Pull input fixes from Dmitry Torokhov:
- we are reverting patch that was switched touchpad on Lenovo T460P
over to native RMI because on these boxes BIOS messes up with SMBus
controller state. We might re-enable it later once SMBus issue is
resolved
- disabling interrupts in matrix_keypad driver was racy
- mms114 now has SPDX header and matching MODULE_LICENSE
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - Lenovo Thinkpad T460p devices should use RMI"
Input: matrix_keypad - fix race when disabling interrupts
Input: mms114 - add SPDX identifier
Input: mms114 - fix license module information
This reverts commit 4828296982 which
caused the following issues:
1. On T460p with BIOS version 2.22 touchpad and trackpoint stop working
after suspend-resume cycle. Due to strange state of the device another
suspend is impossible.
The following dmesg errors can be observed:
thinkpad_acpi: EC reports that Thermal Table has changed
rmi4_smbus 7-002c: failed to get SMBus version number!
rmi4_physical rmi4-00: rmi_driver_reset_handler: Failed to read current IRQ mask.
rmi4_f01 rmi4-00.fn01: Failed to restore normal operation: -16.
rmi4_f01 rmi4-00.fn01: Resume failed with code -16.
rmi4_physical rmi4-00: Failed to suspend functions: -16
rmi4_smbus 7-002c: Failed to resume device: -16
PM: resume devices took 0.640 seconds
rmi4_f03 rmi4-00.fn03: rmi_f03_pt_write: Failed to write to F03 TX register (-16).
rmi4_physical rmi4-00: rmi_driver_clear_irq_bits: Failed to change enabled interrupts!
rmi4_physical rmi4-00: rmi_driver_set_irq_bits: Failed to change enabled interrupts!
psmouse: probe of serio3 failed with error -1
2. On another T460p with BIOS version 2.15 two finger scrolling gesture
on the touchpad stops working after suspend-resume cycle (about 75%
reproducibility, when it still works, the scrolling gesture becomes
laggy). Nothing suspicious appears in the dmesg.
Analysis form Richard Schütz:
"RMI is unreliable on the ThinkPad T460p because the device is affected
by the firmware behavior addressed in a7ae81952c ("i2c: i801: Allow
ACPI SystemIO OpRegion to conflict with PCI BAR")."
The affected devices often show:
i801_smbus 0000:00:1f.4: BIOS is accessing SMBus registers
i801_smbus 0000:00:1f.4: Driver SMBus register access inhibited
Reported-by: Richard Schütz <rschuetz@uni-koblenz.de>
Signed-off-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Tested-by: Martin Peres <martin.peres@linux.intel.com>
Tested-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If matrix_keypad_stop() is executing and the keypad interrupt is triggered,
disable_row_irqs() may be called by both matrix_keypad_interrupt() and
matrix_keypad_stop() at the same time, causing interrupts to be disabled
twice and the keypad being "stuck" after resuming.
Take lock when setting keypad->stopped to ensure that ISR will not race
with matrix_keypad_stop() disabling interrupts.
Signed-off-by: Zhang Bo <zbsdta@126.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace the original license statement with the SPDX identifier.
Add also one line of description as recommended by the COPYING
file.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver has been released with GNU Public License v2 as stated
in the header, but the module license information has been tagged
as "GPL" (GNU Public License v2 or later).
Fix the module license information so that it matches the one in
the header as "GPL v2".
