Add the 3 sdhci devices that are available on Harmony as
platform devices. Two go to slots (one 4-lane, one 8-lane),
and one goes to onboard wifi.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Add a common location to register resources for used on-chip devices
that are commonly configured on boards. Devices will be added to this file
as more drivers are added that can make use of them.
This is based on work contributed by several people, most of it from
Colin Cross and Erik Gilling.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Move harmony over to use the new gpio config table instead of having
separate settings in various parts of the code.
(The tegra sdhci driver should have the tegra_gpio_* ops removed, but
that will be done separately from this change.)
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Erik Gilling <konkers@android.com>
To give one place to setup the pins that are used as GPIOs instead
of as their pinmuxed functions. Specifying enabled as false explicitly
disables the gpio mode of that pin (if left on by firmware).
This should remove the need for calling these from specific drivers and
thus reduce tegra-specific code from them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Erik Gilling <konkers@android.com>
The option isn't terribly useful on other ARM platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Enable the cpu, emc (memory controller) and csite (debug and
trace controller) clocks during init to prevent them from
being disabled by the bootloader clock disabling code.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Enable the timer and rtc clocks to prevent them being
turned off by the bootloader clock disabling code.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Move tegra_common_init to tegra_init_early, and set it
as the init_early entry in the machine struct.
Initializes the clocks earlier so that timers can enable
their clocks.
Also reorders the members in the Harmony and Trimslice
boards' machine structs to match the order they are
called in.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Peripheral clocks that have no clock enable bit in the
enable registers have their clk_num set to 0. Bit 0
in the clock enable registers is the CPU clock.
Prevent disables on these peripheral clocks from
accidentally disabling the CPU clock.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Call the clock's round_rate op, if it exists, before calling
the set_rate op. This will help later when dvfs is added,
dvfs needs to know what the final rate will be before the
frequency changes.
Also requires fixes to the round rate functions to ensure
calling round rate and then set rate will not cause the
frequency to be rounded down twice. When picking clock
divider values, the clock framework picks the closest
frequency that is lower than the requested frequency. If
the new frequency calculated from the divider value is
rounded down, and then passed to set_rate, it will get
rounded down again, possibly resulting in a frequency two
steps lower than the original requested frequency.
Fix the problem by rounding up when calculating the frequency
coming out of a clock divider, so if that frequency is
requested again, the same divider value will be picked.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Some peripheral clocks share enable bits. Refcount the enables so
that calling clk_disable on one clock will not turn off another
clock.
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Correct max rates for pclk and sclk (Originally fixed by
Dima Zavin <dima@android.com>)
Correct max rate for plla (Originally fixed by
Stephen Warren <swarren@nvidia.com>)
Remove unnecessary no-op set_rate on audio clocks
Add clock lookup entries for grhost, bsea, and vde clocks
Update clock clookup entries for vcp, bsea, and vde clocks
Add shared clock entries for sclk and emc
Add a virtual cop clock to provide a reset op (Originally fixed by
Dima Zavin <dima@android.com>)
Pass set_rate on super clocks through to parent
Fix pllx frequency table entry for 608 MHz
Remove incorrect plla frequency table entries
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The PLLP registers are now being restored by the low-level resume code,
and the CPU may be running off PLLP, so don't touch them during clock
resume.
Save plld, plls, pllu, and audio clock during suspend (originally
fixed by Mayuresh Kulkarni <mkulkarni@nvidia.com>)
The lock time for plld is 1000 us, so increase the delay after
setting the PLLs.
