When the xen block frontend driver is built as a module the module load
is only synchronous up to the point where the frontend and the backend
become connected rather than when the disk is added.
This means that there can be a race on boot between loading the module and
loading the dm-* modules and doing the scan for LVM physical volumes (all
in the initrd). In the failure case the disk is not present until after the
scan for physical volumes is complete.
Taken from:
http://xenbits.xensource.com/linux-2.6.18-xen.hg?rev/11483a00c017
Signed-off-by: Christian Limpach <Christian.Limpach@xensource.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Frontends are expected to write their protocol ABI to xenstore. Since
the protocol ABI defaults to the backend's native ABI, things work
fine without that as long as the frontend's native ABI is identical to
the backend's native ABI. This is not the case for xen-blkfront
running 32-on-64, because its ABI differs between 32 and 64 bit, and
thus needs this fix.
Based on http://xenbits.xensource.com/xen-unstable.hg?rev/c545932a18f3
and http://xenbits.xensource.com/xen-unstable.hg?rev/ffe52263b430 by
Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On xen/ia64 and xen/powerpc hypercall arguments are passed by pseudo
physical address (guest physical address) so that it's necessary to
convert from virtual address into pseudo physical address. The frame
work is called xencomm.
Import arch generic part of xencomm.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
split out x86 specific part from grant-table.c and
allow ia64/xen specific initialization.
ia64/xen grant table is based on pseudo physical address
(guest physical address) unlike x86/xen. On ia64 init_mm
doesn't map identity straight mapped area.
ia64/xen specific grant table initialization is necessary.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Don't use alloc_vm_area()/free_vm_area() directly, instead define
xen_alloc_vm_area()/xen_free_vm_area() and use them.
alloc_vm_area()/free_vm_area() are used to allocate/free area which
are for grant table mapping. Xen/x86 grant table is based on virtual
address so that alloc_vm_area()/free_vm_area() are suitable.
On the other hand Xen/ia64 (and Xen/powerpc) grant table is based on
pseudo physical address (guest physical address) so that allocation
should be done differently.
The original version of xenified Linux/IA64 have its own
allocate_vm_area()/free_vm_area() definitions which don't allocate vm area
contradictory to those names.
Now vanilla Linux already has its definitions so that it's impossible
to have IA64 definitions of allocate_vm_area()/free_vm_area().
Instead introduce xen_allocate_vm_area()/xen_free_vm_area() and use them.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The definitions in include/asm/xen/page.h are arch specific.
ia64/xen wants to define its own version. So move them to arch specific
directory and keep include/xen/page.h in order not to break compilation.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Define resend_irq_on_evtchn() which ia64/xen uses.
Although it isn't used by current x86/xen code, it's arch generic
so that put it into common code.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove x86 dependency in drivers/xen/events.c for ia64/xen support
introducing include/asm/xen/events.h.
Introduce xen_irqs_disabled() to hide regs->flags
Introduce xen_do_IRQ() to hide regs->orig_ax.
make enum ipi_vector definition arch specific. ia64/xen needs four vectors.
Add one rmb() because on ia64 xchg() isn't barrier.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
move arch/x86/xen/events.c undedr drivers/xen to share codes
with x86 and ia64. And minor adjustment to compile.
ia64/xen also uses events.c
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add xen handles realted definitions for xen vcpu which ia64/xen needs.
Pointer argumsnts for ia64/xen hypercall are passed in pseudo physical
address (guest physical address) so that it is required to convert
guest kernel virtual address into pseudo physical address.
The xen guest handle represents such arguments.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add xen handles realted definitions for grant table which ia64/xen
needs.
Pointer argumsnts for ia64/xen hypercall are passed in pseudo physical
address (guest physical address) so that it is required to convert
guest kernel virtual address into pseudo physical address right before
issuing hypercall.
The xen guest handle represents such arguments.
Define necessary handles and helper functions.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add xen VIRQ numbers defined for arch specific use.
ia64/xen domU uses VIRQ_ARCH_0 for virtual itc timer.
Although all those constants aren't used yet by ia64
at this moment, add all arch specific VIRQ numbers.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add xen hypercall numbers defined for arch specific use.
ia64/xen domU uses __HYPERVISOR_arch_1 to manipulate paravirtualized
IOSAPIC. Although all those constants aren't used yet by IA64 at this
moment, add all arch specific hypercall numbers.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All pagetables need fundamentally the same setup and destruction, so
just use the same code for everything.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make KERNEL_PGD_PTRS common, as previously it was only being defined
for 32-bit.
There are a couple of follow-on changes from this:
- KERNEL_PGD_PTRS was being defined in terms of USER_PGD_PTRS. The
definition of USER_PGD_PTRS doesn't really make much sense on x86-64,
since it can have two different user address-space configurations.
I renamed USER_PGD_PTRS to KERNEL_PGD_BOUNDARY, which is meaningful
for all of 32/32, 32/64 and 64/64 process configurations.
- USER_PTRS_PER_PGD was also defined and was being used for similar
purposes. Converting its users to KERNEL_PGD_BOUNDARY left it
completely unused, and so I removed it.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Zach Amsden <zach@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Xen's pte operations on mfns can be unified like the kernel's pfn operations.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Turn paravirt stubs into inline functions, so that the arguments are
still typechecked.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename (alloc|release)_(pt|pd) to pte/pmd to explicitly match the name
of the appropriate pagetable level structure.
[ x86.git merge work by Mark McLoughlin <markmc@redhat.com> ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Common definitions for 3-level pagetable functions.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Common definitions for 2-level pagetable functions.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add a common arch/x86/mm/pgtable.c file for common pagetable functions.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert asm-x86/pgalloc_64.h from macros into functions (#include hell
prevents __*_free_tlb from being inline, but they're probably a bit
big to inline anyway).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
x86 has ioremap_wc for wc remap. Also introduce a generic ioremap_wc
aliased to ioremap_uc so that drivers can use this interface transparently.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce phys_mem_access_prot_allowed(), which checks whether the mapping
is possible, without any conflicts and returns success or failure based on that.
phys_mem_access_prot() by itself does not allow failure case. This ability
to return error is needed for PAT where we may have aliasing conflicts.
x86 setup __HAVE_PHYS_MEM_ACCESS_PROT and move x86 specific code out of
/dev/mem into arch specific area.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add xlate and unxlate around /dev/mem read/write. This sets up the mapping
that can be used for /dev/mem read and write without aliasing worries.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch introduces a restriction on /dev/mem: Only non-memory can be
read or written unless the newly introduced config option is set.
The X server needs access to /dev/mem for the PCI space, but it doesn't need
access to memory; both the file permissions and SELinux permissions of /dev/mem
just make X effectively super-super powerful. With the exception of the
BIOS area, there's just no valid app that uses /dev/mem on actual memory.
Other popular users of /dev/mem are rootkits and the like.
(note: mmap access of memory via /dev/mem was already not allowed since
a really long time)
People who want to use /dev/mem for kernel debugging can enable the config
option.
The restrictions of this patch have been in the Fedora and RHEL kernels for
at least 4 years without any problems.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (80 commits)
SUNRPC: Invalidate the RPCSEC_GSS session if the server dropped the request
make nfs_automount_list static
NFS: remove duplicate flags assignment from nfs_validate_mount_data
NFS - fix potential NULL pointer dereference v2
SUNRPC: Don't change the RPCSEC_GSS context on a credential that is in use
SUNRPC: Fix a race in gss_refresh_upcall()
SUNRPC: Don't disconnect more than once if retransmitting NFSv4 requests
SUNRPC: Remove the unused export of xprt_force_disconnect
SUNRPC: remove XS_SENDMSG_RETRY
SUNRPC: Protect creds against early garbage collection
NFSv4: Attempt to use machine credentials in SETCLIENTID calls
NFSv4: Reintroduce machine creds
NFSv4: Don't use cred->cr_ops->cr_name in nfs4_proc_setclientid()
nfs: fix printout of multiword bitfields
nfs: return negative error value from nfs{,4}_stat_to_errno
NLM/lockd: Ensure client locking calls use correct credentials
NFS: Remove the buggy lock-if-signalled case from do_setlk()
NLM/lockd: Fix a race when cancelling a blocking lock
NLM/lockd: Ensure that nlmclnt_cancel() returns results of the CANCEL call
NLM: Remove the signal masking in nlmclnt_proc/nlmclnt_cancel
...
* 'for-linus' of git://linux-nfs.org/~bfields/linux: (52 commits)
knfsd: clear both setuid and setgid whenever a chown is done
knfsd: get rid of imode variable in nfsd_setattr
SUNRPC: Use unsigned loop and array index in svc_init_buffer()
SUNRPC: Use unsigned index when looping over arrays
SUNRPC: Update RPC server's TCP record marker decoder
SUNRPC: RPC server still uses 2.4 method for disabling TCP Nagle
NLM: don't let lockd exit on unexpected svc_recv errors (try #2)
NFS: don't let nfs_callback_svc exit on unexpected svc_recv errors (try #2)
Use a zero sized array for raw field in struct fid
nfsd: use static memory for callback program and stats
SUNRPC: remove svc_create_thread()
nfsd: fix comment
lockd: Fix stale nlmsvc_unlink_block comment
NFSD: Strip __KERNEL__ testing from unexported header files.
sunrpc: make token header values less confusing
gss_krb5: consistently use unsigned for seqnum
NFSD: Remove NFSv4 dependency on NFSv3
SUNRPC: Remove PROC_FS dependency
NFSD: Use "depends on" for PROC_FS dependency
nfsd: move most of fh_verify to separate function
...
