[ Upstream commit 09f688f071 ]
The reg member of struct raspberrypi_pwm_prop is a little endian 32 bit
quantity. Explicitly convert the (native endian) value to little endian
on assignment as is already done in raspberrypi_pwm_set_property().
This fixes the following sparse warning:
drivers/pwm/pwm-raspberrypi-poe.c:69:24: warning: incorrect type in initializer (different base types)
drivers/pwm/pwm-raspberrypi-poe.c:69:24: expected restricted __le32 [usertype] reg
drivers/pwm/pwm-raspberrypi-poe.c:69:24: got unsigned int [usertype] reg
Fixes: 79caa362ea ("pwm: Add Raspberry Pi Firmware based PWM bus")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e3b07ca5c ]
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
Fixes: af66b3c093 ("pwm: Add LP3943 PWM driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7079b3483a ]
If device_register() fails, device_unregister() should not be called
because it will free some resources that are not allocated.
put_device() should be used instead.
Fixes: 308ee87a2f ("staging: fieldbus: anybus-s: support HMS Anybus-S bus")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/5401a519608d6e1a4e7435c20f4f20b0c5c36c23.1650610082.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 424bef51fa ]
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 8934d3e4d0 ("usb: musb: omap2430: Don't use omap_get_control_dev()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220309111033.24487-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b92ffb1edd ]
The function rio_karam_init() should return -ENOMEM instead of
value 0 (USB_STOR_TRANSPORT_GOOD) when allocation fails.
Similarly, it should return -EIO when rio_karma_send_command() fails.
Fixes: dfe0d3ba20 ("USB Storage: add rio karma eject support")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://lore.kernel.org/r/20220412144359.28447-1-linma@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d088fabace ]
The function documentation of usb_set_configuration says that its
callers should hold the device lock. This lock is held for all
callsites except tweak_set_configuration_cmd. The code path can be
executed for example when attaching a remote USB device.
The solution is to surround the call by the device lock.
This bug was found using my experimental own-developed static analysis
tool, which reported the missing lock on v5.17.2. I manually verified
this bug report by doing code review as well. I runtime checked that
the required lock is not held. I compiled and runtime tested this on
x86_64 with a USB mouse. After applying this patch, my analyser no
longer reports this potential bug.
Fixes: 2c8c981589 ("staging: usbip: let client choose device configuration")
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Link: https://lore.kernel.org/r/20220412165055.257113-1-dossche.niels@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ec4cbf1cc ]
usb_get_dev() is called in stub_device_alloc(). When stub_probe() fails
after that, usb_put_dev() needs to be called to release the reference.
Fix this by moving usb_put_dev() to sdev_free error path handling.
Find this by code review.
Fixes: 3ff6744575 ("usbip: fix error handling in stub_probe()")
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220412020257.9767-1-hbh25y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58b7c85651 ]
Resource table is used by Linux to get information published by
remote processor. It should be not be used for memory allocation, so
not create rproc mem entry.
Fixes: b29b4249f8 ("remoteproc: imx_rproc: add i.MX specific parse fw hook")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220415025737.1561976-1-peng.fan@oss.nxp.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f398e0aa32 ]
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
aliases {
...
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
serial3 = &lpuart7;
}
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e0fd55719 ]
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference.
Fixes: 54da3e381c ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to set up register mapping")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220404143842.16960-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65a8b28702 ]
TTYs in ICANON mode have a special case that allows "pushing" a line
without a regular EOL character (like newline), by using EOF (the EOT
character - ASCII 0x4) as a pseudo-EOL. It is silently discarded, so
the reader of the PTS will receive the line *without* EOF or any other
terminating character.
This special case has an edge case: What happens if the readers buffer
is the same size as the line (without EOF)? Will they be able to tell
if the whole line is received, i.e. if the next read() will return more
of the same line or the next line?
There are two possibilities, that both have (dis)advantages:
1. The next read() returns 0. FreeBSD (13.0) and OSX (10.11) do this.
Advantage: The reader can interpret this as "the line is over".
Disadvantage: read() returning 0 means EOF, the reader could also
interpret it as "there's no more data" and stop reading or even
close the PT.
2. The next read() returns the next line, the EOF is silently discarded.
Solaris (or at least OpenIndiana 2021.10) does this, Linux has done
do this since commit 40d5e0905a ("n_tty: Fix EOF push handling");
this behavior was recently broken by commit 3593030761 ("tty:
n_tty: do not look ahead for EOL character past the end of the buffer").