Add a BUG_ON to ensure the size of the suspend context area is
correct.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The SDMMC controllers have extra bits in the clock source
register that adjust the delay between the clock and data
to compenstate for delays on the PCB. The values need to
be set from the clock code so the clock can be locked
during the read-modify-write on the clock source register.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Adjusts the minimum memory frequency when the cpu frequency
changes. The values are currently hardcoded to a reasonable
default. If memory frequency scaling is not enabled this
patch will have no effect.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Add clock ops on the emc peripheral clock that call into the
emc driver to update the memory controller registers for the
new frequency. Tegra has an interlock between the clock
controller and the memory controller that prevents the new
register values from taking effect until the clock frequency
update occurs.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The frequency memory bus on Tegra can be adjusted without
disabling accesses to memory by updating the memory
configuration registers from a per-board table, and then
changing the clock frequency. The clock controller and
memory controller have an interlock that prevents the
new memory registers from taking effect until the
clock frequency change.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Remove unnecessary uses of #ifdef CONFIG_DEBUG_FS
Convert bool assignments from 1 to true
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Some clocks may have multiple downstream users that need to request a
higher clock rate. Shared bus clocks provide a unique shared_bus_user
clock to each user. The frequency of the bus is set to the highest
enabled shared_bus_user clock, with a minimum value set by the
shared bus. Drivers can use clk_enable and clk_disable to enable
or disable their requirement, and clk_set_rate to set the minimum rate.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
During cpu frequency changes, take an extra reference to pllx so
that it doesn't turn off and on while the cpu is temporarily on
pllp. If the cpu is moved to pllp permanently, pllx will be
turned off.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Give each clock its own lock, and remove all lock traversals from
parent to child clocks to prevent AB-BA deadlocks.
This brings the locking in line with the common struct clk
patches and should make conversion simple.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Creates a union of a struct for each type of clock to reduce memory
usage and clarify which members are used by all clocks and which are
used by a single type.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Make the static clocks look more like the array of clocks
so they can all be initalized with the same helper function.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The existing version did not extend well to core dvfs, drop it
for now until the new clk api with clk_prepare and clk_unprepare
is ready and non-atomic clocks are possible.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
The PLL lock bits are not reliable, use per-PLL timeouts instead.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Drop the unnecessary pr_debug calls to avoid having to maintain them.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
When updating the CPU PLL frequency, keeping the PLL enabled avoids
ramping the PLL all the way down and back up again. Remove the BUG_ON
in tegra2_pll_clk_set_rate to allow the rate to change while the PLL
is enabled.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Add a new 'reset' clk op. This can be provided for any clock,
not just peripherals.
Signed-off-by: Dima Zavin <dima@android.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
This seems to be a regression in 2.6.37.
We cannot use writel() here since the resulting wmb() calls l2x0_cache_sync()
which uses a spinlock and L1 cache may be off at this point.
http://lists.infradead.org/pipermail/linux-arm-kernel/2011-February/041909.html
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Colin Cross <ccross@android.com>
If a request already in the queue is passed to tegra_dma_enqueue_req,
tegra_dma_req.node->{next,prev} will end up pointing to itself instead
of at tegra_dma_channel.list, which is the way a the end-of-list
should be set up. When the DMA request completes and is list_del'd,
the list head will still point at it, yet the node's next/prev will
contain the list poison values. When the next DMA request completes,
a kernel panic will occur when those poison values are dereferenced.
This makes the DMA driver more robust in the face of buggy clients.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Add Fn keymap support to allow for internal processing of Fn keys.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This uncouple PHYS_OFFSET from the platform definitions, thereby
facilitating run-time computation of the physical memory offset.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sometimes, due to high interrupt latency in the continuous mode
of DMA transfer, the half buffer complete interrupt is handled
after DMA has transferred the full buffer. When this is detected,
stop DMA immediately and restart with the next buffer if the next
buffer is ready.
originally fixed by Victor(Weiguo) Pan <wpan@nvidia.com>
In place of using the simple spin_lock()/spi_unlock() in the
interrupt thread, using the spin_lock_irqsave() and
spin_unlock_irqrestore(). The lock is shared between the normal
process context and interrupt context.
originally fixed by Laxman Dewangan (ldewangan@nvidia.com)
The use of shadow registers caused memory corruption at physical
address 0 because the enable bit was not shadowed, and assuming it
needed to be set would enable an unconfigured dma block. Most of the
register accesses don't need to know the previous state of the
registers, and the few places that do need to modify only a few bits
in the registers are the same ones that were sometimes incorrectly
setting the enable bit. This patch convert tegra_dma_update_hardware
to set the entire register, and the other users to read-modify-write,
and drops the shadow registers completely.
