more than 5 EEH errors
detected from the device in last hour), the adapter will be disabled
for towice separately by eeh_err_detected() and remove_one(), which
will incur following unexpected backtrace. The patch tries to avoid
it.
WARNING: at drivers/pci/pci.c:1431
CPU: 12 PID: 121 Comm: eehd Not tainted 3.13.0-rc7+ #1
task: c0000001823a3780 ti: c00000018240c000 task.ti: c00000018240c000
NIP: c0000000003c1e40 LR: c0000000003c1e3c CTR: 0000000001764c5c
REGS: c00000018240f470 TRAP: 0700 Not tainted (3.13.0-rc7+)
MSR: 8000000000029032 <SF,EE,ME,IR,DR,RI> CR: 28000024 XER: 00000004
CFAR: c000000000706528 SOFTE: 1
GPR00: c0000000003c1e3c c00000018240f6f0 c0000000010fe1f8 0000000000000035
GPR04: 0000000000000000 0000000000000000 00000000003ae509 0000000000000000
GPR08: 000000000000346f 0000000000000000 0000000000000000 0000000000003fef
GPR12: 0000000028000022 c00000000ec93000 c0000000000c11b0 c000000184ac3e40
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR24: 0000000000000000 c0000000009398d8 c00000000101f9c0 c0000001860ae000
GPR28: c000000182ba0000 00000000000001f0 c0000001860ae6f8 c0000001860ae000
NIP [c0000000003c1e40] .pci_disable_device+0xd0/0xf0
LR [c0000000003c1e3c] .pci_disable_device+0xcc/0xf0
Call Trace:
[c0000000003c1e3c] .pci_disable_device+0xcc/0xf0 (unreliable)
[d0000000073881c4] .remove_one+0x174/0x320 [cxgb4]
[c0000000003c57e0] .pci_device_remove+0x60/0x100
[c00000000046396c] .__device_release_driver+0x9c/0x120
[c000000000463a20] .device_release_driver+0x30/0x60
[c0000000003bcdb4] .pci_stop_bus_device+0x94/0xd0
[c0000000003bcf48] .pci_stop_and_remove_bus_device+0x18/0x30
[c00000000003f548] .pcibios_remove_pci_devices+0xa8/0x140
[c000000000035c00] .eeh_handle_normal_event+0xa0/0x3c0
[c000000000035f50] .eeh_handle_event+0x30/0x2b0
[c0000000000362c4] .eeh_event_handler+0xf4/0x1b0
[c0000000000c12b8] .kthread+0x108/0x130
[c00000000000a168] .ret_from_kernel_thread+0x5c/0x74
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes percpu_ida_alloc() + callers to accept task state
bitmask for prepare_to_wait() for code like target/iscsi that needs
it for interruptible sleep, that is provided in a subsequent patch.
It now expects TASK_UNINTERRUPTIBLE when the caller is able to sleep
waiting for a new tag, or TASK_RUNNING when the caller cannot sleep,
and is forced to return a negative value when no tags are available.
v2 changes:
- Include blk-mq + tcm_fc + vhost/scsi + target/iscsi changes
- Drop signal_pending_state() call
v3 changes:
- Only call prepare_to_wait() + finish_wait() when != TASK_RUNNING
(PeterZ)
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The threshold values for RX interrupt mitigation
are different for AR9003 and AR9002 families.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Process GTT interrupts" accidentally
had a line that was commented out.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the right function to update frequency value.
If rx skb is probe response or beacon, the wrong frequency value can
cause problem that bss info can't be updated when it should be.
Cc: <stable@vger.kernel.org>
Fixes: 8318d78a44 ("cfg80211 API for channels/bitrates, mac80211
and driver conversion")
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
8 bytes preamble
14 bytes src/dst/eth_type
6 bytes 0xff:0xff..
http://en.wikipedia.org/wiki/Wake-on-LAN#Magic_packethttp://en.wikipedia.org/wiki/EtherType
This will fail if we VLAN or the magic packet is encapsulated
as a UDP packet...
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
List what needs to be done to this driver to get it merged to the
"proper" part of the kernel tree.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up a bunch of build warnings by removing functions and variables that
aren't being used.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These function parameters are incorrect for the callbacks. Luckily the
functions don't actually do anything, so the code still "works" just
fine...