Advantage: read() won't return 0 (EOF), reader less likely to be
confused (and things like `while(read(..)>0)` don't break)
Disadvantage: The reader can't really know if the read() continues
the last line (that filled the whole read buffer) or starts a
new line.
As both options are defensible (and are used by other Unix-likes), it's
best to stick to the "old" behavior since "n_tty: Fix EOF push handling"
of 2013, i.e. silently discard that EOF.
This patch - that I actually got from Linus for testing and only
modified slightly - restores that behavior by skipping an EOF
character if it's the next character after reading is done.
Based on a patch from Linus Torvalds.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611
Fixes: 3593030761 ("tty: n_tty: do not look ahead for EOL character past the end of the buffer")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Reviewed-and-tested-by: Daniel Gibson <daniel@gibson.sh>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Gibson <daniel@gibson.sh>
Link: https://lore.kernel.org/r/20220329235810.452513-2-daniel@gibson.sh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 507b05063d ]
In goldfish_tty_probe(), the port initialized through tty_port_init()
should be destroyed in error paths.In goldfish_tty_remove(), qtty->port
also should be destroyed or else might leak resources.
Fix the above by calling tty_port_destroy().
Fixes: 666b7793d4 ("goldfish: tty driver")
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Wang Weiyang <wangweiyang2@huawei.com>
Link: https://lore.kernel.org/r/20220328115844.86032-1-wangweiyang2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bfdbddd68 ]
When you don't select CONFIG_UBSAN_TRAP, you get:
# echo ARRAY_BOUNDS > /sys/kernel/debug/provoke-crash/DIRECT
[ 102.265827] ================================================================================
[ 102.278433] UBSAN: array-index-out-of-bounds in drivers/misc/lkdtm/bugs.c:342:16
[ 102.287207] index 8 is out of range for type 'char [8]'
[ 102.298722] ================================================================================
[ 102.313712] lkdtm: FAIL: survived array bounds overflow!
[ 102.318770] lkdtm: Unexpected! This kernel (5.16.0-rc1-s3k-dev-01884-g720dcf79314a ppc) was built with CONFIG_UBSAN_BOUNDS=y
It is not correct because when CONFIG_UBSAN_TRAP is not selected
you can't expect array bounds overflow to kill the thread.
Modify the logic so that when the kernel is built with
CONFIG_UBSAN_BOUNDS but without CONFIG_UBSAN_TRAP, you get a warning
about CONFIG_UBSAN_TRAP not been selected instead.
This also require a fix of pr_expected_config(), otherwise the
following error is encountered.
CC drivers/misc/lkdtm/bugs.o
drivers/misc/lkdtm/bugs.c: In function 'lkdtm_ARRAY_BOUNDS':
drivers/misc/lkdtm/bugs.c:351:2: error: 'else' without a previous 'if'
351 | else
| ^~~~
Fixes: c75be56e35 ("lkdtm/bugs: Add ARRAY_BOUNDS to selftests")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/363b58690e907c677252467a94fe49444c80ea76.1649704381.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a9800c81d ]
As the possible failure of the kmalloc(), the not_checked and checked
could be NULL pointer.
Therefore, it should be better to check it in order to avoid the
dereference of the NULL pointer.
Also, we need to kfree the 'not_checked' and 'checked' to avoid
the memory leak if fails.
And since it is just a test, it may directly return without error
number.
Fixes: ae2e1aad3e ("drivers/misc/lkdtm/bugs.c: add arithmetic overflow and array bounds checks")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220120092936.1874264-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe78ccf79b ]
The 24 bits data is stored in 32 bits in BE. There
is no need to shift it. This confuses user-space apps.
Fixes: b3af341bbd ("iio: adc: Add ad7124 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20220322105029.86389-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84ef256550 ]
If the list does not exit early then data == NULL and 'module' does not
point to a valid list element.
Using 'module' in such a case is not valid and was therefore removed.
Fixes: 6dd67645f2 ("greybus: audio: Use single codec driver registration")
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vaibhav Agarwal <vaibhav.sr@gmail.com>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20220321123626.3068639-1-jakobkoschel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3928cf0833 ]
When the MIPS_ALCHEMY board selection is MIPS_XXS1500 instead of
MIPS_DB1XXX, the PCMCIA driver 'db1xxx_ss' has build errors due
to missing DB1XXX symbols. The PCMCIA driver should be restricted
to MIPS_DB1XXX instead of MIPS_ALCHEMY to fix this build error.
