- Add some trace points for clk_set_rate() "range" functions
- DVFS support for AT91 clk driver
* clk-ti:
clk: ti: omap5: Fix reboot DPLL lock failure when using ABE TIMERs
clk: ti: Fix memleak in ti_fapll_synth_setup
* clk-analog:
clk: axi-clkgen: move the OF table at the bottom of the file
clk: axi-clkgen: wrap limits in a struct and keep copy on the state object
dt-bindings: clock: adi,axi-clkgen: convert old binding to yaml format
* clk-trace:
clk: Trace clk_set_rate() "range" functions
* clk-at91:
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
* clk-silabs:
clk: si5351: Wait for bit clear after PLL reset
- Support for SiFive FU740 PRCI
- Add hardware enable information to clk_summary debugfs
* clk-tegra:
clk: tegra: Fix duplicated SE clock entry
clk: tegra: bpmp: Clamp clock rates on requests
clk: tegra: Do not return 0 on failure
* clk-imx: (24 commits)
clk: imx: scu: remove the calling of device_is_bound
clk: imx: scu: Make pd_np with static keyword
clk: imx8mq: drop of_match_ptr from of_device_id table
clk: imx8mp: drop of_match_ptr from of_device_id table
clk: imx8mn: drop of_match_ptr from of_device_id table
clk: imx8mm: drop of_match_ptr from of_device_id table
clk: imx: gate2: Remove unused variable ret
clk: imx: gate2: Add locking in is_enabled op
clk: imx: gate2: Add cgr_mask for more flexible number of control bits
clk: imx: gate2: Check if clock is enabled against cgr_val
clk: imx: gate2: Keep the register writing in on place
clk: imx: gate2: Remove the IMX_CLK_GATE2_SINGLE_BIT special case
clk: imx: scu: fix build break when compiled as modules
clk: imx: remove redundant assignment to pointer np
clk: imx: remove unneeded semicolon
clk: imx: lpcg: add suspend/resume support
clk: imx: clk-imx8qxp-lpcg: add runtime pm support
clk: imx: lpcg: allow lpcg clk to take device pointer
clk: imx: imx8qxp-lpcg: add parsing clocks from device tree
clk: imx: scu: add suspend/resume support
...
* clk-sifive:
clk: sifive: Add clock enable and disable ops
clk: sifive: Fix the wrong bit field shift
clk: sifive: Add a driver for the SiFive FU740 PRCI IP block
clk: sifive: Use common name for prci configuration
clk: sifive: Extract prci core to common base
dt-bindings: fu740: prci: add YAML documentation for the FU740 PRCI
* clk-mediatek:
clk: mediatek: Make mtk_clk_register_mux() a static function
* clk-summary:
clk: Add hardware-enable column to clk summary
Document the device tree bindings of the Canaan Kendryte K210 SoC clock
driver in Documentation/devicetree/bindings/clock/canaan,k210-clk.yaml.
The header file include/dt-bindings/clock/k210-clk.h is modified to
include the complete list of IDs for all clocks of the SoC.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201220085725.19545-3-damien.lemoal@wdc.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Register CPU clock as being the master clock prescaler. This would
be used by DVFS. The block schema of SAMA7G5's PMC contains also a divider
between master clock prescaler and CPU (PMC_CPU_RATIO.RATIO) but the
frequencies supported by SAMA7G5 could be directly received from
CPUPLL + master clock prescaler and the extra divider would do no work in
case it would be enabled.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-12-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add SAMA7G5 specific PLL defines to be referenced in a phandle as a
PMC_TYPE_CORE clock.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea@microchip.com: adapt comit message, adapt sama7g5.c]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1605800597-16720-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Core changes:
- Retired the old set-up function for GPIO IRQ chips. All chips
now use the template struct gpio_irq_chip and pass that to the core
to be set up alongside the gpio_chip. We can finally get rid of
the old cruft.
- Some refactoring and clean up of the core code.
- Support edge event timestamps to be stamped using REALTIME
(wall clock) timestamps. We have found solid use cases for
this, so we support it.
New drivers:
- MStar MSC313 GPIO driver.
- HiSilicon GPIO driver.
Driver improvements:
- The PCA953x driver now also supports the NXP PCAL9554B/C chips.
- The mockup driver can now be probed from the device tree which
is pretty useful for virtual prototyping of devices.
- The Rcar driver now supports .get_multiple()
- The MXC driver dropped some legacy and became a pure device
tree client.
- The Exar driver was moved over to the IDA interface for
enumerating, and also switched over to using regmap for
register access.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElDRnuGcz/wPCXQWMQRCzN7AZXXMFAl/b0r0ACgkQQRCzN7AZ
XXPRIQ/+P2VxypIIi8o5ZJLt/UN1CPGbh10WCl9yR95pM7Ekxocsa05MMAyPCbCA
SzDSo4wfrbVLd+C8oqGyLcyxR4A8LQDoc/MaBUC60SDr/BY2eu6bRCs9UttWUPUN
59H0r/dMAcSpIXwB9A7dKmF7Ps1Lz9naeZiGV8vw8hmuN4h3RtsWd10h8WDhByoq
RA099lNKs6pFpx61hvn+6mr8ewkm6RFh9q9/eg+zU0gVeaXpYLO6zHTnRS3dARIg
9qLZ54mRUAeybpUCi+CpleUM7qQI8wYHB7pJutAXByWVACie91P5youJv2JvMgs3
rvYyjRkHkM+EtpyXStv5zzfIi0JF746zWeeQmrR3bYy7prnIjjkUgIZb2Jmqu0p2
R0PAOmylociuSsEpARIqlGebqMKlmpsekuhJsf8x53le3nM4B2qC6fVEXFfYrp2L
sTfxeejmIFBBLLSSbfBFQOk3La9YBURGsidqgA2lQXL1ZSVhV6UrfblyLET6cOgs
y4ORYCV4SxeErUhePkA0GXjnu00nC9iD2Too6sTF+oRIirXX3R4SBbgoHKBEhMNe
/CWjYduwg7SkqwdeaBpZNU9jpFqq8Rny6nid13FMFORJWAszECzxcBIUaN55S/98
Z8QD0DJNo9nJZdtwT7OYE+x7/QcxgIHClU5MsrXS4yf3SlZHbAk=
=nrFU
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.11 kernel cycle:
Core changes:
- Retired the old set-up function for GPIO IRQ chips. All chips now
use the template struct gpio_irq_chip and pass that to the core to
be set up alongside the gpio_chip. We can finally get rid of the
old cruft.
- Some refactoring and clean up of the core code.
- Support edge event timestamps to be stamped using REALTIME (wall
clock) timestamps. We have found solid use cases for this, so we
support it.
New drivers:
- MStar MSC313 GPIO driver.
- HiSilicon GPIO driver.
Driver improvements:
- The PCA953x driver now also supports the NXP PCAL9554B/C chips.
- The mockup driver can now be probed from the device tree which is
pretty useful for virtual prototyping of devices.
- The Rcar driver now supports .get_multiple()
- The MXC driver dropped some legacy and became a pure device tree
client.
- The Exar driver was moved over to the IDA interface for
enumerating, and also switched over to using regmap for register
access"
* tag 'gpio-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
MAINTAINERS: Remove reference to non-existing file
gpio: hisi: Do not require ACPI for COMPILE_TEST
MAINTAINERS: Add maintainer for HiSilicon GPIO driver
gpio: gpio-hisi: Add HiSilicon GPIO support
gpio: cs5535: Simplify the return expression of cs5535_gpio_probe()
gpiolib: irq hooks: fix recursion in gpiochip_irq_unmask
dt-bindings: mt7621-gpio: convert bindings to YAML format
gpiolib: cdev: Flag invalid GPIOs as used
gpio: put virtual gpio device into their own submenu
drivers: gpio: amd8111: use SPDX-License-Identifier
drivers: gpio: amd8111: prefer dev_err()/dev_info() over raw printk
drivers: gpio: bt8xx: prefer dev_err()/dev_warn() over of raw printk
gpio: Add TODO item for debugfs interface
gpio: just plain warning when nonexisting gpio requested
tools: gpio: add option to report wall-clock time to gpio-event-mon
tools: gpio: add support for reporting realtime event clock to lsgpio
gpiolib: cdev: allow edge event timestamps to be configured as REALTIME
gpio: msc313: MStar MSC313 GPIO driver
dt-bindings: gpio: Binding for MStar MSC313 GPIO controller
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
...
New drivers/devices
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
- Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI keystone drivers for 5.11 included here due to dependency for TI
drivers
-----BEGIN PGP SIGNATURE-----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=uNBn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"The last dmaengine updates for this year :)
This contains couple of new drivers, new device support and updates to
bunch of drivers.
New drivers/devices:
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI drivers"
* tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (75 commits)
soc: ti: k3-ringacc: Use correct error casting in k3_ringacc_dmarings_init
dmaengine: ti: k3-udma-glue: Add support for K3 PKTDMA
dmaengine: ti: k3-udma: Initial support for K3 PKTDMA
dmaengine: ti: k3-udma: Add support for BCDMA channel TPL handling
dmaengine: ti: k3-udma: Initial support for K3 BCDMA
soc: ti: k3-ringacc: add AM64 DMA rings support.
dmaengine: ti: Add support for k3 event routers
dmaengine: ti: k3-psil: Add initial map for AM64
dmaengine: ti: k3-psil: Extend psil_endpoint_config for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 BCDMA
dmaengine: dmatest: Use dmaengine_get_dma_device
dmaengine: doc: client: Update for dmaengine_get_dma_device() usage
dmaengine: Add support for per channel coherency handling
dmaengine: of-dma: Add support for optional router configuration callback
dmaengine: ti: k3-udma-glue: Configure the dma_dev for rings
dmaengine: ti: k3-udma-glue: Get the ringacc from udma_dev
dmaengine: ti: k3-udma-glue: Add function to get device pointer for DMA API
dmaengine: ti: k3-udma: Add support for second resource range from sysfw
dmaengine: ti: k3-udma: Wait for peer teardown completion if supported
...
These are additional updates for the power domain support on OMAP,
moving to an implementation based on device tree information instead of
SoC specific code. This is the latest step in the ongoing process for
moving code out of arch/arm/mach-omap2.
I kept this separate from the other driver changes since it touches
code in multiple areas.
There is one conflict in the dra7.dts file, which adds another node
in a different branch. Watch out for adding the trailing '};'
both times.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=0mXx
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-omap-genpd-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC OMAP GenPD updates from Arnd Bergmann:
"These are additional updates for the power domain support on OMAP,
moving to an implementation based on device tree information instead
of SoC specific code. This is the latest step in the ongoing process
for moving code out of arch/arm/mach-omap2.
I kept this separate from the other driver changes since it touches
code in multiple areas"
* tag 'arm-soc-omap-genpd-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (51 commits)
ARM: OMAP2+: Fix am4 only build after genpd changes
ARM: dts: Configure power domain for omap5 dss
ARM: dts: omap5: add remaining PRM instances
soc: ti: omap-prm: omap5: add genpd support for remaining PRM instances
ARM: OMAP2+: Drop legacy platform data for dra7 gpmc
ARM: dts: Configure interconnect target module for dra7 iva
ARM: dts: dra7: add remaining PRM instances
soc: ti: omap-prm: dra7: add genpd support for remaining PRM instances
clk: ti: dra7: Drop idlest polling from IVA clkctrl clocks
ARM: OMAP2+: Drop legacy platform data for omap4 gpmc
ARM: OMAP2+: Drop legacy platform data for omap4 iva
ARM: dts: Configure power domain for omap4 dsp
ARM: dts: Configure power domain for omap4 dss
ARM: dts: omap4: add remaining PRM instances
soc: ti: omap-prm: omap4: add genpd support for remaining PRM instances
clk: ti: omap4: Drop idlest polling from IVA clkctrl clocks
ARM: OMAP2+: Drop legacy remaining legacy platform data for am4
ARM: dts: Use simple-pm-bus for genpd for am4 l3
ARM: dts: Move am4 l3 noc to a separate node
ARM: dts: Use simple-pm-bus for genpd for am4 l4_per
...
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already support.
This is also known as the SigmaStar SSD202D, and we add support for
the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the Ampere
Altra based "Fii Kudo" server and the Quanta GSJ, both of which are
added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last year's
generation, also added along with its reference board. This one is
still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into low-end
tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM,
and one machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board
for the aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape
LX2162A, which is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based board,
- IEI Puzzle-M801, a rackmount network appliance based on
Marvell Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm
sm8250 and sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook
(sc7180)
- New board variants of the Renesas based "Kingfisher" and
"HiHope" reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with
a few carrier boards.
There is one conflict in mt6577_auxadc.txt, which got replaced in
another tree and modified here, the modification is already part of
the new file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=R47r
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM device tree updates from Arnd Bergmann:
"Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already
support. This is also known as the SigmaStar SSD202D, and we add
support for the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the
Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
which are added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last
year's generation, also added along with its reference board. This
one is still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into
low-end tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM, and one
machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based
board,
- IEI Puzzle-M801, a rackmount network appliance based on Marvell
Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook (sc7180)
- New board variants of the Renesas based "Kingfisher" and "HiHope"
reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
carrier boards"
* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
arm64: dts: sparx5: Add SGPIO devices
arm64: dts: sparx5: Add reset support
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
ARM: mstar: SMP support
ARM: mstar: Wire up smpctrl for SSD201/SSD202D
ARM: mstar: Add smp ctrl registers to infinity2m dtsi
ARM: mstar: Add dts for Honestar ssd201htv2
ARM: mstar: Add chip level dtsi for SSD202D
ARM: mstar: Add common dtsi for SSD201/SSD202D
ARM: mstar: Add infinity2m support
dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
dt-bindings: vendor-prefixes: Add honestar vendor prefix
dt-bindings: mstar: Add binding details for mstar,smpctrl
ARM: mstar: Fill in GPIO controller properties for infinity
ARM: mstar: Add gpio controller to MStar base dtsi
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
...
Add driver code for the SiFive FU740 PRCI IP block. This IP block
handles reset and clock control for the SiFive FU740 device and
implements SoC-level clock tree controls and dividers.
The link of unmatched as follow, and the U740-C000 manual would
be present in the same page as soon.
https://www.sifive.com/boards/hifive-unmatched
This driver contains bug fixes and contributions from
Henry Styles <hes@sifive.com>
Erik Danie <erik.danie@sifive.com>
Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Pragnesh Patel <Pragnesh.patel@sifive.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: Henry Styles <hes@sifive.com>
Cc: Erik Danie <erik.danie@sifive.com>
Cc: Pragnesh Patel <pragnesh.patel@sifive.com>
Link: https://lore.kernel.org/r/20201209094916.17383-4-zong.li@sifive.com
[sboyd@kernel.org: Include header to silence sparse]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- enabled GCOV
- reworked setup of protection map
- added support for more MSCC platforms
- added sysfs boardinfo for Loongson64
- enabled KASLR for Loogson64
- added reset controller for BCM63xx
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=0Sht
-----END PGP SIGNATURE-----
Merge tag 'mips_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- enable GCOV
- rework setup of protection map
- add support for more MSCC platforms
- add sysfs boardinfo for Loongson64
- enable KASLR for Loogson64
- add reset controller for BCM63xx
- cleanups and fixes
* tag 'mips_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (70 commits)
mips: fix Section mismatch in reference
MAINTAINERS: Add linux-mips mailing list to JZ47xx entries
MAINTAINERS: Remove JZ4780 DMA driver entry
MAINTAINERS: chenhc@lemote.com -> chenhuacai@kernel.org
MIPS: Octeon: irq: Alloc desc before configuring IRQ
MIPS: mm: Add back define for PAGE_SHARED
MIPS: Select ARCH_KEEP_MEMBLOCK if DEBUG_KERNEL to enable sysfs memblock debug
mips: lib: uncached: fix non-standard usage of variable 'sp'
MIPS: DTS: img: Fix schema warnings for pwm-leds
MIPS: KASLR: Avoid endless loop in sync_icache if synci_step is zero
MIPS: Move memblock_dump_all() to the end of setup_arch()
MIPS: SMP-CPS: Add support for irq migration when CPU offline
MIPS: OCTEON: Don't add kernel sections into memblock allocator
MIPS: Don't round up kernel sections size for memblock_add()
MIPS: Enable GCOV
MIPS: configs: drop unused BACKLIGHT_GENERIC option
MIPS: Loongson64: Fix up reserving kernel memory range
MIPS: mm: Remove unused is_aligned_hugepage_range
MIPS: No need to check CPU 0 in {loongson3,bmips,octeon}_cpu_disable()
mips: cdmm: fix use-after-free in mips_cdmm_bus_discover
...
This has been a quiet release for the regulator API, a few new drivers
and the usual fixes and cleanup traffic but not much else going on:
- Optimisations for the handling of voltage enumeration, especially
with sparse selector sets, from Claudiu Beznea.
- Support for several ARM SCMI regulators, Dialog DA9121, NXP PF8x00,
Qualcomm PMX55, PM8350 and PM8350c
The addition of the SCMI regulator driver (which controls regulators via
system firmware) means that we've pulled in the support for the underlying
firmware operations from the firmware tree.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl/Xd00ACgkQJNaLcl1U
h9DStgf+JpvomwCLInmIr1GCLbdhYaxmm8YSuMRqbl4cmRq/D/1cyCUJ7nRsSfsT
CcKvFwhH1DwQaMeZJbIilItlM70E7S3lcjUpUZvc0kiBfdSLyNKvpSTnu3olgzJO
L7WQYil1Kj/VSNJjx4WmB9YN+zooV1kcRiBS+3JBnlSac4HTLBtiGCFzHGbU+HSo
D3CN5XdBaHToZhGuOJLvs7rqFr9uErB9kmZ/u/2kByQwiEekxP3s9TjfF5zrPYmM
X9Sg8v44crS6noehzst42GpqJ3TgQzCgIACgHjx2f5ISqApmgF2WK3Tik4NYj4Jm
RFPjJdzTV2ik1LuMsE3aihJ6h3PBYQ==
=Q5YC
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been a quiet release for the regulator API, a few new drivers
and the usual fixes and cleanup traffic but not much else going on:
- Optimisations for the handling of voltage enumeration, especially
with sparse selector sets, from Claudiu Beznea.
- Support for several ARM SCMI regulators, Dialog DA9121, NXP PF8x00,
Qualcomm PMX55, PM8350 and PM8350c
The addition of the SCMI regulator driver (which controls regulators
via system firmware) means that we've pulled in the support for the
underlying firmware operations from the firmware tree"
* tag 'regulator-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (53 commits)
regulator: mc13892-regulator: convert comma to semicolon
regulator: pfuze100: Convert the driver to DT-only
regulator: max14577: Add proper module aliases strings
regulator: da9121: Potential Oops in da9121_assign_chip_model()
regulator: da9121: Fix index used for DT property
regulator: da9121: Remove uninitialised string variable
regulator: axp20x: Fix DLDO2 voltage control register mask for AXP22x
regulator: qcom-rpmh: Add support for PM8350/PM8350c
regulator: dt-bindings: Add PM8350x compatibles
regulator: da9121: include linux/gpio/consumer.h
regulator: da9121: Mark some symbols with static keyword
regulator: da9121: Request IRQ directly and free in release function to avoid masking race
regulator: da9121: add interrupt support
regulator: da9121: add mode support
regulator: da9121: add current support
regulator: da9121: Update registration to support multiple buck variants
regulator: da9121: Add support for device variants via devicetree
regulator: da9121: Add device variant descriptors
regulator: da9121: Add device variant regmaps
regulator: da9121: Add device variants
...
Here is the big USB and thunderbolt pull request for 5.11-rc1.
Nothing major in here, just the grind of constant development to support
new hardware and fix old issues:
- thunderbolt updates for new USB4 hardware
- cdns3 major driver updates
- lots of typec updates and additions as more hardware is available
- usb serial driver updates and fixes
- other tiny USB driver updates
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iKFQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yme2gCfacEYztlnc0fh7PyyatYXgdkspbYAn2ri6mfF
4VY86HYXKqQRDW8w/lSg
=f8KJ
-----END PGP SIGNATURE-----
Merge tag 'usb-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big USB and thunderbolt pull request for 5.11-rc1.
Nothing major in here, just the grind of constant development to
support new hardware and fix old issues:
- thunderbolt updates for new USB4 hardware
- cdns3 major driver updates
- lots of typec updates and additions as more hardware is available
- usb serial driver updates and fixes
- other tiny USB driver updates
All have been in linux-next with no reported issues"
* tag 'usb-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
usb: phy: convert comma to semicolon
usb: ucsi: convert comma to semicolon
usb: typec: tcpm: convert comma to semicolon
usb: typec: tcpm: Update vbus_vsafe0v on init
usb: typec: tcpci: Enable bleed discharge when auto discharge is enabled
usb: typec: Add class for plug alt mode device
USB: typec: tcpci: Add Bleed discharge to POWER_CONTROL definition
USB: typec: tcpm: Add a 30ms room for tPSSourceOn in PR_SWAP
USB: typec: tcpm: Fix PR_SWAP error handling
USB: typec: tcpm: Hard Reset after not receiving a Request
USB: gadget: f_fs: remove likely/unlikely
usb: gadget: f_fs: Re-use SS descriptors for SuperSpeedPlus
USB: gadget: f_midi: setup SuperSpeed Plus descriptors
USB: gadget: f_acm: add support for SuperSpeed Plus
USB: gadget: f_rndis: fix bitrate for SuperSpeed and above
usb: typec: intel_pmc_mux: Configure cable generation value for USB4
MAINTAINERS: Add myself as a reviewer for CADENCE USB3 DRD IP DRIVER
usb: chipidea: ci_hdrc_imx: Use of_device_get_match_data()
usb: chipidea: usbmisc_imx: Use of_device_get_match_data()
usb: cdns3: fix NULL pointer dereference on no platform data
...
Lots of changes (slightly more code increase than usual) at this
time, while most of code changes are ASoC driver-specific.
Here goes some highlight:
Core:
* The new auxiliary bus implementation for Intel DSP, which will
be used by other drivers as well
* Lots of ASoC core cleanups and refactoring
* UBSAN and KCSAN fixes in rawmidi, sequencer and a few others
* Compress-offload API enhancement for the pause during draining
HD- and USB-audio:
* Enhancements of the USB-audio implicit feedback support,
including better full-duplex operations
* Continued CA0132 improvements and fixes
* A few new quirk entries, HDMI audio fixes
ASoC:
* Support for boot time selection of Intel DSP firmware, which
should help distros/users testing new stuff more easily;
the kconfig was moved to boot time option, too
* Some basic DPCM support in audio graph card
* Removal of old pre-DT Freescale drivers
* Support for Allwinner H6 I2S, Analog Devices ADAU1372, Intel
Alderlake-S, GMediatek MT8192, NXP i.MX HDMI and XCVR, Realtek
RT715, Qualcomm SM8250 and simple GPIO based muxes
-----BEGIN PGP SIGNATURE-----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=j9El
-----END PGP SIGNATURE-----
Merge tag 'sound-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Lots of changes (slightly more code increase than usual) at this time,
while most of code changes are ASoC driver-specific.
Here are some highlights:
Core:
- The new auxiliary bus implementation for Intel DSP, which will be
used by other drivers as well
- Lots of ASoC core cleanups and refactoring
- UBSAN and KCSAN fixes in rawmidi, sequencer and a few others
- Compress-offload API enhancement for the pause during draining
HD- and USB-audio:
- Enhancements of the USB-audio implicit feedback support, including
better full-duplex operations
- Continued CA0132 improvements and fixes
- A few new quirk entries, HDMI audio fixes
ASoC:
- Support for boot time selection of Intel DSP firmware, which should
help distros/users testing new stuff more easily; the kconfig was
moved to boot time option, too
- Some basic DPCM support in audio graph card
- Removal of old pre-DT Freescale drivers
- Support for Allwinner H6 I2S, Analog Devices ADAU1372, Intel
Alderlake-S, GMediatek MT8192, NXP i.MX HDMI and XCVR, Realtek
RT715, Qualcomm SM8250 and simple GPIO based muxes"
* tag 'sound-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (445 commits)
ALSA: pcm: oss: Fix potential out-of-bounds shift
ALSA: usb-audio: Fix potential out-of-bounds shift
ALSA: hda/ca0132 - Add ZxR surround DAC setup.
ALSA: hda/ca0132 - Add 8051 PLL write helper functions.
