[ Upstream commit 2a5be6d134 ]
Correct the base address used during io write.
This bug had no impact over the overall functionality of the read and write
transactions. MLXBF_I2C_CAUSE_OR_CLEAR=0x18 so writing to (smbus->io + 0x18)
instead of (mst_cause->ioi + 0x18) actually writes to the sc_low_timeout
register which just sets the timeout value before a read/write aborts.
Fixes: b5b5b32081 (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 085aacaa73 ]
pm_runtime_get_sync() returning 1 also means the device is powered. So
resetting the chip registers in .remove() is possible and should be
done.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: d98bdd3a5b ("i2c: imx: Make sure to unregister adapter on remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0feea594e ]
Like Hillf Danton mentioned
syzbot should have been able to catch cancel_work_sync() in work context
by checking lockdep_map in __flush_work() for both flush and cancel.
in [1], being unable to report an obvious deadlock scenario shown below is
broken. From locking dependency perspective, sync version of cancel request
should behave as if flush request, for it waits for completion of work if
that work has already started execution.
----------
#include <linux/module.h>
#include <linux/sched.h>
static DEFINE_MUTEX(mutex);
static void work_fn(struct work_struct *work)
{
schedule_timeout_uninterruptible(HZ / 5);
mutex_lock(&mutex);
mutex_unlock(&mutex);
}
static DECLARE_WORK(work, work_fn);
static int __init test_init(void)
{
schedule_work(&work);
schedule_timeout_uninterruptible(HZ / 10);
mutex_lock(&mutex);
cancel_work_sync(&work);
mutex_unlock(&mutex);
return -EINVAL;
}
module_init(test_init);
MODULE_LICENSE("GPL");
----------
The check this patch restores was added by commit 0976dfc1d0
("workqueue: Catch more locking problems with flush_work()").
Then, lockdep's crossrelease feature was added by commit b09be676e0
("locking/lockdep: Implement the 'crossrelease' feature"). As a result,
this check was once removed by commit fd1a5b04df ("workqueue: Remove
now redundant lock acquisitions wrt. workqueue flushes").
But lockdep's crossrelease feature was removed by commit e966eaeeb6
("locking/lockdep: Remove the cross-release locking checks"). At this
point, this check should have been restored.
Then, commit d6e89786be ("workqueue: skip lockdep wq dependency in
cancel_work_sync()") introduced a boolean flag in order to distinguish
flush_work() and cancel_work_sync(), for checking "struct workqueue_struct"
dependency when called from cancel_work_sync() was causing false positives.
Then, commit 87915adc3f ("workqueue: re-add lockdep dependencies for
flushing") tried to restore "struct work_struct" dependency check, but by
error checked this boolean flag. Like an example shown above indicates,
"struct work_struct" dependency needs to be checked for both flush_work()
and cancel_work_sync().
Link: https://lkml.kernel.org/r/20220504044800.4966-1-hdanton@sina.com [1]
Reported-by: Hillf Danton <hdanton@sina.com>
Suggested-by: Lai Jiangshan <jiangshanlai@gmail.com>
Fixes: 87915adc3f ("workqueue: re-add lockdep dependencies for flushing")
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17d9c15c9b ]
I got an infinite loop and a WARNING report when executing a tail command
in virtiofs.
WARNING: CPU: 10 PID: 964 at fs/iomap/iter.c:34 iomap_iter+0x3a2/0x3d0
Modules linked in:
CPU: 10 PID: 964 Comm: tail Not tainted 5.19.0-rc7
Call Trace:
<TASK>
dax_iomap_rw+0xea/0x620
? __this_cpu_preempt_check+0x13/0x20
fuse_dax_read_iter+0x47/0x80
fuse_file_read_iter+0xae/0xd0
new_sync_read+0xfe/0x180
? 0xffffffff81000000
vfs_read+0x14d/0x1a0
ksys_read+0x6d/0xf0
__x64_sys_read+0x1a/0x20
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The tail command will call read() with a count of 0. In this case,
iomap_iter() will report this WARNING, and always return 1 which casuing
the infinite loop in dax_iomap_rw().
Fixing by checking count whether is 0 in dax_iomap_rw().
Fixes: ca289e0b95 ("fsdax: switch dax_iomap_rw to use iomap_iter")
Signed-off-by: Li Jinlin <lijinlin3@huawei.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20220725032050.3873372-1-lijinlin3@huawei.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0b9408f13 ]
The mode_valid field in drm_connector_helper_funcs is expected to be of
type:
enum drm_mode_status (* mode_valid) (struct drm_connector *connector,
struct drm_display_mode *mode);
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of cdn_dp_connector_mode_valid should be changed from
int to enum drm_mode_status.