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This comes directly from the Realtek tarball, filename:
wifi_driver_8821ae_0018.1129.2013.tar.gz
I mushed the three modules (btcoexist, rtlwifi and rtl8821ae) together
into one, in order to make it all build as one stand-alone module.
After the btcoexist driver gets merged upstream, I'll pull it out of
here, and will continue to work on removing this version of rtlwifi in
order to use the in-kernel one.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible for chip->fixes to be null. Check before dereferencing it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable <stable@vger.kernel.org> # 3.11+
Signed-off-by: Chris Ball <chris@printf.net>
The head number of a given display controller is fixed in hardware and
required to program outputs appropriately. Relying on the driver probe
order to determine this number will not work, since that could yield a
situation where the second head was probed first and would be assigned
head number 0 instead of 1.
By explicitly specifying the head number in the device tree, it is no
longer necessary to rely on these assumptions. As a fallback, if the
property isn't available, derive the head number from the display
controller node's position in the device tree. That's somewhat more
reliable than the previous default but not a proper solution.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Input GPIO changes can generate interrupts, but we need kind of ACK for
them by changing IRQ polarity. This is required to stop hardware from
keep generating interrupts and generate another one on the next GPIO
state change.
This code allows using GPIOs with standard interrupts and add for
example GPIO buttons support.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6216/
Now that the UART block defines have been moved to a separate file,
include that one and do not longer rely on the MIPS-specific
bcm63xx_regs.h header file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6204/
bcm_{readl,writel} macros expand to __raw_{readl,writel}, use these
directly such that we do not rely on the platform to provide these for
us. As a result, we no longer use bcm63xx_io.h, so remove that inclusion
too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6201/
bcm63xx_irqs.h is included but we are not using anything from it, drop
that include.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6205/
'lay' is not very meaningful, so use it 'layer' instead to let the dev_info()
clearer.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add new definitions for hotplug live status bits for VLV2 since they're
in reverse order from the gen4x ones.
Changelog:
- Restored gen4 bit definitions
- Added new definitions for VLV2
- Added platform check for IS_VALLEYVIEW() in dp_detect to use the correct
bit defintions
- Replaced a lost trailing brace for the added switch()
Signed-off-by: Todd Previte <tprevite@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73951
[danvet: Switch to _VLV postfix instead of prefix and regroupg
comments again so that the g4x warning is right next to those defines.
Also add a _G4X suffix for those special ones. Also cc stable.]
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- transactional execution
- lpp sampling support
In addition there is also a fix to the virtio-ccw guest driver. This will
enable future features
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=GbUg
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-20140117' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-queue
This deals with 2 guest features that need enablement in the kvm host:
- transactional execution
- lpp sampling support
In addition there is also a fix to the virtio-ccw guest driver. This will
enable future features
Verify that reserved fields in struct mlx5_ib_resize_cq are cleared
before continuing execution of the verb. This is required to allow
making use of this area in future revisions.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Do not continue with cleanup flow. If this ever happens we can check which
resources remained open.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current code attmepts to call ib_umem_get() even if the length is
zero, which causes a failure. Since the spec allows zero length work
queues, change the code so we don't call ib_umem_get() in those cases.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1. Fix derivation of sub-page index from the dma address in free_4k.
2. Fix the DMA address passed to dma_unmap_page by masking it properly.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use strings to display transport service or state of QPs. Use numeric
value for MTU of a QP.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Implement resize CQ which is a mandatory verb in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify CQ is used by ULPs like IPoIB to change moderation parameters. This
patch adds support in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Put a wmb() to make sure the doorbell record is visible to the HCA before we
hit doorbell.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use mlx5_core_warn(), which is the standard warning emitter function, instead
of pr_warn().
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Output structs are expected by firmware to be cleared when a command is called.
Clear the "out" struct instead of "dout" which is used only later.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The output size should be the sum of the core access reg output struct
plus the size of the specific register data provided by the caller.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use the possibly more efficient ether_addr_equal() instead of memcmp().
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The GSI QP type is compatible with and should be allowed to send data
to/from any UD QP. This was found when testing ibacm on the same node
as an SA.
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Building mem.o for 32 bits x86 triggers a GCC warning:
drivers/infiniband/hw/cxgb4/mem.c: In function '_c4iw_write_mem_dma_aligned':
drivers/infiniband/hw/cxgb4/mem.c:79:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Silence that warning by casting "&wr_wait" to unsigned long before
casting it to __be64. That's what _c4iw_write_mem_inline() already does.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a path in handle_vq() where kmem_cache_free() can be called
with pointer to a local variable. It can happen if vq_repbuf_alloc()
failed to allocate memory from cache and req is NULL.