Also fixes missing locking in tegra_dma_allocate_channel
Signed-off-by: Colin Cross <ccross@android.com>
On Tegra, calling clk_set_rate on the CPU clock may call into the
regulator API. If the regulator driver that controls the CPU
voltage rail has been suspended, this can lead to attempted
communication with a hardware block that has already been turned
off.
Adds a SUSPEND_PREPARE notification hook to drop the frequency to
the lowest possible during suspend.
Also adds 216MHz (off of PLLP) as the lowest CPU frequency, which
allows PLLX to be turned off.
Signed-off-by: Colin Cross <ccross@android.com>
Adds gart, hdmi, avp, host1x, and pwm controllers to mach/iomap.h
Signed-off-by: Gary King <gking@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Implement read_persistent_clock by reading the Tegra RTC
registers that stay running during suspend.
Save and restore the timer configuration register in
suspend.
Signed-off-by: Colin Cross <ccross@android.com>
Adds missing drive pingroups, saves all drive pingroups in
suspend, and restores the pinmux registers in the proper order.
Signed-off-by: Gary King <gking@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Save and restore pll and osc state during suspend
Add digital audio clocks
Update clk dev associations
Correct max clock frequencies
Add pll_p as additional cpu clock state
Add values to plld table
Fix register offset for sdmmc4 clock
Add blink timer to tegra2_clocks
Signed-off-by: Colin Cross <ccross@android.com>
Add fields to describe all the audio-related GPIOs on Harmony, except for
the codec's GPIO IRQ, which will be passed in its i2c_board_info.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A future patch will export gic_mask_irq and gic_unmask_irq.
Rename the pointers in arch/arm/mach-tegra/irq.c to avoid
a compile error.
Signed-off-by: Colin Cross <ccross@android.com>
Commit 37337a8d5e, "ARM: tegra: irq_data
conversion." missed changing one reference to 'irq' in the function
tegra_gpio_irq_set_type(). This patch fixes the build error.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - pass touch resolution to clients through input_absinfo
Input: wacom - add 2 Bamboo Pen and touch models
Input: sysrq - ensure sysrq_enabled and __sysrq_enabled are consistent
Input: sparse-keymap - fix KEY_VSW handling in sparse_keymap_setup
Input: tegra-kbc - add tegra keyboard driver
Input: gpio_keys - switch to using request_any_context_irq
Input: serio - allow registered drivers to get status flag
Input: ct82710c - return proper error code for ct82c710_open
Input: bu21013_ts - added regulator support
Input: bu21013_ts - remove duplicate resolution parameters
Input: tnetv107x-ts - don't treat NULL clk as an error
Input: tnetv107x-keypad - don't treat NULL clk as an error
Fix up trivial conflicts in drivers/input/keyboard/Makefile due to
additions of tc3589x/Tegra drivers
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@google.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for the internal matrix keyboard controller for
Nvidia Tegra platforms.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: fix missing branch in __error_a
ARM: fix /proc/$PID/stack on SMP
ARM: Fix build regression on SA11x0, PXA, and H720x targets
ARM: 6625/1: use memblock memory regions for "System RAM" I/O resources
ARM: fix wrongly patched constants
ARM: 6624/1: fix dependency for CONFIG_SMP_ON_UP
ARM: 6623/1: Thumb-2: Fix out-of-range offset for Thumb-2 in proc-v7.S
ARM: 6622/1: fix dma_unmap_sg() documentation
ARM: 6621/1: bitops: remove condition code clobber for CLZ
ARM: 6620/1: Change misleading warning when CONFIG_CMDLINE_FORCE is used
ARM: 6619/1: nommu: avoid mapping vectors page when !CONFIG_MMU
ARM: sched_clock: make minsec argument to clocks_calc_mult_shift() zero
ARM: sched_clock: allow init_sched_clock() to be called early
ARM: integrator: fix compile warning in cpu.c
ARM: 6616/1: Fix ep93xx-fb init/exit annotations
ARM: twd: fix display of twd frequency
ARM: udelay: prevent math rounding resulting in short udelays
e3d9c625 (ARM: CPU hotplug: fix hard-coded control register constants)
changed the wrong constants in the hotplug assembly code. Fix this.