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1703
Cc: llvm@lists.linux.dev
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220913205555.155149-1-nhuck@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41012d715d ]
This function consumes a lot of stack space and it blows up the size of
dml30_ModeSupportAndSystemConfigurationFull() with clang:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn30/display_mode_vba_30.c:3542:6: error: stack frame size (2200) exceeds limit (2048) in 'dml30_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
void dml30_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
^
1 error generated.
Commit a0f7e7f759 ("drm/amd/display: fix i386 frame size warning")
aimed to address this for i386 but it did not help x86_64.
To reduce the amount of stack space that
dml30_ModeSupportAndSystemConfigurationFull() uses, mark
UseMinimumDCFCLK() as noinline, using the _for_stack variant for
documentation. While this will increase the total amount of stack usage
between the two functions (1632 and 1304 bytes respectively), it will
make sure both stay below the limit of 2048 bytes for these files. The
aforementioned change does help reduce UseMinimumDCFCLK()'s stack usage
so it should not be reverted in favor of this change.
Link: https://github.com/ClangBuiltLinux/linux/issues/1681
Reported-by: "Sudip Mukherjee (Codethink)" <sudipm.mukherjee@gmail.com>
Tested-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21485d3da6 ]
Most of the arguments are identical between the two call sites and they
can be accessed through the 'struct vba_vars_st' pointer. This reduces
the total amount of stack space that
dml31_ModeSupportAndSystemConfigurationFull() uses by 112 bytes with
LLVM 16 (1976 -> 1864), helping clear up the following clang warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn31/display_mode_vba_31.c:3908:6: error: stack frame size (2216) exceeds limit (2048) in 'dml31_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
void dml31_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
^
1 error generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/1681
Reported-by: "Sudip Mukherjee (Codethink)" <sudipm.mukherjee@gmail.com>
Tested-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37934d4118 ]
Most of the arguments are identical between the two call sites and they
can be accessed through the 'struct vba_vars_st' pointer. This reduces
the total amount of stack space that
dml31_ModeSupportAndSystemConfigurationFull() uses by 240 bytes with
LLVM 16 (2216 -> 1976), helping clear up the following clang warning:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn31/display_mode_vba_31.c:3908:6: error: stack frame size (2216) exceeds limit (2048) in 'dml31_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
void dml31_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
^
1 error generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/1681
Reported-by: "Sudip Mukherjee (Codethink)" <sudipm.mukherjee@gmail.com>
Tested-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3601d620f2 ]
[Why]
For HDR mode, we get total 512 tf_point and after switching to SDR mode
we actually get 400 tf_point and the rest of points(401~512) still use
dirty value from HDR mode. We should limit the rest of the points to max
value.
[How]
Limit the value when coordinates_x.x > 1, just like what we do in
translate_from_linear_space for other re-gamma build paths.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Yao Wang1 <Yao.Wang1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66f99628eb ]
Currently, we aren't handling DRM_IOCTL_MODE_DIRTYFB. So, use
drm_atomic_helper_dirtyfb() as the dirty callback in the amdgpu_fb_funcs
struct.
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f0880e2cb7 ]
Passed through PCI device sometimes misbehave on Gen1 VMs when Hyper-V
DRM driver is also loaded. Looking at IOMEM assignment, we can see e.g.
$ cat /proc/iomem
...
f8000000-fffbffff : PCI Bus 0000:00
f8000000-fbffffff : 0000:00:08.0
f8000000-f8001fff : bb8c4f33-2ba2-4808-9f7f-02f3b4da22fe
...
fe0000000-fffffffff : PCI Bus 0000:00
fe0000000-fe07fffff : bb8c4f33-2ba2-4808-9f7f-02f3b4da22fe
fe0000000-fe07fffff : 2ba2:00:02.0
fe0000000-fe07fffff : mlx4_core
the interesting part is the 'f8000000' region as it is actually the
VM's framebuffer:
$ lspci -v
...
0000:00:08.0 VGA compatible controller: Microsoft Corporation Hyper-V virtual VGA (prog-if 00 [VGA controller])
Flags: bus master, fast devsel, latency 0, IRQ 11
Memory at f8000000 (32-bit, non-prefetchable) [size=64M]
...
hv_vmbus: registering driver hyperv_drm
hyperv_drm 5620e0c7-8062-4dce-aeb7-520c7ef76171: [drm] Synthvid Version major 3, minor 5
hyperv_drm 0000:00:08.0: vgaarb: deactivate vga console
hyperv_drm 0000:00:08.0: BAR 0: can't reserve [mem 0xf8000000-0xfbffffff]
hyperv_drm 5620e0c7-8062-4dce-aeb7-520c7ef76171: [drm] Cannot request framebuffer, boot fb still active?
Note: "Cannot request framebuffer" is not a fatal error in
hyperv_setup_gen1() as the code assumes there's some other framebuffer
device there but we actually have some other PCI device (mlx4 in this
case) config space there!
The problem appears to be that vmbus_allocate_mmio() can use dedicated
framebuffer region to serve any MMIO request from any device. The
semantics one might assume of a parameter named "fb_overlap_ok"
aren't implemented because !fb_overlap_ok essentially has no effect.