ERROR: modpost: "bcsr_read" [drivers/pcmcia/db1xxx_ss.ko] undefined!
ERROR: modpost: "bcsr_mod" [drivers/pcmcia/db1xxx_ss.ko] undefined!
Fixes: 42a4f17dc3 ("MIPS: Alchemy: remove SOC_AU1X00 in favor of MIPS_ALCHEMY")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 22b106e535 upstream.
Commit d92c370a16 ("block: really clone the block cgroup in
bio_clone_blkg_association") changed bio_clone_blkg_association() to
just clone bio->bi_blkg reference from source to destination bio. This
is however wrong if the source and destination bios are against
different block devices because struct blkcg_gq is different for each
bdev-blkcg pair. This will result in IOs being accounted (and throttled
as a result) multiple times against the same device (src bdev) while
throttling of the other device (dst bdev) is ignored. In case of BFQ the
inconsistency can even result in crashes in bfq_bic_update_cgroup().
Fix the problem by looking up correct blkcg_gq for the cloned bio.
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Reported-and-tested-by: Donald Buczek <buczek@molgen.mpg.de>
Fixes: d92c370a16 ("block: really clone the block cgroup in bio_clone_blkg_association")
CC: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20220602081242.7731-1-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40f567bbb3 upstream.
The function kzalloc() in detached_dev_do_request() can fail, so its
return value should be checked.
Fixes: bc082a55d2 ("bcache: fix inaccurate io state for detached bcache devices")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20220527152818.27545-4-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42b805af10 upstream.
Now io_acct_set is alloc and free in personality. Remove the codes that
free io_acct_set in md_free and md_stop.
Fixes: 0c031fd37f (md: Move alloc/free acct bioset in to personality)
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f2571ad7a upstream.
In normal stop process, it does like this:
do_md_stop
|
__md_stop (pers->free(); mddev->private=NULL)
|
md_free (free mddev)
__md_stop sets mddev->private to NULL after pers->free. The raid device
will be stopped and mddev memory is free. But in reshape, it doesn't
free the mddev and mddev will still be used in new raid.
In reshape, it first sets mddev->private to new_pers and then runs
old_pers->free(). Now raid0 sets mddev->private to NULL in raid0_free.
The new raid can't work anymore. It will panic when dereference
mddev->private because of NULL pointer dereference.
It can panic like this:
[63010.814972] kernel BUG at drivers/md/raid10.c:928!
[63010.819778] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[63010.825011] CPU: 3 PID: 44437 Comm: md0_resync Kdump: loaded Not tainted 5.14.0-86.el9.x86_64 #1
[63010.833789] Hardware name: Dell Inc. PowerEdge R6415/07YXFK, BIOS 1.15.0 09/11/2020
[63010.841440] RIP: 0010:raise_barrier+0x161/0x170 [raid10]
[63010.865508] RSP: 0018:ffffc312408bbc10 EFLAGS: 00010246
[63010.870734] RAX: 0000000000000000 RBX: ffffa00bf7d39800 RCX: 0000000000000000
[63010.877866] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffa00bf7d39800
[63010.884999] RBP: 0000000000000000 R08: fffffa4945e74400 R09: 0000000000000000
[63010.892132] R10: ffffa00eed02f798 R11: 0000000000000000 R12: ffffa00bbc435200
[63010.899266] R13: ffffa00bf7d39800 R14: 0000000000000400 R15: 0000000000000003
[63010.906399] FS: 0000000000000000(0000) GS:ffffa00eed000000(0000) knlGS:0000000000000000
[63010.914485] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[63010.920229] CR2: 00007f5cfbe99828 CR3: 0000000105efe000 CR4: 00000000003506e0
[63010.927363] Call Trace:
[63010.929822] ? bio_reset+0xe/0x40
[63010.933144] ? raid10_alloc_init_r10buf+0x60/0xa0 [raid10]
[63010.938629] raid10_sync_request+0x756/0x1610 [raid10]
[63010.943770] md_do_sync.cold+0x3e4/0x94c
[63010.947698] md_thread+0xab/0x160
[63010.951024] ? md_write_inc+0x50/0x50
[63010.954688] kthread+0x149/0x170
[63010.957923] ? set_kthread_struct+0x40/0x40
[63010.962107] ret_from_fork+0x22/0x30
Removing the code that sets mddev->private to NULL in raid0 can fix
problem.