Fixes: 07b8481d4a ("Input: add MELFAS mms114 touchscreen driver")
Reported-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer updates from Dmitry Torokhov:
- evdev interface has been adjusted to extend the life of timestamps on
32 bit systems to the year of 2108
- Synaptics RMI4 driver's PS/2 guest handling ha beed updated to
improve chances of detecting trackpoints on the pass-through port
- mms114 touchcsreen controller driver has been updated to support
generic device properties and work with mms152 cntrollers
- Goodix driver now supports generic touchscreen properties
- couple of drivers for AVR32 architecture are gone as the architecture
support has been removed from the kernel
- gpio-tilt driver has been removed as there are no mainline users and
the driver itself is using legacy APIs and relies on platform data
- MODULE_LINECSE/MODULE_VERSION cleanups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: goodix - use generic touchscreen_properties
Input: mms114 - fix typo in definition
Input: mms114 - use BIT() macro instead of explicit shifting
Input: mms114 - replace mdelay with msleep
Input: mms114 - add support for mms152
Input: mms114 - drop platform data and use generic APIs
Input: mms114 - mark as direct input device
Input: mms114 - do not clobber interrupt trigger
Input: edt-ft5x06 - fix error handling for factory mode on non-M06
Input: stmfts - set IRQ_NOAUTOEN to the irq flag
Input: auo-pixcir-ts - delete an unnecessary return statement
Input: auo-pixcir-ts - remove custom log for a failed memory allocation
Input: da9052_tsi - remove unused mutex
Input: docs - use PROPERTY_ENTRY_U32() directly
Input: synaptics-rmi4 - log when we create a guest serio port
Input: synaptics-rmi4 - unmask F03 interrupts when port is opened
Input: synaptics-rmi4 - do not delete interrupt memory too early
Input: ad7877 - use managed resource allocations
Input: stmfts,s6sy671 - add SPDX identifier
Input: remove atmel-wm97xx touchscreen driver
...
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
Use touchscreen_properties structure instead of implementing all
properties by our own. It allows us to reuse generic code for parsing
device-tree properties (which was implemented manually in the driver for
now). Additionally, it allows us to report events using generic
touchscreen_report_pos(), which automatically handles inverted and
swapped axes.
This fixes the issue with the custom code incorrectly handling case where
ts->inverted_x and ts->swapped_x_y were true, but ts->inverted_y was
false. Assuming we have 720x1280 touch panel, ts->abs_x_max == 1279 and
ts->abs_y_max == 719 (because we inverted that in goodix_read_config()).
Now let's assume that we received event from (0:0) position (in touch
panel original coordinates). In function goodix_ts_report_touch() we
calculate input_x as 1279, but after swapping input_y takes that value
(which is more that maximum 719 value reported during initialization).
Note that since touchscreen coordinates are 0-indexed, we now report
touchscreen range as (0:size-1).
Developed and tested on custom DT-based device with gt1151 touch
panel.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
[dtor: fix endianness annotation reported by sparse, handle errors when
initializing MT slots]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
200 milliseconds is a very long time to keep the CPU busy looping.
Use msleep instead.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MMS152 has no configuration registers, but the packet format used in
interrupts is identical to mms114.
Signed-off-by: Simon Shields <simon@lineageos.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MMS114 platform data has no in-tree users, so drop it.
Switch to using the standard touchscreen properties via
touchscreen_parse_properties(), and move the old DT parsing code
to use device_property_*() APIs.
Finally, use touchscreen_report_pos to report x/y coordinates
and drop the custom x/y inversion code.
Signed-off-by: Simon Shields <simon@lineageos.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
mms14 is a touchscreen and thus a direct input device; let's mark it
as such. This also allows us to drop some initialization code as
input_init_mt_slots() will do that for us.
Also add error handling for input_mt_init_slots().
Reviewed-by: Simon Shields <simon@lineageos.org>
Tested-by: Simon Shields <simon@lineageos.org>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"The main item is that we try to better handle the newer trackpoints on
Lenovo devices that are now being produced by Elan/ALPS/NXP and only
implement a small subset of the original IBM trackpoint controls"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics_rmi4 - use devm_device_add_group() for attributes in F01"
Input: trackpoint - only expose supported controls for Elan, ALPS and NXP
Input: trackpoint - force 3 buttons if 0 button is reported
Input: xpad - add support for PDP Xbox One controllers
Input: stmfts,s6sy671 - add SPDX identifier
Since the sysfs attribute hangs off the RMI bus, which doesn't go away during
firmware flash, it needs to be explicitly removed, otherwise we would try and
register the same attribute twice.
This reverts commit 36a44af5c1.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When attempting enter factory mode on firmware that does not support it,
we'd error out, but leave the device with interrupts disabled, and thus
touch not working. Fix it by moving the check before we disable
interrupts/allocate memory for debug buffers.