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (452 commits)
V4L/DVB (7731): tuner-xc2028: fix signal strength calculus
V4L/DVB (7730): tuner-xc2028: Fix SCODE load for MTS firmwares
V4L/DVB (7729): Fix VIDIOCGAP corruption in ivtv
V4L/DVB (7728): tea5761: bugzilla #10462: tea5761 autodetection code were broken
V4L/DVB (7726): cx23885: Enable cx23417 support on the HVR1800
V4L/DVB (7725): cx23885: Add generic cx23417 hardware encoder support
V4L/DVB (7723): pvrusb2: Clean up input selection list generation in V4L interface
V4L/DVB (7722): pvrusb2: Implement FM radio support for Gotview USB2.0 DVD 2
V4L/DVB (7721): pvrusb2: Restructure cx23416 firmware loading to have a common exit point
V4L/DVB (7720): pvrusb2: Fix bad error code on cx23416 firmware load failure
V4L/DVB (7719): pvrusb2: Implement input selection enforcement
V4L/DVB (7718): pvrusb2-dvb: update Kbuild selections
V4L/DVB (7717): pvrusb2-dvb: add DVB-T support for Hauppauge pvrusb2 model 73xxx
V4L/DVB (7716): pvrusb2: clean up global functions
V4L/DVB (7715): pvrusb2: Clean out all use of __FUNCTION__
V4L/DVB (7714): pvrusb2: Fix hang on module removal
V4L/DVB (7713): pvrusb2: Implement cleaner DVB kernel thread shutdown
V4L/DVB (7712): pvrusb2: Close connect/disconnect race
V4L/DVB (7711): pvrusb2: Fix race on module unload
V4L/DVB (7710): pvrusb2: Implement critical digital streaming quirk for onair devices
...
videobuf-dvb were still using a function that were videobuf-dma-sg
dependent. This patch creates a generic handler for this function. This
way, videobuf-dvb can now work with all videobuf implementations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The adapter_nr module options can be used to allocate static adapter
numbers on a driver level. It avoids problems with changing DVB apapter
numbers after warm/cold boot or device unplugging and repluging.
Each driver holds DVB_MAX_ADAPTER long array of the preferred order of
adapter numbers.
options dvb-usb-dib0700 adapter_nr=7,6,5,4,3,2,1,0 would result in a
reversed allocation of adapter numbers.
With adapter_nr=2,5 it tries first to get adapter number 2 and 5. If
both are already in use it will allocate the lowest free adapter number.
Signed-off-by: Janne Grunau <janne-dvb@grunau.be>
Acked-by: Hermann Pitton <hermann.pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch adds complete remote control support for Powercolor Real
Angel 330.
Signed-off-by: Daniel Fraga <fragabr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All drivers should provide a spinlock to be used in videobuf operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Reviewed-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Function pointers and the driver owner are not expected to change
throughout soc-camera host's life. Extract them into an operations struct.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a waitqueue to wait on when there are no buffers in the buffer queue.
DQBUF waits on this queue without holding vb_lock to allow a QBUF to happen.
Once a buffer has been queued we recheck that the queue is still streaming and
wait on the new buffer's waitqueue while holding the vb_lock. The driver
should come along in a timely manner and put the buffer into its next state
finishing the DQBUF.
By implementing this waitqueue it also brings the videobuf DQBUF up to spec and
it now blocks on O_NONBLOCK even when no buffers have been queued via QBUF:
"By default VIDIOC_DQBUF blocks when no buffer is in the outgoing queue."
- V4L2 spec
Signed-off-by: Brandon Philips <bphilips@suse.de>
CC: Trent Piepho <xyzzy@speakeasy.org>
CC: Carl Karsten <carl@personnelware.com>
CC: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Define a pre-defined control ID for color killer functionality.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Define a pre-defined control ID for chroma automatic gain control.
Signed-off-by: "Frej Drejhammar <frej.drejhammar@gmail.com>"
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TUNER_PHILIPS_ATSC is an ambiguous name for a tuner. Rename it to
TUNER_PHILIPS_FCV1236D to be more descriptive.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make the dev member of the struct videobuf_queue of type "struct device *"
to avoid future problems. Also change the prototype of the
videobuf_queue_core_init() function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add entry points used for digital tuning via the dvb_frontend.
Share state data between multiple instances of the driver for hybrid
tuners.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Improve hardware parameter negotiation between the camera host driver and
camera drivers. Parameters like horizontal and vertical synchronisation,
pixel clock polarity shall be set depending on capabilities of the
parties.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently (in linux-2.6.24, but linux-dvb hg looks similar), the
dmx_output_t in the dmx_pes_filter_params decides two things: whether
output is sent to demux0 or dvr0 (in dmxdev.c:dvb_dmxdev_ts_callback),
*and* whether to depacketise TS (in dmxdev.c:dvb_dmxdev_filter_start).
As it stands, those two things can't be set independently: output
destined for demux0 is depacketised, output for dvr0 isn't.
This is what you want for capturing multiple audio streams from the same
multiplex simultaneously: open demux0 several times and send
depacketised output there. And capturing a single video stream is fine
not what you want: you want multi-open (so demux0, not dvr0), but you
want the TS nature preserved (because that's what you want on output, as
you're going to re-multiplex it with the audio).
At least one existing solution -- GStreamer -- sends all its streams
simultaneously via dvr0 and demuxes again in userland, but it seems a
bit of a shame to pick out all the PIDs in kernel, stick them back
together in kernel, and send them to userland only to get unpicked
again, when the alternative is such a small API addition.
The attached patch adds a new value for dmx_output_t:
DMX_OUT_TSDEMUX_TAP, which sends TS to the demux0 device. With this
patch and a dvb-usb-dib0700 (and UK Freeview from Sandy Heath), I can
successfully capture an audio/video PID pair into a TS file that mplayer
can play back.
Signed-off-by: Peter Hartley <pdh@utter.chaos.org.uk>
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only attach cameras to the host interface for probing, then detach until
open. This allows platforms with several cameras on an interface,
physically supporting only one camera, to handle multiple cameras and
activate them selectively after initial probing. The first attach during
probe is needed to activate the host interface to be able to physically
communicate with cameras.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videobuf-dma-sg does not need to depend on PCI. Switch it to using generic
DMA API, convert all affected drivers, relax Kconfig restriction, improve
compile-time type checking, fix some Coding Style violations while at it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Continue to support the V4L2_CID_PRIVATE_BASE + 1 control in the ABI
- Report the same control as V4L2_CID_SHARPNESS
- Report the private control disabled via QUERYCTRL
Signed-off-by: Brandon Philips <bphilips@suse.de>
Acked-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds two new fourcc codes (as per info at fourcc.org)
for 16bpp mono and 16bpp Bayer formats.
Signed-off-by: Steven Whitehouse <steve@chygwyn.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver provides an interface between platform-specific camera
busses and camera devices. It should be used if the camera is connected
not over a "proper" bus like PCI or USB, but over a special bus, like,
for example, the Quick Capture interface on PXA270 SoCs. Later it should
also be used for i.MX31 SoCs from Freescale. It can handle multiple
cameras and / or multiple busses, which can be used, e.g., in
stereo-vision applications.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add V4L2_IDENT chip IDs for mt9m001 and mt9v022 cameras, will be used by
future patches, primarily to implement the g_chip_ident ioctl.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add all of the recently proposed camera class controls. These controls
should appear in the next version of the v4l2spec.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These changes should appear in the next update of the v4l2spec.
HCENTER and VCENTER are unused in the tree so I added a _DEPRECATED
postfix so applications can remove their use.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (85 commits)
Blackfin char driver for Blackfin on-chip OTP memory (v3)
Blackfin Serial Driver: fix bug - use mod_timer to replace only add_timer.
Blackfin Serial Driver: the uart break anomaly has been given its own number, so switch to it
Blackfin Serial Driver: use BFIN_UART_NR_PORTS to help SIR driver in uart port.
Blackfin Serial Driver: Fix bug - kernel hangs when accessing uart 0 on bf537 when booting u-boot and linux on uart 1
Blackfin Serial Driver: punt unused lsr variable
Blackfin Serial Driver: Enable IR function when user application (irattach /dev/ttyBFx -s) call TIOCSETD ioctl with line discipline N_IRDA
[Blackfin] arch: add include/boot .gitignore files
[Blackfin] arch: Functional power management support: Add support for cpu frequency scaling
[Blackfin] arch: Functional power management support: Remove broken cpu frequency scaling drivers
[Blackfin] arch: Equalize include files: Add PLL_DIV Masks
[Blackfin] arch: Add a warning about the value of CLKIN.
[Blackfin] arch: take DDR DEVWD into consideration as well for BF548
[Blackfin] arch: Remove the circular buffering mechanism for exceptions
[Blackfin] arch: lose unnecessary dependency on CONFIG_BFIN_ICACHE for MPU
[Blackfin] arch: fix bug - before assign new channel to the map register, need clear the bits first.
[Blackfin] arch: add Blackfin on-chip SIR IrDA driver support
[Blackfin] arch: BF54x memsizes are in mbits, not mbytes
[Blackfin] arch: try to remove condition that causes double fault, by checking current before it gets dereferenced
[Blackfin] arch: Update anomaly list.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (22 commits)
tun: Multicast handling in tun_chr_ioctl() needs proper locking.
[NET]: Fix heavy stack usage in seq_file output routines.
[AF_UNIX] Initialise UNIX sockets before general device initcalls
[RTNETLINK]: Fix bogus ASSERT_RTNL warning
iwlwifi: Fix built-in compilation of iwlcore (part 2)
tun: Fix minor race in TUNSETLINK ioctl handling.
ppp_generic: use stats from net_device structure
iwlwifi: Don't unlock priv->mutex if it isn't locked
wireless: rndis_wlan: modparam_workaround_interval is never below 0.
prism54: prism54_get_encode() test below 0 on unsigned index
mac80211: update mesh EID values
b43: Workaround DMA quirks
mac80211: fix use before check of Qdisc length
net/mac80211/rx.c: fix off-by-one
mac80211: Fix race between ieee80211_rx_bss_put and lookup routines.
ath5k: Fix radio identification on AR5424/2424
ssb: Fix all-ones boardflags
b43: Add more btcoexist workarounds
b43: Fix HostFlags data types
b43: Workaround invalid bluetooth settings
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: (23 commits)
sparc: sunzilog uart order
[SPARC64]: Detect trap frames in stack backtraces.
[SPARC64]: %l6 trap return handling no longer necessary.
[SPARC64]: Use trap type stored in pt_regs to handle syscall restart.
[SPARC64]: Store magic cookie and trap type in pt_regs.
[SPARC64]: PROM debug console can be CON_ANYTIME.
sparc64: cleanup after SunOS/Solaris binary emulation removal
sparc: cleanup after SunOS binary emulation removal
[SPARC64]: Add NUMA support.
[SPARC64]: Allocate TSB node-local.
[SPARC64]: NUMA device infrastructure.
[SPARC64]: Kill pci_iommu_table_init() declaration.
[SPARC64]: Once we have the boot cmdline, call parse_early_param()
[SPARC64]: Remove unused asm-sparc64/numnodes.h
[SPARC64]: Decrease SECTION_SIZE_BITS to 30.