Fixes: 0c031fd37f (md: Move alloc/free acct bioset in to personality)
Reported-by: Fine Fan <ffan@redhat.com>
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f26967b9f7 upstream.
log_read_rst() returns ENOMEM error when there is not enough memory.
In this case, if info is returned without initialization,
it attempts to kfree the uninitialized info->r_page pointer. This patch
moves the memset initialization code to before log_read_rst() is called.
Reported-by: Gerald Lee <sundaywind2004@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a761d72fa upstream.
Make the two locations where exportfs helpers check permission to lookup
a given inode idmapped mount aware by switching it to the lookup_one()
helper. This is a bugfix for the open_by_handle_at() system call which
doesn't take idmapped mounts into account currently. It's not tied to a
specific commit so we'll just Cc stable.
In addition this is required to support idmapped base layers in overlay.
The overlay filesystem uses exportfs to encode and decode file handles
for its index=on mount option and when nfs_export=on.
Cc: <stable@vger.kernel.org>
Cc: <linux-fsdevel@vger.kernel.org>
Tested-by: Giuseppe Scrivano <gscrivan@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00675017e0 upstream.
Similar to the addition of lookup_one() add a version of
lookup_one_unlocked() and lookup_one_positive_unlocked() that take
idmapped mounts into account. This is required to port overlay to
support idmapped base layers.
Cc: <linux-fsdevel@vger.kernel.org>
Tested-by: Giuseppe Scrivano <gscrivan@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b95b668eaa upstream.
We're only adding BCMs to the commit list in aggregate(), but there are
cases where pre_aggregate() is called without subsequently calling
aggregate(). In particular, in icc_sync_state() when a node with initial
BW has zero requests. Since BCMs aren't added to the commit list in
these cases, we don't actually send the zero BW request to HW. So the
resources remain on unnecessarily.
Add BCMs to the commit list in pre_aggregate() instead, which is always
called even when there are no requests.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
[georgi: remove icc_sync_state for platforms with incomplete support]
Link: https://lore.kernel.org/r/20211125174751.25317-1-djakov@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f3724930e upstream.
The IPA BCM resource ("IP0") on sc7180 was moved to the clk-rpmh driver
in commit bcd63d222b ("clk: qcom: rpmh: Add IPA clock for SC7180") and
modeled as a clk, but this interconnect driver still had it modeled as
an interconnect. This was mostly OK because nobody used the interconnect
definition, until the interconnect framework started dropping bandwidth
requests on interconnects that aren't used via the sync_state callback
in commit 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state"). Once
that patch was applied the IP0 resource was going to be controlled from
two places, the clk framework and the interconnect framework.
Even then, things were probably going to be OK, because commit
b95b668eaa ("interconnect: qcom: icc-rpmh: Add BCMs to commit list in
pre_aggregate") was needed to actually drop bandwidth requests on unused
interconnects, of which the IPA was one of the interconnect that wasn't
getting dropped to zero. Combining the three commits together leads to
bad behavior where the interconnect framework is disabling the IP0
resource because it has no users while the clk framework thinks the IP0
resource is on because the only user, the IPA driver, has turned it on
via clk_prepare_enable(). Depending on when sync_state is called, we can
get into a situation like below:
IPA driver probes
IPA driver gets notified modem started
runtime PM get()
IPA clk enabled -> IP0 resource is ON
sync_state runs
interconnect zeroes out the IP0 resource -> IP0 resource is off
IPA driver tries to access a register and blows up
The crash is an unclocked access that manifest as an SError.