Fixes: fd335ab04b ("Input: edt-ft5x06 - add support for M09 firmware version")
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The interrupt is requested before the device is powered on and
it's value in some cases cannot be reliable. It happens on some
devices that an interrupt is generated as soon as requested
before having the chance to disable the irq.
Set the irq flag as IRQ_NOAUTOEN before requesting it.
This patch mutes the error:
stmfts 2-0049: failed to read events: -11
received sometimes during boot time.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The script "checkpatch.pl" pointed information out like the following:
WARNING: void function return statements are not generally useful
Thus remove such a statement in the affected function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To ease analyzing boot behavior from logs, let's log when we are about to
register the pass-through serio port.
Also, let's drop "Synaptics" prefix from the port name, as RMI4 is good
enough indicator already, and having the prefix means that the name does
not fit into serio->name field. While at it move from hard-coded seio->phys
to one mentioning the sensor ID (such as "rmi4-00.fn03/serio0").
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently we register the pass-through serio port when we probe the F03 RMI
function, and then, in sensor configure phase, we unmask interrupts.
Unfortunately this is too late, as other drivers are free probe devices
attached to the serio port as soon as it is probed. Because interrupts are
masked, the IO times out, which may result in not being able to detect
trackpoints on the pass-through port.
To fix the issue we implement open() and close() methods for the
pass-through serio port and unmask interrupts from there. We also move
creation of the pass-through port form probe to configure stage, as RMI
driver does not enable transport interrupt until all functions are probed
(we should change this, but this is a separate topic).
We also try to clear the pending data before unmasking interrupts, because
some devices like to spam the system with multiple 0xaa 0x00 announcements,
which may interfere with us trying to query ID of the device.
Fixes: c5e8848fc9 ("Input: synaptics-rmi4 - add support for F03")
Cc: stable@vger.kernel.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We want to free memory reserved for interrupt mask handling only after we
free functions, as function drivers might want to mask interrupts. This is
needed for the followup patch to the F03 that would implement unmasking and
masking interrupts from the serio pass-through port open() and close()
methods.
Cc: stable@vger.kernel.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use managed resource allocations to simplify error handling during
probing failure and module exiting.
With this all the goto labels in the probe function together with
the cleanups in the remove function are unnecessary, therefore
removed.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace the original license statement with the SPDX identifier.
Update also the copyright owner adding myself as co-owner of the
copyright.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The newer trackpoints from ALPS, Elan and NXP implement a very limited
subset of extended commands and controls that the original trackpoints
implemented, so we should not be exposing not working controls in sysfs.
The newer trackpoints also do not implement "Power On Reset" or "Read
Extended Button Status", so we should not be using these commands during
initialization.
While we are at it, let's change "unsigned char" to u8 for byte data or
bool for booleans and use better suited error codes instead of -1.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Lenovo introduced trackpoint compatible sticks with minimum PS/2 commands.
They supposed to reply with 0x02, 0x03, or 0x04 in response to the
"Read Extended ID" command, so we would know not to try certain extended
commands. Unfortunately even some trackpoints reporting the original IBM
version (0x01 firmware 0x0e) now respond with incorrect data to the "Get
Extended Buttons" command:
thinkpad_acpi: ThinkPad BIOS R0DET87W (1.87 ), EC unknown
thinkpad_acpi: Lenovo ThinkPad E470, model 20H1004SGE
psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 0/0
Since there are no trackpoints without buttons, let's assume the trackpoint
has 3 buttons when we get 0 response to the extended buttons query.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196253
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adds support for the current lineup of Xbox One controllers from PDP
(Performance Designed Products). These controllers are very picky with
their initialization sequence and require an additional 2 packets before
they send any input reports.
Signed-off-by: Mark Furneaux <mark@furneaux.ca>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace the original license statement with the SPDX identifier.