[SPARC64]: Initialize MDESC earlier and use lmb_alloc()
[SPARC64]: Use lmb_alloc() for PROM device tree.
[SPARC64]: Call real_setup_per_cpu_areas() earlier and use lmb_alloc().
[SPARC64]: Fully use LMB information in bootmem_init().
[SPARC64]: Start using LMB information in bootmem_init().
...
This splits cell io-workaround code into spider-pci dependent code and
a generic part, and also moves io-workarounds initialization into
cell_setup_phb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the required functionality to fill in all pacas at runtime.
With NR_CPUS=1024
text data bss dec hex filename
137 1704032 0 1704169 1a00e9 arch/powerpc/kernel/paca.o :Before
121 1179744 524288 1704153 1a00d9 arch/powerpc/kernel/paca.o :After
Also remove unneeded #includes from arch/powerpc/kernel/paca.c
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The fixmap code from x86 allows us to have compile time virtual addresses
that we change the physical addresses of at run time.
This is useful for applications like kmap_atomic, PCI config that is done
via direct memory map, kexec/kdump.
We got ride of CONFIG_HIGHMEM_START as we can now determine a more optimal
location for PKMAP_BASE based on where the fixmap addresses start and
working back from there.
Additionally, the kmap code in asm-powerpc/highmem.h always had debug
enabled. Moved to using CONFIG_DEBUG_HIGHMEM to determine if we should
have the extra debug checking.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added support to allow an 85xx kernel to be run from a non-zero physical
address (useful for cooperative asymmetric multiprocessing situations and
kdump). The support can be configured at compile time by setting
CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as
desired.
Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this
config option causes the kernel to determine at runtime the physical
addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If
CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning.
However, CONFIG_PHYSICAL_START will always be used to set the LOAD program
header physical address field in the resulting ELF image.
Currently we are limited to running at a physical address that is a
multiple of 256M. This is due to how we map TLBs to cover
lowmem. This should be fixed to allow 64M or maybe even 16M alignment
in the future. It is considered an error to try and run a kernel at a
non-aligned physical address.
All the magic for this support is accomplished by proper initialization
of the kernel memory subsystem and use of ARCH_PFN_OFFSET.
The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings.
ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET.
/dev/mem continues to allow access to any physical address in the system
regardless of how CONFIG_PHYSICAL_START is set.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit d04ceb3fc2 moved phys_addr_t
definitions to include/asm-powerpc/types.h. However, arch/ppc 440
builds had a duplicate definition in include/asm-ppc/mmu.h that caused
the build to fail.
This removes the duplicate definition in arch/ppc.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc kernel stacks need to be naturally aligned, as they
contain the thread info at the bottom, which is obtained by
clearing the low bits of the stack pointer.
However, when using 64K pages, the stack is smaller than a page,
so we use kmalloc to allocate it, but that doesn't provide the
alignment guarantee we need.
It appeared to work so far... until one enables SLUB debugging
which then returns unaligned pointers. Ooops...
This fixes it by using a slab cache with enforced alignment. It
relies on my previous patch that adds a thread_info_cache_init()
callback.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some architectures need to maintain a kmem cache for thread info
structures. The next commit adds that to powerpc to fix an alignment
problem.
There is no good arch callback to use to initialize that cache
that I can find, so this adds a new one in the form of a weak
function whose default is empty.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that we indicate the "restart system call" in the
trap type field of pt_regs->magic, we don't need to
set the %l6 boolean in all of the trap return paths.
And we therefore don't need to pass it to do_notify_resume().
Signed-off-by: David S. Miller <davem@davemloft.net>
snd_minor_info_oss_* is an function returning int _or_ comment,
depending on config parameters. That is truly evil, fix it.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two sentences seem to be spliced into one in comment, fix that and fix
english. Also fix codingstyle.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* removing the hack with NON_AKM ak4xxx type
* support for card-specific flags in ak4114_stats
* definition of the flags for corresponding cards
Signed-off-by: Pavel Hofman <dustin@seznam.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added definition for byte 4 of SPDIF channel status, according to
second edition of IEC 60958-3 (consumer) spec.
Signed-off-by: Pawel MOLL <pawel.moll@st.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the codes for virtual master controls to sound core part so that
not only hda-intel drivers can use it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the support of 8 channel sound for codecs that are known to work.
So far, only ALC850 is marked as a 8ch-support codec.
This fix is a modified version of the patch on ALSA BTS#2097 by
Martin Ellis:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=2097
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This sets us up for several simplifications and facilities:
1) The magic cookie lets us identify trap frames more
accurately in stack backtraces.
2) The trap type lets us simplify all of the "are we in
a syscall" state management and checks.
3) We can now see if a task off the cpu is sleeping in
a system call or not. In fact, we can see what
trap it is sleeping in whatever the type. The utrace
guys will use this.
Based upon some discussions with Roland McGrath.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is only code to parse NUMA attributes on
sun4v/niagara systems, but later on we will add such parsing
for older systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
ASSERT_RTNL uses mutex_trylock to test whether the rtnl_mutex is
held. This bogus warnings when running in atomic context, which
f.e. happens when adding secondary unicast addresses through
macvlan or vlan or when synchronizing multicast addresses from
wireless devices.
Mid-term we might want to consider moving all address updates
to process context since the locking seems overly complicated,
for now just fix the bogus warning by changing ASSERT_RTNL to
use mutex_is_locked().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates mesh EID values, some of which where conflicting with
already-approved 11h EIDs (pointed out by Tomas Winkler). I wanted to use the
values suggested in the last available 802.11 draft (2.0) but it assigns 50 to
MESH_CONFIG, the same value than EXT_SUPP_RATES. Using the values proposed in
the draft incremented by one.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up: Update the RPC server's TCP record marker decoder to match the
constructs used by the RPC client's TCP socket transport.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
The raw field's size can vary so we use a zero sized array since
gcc will not allow a variable sized array inside a union. This
has been tested with ext3 and gfs2 and relates to the bug
report: http://lkml.org/lkml/2007/10/24/374 and discussion
thread: http://lkml.org/lkml/2008/4/7/65
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Now that the nfs4 callback thread uses the kthread API, there are no
more users of svc_create_thread(). Remove it.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Consistently use unsigned (u32 vs. s32) for seqnum.
In get_mic function, send the local copy of seq_send,
rather than the context version.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
cleanup: When adding new encryption types, the checksum length
can be different for each enctype. Face the fact that the
current code only supports DES which has a checksum length of 8.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Add extern to nfsd/nfsd.h
fs/nfsd/nfssvc.c:146:5: warning: symbol 'nfsd_nrthreads' was not declared. Should it be static?
fs/nfsd/nfssvc.c:261:5: warning: symbol 'nfsd_nrpools' was not declared. Should it be static?
fs/nfsd/nfssvc.c:269:5: warning: symbol 'nfsd_get_nrthreads' was not declared. Should it be static?
fs/nfsd/nfssvc.c:281:5: warning: symbol 'nfsd_set_nrthreads' was not declared. Should it be static?
fs/nfsd/export.c:1534:23: warning: symbol 'nfs_exports_op' was not declared. Should it be static?
Add include of auth.h
fs/nfsd/auth.c:27:5: warning: symbol 'nfsd_setuser' was not declared. Should it be static?
Make static, move forward declaration closer to where it's needed.
fs/nfsd/nfs4state.c:1877:1: warning: symbol 'laundromat_main' was not declared. Should it be static?
Make static, forward declaration was already marked static.
fs/nfsd/nfs4idmap.c:206:1: warning: symbol 'idtoname_parse' was not declared. Should it be static?
fs/nfsd/vfs.c:1156:1: warning: symbol 'nfsd_create_setattr' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
This field is set once and never used; probably some artifact of an
earlier implementation idea.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Thanks to Robert Day for pointing out that these two defines are unused.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Cc: Trond Myklebust <trond@netapp.com>Trond Myklebust <trond@netapp.com>
Cc: Neil Brown <neilb@suse.de>
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
This adds IPv6 support to the interfaces that are used to express nfsd
exports. All addressed are stored internally as IPv6; backwards
compatibility is maintained using mapped addresses.
Thanks to Bruce Fields, Brian Haley, Neil Brown and Hideaki Joshifuji
for comments
Signed-off-by: Aurelien Charbon <aurelien.charbon@bull.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Brian Haley <brian.haley@hp.com>
Cc: YOSHIFUJI Hideaki / 吉藤英明 <yoshfuji@linux-ipv6.org>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[patch 7/7] vfs: mountinfo: show dominating group id
[patch 6/7] vfs: mountinfo: add /proc/<pid>/mountinfo
[patch 5/7] vfs: mountinfo: allow using process root
[patch 4/7] vfs: mountinfo: add mount peer group ID
[patch 3/7] vfs: mountinfo: add mount ID
[patch 2/7] vfs: mountinfo: add seq_file_root()
[patch 1/7] vfs: mountinfo: add dentry_path()
[PATCH] remove unused label in xattr.c (noise from ro-bind)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
iwlwifi: Fix built-in compilation of iwlcore
net: Unexport move_addr_to_{kernel,user}
rt2x00: Select LEDS_CLASS.
iwlwifi: Select LEDS_CLASS.
leds: Do not guard NEW_LEDS with HAS_IOMEM
[IPSEC]: Fix catch-22 with algorithm IDs above 31
time: Export set_normalized_timespec.
tcp: Make use of before macro in tcp_input.c
hamradio: Remove unneeded and deprecated cli()/sti() calls in dmascc.c
[NETNS]: Remove empty ->init callback.
[DCCP]: Convert do_gettimeofday() to getnstimeofday().
[NETNS]: Don't initialize err variable twice.
[NETNS]: The ip6_fib_timer can work with garbage on net namespace stop.
[IPV4]: Convert do_gettimeofday() to getnstimeofday().
[IPV4]: Make icmp_sk_init() static.