ALSA: hda/hdmi: packet buffer index must be set before reading value
ASoC: SOF: imx: update kernel-doc description
ASoC: mediatek: mt8183: delete some unreachable code
ASoC: mediatek: mt8183: add PM ops to machine drivers
ASoC: topology: Fix wrong size check
ASoC: topology: Add missing size check
ASoC: SOF: Intel: hda: fix the condition passed to sof_dev_dbg_or_err
ASoC: SOF: modify the SOF_DBG flags
ASoC: SOF: Intel: hda: remove duplicated status dump
ASoC: rt1015p: delay 300ms after SDB pulling high for calibration
ASoC: rt1015p: move SDB control from trigger to DAPM
ASoC: wm_adsp: remove "ctl" from list on error in wm_adsp_create_control()
ALSA: usb-audio: Fix control 'access overflow' errors from chmap
ALSA: hda/hdmi: always print pin NIDs as hexadecimal
ALSA: hda/realtek - Add supported for more Lenovo ALC285 Headset Button
ALSA: hda/ca0132 - Remove now unnecessary DSP setup functions.
...
Core:
- support "prefer busy polling" NAPI operation mode, where we defer softirq
for some time expecting applications to periodically busy poll
- AF_XDP: improve efficiency by more batching and hindering
the adjacency cache prefetcher
- af_packet: make packet_fanout.arr size configurable up to 64K
- tcp: optimize TCP zero copy receive in presence of partial or unaligned
reads making zero copy a performance win for much smaller messages
- XDP: add bulk APIs for returning / freeing frames
- sched: support fragmenting IP packets as they come out of conntrack
- net: allow virtual netdevs to forward UDP L4 and fraglist GSO skbs
BPF:
- BPF switch from crude rlimit-based to memcg-based memory accounting
- BPF type format information for kernel modules and related tracing
enhancements
- BPF implement task local storage for BPF LSM
- allow the FENTRY/FEXIT/RAW_TP tracing programs to use bpf_sk_storage
Protocols:
- mptcp: improve multiple xmit streams support, memory accounting and
many smaller improvements
- TLS: support CHACHA20-POLY1305 cipher
- seg6: add support for SRv6 End.DT4/DT6 behavior
- sctp: Implement RFC 6951: UDP Encapsulation of SCTP
- ppp_generic: add ability to bridge channels directly
- bridge: Connectivity Fault Management (CFM) support as is defined in
IEEE 802.1Q section 12.14.
Drivers:
- mlx5: make use of the new auxiliary bus to organize the driver internals
- mlx5: more accurate port TX timestamping support
- mlxsw:
- improve the efficiency of offloaded next hop updates by using
the new nexthop object API
- support blackhole nexthops
- support IEEE 802.1ad (Q-in-Q) bridging
- rtw88: major bluetooth co-existance improvements
- iwlwifi: support new 6 GHz frequency band
- ath11k: Fast Initial Link Setup (FILS)
- mt7915: dual band concurrent (DBDC) support
- net: ipa: add basic support for IPA v4.5
Refactor:
- a few pieces of in_interrupt() cleanup work from Sebastian Andrzej Siewior
- phy: add support for shared interrupts; get rid of multiple driver
APIs and have the drivers write a full IRQ handler, slight growth
of driver code should be compensated by the simpler API which
also allows shared IRQs
- add common code for handling netdev per-cpu counters
- move TX packet re-allocation from Ethernet switch tag drivers to
a central place
- improve efficiency and rename nla_strlcpy
- number of W=1 warning cleanups as we now catch those in a patchwork
build bot
Old code removal:
- wan: delete the DLCI / SDLA drivers
- wimax: move to staging
- wifi: remove old WDS wifi bridging support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=GXs1
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- support "prefer busy polling" NAPI operation mode, where we defer
softirq for some time expecting applications to periodically busy
poll
- AF_XDP: improve efficiency by more batching and hindering the
adjacency cache prefetcher
- af_packet: make packet_fanout.arr size configurable up to 64K
- tcp: optimize TCP zero copy receive in presence of partial or
unaligned reads making zero copy a performance win for much smaller
messages
- XDP: add bulk APIs for returning / freeing frames
- sched: support fragmenting IP packets as they come out of conntrack
- net: allow virtual netdevs to forward UDP L4 and fraglist GSO skbs
BPF:
- BPF switch from crude rlimit-based to memcg-based memory accounting
- BPF type format information for kernel modules and related tracing
enhancements
- BPF implement task local storage for BPF LSM
- allow the FENTRY/FEXIT/RAW_TP tracing programs to use
bpf_sk_storage
Protocols:
- mptcp: improve multiple xmit streams support, memory accounting and
many smaller improvements
- TLS: support CHACHA20-POLY1305 cipher
- seg6: add support for SRv6 End.DT4/DT6 behavior
- sctp: Implement RFC 6951: UDP Encapsulation of SCTP
- ppp_generic: add ability to bridge channels directly
- bridge: Connectivity Fault Management (CFM) support as is defined
in IEEE 802.1Q section 12.14.
Drivers:
- mlx5: make use of the new auxiliary bus to organize the driver
internals
- mlx5: more accurate port TX timestamping support
- mlxsw:
- improve the efficiency of offloaded next hop updates by using
the new nexthop object API
- support blackhole nexthops
- support IEEE 802.1ad (Q-in-Q) bridging
- rtw88: major bluetooth co-existance improvements
- iwlwifi: support new 6 GHz frequency band
- ath11k: Fast Initial Link Setup (FILS)
- mt7915: dual band concurrent (DBDC) support
- net: ipa: add basic support for IPA v4.5
Refactor:
- a few pieces of in_interrupt() cleanup work from Sebastian Andrzej
Siewior
- phy: add support for shared interrupts; get rid of multiple driver
APIs and have the drivers write a full IRQ handler, slight growth
of driver code should be compensated by the simpler API which also
allows shared IRQs
- add common code for handling netdev per-cpu counters
- move TX packet re-allocation from Ethernet switch tag drivers to a
central place
- improve efficiency and rename nla_strlcpy
- number of W=1 warning cleanups as we now catch those in a patchwork
build bot
Old code removal:
- wan: delete the DLCI / SDLA drivers
- wimax: move to staging
- wifi: remove old WDS wifi bridging support"
* tag 'net-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1922 commits)
net: hns3: fix expression that is currently always true
net: fix proc_fs init handling in af_packet and tls
nfc: pn533: convert comma to semicolon
af_vsock: Assign the vsock transport considering the vsock address flags
af_vsock: Set VMADDR_FLAG_TO_HOST flag on the receive path
vsock_addr: Check for supported flag values
vm_sockets: Add VMADDR_FLAG_TO_HOST vsock flag
vm_sockets: Add flags field in the vsock address data structure
net: Disable NETIF_F_HW_TLS_TX when HW_CSUM is disabled
tcp: Add logic to check for SYN w/ data in tcp_simple_retransmit
net: mscc: ocelot: install MAC addresses in .ndo_set_rx_mode from process context
nfc: s3fwrn5: Release the nfc firmware
net: vxget: clean up sparse warnings
mlxsw: spectrum_router: Use eXtended mezzanine to offload IPv4 router
mlxsw: spectrum: Set KVH XLT cache mode for Spectrum2/3
mlxsw: spectrum_router_xm: Introduce basic XM cache flushing
mlxsw: reg: Add Router LPM Cache Enable Register
mlxsw: reg: Add Router LPM Cache ML Delete Register
mlxsw: spectrum_router_xm: Implement L-value tracking for M-index
mlxsw: reg: Add XM Router M Table Register
...
This adds the RPMH clocks present in SM8350 SoC
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201208064702.3654324-3-vkoul@kernel.org
[sboyd@kernel.org: Move sdx55 to the right place]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Header adds defines for the gpio number of each pad from the driver view.
The gpio block seems to have enough registers for 128 lines but what line
is mapped to a physical pin depends on the chip. The gpio block also seems
to contain some registers that are not related to gpio but needed somewhere
to go.
Because of the above the driver itself uses the index of a pin's offset in
an array of the possible offsets for a chip as the gpio number.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm driver updates for v5.11
This adds support for the core power domains on MSM8916, MSM8939, SDM660
and SDX55. It adds SM8150 support to the last-level cache controller
driver and it makes it possible to build the Command DB and RPMh drivers
as modules.
It also contains a slew of smaller cleanups, style and bug fixes
throughout the various drivers.
* tag 'qcom-drivers-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (39 commits)
soc: qcom: rpmhpd: Add SDX55 power domains
dt-bindings: power: Add rpm power domain bindings for sdx55
soc: qcom: rpmh: Use __fill_rpmh_msg API during rpmh_write()
samples: qmi: Constify static qmi ops
soc: qcom: pdr: Constify static qmi structs
soc: qcom: initialize local variable
soc: qcom: socinfo: add soc ids for msm8953 variants
soc: qcom: geni: Remove "iova" check
soc: qcom: llcc: Add configuration data for SM8150
dt-bindings: msm: Add LLCC for SM8150
soc: qcom: rpmh: Fix possible doc-rot in rpmh_write()'s header
soc: qcom: kryo-l2-accessors: Fix misnaming of 'val'
soc: qcom: rpmhpd: Provide some missing struct member descriptions
soc: qcom: llcc-qcom: Fix expected kernel-doc formatting
soc: qcom: smp2p: Remove unused struct attribute provide another
soc: qcom: wcnss_ctrl: Demote non-conformant struct header and fix function headers
soc: qcom: smsm: Fix some kernel-doc formatting and naming problems
soc: qcom: smem: Fix formatting and missing documentation issues
soc: qcom: qcom-geni-se: Fix misnamed function parameter 'rx_rfr'
soc: qcom: qcom_aoss: Add missing description for 'cooling_devs'
...
Link: https://lore.kernel.org/r/20201130190142.345246-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Quite some patches that update vendor-prefixes.yaml and fsl.yaml to
document missing board compatibles and add new board compatibles.
- A couple of patches from Dong Aisheng to update imx-scu firmware and
imx-lpcg clock bindings for new SCU two cells clock support.
- A couple of net bindings update from Ioana Ciornei to complete the
MAC/PCS/PHY representation on DPAA2 devices.
- Document watchdog compatibles for all i.MX and Layerscape devices.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl/HlOYUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM4yegf/eP6henuph6c+Ay/y7Ia4V51UY4ot
Sb9pJatgaX4GmFowfztltd//gJMtpHnYbqAsXhk2hkRZ7h0hFIIji2Dp7knq3naD
rQykAmT4eWy1CuQFq86XvFaqHc5AVuygBpMmP6nSFDBzBeqDRQ+q813aUpQdUlUH
iAeN2Ov62U+4kEc0AxF2mNNcGW1/ikKcFT5nJmJGmgUKuwSUSJ0l09MvXHhQeEjr
//gswg/5XU4tweEjAHeEJKM60XLtRFdmoLnz/0nDlLY0BXfBYRpicvNXzxDWEPOd
qdf20NOWyz2UUcmMgy1vpVJKHQumSDNxB9M0FwtkcB8+x0YjE4gB8AxUNA==
=YiM1
-----END PGP SIGNATURE-----
Merge tag 'imx-bindings-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX DT bindings update for 5.11:
- Quite some patches that update vendor-prefixes.yaml and fsl.yaml to
document missing board compatibles and add new board compatibles.
- A couple of patches from Dong Aisheng to update imx-scu firmware and
imx-lpcg clock bindings for new SCU two cells clock support.
- A couple of net bindings update from Ioana Ciornei to complete the
MAC/PCS/PHY representation on DPAA2 devices.
- Document watchdog compatibles for all i.MX and Layerscape devices.
* tag 'imx-bindings-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (35 commits)
dt-bindings: arm: fsl: add Protonic WD3 board
dt-bindings: vendor-prefixes: add "virtual" prefix
dt-bindings: fsl: add kamstrup flex concentrator to schema
dt-bindings: arm: fsl: document i.MX7S boards
dt-bindings: arm: fsl: document SolidRun LX2160A boards
dt-bindings: arm: fsl: document LS1012A FRWY board
dt-bindings: arm: fsl: add Van der Laan LANMCU board
dt-bindings: arm: fsl: add Altesco I6P board
dt-bindings: vendor-prefixes: Add an entry for Altus-Escon-Company
dt-bindings: net: add the 10gbase-r connection type
dt-bindings: net: add the DPAA2 MAC DTS definition
dt-bindings: fsl: add compatible for LX2162A QDS Board
dt-bindings: vendor-prefixes: Add an entry for Van der Laan b.v.
dt-bindings: arm: fsl: document i.MX7D boards
dt-bindings: arm: fsl: document i.MX6ULL boards
dt-bindings: arm: fsl: document i.MX6UL boards
dt-bindings: arm: fsl: document i.MX6SX boards
dt-bindings: arm: fsl: document i.MX6SL boards
dt-bindings: arm: fsl: document i.MX6QP boards
dt-bindings: arm: fsl: document i.MX6Q boards
...
Link: https://lore.kernel.org/r/20201202142717.9262-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
For SM8250 the recently introduced support for handling boot-loader
stream mappings in the ARM SMMU allow us to enable this, and thereby USB
controller and PHY, SDHCI controller and FastRPC, as well as support for
the SM8250 HDK board has been added. Additionally PRNG and RTC is
enabled.
Similarly for SM8150, the ARM SMMU could be added which allows the
secondary USB controller and PHYs, as well as WiFi to be added and
support for the SM8150 HDK board to be introduced. Additionally
Coresight and support for the last-level cache controller was added.
MSM8916 finally has VDDCX and VDDMX removed as regulators and are now
handled by the rpmpd driver for the devices controlling them. The
Longsheer L8150 gains touchscreen, sensors, vibrator and LED support.
MSM8992 gains USB and SDHCI support as well as an I2C controller and the
associated RMI4 based touchscreen for the Lumia 950.
MSM8994 also gains USB and SDHCI support, as well as VADC and temp-alarm
support. Then support for the Lumia 950 XL is added.
SDM845 gains interconnect properties for a number of devices and the
GENI wrappers gains iommu stream configuration, which means DMA
operations on e.g. I2C now works. The Lenovo Yoga C630 finally has the
SMMU enabled, a few fixes and the description of the eDP bridge and
panel means that the laptop can now boot mainline with working display,
GPU, WiFi and audio.
SC7180 gains a slew of smaller improvements and fixes.
-----BEGIN PGP SIGNATURE-----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=lkn4
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for 5.11
For SM8250 the recently introduced support for handling boot-loader
stream mappings in the ARM SMMU allow us to enable this, and thereby USB
controller and PHY, SDHCI controller and FastRPC, as well as support for
the SM8250 HDK board has been added. Additionally PRNG and RTC is
enabled.
Similarly for SM8150, the ARM SMMU could be added which allows the
secondary USB controller and PHYs, as well as WiFi to be added and
support for the SM8150 HDK board to be introduced. Additionally
Coresight and support for the last-level cache controller was added.
MSM8916 finally has VDDCX and VDDMX removed as regulators and are now
handled by the rpmpd driver for the devices controlling them. The
Longsheer L8150 gains touchscreen, sensors, vibrator and LED support.
MSM8992 gains USB and SDHCI support as well as an I2C controller and the
associated RMI4 based touchscreen for the Lumia 950.
MSM8994 also gains USB and SDHCI support, as well as VADC and temp-alarm
support. Then support for the Lumia 950 XL is added.
SDM845 gains interconnect properties for a number of devices and the
GENI wrappers gains iommu stream configuration, which means DMA
operations on e.g. I2C now works. The Lenovo Yoga C630 finally has the
SMMU enabled, a few fixes and the description of the eDP bridge and
panel means that the laptop can now boot mainline with working display,
GPU, WiFi and audio.
SC7180 gains a slew of smaller improvements and fixes.
* tag 'qcom-arm64-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (93 commits)
arm64: dts: qcom: c630: Define eDP bridge and panel
arm64: dts: qcom: c630: Fix pinctrl pins properties
arm64: dts: qcom: c630: Polish i2c-hid devices
arm64: dts: qcom: sc7180: Add lpass cpu node for I2S driver
arm64: dts: sdm845: Add interconnect properties for QUP
interconnect: qcom: sdm845: Add the missing nodes for QUP
dt-bindings: interconnect: sdm845: Add IDs for the QUP ports
arm64: dts: qcom: c630: Expose LID events
arm64: dts: qcom: c630: Re-enable apps_smmu
dts: qcom: sdm845: Add dt entries to support crypto engine.
arm64: dts: qcom: qrb5165-rb5: Add support for MCP2518FD
arm64: dts: qcom: sdm845: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: use GIC_SPI for IPA interrupts
arm64: dts: qcom: sc7180: limit IPA iommu streams
arm64: dts: qcom: sm8150: Add Coresight support
arm64: dts: qcom: sc7180-trogdor: Make pp3300_a the default supply for pp3300_hub
arm64: dts: qcom: sc7180: Add DDR/L3 votes for the pro variant
arm64: dts: qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite
arm64: dts: qcom: sc7180-trogdor: add "pen-insert" label for trogdor
arm64: qcom: sc7180: trogdor: Add ADC nodes and thermal zone for charger thermistor
...
Link: https://lore.kernel.org/r/20201130190131.345187-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add device tree bindings for global clock controller on SDX55 SoCs.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201126072844.35370-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
To avoid future mistakes in the device tree for the clockgen module, add
constants for the clockgen subtype as well as a macro for the PLL
divider.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201108185113.31377-4-michael@walle.cc
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Header adds defines for the gpio number of each pad from the driver view.
The gpio block seems to have enough registers for 128 lines but what line
is mapped to a physical pin depends on the chip. The gpio block also seems
to contain some registers that are not related to gpio but needed somewhere
to go.
Because of the above the driver itself uses the index of a pin's offset in
an array of the possible offsets for a chip as the gpio number.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201129110803.2461700-2-daniel@0x0f.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use a unique include guard for the Tegra186 GPIO DT bindings header to
avoid clashes with the DT bindings header for earlier chips.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201127140852.123192-2-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new OST has one global timer and two or four percpu timers, so there
will be three combinations in the upcoming new OST driver: the original
GLOBAL_TIMER + PERCPU_TIMER, the new GLOBAL_TIMER + PERCPU_TIMER0/1 and
GLOBAL_TIMER + PERCPU_TIMER0/1/2/3, For this, add the macro definition
about OST_CLK_PERCPU_TIMER0/1/2/3. And in order to ensure that all the
combinations work normally, the original ABI values of OST_CLK_PERCPU_TIMER
and OST_CLK_GLOBAL_TIMER need to be exchanged to ensure that in any
combinations, the clock can be registered (by calling clk_hw_register())
from index 0.
Before this patch, OST_CLK_PERCPU_TIMER and OST_CLK_GLOBAL_TIMER are only
used in two places, one is when using "assigned-clocks" to configure the
clocks in the DTS file; the other is when registering the clocks in the
sysost driver. When the values of these two ABIs are exchanged, the ABI
value used by sysost driver when registering the clock, and the ABI value
used by DTS when configuring the clock using "assigned-clocks" will also
change accordingly. Therefore, there is no situation that causes the wrong
clock to the configured. Therefore, exchanging ABI values will not cause
errors in the existing codes when registering and configuring the clocks.
Currently, in the mainline, only X1000 and X1830 are using sysost driver,
and the upcoming X2000 will also use sysost driver. This patch has been
tested on all three SoCs and all works fine.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201026155842.10196-2-zhouyanjie@wanyeetech.com
Update bindings for the Dialog Semiconductor DA9121 voltage regulator to
add device variants.
Because several variants have multiple regulators, and to regard potential
to add GPIO support in future, the 'regulators' sub-node is added,
following the precedent set by other multi-regulator devices, including
the DA9211 family. This breaks compatibility with the original submission
by Vincent Whitchurch - but as this is still in for-next, the alignment
could be made before upstreaming occurs.
Signed-off-by: Adam Ward <Adam.Ward.opensource@diasemi.com>
Link: https://lore.kernel.org/r/0606d3ded5fef4c38760246146f197db4ce3a374.1606755367.git.Adam.Ward.opensource@diasemi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The QUP ports exist in the topology, but are not exposed as an
endpoints in DT. Fix this by creating IDs and attach them to their
NoCs, so that the various QUP drivers (i2c/spi/uart etc.) are able
to request their interconnect paths and scale their bandwidth.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201105135211.7160-1-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
- add support for new power domain driver.
- add support for mt8183 and mt8192
devapc:
- add support for the devapc device found on mt6779 to identify of
malicious bus accesses from a controller to a device
mmsys:
- move DDP routing IDs into the driver
cmdq:
- drop timeout handler support as not usefull
scpsys:
- print warning on theoretical error
-----BEGIN PGP SIGNATURE-----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=mQNT
-----END PGP SIGNATURE-----
Merge tag 'v5.10-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
power-domains:
- add support for new power domain driver.
- add support for mt8183 and mt8192
devapc:
- add support for the devapc device found on mt6779 to identify of
malicious bus accesses from a controller to a device
mmsys:
- move DDP routing IDs into the driver
cmdq:
- drop timeout handler support as not usefull
scpsys:
- print warning on theoretical error
* tag 'v5.10-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (21 commits)
soc: mediatek: mmsys: Use devm_platform_ioremap_resource()
soc / drm: mediatek: Move DDP component defines into mtk-mmsys.h
soc: mediatek: add mt6779 devapc driver
dt-bindings: devapc: add bindings for mtk-devapc
soc / drm: mediatek: cmdq: Remove timeout handler in helper function
soc: mediatek: pm-domains: Add support for mt8192
soc: mediatek: pm-domains: Add default power off flag
soc: mediatek: pm-domains: Add support for mt8183
soc: mediatek: pm-domains: Allow bus protection to ignore clear ack
soc: mediatek: pm-domains: Add subsystem clocks
soc: mediatek: pm-domains: Add extra sram control
soc: mediatek: pm-domains: Add SMI block as bus protection block
soc: mediatek: pm_domains: Make bus protection generic
soc: mediatek: pm-domains: Add bus protection protocol
soc: mediatek: Add MediaTek SCPSYS power domains
dt-bindings: power: Add MT8192 power domains
dt-bindings: power: Add MT8183 power domains
dt-bindings: power: Add bindings for the Mediatek SCPSYS power domains controller
mfd: syscon: Add syscon_regmap_lookup_by_phandle_optional() function.
MAINTAINERS: change mediatek wiki page
...
Link: https://lore.kernel.org/r/b03fe343-e183-c6f3-f2dc-4c58aae3146b@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add clock id forc CE clock resource which is required to bring up the
crypto engine on sdm845.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201119155233.3974286-2-thara.gopinath@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Similar to what we've done for IPU and DSP let's ignore the status bit
for the IVA clkctrl register.
The clkctrl status won't change unless the related rstctrl is deasserted,
and the rstctrl status won't change unless the clkctrl is enabled.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BCM6318 SoCs have a reset controller for certain components.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <F.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
BCM63268 SoCs have a reset controller for certain components.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
BCM6368 SoCs have a reset controller for certain components.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
BCM6362 SoCs have a reset controller for certain components.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
BCM6358 SoCs have a reset controller for certain components.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
BCM6328 SoCs have a reset controller for certain components.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Always ON Clock controller is a block inside LPASS which controls
1 Glitch free muxes to LPASS codec Macros.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20201026120221.18984-3-srinivas.kandagatla@linaro.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Camera Subsystem clock provider have a bunch of generic properties
that are needed in a device tree. Add a YAML schemas for those.
Add clock ids for camera clocks which are required to bring the camera
subsystem out of reset.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1602873815-1677-4-git-send-email-tdas@codeaurora.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This change adds frs-typec-current which allows setting the initial current
capability of the new source when vSafe5V is applied during PD3.0
sink Fast Role Swap.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201020093627.256885-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Tegra X1 TRM, there are missing swgroups in the
tegra210_swgroups list. So this patch adds them in bindings.
Note that the TEGRA_SWGROUP_GPU (in list) should be actually
TEGRA_SWGROUP_GPUB (in TRM), yet TEGRA_SWGROUP_GPU (in TRM)
is not being used -- only TEGRA_SWGROUP_GPUB (in TRM) is. So
this patch does not add TEGRA_SWGROUP_GPU (in TRM) and keeps
TEGRA_SWGROUP_GPU (in list) as it is.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201008003746.25659-5-nicoleotsuka@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The change removes the platform_data include/definition. It only contains
some values for the MICBIAS.