Reported-by: viresh kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SDHCI driver for Tegra. This driver plugs in as a new variant of
sdhci-pltfm, using the platform data structure passed in to specify the
GPIOs to use for card detect, write protect and card power enablement.
Original driver (of which only the header file is left):
Signed-off-by: Yvonne Yip <y@palm.com>
The rest, which has been rewritten by now:
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert tegra to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
tegra_clocksource_read should not use cnt32_to_63, wrapping is
already handled in the clocksource code. Move the cnt32_to_63
into the sched_clock function, and replace the use of clocksource
mult and shift with a multiplication by 1000 to convert us to ns.
Acked-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original scheme for reporting spurious wakeups was broken - it
tried to use printk() from a context which wasn't coherent with the
other CPUs, which risks corrupting the printk() data.
Fix this by noting the number spurious wakeups, and only report them
when we are properly woken - when we will be coherent with the rest
of the system.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With "ARM: CPU hotplug: remove bug checks in platform_cpu_die()", we
now do not use hard_smp_processor_id(), we no longer need to read the
hardware processor ID. Remove the include providing this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
platform_cpu_die() is entered from the CPU's own idle thread, which
can not be migrated to other CPUs. Moreover, the 'cpu' argument
comes from the thread info, which will always be the 'current'
CPU. So remove this useless bug check.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We always need to wait for the dying CPU to reach a safe state before
taking it down, irrespective of the requirements of the platform.
Move the completion code into the ARM SMP hotplug code rather than
having each platform re-implement this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All platforms call trace_hardirqs_off() in their secondary startup code,
so move this into the core SMP code - it doesn't need to be in the
per-platform code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a certain amount of smp_prepare_cpus() which doesn't belong
in the platform support code - that is, code which is invariant to the
SMP implementation. Move this code into arch/arm/kernel/smp.c, and
add a platform_ prefix to the original function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Milo is an old boot loader, which is no longer relevant for these
platforms. References to it are misleading. Move the code out
of poke_milo(), and remove references to milo in comments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
scu_get_core_count() never returns zero cores, so we don't need to
check and correct if ncores is zero.
Tegra was missing the check against NR_CPUS, leading to a potential
bitfield overflow if this becomes the case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a standard get_irqnr_preamble assembler macro for platforms
to use, which retrieves the base address of the GIC CPU interface
from gic_cpu_base_addr. Allow platforms to override this by defining
HAVE_GET_IRQNR_PREAMBLE.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to re-pass the base address for the CPU interfaces to the
GIC for secondary CPUs, as it will never be different from the boot CPU
- and even if it was, we'd overwrite the boot CPU's base address.
Get rid of this argument, and rename to gic_secondary_init().
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide gic_init() which initializes the GIC distributor and current
CPU's GIC interface for the boot (or single) CPU.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Defining iounmap() with arguments prevents it from being used as a
function pointer, causing platforms to work around this. Instead,
define it to be a simple macro.
Do the same for __arch_io(re|un)map too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the Tegra subarchitecture.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 0ea1293009 ("arm: return both physical and virtual addresses
from addruart") took out the test for MMU on/off but didn't switch the
ldr instructions to no longer be conditionals based on said test.