SError Interrupt on CPU0, code 0xbe000011 -- SError
CPU: 0 PID: 3595 Comm: mmdata_mgr Not tainted 5.17.1+ #166
Hardware name: Google Lazor (rev1 - 2) with LTE (DT)
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mutex_lock+0x4c/0x80
lr : mutex_lock+0x30/0x80
sp : ffffffc00da9b9c0
x29: ffffffc00da9b9c0 x28: 0000000000000000 x27: 0000000000000000
x26: ffffffc00da9bc90 x25: ffffff80c2024010 x24: ffffff80c2024000
x23: ffffff8083100000 x22: ffffff80831000d0 x21: ffffff80831000a8
x20: ffffff80831000a8 x19: ffffff8083100070 x18: 00000000ffff0a00
x17: 000000002f7254f1 x16: 0000000000000100 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 000000000001f0b8 x10: ffffffc00931f0b8 x9 : 0000000000000000
x8 : 0000000000000000 x7 : fefefefefeff2f60 x6 : 0000808080808080
x5 : 0000000000000000 x4 : 8080808080800000 x3 : ffffff80d2d4ee28
x2 : ffffff808c1d6e40 x1 : 0000000000000000 x0 : ffffff8083100070
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 0 PID: 3595 Comm: mmdata_mgr Not tainted 5.17.1+ #166
Hardware name: Google Lazor (rev1 - 2) with LTE (DT)
Call trace:
dump_backtrace+0xf4/0x114
show_stack+0x24/0x30
dump_stack_lvl+0x64/0x7c
dump_stack+0x18/0x38
panic+0x150/0x38c
nmi_panic+0x88/0xa0
arm64_serror_panic+0x74/0x80
do_serror+0x0/0x80
do_serror+0x58/0x80
el1h_64_error_handler+0x34/0x4c
el1h_64_error+0x78/0x7c
mutex_lock+0x4c/0x80
__gsi_channel_start+0x50/0x17c
gsi_channel_start+0x54/0x90
ipa_endpoint_enable_one+0x34/0xc0
ipa_open+0x4c/0x120
Remove all IP0 resource management from the interconnect driver so that
clk-rpmh is the sole owner. This fixes the issue by preventing the
interconnect driver from overwriting the IP0 resource data that the
clk-rpmh driver wrote.
Cc: Alex Elder <elder@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Cc: Mike Tipton <quic_mdtipton@quicinc.com>
Fixes: b95b668eaa ("interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate")
Fixes: bcd63d222b ("clk: qcom: rpmh: Add IPA clock for SC7180")
Fixes: 7d3b0b0d81 ("interconnect: qcom: Use icc_sync_state")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Alex Elder <elder@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220412220033.1273607-2-swboyd@chromium.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f41fdaea6 upstream.
Make the test_dummy_encryption mount option require that the encrypt
feature flag be already enabled on the filesystem, rather than
automatically enabling it. Practically, this means that "-O encrypt"
will need to be included in MKFS_OPTIONS when running xfstests with the
test_dummy_encryption mount option. (ext4/053 also needs an update.)
Moreover, as long as the preconditions for test_dummy_encryption are
being tightened anyway, take the opportunity to start rejecting it when
!CONFIG_FS_ENCRYPTION rather than ignoring it.
The motivation for requiring the encrypt feature flag is that:
- Having the filesystem auto-enable feature flags is problematic, as it
bypasses the usual sanity checks. The specific issue which came up
recently is that in kernel versions where ext4 supports casefold but
not encrypt+casefold (v5.1 through v5.10), the kernel will happily add
the encrypt flag to a filesystem that has the casefold flag, making it
unmountable -- but only for subsequent mounts, not the initial one.
This confused the casefold support detection in xfstests, causing
generic/556 to fail rather than be skipped.
- The xfstests-bld test runners (kvm-xfstests et al.) already use the
required mkfs flag, so they will not be affected by this change. Only
users of test_dummy_encryption alone will be affected. But, this
option has always been for testing only, so it should be fine to
require that the few users of this option update their test scripts.
- f2fs already requires it (for its equivalent feature flag).
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Link: https://lore.kernel.org/r/20220519204437.61645-1-ebiggers@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f44b3e74c3 upstream.
Remove unsupported forcing of `cpu_has_fpu' to 1, which makes the `nofpu'
kernel parameter non-functional, and also causes a link error:
ld: arch/mips/kernel/traps.o: in function `trap_init':
./arch/mips/include/asm/msa.h:(.init.text+0x348): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x354): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x360): undefined reference to `handle_fpe'
where the CONFIG_MIPS_FP_SUPPORT configuration option has been disabled.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Reported-by: Stephen Zhang <starzhangzsd@gmail.com>
Fixes: 7505576d1c ("MIPS: add support for SGI Octane (IP30)")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 424c3781dd upstream.
Remove unsupported forcing of `cpu_has_fpu' to 1, which makes the `nofpu'
kernel parameter non-functional, and also causes a link error:
ld: arch/mips/kernel/traps.o: in function `trap_init':
./arch/mips/include/asm/msa.h:(.init.text+0x348): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x354): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x360): undefined reference to `handle_fpe'
where the CONFIG_MIPS_FP_SUPPORT configuration option has been disabled.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Reported-by: Stephen Zhang <starzhangzsd@gmail.com>
Fixes: 0ebb2f4159 ("MIPS: IP27: Update/restructure CPU overrides")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f917af777 upstream.
