ST Micro variants has some specific dma burst threshold compensation,
which allows them to make better use of a DMA controller. Add support
to set this up.
Based on a patch from Linus Walleij.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add DMA engine support for transmit to the PL011 driver. Based on a
patch from Linus Walliej, with the following changes:
- remove RX DMA support. As PL011 doesn't give us receive timeout
interrupts, we only get notified of received data when the RX DMA
has completed. This rather sucks for interactive use of the TTY.
- remove abuse of completions. Completions are supposed to be for
events, not to tell what condition buffers are in. Replace it with
a simple 'queued' bool.
- fix locking - it is only safe to access the circular buffer with the
port lock held.
- only map the DMA buffer when required - if we're ever behind an IOMMU
this helps keep IOMMU usage down, and also ensures that we're legal
when we change the scatterlist entry length.
- fix XON/XOFF sending - we must send XON/XOFF characters out as soon
as possible - waiting for up to 4095 characters in the DMA buffer
to be sent first is not acceptable.
- fix XON/XOFF receive handling - we need to stop DMA when instructed
to by the TTY layer, and restart it again when instructed to. There
is a subtle problem here: we must not completely empty the circular
buffer with DMA, otherwise we will not be notified of XON.
- change the 'enable_dma' flag into a 'using DMA' flag, and track
whether we can use TX DMA by whether the channel pointer is non-NULL.
This gives us more control over whether we use DMA in the driver.
- we don't need to have the TX DMA buffer continually allocated for
each port - instead, allocate it when the port starts up, and free
it when it's shut down. Update the 'using DMA' flag if we get
the buffer, and adjust the TTY FIFO size appropriately.
- if we're going to use PIO to send characters, use the existing IRQ
based functionality rather than reimplementing it. This also ensures
we call uart_write_wakeup() at the appropriate time, otherwise we'll
stall.
- use DMA engine helper functions for type safety.
- fix init when built as a module - we can't have to initcall functions,
so we must settle on one. This means we can eliminate the deferred
DMA initialization.
- there is no need to terminate transfers on a failed prep_slave_sg()
call - nothing has been setup, so nothing needs to be terminated.
This avoids a potential deadlock in the DMA engine code
(tasklet->callback->failed prepare->terminate->tasklet_disable
which then ends up waiting for the tasklet to finish running.)
- Dan says that the submission callback should not return an error:
| dma_submit_error() is something I should have removed after commit
| a0587bcf "ioat1: move descriptor allocation from submit to prep" all
| errors should be notified by prep failing to return a descriptor
| handle. Negative dma_cookie_t values are only returned by the
| dma_async_memcpy* calls which translate a prep failure into -ENOMEM.
So remove the error handling at that point. This also solves the
potential deadlock mentioned in the previous comment.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As the DMA support introduces a separate interrupt-time callback, our
interrupt handler will not be the only handler which takes the port
lock, so we need to ensure that IRQs are disabled. We must use the
_irqsave variant so we don't inadvertently enable interrupts.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With DMA support, we need to tell the TTY subsystem that the DMA buffer
is the size of the FIFO, otherwise things like tty_wait_until_sent()
will time out too early. Keep (and use) the hardware value separately
from the port->fifosize.
This was part of a larger patch from Linus Walleij, with a little
modification.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than copying all vendor data into the port structure, copy
just that which is frequently used, and keep a pointer to the
remaining vendor data structure. This makes it easier to add
vendor quirks in the future.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The error flags weren't being cleared upon UART startup, which
can cause problems when we add DMA support. It's good practice
to ensure that these flags are cleared anyway, so let's do so.
This was part of a larger patch from Linus Walleij.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Include the revision number of the PL011 primecell in the boot-time
port printk to allow proper identification of the peripheral.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Not accessed outside builtin-script, so make them static.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
That already does what was being done here. The warning is now unconditionally
given by __perf_session__process_pipe_events, just like for non pipe processing.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Just like we do at __perf_session__process_events
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch fixes the usage of the perf_event.h header file
between command modules and the supporting code in util.
It is necessary to ensure that ALL files use the SAME
perf_event.h header from the kernel source tree.
There were a couple of #include <linux/perf_event.h> mixed
with #include "../../perf_event.h".
This caused issues on some distros because of mismatch
in the layout of struct perf_event_attr. That eventually
led perf stat to segfault.