The patch adds check if cache memory was allocated before freeing it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Svetlana Mavrina <another.karnil@gmail.com>
Reviewed-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Roland Dreier <roland@purestorage.com>
After booting without a working link, "ip link" shows:
5: mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc pfifo_fast
state DOWN qlen 256
...
7: mlx4_ib1.8003@mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc
pfifo_fast state DOWN qlen 256
...
Then after connecting and disconnecting the link, which should result
in exactly the same state as before, it shows:
5: mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc pfifo_fast
state DOWN qlen 256
...
7: mlx4_ib1.8003@mlx4_ib1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 2044 qdisc
pfifo_fast state LOWERLAYERDOWN qlen 256
...
Notice the (now correct) LOWERLAYERDOWN operstate shown for the
mlx4_ib1.8003 interface. Ideally the identical state would be shown
right after boot.
The problem is related to the calling of netif_carrier_off() in
network drivers. For a long time it was known that doing
netif_carrier_off() before registering the netdevice would result in
the interface's operstate being shown as UNKNOWN if the device was
brought up without a working link. This problem was fixed in commit
8f4cccbbd9 ('net: Set device operstate at registration time'), but
still there remains the minor inconsistency demonstrated above.
This patch fixes it by moving ipoib's call to netif_carrier_off() into
the .ndo_open method, which is where network drivers ordinarily do it.
With the patch when doing the same test as above, the operstate of
mlx4_ib1.8003 is shown as LOWERLAYERDOWN right after boot.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix the below "make W=1" build warning:
drivers/infiniband/core/iwcm.c: In function ‘destroy_cm_id’:
drivers/infiniband/core/iwcm.c:330: warning: variable ‘ret’ set but not used
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If addr is not a linklocal address, the code incorrectly fails to
return and ends up assigning the scope ID to the scope id of the
address, which is wrong. Fix by checking if it's a link local address
first, and immediately return 0 if not.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- FIFO event channels. Key advantages: support for over 100,000 events (2^17),
16 different event priorities, improved fairness in event latency through
the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with paravirtualized
disk and network, paravirtualized interrupts and timers, no emulated devices
of any kind (and thus no qemu), no BIOS or legacy boot — but instead of
requiring PV MMU, it uses the HVM hardware extensions to virtualize the
pagetables, as well as system calls and other privileged operations."
(from "The Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS4BmLAAoJEFjIrFwIi8fJ4SAH/iNGESowgMhfW64vRA8pBWq+
NRJpUjYjjwmbxpwoNl6NPwn15cIXFyc3sMtvvrDD3taRDyko2RFuT+NTjpO05xPh
d/cRpRXpXERHoiFgPf/WTp7ONBDhvPtHG0+BzJKwgqEIOUYXdbhD+gEjaVlFJScS
CAY68OLmk7XYMSZBNzPfKNbSCyhVgZF7wpaimK9lxZBKsFRCDIq6jIyrAsC8epIL
6V/V4l2S6lk/uUeGB6ULphYeINjI2kkpbSfCd1vyenLfWpVscc2o8uWEYFcZMAxy
V4HpsoseuqrfdDqgPfud3VgogdISvbkCvDfW85rzfDP4MWxei2mVHFtJ/gSBV+g=
=ToNG
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from Konrad Rzeszutek Wilk:
"Two major features that Xen community is excited about:
The first is event channel scalability by David Vrabel - we switch
over from an two-level per-cpu bitmap of events (IRQs) - to an FIFO
queue with priorities. This lets us be able to handle more events,
have lower latency, and better scalability. Good stuff.
The other is PVH by Mukesh Rathor. In short, PV is a mode where the
kernel lets the hypervisor program page-tables, segments, etc. With
EPT/NPT capabilities in current processors, the overhead of doing this
in an HVM (Hardware Virtual Machine) container is much lower than the
hypervisor doing it for us.
In short we let a PV guest run without doing page-table, segment,
syscall, etc updates through the hypervisor - instead it is all done
within the guest container. It is a "hybrid" PV - hence the 'PVH'
name - a PV guest within an HVM container.