[IPV6]: Make struct ip6_prohibit_entry_template static.
tcp: Trivial fix to correct function name in a comment in net/ipv4/tcp.c
[NET]: Expose netdevice dev_id through sysfs
skbuff: fix missing kernel-doc notation
[ROSE]: Fix soft lockup wrt. rose_node_list_lock
In addition to mlx4_ib, there will be ethernet and FC consumers of
mlx4_core, so move the code for managing kernel doorbells into the
core module to avoid having to duplicate this multiple times.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
[mszeredi@suse.cz] rewrite and split big patch into managable chunks
/proc/mounts in its current form lacks important information:
- propagation state
- root of mount for bind mounts
- the st_dev value used within the filesystem
- identifier for each mount and it's parent
It also suffers from the following problems:
- not easily extendable
- ambiguity of mountpoints within a chrooted environment
- doesn't distinguish between filesystem dependent and independent options
- doesn't distinguish between per mount and per super block options
This patch introduces /proc/<pid>/mountinfo which attempts to address
all these deficiencies.
Code shared between /proc/<pid>/mounts and /proc/<pid>/mountinfo is
extracted into separate functions.
Thanks to Al Viro for the help in getting the design right.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Allow /proc/<pid>/mountinfo to use the root of <pid> to calculate
mountpoints.
- move definition of 'struct proc_mounts' to <linux/mnt_namespace.h>
- add the process's namespace and root to this structure
- pass a pointer to 'struct proc_mounts' into seq_operations
In addition the following cleanups are made:
- use a common open function for /proc/<pid>/{mounts,mountstat}
- surround namespace.c part of these proc files with #ifdef CONFIG_PROC_FS
- make the seq_operations structures const
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a unique ID to each peer group using the IDR infrastructure. The
identifiers are reused after the peer group dissolves.
The IDR structures are protected by holding namepspace_sem for write
while allocating or deallocating IDs.
IDs are allocated when a previously unshared vfsmount becomes the
first member of a peer group. When a new member is added to an
existing group, the ID is copied from one of the old members.
IDs are freed when the last member of a peer group is unshared.
Setting the MNT_SHARED flag on members of a subtree is done as a
separate step, after all the IDs have been allocated. This way an
allocation failure can be cleaned up easilty, without affecting the
propagation state.
Based on design sketch by Al Viro.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a unique ID to each vfsmount using the IDR infrastructure. The
identifiers are reused after the vfsmount is freed.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a new function:
seq_file_root()
This is similar to seq_path(), but calculates the path relative to the
given root, instead of current->fs->root. If the path was unreachable
from root, then modify the root parameter to reflect this.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[mszeredi@suse.cz] split big patch into managable chunks
Add the following functions:
dentry_path()
seq_dentry()
These are similar to d_path() and seq_path(). But instead of
calculating the path within a mount namespace, they calculate the path
from the root of the filesystem to a given dentry, ignoring mounts
completely.
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] get rid of __exit_files(), __exit_fs() and __put_fs_struct()
[PATCH] proc_readfd_common() race fix
[PATCH] double-free of inode on alloc_file() failure exit in create_write_pipe()
[PATCH] teach seq_file to discard entries
[PATCH] umount_tree() will unhash everything itself
[PATCH] get rid of more nameidata passing in namespace.c
[PATCH] switch a bunch of LSM hooks from nameidata to path
[PATCH] lock exclusively in collect_mounts() and drop_collected_mounts()
[PATCH] move a bunch of declarations to fs/internal.h
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] run drivers/misc/sgi-xp through scripts/checkpatch.pl
[IA64] run rest drivers/misc/sgi-xp through scripts/Lindent
[IA64] run some drivers/misc/sgi-xp through scripts/Lindent
[IA64] move XP and XPC to drivers/misc/sgi-xp
[IA64] minor irq handler cleanups
[IA64] simplify notify hooks in mca.c
[IA64] do notify DIE_MCA_MONARCH_PROCESS for each monarchs
[IA64] disable interrupts on exit of ia64_trace_syscall
Move XPC and XPNET from arch/ia64/sn/kernel to drivers/misc/sgi-xp.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix platform driver hotplug/coldplug
i2c: New driver for the SuperH Mobile I2C bus controller
i2c/scx200_acb: Don't use 0 as NULL pointer
i2c-bfin-twi: Fix mismatch in add timer and delete timer
i2c-bfin-twi: Just let i2c-bfin-twi driver depends on BLACKFIN
i2c-bfin-twi: Use simpler comment headers and strip out information that is maintained in the scm's log
i2c-bfin-twi: Cleanup driver descriptions, versions and some module useful information
i2c-bfin-twi: Add missing pin mux operation
i2c-bfin-twi: Add platform_resource interface to support multi-port TWI controllers
i2c-bfin-twi: Add repeat start feature to avoid break of a bundle of i2c master xfer operation
i2c: Remove trailing whitespaces in busses/Kconfig
i2c: Replace remaining __FUNCTION__ occurrences
i2c: Renesas SH7760 I2C master driver
i2c-dev: Split i2cdev_ioctl
i2c-ibm_iic: Support building as an of_platform driver
i2c-ibm_iic: Change the log levels
i2c: Add platform driver on top of the new pca-algorithm
i2c-algo-pca: Extend for future drivers
i2c-algo-pca: Remove trailing whitespaces and unnecessary UTF
i2c: Remove the algorithm drivers from the config menu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: linux/{dlm,dlm_device}.h: cleanup for userspace
dlm: common max length definitions
dlm: move plock code from gfs2
dlm: recover nodes that are removed and re-added
dlm: save master info after failed no-queue request
dlm: make dlm_print_rsb() static
dlm: match signedness between dlm_config_info and cluster_set
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Suppress hidinput for Samsung IR control
HID: remove 60x GTCO devices from blacklist
HID: export headers properly
HID: WiseGroup 866 Dual Joypad needs output reports quirk
HID: ThrustMaster FF driver is no longer experimental
HID: Logitech diNovo Mini pad support
HID: fix race between open() and disconnect() in usbhid
HID: make hid_input_field and usbhid_modify_dquirk static
HID: pass numbered reports properly to hidraw
HID: fix misplaced rdesc quirk
HID: force feedback driver for Logitech Rumblepad 2
HID: move wait from hid to usbhid
HID: make function from dbg_hid
HID: fix sparse warnings
HID: only dump report traffic with debug level 2
HID: patch to add NOGET for DMI/Acomdata
HID: Sunplus Wireless Desktop needs report descriptor fixup
HID: quirk for MS Wireless Desktop Receiver (model 1028)
HID: fixup fullspeed interval on highspeed Afatech DVB-T IR kbd
HID: fix build failure in hiddev_ioctl with gcc 3.2
Add support to disable ECC checking for a given chip
when passed by the board via the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for the ECC layout to be passed via the
platform data specified by the board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If a block's ecc field is all 0xff, then ignore the ECC
correction. This is for systems where some of the blocks,
such as the initial cramfs are written without ECC and
need to be loaded on start.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6: (41 commits)
udf: use crc_itu_t from lib instead of udf_crc
udf: Fix compilation warnings when UDF debug is on
udf: Fix bug in VAT mapping code
udf: Add read-only support for 2.50 UDF media
udf: Fix handling of multisession media
udf: Mount filesystem read-only if it has pseudooverwrite partition
udf: Handle VAT packed inside inode properly
udf: Allow loading of VAT inode
udf: Fix detection of VAT version
udf: Silence warning about accesses beyond end of device
udf: Improve anchor block detection
udf: Cleanup anchor block detection.
udf: Move processing of virtual partitions
udf: Move filling of partition descriptor info into a separate function
udf: Improve error recovery on mount
udf: Cleanup volume descriptor sequence processing
udf: fix anchor point detection
udf: Remove declarations of arrays of size UDF_NAME_LEN (256 bytes)
udf: Remove checking of existence of filename in udf_add_entry()
udf: Mark udf_process_sequence() as noinline
...
Driver for I2C interfaces in master mode on SH7760.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The separation between algorithm and adapter was unsharp at places. This was
partly hidden by the fact, that the ISA-driver allowed just one instance and
had all private data in static variables. This patch makes neccessary
preparations to add a platform driver on top of the algorithm, while still
supporting ISA. Note: Due to lack of hardware, the ISA-driver could not be
tested except that it builds.
Concerning the core struct i2c_algo_pca_data:
- A private data field was added, all hardware dependant data may go here.
Similar to other algorithms, now a pointer to this data is passed to the
adapter's functions. In order to make as less changes as possible to the
ISA-driver, it leaves the private data empty and still only uses its static
variables.
- A "reset_chip" function pointer was added; such a functionality must come
from the adapter, not the algorithm.
- use a variable "i2c_clock" instead of a function pointer "get_clock",
allowing for write access to a default in case a wrong value was supplied.
In the algorithm-file:
- move "i2c-pca-algo.h" into "linux/i2c-algo-pca.h"
- now using per_instance timeout values (i2c_adap->timeout)
- error messages specify the device, not only the driver name
- restructure initialization to easily support "i2c_add_numbered_adapter"
- drop "retries" and "own" (i2c address) as they were unused
(The state-machine for I2C-communication was not touched.)
In the ISA-driver:
- adapt to new algorithm
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds release callback support, which is called when a bsg
device goes away. bsg_register_queue() takes a pointer to a callback
function. This feature is useful for stuff like sas_host that can't
use the release callback in struct device.
If a caller doesn't need bsg's release callback, it can call
bsg_register_queue() with NULL pointer (e.g. scsi devices can use
release callback in struct device so they don't need bsg's callback).
With this patch, bsg uses kref for refcounts on bsg devices instead of
get/put_device in fops->open/release. bsg calls put_device and the
caller's release callback (if it was registered) in kref_put's
release.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current target allocation code registeres each possible target
with sysfs; it will be deleted again if no useable LUN on this target
was found. This results in a string of 'target add/target remove' uevents.
Based on a patch by Hannes Reinecke <hare@suse.de> this patch reworks
the target allocation code so that only uevents for existing targets
are sent. The sysfs registration is split off from the existing
scsi_target_alloc() into a in a new scsi_add_target() function, which
should be called whenever an existing target is found. Only then a
uevent is sent, so we'll be generating events for existing targets
only.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We have a problem in scsi_transport_spi in that we need to customise
not only the visibility of the attributes, but also their mode. Fix
this by making the is_visible() callback return a mode, with 0
indicating is not visible.
Also add a sysfs_update_group() API to allow us to change either the
visibility or mode of the files at any time on the fly.
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This enhances plat-ram to take a map_probes argument in
the platform_data structure which allow plat-ram to support
any direct-mapped device that MTD supports (jedec, cfi, amd ..)
A few items are also fixed:
- Don't panic if probes is 0
- Actually use the partition list that is passed in
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is preliminary since:
1. It supports only _one_ chip select at the moment. As there is no
existing platforms available using two chip selects of the NAND
controller, it shall really not include code for supporting the
2nd chip select for now, as such code cannot be verified.