Current rxe_requester() doesn't generate a completion when processing an
unsupported/invalid opcode. If rxe driver doesn't support a new opcode
(e.g. RDMA Atomic Write) and RDMA library supports it, an application
using the new opcode can reproduce this issue. Fix the issue by calling
"goto err;".
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20220410113513.27537-1-yangx.jy@fujitsu.com
Signed-off-by: Xiao Yang <yangx.jy@fujitsu.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db5dfbf5b2 upstream.
The bt number of cqc_timer of HIP09 increases compared with that of HIP08.
Therefore, cqc_timer_bt_num and num_cqc_timer do not match. As a result,
the driver may fail to allocate cqc_timer. So the driver needs to uniquely
uses cqc_timer_bt_num to represent the bt number of cqc_timer.
Fixes: 0e40dc2f70 ("RDMA/hns: Add timer allocation support for hip08")
Link: https://lore.kernel.org/r/20220429093545.58070-1-liangwenpeng@huawei.com
Signed-off-by: Yixing Liu <liuyixing1@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d0cc9e0e5 upstream.
These debugging tools let you call:
status = usb_control_msg_recv/send(udev, 0, REALTEK_USB_VENQT_CMD_REQ,
REALTEK_USB_VENQT_READ/WRITE, value,
REALTEK_USB_VENQT_CMD_IDX, io_buf,
size, RTW_USB_CONTROL_MSG_TIMEOUT,
GFP_KERNEL);
with a user controlled "value" in the 0-0xffff range. It's not a valid
API.
Fixes: 2b42bd58b3 ("staging: r8188eu: introduce new os_dep dir for RTL8188eu driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YoXS4OaD1oauPvmj@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts upstream commit f5bda35fba
from stable. It's not essential and will take some time during 5.19 to
work out properly.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
commit 37dc573c0a upstream.
list_is_head() was added recently[1], and didn't have a KUnit test. The
implementation is trivial, so it's not a particularly exciting test, but
it'd be nice to get back to full coverage of the list functions.
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/include/linux/list.h?id=0425473037db40d9e322631f2d4dc6ef51f97e88
Signed-off-by: David Gow <davidgow@google.com>
Acked-by: Daniel Latypov <dlatypov@google.com>
Acked-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 213adc63df upstream.
Commit 54de76c012 ("kselftest/cgroup: fix test_stress.sh to use OUTPUT
dir") changes the test_core command path from . to $OUTPUT. However,
variable OUTPUT may not be defined if the command is run interactively.
Fix that by using ${OUTPUT:-.} to cover both cases.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70132763d5 upstream.
Currently the (possibly compound) pages used for receive buffers are
freed using __free_pages(). But according to this comment above the
definition of that function, that's wrong:
If you want to use the page's reference count to decide
when to free the allocation, you should allocate a compound
page, and use put_page() instead of __free_pages().
Convert the call to __free_pages() in ipa_endpoint_replenish_one()
to use put_page() instead.
Fixes: 6a606b9015 ("net: ipa: allocate transaction in replenish loop")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 155c0c90bc upstream.
Currently the (possibly compound) page used for receive buffers are
freed using __free_pages(). But according to this comment above the
definition of that function, that's wrong:
If you want to use the page's reference count to decide when
to free the allocation, you should allocate a compound page,
and use put_page() instead of __free_pages().
Convert the call to __free_pages() in ipa_endpoint_trans_release()
to use put_page() instead.
Fixes: ed23f02680 ("net: ipa: define per-endpoint receive buffer size")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d2900f20e upstream.
Make sure to release the lane reset controller in case of a late probe
error (e.g. probe deferral).
Note that due to the reset controller being defined in devicetree in
"lane" child nodes, devm_reset_control_get_exclusive() cannot be used
directly.
Fixes: e78f3d15e1 ("phy: qcom-qmp: new qmp phy driver for qcom-chipsets")
Cc: stable@vger.kernel.org # 4.12
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220427063243.32576-3-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c1d3f79d9 upstream.
It is possibe that probe failure issue happens when the device
and its child_device's probe happens at the same time.