Fix that.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to use smp_cross_call() to trigger a number of different
software generated interrupts, rather than combining them all on one
SGI. Recover the SGI number via do_IPI.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
smp_cross_call_done() was removed long ago (see 78d236c - remove useless
smp_cross_call_done()). Remove those which have been subsequently
merged.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
CC: Olof Johansson <olof@lixom.net>
CC: Gary King <GKing@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Change-Id: Ibd0bcd46895eb88952b9db29e1f68572d39aae01
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Russell King <linux@arm.linux.org.uk>
CC: Gary King <GKing@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
The APB DMA block handles DMA transfers to and from some peripherals
in the Tegra SOC. It reads from sequential addresses on the memory
bus, and writes repeatedly to the same address on the APB bus.
Two transfer modes are supported, oneshot for transferring a known
size to or from a peripheral, and continuous for streaming data.
In continuous mode, a callback occurs when the buffer is half full
to allow the existing data to be handled and a new request queued.x
v2 changes:
dma API no longer uses PTR_ERR
Signed-off-by: Erik Gilling <konkers@android.com>
Signed-off-by: Colin Cross <ccross@android.com>
Implement cpufreq support for the Tegra SOC. DVFS is handled by the
core virtual cpu clock. The frequencies of the two cores are tied
together, the highest frequency requested by either core determines
the actual frequency.
Signed-off-by: Colin Cross <ccross@android.com>
- Add drivers to clock lookup table
- Add new pll_m entries
- Support I2C U16 divider
- Fix rate reporting on 32.768kHz clock
- Call propagate rate only if set_rate succeeds
- Add support for audio_sync clock
- Add 24MHz to PLLA frequency list
- Correct i2s1/2/spdifout mux
- Add suspend support
- Fix enable/disable parent clocks in set_parent
- Add max_rate parameter to all clocks
- DVFS support
- Add virtual cpu clock with dvfs
- Support clk_round_rate
- Fix requesting very high periph frequencies
- Add quirks for PLLU:
PLLU is slightly different from the rest of the PLLs. The
lock enable bit is at bit 22 instead of 18 in the MISC
register, and the post divider field is a single bit with
reversed values from other PLLs.
- Simplify recalculating clock rates
- Fix UART divider flags
- Remove unused clock ops
Signed-off-by: Colin Cross <ccross@android.com>
The Tegra SOC contains fuses to identify the CPU type and
bin, and a unique id. The CPU info is required to determine
the correct voltages for each cpu and core frequency.
Signed-off-by: Colin Cross <ccross@android.com>
- the reset values for some pin groups in the tegra pin mux can result in
functional errors due to conflicting with actively-configured pin groups
muxing from the same controller. this change adds a known safe, non-
conflicting mux for every pin group, which can be used on platforms
where the pin group is not routed to any peripheral
- also add each pin group's I/O voltage rail, to enable platform code to
map from the pin groups used by each interface to the regulators used
for dynamic voltage control
- add routines to individually configure the tristate, pin mux and pull-
ups for a pingroup_config array, so that it is possible to program
individual values at run-time without modifying other values.
this allows driver power-management code to reprogram individual
interfaces into lower power states during idle / suspend, or to
reprogram the pin mux to support multiple physical busses per
internal controller (e.g., sharing a single I2C or SPI controller
across multiple pin groups)
- move chip-specific data like pingroups and drive-pingroups
out of the common code and into chip-specific code
- fix debug output for group with no pullups
- add a TEGRA_MUX_SAFE function. Setting a pingroup to TEGRA_MUX_SAFE
will automatically select a mux setting that is guaranteed not to
conflict with any of the hardware blocks.
Signed-off-by: Gary King <gking@nvidia.com>
mirror IRQ enable and disable operations on the legacy PPI system
interrupt controller, since the legacy controller is responsible
for responding to wakeup interrupts when the CPU is in LP2 idle mode
save the irq controller state on suspend and restore on resume
Signed-off-by: Gary King <gking@nvidia.com>
The "legacy irq controller" duplicates the functionality of the GIC,
but remains powered during the cpu suspend and idle modes that power
down the CPU and the GIC.
Signed-off-by: Colin Cross <ccross@android.com>
Add missing io address map entries from datasheet.
Add the IRAM area to the statically mapped io regions.