The existing semantics are really "prefer_fb_overlap". This patch
implements the expected and needed semantics, which is to not allocate
from the frame buffer space when !fb_overlap_ok.
Note, Gen2 VMs are usually unaffected by the issue because
framebuffer region is already taken by EFI fb (in case kernel supports
it) but Gen1 VMs may have this region unclaimed by the time Hyper-V PCI
pass-through driver tries allocating MMIO space if Hyper-V DRM/FB drivers
load after it. Devices can be brought up in any sequence so let's
resolve the issue by always ignoring 'fb_mmio' region for non-FB
requests, even if the region is unclaimed.
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20220827130345.1320254-4-vkuznets@redhat.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9a458402fb upstream.
[Why]
This fixes 892deb4826 ("drm/amdgpu: Separate vf2pf work item init from virt data exchange").
we should read pf2vf data based at mman.fw_vram_usage_va after gmc
sw_init. commit 892deb4826 breaks this logic.
[How]
calling amdgpu_virt_exchange_data in amdgpu_virt_init_data_exchange to
set the right base in the right sequence.
v2:
call amdgpu_virt_init_data_exchange after gmc sw_init to make data
exchange workqueue run
v3:
clean up the code logic
v4:
add some comment and make the code more readable
Fixes: 892deb4826 ("drm/amdgpu: Separate vf2pf work item init from virt data exchange")
Signed-off-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Reviewed-by: Horace Chen <horace.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db7ba07108 upstream.
Fix Oops in dasd_alias_get_start_dev() function caused by the pavgroup
pointer being NULL.
The pavgroup pointer is checked on the entrance of the function but
without the lcu->lock being held. Therefore there is a race window
between dasd_alias_get_start_dev() and _lcu_update() which sets
pavgroup to NULL with the lcu->lock held.
Fix by checking the pavgroup pointer with lcu->lock held.
Cc: <stable@vger.kernel.org> # 2.6.25+
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Link: https://lore.kernel.org/r/20220919154931.4123002-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e77cab77f2 upstream.
A very common pattern in the drivers is to advance xmit tail
index and do bookkeeping of Tx'ed characters. Create
uart_xmit_advance() to handle it.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220901143934.8850-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60f361722a upstream.
Since commit bd5305dcab ("tty: serial: fsl_lpuart: do software reset
for imx7ulp and imx8qxp"), certain i.MX UARTs are reset after they've
already been registered. Register state may thus be clobbered after
user space has begun to open and access the UART.
Avoid by performing the reset prior to registration.
Fixes: bd5305dcab ("tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp")
Cc: stable@vger.kernel.org # v5.15+
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/72fb646c1b0b11c989850c55f52f9ff343d1b2fa.1662884345.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68be1306ca ]
Consolidate rmap_recycle and rmap_add into a single function since they
are only ever called together (and only from one place). This has a nice
side effect of eliminating an extra kvm_vcpu_gfn_to_memslot(). In
addition it makes mmu_set_spte(), which is a very long function, a
little shorter.
No functional change intended.
Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20210813203504.2742757-3-dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: 604f533262 ("KVM: x86/mmu: add missing update to max_mmu_rmap_size")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83e4b19683 ]
RHEL/Fedora RPM build checks are stricter, and complain when executable
files don't have a shebang line, e.g.
*** WARNING: ./kselftests/net/forwarding/sch_red.sh is executable but has no shebang, removing executable bit
Fix it by adding shebang line.
Fixes: 6cf0291f95 ("selftests: forwarding: Add a RED test for SW datapath")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20220922024453.437757-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c31f26c8f6 ]
When reading the timestamp is required bnxt_tx_int() hands
over the ownership of the completed skb to the PTP worker.
The skb should not be used afterwards, as the worker may
run before the rest of our code and free the skb, leading
to a use-after-free.
Since dev_kfree_skb_any() accepts NULL make the loss of
ownership more obvious and set skb to NULL.
Fixes: 83bb623c96 ("bnxt_en: Transmit and retrieve packet timestamps")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220921201005.335390-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2e1cfefca ]
tfilter_put need to be called to put the refount got by tp->ops->get to
avoid possible refcount leak when chain->tmplt_ops != NULL and
chain->tmplt_ops != tp->ops.
Fixes: 7d5509fa0d ("net: sched: extend proto ops with 'put' callback")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Link: https://lore.kernel.org/r/20220921092734.31700-1-hbh25y@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 878e240571 ]
There is a separate receive path for small packets (under 256 bytes).
Instead of allocating a new dma-capable skb to be used for the next packet,
this path allocates a skb and copies the data into it (reusing the existing
sbk for the next packet). There are two bytes of junk data at the beginning
of every packet. I believe these are inserted in order to allow aligned DMA
and IP headers. We skip over them using skb_reserve. Before copying over
the data, we must use a barrier to ensure we see the whole packet. The
current code only synchronizes len bytes, starting from the beginning of
the packet, including the junk bytes. However, this leaves off the final
two bytes in the packet. Synchronize the whole packet.