These are moved into 'dt-bindings/sound/adi,adau1977.h' so that they can be
used inside device-trees. When moving then, they need to be converted to
pre-compiler defines, so that the DT compiler can understand them.
The driver then, also needs to include the new
'dt-bindings/sound/adi,adau1977.h' file.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201019105313.24862-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MSM8916 has two RPM power domains: VDDCX and VDDMX.
Add the device tree bindings to manage them through rpmpd.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
MSM8939 has three RPM power domains: VDDCX and VDDMX and VDDMDCX.
Add the device tree bindings to manage them through rpmpd.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Link: https://lore.kernel.org/r/20200930100145.9457-2-jun.nie@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the new bindings for SDM660 rpmpd power domains.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20201018122620.9735-2-kholk11@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
MX8QM and MX8QXP LPCG Clocks are mostly the same except they may reside
in different subsystems across CPUs and also vary a bit on the availability.
Same as SCU clock, we want to move the clock definition into device tree
which can fully decouple the dependency of Clock ID definition from device
tree and make us be able to write a fully generic lpcg clock driver.
And we can also use the existence of clock nodes in device tree to address
the device and clock availability differences across different SoCs.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: devicetree@vger.kernel.org
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Various driver updates for platforms. A bulk of this is smaller fixes or
cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs
and platforms.
-----BEGIN PGP SIGNATURE-----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=tfPb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
I had queued up a batch of fixes that got a bit close to the release for
sending in before the merge window opened, so I'm including them in the
batch of pull requests instead. They're mostly smaller DT tweaks and
fixes, the usual mix that we tend to have through the releases.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl+TTg8PHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3kQUP/j1HTcEOghLsUPAiV+kz1qEWjS1tcm4/OV+b
+Tp4pQh5Fy++iXS9yWmCgr/kMxJ4EQkCZERO+8a1VNBms/+0j3KiFuiGsZo0rKZU
QdJvY3q8JYoLYdbyYJ8B7WAT6oS0giBoskGT6FRiwPC7uqM7va1KZOtNeESblt+6
Ty4w5ognXbAvSLz+2VaTZTLbO7fbvd3oSwmbnN7n/qhoRPwaNExJHXTI057ekh4Y
XqjGbYYTwY+Cdm8DkI1Dz2EPKegmSaVxS7+xzacNosx0559qe3pqrZ5OqrTui00Y
/2T5caepAAjdEQsX6es2+mKRRXXWPRJMzHegv/mWvqJ68DPJZLgoHFcY2xy4cclr
ALyc96rEbJTQw5jgoJO1waD6vMZOA7EqE3IXREtxcK8xYRvnK6Od8BJt7lCvB7jN
Ws6U8udqPmeC+PUV9yhBhS8eR/S8MjeQfPK9h0xqqLEhHXqFTeqLHk3EompUaIsy
BwPmPuZI7MBrtwXvrpbdd6I2iw/7XetIrtvSO6Z/d7iZYlf49WJhh6gBtPRnOKGX
zOc90ohFjw/oMFoMpCHsXzyzrwtd/AUqEu/ZRV/yr4yvkpjfpwIRN/cTsN32nRYy
Oi3BTSxow88U7CxZTwkWtwoB+alJ0ZKh3QeyLa/dwiMgj+eUc900kZLqroEMNXO1
1JWG9qL4
=tvbv
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I had queued up a batch of fixes that got a bit close to the release
for sending in before the merge window opened, so I'm including them
in the merge window batch instead.
Mostly smaller DT tweaks and fixes, the usual mix that we tend to have
through the releases"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: iwg20d-q7-common: Fix touch controller probe failure
ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails
ARM: dts: am33xx: modify AM33XX_IOPAD for #pinctrl-cells = 2
soc: actions: include header to fix missing prototype
arm64: dts: ti: k3-j721e: Rename mux header and update macro names
soc: qcom: pdr: Fixup array type of get_domain_list_resp message
arm64: dts: qcom: pm660: Fix missing pound sign in interrupt-cells
arm64: dts: qcom: kitakami: Temporarily disable SDHCI1
arm64: dts: sdm630: Temporarily disable SMMUs by default
arm64: dts: sdm845: Fixup OPP table for all qup devices
arm64: dts: allwinner: h5: remove Mali GPU PMU module
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix dcdc1 regulator
soc: xilinx: Fix error code in zynqmp_pm_probe()
of various clk driver updates. The biggest driver updates in terms of lines of
code is the Allwinner driver, closely followed by the Qualcomm and Mediatek
drivers. All of those hit high because we add so many lines of clk data. Coming
in fourth place is i.MX which also adds a bunch of clk data. This accounts for
the new driver additions this time around.
Otherwise the patches are lots of little cleanups and fixes for various clk
drivers that have baked in linux-next for a while. I suppose one highlight or
theme is that more clk drivers are being updated to work as modules, which is
interesting to see such critical SoC infrastructure work as a loadable module.
New Drivers:
- Support qcom SM8150/SM8250 video and display clks
- Support Mediatek MT8167 clks
- Add clock for CRC block found on vf610 SoCs
- Add support for the Renesas R-Car V3U (R8A779A0) SoC
- Add support for the VSP for Resizing clock on Renesas RZ/G1H
- Support Allwinner A100 SoC clks
Removed Drivers:
- Remove i.MX21 clock driver, as i.MX21 platform support is being dropped
Updates:
- Change how qcom's display port clks work
- Small non-critical fixes for TI clk driver
- Remove various unused variables in clk drivers
- Allow Rockchip clk driver to be a module
- Remove most __clk_lookup() calls in Samsung drivers (yay!)
- Support building i.MX ARMv8 platforms clock driver as module
- Some kerneldoc fixes here and there
- A couple of minor i.MX clk data corrections
- Update audio clock inverter and fdiv2 flag on Amlogic g12
- Make amlogic clk drivers configurable in Kconfig
- Fix Renesas VSP clock names to match corrected hardware documentation
- Sigma-delta modulation on Allwinner R40
- Various fixes for at91 clk driver
- Use semicolons instead of commas in some places
- Mark some variables const so they can move to RO memory
-----BEGIN PGP SIGNATURE-----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=sKI8
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This contains no changes to the core framework. It is a collection of
various clk driver updates.
The biggest driver updates in terms of lines of code is the Allwinner
driver, closely followed by the Qualcomm and Mediatek drivers. All of
those hit high because we add so many lines of clk data. Coming in
fourth place is i.MX which also adds a bunch of clk data. This
accounts for the new driver additions this time around.
Otherwise the patches are lots of little cleanups and fixes for
various clk drivers that have baked in linux-next for a while. I
suppose one highlight or theme is that more clk drivers are being
updated to work as modules, which is interesting to see such critical
SoC infrastructure work as a loadable module.
New Drivers:
- Support qcom SM8150/SM8250 video and display clks
- Support Mediatek MT8167 clks
- Add clock for CRC block found on vf610 SoCs
- Add support for the Renesas R-Car V3U (R8A779A0) SoC
- Add support for the VSP for Resizing clock on Renesas RZ/G1H
- Support Allwinner A100 SoC clks
Removed Drivers:
- Remove i.MX21 clock driver, as i.MX21 platform support is being
dropped
Updates:
- Change how qcom's display port clks work
- Small non-critical fixes for TI clk driver
- Remove various unused variables in clk drivers
- Allow Rockchip clk driver to be a module
- Remove most __clk_lookup() calls in Samsung drivers (yay!)
- Support building i.MX ARMv8 platforms clock driver as module
- Some kerneldoc fixes here and there
- A couple of minor i.MX clk data corrections
- Update audio clock inverter and fdiv2 flag on Amlogic g12
- Make amlogic clk drivers configurable in Kconfig
- Fix Renesas VSP clock names to match corrected hardware
documentation
- Sigma-delta modulation on Allwinner R40
- Various fixes for at91 clk driver
- Use semicolons instead of commas in some places
- Mark some variables const so they can move to RO memory"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (102 commits)
clk: imx8mq: Fix usdhc parents order
clk: qcom: gdsc: Keep RETAIN_FF bit set if gdsc is already on
clk: Restrict CLK_HSDK to ARC_SOC_HSDK
clk: at91: sam9x60: support only two programmable clocks
clk: ingenic: Respect CLK_SET_RATE_PARENT in .round_rate
clk: ingenic: Don't tag custom clocks with CLK_SET_RATE_PARENT
clk: ingenic: Don't use CLK_SET_RATE_GATE for PLL
clk: ingenic: Use readl_poll_timeout instead of custom loop
clk: ingenic: Use to_clk_info() macro for all clocks
clk: bcm2835: add missing release if devm_clk_hw_register fails
clk: at91: clk-sam9x60-pll: remove unused variable
clk: at91: clk-main: update key before writing AT91_CKGR_MOR
clk: at91: remove the checking of parent_name
clk: clk-prima2: fix return value check in prima2_clk_init()
clk: mmp2: Fix the display clock divider base
clk: pxa: Constify static struct clk_ops
clk: baikal-t1: Mark Ethernet PLL as critical
clk: qoriq: modify MAX_PLL_DIV to 32
clk: axi-clkgen: Set power bits for fractional mode
clk: axi-clkgen: Add support for fractional dividers
...
- Support qcom SM8150/SM8250 video and display clks
- Change how qcom's display port clks work
* clk-ingenic:
clk: ingenic: Respect CLK_SET_RATE_PARENT in .round_rate
clk: ingenic: Don't tag custom clocks with CLK_SET_RATE_PARENT
clk: ingenic: Don't use CLK_SET_RATE_GATE for PLL
clk: ingenic: Use readl_poll_timeout instead of custom loop
clk: ingenic: Use to_clk_info() macro for all clocks
* clk-at91:
clk: at91: sam9x60: support only two programmable clocks
clk: at91: clk-sam9x60-pll: remove unused variable
clk: at91: clk-main: update key before writing AT91_CKGR_MOR
clk: at91: remove the checking of parent_name
* clk-kconfig:
clk: Restrict CLK_HSDK to ARC_SOC_HSDK
* clk-imx:
clk: imx8mq: Fix usdhc parents order
clk: imx: imx21: Remove clock driver
clk: imx: gate2: Fix a few typos
clk: imx: Fix and update kerneldoc
clk: imx: fix i.MX7D peripheral clk mux flags
clk: imx: fix composite peripheral flags
clk: imx: Correct the memrepair clock on imx8mp
clk: imx: Correct the root clk of media ldb on imx8mp
clk: imx: vf610: Add CRC clock
clk: imx: Explicitly include bits.h
clk: imx8qxp: Support building i.MX8QXP clock driver as module
clk: imx8m: Support module build
clk: imx: Add clock configuration for ARMv7 platforms
clk: imx: Support building i.MX common clock driver as module
clk: composite: Export clk_hw_register_composite()
clk: imx6sl: Use BIT(x) to avoid shifting signed 32-bit value by 31 bits
* clk-qcom:
clk: qcom: gdsc: Keep RETAIN_FF bit set if gdsc is already on
clk: qcom: Add display clock controller driver for SM8150 and SM8250
dt-bindings: clock: add QCOM SM8150 and SM8250 display clock bindings
clk: qcom: add video clock controller driver for SM8250
clk: qcom: add video clock controller driver for SM8150
dt-bindings: clock: add SM8250 QCOM video clock bindings
dt-bindings: clock: add SM8150 QCOM video clock bindings
dt-bindings: clock: combine qcom,sdm845-videocc and qcom,sc7180-videocc
clk: qcom: gcc-msm8994: Add missing clocks, resets and GDSCs
clk/qcom: fix spelling typo
clk: qcom: gcc-sdm660: Fix wrong parent_map
clk: qcom: dispcc: Update DP clk ops for phy design
clk: qcom: gcc-msm8939: remove defined but not used variables
clk: qcom: ipq8074: make pcie0_rchng_clk_src static
* clk-prima2:
clk: clk-prima2: fix return value check in prima2_clk_init()
* clk-bcm:
clk: bcm2835: add missing release if devm_clk_hw_register fails
clk: bcm: rpi: Add register to control pixel bvb clk
power-supply core:
* Add wireless type
* Properly document current direction
battery/charger driver changes:
* New fuel-gauge/charger driver for RN5T618/RN5T619
* New charger driver for BQ25980, BQ25975 and BQ25960
* bq27xxx-battery: add support for TI bq34z100
* gpio-charger: convert to GPIO descriptors
* gpio-charger: add optional support for charge current limiting
* max17040: add support for max17041, max17043, max17044
* max17040: add support for max17048, max17049, max17058, max17059
* smb347-charger: add DT support
* smb247-charger: add SMB345 and SMB358 support
* simple-battery: add temperature properties
* lots of minor fixes, cleanups and DT binding YAML conversions
reset drivers:
* ocelot: Add support for Sparx5
-----BEGIN PGP SIGNATURE-----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=QtfI
-----END PGP SIGNATURE-----
Merge tag 'for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- add wireless type
- properly document current direction
Battery/charger driver changes:
- new fuel-gauge/charger driver for RN5T618/RN5T619
- new charger driver for BQ25980, BQ25975 and BQ25960
- bq27xxx-battery: add support for TI bq34z100
- gpio-charger: convert to GPIO descriptors
- gpio-charger: add optional support for charge current limiting
- max17040: add support for max17041, max17043, max17044
- max17040: add support for max17048, max17049, max17058, max17059
- smb347-charger: add DT support
- smb247-charger: add SMB345 and SMB358 support
- simple-battery: add temperature properties
- lots of minor fixes, cleanups and DT binding YAML conversions
Reset drivers:
- ocelot: Add support for Sparx5"
* tag 'for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (81 commits)
power: reset: POWER_RESET_OCELOT_RESET should depend on Ocelot or Sparx5
power: supply: bq25980: Fix uninitialized wd_reg_val and overrun
power: supply: ltc2941: Fix ptr to enum cast
power: supply: test-power: revise parameter printing to use sprintf
power: supply: charger-manager: fix incorrect check on charging_duration_ms
power: supply: max17040: Fix ptr to enum cast
power: supply: bq25980: Fix uninitialized wd_reg_val
power: supply: bq25980: remove redundant zero check on ret
power: reset: ocelot: Add support for Sparx5
dt-bindings: reset: ocelot: Add Sparx5 support
power: supply: sbs-battery: keep error code when get_property() fails
power: supply: bq25980: Add support for the BQ259xx family
dt-binding: bq25980: Add the bq25980 flash charger
power: supply: fix spelling mistake "unprecise" -> "imprecise"
power: supply: test_power: add missing newlines when printing parameters by sysfs
power: supply: pm2301: drop duplicated i2c_device_id
power: supply: charger-manager: drop unused charger assignment
power: supply: rt9455: skip 'struct acpi_device_id' when !CONFIG_ACPI
power: supply: goldfish: skip 'struct acpi_device_id' when !CONFIG_ACPI
power: supply: bq25890: skip 'struct acpi_device_id' when !CONFIG_ACPI
...
The amount of changes is smaller at this round (what a surprise),
but lots of activity is seen. Most of changes are about ASoC
driver development, especially Intel platforms.
Here are some highlights:
General:
* Replace all tasklet usages with other alternatives
* Cleanup of the ASoC error unwinding code
* Fixes for trivial issues caught by static checker
* Spell fixes allover the places
ALSA Core:
* Lockdep fix for control devices
* Fix for potential OSS sequencer mutex stalls
HD-audio and USB-audio:
* SoundBlaster AE-7 support
* Changes in quirk table for the rename handling
* Quirks for HP and ASUS machines, Pioneer DJ DJM-250MK2.
ASoC:
* Lots of updates for Intel SOF and SoundWire enablement
* Replacement of the DSP driver for some older x86 systems;
the new code was written from scratch, better maintenance
expected
* Helpers for parsing auxiluary devices from the device tree
* New support for AllWinner A64, Cirrus Logic CS4234, Mediatek
MT6359 Microchip S/PDIF TX and RX controllers, Realtek RT1015P,
and Texas Instruments J721E, TAS2110, TAS2564 and TAS2764
-----BEGIN PGP SIGNATURE-----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=nWAp
-----END PGP SIGNATURE-----
Merge tag 'sound-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The amount of changes is smaller at this round (what a surprise), but
lots of activity is seen. Most of changes are about ASoC driver
development, especially Intel platforms. Here are some highlights:
General:
- Replace all tasklet usages with other alternatives
- Cleanup of the ASoC error unwinding code
- Fixes for trivial issues caught by static checker
- Spell fixes allover the places
ALSA Core:
- Lockdep fix for control devices
- Fix for potential OSS sequencer mutex stalls
HD-audio and USB-audio:
- SoundBlaster AE-7 support
- Changes in quirk table for the rename handling
- Quirks for HP and ASUS machines, Pioneer DJ DJM-250MK2.
ASoC:
- Lots of updates for Intel SOF and SoundWire enablement
- Replacement of the DSP driver for some older x86 systems; the new
code was written from scratch, better maintenance expected
- Helpers for parsing auxiluary devices from the device tree
- New support for AllWinner A64, Cirrus Logic CS4234, Mediatek MT6359
Microchip S/PDIF TX and RX controllers, Realtek RT1015P, and Texas
Instruments J721E, TAS2110, TAS2564 and TAS2764"
* tag 'sound-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (498 commits)
ALSA: hda/hdmi: fix incorrect locking in hdmi_pcm_close
ALSA: hda: fix jack detection with Realtek codecs when in D3
ALSA: fireworks: use semicolons rather than commas to separate statements
ALSA: hda: use semicolons rather than commas to separate statements
ALSA: hda/i915 - fix list corruption with concurrent probes
ASoC: dmaengine: Document support for TX only or RX only streams
ASoC: mchp-spdiftx: remove 'TX' from playback stream name
ASoC: ti: davinci-mcasp: Use &pdev->dev for early dev_warn
ASoC: tas2764: Add the driver for the TAS2764
dt-bindings: tas2764: Add the TAS2764 binding doc
ASoC: Intel: catpt: Add explicit DMADEVICES kconfig dependency
ASoC: Intel: catpt: Fix compilation when CONFIG_MODULES is disabled
ASoC: stm32: dfsdm: add actual resolution trace
ASoC: stm32: dfsdm: change rate limits
ASoC: qcom: sc7180: Add support for audio over DP
Asoc: qcom: lpass-platform : Increase buffer size
ASoC: qcom: Add support for lpass hdmi driver
Asoc: qcom: lpass:Update lpaif_dmactl members order
Asoc:qcom:lpass-cpu:Update dts property read API
ASoC: dt-bindings: Add dt binding for lpass hdmi
...
Here is the big set of char, misc, and other assorted driver subsystem
patches for 5.10-rc1.
There's a lot of different things in here, all over the drivers/
directory. Some summaries:
- soundwire driver updates
- habanalabs driver updates
- extcon driver updates
- nitro_enclaves new driver
- fsl-mc driver and core updates
- mhi core and bus updates
- nvmem driver updates
- eeprom driver updates
- binder driver updates and fixes
- vbox minor bugfixes
- fsi driver updates
- w1 driver updates
- coresight driver updates
- interconnect driver updates
- misc driver updates
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4g8YQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yngKgCeNpArCP/9vQJRK9upnDm8ZLunSCUAn1wUT/2A
/bTQ42c/WRQ+LU828GSM
=6sO2
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char, misc, and other assorted driver subsystem
patches for 5.10-rc1.
There's a lot of different things in here, all over the drivers/
directory. Some summaries:
- soundwire driver updates
- habanalabs driver updates
- extcon driver updates
- nitro_enclaves new driver
- fsl-mc driver and core updates
- mhi core and bus updates
- nvmem driver updates
- eeprom driver updates
- binder driver updates and fixes
- vbox minor bugfixes
- fsi driver updates
- w1 driver updates
- coresight driver updates
- interconnect driver updates
- misc driver updates
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (396 commits)
binder: fix UAF when releasing todo list
docs: w1: w1_therm: Fix broken xref, mistakes, clarify text
misc: Kconfig: fix a HISI_HIKEY_USB dependency
LSM: Fix type of id parameter in kernel_post_load_data prototype
misc: Kconfig: add a new dependency for HISI_HIKEY_USB
firmware_loader: fix a kernel-doc markup
w1: w1_therm: make w1_poll_completion static
binder: simplify the return expression of binder_mmap
test_firmware: Test partial read support
firmware: Add request_partial_firmware_into_buf()
firmware: Store opt_flags in fw_priv
fs/kernel_file_read: Add "offset" arg for partial reads
IMA: Add support for file reads without contents
LSM: Add "contents" flag to kernel_read_file hook
module: Call security_kernel_post_load_data()
firmware_loader: Use security_post_load_data()
LSM: Introduce kernel_post_load_data() hook
fs/kernel_read_file: Add file_size output argument
fs/kernel_read_file: Switch buffer size arg to size_t
fs/kernel_read_file: Remove redundant size argument
...
Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get
wrong, as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception of
the last "obviously correct" patch that updated a FALLTHROUGH comment
that got merged last weekend.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
Y7F+o2p8DiuLLQamdEyB
=lHr1
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
Core changes:
- NONE whatsoever, we don't even touch the core files this
time around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and
groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile
drivers.
- The "SH-PFC" (literally SuperH pin function controller, I
think) subdirectory is now renamed to the more neutral
"renesas", as these are not very much centered around
SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver.
-----BEGIN PGP SIGNATURE-----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=TdjX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- NONE whatsoever, we don't even touch the core files this time
around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile drivers.
- The "SH-PFC" (literally SuperH pin function controller, I think)
subdirectory is now renamed to the more neutral "renesas", as these
are not very much centered around SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver"
* tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (78 commits)
pinctrl: amd: Add missing pins to the pin group list
dt-bindings: pinctrl: sunxi: Allow pinctrl with more interrupt banks
pinctrl: visconti: PINCTRL_TMPV7700 should depend on ARCH_VISCONTI
pinctrl: mediatek: Free eint data on failure
pinctrl: single: fix debug output when #pinctrl-cells = 2
pinctrl: single: fix pinctrl_spec.args_count bounds check
pinctrl: sunrisepoint: Modify COMMUNITY macros to be consistent
pinctrl: cannonlake: Modify COMMUNITY macros to be consistent
pinctrl: tigerlake: Fix register offsets for TGL-H variant
pinctrl: Document pinctrl-single,pins when #pinctrl-cells = 2
pinctrl: mediatek: use devm_platform_ioremap_resource_byname()
pinctrl: nuvoton: npcm7xx: Constify static ops structs
pinctrl: mediatek: mt7622: add antsel pins/groups
pinctrl: ocelot: simplify the return expression of ocelot_gpiochip_register()
pinctrl: at91-pio4: add support for sama7g5 SoC
dt-bindings: pinctrl: at91-pio4: add microchip,sama7g5
pinctrl: spear: simplify the return expression of tvc_connect()
pinctrl: spear: simplify the return expression of spear310_pinctrl_probe
pinctrl: sprd: use module_platform_driver to simplify the code
pinctrl: Ingenic: Add I2S pins support for Ingenic SoCs.
...
Including:
- ARM-SMMU Updates from Will:
- Continued SVM enablement, where page-table is shared with
CPU
- Groundwork to support integrated SMMU with Adreno GPU
- Allow disabling of MSI-based polling on the kernel
command-line
- Minor driver fixes and cleanups (octal permissions, error
messages, ...)
- Secure Nested Paging Support for AMD IOMMU. The IOMMU will
fault when a device tries DMA on memory owned by a guest. This
needs new fault-types as well as a rewrite of the IOMMU memory
semaphore for command completions.
- Allow broken Intel IOMMUs (wrong address widths reported) to
still be used for interrupt remapping.
- IOMMU UAPI updates for supporting vSVA, where the IOMMU can
access address spaces of processes running in a VM.
- Support for the MT8167 IOMMU in the Mediatek IOMMU driver.
- Device-tree updates for the Renesas driver to support r8a7742.
- Several smaller fixes and cleanups all over the place.
-----BEGIN PGP SIGNATURE-----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=C0Sg
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- ARM-SMMU Updates from Will:
- Continued SVM enablement, where page-table is shared with CPU
- Groundwork to support integrated SMMU with Adreno GPU
- Allow disabling of MSI-based polling on the kernel command-line
- Minor driver fixes and cleanups (octal permissions, error
messages, ...)
- Secure Nested Paging Support for AMD IOMMU. The IOMMU will fault when
a device tries DMA on memory owned by a guest. This needs new
fault-types as well as a rewrite of the IOMMU memory semaphore for
command completions.