Correct the onewire, USB, and statmon addresses
Signed-off-by: Colin Cross <ccross@android.com>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Silences following build warning:
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:644: warning: format '%08lx' expects type 'long
unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@google.com>
The patch "ARM: Remove DISCONTIGMEM support" removed the node id from
the meminfo struct and the PHYS_TO_NID macro, causing compilation errors:
arch/arm/mach-tegra/board-harmony.c: In function 'tegra_harmony_fixup':
arch/arm/mach-tegra/board-harmony.c:94: error: 'struct membank' has no member named 'node'
arch/arm/mach-tegra/board-harmony.c:94: error: implicit declaration of function 'PHYS_TO_NID'
arch/arm/mach-tegra/board-harmony.c:97: error: 'struct membank' has no member named 'node'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@google.com>
v2: fixes from Russell King
- include linux/io.h instead of mach/io.h
v3: fixes from Linus Walleij
- remove /16 * 16 from UART clock
v3:
- Fix checkpatch issues
- make board init calls explicit
- use clock init table to set clocks
- remove panel
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Erik Gilling <konkers@android.com>
v2: fixes from Russell King
- include linux/io.h instead of asm/io.h
v3:
- Add drive strength controls
- Replace typedef enums with plain enums
Signed-off-by: Erik Gilling <konkers@android.com>
Signed-off-by: Colin Cross <ccross@android.com>
v2: fixes from Mike Rapoport:
- move gpio-names.h to arch/arm/mach-tegra
fixes from Russell King
- include linux/io.h and linux/gpio.h instead of asm/io.h
and asm/gpio.h
additional changes:
- add macros to convert between irq and gpio numbers for platform data
- change for_each_bit to for_each_set_bit in gpio.c
v3:
- minor bugfixes
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Erik Gilling <konkers@android.com>
v2: fixes from Russell King:
- include linux/io.h instead of asm/io.h
fixes from Gary King:
- remove extra (and incorrect) irq definitions
- use timer 3 instead of timer 1 for compatibility with other drivers
- fix typo that disabled oneshot mode
v3:
- Implement sched_clock
- Fix checkpatch issues
fixes from Gary King:
- Fix incorrect cycles calculation
- Fix min_delta_ns assignment
fixes from Linus Walleij:
- use calc_mult_shift() instead of hard coding values
Signed-off-by: Colin Cross <ccross@android.com>
v2: fixes from Russell King:
- include linux/io.h instead of asm/io.h
- fix whitespace in Kconfig
- Use spin_lock_init to initialize lock
- Return -ENOSYS instead of BUG for unimplemented clock ops
- Use proper return values in tegra2 clock ops
additional changes:
- Rename some clocks to match dev_ids
- add rate propagation
- add debugfs entries
- add support for clock listed in clk_lookup under multiple dev_ids
v3:
- Replace per-clock locking with global clock lock
- Autodetect clock state on init
- Let clock dividers pick next lower possible frequency
- Add support for clock init tables
- Minor bug fixes
- Fix checkpatch issues
Signed-off-by: Colin Cross <ccross@android.com>
v2: fixes from Russell King
- include linux/io.h instead of asm/io.h and mach/io.h
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Erik Gilling <konkers@android.com>
v2: Fixes from Mike Rapoport
- remove unused header files (mach/dma.h and mach/nand.h)
- remove tegra 1 references from Makefile.boot
v2: fixes from Russell King
- remove mach/io.h include from mach/iomap.h
- fix whitespace in Kconfig
v2: from Colin Cross
- fix invalid immediate in debug-macro.S
v3:
- allow selection of multiple boards
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Erik Gilling <konkers@android.com>
Olof Johansson
Mark Brown
Stephen Warren
Colin Cross
Dima Zavin
Simon Glass
Rakesh Iyer
Russell King
Mike Rapoport
Gary King
Linus Torvalds
Grant Likely
Lennert Buytenhek
Magnus Damm
Jean-Christop PLAGNIOL-VILLARD
Zimny Lech
Nicolas Pitre
Jeremy Kerr
Erik Gilling