To reproduce this problem, ping a HME with a payload size between 17 and
214
$ ping -s 17 <hme_address>
which will complain rather loudly about the data mismatch. Small packets
(below 60 bytes on the wire) do not have this issue. I suspect this is
related to the padding added to increase the minimum packet size.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220920235018.1675956-1-seanga2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e738455b2c ]
There might be a potential race between SMC-R buffer map and
link group termination.
smc_smcr_terminate_all() | smc_connect_rdma()
--------------------------------------------------------------
| smc_conn_create()
for links in smcibdev |
schedule links down |
| smc_buf_create()
| \- smcr_buf_map_usable_links()
| \- no usable links found,
| (rmb->mr = NULL)
|
| smc_clc_send_confirm()
| \- access conn->rmb_desc->mr[]->rkey
| (panic)
During reboot and IB device module remove, all links will be set
down and no usable links remain in link groups. In such situation
smcr_buf_map_usable_links() should return an error and stop the
CLC flow accessing to uninitialized mr.
Fixes: b9247544c1 ("net/smc: convert static link ID instances to support multiple links")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Link: https://lore.kernel.org/r/1663656189-32090-1-git-send-email-guwen@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90144dd8b0 ]
As the comment right before the mtk_dsi_stop() call advises,
mtk_dsi_stop() should only be called after
mtk_drm_crtc_atomic_disable(). That's because that function calls
drm_crtc_wait_one_vblank(), which requires the vblank irq to be enabled.
Previously mtk_dsi_stop(), being in mtk_dsi_poweroff() and guarded by a
refcount, would only be called at the end of
mtk_drm_crtc_atomic_disable(), through the call to mtk_crtc_ddp_hw_fini().
Commit cde7e2e35c ("drm/mediatek: Separate poweron/poweroff from
enable/disable and define new funcs") moved the mtk_dsi_stop() call to
mtk_output_dsi_disable(), causing it to be called before
mtk_drm_crtc_atomic_disable(), and consequently generating vblank
timeout warnings during suspend.
Move the mtk_dsi_stop() call back to mtk_dsi_poweroff() so that we have
a working vblank irq during mtk_drm_crtc_atomic_disable() and stop
getting vblank timeout warnings.
Fixes: cde7e2e35c ("drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Link: http://lists.infradead.org/pipermail/linux-mediatek/2022-August/046713.html
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 999e4eaa4b ]
It needs to enter the namespace before reading a file.
Fixes: 4183a8d70a ("perf tools: Allow synthesizing the build id for kernel/modules/tasks in PERF_RECORD_MMAP2")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20220920222822.2171056-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b427df27b ]
/proc/kallsyms and /proc/modules are compared before and after the copy
in order to ensure no changes during the copy.
However /proc/modules also might change due to reference counts changing
even though that does not make any difference.
Any modules loaded or unloaded should be visible in changes to kallsyms,
so it is not necessary to check /proc/modules also anyway.
Remove the comparison checking that /proc/modules is unchanged.
Fixes: fc1b691d76 ("perf buildid-cache: Add ability to add kcore to the cache")
Reported-by: Daniel Dao <dqminh@cloudflare.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Daniel Dao <dqminh@cloudflare.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220914122429.8770-1-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit babd04386b ]
The missing header makes it hard for programs like elfutils to open
these files.
Fixes: 2d86612aac ("perf symbol: Correct address for bss symbols")
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Lieven Hey <lieven.hey@kdab.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Link: https://lore.kernel.org/r/20220915092910.711036-1-lieven.hey@kdab.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d77326c33 ]
It seems the recent libbpf got more strict about the section name.
I'm seeing a failure like this:
$ sudo ./perf stat -a --bpf-counters --for-each-cgroup ^. sleep 1
libbpf: prog 'on_cgrp_switch': missing BPF prog type, check ELF section name 'perf_events'
libbpf: prog 'on_cgrp_switch': failed to load: -22
libbpf: failed to load object 'bperf_cgroup_bpf'
libbpf: failed to load BPF skeleton 'bperf_cgroup_bpf': -22
Failed to load cgroup skeleton
The section name should be 'perf_event' (without the trailing 's').
Although it's related to the libbpf change, it'd be better fix the
section name in the first place.
Fixes: 944138f048 ("perf stat: Enable BPF counter with --for-each-cgroup")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: bpf@vger.kernel.org
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/r/20220916184132.1161506-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5440428b3d ]
The dev->can.state is set to CAN_STATE_ERROR_ACTIVE, after the device
has been started. On busy networks the CAN controller might receive
CAN frame between and go into an error state before the dev->can.state
is assigned.