The major benefits are less code to deal with - for example we only
use one function from the the pv_mmu_ops (which has 39 function
calls); faster performance for syscall (no context switches into the
hypervisor); less traps on various operations; etc.
It is still being baked - the ABI is not yet set in stone. But it is
pretty awesome and we are excited about it.
Lastly, there are some changes to ARM code - you should get a simple
conflict which has been resolved in #linux-next.
In short, this pull has awesome features.
Features:
- FIFO event channels. Key advantages: support for over 100,000
events (2^17), 16 different event priorities, improved fairness in
event latency through the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with
paravirtualized disk and network, paravirtualized interrupts and
timers, no emulated devices of any kind (and thus no qemu), no BIOS
or legacy boot — but instead of requiring PV MMU, it uses the HVM
hardware extensions to virtualize the pagetables, as well as system
calls and other privileged operations." (from "The
Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels"
* tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (52 commits)
xen/pvh: Set X86_CR0_WP and others in CR0 (v2)
MAINTAINERS: add git repository for Xen
xen/pvh: Use 'depend' instead of 'select'.
xen: delete new instances of __cpuinit usage
xen/fb: allow xenfb initialization for hvm guests
xen/evtchn_fifo: fix error return code in evtchn_fifo_setup()
xen-platform: fix error return code in platform_pci_init()
xen/pvh: remove duplicated include from enlighten.c
xen/pvh: Fix compile issues with xen_pvh_domain()
xen: Use dev_is_pci() to check whether it is pci device
xen/grant-table: Force to use v1 of grants.
xen/pvh: Support ParaVirtualized Hardware extensions (v3).
xen/pvh: Piggyback on PVHVM XenBus.
xen/pvh: Piggyback on PVHVM for grant driver (v4)
xen/grant: Implement an grant frame array struct (v3).
xen/grant-table: Refactor gnttab_init
xen/grants: Remove gnttab_max_grant_frames dependency on gnttab_init.
xen/pvh: Piggyback on PVHVM for event channels (v2)
xen/pvh: Update E820 to work with PVH (v2)
xen/pvh: Secondary VCPU bringup (non-bootup CPUs)
...
Like bonding, team as netdevice doesn't cross netns boundaries.
Team ports and team itself live in same netns.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like bridge, bonding as netdevice doesn't cross netns boundaries.
Bonding ports and bonding itself live in same netns.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user to identify easily what the attributes are related to. Change
the name of the group to "bonding_slave" to be similar to master which
is named "bonding".
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
A patch for fixing a race between queue selection and changing queues
was introduced in commit 92bb73ea2("tuntap: fix a possible race between
queue selection and changing queues").
The fix was to prevent the driver from re-reading the tun->numqueues
more than once within tun_select_queue() using ACCESS_ONCE().
We have been experiancing 'Divide-by-zero' errors in tun_net_xmit()
since we moved from 3.6 to 3.10, and believe that they come from a
simular source where the value of tun->numqueues changes to zero
between the first and a subsequent read of tun->numqueues.
The fix is a simular use of ACCESS_ONCE(), as well as a multiply
instead of a divide in the if statement.
Signed-off-by: Dominic Curran <dominic.curran@citrix.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Max Krasnyansky <maxk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
Pull HID updates from Jiri Kosina:
- quite some work on hid-sony driver in order to have DualShock 4
device properly supported, from Frank Praznik
- fixed support for suspending I2C conntected devices, from Mika
Westerberg
- regression fix for 0xff05 usage on Microsoft Ergonomy, from Jiri
Kosina
- support for Synaptics HD touchscreen, from AceLan Kao
- workaround for USB 3.0 problem for logitech-dj connected devices,
from Benjamin Tisssoires
- support for Logitech Dual Action pads, from Vitaly Katraew
- quite a few other assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (33 commits)
HID: sony: Use colors for the Dualshock 4 LED names
HID: sony: Add annotated HID descriptor for the Dualshock 4
HID: sony: Cache the output report for the Dualshock 4
HID: sony: Map gyroscopes and accelerometers to axes
HID: sony: Fix spacing in the device definitions.
HID: sony: Use standard output reports instead of raw reports to send data to the Dualshock 4.
HID: sony: Use separate identifiers for USB and Bluetooth connected Dualshock 4 controllers.