- Allow broken Intel IOMMUs (wrong address widths reported) to still be
used for interrupt remapping.
- IOMMU UAPI updates for supporting vSVA, where the IOMMU can access
address spaces of processes running in a VM.
- Support for the MT8167 IOMMU in the Mediatek IOMMU driver.
- Device-tree updates for the Renesas driver to support r8a7742.
- Several smaller fixes and cleanups all over the place.
* tag 'iommu-updates-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (57 commits)
iommu/vt-d: Gracefully handle DMAR units with no supported address widths
iommu/vt-d: Check UAPI data processed by IOMMU core
iommu/uapi: Handle data and argsz filled by users
iommu/uapi: Rename uapi functions
iommu/uapi: Use named union for user data
iommu/uapi: Add argsz for user filled data
docs: IOMMU user API
iommu/qcom: add missing put_device() call in qcom_iommu_of_xlate()
iommu/arm-smmu-v3: Add SVA device feature
iommu/arm-smmu-v3: Check for SVA features
iommu/arm-smmu-v3: Seize private ASID
iommu/arm-smmu-v3: Share process page tables
iommu/arm-smmu-v3: Move definitions to a header
iommu/io-pgtable-arm: Move some definitions to a header
iommu/arm-smmu-v3: Ensure queue is read after updating prod pointer
iommu/amd: Re-purpose Exclusion range registers to support SNP CWWB
iommu/amd: Add support for RMP_PAGE_FAULT and RMP_HW_ERR
iommu/amd: Use 4K page for completion wait write-back semaphore
iommu/tegra-smmu: Allow to group clients in same swgroup
iommu/tegra-smmu: Fix iova->phys translation
...
Add device tree bindings for display clock controller for
Qualcomm Technology Inc's SM8150 and SM8250 SoCs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Link: https://lore.kernel.org/r/20200927190653.13876-2-jonathan@marek.ca
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add device tree bindings for video clock controller for SM8250 SoCs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200923160635.28370-4-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add device tree bindings for video clock controller for SM8150 SoCs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200923160635.28370-3-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This change adds GDSCs, resets and most of the missing
clocks to the msm8994 GCC driver. The remaining ones
are of local_vote_clk and gate_clk type, which are not
yet supported upstream. Also reorder them to match the
original downstream driver.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20201005145855.149206-1-konradybcio@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This tag allows to build reset-imx7 as a module, and adds support to
reset the Cortex-M4 processor on i.MX8MQ to it, adds support for the
Versal platform to the reset-zynqmp driver, and fixes some kerneldoc
comments in the core and in sti/reset-syscfg.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCX2tCQxcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwNnQAQDnOhM1615HbwZ0YZM+jHC8U8+e
DfzXfsANHTffGJ4kZQEA1Z9uELtzsgQrrrtq3PaVVbYXGUcv2enMAO1AUD/0jwQ=
=zNMu
-----END PGP SIGNATURE-----
Merge tag 'reset-for-v5.10' of git://git.pengutronix.de/pza/linux into arm/drivers
Reset controller updates for v5.10
This tag allows to build reset-imx7 as a module, and adds support to
reset the Cortex-M4 processor on i.MX8MQ to it, adds support for the
Versal platform to the reset-zynqmp driver, and fixes some kerneldoc
comments in the core and in sti/reset-syscfg.
* tag 'reset-for-v5.10' of git://git.pengutronix.de/pza/linux:
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
Link: https://lore.kernel.org/r/2b77c90d2b970eb8fa09000b9ecb564bffa76374.camel@pengutronix.de
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix AM33XX_IOPAD macro that broke after recent pinctrl changes
to use #pinctrl-cells = 2. And fix omap_enter_idle_coupled()
for cases where cpu_cluster_pm_enter() returns an error as
otherwise we may end up wrongly idling the MPU domain on the
next WFI.
-----BEGIN PGP SIGNATURE-----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=sdtl
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.9/fixes-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Two regression fixes for omaps
Fix AM33XX_IOPAD macro that broke after recent pinctrl changes
to use #pinctrl-cells = 2. And fix omap_enter_idle_coupled()
for cases where cpu_cluster_pm_enter() returns an error as
otherwise we may end up wrongly idling the MPU domain on the
next WFI.
* tag 'omap-for-v5.9/fixes-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails
ARM: dts: am33xx: modify AM33XX_IOPAD for #pinctrl-cells = 2
Link: https://lore.kernel.org/r/pull-1601544624-617679@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
- Core:
- New PHY attribute for max_link_rate
- New phy drivers:
- Rockchip dphy driver moved from staging
- Socionext UniPhier AHCI PHY driver
- Intel LGM SoC USB phy
- Intel Keem Bay eMMC PHY driver
- Updates:
- Support for imx8mp usb phy
- Support for DP Phy and USB3+DP combo phy in QMP driver
- Support for Qualcomm sc7180 DP phy
- Support for cadence torrent PCIe and USB single linke and multilink
configurations along with USB, SGMII/QSGMII configurations
-----BEGIN PGP SIGNATURE-----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=U0WQ
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into usb-next
Vinod writes:
phy for 5.9
- Core:
- New PHY attribute for max_link_rate
- New phy drivers:
- Rockchip dphy driver moved from staging
- Socionext UniPhier AHCI PHY driver
- Intel LGM SoC USB phy
- Intel Keem Bay eMMC PHY driver
- Updates:
- Support for imx8mp usb phy
- Support for DP Phy and USB3+DP combo phy in QMP driver
- Support for Qualcomm sc7180 DP phy
- Support for cadence torrent PCIe and USB single linke and multilink
configurations along with USB, SGMII/QSGMII configurations
* tag 'phy-for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
phy: qcom-qmp: initialize the pointer to NULL
phy: qcom-qmp: Add support for sc7180 DP phy
phy: qcom-qmp: Add support for DP in USB3+DP combo phy
phy: qcom-qmp: Use devm_platform_ioremap_resource() to simplify
phy: qcom-qmp: Get dp_com I/O resource by index
phy: qcom-qmp: Move 'serdes' and 'cfg' into 'struct qcom_phy'
phy: qcom-qmp: Remove 'initialized' in favor of 'init_count'
phy: qcom-qmp: Move phy mode into struct qmp_phy
dt-bindings: phy: qcom,qmp-usb3-dp: Add DP phy information
dt-bindings: phy: ti,phy-j721e-wiz: fix bindings for torrent phy
dt-bindings: phy: cdns,torrent-phy: add reset-names
phy: rockchip-dphy-rx0: Include linux/delay.h
phy: fix USB_LGM_PHY warning & build errors
phy: cadence-torrent: Add USB + SGMII/QSGMII multilink configuration
phy: cadence-torrent: Add PCIe + USB multilink configuration
phy: cadence-torrent: Add single link USB register sequences
phy: cadence-torrent: Add single link SGMII/QSGMII register sequences
phy: cadence-torrent: Configure PHY_PLL_CFG as part of link_cmn_vals
phy: cadence-torrent: Add PHY link configuration sequences for single link
phy: cadence-torrent: Add clk changes for multilink configuration
...
There are 4 lanes in each J7200 SERDES. Each SERDES lane mux can
select upto 4 different IPs. Define all the possible functions.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Cc: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20200930122032.23481-2-rogerq@ti.com
- Add core support for the R-Car V3U (R8A779A0) SoC, including System
Controller (SYSC) and Reset (RST) support,
- Various Kconfig cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX2ShfwAKCRCKwlD9ZEnx
cO6bAP4kuetjBmf+BxLGRxZTEin+8YQRd7p051UZKBMa4qp2lwD+JKhnasH1qv64
CWS3LV8FNumj2Gr1e3YdJcgwb+9p3gc=
=K/tj
-----END PGP SIGNATURE-----
Merge tag 'renesas-drivers-for-v5.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/drivers
Renesas driver updates for v5.10 (take two)
- Add core support for the R-Car V3U (R8A779A0) SoC, including System
Controller (SYSC) and Reset (RST) support,
- Various Kconfig cleanups.
* tag 'renesas-drivers-for-v5.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
soc: renesas: r8a779a0-sysc: Add r8a779a0 support
soc: renesas: rcar-rst: Add support for R-Car V3U
soc: renesas: Identify R-Car V3U
soc: renesas: Sort driver description title
soc: renesas: Use ARM32/ARM64 for menu description
dt-bindings: clock: Add r8a779a0 CPG Core Clock Definitions
dt-bindings: power: Add r8a779a0 SYSC power domain definitions
Link: https://lore.kernel.org/r/20200918124800.15555-4-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
This set of changes fixes some minor issues in existing device trees and
adds ID EEPROMs on the Jetson Xavier NX. All ID EEPROMs are now labelled
to allow them to be detected by software.
It also adds support for the Tegra234 VDK board, which is a pre-silicon
platform for the upcoming Orin SoC.
-----BEGIN PGP SIGNATURE-----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=zeT7
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.10-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Changes for v5.10-rc1
This set of changes fixes some minor issues in existing device trees and
adds ID EEPROMs on the Jetson Xavier NX. All ID EEPROMs are now labelled
to allow them to be detected by software.
It also adds support for the Tegra234 VDK board, which is a pre-silicon
platform for the upcoming Orin SoC.
* tag 'tegra-for-5.10-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Initial Tegra234 VDK support
arm64: tegra: Populate EEPROMs for Jetson Xavier NX
arm64: tegra: Add label properties for EEPROMs
arm64: tegra: Add DT binding for AHUB components
arm64: tegra: Enable ACONNECT, ADMA and AGIC on Jetson Nano
arm64: tegra: Properly size register regions for GPU on Tegra194
arm64: tegra: Use valid PWM period for VDD_GPU on Tegra210
arm64: tegra: Describe display controller outputs for Tegra210
arm64: tegra: Disable SD card write-protection on Jetson Nano
arm64: tegra: Add VBUS supply for micro USB port on Jetson Nano
arm64: tegra: Wire up pinctrl states for all DPAUX controllers
arm64: tegra: Add ID EEPROMs on Jetson AGX Xavier
Link: https://lore.kernel.org/r/20200918150303.3938852-5-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the m4 reset used by the remoteproc driver
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Added documentation and Versal reset indices to describe
about Versal reset driver bindings.
In Versal all reset indices includes Class, SubClass, Type, Index
information whereas class refers to clock, reset, power etc.,
Underlying firmware in Versal have such classification and expects
the ID to be this way.
[13:0] - Index bits
[19:14] - Type bits
[25:20] - SubClass bits
[31:26] - Class bits.
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Modify the AM33XX_IOPAD macro so that it works now that #pinctrl-cells =
<2>. The third parameter is just a zero and the pinctrl-single driver
will just OR this with the second parameter so it has no actual effect.
There are no longer any dts files using this macro (following my patch
to am335x-guardian.dts), but this will keep dts files not in mainline
from breaking.
Fixes: 27c90e5e48 ("ARM: dts: am33xx-l4: change #pinctrl-cells from 1 to 2")
Suggested-by: Tony Lindgren <tony@atomide.com>
Reported-by: Trent Piepho <tpiepho@gmail.com>
Link: https://lore.kernel.org/linux-devicetree/20200921064707.GN7101@atomide.com/
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We intend to use one header file for SERDES MUX for all
TI SoCs so rename the header file.
The exsting macros are too generic. Prefix them with SoC name.
While at that, add the missing configurations for completeness.
Fixes: b766e3b0d5 ("arm64: dts: ti: k3-j721e-main: Add system controller node and SERDES lane mux")
Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20200918165930.2031-1-rogerq@ti.com
This add the bindings of the Power Controller found in the Amlogic AXG SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200917064702.1459-2-narmstrong@baylibre.com
The NVIDIA Tegra234 VDK is a simulation platform for the Orin SoC. It
supports a subset of the peripherals that will be available in the final
chip and serves as a bootstrapping platform.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Summit SMB3xx series is a Programmable Switching Li+ Battery Charger.
This patch adds device-tree binding for Summit SMB345, SMB347 and SMB358
chargers.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds IOMMU binding documentation and larb port definitions
for the MT8167 SoC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200907101649.1573134-1-fparent@baylibre.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
q6afe exposes various lpass clocks controls via q6dsp q6afe commands.
This patch adds bindings required for this clock controller.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200910135708.14842-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add clock ID definitions for the CPU parent clocks for SoCs
which don't have such definitions yet. This will allow us to
reference the parent clocks directly by cached struct clk_hw
pointers in the clock provider, rather than doing clk lookup
by name.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200826171529.23618-1-s.nawrocki@samsung.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch adds ID for the mout_sw_aclk_g3d (SW_CLKMUX_ACLK_G3D) clock,
mostly for internal use in the CMU driver. It will allow to avoid the
__clk_lookup() call when setting up the clock during the clock provider
initialization.
Link: https://lore.kernel.org/r/20200811151251.31613-1-s.nawrocki@samsung.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
New LPASS supports various codec macros, DSP firmware already
has support to those ports. Add corresponding configuration
support to those ports in adsp drivers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200910101732.23484-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add generic qcom interconnect bindings that are common across platforms. In
particular, these include QCOM_ICC_TAG_* macros that clients can use when
calling icc_set_tag().
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200903192149.30385-3-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The Qualcomm SM8250 platform has several bus fabrics that could be
controlled and tuned dynamically according to the bandwidth demand.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200728023811.5607-4-jonathan@marek.ca
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The Qualcomm SM8150 platform has several bus fabrics that could be
controlled and tuned dynamically according to the bandwidth demand.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200728023811.5607-3-jonathan@marek.ca
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
The root clock slice at 0xbf00 is media_ldb clock,
not csi_phy2_ref, so correct it.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Summit SMB3xx series is a Programmable Switching Li+ Battery Charger.
This patch adds device-tree binding for Summit SMB345, SMB347 and SMB358
chargers.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add the clock for CRC block allowing it to be enabled by consumers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The firmware running on the RPi VideoCore can be used to reset and
initialize HW controlled by the firmware.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-2-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BCM6318 SoCs have a power domain controller to enable/disable certain
components in order to save power.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <F.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63268 SoCs have a power domain controller to enable/disable certain
components in order to save power.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <F.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM6362 SoCs have a power domain controller to enable/disable certain
components in order to save power.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <F.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM6328 SoCs have a power domain controller to enable/disable certain
components in order to save power.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Florian Fainelli <F.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add header defining dai-id and mclk id for SC7180 lpass soc.
Signed-off-by: Ajit Pandey <ajitp@codeaurora.org>
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1597402388-14112-9-git-send-email-rohitkr@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
happened to tag the tree at an earlier point in the history of clk-next.
I must have fat fingered it and checked out an older version of clk-next
on this second computer I'm using.
This time it actually includes more code for Qualcomm SoCs, the AT91
major updates, and some Rockchip SoC clk driver updates as well. I've
corrected this flow so this shouldn't happen again.
-----BEGIN PGP SIGNATURE-----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=/8EM
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk updates from Stephen Boyd:
"Here's some more updates that missed the last pull request because I
happened to tag the tree at an earlier point in the history of
clk-next. I must have fat fingered it and checked out an older version
of clk-next on this second computer I'm using.
This time it actually includes more code for Qualcomm SoCs, the AT91
major updates, and some Rockchip SoC clk driver updates as well. I've
corrected this flow so this shouldn't happen again"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (83 commits)
clk: bcm2835: Do not use prediv with bcm2711's PLLs
clk: drop unused function __clk_get_flags
clk: hsdk: Fix bad dependency on IOMEM
dt-bindings: clock: Fix YAML schemas for LPASS clocks on SC7180
clk: mmp: avoid missing prototype warning
clk: sparx5: Add Sparx5 SoC DPLL clock driver
dt-bindings: clock: sparx5: Add bindings include file
clk: qoriq: add LS1021A core pll mux options
clk: clk-atlas6: fix return value check in atlas6_clk_init()
clk: tegra: pll: Improve PLLM enable-state detection
clk: X1000: Add support for calculat REFCLK of USB PHY.
clk: JZ4780: Reformat the code to align it.
clk: JZ4780: Add functions for enable and disable USB PHY.
clk: Ingenic: Add RTC related clocks for Ingenic SoCs.
dt-bindings: clock: Add tabs to align code.
dt-bindings: clock: Add RTC related clocks for Ingenic SoCs.
clk: davinci: Use fallthrough pseudo-keyword
clk: imx: Use fallthrough pseudo-keyword
clk: qcom: gcc-sdm660: Fix up gcc_mss_mnoc_bimc_axi_clk
clk: qcom: gcc-sdm660: Add missing modem reset
...
Including:
- Removal of the dev->archdata.iommu (or similar) pointers from
most architectures. Only Sparc is left, but this is private to
Sparc as their drivers don't use the IOMMU-API.
- ARM-SMMU Updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell
Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d Updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel
drivers into their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test
coverage)
-----BEGIN PGP SIGNATURE-----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=3O2Z
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Remove of the dev->archdata.iommu (or similar) pointers from most
architectures. Only Sparc is left, but this is private to Sparc as
their drivers don't use the IOMMU-API.
- ARM-SMMU updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel drivers into
their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test coverage)
* tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (77 commits)
iommu/amd: Move Kconfig and Makefile bits down into amd directory
iommu/vt-d: Move Kconfig and Makefile bits down into intel directory
iommu/arm-smmu: Move Arm SMMU drivers into their own subdirectory
iommu/vt-d: Skip TE disabling on quirky gfx dedicated iommu
iommu: Add gfp parameter to io_pgtable_ops->map()
iommu: Mark __iommu_map_sg() as static
iommu/vt-d: Rename intel-pasid.h to pasid.h
iommu/vt-d: Add page response ops support
iommu/vt-d: Report page request faults for guest SVA
iommu/vt-d: Add a helper to get svm and sdev for pasid
iommu/vt-d: Refactor device_to_iommu() helper
iommu/vt-d: Disable multiple GPASID-dev bind
iommu/vt-d: Warn on out-of-range invalidation address
iommu/vt-d: Fix devTLB flush for vSVA
iommu/vt-d: Handle non-page aligned address
iommu/vt-d: Fix PASID devTLB invalidation
iommu/vt-d: Remove global page support in devTLB flush
iommu/vt-d: Enforce PASID devTLB field mask
iommu: Make some functions static
iommu/amd: Remove double zero check
...
kernel series:
Core changes:
- The GPIO patch "gpiolib: Introduce
for_each_requested_gpio_in_range() macro" was put in an
immutable branch and merged into the pinctrl tree as well.
We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among
other things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have
been modularized. This is driven by the Google Android
GKI initiative I think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
-----BEGIN PGP SIGNATURE-----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=mJgb
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of the pin control changes for the v5.9 kernel
series:
Core changes:
- The GPIO patch "gpiolib: Introduce for_each_requested_gpio_in_range()
macro" was put in an immutable branch and merged into the pinctrl
tree as well. We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among other
things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have been
modularized. This is driven by the Google Android GKI initiative I
think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
* tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC
pinctrl: stmfx: Use irqchip template
pinctrl: amd: Use irqchip template
pinctrl: mediatek: fix build for tristate changes
pinctrl: samsung: Use bank name as irqchip name
pinctrl: core: print gpio in pins debugfs file
pinctrl: mediatek: add mt6779 eint support
pinctrl: mediatek: add pinctrl support for MT6779 SoC
pinctrl: mediatek: avoid virtual gpio trying to set reg
pinctrl: mediatek: update pinmux definitions for mt6779
pinctrl: stm32: use the hwspin_lock_timeout_in_atomic() API
pinctrl: mcp23s08: Use irqchip template
pinctrl: sx150x: Use irqchip template
dt-bindings: ingenic,pinctrl: Support pinmux/pinconf nodes
pinctrl: intel: Add Intel Emmitsburg pin controller support
pinctl: ti: iodelay: Replace HTTP links with HTTPS ones
Revert "gpio: omap: handle pin config bias flags"
pinctrl: single: Use fallthrough pseudo-keyword
pinctrl: qcom: spmi-gpio: Use fallthrough pseudo-keyword
pinctrl: baytrail: Use fallthrough pseudo-keyword
...
framework we just have some minor tweaks and a debugfs feature, so not much to
see there. The driver updates are fairly well split between AT91 and Qualcomm
clk support. Adding those two drivers together equals about 50% of the
diffstat. Otherwise, the big amount of work this time was on supporting
Broadcom's Raspberry Pi firmware clks. See below for some more highlights.
Core:
- Document clk_hw_round_rate() so it gets some more use
- Remove unused __clk_get_flags()
- Add a prepare/enable debugfs feature similar to rate setting
New Drivers:
- Add support for SAMA7G5 SoC clks
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Microchip Sparx5 DPLL clk
- Add support for the new Renesas RZ/G2H (R8A774E1) SoC
Updates:
- Make defines for bcm63xx-gate clks to use in DT
- Support BCM2711 SoC firmware clks
- Add HDMI clks for BCM2711 SoCs
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
- Support gate clks on BCM6318 SoCs
- RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
- Use poll_timeout functions in Rockchip clk driver
- Support Rockchip rk3288w SoC variant
- Mark mac_lbtest critical on Rockchip rk3188
- Add CAAM clock support for i.MX vf610 driver
- Add MU root clock support for i.MX imx8mp driver
- Amlogic g12: add neural network accelerator clock sources
- Amlogic meson8: remove critical flag for main PLL divider
- Amlogic meson8: add video decoder clock gates
- Convert one more Renesas DT binding to json-schema
- Enhance critical clock handling on Renesas platforms to only consider
clocks that were enabled at boot time
-----BEGIN PGP SIGNATURE-----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=QLRg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"It looks like a smaller batch of clk updates this time around.
In the core framework we just have some minor tweaks and a debugfs
feature, so not much to see there. The driver updates are fairly well
split between AT91 and Qualcomm clk support. Adding those two drivers
together equals about 50% of the diffstat.
Otherwise, the big amount of work this time was on supporting
Broadcom's Raspberry Pi firmware clks.
Highlights:
Core:
- Document clk_hw_round_rate() so it gets some more use
- Remove unused __clk_get_flags()
- Add a prepare/enable debugfs feature similar to rate setting
New Drivers:
- Add support for SAMA7G5 SoC clks
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Microchip Sparx5 DPLL clk
- Add support for the new Renesas RZ/G2H (R8A774E1) SoC
Updates:
- Make defines for bcm63xx-gate clks to use in DT
- Support BCM2711 SoC firmware clks
- Add HDMI clks for BCM2711 SoCs
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
- Support gate clks on BCM6318 SoCs
- RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
- Use poll_timeout functions in Rockchip clk driver
- Support Rockchip rk3288w SoC variant
- Mark mac_lbtest critical on Rockchip rk3188
- Add CAAM clock support for i.MX vf610 driver
- Add MU root clock support for i.MX imx8mp driver
- Amlogic g12: add neural network accelerator clock sources
- Amlogic meson8: remove critical flag for main PLL divider
- Amlogic meson8: add video decoder clock gates
- Convert one more Renesas DT binding to json-schema
- Enhance critical clock handling on Renesas platforms to only
consider clocks that were enabled at boot time"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (79 commits)
clk: qcom: gcc: Make disp gpll0 branch aon for sc7180/sdm845
ipq806x: gcc: add support for child probe
clk: qcom: msm8996: Make symbol 'cpu_msm8996_clks' static
clk: qcom: ipq8074: Add correct index for PCIe clocks
clk: <linux/clk-provider.h>: drop a duplicated word
clk: renesas: cpg-mssr: Add r8a774e1 support
dt-bindings: clock: renesas,cpg-mssr: Document r8a774e1
clk: Drop duplicate selection in Kconfig
clk: qcom: smd: Add support for MSM8992/4 rpm clocks
clk: qcom: ipq8074: Add missing clocks for pcie
dt-bindings: clock: qcom: ipq8074: Add missing bindings for PCIe
Replace HTTP links with HTTPS ones: Common CLK framework
clk: qcom: Add CPU clock driver for msm8996
dt-bindings: clk: qcom: Add bindings for CPU clock for msm8996
soc: qcom: Separate kryo l2 accessors from PMU driver
clk: meson: meson8b: add the vclk2_en gate clock
clk: meson: meson8b: add the vclk_en gate clock
clk: qcom: Fix return value check in apss_ipq6018_probe()
clk: bcm: dvp: Add missing module informations
clk: meson: meson8b: Drop CLK_IS_CRITICAL from fclk_div2
...
Here is the large set of Staging and IIO driver patches for 5.9-rc1.