Assign dev->can.state before starting the controller to close the race
window.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220920195216.232481-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a1dbfefda ]
Since commit 744d23c71a ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 626 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xe4
As the Renesas SuperH Ethernet driver already calls phy_{stop,start}()
in its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/c6e1331b9bef61225fa4c09db3ba3e2e7214ba2d.1663598886.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4924c0cdce ]
Since commit 744d23c71a ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 1197 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xc8
As the Renesas Ethernet AVB driver already calls phy_{stop,start}() in
its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8ec796f47620980fdd0403e21bd8b7200b4fa1d4.1663598796.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62ce44c4ff ]
The bug fix was incomplete, it "replaced" crash with a memory leak.
The old code had an assignment to "ret" embedded into the conditional,
restore this.
Fixes: 7997eff828 ("netfilter: ebtables: reject blobs that don't provide all entry points")
Reported-and-tested-by: syzbot+a24c5252f3e3ab733464@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a4d6dd554 ]
It seems to me that percpu memory for chain stats started leaking since
commit 3bc158f8d0 ("netfilter: nf_tables: map basechain priority to
hardware priority") when nft_chain_offload_priority() returned an error.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 3bc158f8d0 ("netfilter: nf_tables: map basechain priority to hardware priority")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 921ebde3c0 ]
syzbot is reporting underflow of nft_counters_enabled counter at
nf_tables_addchain() [1], for commit 43eb8949cf ("netfilter:
nf_tables: do not leave chain stats enabled on error") missed that
nf_tables_chain_destroy() after nft_basechain_init() in the error path of
nf_tables_addchain() decrements the counter because nft_basechain_init()
makes nft_is_base_chain() return true by setting NFT_CHAIN_BASE flag.
Increment the counter immediately after returning from
nft_basechain_init().
Link: https://syzkaller.appspot.com/bug?extid=b5d82a651b71cd8a75ab [1]
Reported-by: syzbot <syzbot+b5d82a651b71cd8a75ab@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+b5d82a651b71cd8a75ab@syzkaller.appspotmail.com>
Fixes: 43eb8949cf ("netfilter: nf_tables: do not leave chain stats enabled on error")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1461d212ab ]
taprio can only operate as root qdisc, and to that end, there exists the
following check in taprio_init(), just as in mqprio:
if (sch->parent != TC_H_ROOT)
return -EOPNOTSUPP;
And indeed, when we try to attach taprio to an mqprio child, it fails as
expected:
$ tc qdisc add dev swp0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
$ tc qdisc replace dev swp0 parent 1:2 taprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 sched-entry S 0x7f 990000 sched-entry S 0x80 100000 \
flags 0x0 clockid CLOCK_TAI
Error: sch_taprio: Can only be attached as root qdisc.
(extack message added by me)
But when we try to attach a taprio child to a taprio root qdisc,
surprisingly it doesn't fail:
$ tc qdisc replace dev swp0 root handle 1: taprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 sched-entry S 0x7f 990000 sched-entry S 0x80 100000 \
flags 0x0 clockid CLOCK_TAI
$ tc qdisc replace dev swp0 parent 1:2 taprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 sched-entry S 0x7f 990000 sched-entry S 0x80 100000 \
flags 0x0 clockid CLOCK_TAI
This is because tc_modify_qdisc() behaves differently when mqprio is
root, vs when taprio is root.
In the mqprio case, it finds the parent qdisc through
p = qdisc_lookup(dev, TC_H_MAJ(clid)), and then the child qdisc through
q = qdisc_leaf(p, clid). This leaf qdisc q has handle 0, so it is
ignored according to the comment right below ("It may be default qdisc,
ignore it"). As a result, tc_modify_qdisc() goes through the
qdisc_create() code path, and this gives taprio_init() a chance to check
for sch_parent != TC_H_ROOT and error out.
Whereas in the taprio case, the returned q = qdisc_leaf(p, clid) is
different. It is not the default qdisc created for each netdev queue
(both taprio and mqprio call qdisc_create_dflt() and keep them in
a private q->qdiscs[], or priv->qdiscs[], respectively). Instead, taprio
makes qdisc_leaf() return the _root_ qdisc, aka itself.
When taprio does that, tc_modify_qdisc() goes through the qdisc_change()
code path, because the qdisc layer never finds out about the child qdisc
of the root. And through the ->change() ops, taprio has no reason to
check whether its parent is root or not, just through ->init(), which is
not called.
The problem is the taprio_leaf() implementation. Even though code wise,
it does the exact same thing as mqprio_leaf() which it is copied from,
it works with different input data. This is because mqprio does not
attach itself (the root) to each device TX queue, but one of the default
qdiscs from its private array.
In fact, since commit 13511704f8 ("net: taprio offload: enforce qdisc
to netdev queue mapping"), taprio does this too, but just for the full
offload case. So if we tried to attach a taprio child to a fully
offloaded taprio root qdisc, it would properly fail too; just not to a
software root taprio.