2. It resorts to the default and simpliest memory based badblock
table
3. Only limited types of nand flash are currently supported. Most
PXA3xx processors come with on-chip NAND flash dies, so there
isn't much flexibility for other types of NAND.
4. The NAND controller should be configured to detect the device's
ID, thus making it difficult to use nand_scan_ident() to assist
the detection process (though it's not impossible)
TODO: fix all the above limitations of cuz :-)
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
There are many notify_die() and almost all take same style with
ia64_mca_spin(). This patch defines macros and replace them all,
to reduce lines and to improve readability.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch adds a proper prototype for onenand_bbt_read_oob() in
include/linux/mtd/onenand.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds proper prototypes for nftl_{read,write}_oob() in
include/linux/mtd/nftl.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds proper prototypes for inftl_{read,write}_oob() in
include/linux/mtd/inftl.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I have people whining about using these headers in userspace, and they have
__KERNEL__ markings which implies they're supposed to be exported. I also
added the required linux/types.h include to hidraw.h since it uses the __u##
kernel types.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Jiri Kosina <jikos@jikos.cz>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a window:
task A task B
spin_lock_irq(&usbhid->inlock); /* Sync with error handler */
usb_set_intfdata(intf, NULL);
spin_unlock_irq(&usbhid->inlock);
usb_kill_urb(usbhid->urbin);
usb_kill_urb(usbhid->urbout);
usb_kill_urb(usbhid->urbctrl);
del_timer_sync(&usbhid->io_retry);
cancel_work_sync(&usbhid->reset_work);
if (!hid->open++) {
res = usb_autopm_get_interface(usbhid->intf);
if (res < 0) {
hid->open--;
return -EIO;
}
}
if (hid_start_in(hid))
if (hid->claimed & HID_CLAIMED_INPUT)
hidinput_disconnect(hid);
in which an open() to an already disconnected device will submit an URB
to an undead device. In case disconnect() was called by an ioctl, this'll
oops. Fix by introducing a new flag and checking it in hid_start_in().
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch makes the following needlessly global functions static:
- hid-core.c:hid_input_field()
- usbhid/hid-quirks.c:usbhid_modify_dquirk()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add force feedback support for Logitech Rumblepad 2.
Tested-By: Edgar Simo <bobbens@gmail.com>
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To check paramters even if debug is disabled, convert dbg_hid
to inline function with __attribute__(format) checking.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device has reports lower logical maximum compared to the real
usages for Zoom+ and Zoom- it emits.
This patch bumps the values in the report descriptor up, and also
adjusts HID_MAX_USAGE accordingly.
Reported-by: Khelben Blackstaff <eye.of.the.8eholder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft's wireless desktop receiver (Model 1028) has a bug in the report
descriptor -- namely, in four seperate places it uses USAGE_MIN and _MAX when
it quite obviously doesn't intend to.
In other words, it reports that it has pretty much _everything_ in 'consumer'
and 'generic desktop'. And then the X evdev driver believes I have a mouse
with 36 absolute axes and a huge pile of keys and buttons, when I in fact,
should have zero. 255/256 in three of the cases, and 0-1024 in another.
This patch fixes the report descriptor of this device before it enters the HID
parser.
Signed-off-by: Jim Duchek <jim.duchek@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many vendors highspeed devices give erroneously fullspeed interval value in
endpoint descriptor for interrupt endpoints. This quirk fixes up that by
recalculating the right value for highspeed device.
At the time of hid configuration this quirk calculates which highspeed interval
value gives same interval delay as, or next smaller then, what it would be if
the original value would be interpreted as fullspeed value. In subsequent urbs
that new value is used instead.
Forming the 'hid->name' in usb_hid_config() was moved up to accommodate more
descriptive printk reporting the fixup.
In this patch the quirk is set for one such device: Afatech DVB-T 2 infrared
HID-keyboard. It reports value 16 which means 4,069s in highspeed while
obviously 16ms was intended. In this case quirk calculates new value to be 8
which gives when interpreted as highspeed value 16ms as wanted. The behavior of
the device was verified to be what expected both before and after the patch.
Signed-off-by: Pekka Sarnila <sarnila@adit.fi>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As it stands it's impossible to use any authentication algorithms
with an ID above 31 portably. It just happens to work on x86 but
fails miserably on ppc64.
The reason is that we're using a bit mask to check the algorithm
ID but the mask is only 32 bits wide.
After looking at how this is used in the field, I have concluded
that in the long term we should phase out state matching by IDs
because this is made superfluous by the reqid feature. For current
applications, the best solution IMHO is to allow all algorithms when
the bit masks are all ~0.
The following patch does exactly that.
This bug was identified by IBM when testing on the ppc64 platform
using the NULL authentication algorithm which has an ID of 251.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (26 commits)
mmc: sdio_ops.c should #include "sdio_ops.h"
mmc: proper prototypes for mmc_attach_*()
mmc: make __mmc_release_bus() static
sdhci: improve no card, no reset quirk
MMC: OMAP: Do not busy wait for end of command for ever
MMC: OMAP: Start new commands from work queue instead of irq
MMC: OMAP: Lazy clock shutdown
MMC: OMAP: Move failing command abortion to workqueue
MMC: OMAP: Use tasklet instead of workqueue for cover switch notification
MMC: OMAP: Check the get_cover_state function pointer if not set
MMC: OMAP: Using setup_timer instead of init_timer
MMC: OMAP: Abort stuck commands
MMC: OMAP: General cleanup for MMC multislot support
MMC: OMAP: Power functions modified to MMC multislot support
MMC: OMAP: Fix timeout calculation for MMC multislot support
MMC: OMAP: New release dma and abort xfer functions
MMC: OMAP: Add back cover switch support
MMC: OMAP: Introduce new multislot structure and change driver to use it
MMC: OMAP: Remove cover switch handling to allow adding multislot support
MMC: OMAP: Fix the BYTEBLOCK capability removal
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/juhl/trivial: (24 commits)
DOC: A couple corrections and clarifications in USB doc.
Generate a slightly more informative error msg for bad HZ
fix typo "is" -> "if" in Makefile
ext*: spelling fix prefered -> preferred
DOCUMENTATION: Use newer DEFINE_SPINLOCK macro in docs.
KEYS: Fix the comment to match the file name in rxrpc-type.h.
RAID: remove trailing space from printk line
DMA engine: typo fixes
Remove unused MAX_NODES_SHIFT
MAINTAINERS: Clarify access to OCFS2 development mailing list.
V4L: Storage class should be before const qualifier (sn9c102)
V4L: Storage class should be before const qualifier
sonypi: Storage class should be before const qualifier
intel_menlow: Storage class should be before const qualifier
DVB: Storage class should be before const qualifier
arm: Storage class should be before const qualifier
ALSA: Storage class should be before const qualifier
acpi: Storage class should be before const qualifier
firmware_sample_driver.c: fix coding style
MAINTAINERS: Add ati_remote2 driver
...
Fixed up trivial conflicts in firmware_sample_driver.c
* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block:
block: fix blk_register_queue() return value
block: fix memory hotplug and bouncing in block layer
block: replace remaining __FUNCTION__ occurrences
Kconfig: clean up block/Kconfig help descriptions
cciss: fix warning oops on rmmod of driver
cciss: Fix race between disk-adding code and interrupt handler
block: move the padding adjustment to blk_rq_map_sg
block: add bio_copy_user_iov support to blk_rq_map_user_iov
block: convert bio_copy_user to bio_copy_user_iov
loop: manage partitions in disk image
cdrom: use kmalloced buffers instead of buffers on stack
cdrom: make unregister_cdrom() return void
cdrom: use list_head for cdrom_device_info list
cdrom: protect cdrom_device_info list by mutex
cdrom: cleanup hardcoded error-code
cdrom: remove ifdef CONFIG_SYSCTL
HARD_RESET_NOW() was unused.
And one of the few remaining cli() users.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[HWRNG] omap: Minor updates
[CRYPTO] kconfig: Ordering cleanup
[CRYPTO] all: Clean up init()/fini()
[CRYPTO] padlock-aes: Use generic setkey function
[CRYPTO] aes: Export generic setkey
[CRYPTO] api: Make the crypto subsystem fully modular
[CRYPTO] cts: Add CTS mode required for Kerberos AES support
[CRYPTO] lrw: Replace all adds to big endians variables with be*_add_cpu
[CRYPTO] tcrypt: Change the XTEA test vectors
[CRYPTO] tcrypt: Shrink the tcrypt module
[CRYPTO] tcrypt: Change the usage of the test vectors
[CRYPTO] api: Constify function pointer tables
[CRYPTO] aes-x86-32: Remove unused return code
[CRYPTO] tcrypt: Shrink speed templates
[CRYPTO] tcrypt: Group common speed templates
[CRYPTO] sha512: Rename sha512 to sha512_generic
[CRYPTO] sha384: Hardware acceleration for s390
[CRYPTO] sha512: Hardware acceleration for s390
[CRYPTO] s390: Generic sha_update and sha_final
[CRYPTO] api: Switch to proc_create()
* 'irq-cleanups-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
[ISDN] minor irq handler cleanups
drivers/char: minor irq handler cleanups
[PPC] minor irq handler cleanups
[BLACKFIN] minor irq handler cleanups
[SPARC] minor irq handler cleanups
ARM minor irq handler cleanup: avoid passing unused info to irq
Generate a slightly more informative error msg for bad HZ
in include/linux/jiffies.h
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Add kernel-doc notation for ndisc_nodetype:
Warning(linux-2.6.25-git2//include/linux/skbuff.h:340): No description found for parameter 'ndisc_nodetype'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
SCSI: convert struct class_device to struct device
DRM: remove unused dev_class
IB: rename "dev" to "srp_dev" in srp_host structure
IB: convert struct class_device to struct device
memstick: convert struct class_device to struct device
driver core: replace remaining __FUNCTION__ occurrences
sysfs: refill attribute buffer when reading from offset 0
PM: Remove destroy_suspended_device()
Firmware: add iSCSI iBFT Support
PM: Remove legacy PM (fix)
Kobject: Replace list_for_each() with list_for_each_entry().
SYSFS: Explicitly include required header file slab.h.