Lots of churn here, but overall the size increase in lines added is
small, while adding a load of new IIO drivers.
Major things in here:
- lots and lots of IIO new drivers and frameworks added
- IIO driver fixes and updates
- lots of tiny coding style cleanups for staging drivers
- vc04_services major reworks and cleanups
We had 3 set of drivers move out of staging in this round as well:
- wilc1000 wireless driver moved out of staging
- speakup moved out of staging
- most USB driver moved out of staging
Full details are in the shortlog.
All of these have been in linux-next with no reported issues. The last
few changes here were to resolve reported linux-next issues, and they
seem to have resolved the problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXyv2rA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yngIgCfZOVj022X+paV81NwvO/TroMDA7oAn1C4XCmY
Fxz55oHIyk9lbQxsDhID
=ujqG
-----END PGP SIGNATURE-----
Merge tag 'staging-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the large set of Staging and IIO driver patches for 5.9-rc1.
Lots of churn here, but overall the size increase in lines added is
small, while adding a load of new IIO drivers.
Major things in here:
- lots and lots of IIO new drivers and frameworks added
- IIO driver fixes and updates
- lots of tiny coding style cleanups for staging drivers
- vc04_services major reworks and cleanups
We had 3 set of drivers move out of staging in this round as well:
- wilc1000 wireless driver moved out of staging
- speakup moved out of staging
- most USB driver moved out of staging
Full details are in the shortlog.
All of these have been in linux-next with no reported issues. The last
few changes here were to resolve reported linux-next issues, and they
seem to have resolved the problems"
* tag 'staging-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (428 commits)
staging: most: fix up movement of USB driver
staging: rts5208: clear alignment style issues
staging: r8188eu: replace rtw_netdev_priv define with inline function
staging: netlogic: clear alignment style issues
staging: android: ashmem: Fix lockdep warning for write operation
drivers: most: add USB adapter driver
staging: most: Use %pM format specifier for MAC addresses
staging: ks7010: Use %pM format specifier for MAC addresses
staging: qlge: qlge_dbg: removed comment repition
staging: wfx: Use flex_array_size() helper in memcpy()
staging: rtl8723bs: Align macro definitions
staging: rtl8723bs: Clean up function declations
staging: rtl8723bs: Fix coding style errors
drivers: staging: audio: Fix the missing header file for helper file
staging: greybus: audio: Enable GB codec, audio module compilation.
staging: greybus: audio: Add helper APIs for dynamic audio modules
staging: greybus: audio: Resolve compilation error in topology parser
staging: greybus: audio: Resolve compilation errors for GB codec module
staging: greybus: audio: Maintain jack list within GB Audio module
staging: greybus: audio: Update snd_jack FW usage as per new APIs
...
This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
* API cleanups and conversions to the unified mute_stream() call
* Simplify I/O helper functions
* Use helper macros to retrieve RTD from substreams
ASoC drivers:
* Lots of fixes and cleanups in Intel ASoC drivers
* Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
* Minor code refacotring for SG-buffer handling
HD-audio:
* Generalization of mute-LED handling with LED classdev
* Intel silent stream support for HDMI
* Device-specific fixes: CA0132, Loongson-3
Others:
* Usual USB- and HD-audio quirks for various devices
* Fixes for echoaudio DMA position handling
* Various documents and trivial fixes for sparse warnings
* Conversion to adapt inclusive terms
-----BEGIN PGP SIGNATURE-----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=sy7n
-----END PGP SIGNATURE-----
Merge tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
- API cleanups and conversions to the unified mute_stream() call
- Simplify I/O helper functions
- Use helper macros to retrieve RTD from substreams
ASoC drivers:
- Lots of fixes and cleanups in Intel ASoC drivers
- Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
- Minor code refacotring for SG-buffer handling
HD-audio:
- Generalization of mute-LED handling with LED classdev
- Intel silent stream support for HDMI
- Device-specific fixes: CA0132, Loongson-3
Others:
- Usual USB- and HD-audio quirks for various devices
- Fixes for echoaudio DMA position handling
- Various documents and trivial fixes for sparse warnings
- Conversion to adopt inclusive terms"
* tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (479 commits)
ALSA: pci: delete repeated words in comments
ALSA: isa: delete repeated words in comments
ALSA: hda/tegra: Add 100us dma stop delay
ALSA: hda: Add dma stop delay variable
ASoC: hda/tegra: Set buffer alignment to 128 bytes
ALSA: seq: oss: Serialize ioctls
ALSA: hda/hdmi: Add quirk to force connectivity
ALSA: usb-audio: add startech usb audio dock name
ALSA: usb-audio: Add support for Lenovo ThinkStation P620
Revert "ALSA: hda: call runtime_allow() for all hda controllers"
ALSA: hda/ca0132 - Fix AE-5 microphone selection commands.
ALSA: hda/ca0132 - Add new quirk ID for Recon3D.
ALSA: hda/ca0132 - Fix ZxR Headphone gain control get value.
ALSA: hda/realtek: Add alc269/alc662 pin-tables for Loongson-3 laptops
ALSA: docs: fix typo
ALSA: doc: use correct config variable name
ASoC: core: Two step component registration
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: sh: Replace 'select' DMADEVICES 'with depends on'
...
core:
- add user def flag to cmd line modes
- dma_fence_wait added might_sleep
- dma-fence lockdep annotations
- indefinite fences are bad documentation
- gem CMA functions used in more drivers
- struct mutex removal
- more drm_ debug macro usage
- set/drop master api fixes
- fix for drm/mm hole size comparison
- drm/mm remove invalid entry optimization
- optimise drm/mm hole handling
- VRR debugfs added
- uncompressed AFBC modifier support
- multiple display id blocks in EDID
- multiple driver sg handling fixes
- __drm_atomic_helper_crtc_reset in all drivers
- managed vram helpers
ttm:
- ttm_mem_reg handling cleanup
- remove bo offset field
- drop CMA memtype flag
- drop mappable flag
xilinx:
- New Xilinx ZynqMP DisplayPort Subsystem driver
nouveau:
- add CRC support
- start using NVIDIA published class header files
- convert all push buffer emission to new macros
- Proper push buffer space management for EVO/NVD channels.
- firmware loading fixes
- 2MiB system memory pages support on Pascal and newer
vkms:
- larget cursor support
i915:
- Rocketlake platform enablement
- Early DG1 enablement
- Numerous GEM refactorings
- DP MST fixes
- FBC, PSR, Cursor, Color, Gamma fixes
- TGL, RKL, EHL workaround updates
- TGL 8K display support fixes
- SDVO/HDMI/DVI fixes
amdgpu:
- Initial support for Sienna Cichlid GPU
- Initial support for Navy Flounder GPU
- SI UVD/VCE support
- expose rotation property
- Add support for unique id on Arcturus
- Enable runtime PM on vega10 boards that support BACO
- Skip BAR resizing if the bios already did id
- Major swSMU code cleanup
- Fixes for DCN bandwidth calculations
amdkfd:
- Track SDMA usage per process
- SMI events interface
radeon:
- Default to on chip GART for AGP boards on all arches
- Runtime PM reference count fixes
msm:
- headers regenerated causing churn
- a650/a640 display and GPU enablement
- dpu dither support for 6bpc panels
- dpu cursor fix
- dsi/mdp5 enablement for sdm630/sdm636/sdm66
tegra:
- video capture prep support
- reflection support
mediatek:
- convert mtk_dsi to bridge API
meson:
- FBC support
sun4i:
- iommu support
rockchip:
- register locking fix
- per-pixel alpha support PX30 VOP
-
mgag200:
- ported to simple and shmem helpers
- device init cleanups
- use managed pci functions
- dropped hw cursor support
ast:
- use managed pci functions
- use managed VRAM helpers
- rework cursor support
malidp:
- dev_groups support
hibmc:
- refactor hibmc_drv_vdac:
vc4:
- create TXP CRTC
imx:
- error path fixes and cleanups
etnaviv:
- clock handling and error handling cleanups
- use pin_user_pages
-----BEGIN PGP SIGNATURE-----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=Yvtd
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-08-06' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"New xilinx displayport driver, AMD support for two new GPUs (more
header files), i915 initial support for RocketLake and some work on
their DG1 (discrete chip).
The core also grew some lockdep annotations to try and constrain what
drivers do with dma-fences, and added some documentation on why the
idea of indefinite fences doesn't work.
The long list is below.
I do have some fixes trees outstanding, but I'll follow up with those
later.
core:
- add user def flag to cmd line modes
- dma_fence_wait added might_sleep
- dma-fence lockdep annotations
- indefinite fences are bad documentation
- gem CMA functions used in more drivers
- struct mutex removal
- more drm_ debug macro usage
- set/drop master api fixes
- fix for drm/mm hole size comparison
- drm/mm remove invalid entry optimization
- optimise drm/mm hole handling
- VRR debugfs added
- uncompressed AFBC modifier support
- multiple display id blocks in EDID
- multiple driver sg handling fixes
- __drm_atomic_helper_crtc_reset in all drivers
- managed vram helpers
ttm:
- ttm_mem_reg handling cleanup
- remove bo offset field
- drop CMA memtype flag
- drop mappable flag
xilinx:
- New Xilinx ZynqMP DisplayPort Subsystem driver
nouveau:
- add CRC support
- start using NVIDIA published class header files
- convert all push buffer emission to new macros
- Proper push buffer space management for EVO/NVD channels.
- firmware loading fixes
- 2MiB system memory pages support on Pascal and newer
vkms:
- larger cursor support
i915:
- Rocketlake platform enablement
- Early DG1 enablement
- Numerous GEM refactorings
- DP MST fixes
- FBC, PSR, Cursor, Color, Gamma fixes
- TGL, RKL, EHL workaround updates
- TGL 8K display support fixes
- SDVO/HDMI/DVI fixes
amdgpu:
- Initial support for Sienna Cichlid GPU
- Initial support for Navy Flounder GPU
- SI UVD/VCE support
- expose rotation property
- Add support for unique id on Arcturus
- Enable runtime PM on vega10 boards that support BACO
- Skip BAR resizing if the bios already did id
- Major swSMU code cleanup
- Fixes for DCN bandwidth calculations
amdkfd:
- Track SDMA usage per process
- SMI events interface
radeon:
- Default to on chip GART for AGP boards on all arches
- Runtime PM reference count fixes
msm:
- headers regenerated causing churn
- a650/a640 display and GPU enablement
- dpu dither support for 6bpc panels
- dpu cursor fix
- dsi/mdp5 enablement for sdm630/sdm636/sdm66
tegra:
- video capture prep support
- reflection support
mediatek:
- convert mtk_dsi to bridge API
meson:
- FBC support
sun4i:
- iommu support
rockchip:
- register locking fix
- per-pixel alpha support PX30 VOP
mgag200:
- ported to simple and shmem helpers
- device init cleanups
- use managed pci functions
- dropped hw cursor support
ast:
- use managed pci functions
- use managed VRAM helpers
- rework cursor support
malidp:
- dev_groups support
hibmc:
- refactor hibmc_drv_vdac:
vc4:
- create TXP CRTC
imx:
- error path fixes and cleanups
etnaviv:
- clock handling and error handling cleanups
- use pin_user_pages"
* tag 'drm-next-2020-08-06' of git://anongit.freedesktop.org/drm/drm: (1747 commits)
drm/msm: use kthread_create_worker instead of kthread_run
drm/msm/mdp5: Add MDP5 configuration for SDM636/660
drm/msm/dsi: Add DSI configuration for SDM660
drm/msm/mdp5: Add MDP5 configuration for SDM630
drm/msm/dsi: Add phy configuration for SDM630/636/660
drm/msm/a6xx: add A640/A650 hwcg
drm/msm/a6xx: hwcg tables in gpulist
drm/msm/dpu: add SM8250 to hw catalog
drm/msm/dpu: add SM8150 to hw catalog
drm/msm/dpu: intf timing path for displayport
drm/msm/dpu: set missing flush bits for INTF_2 and INTF_3
drm/msm/dpu: don't use INTF_INPUT_CTRL feature on sdm845
drm/msm/dpu: move some sspp caps to dpu_caps
drm/msm/dpu: update UBWC config for sm8150 and sm8250
drm/msm/dpu: use right setup_blend_config for sm8150 and sm8250
drm/msm/a6xx: set ubwc config for A640 and A650
drm/msm/adreno: un-open-code some packets
drm/msm: sync generated headers
drm/msm/a6xx: add build_bw_table for A640/A650
drm/msm/a6xx: fix crashstate capture for A650
...
Okay, so... this one is interesting. RGB LEDs are very common, and we
need to have some kind of support for them. Multicolor is for
arbitrary set of LEDs in one package, RGB is for LEDs that can produce
full range of colors. We do not have real multicolor LED that is not
RGB in the pipeline, so that one is disabled for now.
You can expect this saga to continue with next pull requests.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQRPfPO7r0eAhk010v0w5/Bqldv68gUCXyskqQAKCRAw5/Bqldv6
8ge0AJ9JRTa/0Xkl7JuKUpC93jAnvjpK+ACgsDijb77H5zmtwC8xa0kXiDsbh3E=
=aSJX
-----END PGP SIGNATURE-----
Merge tag 'leds-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Okay, so... this one is interesting. RGB LEDs are very common, and we
need to have some kind of support for them. Multicolor is for
arbitrary set of LEDs in one package, RGB is for LEDs that can produce
full range of colors. We do not have real multicolor LED that is not
RGB in the pipeline, so that one is disabled for now.
You can expect this saga to continue with next pull requests"
* tag 'leds-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds: (37 commits)
MAINTAINERS: Remove myself as LED subsystem maintainer
leds: disallow /sys/class/leds/*:multi:* for now
leds: add RGB color option, as that is different from multicolor.
Make LEDS_LP55XX_COMMON depend on I2C to fix build errors:
Documentation: ABI: leds-turris-omnia: document sysfs attribute
leds: initial support for Turris Omnia LEDs
dt-bindings: leds: add cznic,turris-omnia-leds binding
leds: pattern trigger -- check pattern for validity
leds: Replace HTTP links with HTTPS ones
leds: trigger: add support for LED-private device triggers
leds: lp5521: Add multicolor framework multicolor brightness support
leds: lp5523: Update the lp5523 code to add multicolor brightness function
leds: lp55xx: Add multicolor framework support to lp55xx
leds: lp55xx: Convert LED class registration to devm_*
dt-bindings: leds: Convert leds-lp55xx to yaml
leds: multicolor: Introduce a multicolor class definition
leds: Add multicolor ID to the color ID list
dt: bindings: Add multicolor class dt bindings documention
leds: lp5523: Fix various formatting issues in the code
leds: lp55xx: Fix file permissions to use DEVICE_ATTR macros
...
- Improve device links cycle detection and breaking. Add more
bindings for device link dependencies.
- Refactor parsing 'no-map' in __reserved_mem_alloc_size()
- Improve DT unittest 'ranges' and 'dma-ranges' test case to check
differing cell sizes
- Various http to https link conversions
- Add a schema check to prevent 'syscon' from being used by itself
without a more specific compatible
- A bunch more DT binding conversions to schema
-----BEGIN PGP SIGNATURE-----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=6f3o
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
- Improve device links cycle detection and breaking. Add more bindings
for device link dependencies.
- Refactor parsing 'no-map' in __reserved_mem_alloc_size()
- Improve DT unittest 'ranges' and 'dma-ranges' test case to check
differing cell sizes
- Various http to https link conversions
- Add a schema check to prevent 'syscon' from being used by itself
without a more specific compatible
- A bunch more DT binding conversions to schema
* tag 'devicetree-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
of: reserved-memory: remove duplicated call to of_get_flat_dt_prop() for no-map node
of: unittest: Use bigger address cells to catch parser regressions
dt-bindings: memory-controllers: Convert mmdc to json-schema
dt-bindings: mtd: Convert imx nand to json-schema
dt-bindings: mtd: Convert gpmi nand to json-schema
dt-bindings: iio: io-channel-mux: Fix compatible string in example code
of: property: Add device link support for pinctrl-0 through pinctrl-8
of: property: Add device link support for multiple DT bindings
dt-bindings: phy: ti: phy-gmii-sel: convert bindings to json-schema
dt-bindings: mux: mux.h: drop a duplicated word
dt-bindings: misc: Convert olpc,xo1.75-ec to json-schema
dt-bindings: aspeed-lpc: Replace HTTP links with HTTPS ones
dt-bindings: drm/bridge: Replace HTTP links with HTTPS ones
drm/tilcdc: Replace HTTP links with HTTPS ones
dt-bindings: iommu: renesas,ipmmu-vmsa: Add r8a774e1 support
dt-bindings: fpga: Replace HTTP links with HTTPS ones
dt-bindings: virtio: Replace HTTP links with HTTPS ones
dt-bindings: media: imx274: Add optional input clock and supplies
dt-bindings: i2c-gpio: Use 'deprecated' keyword on deprecated properties
dt-bindings: interrupt-controller: Fix typos in loongson,liointc.yaml
...
Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXylccQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymofgCfZ1CxNWd0ZVM0YIn8cY9gO6ON7MsAnRq48hvn
Vjf4rKM73GC11bVF4Gyy
=Xq1R
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char and misc and other driver subsystem
patches for 5.9-rc1. Lots of new driver submissions in here, and
cleanups and features for existing drivers.
Highlights are:
- habanalabs driver updates
- coresight driver updates
- nvmem driver updates
- huge number of "W=1" build warning cleanups from Lee Jones
- dyndbg updates
- virtbox driver fixes and updates
- soundwire driver updates
- mei driver updates
- phy driver updates
- fpga driver updates
- lots of smaller individual misc/char driver cleanups and fixes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (322 commits)
habanalabs: remove unused but set variable 'ctx_asid'
nvmem: qcom-spmi-sdam: Enable multiple devices
dt-bindings: nvmem: SID: add binding for A100's SID controller
nvmem: update Kconfig description
nvmem: qfprom: Add fuse blowing support
dt-bindings: nvmem: Add properties needed for blowing fuses
dt-bindings: nvmem: qfprom: Convert to yaml
nvmem: qfprom: use NVMEM_DEVID_AUTO for multiple instances
nvmem: core: add support to auto devid
nvmem: core: Add nvmem_cell_read_u8()
nvmem: core: Grammar fixes for help text
nvmem: sc27xx: add sc2730 efuse support
nvmem: Enforce nvmem stride in the sysfs interface
MAINTAINERS: Add git tree for NVMEM FRAMEWORK
nvmem: sprd: Fix return value of sprd_efuse_probe()
drivers: android: Fix the SPDX comment style
drivers: android: Fix a variable declaration coding style issue
drivers: android: Remove braces for a single statement if-else block
drivers: android: Remove the use of else after return
drivers: android: Fix a variable declaration coding style issue
...
- Prevent unnecessary timer softirq invocations by extending the tracking
of the next expiring timer in the timer wheel beyond the existing NOHZ
functionality. The tracking overhead at enqueue time is within the
noise, but on sensitive workloads the avoidance of the soft interrupt
invocation is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer chip
variants all over the driver space.
-----BEGIN PGP SIGNATURE-----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=uJnp
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Time, timers and related driver updates:
- Prevent unnecessary timer softirq invocations by extending the
tracking of the next expiring timer in the timer wheel beyond the
existing NOHZ functionality.
The tracking overhead at enqueue time is within the noise, but on
sensitive workloads the avoidance of the soft interrupt invocation
is a measurable improvement.
- The obligatory new clocksource driver for Ingenic X100 OST
- The usual fixes, improvements, cleanups and extensions for newer
chip variants all over the driver space"
* tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
timers: Recalculate next timer interrupt only when necessary
clocksource/drivers/ingenic: Add support for the Ingenic X1000 OST.
dt-bindings: timer: Add Ingenic X1000 OST bindings.
clocksource/drivers: Replace HTTP links with HTTPS ones
clocksource/drivers/nomadik-mtu: Handle 32kHz clock
clocksource/drivers/sh_cmt: Use "kHz" for kilohertz
clocksource/drivers/imx: Add support for i.MX TPM driver with ARM64
clocksource/drivers/ingenic: Add high resolution timer support for SMP/SMT.
timers: Lower base clock forwarding threshold
timers: Remove must_forward_clk
timers: Spare timer softirq until next expiry
timers: Expand clk forward logic beyond nohz
timers: Reuse next expiry cache after nohz exit
timers: Always keep track of next expiry
timers: Optimize _next_timer_interrupt() level iteration
timers: Add comments about calc_index() ceiling work
timers: Move trigger_dyntick_cpu() to enqueue_timer()
timers: Use only bucket expiry for base->next_expiry value
timers: Preserve higher bits of expiration on index calculation
clocksource/drivers/timer-atmel-tcb: Add sama5d2 support
...
Add documentation for the mt6779 gce.
Add gce header file defined the gce hardware event,
subsys number and constant for mt6779.
Signed-off-by: Dennis YC Hsieh <dennis-yc.hsieh@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This time around the bulk of the work on the regulator API has been
cleanups of various kinds, partly but not entirely inspired by the W=1
stuff that 0day turned on. There's also been a fairly large crop of new
drivers, and a few bugfixes for existing drivers.
- Mode setting support for MT6397 and DA9211.
- New drivers for ChromeOS embedded controllers, Fairchild FAN53880,
NXP PCA9450, Qualcomm LABIBB, MP5496, and VBUS booster, and Silergy
SY8827N
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl8n+tcTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AbDB/9d9/CX9OK0qy4qMew7t/+bmHNKWB4O
jlVSp6Raj9dF3siLCaWT70jKrCEKBUIMSiA6c6UqWGHPbHLvvsTuu1aau2APIi/w
PDrnAfcku7J6CJMl4wwkn1Sh8vobXtqeZbT0Ydfx7QRzI+AMqz7CWLrOh9ET3Z3S
lN85GT7lqiG1hD+frep1FzpZDorzZa4Xvml7/7ns51IRn9NezdjRFBTG1dsZuKy6
GPEFXgLCfhaYs7zY1Tk9l5sMAdG/1OU/OvT4w4xmo7PkEZGYAHLSJfHQdRu2LwZU
r9YSVJ+COOfqaoml08XbFx1U12zWHgln+5ty+EuLxNNl4taBPpLqZDBC
=JJHu
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This time around the bulk of the work on the regulator API has been
cleanups of various kinds, partly but not entirely inspired by the W=1
stuff that 0day turned on.
There's also been a fairly large crop of new drivers, and a few
bugfixes for existing drivers.
- Mode setting support for MT6397 and DA9211.
- New drivers for ChromeOS embedded controllers, Fairchild FAN53880,
NXP PCA9450, Qualcomm LABIBB, MP5496, and VBUS booster, and Silergy
SY8827N"
* tag 'regulator-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (67 commits)
regulator: add the sub node names for the MP5496 PMIC
regulator: cros-ec-regulator: Fix double free of desc->name.
platform/chrome: cros_ec: Fix host command for regulator control.
regulator: pca9450: Convert to use module_i2c_driver
regulator: fix memory leak on error path of regulator_register()
regulator: Replace HTTP links with HTTPS ones
regulator: convert QCOM SMD-RPM regulator document to YAML schema
regulator: gpio: Honor regulator-boot-on property
regulator: core: Add destroy_regulator()
regulator: Correct kernel-doc inconsistency
regulator: Add labibb regulator binding
regulator: qcom: Add labibb driver
regulator: Allow regulators to verify enabled during enable()
regulator: cros-ec: Constify cros_ec_regulator_voltage_ops
regulator: devres: Standardise on function documentation headers
regulator: of_regulator: Add missing colon for rdev kerneldoc argument
regulator: devres: Fix issues with kerneldoc headers
regulator: fan53880: Add support for COMPILE_TEST
regulator: fan53880: Add missing .owner field in regulator_desc
dt-bindings: regulator: add pca9450 regulator yaml
...
There are three SoC families newly dded to the 32-bit and
64-bit Arm architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012. For
now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Yy3D
-----END PGP SIGNATURE-----
Merge tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull new ARM SoC support from Arnd Bergmann:
"There are three SoC families newly dded to the 32-bit and 64-bit Arm
architecture code in the kernel this time:
- Daniel Palmer adds initial support for two chips made by MStar, a
taiwanese SoC manufacturer that became part of Mediatek in 2012.
For now, the added support is fairly minimal, with just two of its
Cortex-A7 based 32-bit camera chips getting support for a limited
set of on-chip peripherals.