To fix the problem, stop looking at the Qdisc that's attached to the TX
queue, and instead, always return the default qdiscs that we've
allocated (and to which we privately enqueue and dequeue, in software
scheduling mode).
Since Qdisc_class_ops :: leaf is only called from tc_modify_qdisc(),
the risk of unforeseen side effects introduced by this change is
minimal.
Fixes: 5a781ccbd1 ("tc: Add support for configuring the taprio scheduler")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db46e3a88a ]
In an incredibly strange API design decision, qdisc->destroy() gets
called even if qdisc->init() never succeeded, not exclusively since
commit 87b60cfacf ("net_sched: fix error recovery at qdisc creation"),
but apparently also earlier (in the case of qdisc_create_dflt()).
The taprio qdisc does not fully acknowledge this when it attempts full
offload, because it starts off with q->flags = TAPRIO_FLAGS_INVALID in
taprio_init(), then it replaces q->flags with TCA_TAPRIO_ATTR_FLAGS
parsed from netlink (in taprio_change(), tail called from taprio_init()).
But in taprio_destroy(), we call taprio_disable_offload(), and this
determines what to do based on FULL_OFFLOAD_IS_ENABLED(q->flags).
But looking at the implementation of FULL_OFFLOAD_IS_ENABLED()
(a bitwise check of bit 1 in q->flags), it is invalid to call this macro
on q->flags when it contains TAPRIO_FLAGS_INVALID, because that is set
to U32_MAX, and therefore FULL_OFFLOAD_IS_ENABLED() will return true on
an invalid set of flags.
As a result, it is possible to crash the kernel if user space forces an
error between setting q->flags = TAPRIO_FLAGS_INVALID, and the calling
of taprio_enable_offload(). This is because drivers do not expect the
offload to be disabled when it was never enabled.
The error that we force here is to attach taprio as a non-root qdisc,
but instead as child of an mqprio root qdisc:
$ tc qdisc add dev swp0 root handle 1: \
mqprio num_tc 8 map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
$ tc qdisc replace dev swp0 parent 1:1 \
taprio num_tc 8 map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 base-time 0 \
sched-entry S 0x7f 990000 sched-entry S 0x80 100000 \
flags 0x0 clockid CLOCK_TAI
Unable to handle kernel paging request at virtual address fffffffffffffff8
[fffffffffffffff8] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Call trace:
taprio_dump+0x27c/0x310
vsc9959_port_setup_tc+0x1f4/0x460
felix_port_setup_tc+0x24/0x3c
dsa_slave_setup_tc+0x54/0x27c
taprio_disable_offload.isra.0+0x58/0xe0
taprio_destroy+0x80/0x104
qdisc_create+0x240/0x470
tc_modify_qdisc+0x1fc/0x6b0
rtnetlink_rcv_msg+0x12c/0x390
netlink_rcv_skb+0x5c/0x130
rtnetlink_rcv+0x1c/0x2c
Fix this by keeping track of the operations we made, and undo the
offload only if we actually did it.
I've added "bool offloaded" inside a 4 byte hole between "int clockid"
and "atomic64_t picos_per_byte". Now the first cache line looks like
below:
$ pahole -C taprio_sched net/sched/sch_taprio.o
struct taprio_sched {
struct Qdisc * * qdiscs; /* 0 8 */
struct Qdisc * root; /* 8 8 */
u32 flags; /* 16 4 */
enum tk_offsets tk_offset; /* 20 4 */
int clockid; /* 24 4 */
bool offloaded; /* 28 1 */
/* XXX 3 bytes hole, try to pack */
atomic64_t picos_per_byte; /* 32 0 */
/* XXX 8 bytes hole, try to pack */
spinlock_t current_entry_lock; /* 40 0 */
/* XXX 8 bytes hole, try to pack */
struct sched_entry * current_entry; /* 48 8 */
struct sched_gate_list * oper_sched; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
Fixes: 9c66d15646 ("taprio: Add support for hardware offloading")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5641c751fe ]
TSN features on the ENETC (taprio, cbs, gate, police) are configured
through a mix of command BD ring messages and port registers:
enetc_port_rd(), enetc_port_wr().
Port registers are a region of the ENETC memory map which are only
accessible from the PCIe Physical Function. They are not accessible from
the Virtual Functions.