In coresight_make_links, has_conns_grp is true for parent, but
has_conns_grp is false for child device as has_conns_grp is set
to true in coresight_create_conns_sysfs_group. The probe of parent
device will fail at this condition. Add has_conns_grp check for
child device before make the links and make the process from
device_register to connection_create be atomic to avoid this
probe failure issue.
Cc: stable@vger.kernel.org
Suggested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Suggested-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>
Link: https://lore.kernel.org/r/20220309142206.15632-1-quic_jinlmao@quicinc.com
[ Added Cc stable ]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a177a36da upstream.
iolatency needs to track the number of inflight IOs per cgroup. As this
tracking can be expensive, it is disabled when no cgroup has iolatency
configured for the device. To ensure that the inflight counters stay
balanced, iolatency_set_limit() freezes the request_queue while manipulating
the enabled counter, which ensures that no IO is in flight and thus all
counters are zero.
Unfortunately, iolatency_set_limit() isn't the only place where the enabled
counter is manipulated. iolatency_pd_offline() can also dec the counter and
trigger disabling. As this disabling happens without freezing the q, this
can easily happen while some IOs are in flight and thus leak the counts.
This can be easily demonstrated by turning on iolatency on an one empty
cgroup while IOs are in flight in other cgroups and then removing the
cgroup. Note that iolatency shouldn't have been enabled elsewhere in the
system to ensure that removing the cgroup disables iolatency for the whole
device.
The following keeps flipping on and off iolatency on sda:
echo +io > /sys/fs/cgroup/cgroup.subtree_control
while true; do
mkdir -p /sys/fs/cgroup/test
echo '8:0 target=100000' > /sys/fs/cgroup/test/io.latency
sleep 1
rmdir /sys/fs/cgroup/test
sleep 1
done
and there's concurrent fio generating direct rand reads:
fio --name test --filename=/dev/sda --direct=1 --rw=randread \
--runtime=600 --time_based --iodepth=256 --numjobs=4 --bs=4k
while monitoring with the following drgn script:
while True:
for css in css_for_each_descendant_pre(prog['blkcg_root'].css.address_of_()):
for pos in hlist_for_each(container_of(css, 'struct blkcg', 'css').blkg_list):
blkg = container_of(pos, 'struct blkcg_gq', 'blkcg_node')
pd = blkg.pd[prog['blkcg_policy_iolatency'].plid]
if pd.value_() == 0:
continue
iolat = container_of(pd, 'struct iolatency_grp', 'pd')
inflight = iolat.rq_wait.inflight.counter.value_()
if inflight:
print(f'inflight={inflight} {disk_name(blkg.q.disk).decode("utf-8")} '
f'{cgroup_path(css.cgroup).decode("utf-8")}')
time.sleep(1)
The monitoring output looks like the following:
inflight=1 sda /user.slice
inflight=1 sda /user.slice
...
inflight=14 sda /user.slice
inflight=13 sda /user.slice
inflight=17 sda /user.slice
inflight=15 sda /user.slice
inflight=18 sda /user.slice
inflight=17 sda /user.slice
inflight=20 sda /user.slice
inflight=19 sda /user.slice <- fio stopped, inflight stuck at 19
inflight=19 sda /user.slice
inflight=19 sda /user.slice
If a cgroup with stuck inflight ends up getting throttled, the throttled IOs
will never get issued as there's no completion event to wake it up leading
to an indefinite hang.
This patch fixes the bug by unifying enable handling into a work item which
is automatically kicked off from iolatency_set_min_lat_nsec() which is
called from both iolatency_set_limit() and iolatency_pd_offline() paths.
Punting to a work item is necessary as iolatency_pd_offline() is called
under spinlocks while freezing a request_queue requires a sleepable context.
This also simplifies the code reducing LOC sans the comments and avoids the
unnecessary freezes which were happening whenever a cgroup's latency target
is newly set or cleared.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Liu Bo <bo.liu@linux.alibaba.com>
Fixes: 8c772a9bfc ("blk-iolatency: fix IO hang due to negative inflight counter")
Cc: stable@vger.kernel.org # v5.0+
Link: https://lore.kernel.org/r/Yn9ScX6Nx2qIiQQi@slm.duckdns.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2424369738 upstream.
Code must be resilient to enable a queue many times.
At the moment the queue is resetting so it's definitely not the expected
behavior.
v2: set vq->ready = 0 at disable.