- Lars Povlsen from Microchip adds support for their new Sparx5
family of ethernet switch chips using 64-bit Cortex-A53 cores.
These are descended from earlier VSC7xxx SparX and Ocelot chips
using 32-bit MIPS cores.
- Daniele Alessandrelli from Intel adds support for the new Keem Bay
SoC for computer vision, built around a Movidius VPU with Linux
running on Arm Cortex-A53 cores"
* tag 'arm-newsoc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: mstar: Correct the compatible string for pmsleep
dt-bindings: arm: mstar: remove the binding description for mstar,pmsleep
dt-bindings: mfd: syscon: add compatible string for mstar,msc313-pmsleep
ARM: mstar: Add reboot support
ARM: mstar: Add "pmsleep" node to base dtsi
ARM: mstar: Add PMU
ARM: mstar: Adjust IMI size for infinity3
ARM: mstar: Adjust IMI size for mercury5
ARM: mstar: Adjust IMI size of infinity
ARM: mstar: Add IMI SRAM region
dt-bindings: arm: mstar: Move existing MStar binding descriptions
dt-bindings: arm: mstar: Add binding details for mstar, pmsleep
ARM: mstar: Fix dts filename for 70mai midrive d08
ARM: mstar: Add dts for 70mai midrive d08
ARM: mstar: Add dts for msc313(e) based BreadBee boards
ARM: mstar: Add mercury5 series dtsis
ARM: mstar: Add infinity/infinity3 family dtsis
ARM: mstar: Add Armv7 base dtsi
ARM: mstar: Add binding details for mstar,l3bridge
ARM: mstar: Add machine for MStar/Sigmastar Armv7 SoCs
...
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
- Add support for SAMA7G5 SoC clks
- Microchip Sparx5 DPLL clk
* clk-microchip:
clk: sparx5: Add Sparx5 SoC DPLL clock driver
dt-bindings: clock: sparx5: Add bindings include file
* clk-mmp:
clk: mmp: avoid missing prototype warning
* clk-unused:
clk: drop unused function __clk_get_flags
* clk-at91:
clk: at91: sama7g5: add clock support for sama7g5
clk: at91: clk-utmi: add utmi support for sama7g5
clk: at91: clk-sam9x60-pll: re-factor to support plls with multiple outputs
clk: at91: add macro for pll ids mask
clk: at91: clk-programmable: add mux_table option
clk: at91: clk-peripheral: add support for changeable parent rate
clk: at91: clk-master: add master clock support for SAMA7G5
clk: at91: clk-generated: add mux_table option
clk: at91: clk-generated: pass the id of changeable parent at registration
clk: at91: replace conditional operator with double logical not
clk: at91: sckc: register slow_rc with accuracy option
clk: at91: sam9x60: fix main rc oscillator frequency
clk: at91: sam9x60-pll: use frac when setting frequency
clk: at91: sam9x60-pll: check fcore against ranges
clk: at91: sam9x60-pll: use logical or for range check
clk: at91: clk-sam9x60-pll: fix mul mask
clk: at91: clk-generated: check best_rate against ranges
clk: at91: clk-generated: continue if __clk_determine_rate() returns error
clk: at91: fix possible dead lock in new drivers
- Add RTC related clks on Ingenic SoCs
- Support USB PHY clks on Ingenic SoCs
* clk-fallthru:
clk: davinci: Use fallthrough pseudo-keyword
clk: imx: Use fallthrough pseudo-keyword
* clk-ingenic:
clk: X1000: Add support for calculat REFCLK of USB PHY.
clk: JZ4780: Reformat the code to align it.
clk: JZ4780: Add functions for enable and disable USB PHY.
clk: Ingenic: Add RTC related clocks for Ingenic SoCs.
dt-bindings: clock: Add tabs to align code.
dt-bindings: clock: Add RTC related clocks for Ingenic SoCs.
* clk-tegra:
clk: tegra: pll: Improve PLLM enable-state detection
* clk-sirf:
clk: clk-atlas6: fix return value check in atlas6_clk_init()
* clk-qoriq:
clk: qoriq: add LS1021A core pll mux options
- Enable CPU clks on Qualcomm IPQ6018 SoCs
- Enable CPU clks on Qualcomm MSM8996 SoCs
- GPU clk support for Qualcomm SM8150 and SM8250 SoCs
- Audio clks on Qualcomm SC7180 SoCs
- Make defines for bcm63xx-gate clks to use in DT
- Support gate clks on BCM6318 SoCs
- Add HDMI clks for BCM2711 SoCs
- Support BCM2711 SoC firmware clks
* clk-socfpga:
clk: socfpga: agilex: mpu_l2ram_clk should be mpu_ccu_clk
clk: socfpga: agilex: add nand_x_clk and nand_ecc_clk
dt-bindings: agilex: add NAND_X_CLK and NAND_ECC_CLK
* clk-doc:
clk: Clean up kernel-doc errors
clk: <linux/clk-provider.h>: drop a duplicated word
clk: add function documentation for clk_hw_round_rate()
* clk-qcom: (38 commits)
dt-bindings: clock: Fix YAML schemas for LPASS clocks on SC7180
clk: qcom: gcc-sdm660: Fix up gcc_mss_mnoc_bimc_axi_clk
clk: qcom: gcc-sdm660: Add missing modem reset
clk: qcom: lpass: Add support for LPASS clock controller for SC7180
clk: qcom: gcc: Add support for GCC LPASS clock for SC7180
dt-bindings: clock: Add YAML schemas for LPASS clocks on SC7180
clk: qcom: gdsc: Add support to enable retention of GSDCR
clk: qcom: Export gdsc_gx_do_nothing_enable() to modules
clk: qcom: Add graphics clock controller driver for SM8250
clk: qcom: Add graphics clock controller driver for SM8150
clk: qcom: add common gdsc_gx_do_nothing_enable for gpucc drivers
dt-bindings: clock: add SM8250 QCOM Graphics clock bindings
dt-bindings: clock: add SM8150 QCOM Graphics clock bindings
dt-bindings: clock: combine qcom,sdm845-gpucc and qcom,sc7180-gpucc
clk: qcom: gcc: remove unnecessary vco_table from SM8150
clk: qcom: clk-alpha-pll: use the right PCAL_DONE value for lucid pll
clk: qcom: clk-alpha-pll: same regs and ops for trion and lucid
clk: qcom: clk-alpha-pll: remove unused/incorrect PLL_CAL_VAL
clk: qcom: gcc: fix sm8150 GPU and NPU clocks
dt-bindings: clock: Fix qcom,msm8996-apcc yaml syntax
...
* clk-vc5:
clk: vc5: use a dedicated struct to describe the output drivers
dt-bindings: clk: versaclock5: convert to yaml
MAINTAINERS: take over IDT VersaClock 5 clock driver
dt-bindings: clk: versaclock5: fix 'idt' prefix typos
clk: vc5: Add memory check to prevent oops
clk: vc5: fix use of memory after it has been kfree'd
clk: vc5: Enable addition output configurations of the Versaclock
dt: Add additional option bindings for IDT VersaClock
clk: vc5: Allow Versaclock driver to support multiple instances
* clk-bcm: (44 commits)
clk: bcm2835: Do not use prediv with bcm2711's PLLs
dt-bindings: arm: bcm: Add a select to the RPI Firmware binding
clk: bcm: dvp: Add missing module informations
clk: bcm: rpi: Remove the quirks for the CPU clock
clk: bcm2835: Don't cache the PLLB rate
clk: bcm2835: Allow custom CCF flags for the PLLs
Revert "clk: bcm2835: remove pllb"
clk: bcm: rpi: Give firmware clocks a name
clk: bcm: rpi: Discover the firmware clocks
clk: bcm: rpi: Add an enum for the firmware clocks
clk: bcm: rpi: Add DT provider for the clocks
clk: bcm: rpi: Make the PLLB registration function return a clk_hw
clk: bcm: rpi: Split pllb clock hooks
clk: bcm: rpi: Rename is_prepared function
clk: bcm: rpi: Pass the clocks data to the firmware function
clk: bcm: rpi: Add clock id to data
clk: bcm: rpi: Create a data structure for the clocks
clk: bcm: rpi: Use CCF boundaries instead of rolling our own
clk: bcm: rpi: Make sure the clkdev lookup is removed
clk: bcm: rpi: Switch to clk_hw_register_clkdev
...
Multicolor is a bit too abstract. Yes, we can have
Green-Magenta-Ultraviolet LED, but so far all the LEDs we support are
RGB, and not even RGB-White or RGB-Yellow variants emerged.
Multicolor is not a good fit for RGB LED. It does not really know
about LED color. In particular, there's no way to make LED "white".
Userspace is interested in knowing "this LED can produce arbitrary
color", which not all multicolor LEDs can.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
For SC7180 this adds the necessary properties for blowing fuses in
qfprom, Coresight fixes, GPU interconnect votes and specifies max speed
for USB controller.
SM8150 and SM8250 gains Adreno SMMU, the graphics management unit and
the GPU nodes, to enable headless GPU usage.
SDM845 gains tracing support for deep idle, GPU bus bandwidth scaling
and DB845c gains the LT9611 HDMI bridge wired up.
MSM8994 gains SMD RPM and SCM support and a new dts for the Sony Xperia
Z5.
MSM8992 is refactored and modernized and gets support for SCM, SPMI,
BLSP2 UART and I2C nodes, PMU, RPM clock controller, PSCI and proper CPU
definitions. Support for the Xiaomi Libra and Microsoft Lumia 950 are
added.
-----BEGIN PGP SIGNATURE-----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=FfiE
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT additional updates for 5.9
For SC7180 this adds the necessary properties for blowing fuses in
qfprom, Coresight fixes, GPU interconnect votes and specifies max speed
for USB controller.
SM8150 and SM8250 gains Adreno SMMU, the graphics management unit and
the GPU nodes, to enable headless GPU usage.
SDM845 gains tracing support for deep idle, GPU bus bandwidth scaling
and DB845c gains the LT9611 HDMI bridge wired up.
MSM8994 gains SMD RPM and SCM support and a new dts for the Sony Xperia
Z5.
MSM8992 is refactored and modernized and gets support for SCM, SPMI,
BLSP2 UART and I2C nodes, PMU, RPM clock controller, PSCI and proper CPU
definitions. Support for the Xiaomi Libra and Microsoft Lumia 950 are
added.
* tag 'qcom-arm64-for-5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (31 commits)
arm64: dts: qcom: Add Microsoft Lumia 950 (Talkman) device tree
arm64: dts: qcom: Add Xiaomi Libra (Mi 4C) device tree
arm64: dts: qcom: msm8992: Add RPMCC node
arm64: dts: qcom: msm8992: Add PSCI support.
arm64: dts: qcom: msm8992: Add PMU node
arm64: dts: qcom: msm8992: Add BLSP2_UART2 and I2C nodes
arm64: dts: qcom: msm8992: Add SPMI PMIC arbiter device
arm64: dts: qcom: msm8992: Add a SCM node
arm64: dts: qcom: msm8992: Add a proper CPU map
arm64: dts: qcom: bullhead: Move UART pinctrl to SoC
arm64: dts: qcom: bullhead: Add qcom,msm-id
arm64: dts: qcom: msm8992: Fix SDHCI1
arm64: dts: qcom: msm8992: Modernize the DTS style
arm64: dts: qcom: Add support for Sony Xperia Z5 (SoMC Sumire-RoW)
arm64: dts: qcom: Move msm8994-smd-rpm contents to lg-bullhead.
arm64: dts: qcom: msm8994: Add support for SMD RPM
arm64: dts: qcom: msm8992: Add a label to rpm-requests
arm64: dts: qcom: msm8994: Add SCM node
arm64: dts: qcom: sdm845-db845c: Add hdmi bridge nodes
arm64: dts: qcom: add sm8250 GPU nodes
...
Link: https://lore.kernel.org/r/20200730052003.649940-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Sparx5 support 9 different clock outputs. This include file has
defines for each supported clock ordinal.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200727084211.6632-8-lars.povlsen@microchip.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add RPMH_REGULATOR_LEVEL_SVS_L0, used by sm8250.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200709135251.643-13-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The "JZ4780_CLK_LCD0PIXCLK" and the "JZ4780_CLK_LCD1PIXCLK"
in the "jz4780.h" and the new added "JZ4780_CLK_EXCLK_DIV512"
in the previous patch is too long, add tabs to other lines
to align them.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200725051136.58220-3-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add RTC related clocks bindings for the JZ4780 SoC, the X1000 SoC,
and the X1830 SoC from Ingenic.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200725051136.58220-2-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This will be required in order to support the
modem upstream.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200726111215.22361-2-konradybcio@gmail.com
Fixes: f2a76a2955 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM660")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Right now the direction of a DAI has to be specified as a literal
number in the device tree, e.g.:
dai@0 {
reg = <0>;
direction = <2>;
};
but this does not make it immediately clear that this is a
playback/RX-only DAI.
Actually, q6asm-dai.c has useful defines for this. Move them to the
dt-bindings header to allow using them in the dts(i) files.
The example above then becomes:
dai@0 {
reg = <0>;
direction = <Q6ASM_DAI_RX>;
};
which is immediately recognizable as playback/RX-only DAI.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200727082502.2341-1-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The LPASS(Low Power Audio Subsystem) clock provider have a bunch of generic
properties that are needed in a device tree. Also add clock ids for GCC
LPASS and LPASS Core clock IDs for LPASS client to request for the clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1595606878-2664-3-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Add platforms chipid nodes for am65x and j721e
- Update latest data sheet values for MMC on am65x
- Add serdes and usb3 support for j721e
- Add analog audio support for j721e
- Add SD card support for am65x
- Rename DT nodes for gic-its/smmu to their standard counterparts am65x/j721e
- HTTP links replaced with HTTPS ones
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEtQ6szHmfiBT7fujkyvq9MXlQGhEFAl8aj4cQHHQta3Jpc3Rv
QHRpLmNvbQAKCRDK+r0xeVAaEfxHD/4kE90nx+EyiSGQ5ZCNfoXs/0JB95KAGGcv
23PGvjYBfD/GFGvbL+4F7GTptqEJrkJXMcfCIR2Nv5fjhA+OjjPMzj73octytasN
iRc+ESXLgD07bLdTWEvGvMqBaslfLOajs2PSu7LOMGK6NihRiqCGR5urk6e8h0Jt
gY4gb1EFN01VIYB7n3xy7CgpHx/G6g0VJ1TjpEZVyM5G3K50/qrKzJmxX9MIiVBm
o9E85dveFe3yxvI6BepwQpfrrVg5j6xlJCHrQ0xepPiKAjCzlTaxOdTm2omGemES
h7DQ2CAD23SJ+SnF4bCltoNw/1GOfw1CoslB9X4FdvSBknp61VjrfeGp9PKZHxFI
EvEV1tmpAFAhxSlY4zcyhmpMcBiKzGojGExK0COt5hHm7ssbTIaDKNTTJByzI1cJ
FkHr609ktYmSyfg9JVejiCPa9D/8etYqkgy/9edM4iYLss4TkPGHHD+C0iqMQaCA
mcOsquOaTnbiATQuqAaoLzZbUKSO4R57DgXAO7+XzOgaQutBRJ5VMgREM8apNYUa
baE779XQfCMiOpgEpEpwQMVVgt6S/PUXis6yZy2BpP3npbKVKI53f0wpZc0FvM8e
9J5cpWBLX1qK0lO8KinGRfW09+EcSlbWe2Byh1EKfqogRsfJlsPYyAuEg3BwDr1o
XMQS/p1aPQ==
=0bPs
-----END PGP SIGNATURE-----
Merge tag 'ti-k3-dt-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into arm/dt
Texas Instruments K3 SoC DT updates for v5.9
- Add platforms chipid nodes for am65x and j721e
- Update latest data sheet values for MMC on am65x
- Add serdes and usb3 support for j721e
- Add analog audio support for j721e
- Add SD card support for am65x
- Rename DT nodes for gic-its/smmu to their standard counterparts am65x/j721e
- HTTP links replaced with HTTPS ones
* tag 'ti-k3-dt-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: k3-j721e-proc-board: Add wait time for sampling Type-C DIR line
arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0
arm64: dts: ti: k3-j721e-main.dtsi: Add USB to SERDES MUX
arm64: dts: ti: k3-j721e-main: Add system controller node and SERDES lane mux
arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller
arm64: dts: ti: k3-am65/j721e-main: rename gic-its node to msi-controller
arm64: dts: ti: k3-j721e-main: rename smmu node to iommu
arm64: dts: ti: k3-*: Replace HTTP links with HTTPS ones
arm64: dts: ti: k3-am654-base-board: Add support for SD card
arm64: dts: ti: k3-am65-main: Add support for sdhci1
arm64: dts: ti: j721e-common-proc-board: Analog audio support
arm64: dts: ti: k3-j721e-common-proc-board: Remove duplicated main_i2c1_exp4_pins_default
arm64: dts: ti: k3-am654-main: Update otap-del-sel values
arm64: dts: ti: k3-j721e-mcu-wakeup: add k3 platforms chipid module node
arm64: dts: ti: k3-am65-wakeup: add k3 platforms chipid module node
Link: https://lore.kernel.org/r/3b3b9214-769d-ba1b-db5e-44414a8c5756@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add device tree bindings for graphics clock controller for
Qualcomm Technology Inc's SM8250 SoCs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-9-jonathan@marek.ca
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add device tree bindings for graphics clock controller for
Qualcomm Technology Inc's SM8150 SoCs.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-8-jonathan@marek.ca
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8ZqeUACgkQqDIjiipP
6E9tawf/UGUhEfB+VmH9w60NJlM0fC5a/TjVOb4yMjTZjjdyd4zMBHemF+dqMNnw
wTr+S8U9QfvP4BDgg1hWV+vhAwxz2xkhR0cGtOQjck5322vZglGSmAVqTCAlQMoZ
LNm98XeUYYVNMB+/+BHkf8F/nHV9vRo8sJg7UnvX/6RCykXFYXVP+P8LfkAU1MPt
8vaRPCcyGnYXrgjDYY5M5qYudLNpFPrzr1yJDWdwWUliwH3T1X1FNogTdUo955qk
wM+Hb4yPRuRufM+yATPsRedQypZFpoWFObuEMD2FaIw/LZVxV7D1tmw5KhL2V1tZ
XSzNiJDEgri/4LaVzXKP7sVlQlZfDQ==
=DXTp
-----END PGP SIGNATURE-----
Merge tag 'timers-v5.9' of https://git.linaro.org/people/daniel.lezcano/linux into timers/core
Pull clock event/surce driver changes from Daniel Lezcano:
- Add sama5d2 support and rework the 32kHz clock handling (Alexandre Belloni)
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
- Add support for i.MX TPM driver with ARM64 (Anson Huang)
- Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
- Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
- Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
- Add support for the Ingenic X1000 OST (Zhou Yanjie)
Add the OST bindings for the X1000 SoC from Ingenic.
Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200722171804.97559-2-zhouyanjie@wanyeetech.com
This tag moves the reset-simple header out of drivers/reset for use by
drivers outside of drivers/reset, adds a .reset() callback to
reset-simple, converts i.MX reset bindings to json-schema, fixes a
compile warning in the reset-intel-gw driver, and replaces some HTTP
links with HTTPS ones in comments.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCXxWSARcccC56YWJlbEBw
ZW5ndXRyb25peC5kZQAKCRDVhaclGDdiwAP6AP4ld+W8CqwjEw+tkTVoCcGpE3v4
rmeEao1MtXtttiG9bAEAl2y794/zu0cXI0UEYqbhuqDYG/z8uXoBRvTGEP7UqQc=
=tScp
-----END PGP SIGNATURE-----
Merge tag 'reset-for-v5.9' of git://git.pengutronix.de/pza/linux into arm/drivers
Reset controller updates for v5.9
This tag moves the reset-simple header out of drivers/reset for use by
drivers outside of drivers/reset, adds a .reset() callback to
reset-simple, converts i.MX reset bindings to json-schema, fixes a
compile warning in the reset-intel-gw driver, and replaces some HTTP
links with HTTPS ones in comments.
* tag 'reset-for-v5.9' of git://git.pengutronix.de/pza/linux:
reset: Replace HTTP links with HTTPS ones
reset: intel: fix a compile warning about REG_OFFSET redefined
dt-bindings: reset: Convert i.MX7 reset to json-schema
dt-bindings: reset: Convert i.MX reset to json-schema
reset: simple: Add reset callback
reset: Move reset-simple header out of drivers/reset
Link: https://lore.kernel.org/r/b718f052e38abbaac599d80645376b75e54aa5bd.camel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Sparx5 support 9 different clock outputs. This include file has
defines for each supported clock ordinal.
Link: https://lore.kernel.org/r/20200615133242.24911-8-lars.povlsen@microchip.com
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New board support: Protonic PRTI6Q/WD2/VT7/RVT and MYiR MYS-6ULX SBC.
- Update IIM, OCOTP and SD/MMC device node name to match .yaml bindings.
- Make tempmon node as child of anatop node according to hardware
architecture.
- The vf610-zii device update: configure fiber port to 1000BaseX, add
switch watchdog, MDIO speed and preamble.
- A series from Fabio Estevam to update imx6qdl-sabresd and
imx6q-tbs2910 for using MDIO node and reset-assert-us.
- Align L2 cache-controller device node name with .yaml schema.
- Enable SATA support for imx6qp-sabreauto and imx6qp-sabresd board.
- A series of patches from Shengjiu Wang to enable various audio
support on i.MX6 devices.
- Add Gateworks System Controller support for imx6qdl-gw devices.
- Change default #pwm-cells setting to <3> in the SoC dtsi files.
- Other small random changes.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl8VVgcUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM7azwf+KzAukegArKtAmsbAnYNKYztXXifW
6Hc3+hv2mfUtsGfHPSUJJ5MhEW52xAbcXnYETUkmoWe1W1zIxrNNWvBUm4nPF5os
0cO8tjk4cE4CYDnsl8sBSqT55sd3ke61I+j9q0NAQNyX9OlmZ3kfm8yw0yIsxTKp
/FzoLmOeRzhVKHdZczuJ9Ts4kFyf3XtQrrN1UTbu715KdIbbsrJtXQ74ADBCnjfX
8RUm3Y5XIaPcF4z2U8reMsbHCF120ENIfGwFRNo/Odx+1OVo1IrDB1+f/SP9ZP0T
6+iKvfSS4RavzB1tvLdJ2/911t7qtqsneU33kwQKL0wrFZsT4ih42uBfpw==
=1hHY
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree update for 5.9:
- New board support: Protonic PRTI6Q/WD2/VT7/RVT and MYiR MYS-6ULX SBC.
- Update IIM, OCOTP and SD/MMC device node name to match .yaml bindings.
- Make tempmon node as child of anatop node according to hardware
architecture.
- The vf610-zii device update: configure fiber port to 1000BaseX, add
switch watchdog, MDIO speed and preamble.
- A series from Fabio Estevam to update imx6qdl-sabresd and
imx6q-tbs2910 for using MDIO node and reset-assert-us.
- Align L2 cache-controller device node name with .yaml schema.
- Enable SATA support for imx6qp-sabreauto and imx6qp-sabresd board.
- A series of patches from Shengjiu Wang to enable various audio
support on i.MX6 devices.
- Add Gateworks System Controller support for imx6qdl-gw devices.
- Change default #pwm-cells setting to <3> in the SoC dtsi files.
- Other small random changes.
* tag 'imx-dt-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (43 commits)
ARM: dts: vf610-zii-ssmb-spu3: Add node for switch watchdog
ARM: dts: vf610-zii-ssmb-dtu: Add no-sdio/no-sd properties
ARM: dts: imx6q-tbs2910: Pass reset-assert-us
ARM: dts: imx6q-tbs2910: Add an mdio node
ARM: dts: imx6qdl-sabresd: Pass reset-assert-us
ARM: dts: imx6qdl-sabresd: Add an mdio node
ARM: dts: imx6qdl-gw: add Gateworks System Controller support
ARM: dts: imx6ull: add MYiR MYS-6ULX SBC
ARM: dts: vf610-zii-spb4: Add node for switch watchdog
ARM: dts: colibri-imx6: remove pinctrl-names orphan
ARM: dts: imx: default to #pwm-cells = <3> in the SoC dtsi files
ARM: dts: vf610-zii-scu4-aib: Configure fibre ports to 1000BaseX
ARM: dts: vf610-zii-dev-rev-c: Configure fiber port to 1000BaseX
ARM: dts: ZII: update MDIO speed and preamble
ARM: dts: vfxxx: Add node for CAAM
ARM: dts: imx6qp-sabresd: enable sata
ARM: dts: imx6qp-sabreauto: enable sata
ARM: dts: add Protonic RVT board
ARM: dts: add Protonic VT7 board
ARM: dts: add Protonic WD2 board
...