HID: hid-holtek-mouse: add new a070 mouse
HID: hid-sensor-hub: Fix buggy report descriptors
HID: logitech-dj: Fix USB 3.0 issue
HID: sony: Rename worker function
HID: sony: Add LED controls for the Dualshock 4
HID: sony: Add force-feedback support for the Dualshock 4
HID: hidraw: make comment more accurate and nicer
HID: sony: fix error return code
HID: input: fix input sysfs path for hid devices
HID: debug: add labels for some new buttons
HID: remove SIS entries from hid_have_special_driver[]
HID: microsoft: no fallthrough in MS ergonomy 0xff05 usage
HID: add support for SiS multitouch panel in the touch monitor LG 23ET83V
...
A lot of attention was paid to improving the thin-provisioning target's
handling of metadata operation failures and running out of space. A new
'error_if_no_space' feature was added to allow users to error IOs rather
than queue them when either the data or metadata space is exhausted.
Additional fixes/features include:
- a few fixes to properly support thin metadata device resizing
- a solution for reliably waiting for a DM device's embedded kobject to
be released before destroying the device
- old dm-snapshot is updated to use the dm-bufio interface to take
advantage of readahead capabilities that improve snapshot activation
- new dm-cache target tunables to control how quickly data is promoted
to the cache (fast) device
- improved write efficiency of cluster mirror target by combining
userspace flush and mark requests
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS4GClAAoJEMUj8QotnQNacdEH/2ES5k5itUQRY9jeI+u2zYNP
vdsRTYf+97+B3jpRvpWbMt4kxT2tjaQbkxJ+iKRHy2MBLFUgq8ruH1RS/Q5VbDeg
6i6ol8mpNxhlvo/KTMxXqRcWDSxShiMfhz2lXC2bJ7M4sP/iiH85s4Pm4YQ59jpd
OIX7qj36m/cV/le9YQbexJEEsaj+3genbzL26wyyvtG/rT9fWnXa7clj2gqTdToG
YCEBCRf5FH9X6W/Oc50nMw5n2dt/MRmPre/MAlOjemeaosB0WJiKaswM25rnvHp0
JnhxQ2K2C5KIKAWIfwPOImdb9zWW7p1dIRLsS8nHBUQr0BF5VRkmvpnYH4qBtcc=
=e7e0
-----END PGP SIGNATURE-----
Merge tag 'dm-3.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper changes from Mike Snitzer:
"A lot of attention was paid to improving the thin-provisioning
target's handling of metadata operation failures and running out of
space. A new 'error_if_no_space' feature was added to allow users to
error IOs rather than queue them when either the data or metadata
space is exhausted.
Additional fixes/features include:
- a few fixes to properly support thin metadata device resizing
- a solution for reliably waiting for a DM device's embedded kobject
to be released before destroying the device
- old dm-snapshot is updated to use the dm-bufio interface to take
advantage of readahead capabilities that improve snapshot
activation
- new dm-cache target tunables to control how quickly data is
promoted to the cache (fast) device
- improved write efficiency of cluster mirror target by combining
userspace flush and mark requests"
* tag 'dm-3.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (35 commits)
dm log userspace: allow mark requests to piggyback on flush requests
dm space map metadata: fix bug in resizing of thin metadata
dm cache: add policy name to status output
dm thin: fix pool feature parsing
dm sysfs: fix a module unload race
dm snapshot: use dm-bufio prefetch
dm snapshot: use dm-bufio
dm snapshot: prepare for switch to using dm-bufio
dm snapshot: use GFP_KERNEL when initializing exceptions
dm cache: add block sizes and total cache blocks to status output
dm btree: add dm_btree_find_lowest_key
dm space map metadata: fix extending the space map
dm space map common: make sure new space is used during extend
dm: wait until embedded kobject is released before destroying a device
dm: remove pointless kobject comparison in dm_get_from_kobject
dm snapshot: call destroy_work_on_stack() to pair with INIT_WORK_ONSTACK()
dm cache policy mq: introduce three promotion threshold tunables
dm cache policy mq: use list_del_init instead of list_del + INIT_LIST_HEAD
dm thin: fix set_pool_mode exposed pool operation races
dm thin: eliminate the no_free_space flag
...
Also make nv_lockvgac work for nv50+ devices. This should fix
IO_CONDITION and related VBIOS opcodes that read/write the crtc regs.