Update also the copyright owner adding myself as co-owner of the
copyright.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- a fix for use-after-free in Synaptics RMI4 driver
- correction to multitouch contact tracking on certain ALPS touchpads
(which got broken when we tried to fix the 2-finger scrolling)
- touchpad on Lenovo T640p is switched over to SMbus/RMI
- a few device node refcount fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - prevent UAF reported by KASAN
Input: ALPS - fix multi-touch decoding on SS4 plus touchpads
Input: synaptics - Lenovo Thinkpad T460p devices should use RMI
Input: of_touchscreen - add MODULE_LICENSE
Input: 88pm860x-ts - fix child-node lookup
Input: twl6040-vibra - fix child-node lookup
Input: twl4030-vibra - fix sibling-node lookup
Since AVR32 arch is gone, atmel-wm97xx driver is useless. In theory it
could have been rewritten to work with AT91 devices, but the driver is from
the platform data era, and a bit hard coded to work on AVR32 hardware
variant of the AC97C peripheral, so let's remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The variable pwr_cmd is being assigned to cyapa->suspend_power_mode
twice, once during the declaration and once after taking an
interruptible mutex lock. Remove the redundant first assignment
since the value is never read and it is outside the mutex lock.
Cleans up clang warning:
drivers/input/mouse/cyapa.c:743:5: warning: Value stored to 'pwr_cmd'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Inline macro for MODULE_LICENSE to make the license information easy to
find, eg with grep. Inline the other module-related macros at the same
time.
A simplified version of the semantic patch for the MODULE_LICENSE
case is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s@
identifier i; expression e;
@@
@@
declarer name MODULE_LICENSE;
identifier s.i;
expression s.e;
@@
MODULE_LICENSE(
- i
+ e
);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[dtor: added a couple of drivers missed by the script, removed a few unused
DRIVER_VERSION macros]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the remaining few input drivers that still used it
(input-polldev and sparse-keymap).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the misc input drivers. Along with this, some
DRIVER_VERSION macros were removed as they are also pointless.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the touchscreen drivers. Along with this, some
DRV_VERSION macros were removed as they are also pointless.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the elan_i2c mouse driver. Now that this is gone, the
ELAN_DRIVER_VERSION define was also removed as it was pointless.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MODULE_VERSION is useless for in-kernel drivers, so remove the use of it
in the pmic8xxx-keyboard driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the rmi4 drivers. Now that this is gone, the
RMI_DRIVER_VERSION macro was also removed as it was pointless.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.
This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference. For some of these drivers, the #define is just a
few lines above the MODULE_LICENSE() line, which is extra pointless.
Reported-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() resets the ABS_X/Y fuzz to 0 and expects the driver
to call input_mt_report_pointer_emulation(). That is based on the MT
position bits which are already defuzzed - hence a fuzz of 0.
In the case of synaptics semi-mt devices, we report the ABS_X/Y axes
manually. This results in the MT position being defuzzed but the
single-touch emulation missing that defuzzing.
Work around this by re-initializing the ABS_X/Y axes after the MT axis to
get the same fuzz value back.
https://bugs.freedesktop.org/show_bug.cgi?id=104533
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When Synaptics protocol is disabled, we still need to try and detect the
hardware, so we can switch to SMBus device if SMbus is detected, or we know
that it is Synaptics device and reset it properly for the bare PS/2
protocol.
Fixes: c378b5119e ("Input: psmouse - factor out common protocol probing code")
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should not try to do any i2c transfers before the controller is
resumed (which happens before our resume method gets called).
So we need to disable our IRQ while suspended to enforce this. The
code paths for devices with GPIOs for the int and reset pins already
disable the IRQ the through goodix_free_irq().
This commit also disables the IRQ while suspended for devices without
GPIOs for the int and reset pins.
This fixes the i2c bus sometimes getting stuck after a suspend/resume
causing the touchscreen to sometimes not work after a suspend/resume.
This has been tested on a GPD pocked device.
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://www.reddit.com/r/GPDPocket/comments/7niut2/fix_for_broken_touch_after_resume_all_linux/
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds
Arkadiusz Hiler
Zhang Bo
Andi Shyti
Dmitry Torokhov
Marcin Niestroj
Simon Shields
Nick Dyer
Markus Elfring
Marcus Folkesson
Andi Shyti
Aaron Ma
Mark Furneaux
Corentin Labbe
Nick Desaulniers
Colin Ian King
Julia Lawall
Greg Kroah-Hartman
Peter Hutterer
Hans de Goede