Driver core: make device_is_registered() work for class devices
PM: Convert wakeup flag accessors to inline functions
PM: Make wakeup flags available whenever CONFIG_PM is set
PM: Fix misuse of wakeup flag accessors in serial core
Driver core: Call device_pm_add() after bus_add_device() in device_add()
PM: Handle device registrations during suspend/resume
block: send disk "change" event for rescan_partitions()
sysdev: detect multiple driver registrations
...
Fixed trivial conflict in include/linux/memory.h due to semaphore header
file change (made irrelevant by the change to mutex).
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
hrtimer: optimize the softirq time optimization
hrtimer: reduce calls to hrtimer_get_softirq_time()
clockevents: fix typo in tick-broadcast.c
jiffies: add time_is_after_jiffies and others which compare with jiffies
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel: (62 commits)
sched: build fix
sched: better rt-group documentation
sched: features fix
sched: /debug/sched_features
sched: add SCHED_FEAT_DEADLINE
sched: debug: show a weight tree
sched: fair: weight calculations
sched: fair-group: de-couple load-balancing from the rb-trees
sched: fair-group scheduling vs latency
sched: rt-group: optimize dequeue_rt_stack
sched: debug: add some debug code to handle the full hierarchy
sched: fair-group: SMP-nice for group scheduling
sched, cpuset: customize sched domains, core
sched, cpuset: customize sched domains, docs
sched: prepatory code movement
sched: rt: multi level group constraints
sched: task_group hierarchy
sched: fix the task_group hierarchy for UID grouping
sched: allow the group scheduler to have multiple levels
sched: mix tasks and groups
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86: (77 commits)
x86: UV startup of slave cpus
x86: integrate pci-dma.c
x86: don't do dma if mask is NULL.
x86: return conditional to mmu
x86: remove kludge from x86_64
x86: unify gfp masks
x86: retry allocation if failed
x86: don't try to allocate from DMA zone at first
x86: use a fallback dev for i386
x86: use numa allocation function in i386
x86: remove virt_to_bus in pci-dma_64.c
x86: adjust dma_free_coherent for i386
x86: move bad_dma_address
x86: isolate coherent mapping functions
x86: move dma_coherent functions to pci-dma.c
x86: merge iommu initialization parameters
x86: merge dma_supported
x86: move pci fixup to pci-dma.c
x86: move x86_64-specific to common code.
x86: move initialization functions to pci-dma.c
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (27 commits)
sh: Fix up L2 cache probe.
sh: Fix up SH-4A part probe.
sh: Add support for SH7723 CPU subtype.
sh: Fix up SH7763 build.
sh: Add migor_ts support to MigoR
sh: Add rs5c732b RTC support to MigoR
sh: Add I2C support to MigoR
sh: Add I2C platform data to sh7722
sh: MigoR NAND flash support using gen_flash
sh: MigoR NOR flash support using physmap-flash
sh: Fix up mach-types formatting from merge damage.
sh: r7780rp: Hook up the I2C and SMBus platform devices.
sh: Use phyical addresses for MigoR smc91x resources
sh: Use physical addresses for sh7722 USBF resources
sh: Add MigoR header file
Fix sh_keysc double free
sh: Fix up __access_ok() check for nommu.
sh: Allow optimized clear/copy page routines to be used on SH-2.
sh: Hook up the rest of the SH7770 serial ports.
sh: Add support for Solution Engine SH7721 board
...
MAX_NODES_SHIFT is not referenced anywhere in the tree, so dump it.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
linux/dlm_device.h uses types from dlm.h and types.h, so pull them in. The
dlm.h header should use __u## rather than uint##_t types and thus pull in
linux/types.h for it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Teigland <teigland@redhat.com>
Add central definitions for max lockspace name length and max resource
name length. The lack of central definitions has resulted in scattered
private definitions which we can now clean up, including an unused one
in dlm_device.h.
Signed-off-by: David Teigland <teigland@redhat.com>
Move the code that handles cluster posix locks from gfs2 into the dlm
so that it can be used by both gfs2 and ocfs2.
Signed-off-by: David Teigland <teigland@redhat.com>
The RCU iterators used 'rcu_dereference()' on an already-fetched RCU
pointer value, which defeats the whole point of the exercise.
When we dereference a pointer protected by RCU, we need to make sure
that we only fetch the value _once_, because if the compiler ends up
re-loading it due to register pressure, the newly reloaded value could
be different from the previously fetched one, and you get inconsistent
results.
Cleaned-up, fixed, and the pointless list_for_each_safe_rcu #define
deleted by Paul Kenney.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only noticed this while hacking something else, no test case.
blk_max_low_pfn is initialized once at bootup by the block layer from
max_low_pfn. But max_low_pfn is not necessarily constant over the runtime of
the system when you consider memory hotplug. What could happen if that
someone adds memory later the block layer wouldn't get updated and then start
bouncing memory unnecessarily.
Also on 64bit blk_max_low_pfn actually isn't needed because it just disables
bouncing essentially and there is no highmem. And nobody can pass pfns >
max_low_pfn to the block layer, because those wouldn't have a struct page and
I suspect block layer wouldn't be very happy without that.
So set BLK_BOUNCE_HIGH to infinity (-1ULL) on 64bit. That avoids the problem
of having to update it on memory hotadd.
On 32bit I kept the same behaviour because at least on i386
memory hotadd only adds HIGHMEM, never lowmem.
BLK_BOUNCE_ANY is always set to infinity on both 32 and 64bit.
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
blk_rq_map_user adjusts bi_size of the last bio. It breaks the rule
that req->data_len (the true data length) is equal to sum(bio). It
broke the scsi command completion code.
commit e97a294ef6 was introduced to fix
the above issue. However, the partial completion code doesn't work
with it. The commit is also a layer violation (scsi mid-layer should
not know about the block layer's padding).
This patch moves the padding adjustment to blk_rq_map_sg (suggested by
James). The padding works like the drain buffer. This patch breaks the
rule that req->data_len is equal to sum(sg), however, the drain buffer
already broke it. So this patch just restores the rule that
req->data_len is equal to sub(bio) without breaking anything new.
Now when a low level driver needs padding, blk_rq_map_user and
blk_rq_map_user_iov guarantee there's enough room for padding.
blk_rq_map_sg can safely extend the last entry of a scatter list.
blk_rq_map_sg must extend the last entry of a scatter list only for a
request that got through bio_copy_user_iov. This patches introduces
new REQ_COPY_USER flag.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch enables bio_copy_user to take struct sg_iovec (renamed
bio_copy_user_iov). bio_copy_user uses bio_copy_user_iov internally as
bio_map_user uses bio_map_user_iov.
The major changes are:
- adds sg_iovec array to struct bio_map_data
- adds __bio_copy_iov that copy data between bio and
sg_iovec. bio_copy_user_iov and bio_uncopy_user use it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now unregister_cdrom() always returns 0.
Make it return void and update all callers that check the return value.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Use list_head for cdrom_device_info list instead of opencoded
singly list handling.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Most of time_after like macros usages just compare jiffies and another number,
so here add some time_is_* macros for convenience.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Done per Linus' request and suggestions. Linus has explained that
better than I'll be able to explain:
On Thu, Mar 27, 2008 at 10:12:10AM -0700, Linus Torvalds wrote:
> Actually, before we go any further, there might be a less intrusive
> alternative: add just a couple of flags to the resource flags field (we
> still have something like 8 unused bits on 32-bit), and use those to
> implement a generic "resource_alignment()" routine.
>
> Two flags would do it:
>
> - IORESOURCE_SIZEALIGN: size indicates alignment (regular PCI device
> resources)
>
> - IORESOURCE_STARTALIGN: start field is alignment (PCI bus resources
> during probing)
>
> and then the case of both flags zero (or both bits set) would actually be
> "invalid", and we would also clear the IORESOURCE_STARTALIGN flag when we
> actually allocate the resource (so that we don't use the "start" field as
> alignment incorrectly when it no longer indicates alignment).
>
> That wouldn't be totally generic, but it would have the nice property of
> automatically at least add sanity checking for that whole "res->start has
> the odd meaning of 'alignment' during probing" and remove the need for a
> new field, and it would allow us to have a generic "resource_alignment()"
> routine that just gets a resource pointer.
Besides, I removed IORESOURCE_BUS_HAS_VGA flag which was unused for ages.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vital Product Data (VPD) may be exposed by PCI devices in several
ways. It is generally unsafe to read this information through the
existing interfaces to user-land because of stateful interfaces.
This adds:
- abstract operations for VPD access (struct pci_vpd_ops)
- VPD state information in struct pci_dev (struct pci_vpd)
- an implementation of the VPD access method specified in PCI 2.2
(in access.c)
- a 'vpd' binary file in sysfs directories for PCI devices with VPD
operations defined
It adds a probe for PCI 2.2 VPD in pci_scan_device() and release of
VPD state in pci_release_dev().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Each architecture has its own pcibios_enable_resources() implementation.
These differ in many minor ways that have nothing to do with actual
architectural differences. Follow-on patches will make most arches
use this generic version instead.
This version is based on powerpc, which seemed most up-to-date. The only
functional difference from the x86 version is that this uses "!r->parent"
to check for resource collisions instead of "!r->start && r->end".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
#if 0 the no longer used pci_cleanup_aer_correct_error_status().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch finally removes the global list of PCI devices. We are
relying entirely on the list held in the driver core now, and do not
need a separate "shadow" list as no one uses it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets us check if the device is really added to the driver core or
not, which is what we need when walking some of the bus lists. The flag
is there in anticipation of getting rid of the other PCI device list,
which is what we used to check in this situation.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently keep 2 lists of PCI devices in the system, one in the
driver core, and one all on its own. This second list is sorted at boot
time, in "BIOS" order, to try to remain compatible with older kernels
(2.2 and earlier days). There was also a "nosort" option to turn this
sorting off, to remain compatible with even older kernel versions, but
that just ends up being what we have been doing from 2.5 days...
Unfortunately, the second list of devices is not really ever used to
determine the probing order of PCI devices or drivers[1]. That is done
using the driver core list instead. This change happened back in the
early 2.5 days.
Relying on BIOS ording for the binding of drivers to specific device
names is problematic for many reasons, and userspace tools like udev
exist to properly name devices in a persistant manner if that is needed,
no reliance on the BIOS is needed.
Matt Domsch and others at Dell noticed this back in 2006, and added a
boot option to sort the PCI device lists (both of them) in a
breadth-first manner to help remain compatible with the 2.4 order, if
needed for any reason. This option is not going away, as some systems
rely on them.