Link: https://lore.kernel.org/r/20200720085536.24138-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* clk-qcom:
clk: qcom: gcc: Make disp gpll0 branch aon for sc7180/sdm845
ipq806x: gcc: add support for child probe
clk: qcom: msm8996: Make symbol 'cpu_msm8996_clks' static
clk: qcom: ipq8074: Add correct index for PCIe clocks
The PCIe clocks GCC_PCIE0_AXI_S_BRIDGE_CLK, GCC_PCIE0_RCHNG_CLK_SRC,
GCC_PCIE0_RCHNG_CLK are wrongly added to the gcc reset group.
Move them to the gcc clock group.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1594877570-9280-1-git-send-email-sivaprak@codeaurora.org
Fixes: e7fb524cfc ("dt-bindings: clock: qcom: ipq8074: Add missing bindings for PCIe")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Introduce support for touchscreen channels found in JZ47xx SoCs.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The system controller node manages the CTRL_MMR0 region.
Add serdes_ln_ctrl node which is used for controlling the SERDES lane mux.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The ZynqMP includes the DisplayPort subsystem with its own DMA engine
called DPDMA. The DPDMA IP comes with 6 individual channels
(4 for display, 2 for audio). This documentation describes DT bindings
of DPDMA.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200717013337.24122-2-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add DT bindings for the LEDs multicolor class framework.
Add multicolor ID to the color ID list for device tree bindings.
CC: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Add rpm smd clocks, PMIC and bus clocks which are required on MSM8992,
MSM8994 (and APQ variants) for clients to vote on.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623230018.303776-1-konradybcio@gmail.com
[sboyd@kernel.org: Fixed up binding numbers]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds description for MT6779 IOMMU.
MT6779 has two iommus, they are mm_iommu and apu_iommu which
both use ARM Short-Descriptor translation format.
In addition, mm_iommu and apu_iommu are two independent HW instance
, we need to set them separately.
The MT6779 IOMMU hardware diagram is as below, it is only a brief
diagram about iommu, it don't focus on the part of smi_larb, so
I don't describe the smi_larb detailedly.
EMI
|
--------------------------------------
| |
MM_IOMMU APU_IOMMU
| |
SMI_COMMOM----------- APU_BUS
| | |
SMI_LARB(0~11) | |
| | |
| | --------------
| | | | |
Multimedia engine CCU VPU MDLA EMDA
All the connections are hardware fixed, software can not adjust it.
Signed-off-by: Chao Hao <chao.hao@mediatek.com>
Reviewed-by: Rob Herring <robh+dt@kernel.org>
Link: https://lore.kernel.org/r/20200703044127.27438-2-chao.hao@mediatek.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Increase #pinctrl-cells to 2 so that mux and conf be kept separate. This
requires the AM33XX_PADCONF macro in omap.h to also be modified to keep pin
conf and pin mux values separate.
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Link: https://lore.kernel.org/r/20200701013320.130441-3-drew@beagleboard.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patchset adds support for being able to change regulator modes for
the mt6397 regulator. This is needed to allow the voltage scaling
support in the MT8173 SoC to be used on the elm (Acer Chromebook R13)
and hana (several Lenovo Chromebooks) devices.
Without a of_map_mode implementation, the regulator-allowed-modes
devicetree field is skipped, and attempting to change the regulator mode
results in an error:
[ 1.439165] vpca15: mode operation not allowed
Changes in v2:
- Introduce constants in dt-bindings
- Improve conditional readability
Anand K Mistry (4):
regulator: mt6397: Move buck modes into header file
dt-bindings: regulator: mt6397: Document valid modes
regulator: mt6397: Implement of_map_mode
arm64: dts: mediatek: Update allowed mt6397 regulator modes for elm
boards
.../bindings/regulator/mt6397-regulator.txt | 3 +++
arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi | 4 +++-
drivers/regulator/mt6397-regulator.c | 17 ++++++++++++++---
.../regulator/mediatek,mt6397-regulator.h | 15 +++++++++++++++
4 files changed, 35 insertions(+), 4 deletions(-)
create mode 100644 include/dt-bindings/regulator/mediatek,mt6397-regulator.h
--
2.27.0.212.ge8ba1cc988-goog
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Add DT bindings for the Xilinx ZynqMP PHY. ZynqMP SoCs have a High Speed
Processing System Gigabit Transceiver which provides PHY capabilities to
USB, SATA, PCIE, Display Port and Ehernet SGMII controllers.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200629120054.29338-2-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Make defines for bcm63xx-gate clks to use in DT
- Support gate clks on BCM6318 SoCs
- Add HDMI clks for BCM2711 SoCs
- Support BCM2711 SoC firmware clks
* clk-bcm: (42 commits)
clk: bcm: dvp: Add missing module informations
clk: bcm: rpi: Remove the quirks for the CPU clock
clk: bcm2835: Don't cache the PLLB rate
clk: bcm2835: Allow custom CCF flags for the PLLs
Revert "clk: bcm2835: remove pllb"
clk: bcm: rpi: Give firmware clocks a name
clk: bcm: rpi: Discover the firmware clocks
clk: bcm: rpi: Add an enum for the firmware clocks
clk: bcm: rpi: Add DT provider for the clocks
clk: bcm: rpi: Make the PLLB registration function return a clk_hw
clk: bcm: rpi: Split pllb clock hooks
clk: bcm: rpi: Rename is_prepared function
clk: bcm: rpi: Pass the clocks data to the firmware function
clk: bcm: rpi: Add clock id to data
clk: bcm: rpi: Create a data structure for the clocks
clk: bcm: rpi: Use CCF boundaries instead of rolling our own
clk: bcm: rpi: Make sure the clkdev lookup is removed
clk: bcm: rpi: Switch to clk_hw_register_clkdev
clk: bcm: rpi: Remove pllb_arm_lookup global pointer
clk: bcm: rpi: Make sure pllb_arm is removed
...
The VersaClock driver now supports some additional bindings to support
child nodes which can configure optional settings like mode, voltage
and slew.
This patch updates the binding document to describe what is available
in the driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200603154329.31579-2-aford173@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add rpm smd clocks, PMIC and bus clocks which are required on
SDM630/660 (and APQ variants) for clients to vote on.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200622090252.36568-1-konradybcio@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add header with BCM63268 definitions in order to be able to include it from
device tree files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20200615090231.2932696-8-noltari@gmail.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add header with BCM6368 definitions in order to be able to include it from
device tree files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20200615090231.2932696-7-noltari@gmail.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add header with BCM6362 definitions in order to be able to include it from
device tree files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20200615090231.2932696-6-noltari@gmail.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add header with BCM6358 definitions in order to be able to include it from
device tree files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20200615090231.2932696-5-noltari@gmail.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add header with BCM6328 definitions in order to be able to include it from
device tree files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20200615090231.2932696-4-noltari@gmail.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add header with BCM6318 definitions in order to be able to include it from
device tree files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20200615090231.2932696-3-noltari@gmail.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add header with BCM3368 definitions in order to be able to include it from
device tree files.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://lore.kernel.org/r/20200615090231.2932696-2-noltari@gmail.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add documentation for PMIC7 ADC peripheral.
For the PMIC7-type PMICs, ADC peripheral is present in HW for the
following PMICs: PMK8350, PM8350, PM8350b, PMR735a and PMR735b.
Of these, only the ADC peripheral on PMK8350 is exposed directly to SW.
If SW needs to communicate with ADCs on other PMICs, it specifies the
PMIC to PMK8350 through the newly added SID register and communication
between PMK8350 ADC and other PMIC ADCs is carried out through
PBS(Programmable Boot Sequence) at the firmware level.
In addition, add definitions for ADC channels and virtual channel
definitions (combination of ADC channel number and PMIC SID number)
per PMIC, to be used by ADC clients for PMIC7.
Signed-off-by: Jishnu Prakash <jprakash@codeaurora.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
new controller driver for IPCC
reorg the of_device data
add support for ipq6018 platform
- spreadtrum:
new sprd controller driver
- imx:
implement suspend/resume PM support
- Misc :
make pcc driver struct as static
fix return value in imx_mu_scu
disable clock before bailout in imx probe
remove duplicate error mssg in zynqmp probe
fix header size in imx.scu
check for null instead of is-err in zynqmp
-----BEGIN PGP SIGNATURE-----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=FpYp
-----END PGP SIGNATURE-----
Merge tag 'mailbox-v5.8' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
"qcom:
- new controller driver for IPCC
- reorg the of_device data
- add support for ipq6018 platform
spreadtrum:
- new sprd controller driver
imx:
- implement suspend/resume PM support
misc:
- make pcc driver struct static
- fix return value in imx_mu_scu
- disable clock before bailout in imx probe
- remove duplicate error mssg in zynqmp probe
- fix header size in imx.scu
- check for null instead of is-err in zynqmp"
* tag 'mailbox-v5.8' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: qcom: Add ipq6018 apcs compatible
mailbox: qcom: Add clock driver name in apcs mailbox driver data
dt-bindings: mailbox: Add YAML schemas for QCOM APCS global block
mailbox: imx: ONLY IPC MU needs IRQF_NO_SUSPEND flag
mailbox: imx: Add runtime PM callback to handle MU clocks
mailbox: imx: Add context save/restore for suspend/resume
MAINTAINERS: Add entry for Qualcomm IPCC driver
mailbox: Add support for Qualcomm IPCC
dt-bindings: mailbox: Add devicetree binding for Qcom IPCC
mailbox: zynqmp-ipi: Fix NULL vs IS_ERR() check in zynqmp_ipi_mbox_probe()
mailbox: imx-mailbox: fix scu msg header size check
mailbox: sprd: Add Spreadtrum mailbox driver
dt-bindings: mailbox: Add the Spreadtrum mailbox documentation
mailbox: ZynqMP IPI: Delete an error message in zynqmp_ipi_probe()
mailbox: imx: Disable the clock on devm_mbox_controller_register() failure
mailbox: imx: Fix return in imx_mu_scu_xlate()
mailbox: imx: Support runtime PM
mailbox: pcc: make pcc_mbox_driver static
function that isn't used anymore. Otherwise the main new thing for the common
clk framework is that it is selectable in the Kconfig language now. Hopefully
this will let clk drivers and clk consumers be testable on more than the
architectures that support the clk framework. The goal is to introduce some
Kunit tests for the framework.
Outside of the core framework we have the usual set of various driver updates
and non-critical fixes. The dirstat shows that the new Baikal-T1 driver is the
largest addition this time around in terms of lines of code. After that the x86
(Intel), Qualcomm, and Mediatek drivers introduce many lines to support new or
upcoming SoCs. After that the dirstat shows the usual suspects working on their
SoC support by fixing minor bugs, correcting data and converting some of their
DT bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix clock support
on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and clk-pllv3
drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support aarch32 mode on
aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using composite
clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102 defined
bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+
-----BEGIN PGP SIGNATURE-----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=nuG5
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
kernel cycle.
New drivers:
- Intel Jasper Lake support.
- NXP Freescale i.MX8DXL support.
- Qualcomm SM8250 support.
- Renesas R8A7742 SH-PFC support.
Driver improvements:
- Severe cleanup and modernization of the MCP23s08 driver.
- Mediatek driver modularized.
- Setting config supported in the Meson driver.
- Wakeup support for the Broadcom BCM7211.
-----BEGIN PGP SIGNATURE-----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=3UGk
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.8 kernel cycle.
It's just really boring this time. Zero core changes. Just linear
development, cleanups and misc noncritical fixes. Some new drivers for
very new Qualcomm and Intel chips.
New drivers:
- Intel Jasper Lake support.
- NXP Freescale i.MX8DXL support.
- Qualcomm SM8250 support.
- Renesas R8A7742 SH-PFC support.
Driver improvements:
- Severe cleanup and modernization of the MCP23s08 driver.
- Mediatek driver modularized.
- Setting config supported in the Meson driver.
- Wakeup support for the Broadcom BCM7211"
* tag 'pinctrl-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sprd: Fix the incorrect pull-up definition
pinctrl: pxa: pxa2xx: Remove 'pxa2xx_pinctrl_exit()' which is unused and broken
pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'
pinctrl: freescale: imx: Fix an error handling path in 'imx_pinctrl_probe()'
pinctrl: sirf: add missing put_device() call in sirfsoc_gpio_probe()
pinctrl: imxl: Fix an error handling path in 'imx1_pinctrl_core_probe()'
pinctrl: bcm2835: Add support for wake-up interrupts
pinctrl: bcm2835: Match BCM7211 compatible string
dt-bindings: pinctrl: Document optional BCM7211 wake-up interrupts
dt-bindings: pinctrl: Document 7211 compatible for brcm, bcm2835-gpio.txt
dt-bindings: pinctrl: stm32: Add missing interrupts property
pinctrl: at91-pio4: Add COMPILE_TEST support
pinctrl: Fix return value about devm_platform_ioremap_resource()
MAINTAINERS: Renesas Pin Controllers are supported
dt-bindings: pinctrl: ocelot: Add Sparx5 SoC support
pinctrl: ocelot: Fix GPIO interrupt decoding on Jaguar2
pinctrl: ocelot: Remove instance number from pin functions
pinctrl: ocelot: Always register GPIO driver
dt-bindings: pinctrl: rockchip: update example
pinctrl: amd: Add ACPI dependency
...
Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzkHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yldOwCgus/DgpnI1UL4z+NdBxJrAXtkPmgAn2sgTUea
i5RblCmcVMqvHaGtYkY+
=tScN
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc driver patches for 5.8-rc1
Included in here are:
- habanalabs driver updates, loads
- mhi bus driver updates
- extcon driver updates
- clk driver updates (approved by the clock maintainer)
- firmware driver updates
- fpga driver updates
- gnss driver updates
- coresight driver updates
- interconnect driver updates
- parport driver updates (it's still alive!)
- nvmem driver updates
- soundwire driver updates
- visorbus driver updates
- w1 driver updates
- various misc driver updates
In short, loads of different driver subsystem updates along with the
drivers as well.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (233 commits)
habanalabs: correctly cast u64 to void*
habanalabs: initialize variable to default value
extcon: arizona: Fix runtime PM imbalance on error
extcon: max14577: Add proper dt-compatible strings
extcon: adc-jack: Fix an error handling path in 'adc_jack_probe()'
extcon: remove redundant assignment to variable idx
w1: omap-hdq: print dev_err if irq flags are not cleared
w1: omap-hdq: fix interrupt handling which did show spurious timeouts
w1: omap-hdq: fix return value to be -1 if there is a timeout
w1: omap-hdq: cleanup to add missing newline for some dev_dbg
/dev/mem: Revoke mappings when a driver claims the region
misc: xilinx-sdfec: convert get_user_pages() --> pin_user_pages()
misc: xilinx-sdfec: cleanup return value in xsdfec_table_write()
misc: xilinx-sdfec: improve get_user_pages_fast() error handling
nvmem: qfprom: remove incorrect write support
habanalabs: handle MMU cache invalidation timeout
habanalabs: don't allow hard reset with open processes
habanalabs: GAUDI does not support soft-reset
habanalabs: add print for soft reset due to event
habanalabs: improve MMU cache invalidation code
...
Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzqVA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynftwCfeanyI6TR5AdfJVZN50B6/ySvVwcAn07i9VRX
tnt2kz0UqReYpLt0wyJ7
=YP7o
-----END PGP SIGNATURE-----
Merge tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY driver updates from Greg KH:
"Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (245 commits)
usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs
usb: dwc3: meson-g12a: fix error path when fetching the reset line fails
Revert "dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings"
Revert "dt-bindings: usb: qcom,dwc3: Add compatible for SC7180"
Revert "dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver"
USB: serial: ch341: fix lockup of devices with limited prescaler
USB: serial: ch341: add basis for quirk detection
CDC-ACM: heed quirk also in error handling
USB: serial: option: add Telit LE910C1-EUX compositions
usb: musb: Fix runtime PM imbalance on error
usb: musb: jz4740: Prevent lockup when CONFIG_SMP is set
usb: musb: mediatek: add reset FADDR to zero in reset interrupt handle
usb: musb: use true for 'use_dma'
usb: musb: start session in resume for host port
usb: musb: return -ESHUTDOWN in urb when three-strikes error happened
USB: serial: qcserial: add DW5816e QDL support
thunderbolt: Add trivial .shutdown
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
...
This is the set of device tree changes, mostly covering new
hardware support, with 577 patches touching a little over 500
files.
There are five new Arm SoCs supported in this release, all of
them for existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in
both NAS devices and Android Set-top-box designs, along
with the "Horseradish", "Lion Skin" and "Mjolnir" reference
platforms; the Mele X1000 and Xnano X5 set-top-boxes and
the Banana Pi BPi-M4 single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC
and the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the
Odroid-GO Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2"
and YADRO OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform"
reference board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board
computer and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in existing
SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=17kt
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"This is the set of device tree changes, mostly covering new hardware
support, with 577 patches touching a little over 500 files.
There are five new Arm SoCs supported in this release, all of them for
existing SoC families:
- Realtek RTD1195, RTD1395 and RTD1619 -- three SoCs used in both NAS
devices and Android Set-top-box designs, along with the
"Horseradish", "Lion Skin" and "Mjolnir" reference platforms; the
Mele X1000 and Xnano X5 set-top-boxes and the Banana Pi BPi-M4
single-board computer.
- Renesas RZ/G1H (r8a7742) -- a high-end 32-bit industrial SoC and
the iW-RainboW-G21D-Qseven-RZG1H board/SoM
- Rockchips RK3326 -- low-end 64-bit SoC along with the Odroid-GO
Advance game console
Newly added machines on already supported SoCs are:
- AMLogic S905D based Smartlabs SML-5442TW TV box
- AMLogic S905X3 based ODROID-C4 SBC
- AMLogic S922XH based Beelink GT-King Pro TV box
- Allwinner A20 based Olimex A20-OLinuXino-LIME-eMMC SBC
- Aspeed ast2500 based BMCs in Facebook x86 "Yosemite V2" and YADRO
OpenPower P9 "Nicole"
- Marvell Kirkwood based Check Point L-50 router
- Mediatek MT8173 based Elm/Hana Chromebook laptops
- Microchip SAMA5D2 "Industrial Connectivity Platform" reference
board
- NXP i.MX8m based Beacon i.MX8m-Mini SoM development kit
- Octavo OSDMP15x based Linux Automation MC-1 development board
- Qualcomm SDM630 based Xiaomi Redmi Note 7 phone
- Realtek RTD1295 based Xnano X5 TV Box
- STMicroelectronics STM32MP1 based Stinger96 single-board computer
and IoT Box
- Samsung Exynos4210 based based Samsung Galaxy S2 phone
- Socionext Uniphier based Akebi96 SBC
- TI Keystone based K2G Evaluation board
- TI am5729 based Beaglebone-AI development board
Include device descriptions for additional hardware support in
existing SoCs and machines based on all major SoC platforms:
- AMlogic Meson
- Allwinner sunxi
- Arm Juno/VFP/Vexpress/Integrator
- Broadcom bcm283x/bcm2711
- Hisilicon hi6220
- Marvell EBU
- Mediatek MT27xx, MT76xx, MT81xx and MT67xx
- Microchip SAMA5D2
- NXP i.MX6/i.MX7/i.MX8 and Layerscape
- Nvidia Tegra
- Qualcomm Snapdragon
- Renesas r8a77961, r8a7791
- Rockchips RK32xx/RK33xx
- ST-Ericsson ux500
- STMicroelectronics SMT32
- Samsung Exynos and S5PV210
- Socionext Uniphier
- TI OMAP5/DRA7 and Keystone"
* tag 'arm-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (564 commits)
ARM: dts: keystone: Rename "msmram" node to "sram"
arm: dts: mt2712: add uart APDMA to device tree
arm64: dts: mt8183: add mmc node
arm64: dts: mt2712: add ethernet device node
arm64: tegra: Make the RTC a wakeup source on Jetson Nano and TX1
ARM: dts: mmp3: Add the fifth SD HCI
ARM: dts: berlin*: Fix up the SDHCI node names
ARM: dts: mmp3: Fix USB & USB PHY node names
ARM: dts: mmp3: Fix L2 cache controller node name
ARM: dts: mmp*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa*: Fix up encoding of the /rtc interrupts property
ARM: dts: pxa910: Fix the gpio interrupt cell number
ARM: dts: pxa3xx: Fix up encoding of the /gpio interrupts property
ARM: dts: pxa168: Fix the gpio interrupt cell number
ARM: dts: pxa168: Add missing address/size cells to i2c nodes
ARM: dts: dove: Fix interrupt controller node name
ARM: dts: kirkwood: Fix interrupt controller node name
arm64: dts: Add SC9863A emmc and sd card nodes
arm64: dts: Add SC9863A clock nodes
arm64: dts: mt6358: add PMIC MT6358 related nodes
...
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for Qualcomm's MSM8939 Generic Clock Controller
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
* clk-mmp:
clk: mmp2: Add audio clock controller driver
dt-bindings: clock: Add Marvell MMP Audio Clock Controller binding
clk: mmp2: Add support for power islands
dt-bindings: marvell,mmp2: Add ids for the power domains
dt-bindings: clock: Make marvell,mmp2-clock a power controller
clk: mmp2: Add the audio clock
clk: mmp2: Add the I2S clocks
clk: mmp2: Rename mmp2_pll_init() to mmp2_main_clk_init()
clk: mmp2: Move thermal register defines up a bit
dt-bindings: marvell,mmp2: Add clock id for the Audio clock
dt-bindings: marvell,mmp2: Add clock id for the I2S clocks
clk: mmp: frac: Allow setting bits other than the numerator/denominator
clk: mmp: frac: Do not lose last 4 digits of precision
* clk-intel:
clk: intel: remove redundant initialization of variable rate64
clk: intel: Add CGU clock driver for a new SoC
dt-bindings: clk: intel: Add bindings document & header file for CGU
* clk-ingenic:
clk: ingenic: Mark ingenic_tcu_of_match as __maybe_unused
clk: X1000: Add FIXDIV for SSI clock of X1000.
dt-bindings: clock: Add and reorder ABI for X1000.
clk: Ingenic: Add CGU driver for X1830.
dt-bindings: clock: Add X1830 clock bindings.
clk: Ingenic: Adjust cgu code to make it compatible with X1830.
clk: Ingenic: Remove unnecessary spinlock when reading registers.