See https://bugs.freedesktop.org/show_bug.cgi?id=60680
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not holding the mutex potentially causes corruption of the kernel
channel when page flipping.
Cc: stable@vger.kernel.org #3.13
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Seen on Titan. NFI what the condition to switch this on is yet, and,
hardcoding it to on currently causes master to report unknown intr
with a mask of 0x08002000.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Still essentially a struct of magic values with magic names and unknown
purposes. But, we will shortly need to be able to mix and match bits of
the previous and next configurations to do a transition reclock, as such,
we can no longer directly use the vbios data with any ease.
This is probably nicer anyway in the long run, for a few reasons.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Compute code in mesa triggers one of these, hanging the engine. Let's
at least ack the request for now to avoid the hang.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some firmware images may be large (64K), so using kmalloc memory is
inappropriate for them. Use vmalloc instead, to avoid high-order
allocation failures.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org
Now that nouveau_bo.c can handle sync when it actually needs to, we can
remove this and avoid a double semaphore acquire when syncing in the
command submission path.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Moves bo's to TTM_PL_TT for BAR mapping, to hide tiling from user.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit de7b7d59d5 introduced tiled GART, but a linear copy is
still performed. This may result in errors on eviction, fix it by
checking tiling from memtype.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@vger.kernel.org #3.10+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pretty much everywhere had to make the decision which to use, so it
makes a lot more sense to just have one entrypoint decide the path
to take instead.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
If the new primay is not matching any slave in the bond, the bond should
record it to params, clean the primary slave and select a new active slave.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per suggestion from Eric W. Biederman, vxlan should be using
{un,}register_pernet_subsys() instead of {un,}register_pernet_device()
to ensure the vxlan_net structure is initialized before and cleaned
up after all network devices in a given network namespace i.e. when
dealing with network notifiers. This is similarly handeled already in
commit 91e2ff3528 ("net: Teach vlans to cleanup as a pernet subsystem")
and, thus, improves upon fd27e0d44a ("net: vxlan: do not use vxlan_net
before checking event type"). Just as in 91e2ff3528, we do not need
to explicitly handle deletion of vxlan devices as network namespace
exit calls dellink on all remaining virtual devices, and
rtnl_link_unregister() calls dellink on all outstanding devices in that
network namespace, so we can entirely drop the pernet exit operation
as well. Moreover, on vxlan module exit, rcu_barrier() is called by
netns since commit 3a765edadb ("netns: Add an explicit rcu_barrier
to unregister_pernet_{device|subsys}"), so this may be omitted. Tested
with various scenarios and works well on my side.
Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set is a lot of driver updates for qla4xxx, bfa, hpsa, qla2xxx. It
also removes the aic7xxx_old driver (which has been deprecated for nearly a
decade) and adds support for deadlines in error handling.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJS4AfxAAoJEDeqqVYsXL0M8DAIAKRtc9+hy2zsratyvHxxZlz4
6tdvT/4dLTXbIS7EFHmdVb09G5791Pj2jx2PAza/zFDSzgMyL8reXjXpDtCQBvsG
U9CKAGAfJi/vD3QSez2qh0SyvIfCHjatlU3IsM/g+5iFcIOO9+LMJuRlw3qtVqOZ
iQQBATH8cuVW7k1YRHXS5xAO8cVCEYBPuuz0UreVnZijTV5lsRFaObaq8r7S7yVM
4F5eSb5lcgZZLDMDMB0E2KHq12QoLiLQy/ahCqAL1od41v+P90BHC4cIu8jkdB0l
nUYp8vHkmsM82L3xxK9HglcZvJ94fkz6n1gwULl2dTNSYldUnXc/xmocbt0KMf8=
=yko3
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set is a lot of driver updates for qla4xxx, bfa, hpsa,
qla2xxx. It also removes the aic7xxx_old driver (which has been
deprecated for nearly a decade) and adds support for deadlines in
error handling"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (75 commits)
[SCSI] hpsa: allow SCSI mid layer to handle unit attention
[SCSI] hpsa: do not require board "not ready" status after hard reset
[SCSI] hpsa: enable unit attention reporting
[SCSI] hpsa: rename scsi prefetch field
[SCSI] hpsa: use workqueue instead of kernel thread for lockup detection
[SCSI] ipr: increase dump size in ipr driver
[SCSI] mac_scsi: Fix crash on out of memory
[SCSI] st: fix enlarge_buffer
[SCSI] qla1280: Annotate timer on stack so object debug does not complain
[SCSI] qla4xxx: Update driver version to 5.04.00-k3
[SCSI] qla4xxx: Recreate chap data list during get chap operation
[SCSI] qla4xxx: Add support for ISCSI_PARAM_LOCAL_IPADDR sysfs attr
[SCSI] libiscsi: Add local_ipaddr parameter in iscsi_conn struct
[SCSI] scsi_transport_iscsi: Export ISCSI_PARAM_LOCAL_IPADDR attr for iscsi_connection
[SCSI] qla4xxx: Add host statistics support
[SCSI] scsi_transport_iscsi: Add host statistics support
[SCSI] qla4xxx: Added support for Diagnostics MBOX command
[SCSI] bfa: Driver version upgrade to 3.2.23.0
[SCSI] bfa: change FC_ELS_TOV to 20sec
[SCSI] bfa: Observed auto D-port mode instead of manual
...