Fixes: 2c53d0f64c ("vdpasim: vDPA device simulator")
Cc: stable@vger.kernel.org
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20220519145919.772896-1-eperezma@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a21c3ac93 upstream.
update documentation to correctly state the interrupt-cells to be 2.
Cc: stable@vger.kernel.org
Fixes: 4fd9bbc6e0 ("drivers/gpio: Altera soft IP GPIO driver devicetree binding")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 627f01eab9 upstream.
One of the changes in Sphinx 5.0.0 [1] says [sic]:
5.0.0 final
- #10474: language does not accept None as it value.
The default value of language becomes to 'en' now.
[1]: https://www.sphinx-doc.org/en/master/changes.html#release-5-0-0-released-may-30-2022
It results in a new warning from Sphinx 5.0.0 [sic]:
WARNING: Invalid configuration value found: 'language = None'.
Update your configuration to a valid langauge code. Falling
back to 'en' (English).
Silence the warning by using 'en'.
It works with all the Sphinx versions required for building
kernel documentation (1.7.9 or later).
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Link: https://lore.kernel.org/r/bd0c2ddc-2401-03cb-4526-79ca664e1cbe@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a55cf74ff upstream.
There is a race condition in smb2_compound_op:
after_close:
num_rqst++;
if (cfile) {
cifsFileInfo_put(cfile); // sends SMB2_CLOSE to the server
cfile = NULL;
This is triggered by smb2_query_path_info operation that happens during
revalidate_dentry. In smb2_query_path_info, get_readable_path is called to
load the cfile, increasing the reference counter. If in the meantime, this
reference becomes the very last, this call to cifsFileInfo_put(cfile) will
trigger a SMB2_CLOSE request sent to the server just before sending this compound
request – and so then the compound request fails either with EBADF/EIO depending
on the timing at the server, because the handle is already closed.
In the first scenario, the race seems to be happening between smb2_query_path_info
triggered by the rename operation, and between “cleanup” of asynchronous writes – while
fsync(fd) likely waits for the asynchronous writes to complete, releasing the writeback
structures can happen after the close(fd) call. So the EBADF/EIO errors will pop up if
the timing is such that:
1) There are still outstanding references after close(fd) in the writeback structures
2) smb2_query_path_info successfully fetches the cfile, increasing the refcounter by 1
3) All writeback structures release the same cfile, reducing refcounter to 1
4) smb2_compound_op is called with that cfile
In the second scenario, the race seems to be similar – here open triggers the
smb2_query_path_info operation, and if all other threads in the meantime decrease the
refcounter to 1 similarly to the first scenario, again SMB2_CLOSE will be sent to the
server just before issuing the compound request. This case is harder to reproduce.
See https://bugzilla.samba.org/show_bug.cgi?id=15051
Cc: stable@vger.kernel.org
Fixes: 8de9e86c67 ("cifs: create a helper to find a writeable handle by path name")
Signed-off-by: Ondrej Hubsch <ohubsch@purestorage.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2672a4bff6 upstream.
From inspection I found a couple of GPIO lookups that are
listed with device "gpio-pxa", but actually have a number
from a different gpio controller.
Try to rectify that here, with a guess of what the actual
device name is.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 096f585073 upstream.
Since commit 766c6b63aa ("spi: fix client driver breakages when using
GPIO descriptors"), the panel has been blank due to an inverted CS GPIO.
In order to correct this, drop the spi-cs-high from the panel SPI device.
Fixes: 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/CY4PR04MB05670C771062570E911AF3B4CB1C9@CY4PR04MB0567.namprd04.prod.outlook.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski
Uwe Kleine-König
Christophe JAILLET
Miaoqian Lin
Lin Ma
Niels Dossche
Hangyu Hua
Peng Fan
Sherry Sun
Daniel Gibson
Wang Weiyang
Christophe Leroy
Jiasheng Jiang
Alexandru Tachici
Jakob Koschel
Randy Dunlap
Greg Kroah-Hartman
Jan Kara
Caleb Connolly
Jia-Ju Bai
Xiao Ni
Namjae Jeon
Christian Brauner
Mike Tipton
Stephen Boyd
Eric Biggers
Maciej W. Rozycki
Xiao Yang
Yixing Liu
Dan Carpenter
Jason A. Donenfeld
David Gow
Waiman Long
Alex Elder
Johan Hovold
Mao Jinlong
Tejun Heo
Eugenio Pérez
Dinh Nguyen
Akira Yokosawa
Steve French
Arnd Bergmann
Jonathan Bakker