Moreover, attempting to access these registers crashes the kernel:
$ echo 1 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs
pci 0000:00:01.0: [1957:ef00] type 00 class 0x020001
fsl_enetc_vf 0000:00:01.0: Adding to iommu group 15
fsl_enetc_vf 0000:00:01.0: enabling device (0000 -> 0002)
fsl_enetc_vf 0000:00:01.0 eno0vf0: renamed from eth0
$ tc qdisc replace dev eno0vf0 root taprio num_tc 8 map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 base-time 0 \
sched-entry S 0x7f 900000 sched-entry S 0x80 100000 flags 0x2
Unable to handle kernel paging request at virtual address ffff800009551a08
Internal error: Oops: 96000007 [#1] PREEMPT SMP
pc : enetc_setup_tc_taprio+0x170/0x47c
lr : enetc_setup_tc_taprio+0x16c/0x47c
Call trace:
enetc_setup_tc_taprio+0x170/0x47c
enetc_setup_tc+0x38/0x2dc
taprio_change+0x43c/0x970
taprio_init+0x188/0x1e0
qdisc_create+0x114/0x470
tc_modify_qdisc+0x1fc/0x6c0
rtnetlink_rcv_msg+0x12c/0x390
Split enetc_setup_tc() into separate functions for the PF and for the
VF drivers. Also remove enetc_qos.o from being included into
enetc-vf.ko, since it serves absolutely no purpose there.
Fixes: 34c6adf197 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220916133209.3351399-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fed38e64d9 ]
The VF netdev driver shouldn't respond to changes in the NETIF_F_HW_TC
flag; only PFs should. Moreover, TSN-specific code should go to
enetc_qos.c, which should not be included in the VF driver.
Fixes: 79e499829f ("net: enetc: add hw tc hw offload features for PSPF capability")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220916133209.3351399-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26c013108c ]
Doing a variable-sized memcpy is slower, and the compiler isn't smart
enough to turn this into a constant-size assignment.
Further, Kees' latest fortified memcpy will actually bark, because the
destination pointer is type sockaddr, not explicitly sockaddr_in or
sockaddr_in6, so it thinks there's an overflow:
memcpy: detected field-spanning write (size 28) of single field
"&endpoint.addr" at drivers/net/wireguard/netlink.c:446 (size 16)
Fix this by just assigning by using explicit casts for each checked
case.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reported-by: syzbot+a448cda4dba2dac50de5@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 684dec3cf4 ]
A previous commit tried to make the ratelimiter timings test more
reliable but in the process made it less reliable on other
configurations. This is an impossible problem to solve without
increasingly ridiculous heuristics. And it's not even a problem that
actually needs to be solved in any comprehensive way, since this is only
ever used during development. So just cordon this off with a DEBUG_
ifdef, just like we do for the trie's randomized tests, so it can be
enabled while hacking on the code, and otherwise disabled in CI. In the
process we also revert 151c8e499f.
Fixes: 151c8e499f ("wireguard: ratelimiter: use hrtimer in selftest")
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf412ec333 ]
IPA can route packets between IPA-connected entities. The AP and
modem are currently the only such entities supported, and no routing
is required to transfer packets between them.
The number of entries in each routing table is fixed, and defined at
initialization time. Some of these entries are designated for use
by the modem, and the rest are available for the AP to use. The AP
sends a QMI message to the modem which describes (among other
things) information about routing table memory available for the
modem to use.
Currently the QMI initialization packet gives wrong information in
its description of routing tables. What *should* be supplied is the
maximum index that the modem can use for the routing table memory
located at a given location. The current code instead supplies the
total *number* of routing table entries. Furthermore, the modem is
granted the entire table, not just the subset it's supposed to use.
This patch fixes this. First, the ipa_mem_bounds structure is
generalized so its "end" field can be interpreted either as a final
byte offset, or a final array index. Second, the IPv4 and IPv6
(non-hashed and hashed) table information fields in the QMI
ipa_init_modem_driver_req structure are changed to be ipa_mem_bounds
rather than ipa_mem_array structures. Third, we set the "end" value
for each routing table to be the last index, rather than setting the
"count" to be the number of indices. Finally, instead of allowing
the modem to use all of a routing table's memory, it is limited to
just the portion meant to be used by the modem. In all versions of
IPA currently supported, that is IPA_ROUTE_MODEM_COUNT (8) entries.
Update a few comments for clarity.
Fixes: 530f9216a9 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20220913204602.1803004-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c48709e6d ]
In of_mdiobus_register(), we should call of_node_put() for 'child'
escaped out of for_each_available_child_of_node().
Fixes: 66bdede495 ("of_mdio: Fix broken PHY IRQ in case of probe deferral")
Co-developed-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220913125659.3331969-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8a79c0305 ]
The Kconfig symbol depended on MMU but was dropped by the commit
acad3fe650 ("drm/hisilicon: Removed the dependency on the mmu")
because it already had as a dependency ARM64 that already selects MMU.
But later, commit a0f25a6bb3 ("drm/hisilicon/hibmc: Allow to be built
if COMPILE_TEST is enabled") allowed the driver to be built for non-ARM64
when COMPILE_TEST is set but that could lead to unmet direct dependencies
and linking errors.
Prevent a kconfig warning when MMU is not enabled by making
DRM_HISI_HIBMC depend on MMU.