This patch removes the sorting of the internal PCI device list in "BIOS"
mode, as it's not needed at all anymore, and hasn't for many years.
I've also removed the PCI flags for this from some other arches that for
some reason defined them, but never used them.
This should not change the ordering of any drivers or device probing.
[1] The old-style pci_get_device and pci_find_device() still used this
sorting order, but there are very few drivers that use these functions,
as they are deprecated for use in this manner. If for some reason, a
driver rely on the order and uses these functions, the breadth-first
boot option will resolve any problem.
Cc: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This cleans up the search.c file, now using the pci list of devices that
are created for the driver core, instead of relying on our separate list
of devices. It's better to use the functions already created for this
kind of thing, instead of rolling our own all the time.
This work is done in anticipation of getting rid of that second list of
pci devices all together.
And it ends up saving code, always a nice benefit.
This also removes one compiler warning for when CONFIG_PCI_LEGACY is
enabled as we no longer internally use the deprecated functions anymore.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes the pci_get_device_reverse function as there should not be
any need to walk pci devices backwards anymore. All users of this call
are now gone from the tree, so it is safe to remove it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No one is using this function anymore for quite some time, so remove it.
Everyone calls pci_dev_present() instead anyway...
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An unused function that bloated the kernel only when CONFIG_EMBEDDED was
enabled...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The key expansion routine could be get little more generic, become
a kernel doc entry and then get exported.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Tested-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add kernel-doc notation for ndisc_nodetype:
Warning(linux-2.6.25-git2//include/linux/skbuff.h:340): No description found for parameter 'ndisc_nodetype'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- mark timer_interrupt() static
- sparc_floppy_request_irq() prototype should use irq_handler_t
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
The rearrangements in 945feb174b
("[POWERPC] irqtrace support for 64-bit powerpc") caused 64-bit
non-SMP configs to fail to compile with a message about
local_irq_save being undefined in include/linux/proportions.h.
This follows the lead of x86 in including <linux/irqflags.h> in
asm/system.h, which fixes the problem.
Signed-off-by: Paul Mackerras <paulus@samba.org>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts the main ib_device to use struct device instead of struct
class_device as class_device is going away.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
struct class_device is going away, struct device should be used instead.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After 2.6.24 there was a plan to make the PM core acquire all device
semaphores during a suspend/hibernation to protect itself from
concurrent operations involving device objects. That proved to be
too heavy-handed and we found a better way to achieve the goal, but
before it happened, we had introduced the functions
device_pm_schedule_removal() and destroy_suspended_device() to allow
drivers to "safely" destroy a suspended device and we had adapted some
drivers to use them. Now that these functions are no longer necessary,
it seems reasonable to remove them and modify their users to use the
normal device unregistration instead.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add /sysfs/firmware/ibft/[initiator|targetX|ethernetX] directories along with
text properties which export the the iSCSI Boot Firmware Table (iBFT)
structure.
What is iSCSI Boot Firmware Table? It is a mechanism for the iSCSI tools to
extract from the machine NICs the iSCSI connection information so that they
can automagically mount the iSCSI share/target. Currently the iSCSI
information is hard-coded in the initrd. The /sysfs entries are read-only
one-name-and-value fields.
The usual set of data exposed is:
# for a in `find /sys/firmware/ibft/ -type f -print`; do echo -n "$a: "; cat $a; done
/sys/firmware/ibft/target0/target-name: iqn.2007.com.intel-sbx44:storage-10gb
/sys/firmware/ibft/target0/nic-assoc: 0
/sys/firmware/ibft/target0/chap-type: 0
/sys/firmware/ibft/target0/lun: 00000000
/sys/firmware/ibft/target0/port: 3260
/sys/firmware/ibft/target0/ip-addr: 192.168.79.116
/sys/firmware/ibft/target0/flags: 3
/sys/firmware/ibft/target0/index: 0
/sys/firmware/ibft/ethernet0/mac: 00:11:25:9d:8b:01
/sys/firmware/ibft/ethernet0/vlan: 0
/sys/firmware/ibft/ethernet0/gateway: 192.168.79.254
/sys/firmware/ibft/ethernet0/origin: 0
/sys/firmware/ibft/ethernet0/subnet-mask: 255.255.252.0
/sys/firmware/ibft/ethernet0/ip-addr: 192.168.77.41
/sys/firmware/ibft/ethernet0/flags: 7
/sys/firmware/ibft/ethernet0/index: 0
/sys/firmware/ibft/initiator/initiator-name: iqn.2007-07.com:konrad.initiator
/sys/firmware/ibft/initiator/flags: 3
/sys/firmware/ibft/initiator/index: 0
For full details of the IBFT structure please take a look at:
ftp://ftp.software.ibm.com/systems/support/system_x_pdf/ibm_iscsi_boot_firmware_table_v1.02.pdf
[akpm@linux-foundation.org: fix build]
Signed-off-by: Konrad Rzeszutek <konradr@linux.vnet.ibm.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_is_registered() can use the kobject value for this, so it will
now work with devices that are associated with only a class, not a bus
and a driver.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1058) improves the wakeup macros in include/linux/pm.h.
All but the trivial ones are converted to inline routines, which
requires moving them to a separate header file since they depend on
the definition of struct device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The various wakeup flags and their accessor macros in struct
dev_pm_info should be available whenever CONFIG_PM is enabled, not
just when CONFIG_PM_SLEEP is on. Otherwise remote wakeup won't always
be configurable for runtime power management. This patch (as1056b)
fixes the oversight.
David Brownell adds:
More accurately, fixes the "regression" ... as noted sometime
last summer, after 296699de6b
introduced CONFIG_SUSPEND. But that didn't make the regression
list for that kernel, ergo the delay in fixing it.
[rjw: rebased]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the PM core to protect its data structures, specifically the
dpm_active list, from being corrupted if a child of the currently
suspending device is registered concurrently with its ->suspend()
callback. In that case, since the new device (the child) is added
to dpm_active after its parent, the PM core will attempt to
suspend it after the parent, which is wrong.
Introduce a new member of struct dev_pm_info, called 'sleeping',
and use it to check if the parent of the device being added to
dpm_active has been suspended, in which case the device registration
fails. Also, use 'sleeping' for checking if the ordering of devices
on dpm_active is correct.
Introduce variable 'all_sleeping' that will be set to 'true' once all
devices have been suspended and make new device registrations fail
until 'all_sleeping' is reset to 'false', in order to avoid having
unsuspended devices around while the system is going into a sleep state.
Remove pm_sleep_rwsem which is not necessary any more.
Special thanks to Alan Stern for discussions and suggestions that
lead to the creation of this patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert sysfs_remove_bin_file() to have a return type of 'void' for
!CONFIG_SYSFS configurations. Also removes unnecessary colons from empty
void functions.
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When DEBUG is not defined, pr_debug and dev_dbg and some
other local debugging functions are specified as:
"inline __attribute__((format (printf, x, y)))"
This is done to validate printk arguments when not debugging.
Converting these functions to macros or statement expressions
"do { if (0) printk(fmt, ##arg); } while (0)"
or
"({ if (0) printk(fmt, ##arg); 0; })
makes at least gcc 4.2.2 produce smaller objects.
This has the additional benefit of allowing the optimizer to
avoid calling functions like print_mac that might have been
arguments to the printk.
defconfig x86 current:
$ size vmlinux
text data bss dec hex filename
4716770 474560 618496 5809826 58a6a2 vmlinux
all converted: (More patches follow)
$ size vmlinux
text data bss dec hex filename
4716642 474560 618496 5809698 58a622 vmlinux
Even kernel/sched.o, which doesn't even use these
functions, becomes smaller.
It appears that merely having an indirect include
of <linux/device.h> can cause bigger objects.
$ size sched.inline.o sched.if0.o
text data bss dec hex filename
31385 2854 328 34567 8707 sched.inline.o
31366 2854 328 34548 86f4 sched.if0.o
The current preprocessed only kernel/sched.i file contains:
# 612 "include/linux/device.h"
static inline __attribute__((always_inline)) int __attribute__ ((format (printf, 2, 3)))
dev_dbg(struct device *dev, const char *fmt, ...)
{
return 0;
}
# 628 "include/linux/device.h"
static inline __attribute__((always_inline)) int __attribute__ ((format (printf, 2, 3)))
dev_vdbg(struct device *dev, const char *fmt, ...)
{
return 0;
}
Removing these unused inlines from sched.i shrinks sched.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Mon, Apr 14, 2008 at 03:36:24PM +0100, Alan Cox wrote:
> On Mon, 14 Apr 2008 17:17:21 +0300
> Adrian Bunk <bunk@kernel.org> wrote:
>
> > This patch fixes the following build error:
> >
> > <-- snip -->
> >
> > ...
> > CC [M] drivers/serial/8250.o
> > /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/serial/8250.c:95:24: error: asm/serial.h: No such file or directory
> > make[3]: *** [drivers/serial/8250.o] Error 1
> >
> > <-- snip -->
> >
> > Signed-off-by: Adrian Bunk <bunk@kernel.org>
> >
> > ---
> > 3cb4ef80d75e118ccfd44f7006aea3db54afb31c diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
> > index b1bbaa0..b0e216d 100644
> > --- a/drivers/serial/Kconfig
> > +++ b/drivers/serial/Kconfig
> > @@ -11,7 +11,7 @@ menu "Serial drivers"
> > # The new 8250/16550 serial drivers
> > config SERIAL_8250
> > tristate "8250/16550 and compatible serial support"
> > - depends on (BROKEN || !SPARC)
> > + depends on (BROKEN || !SPARC) && !AVR32
> > select SERIAL_CORE
> > ---help---
>
> NAK.
>
> Add an asm/serial.h to the platform as it has PCI so will have 8250 PCI
> devices available to it. A copy of the MIPS one should be right.
Patch below.
> Alan
cu
Adrian
<-- snip -->
This patch fixes the following build error with CONFIG_SERIAL_8250:
<-- snip -->
...
CC [M] drivers/serial/8250.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/serial/8250.c:95:24: error: asm/serial.h: No such file or directory
make[3]: *** [drivers/serial/8250.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch fixes the following compile error with CONFIG_MD_RAID456
on avr32:
<-- snip -->
...