plat/regs-nand.h is used only by S3C2410 nand driver. Since there
are no other users, merge this file into the driver code to remove
platform dependency. While at it also remove unused macros.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the mode is set with 16bpp on QEMU, the output gets totally broken.
The culprit is the bogus register values set for 16bpp, which was likely
copied from from a wrong place.
Addresses https://bugzilla.novell.com/show_bug.cgi?id=799216
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: David Airlie <airlied@linux.ie>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 8116188fde ("nouveau/acpi: hook up to the MXM method for mux
switching.") broke the build on non-x86 architectures due to the new
dependency on MXM and MXM being an x86 platform driver.
It built previously since the vga switcheroo registration routines were
zereod out on !X86. The code was built in but unused.
This patch makes all of the DSM code depend on CONFIG_VGA_SWITCHEROO,
allowing it to build on non-x86 and shrinking the module size as well.
[rdunlap@infradead.org: fix build eror when VGA_SWITCHEROO is not enabled]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds the necessary changes so slaves would use
the new bonding option API. Also move the option to its own set function
in bond_options.c and fix some style errors.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary changes so lp_interval would use
the new bonding option API.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary changes so resend_igmp would use
the new bonding option API.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary changes so all_slaves_active would use
the new bonding option API.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary changes so queue_id would use
the new bonding option API. Also move it to its own set function in
bond_options.c and fix some style errors.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary changes so active_slave would use
the new bonding option API. Also some trivial/style fixes.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary changes so use_carrier would use
the new bonding option API.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary changes so primary_reselect would use
the new bonding option API.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary changes so primary would use
the new bonding option API.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corey Minyard
Xie XiuQi
Michael Opdenacker
Linus Torvalds
Stanislaw Gruszka
Sagi Grimberg
Nicholas Bellinger
Gavin Shan
Rafał Miłecki
Hauke Mehrtens
Wolfram Sang
John W. Linville
Paul Gortmaker
Jean Delvare
Shane Huang
Daniel Vetter
Martin Schwidefsky
Evgeny Boger
Micky Ching
Andreas Werner
Geert Uytterhoeven
Stephen Warren
Sachin Kamat
Andrew Morton
Duan Jiong
Heiko Stuebner
Jingoo Han
Alexander Shiyan
Fabio Estevam
Laxman Dewangan
Ard Biesheuvel
Dan Carpenter
David Howells
Fabian Frederick
Himanshu Madhani
Manish chopra
Sucheta Chakraborty
Nikolay Aleksandrov
Ben Hutchings
Or Gerlitz
Mugunthan V N
Kent Overstreet
Sujith Manoharan
Roman Dubtsov
ZHAO Gang
Andreas Fenkart
Greg Kroah-Hartman
Dmitry Torokhov
Adrian Hunter
Thierry Reding
Rob Herring
Sourav Poddar
Mark Brown
Florian Fainelli
Todd Previte
Paolo Bonzini
Roland Dreier
Eli Cohen
Haggai Eran
Ding Tianhong
Ira Weiny
Paul Bolle
Wei Yongjun
Svetlana Mavrina
Michal Schmidt
Somnath Kotur
Weilong Chen
Jiri Pirko
Dominic Curran
Ben Skeggs
Ilia Mirkin
Maarten Lankhorst
Daniel Borkmann
Takashi Iwai
Jeff Mahoney
Dave Airlie