* clk-qcom:
clk: qcom: Add missing msm8998 ufs_unipro_core_clk_src
dt-bindings: clock: Add YAML schemas for QCOM A53 PLL
clk: qcom: gcc-msm8939: Add MSM8939 Generic Clock Controller
clk: qcom: gcc: Add support for Secure control source clock
dt-bindings: clock: Add gcc_sec_ctrl_clk_src clock ID
clk: qcom: gcc: Add support for a new frequency for SC7180
clk: qcom: Add DT bindings for MSM8939 GCC
clk: qcom: gcc: Add missing UFS clocks for SM8150
clk: qcom: gcc: Add GPU and NPU clocks for SM8150
clk: qcom: mmcc-msm8996: Properly describe GPU_GX gdsc
clk: qcom: gdsc: Handle GDSC regulator supplies
clk: qcom: msm8916: Fix the address location of pll->config_reg
* clk-silabs:
clk: clk-si5341: Add support for the Si5345 series
- Allow the COMMON_CLK config to be selectable
* clk-selectable:
clk: Move HAVE_CLK config out of architecture layer
MIPS: Loongson64: Drop asm/clock.h include
ARM: mmp: Remove legacy clk code
clk: Allow the common clk framework to be selectable
mmc: meson-mx-sdio: Depend on OF_ADDRESS and not just OF
MIPS: Remove redundant CLKDEV_LOOKUP selects
h8300: Remove redundant CLKDEV_LOOKUP selects
arm64: tegra: Remove redundant CLKDEV_LOOKUP selects
ARM: Remove redundant CLKDEV_LOOKUP selects
ARM: Remove redundant COMMON_CLK selects
* clk-amlogic:
clk: meson: meson8b: Don't rely on u-boot to init all GP_PLL registers
clk: meson: meson8b: Make the CCF use the glitch-free VPU mux
clk: meson: meson8b: Fix the vclk_div{1, 2, 4, 6, 12}_en gate bits
clk: meson: meson8b: Fix the polarity of the RESET_N lines
clk: meson: meson8b: Fix the first parent of vid_pll_in_sel
clk: meson: g12a: Prepare the GPU clock tree to change at runtime
clk: meson: gxbb: Prepare the GPU clock tree to change at runtime
clk: meson: meson8b: make the hdmi_sys clock tree mutable
clk: meson8b: export the HDMI system clock
* clk-renesas:
dt-bindings: clock: renesas: mstp: Convert to json-schema
dt-bindings: clock: renesas: div6: Convert to json-schema
clk: renesas: cpg-mssr: Fix STBCR suspend/resume handling
clk: renesas: rcar-gen2: Remove superfluous CLK_RENESAS_DIV6 selects
clk: renesas: cpg-mssr: Add R8A7742 support
dt-bindings: clock: renesas: cpg-mssr: Document r8a7742 binding
clk: renesas: Add r8a7742 CPG Core Clock Definitions
dt-bindings: power: rcar-sysc: Add r8a7742 power domain index macros
MAINTAINERS: Add DT Bindings for Renesas Clock Generators
clk: renesas: r9a06g032: Fix some typo in comments
dt-bindings: clock: renesas: rcar-usb2-clock-sel: Add r8a77961 support
* clk-samsung:
clk: samsung: exynos5433: Add IGNORE_UNUSED flag to sclk_i2s1
ARM/SAMSUNG EXYNOS ARM ARCHITECTURES: Use fallthrough;
clk: samsung: Fix CLK_SMMU_FIMCL3 clock name on Exynos542x
clk: samsung: Mark top ISP and CAM clocks on Exynos542x as critical
* clk-allwinner:
clk: sunxi: Fix incorrect usage of round_down()
After being gained by the CCU PLLs the signals must be transformed to
be suitable for the clock-consumers. This is done by a set of dividers
embedded into the CCU. A first block of dividers is used to create
reference clocks for AXI-bus of high-speed peripheral IP-cores of the
chip. The second block dividers alter the PLLs output signals to be then
consumed by SoC peripheral devices. Both block DT nodes are ordinary
clock-providers with standard set of properties supported. But in addition
to that each clock provider can be used to reset the corresponding clock
domain. This makes the AXI-bus and System Devices CCU DT nodes to be also
reset-providers.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@vger.kernel.org
Link: https://lore.kernel.org/r/20200526222056.18072-3-Sergey.Semin@baikalelectronics.ru
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Baikal-T1 Clocks Control Unit is responsible for transformation of a
signal coming from an external oscillator into clocks of various
frequencies to propagate them then to the corresponding clocks
consumers (either individual IP-blocks or clock domains). In order
to create a set of high-frequency clocks the external signal is
firstly handled by the embedded into CCU PLLs. So the corresponding
dts-node is just a normal clock-provider node with standard set of
properties. Note as being part of the Baikal-T1 System Controller its
DT node is supposed to be a child the system controller node.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@vger.kernel.org
Link: https://lore.kernel.org/r/20200526222056.18072-2-Sergey.Semin@baikalelectronics.ru
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
ufs_unipro_core_clk_src is required to allow UFS to clock scale for power
savings.
Fixes: b5f5f525c5 ("clk: qcom: Add MSM8998 Global Clock Control (GCC) driver")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20200528142205.44003-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
1.The SSI clock of X1000 not like JZ4770 and JZ4780, they are not
directly derived from the output of SSIPLL, but from the clock
obtained by dividing the frequency by 2. "X1000_CLK_SSIPLL_DIV2"
is added for this purpose, it must between "X1000_CLK_SSIPLL"
and "X1000_CLK_SSIMUX", otherwise an error will occurs when
initializing the clock. These ABIs are only used for X1000, and
I'm sure that no other devicetree out there is using these ABIs,
so we should be able to reorder them.
2.Clocks of LCD, OTG, EMC, EFUSE, OST, TCU are also added.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lkml.kernel.org/r/20200528031549.13846-7-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the clock bindings for the X1830 Soc from Ingenic.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lkml.kernel.org/r/20200528031549.13846-5-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This describes the bindings for a controller that generates master and bit
clocks for the I2S interface.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lkml.kernel.org/r/20200519224151.2074597-13-lkundrak@v3.sk
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On MMP2 the audio and GPU blocks are on separate power islands. On MMP3
the camera block's power is also controlled separately.
Add the numbers that we could use to refer to the power domains for
respective power islands from the device tree.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lkml.kernel.org/r/20200519224151.2074597-11-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We need to have clocks accessible via phandle to select them
as peripheral clock parent using assigned-clock-parents in DT.
Add support for PLLACK/PLLBCK/AUDIOPLLCK clocks where available.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lkml.kernel.org/r/fa39cc10dab8341ea4bc2b7152be9217b2cd34a5.1588630999.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Document the Agilex clock bindings, and add the clock header file. The
clock header is an enumeration of all the different clocks on the Agilex
platform.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lkml.kernel.org/r/20200512181647.5071-4-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Highlights:
- new boards :Beelink GT-King Pro (G12B SoC), Smartlabs SML-5442TW
(S905D), Hardkernel ODROID-C4 (SM1)
- audio: support for GX-family SoCs
- audio: internal DAC support
- use the new USB control driver for GXL and GXM
-----BEGIN PGP SIGNATURE-----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=JbXj
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: Amlogic updates for v5.8
Highlights:
- new boards :Beelink GT-King Pro (G12B SoC), Smartlabs SML-5442TW
(S905D), Hardkernel ODROID-C4 (SM1)
- audio: support for GX-family SoCs
- audio: internal DAC support
- use the new USB control driver for GXL and GXM
* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (33 commits)
arm64: dts: meson-g12b-gtking-pro: add initial device-tree
dt-bindings: arm: amlogic: add support for the Beelink GT-King Pro
arm64: dts: meson-g12b-gtking: add initial device-tree
dt-bindings: arm: amlogic: add support for the Beelink GT-King
arm64: dts: meson: convert ugoos-am6 to common w400 dtsi
arm64: dts: meson: add ethernet interrupt to wetek dtsi
arm64: dts: meson: add support for the Smartlabs SML-5442TW
dt-bindings: arm: amlogic: add support for the Smartlabs SML-5442TW
dt-bindings: add vendor prefix for Smartlabs LLC
arm64: dts: meson: g12: add internal DAC glue
arm64: dts: meson: g12: add internal DAC
arm64: dts: meson: libretech-pc: add internal DAC support
arm64: dts: meson: libretech-ac: add internal DAC support
arm64: dts: meson: libretech-cc: add internal DAC support
arm64: dts: meson: p230-q200: add internal DAC support
arm64: dts: meson: gxl: add acodec support
arm64: dts: meson-sm1: add support for Hardkernel ODROID-C4
dt-bindings: arm: amlogic: add odroid-c4 bindings
arm64: dts: meson-sm1: add cpu thermal nodes
arm64: dts: meson-g12b: move G12B thermal nodes to meson-g12b.dtsi
...
Link: https://lore.kernel.org/r/5ec6f56a.1c69fb81.fc5d5.9ca6@mx.google.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Optimize imx-scu driver to use one TX and one RX instead of four for
talking to SCU.
- Fix one possible message header corruption where the response is
longer than the request.
- Move System Control defines into dt-bindings header, so that DT can
use them as well.
- A couple of small fixups.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7IeuUUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5CpAf/VV2krqXlgTXA1Ppl+ivdGkx9ntwo
dVtZYNr65Z1iqp6yujW7cH/qulXfkaFanwDptq9ulBkG6uiyV06GCtBxpp3VhNOB
60uaS8RsieYmCz3e8j4kZkMCBthpD72wt0DxF1TlJu2d/cWfsM4/bMbrx0qYiT0V
J5FqcGH0xbe+E5YITdoPQbNxEig49q2P6BhkNLQelVQtVgM0lwSpDX3WRpCizch4
bbKSVYudV/rGGPM7ZYM53N+ngwKZurRbIf7br1QgA4ZlQxdCtADB6IRd2RsfrC8P
4BizRONfh46ogrnb9/P951RZu9H7VFRkTurnXdU+NcFK8HPYDGQmm7P2SQ==
=cJwM
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.8:
- Optimize imx-scu driver to use one TX and one RX instead of four for
talking to SCU.
- Fix one possible message header corruption where the response is
longer than the request.
- Move System Control defines into dt-bindings header, so that DT can
use them as well.
- A couple of small fixups.
* tag 'imx-drivers-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
firmware: imx: scu: Fix possible memory leak in imx_scu_probe()
dt-bindings: firmware: imx: Add more system controls and PM clock types
dt-bindings: firmware: imx: Move system control into dt-binding headfile
firmware: imx: scu: Fix corruption of header
firmware: imx-scu: Support one TX and one RX
soc: imx8m: No need to put node when of_find_compatible_node() failed
Link: https://lore.kernel.org/r/20200523032516.11016-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a V4L2 video capture driver for Tegra210.
-----BEGIN PGP SIGNATURE-----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=ZA0j
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.8-media' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
media: tegra: Changes for v5.8-rc1
This contains a V4L2 video capture driver for Tegra210.
* tag 'tegra-for-5.8-media' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
media: tegra-video: Do not enable COMPILE_TEST
MAINTAINERS: correct path in TEGRA VIDEO DRIVER
media: tegra-video: Make tegra210_video_formats static
MAINTAINERS: Add Tegra Video driver section
media: tegra-video: Add Tegra210 Video input driver
dt-bindings: i2c: tegra: Document Tegra210 VI I2C
dt-bindings: tegra: Add VI and CSI bindings
dt-bindings: cpufreq: Add binding for NVIDIA Tegra20/30
dt-bindings: memory: tegra: Add external memory controller binding for Tegra210
dt-bindings: clock: tegra: Remove PMC clock IDs
dt-bindings: clock: tegra: Add clock ID for CSI TPG clock
Link: https://lore.kernel.org/r/20200515145311.1580134-7-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a large set of cleanups, bug fixes, general improvements
and documentation fixes for the RPMH driver. It adds a debugfs mechanism
for inspecting Command DB. Socinfo got the "soc_id" attribute defines
and definitions for a various variants of MSM8939.
RPMH, RPMPD and RPMHPD where made possible to build as modules, but RPMH
had to be reverted due to a compilation issue when tracing is enabled.
RPMHPD gained power-domains for the SM8250 voltage corners.
The SCM driver gained fixes for two build warnings and the SMP2P had an
unnecessary error print removed.
-----BEGIN PGP SIGNATURE-----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=tkhb
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.8
This contains a large set of cleanups, bug fixes, general improvements
and documentation fixes for the RPMH driver. It adds a debugfs mechanism
for inspecting Command DB. Socinfo got the "soc_id" attribute defines
and definitions for a various variants of MSM8939.
RPMH, RPMPD and RPMHPD where made possible to build as modules, but RPMH
had to be reverted due to a compilation issue when tracing is enabled.
RPMHPD gained power-domains for the SM8250 voltage corners.
The SCM driver gained fixes for two build warnings and the SMP2P had an
unnecessary error print removed.
* tag 'qcom-drivers-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (42 commits)
Revert "soc: qcom: rpmh: Allow RPMH driver to be loaded as a module"
soc: qcom: rpmh-rsc: Remove the pm_lock
soc: qcom: rpmh-rsc: Simplify locking by eliminating the per-TCS lock
kernel/cpu_pm: Fix uninitted local in cpu_pm
soc: qcom: rpmh-rsc: We aren't notified of our own failure w/ NOTIFY_BAD
soc: qcom: rpmh-rsc: Correctly ignore CPU_CLUSTER_PM notifications
firmware: qcom_scm-legacy: Replace zero-length array with flexible-array
soc: qcom: rpmh-rsc: Timeout after 1 second in write_tcs_reg_sync()
soc: qcom: rpmh-rsc: Factor "tcs_reg_addr" and "tcs_cmd_addr" calculation
soc: qcom: socinfo: add msm8936/39 and apq8036/39 soc ids
soc: qcom: aoss: Add SM8250 compatible
soc: qcom: pdr: Remove impossible error condition
soc: qcom: rpmh: Dirt can only make you dirtier, not cleaner
soc: qcom: rpmhpd: Add SM8250 power domains
firmware: qcom_scm: fix bogous abuse of dma-direct internals
dt-bindings: soc: qcom: apr: Use generic node names for APR services
firmware: qcom_scm: Remove unneeded conversion to bool
soc: qcom: cmd-db: Properly endian swap the slv_id for debugfs
soc: qcom: cmd-db: Use 5 digits for printing address
soc: qcom: cmd-db: Cast sizeof() to int to silence field width warning
...
Link: https://lore.kernel.org/r/20200519052533.1250024-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This tag adds support for i.MX8MP and i.MX8MN SoCs to the i.MX7 reset
controller driver, extends the Hi6220 reset driver to support the AO
reset controller used to bring the Mali450 GPU out of reset, and adds
a define for the internal DAC reset line on Amlogic GXL SoCs.
-----BEGIN PGP SIGNATURE-----
iI4EABYIADYWIQRRO6F6WdpH1R0vGibVhaclGDdiwAUCXr6nvBgccGhpbGlwcC56
YWJlbEBnbWFpbC5jb20ACgkQ1YWnJRg3YsB63QEA8Rig0c9jN9LBDxVmqxB8dU/k
4fc3vMtuxbbrzmoD9rIA/ApMrQe77k/JW+hCSBrgCQWlvHInRncKwrEIhWk7ADkN
=BaS5
-----END PGP SIGNATURE-----
Merge tag 'reset-for-v5.8' of git://git.pengutronix.de/pza/linux into arm/drivers
Reset controller updates for v5.8
This tag adds support for i.MX8MP and i.MX8MN SoCs to the i.MX7 reset
controller driver, extends the Hi6220 reset driver to support the AO
reset controller used to bring the Mali450 GPU out of reset, and adds
a define for the internal DAC reset line on Amlogic GXL SoCs.
* tag 'reset-for-v5.8' of git://git.pengutronix.de/pza/linux:
reset: hi6220: Add support for AO reset controller
reset: imx7: Add support for i.MX8MP SoC
dt-bindings: reset: imx7: Document usage on i.MX8MP SoC
dt-bindings: reset: imx7: Add support for i.MX8MN
dt-bindings: reset: meson: add gxl internal dac reset
Link: https://lore.kernel.org/r/20200515143844.GA17201@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- support GX SoCs in the EE power-controller driver
-----BEGIN PGP SIGNATURE-----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=nn2j
-----END PGP SIGNATURE-----
Merge tag 'amlogic-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/drivers
soc: amlogic: driver updates for v5.8
- support GX SoCs in the EE power-controller driver
* tag 'amlogic-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
soc: amlogic: meson-ee-pwrc: add support for the Meson GX SoCs
soc: amlogic: meson-ee-pwrc: add support for Meson8/Meson8b/Meson8m2
dt-bindings: power: meson-ee-pwrc: add support for the Meson GX SoCs
dt-bindings: power: meson-ee-pwrc: add support for Meson8/8b/8m2
Link: https://lore.kernel.org/r/5ec6f570.1c69fb81.a3753.711b@mx.google.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
display controller and a new board using it, the Odroid Advance Go.
sdcard regulator for the rockpro64 and a lot of devicetree fixes
making the dt-binding check a lot happier.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl7F1N0QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgV34CAChtYhGGRGEr8WwGL3WG1f8z1nwEfxEGaMx
niLnchgR2kWRiPFV8SVHaNkcGj9+VkeA/F8mCrrKiPDPrsL+s5X6q2liAmEGnIWo
OvlfyuIJNaSjnVxwhdZABIQsjjeLZI2i0OWGmq47vGopWaNWDGW9wrPlRslPrf4N
AIww1TwjKYK8Et5ja3COwfSt1gn2/PwR09wTfQwCy7wi9At6UWOQsDmpyFbjuTgv
GmPcQJZa2YtQovSM5FrbhguCKSGFSukopqqrrxmfsvlkz+xmZyeHN6MMpdNnwBXe
Kf3VU2p6b+75YouuOcJAAueBj6b37/tvi7KK/MZszdG2pM85SL1z
=BL2H
-----END PGP SIGNATURE-----
Merge tag 'v5.8-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
New soc variant the rk3326 which is essentially a px30 with only one
display controller and a new board using it, the Odroid Advance Go.
sdcard regulator for the rockpro64 and a lot of devicetree fixes
making the dt-binding check a lot happier.
* tag 'v5.8-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (22 commits)
arm64: dts: rockchip: fix pinctrl-names for gpio-leds node on rk3326-odroid-go2
arm64: dts: rockchip: fix pd_tcpc0 and pd_tcpc1 node position on rk3399
arm64: dts: rockchip: add bus-width properties to mmc nodes for px30
arm64: dts: rockchip: remove disable-wp from rk3308-roc-cc emmc node
arm64: dts: rockchip: rename and label gpio-led subnodes
arm64: dts: rockchip: fix defines in pd_vio node for rk3399
arm64: dts: rockchip: fix &pinctrl phy sub nodename for rk3399-orangepi
arm64: dts: rockchip: fix rtl8211e nodename for rk3399-orangepi
arm64: dts: rockchip: fix &pinctrl phy sub nodename for rk3399-nanopi4
arm64: dts: rockchip: fix rtl8211e nodename for rk3399-nanopi4
arm64: dts: rockchip: fix rtl8211f nodename for rk3328 Beelink A1
arm64: dts: rockchip: fix phy nodename for rk3328
include: dt-bindings: rockchip: remove unused defines
arm64: dts: rockchip: replace RK_FUNC defines in rk3326-odroid-go2
arm64: dts: rockchip: Define the rockchip Video Decoder node on rk3399
arm64: dts: rockchip: remove #sound-dai-cells from &spdif node of rk3399-hugsun-x99.dts
arm64: dts: rockchip: remove #sound-dai-cells from &i2s1 node of rk3399-pinebook-pro.dts
arm64: dts: rockchip: add Odroid Advance Go
dt-bindings: Add binding for Hardkernel Odroid Go Advance
arm64: dts: rockchip: add core devicetree for rk3326
...
Link: https://lore.kernel.org/r/1970481.V9vR1fIhX2@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds bindings for the CSI TPG clock on Tegra210, moves various
clocks from the clock and reset controller to the PMC where their
controls really are, adds bindings for the external memory controller
and video capture controller on Tegra210, as well as CPU frequency
scaling on Tegra20 and Tegra30.
-----BEGIN PGP SIGNATURE-----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=sMK0
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.8-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v5.8-rc1
This adds bindings for the CSI TPG clock on Tegra210, moves various
clocks from the clock and reset controller to the PMC where their
controls really are, adds bindings for the external memory controller
and video capture controller on Tegra210, as well as CPU frequency
scaling on Tegra20 and Tegra30.
* tag 'tegra-for-5.8-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: i2c: tegra: Document Tegra210 VI I2C
dt-bindings: tegra: Add VI and CSI bindings
dt-bindings: cpufreq: Add binding for NVIDIA Tegra20/30
dt-bindings: memory: tegra: Add external memory controller binding for Tegra210
dt-bindings: clock: tegra: Remove PMC clock IDs
dt-bindings: clock: tegra: Add clock ID for CSI TPG clock
Link: https://lore.kernel.org/r/20200515145311.1580134-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Initial support for the Renesas RZ/G1H SoC on the iWave RainboW
Qseven SOM (G21M) and board (G21D),
- Support for the AISTARVISION MIPI Adapter V2.1 camera board on the
Silicon Linux EK874 RZ/G2E evaluation kit.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXr5g8QAKCRCKwlD9ZEnx
cDusAQD4SCmyY0MZZNWQhkhu2ics2wYpKItw4Y7E4fl9XUlXkQEAyyN11vVNoteX
7KvNX7/9eXpberlcx4H6szPQsOzWzwM=
=2KDk
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.8 (take two)
- Initial support for the Renesas RZ/G1H SoC on the iWave RainboW
Qseven SOM (G21M) and board (G21D),
- Support for the AISTARVISION MIPI Adapter V2.1 camera board on the
Silicon Linux EK874 RZ/G2E evaluation kit.
* tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a774c0-cat874: Add support for AISTARVISION MIPI Adapter V2.1
ARM: dts: r8a7742: Add GPIO nodes
ARM: dts: r8a7742: Add [H]SCIF{A|B} support
ARM: dts: r8a7742: Add IRQC support
ARM: dts: r8a7742-iwg21d-q7: Add iWave G21D-Q7 board based on RZ/G1H
ARM: dts: r8a7742-iwg21m: Add iWave RZ/G1H Qseven SOM
ARM: dts: r8a7742: Initial SoC device tree
clk: renesas: Add r8a7742 CPG Core Clock Definitions
dt-bindings: power: rcar-sysc: Add r8a7742 power domain index macros
Link: https://lore.kernel.org/r/20200515100547.14671-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use imx8m_clk_hw_composite_core to simpliy clks that belong to
core clk slice.
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Inspried from
commit e8688fe8df ("clk: imx8mn: Define gates for pll1/2 fixed dividers")
On imx8mp there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate. Only one of these gates (the one "dividing" by
one) is currently defined and it's incorrectly set as the parent of all
the fixed-factor dividers.
Add the other 8 gates to the clock tree between sys_pll1/2_bypass and
the fixed dividers.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The power domains on the GX SoCs are very similar to G12A. The only
known differences so far are:
- The GX SoCs do not have the HHI_VPU_MEM_PD_REG2 register (for the
VPU power-domain)
- The GX SoCs have an additional reset line called "dvin"
Add a new compatible string and adjust the reset line expectations for
these SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200515204709.1505498-3-martin.blumenstingl@googlemail.com
The power domains on the 32-bit Meson8/Meson8b/Meson8m2 SoCs are very
similar to what G12A still uses. The (known) differences are:
- Meson8 doesn't use any reset lines at all
- Meson8b and Meson8m2 use the same reset lines, which are different
from what the 64-bit SoCs use
- there is no "vapb" clock on the older SoCs
- amlogic,ao-sysctrl cannot point to the whole AO sysctrl region but
only the power management related registers
Add a new compatible string and adjust clock and reset line expectations
for each SoC.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200515204709.1505498-2-martin.blumenstingl@googlemail.com
Stephen Boyd
Damien Le Moal
Claudiu Beznea
Eugen Hristev
Linus Torvalds
Zong Li
Vinod Koul
Daniel Palmer
Arnd Bergmann
Manivannan Sadhasivam
Michael Walle
Thierry Reding
周琰杰 (Zhou Yanjie)
Adam Ward
Georgi Djakov
Weiyi Lu
Enric Balletbo i Serra
Dmitry Osipenko
Neil Armstrong
Thara Gopinath
Joakim Zhang
Tony Lindgren
Álvaro Fernández Rojas
Srinivas Kandagatla
Taniya Das
Badhri Jagan Sridharan
Nicolin Chen
Alexandru Ardelean
Stephan Gerhold
Jun Nie
Konrad Dybcio
Dong Aisheng
Jonathan Marek
Fabien Parent
V Sujith Kumar Reddy
Olof Johansson
Greg Kroah-Hartman
Roger Quadros
Peng Fan
Sai Krishna Potthuri
Drew Fustini
Tero Kristo
David Heidelberg
Swapnil Jakhade
Sylwester Nawrocki
Yoshihiro Shimoda
Sibi Sankar
Mike Tipton
Jacky Bai
Zhiyong Tao
Gene Chen
Yangtao Li
Krzysztof Kozlowski
Nicolas Saenz Julienne
Ajit Pandey
Dennis YC Hsieh
Pavel Machek
Lars Povlsen
Randy Dunlap
Thomas Gleixner
Hanks Chen
Jonathan Cameron
Cristian Ciocaltea
Sivaprakash Murugesan
Artur Rojek
Alexander A. Klimov
Kishon Vijay Abraham I
Laurent Pinchart
Dan Murphy
Marian-Cristian Rotariu
Chao Hao
Mark Brown
Anand K Mistry
Anurag Kumar Vulisha
Andrey Smirnov
Adam Ford
Vincent Knecht
Dinh Nguyen
Dmitry Shmidt
Jishnu Prakash
Serge Semin
Mars Cheng
Jeffrey Hugo
Lubomir Rintel
Chunyan Zhang
Michał Mirosław
Rahul Tanwar
Martin Blumenstingl