CC [M] crypto/xor.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/crypto/xor.c:23:21: error: asm/xor.h: No such file or directory
/home/bunk/linux/kernel-2.6/git/linux-2.6/crypto/xor.c: In function 'calibrate_xor_blocks':
/home/bunk/linux/kernel-2.6/git/linux-2.6/crypto/xor.c:131: error: 'XOR_TRY_TEMPLATES' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/git/linux-2.6/crypto/xor.c:131: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/git/linux-2.6/crypto/xor.c:131: error: for each function it appears in.)
make[2]: *** [crypto/xor.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This combines three patches from David Brownell:
* avr32: tclib support
* avr32: simplify clocksources
* avr32: Turn count/compare into a oneshot clockevent device
Register both TC blocks (instead of just the first one) so that
the AT32/AT91 tclib code will pick them up (instead of just the
avr32-only PIT-style clocksource).
Rename the first one and its resources appropriately.
More cleanups to the cycle counter clocksource code
- Disable all the weak symbol magic; remove the AVR32-only TCB-based
clocksource code (source and header).
- Mark the __init code properly.
- Don't forget to report IRQF_TIMER.
- Make the system work properly with this clocksource, by preventing
use of the CPU "idle" sleep state in the idle loop when it's used.
Package the avr32 count/compare timekeeping support as a oneshot
clockevent device, so it supports NO_HZ and high res timers.
This means it also supports plugging in other clockevent devices
and clocksources.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Create a new file, pm-at32ap700x.S, in mach-at32ap and move the CPU
idle sleep code there. Make it possible to disable the sleep code.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Move the only thing that was actually implemented and used in
asm/intc.h, intc_get_pending(), into asm/irq.h and delete asm/intc.h
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
New-style I2C drivers require that motherboard-mounted I2C devices are
registered with the I2C core, typically at arch_initcall time. This
can be done nice and neat by passing the struct i2c_board_info[]
through at32_add_device_twi just like we do for the SPI board info.
While we've got the hood up, remove a duplicate declaration of
at32_add_device_twi() in board.h.
[hskinnemoen@atmel.com: add missing i2c_board_info forward-declaration]
Signed-Off-By: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
PAGE_SIZE is used both from assembly and C code. We want to have type
specifiers when using it from C, but this will make the assembler
confused, so we need to make it conditional.
This is exactly what the _AC macro is for, so using it allows us to
get rid of a few lines of cpp noise.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
NFSv4 requires us to ensure that we break the TCP connection before we're
allowed to retransmit a request. However in the case where we're
retransmitting several requests that have been sent on the same
connection, we need to ensure that we don't interfere with the attempt to
reconnect and/or break the connection again once it has been established.
We therefore introduce a 'connection' cookie that is bumped every time a
connection is broken. This allows requests to track if they need to force a
disconnection.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We need to try to ensure that we always use the same credentials whenever
we re-establish the clientid on the server. If not, the server won't
recognise that we're the same client, and so may not allow us to recover
state.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
With the recent change to generic creds, we can no longer use
cred->cr_ops->cr_name to distinguish between RPCSEC_GSS principals and
AUTH_SYS/AUTH_NULL identities. Replace it with the rpc_authops->au_name
instead...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When we replace the existing synchronous RPC calls with asynchronous calls,
the reference count will be needed in order to allow us to examine the
result of the RPC call.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
It is quite possible that the OPEN, CLOSE, LOCK, LOCKU,... compounds fail
before the actual stateful operation has been executed (for instance in the
PUTFH call). There is no way to tell from the overall status result which
operations were executed from the COMPOUND.
The fix is to move incrementing of the sequence id into the XDR layer,
so that we do it as we process the results from the stateful operation.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The rest of the networking layer uses SOCK_ASYNC_NOSPACE to signal whether
or not we have someone waiting for buffer memory. Convert the SUNRPC layer
to use the same idiom.
Remove the unlikely()s in xs_udp_write_space and xs_tcp_write_space. In
fact, the most common case will be that there is nobody waiting for buffer
space.
SOCK_NOSPACE is there to tell the TCP layer whether or not the cwnd was
limited by the application window. Ensure that we follow the same idiom as
the rest of the networking layer here too.
Finally, ensure that we clear SOCK_ASYNC_NOSPACE once we wake up, so that
write_space() doesn't keep waking things up on xprt->pending.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
De-couple load-balancing from the rb-trees, so that I can change their
organization.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the group hierarchy can have an arbitrary depth the O(n^2) nature
of RT task dequeues will really hurt. Optimize this by providing space to
store the tree path, so we can walk it the other way.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Implement SMP nice support for the full group hierarchy.
On each load-balance action, compile a sched_domain wide view of the full
task_group tree. We compute the domain wide view when walking down the
hierarchy, and readjust the weights when walking back up.
After collecting and readjusting the domain wide view, we try to balance the
tasks within the task_groups. The current approach is a naively balance each
task group until we've moved the targeted amount of load.
Inspired by Srivatsa Vaddsgiri's previous code and Abhishek Chandra's H-SMP
paper.
XXX: there will be some numerical issues due to the limited nature of
SCHED_LOAD_SCALE wrt to representing a task_groups influence on the
total weight. When the tree is deep enough, or the task weight small
enough, we'll run out of bits.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Abhishek Chandra <chandra@cs.umn.edu>
CC: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[rebased for sched-devel/latest]
- Add a new cpuset file, having levels:
sched_relax_domain_level
- Modify partition_sched_domains() and build_sched_domains()
to take attributes parameter passed from cpuset.
- Fill newidle_idx for node domains which currently unused but
might be required if sched_relax_domain_level become higher.
- We can change the default level by boot option 'relax_domain_level='.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
UID grouping doesn't actually have a task_group representing the root of
the task_group tree. Add one.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch makes the group scheduler multi hierarchy aware.
[a.p.zijlstra@chello.nl: rt-parts and assorted fixes]
Signed-off-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a new function that accepts a pointer to the "newly allowed cpus"
cpumask argument.
int set_cpus_allowed_ptr(struct task_struct *p, const cpumask_t *new_mask)
The current set_cpus_allowed() function is modified to use the above
but this does not result in an ABI change. And with some compiler
optimization help, it may not introduce any additional overhead.
Additionally, to enforce the read only nature of the new_mask arg, the
"const" property is migrated to sub-functions called by set_cpus_allowed.
This silences compiler warnings.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Add cpu_sysdev_class functions to display the following maps
with cpulist_scnprintf().
cpu_online_map
cpu_present_map
cpu_possible_map
* Small change to include/linux/sysdev.h to allow the attribute
name and label to be different (to avoid collision with the
"attr_online" entry for bringing cpus on- and off-line.)
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Here is a simple patch to use an allocated array of cpumasks to
represent cpumask_of_cpu() instead of constructing one on the stack.
It's based on the Kconfig option "HAVE_CPUMASK_OF_CPU_MAP" which is
currently only set for x86_64 SMP. Otherwise the the existing
cpumask_of_cpu() is used but has been changed to produce an lvalue
so a pointer to it can be used.
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Add a static cpumask_t variable "CPU_MASK_ALL_PTR" to use as
a pointer reference to CPU_MASK_ALL. This reduces where possible
the instances where CPU_MASK_ALL allocates and fills a large
array on the stack. Used only if NR_CPUS > BITS_PER_LONG.
* Change init/main.c to use new set_cpus_allowed_ptr().
Depends on:
[sched-devel]: sched: add new set_cpus_allowed_ptr function
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Remove empty cpumask_t (and all non-zero/non-null) variables
in SD_*_INIT macros. Use memset(0) to clear. Also, don't
inline the initializer functions to save on stack space in
build_sched_domains().
* Merge change to include/linux/topology.h that uses the new
node_to_cpumask_ptr function in the nr_cpus_node macro into
this patch.
Depends on:
[mm-patch]: asm-generic-add-node_to_cpumask_ptr-macro.patch
[sched-devel]: sched: add new set_cpus_allowed_ptr function
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* Modify sched_affinity functions to pass cpumask_t variables by reference
instead of by value.
* Use new set_cpus_allowed_ptr function.
Depends on:
[sched-devel]: sched: add new set_cpus_allowed_ptr function
Cc: Paul Jackson <pj@sgi.com>
Cc: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Christian Limpach
Markus Armbruster
Isaku Yamahata
Jeremy Fitzhardinge
Ingo Molnar
Linus Torvalds
venkatesh.pallipadi@intel.com
Arjan van de Ven
Trond Myklebust
Dmitry Torokhov
Dmitry Belimov
Douglas Schilling Landgraf
Steven Toth
Mauro Carvalho Chehab
Janne Grunau
Dâniel Fraga
Guennadi Liakhovetski
Brandon Philips
Frej Drejhammar
Michael Krufky
Peter Hartley
Steven Whitehouse
Brandon Philips
Ishizaki Kou
Tony Breeds
Kumar Gala
Josh Boyer
Benjamin Herrenschmidt
Paul Mackerras
Takashi Iwai
David S. Miller
Pavel Machek
Pavel Hofman
Pawel MOLL
Patrick McHardy
Luis Carlos Cobo
Chuck Lever
Steven Whitehouse
Jeff Layton
Robert P. J. Day
Kevin Coffman
Harvey Harrison
J. Bruce Fields
Aurélien Charbon
Yevgeny Petrilin
David Woodhouse
Ram Pai
Miklos Szeredi
Dean Nelson
Ben Dooks
Manuel Lauss
Wolfram Sang
FUJITA Tomonori
James Bottomley
Florian Fainelli
eric miao
Hidetoshi Seto
Adrian Bunk
Mike Frysinger
Oliver Neukum
Anssi Hannula
Jiri Slaby
Jiri Kosina
Jim Duchek
Pekka Sarnila
Herbert Xu
Al Viro
Randy Dunlap
Sebastian Siewior
Johannes Weiner
Tobias Klauser
David Teigland
Andi Kleen
Akinobu Mita
Dave Young
Ivan Kokshaysky
Ben Hutchings
Bjorn Helgaas
Shaohua Li
Greg Kroah-Hartman
Sebastian Siewior
Jeff Garzik
Tony Jones
Rafael J. Wysocki
Konrad Rzeszutek
Alan Stern
David Rientjes
Joe Perches
Daniel Walker
David Brownell
Haavard Skinnemoen
Ben Nizette
Cyrill Gorcunov
Haavard Skinnemoen
Peter Zijlstra
Dhaval Giani
Mike Travis