WARNING: unmet direct dependencies detected for DRM_TTM
Depends on [n]: HAS_IOMEM [=y] && DRM [=m] && MMU [=n]
Selected by [m]:
- DRM_TTM_HELPER [=m] && HAS_IOMEM [=y] && DRM [=m]
- DRM_HISI_HIBMC [=m] && HAS_IOMEM [=y] && DRM [=m] && PCI [=y] && (ARM64 || COMPILE_TEST [=y])
Fixes: acad3fe650 ("drm/hisilicon: Removed the dependency on the mmu")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Xinliang Liu <xinliang.liu@linaro.org>
Cc: Tian Tao <tiantao6@hisilicon.com>
Cc: John Stultz <jstultz@google.com>
Cc: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Cc: Chen Feng <puck.chen@hisilicon.com>
Cc: Christian Koenig <christian.koenig@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531025557.29593-1-rdunlap@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0f25a6bb3 ]
The commit feeb07d0ca ("drm/hisilicon/hibmc: Make CONFIG_DRM_HISI_HIBMC
depend on ARM64") made the driver Kconfig symbol to depend on ARM64 since
it only supports that architecture and loading the module on others would
lead to incorrect video modes being used.
But it also prevented the driver to be built on other architectures which
is useful to have compile test coverage when doing subsystem wide changes.
Make the dependency instead to be (ARM64 || COMPILE_TEST), so the driver
is buildable when the CONFIG_COMPILE_TEST option is enabled.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211216210936.3329977-1-javierm@redhat.com
Stable-dep-of: d8a79c0305 ("drm/hisilicon: Add depends on MMU")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a242eb291 ]
Trying to get the channel from the tx_queue variable here is wrong
because we can only be here if tx_queue is NULL, so we shouldn't
dereference it. As the above comment in the code says, this is very
unlikely to happen, but it's wrong anyway so let's fix it.
I hit this issue because of a different bug that caused tx_queue to be
NULL. If that happens, this is the error message that we get here:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[...]
RIP: 0010:efx_hard_start_xmit+0x153/0x170 [sfc]
Fixes: 12804793b1 ("sfc: decouple TXQ type from label")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220914111135.21038-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f232af4295 ]
In legacy interrupt mode the tx_channel_offset was hardcoded to 1, but
that's not correct if efx_sepparate_tx_channels is false. In that case,
the offset is 0 because the tx queues are in the single existing channel
at index 0, together with the rx queue.
Without this fix, as soon as you try to send any traffic, it tries to
get the tx queues from an uninitialized channel getting these errors:
WARNING: CPU: 1 PID: 0 at drivers/net/ethernet/sfc/tx.c:540 efx_hard_start_xmit+0x12e/0x170 [sfc]
[...]
RIP: 0010:efx_hard_start_xmit+0x12e/0x170 [sfc]
[...]
Call Trace:
<IRQ>
dev_hard_start_xmit+0xd7/0x230
sch_direct_xmit+0x9f/0x360
__dev_queue_xmit+0x890/0xa40
[...]
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[...]
RIP: 0010:efx_hard_start_xmit+0x153/0x170 [sfc]
[...]
Call Trace:
<IRQ>
dev_hard_start_xmit+0xd7/0x230
sch_direct_xmit+0x9f/0x360
__dev_queue_xmit+0x890/0xa40
[...]
Fixes: c308dfd1b4 ("sfc: fix wrong tx channel offset with efx_separate_tx_channels")
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20220914103648.16902-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 198eb7e1b8 ]
While converting max_tx_rate from bytes to Mbps, this value was set to 0,
if the original value was lower than 125000 bytes (1 Mbps). This would
cause no transmission rate limiting to occur. This happened due to lack of
check of max_tx_rate against the 1 Mbps value for max_tx_rate and the
following division by 125000. Fix this issue by adding a helper
i40e_bw_bytes_to_mbits() which sets max_tx_rate to minimum usable value of
50 Mbps, if its value is less than 1 Mbps, otherwise do the required
conversion by dividing by 125000.
Fixes: 5ecae4120a ("i40e: Refactor VF BW rate limiting")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Asmaa Mnebhi
Uwe Kleine-König
Tetsuo Handa
Li Jinlin
Nathan Huckleberry
Nathan Chancellor
Yao Wang1
Hamza Mahfooz
Guchun Chen
Hans de Goede
Vitaly Kuznetsov
Jingwen Chen
Stefan Haberland
Ilpo Järvinen
Lukas Wunner
David Matlack
Hangbin Liu
Jakub Kicinski
Hangyu Hua
Sean Anderson
Jonathan Toppins
Wen Gu
Nícolas F. R. A. Prado
Namhyung Kim
Adrian Hunter
Lieven Hey
Marc Kleine-Budde
Geert Uytterhoeven
Florian Westphal
Vladimir Oltean
Jason A. Donenfeld
Alex Elder
Liang He
Randy Dunlap
Javier Martinez Canillas
Íñigo Huguet
Michal Jaron