Cc: David S. Miller <davem@davemloft.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@gmail.com>
LKML-Reference: <4d233cf0.2308e30a.7b00.ffffc187@mx.google.com>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Rebooted my devel machine, first thing I ran was perf test, that expects
debugfs to be mounted, test fails. Be more clear about it.
Also add missing newlines and add more informative message when
sys_perf_event_open fails.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
drivers/staging/cx25821/cx25821-video.c: In function ‘video_open’:
drivers/staging/cx25821/cx25821-video.c:817:8: error: implicit declaration of function ‘lock_kernel’
drivers/staging/cx25821/cx25821-video.c:834:9: error: implicit declaration of function ‘unlock_kernel’
This patch just adds a header with BKL function. It should be enough
to avoid compilation breakage, but, as BKL will be removed, we need
to properly fix it on a latter patch.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Reported-by: Anca Emanuel <anca.emanuel@gmail.com>
Cc: Palash Bandyopadhyay <Palash.Bandyopadhyay@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prevent the long delay in io_check_error making NMI watchdog
timeout.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
LKML-Reference: <1294198689-15447-3-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The spin_lock_debug/rcu_cpu_stall detector uses
trigger_all_cpu_backtrace() to dump cpu backtrace.
Therefore it is possible that trigger_all_cpu_backtrace()
could be called at the same time on different CPUs, which
triggers and 'unknown reason NMI' warning. The following case
illustrates the problem:
CPU1 CPU2 ... CPU N
trigger_all_cpu_backtrace()
set "backtrace_mask" to cpu mask
|
generate NMI interrupts generate NMI interrupts ...
\ | /
\ | /
The "backtrace_mask" will be cleaned by the first NMI interrupt
at nmi_watchdog_tick(), then the following NMI interrupts
generated by other cpus's arch_trigger_all_cpu_backtrace() will
be taken as unknown reason NMI interrupts.
This patch uses a test_and_set to avoid the problem, and stop
the arch_trigger_all_cpu_backtrace() from calling to avoid
dumping a double cpu backtrace info when there is already a
trigger_all_cpu_backtrace() in progress.
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Reviewed-by: Bruce Ashfield <bruce.ashfield@windriver.com>
Cc: fweisbec@gmail.com
LKML-Reference: <1294198689-15447-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Don Zickus <dzickus@redhat.com>
There are some paths that walk the die_chain with preemption on.
Make sure we are in an NMI call before we start doing anything.
This was triggered by do_general_protection calling notify_die
with DIE_GPF.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Don Zickus <dzickus@redhat.com>
LKML-Reference: <1294198689-15447-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
wait_for_completion_*_timeout() can return:
0: if the wait timed out
-ve: if the wait was interrupted
+ve: if the completion was completed.
As they currently return an 'unsigned long', the last two cases
are not easily distinguished which can easily result in buggy
code, as is the case for the recently added
wait_for_completion_interruptible_timeout() call in
net/sunrpc/cache.c
So change them both to return 'long'. As MAX_SCHEDULE_TIMEOUT
is LONG_MAX, a large +ve return value should never overflow.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: J. Bruce Fields <bfields@fieldses.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110105125016.64ccab0e@notabene.brown>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Found one x2apic pre-enabled system, x2apic_mode suddenly get
corrupted after register some cpus, when compiled
CONFIG_NR_CPUS=255 instead of 512.
It turns out that generic_processor_info() ==> phyid_set(apicid,
phys_cpu_present_map) causes the problem.
phys_cpu_present_map is sized by MAX_APICS bits, and pre-enabled
system some cpus have an apic id > 255.
The variable after phys_cpu_present_map may get corrupted
silently:
ffffffff828e8420 B phys_cpu_present_map
ffffffff828e8440 B apic_verbosity
ffffffff828e8444 B local_apic_timer_c2_ok
ffffffff828e8448 B disable_apic
ffffffff828e844c B x2apic_mode
ffffffff828e8450 B x2apic_disabled
ffffffff828e8454 B num_processors
...
Actually phys_cpu_present_map is referenced via apic id, instead
index. We should use MAX_LOCAL_APIC instead MAX_APICS.
For 64-bit it will be 32768 in all cases. BSS will increase by 4k bytes
on 64-bit:
text data bss dec filename
21696943 4193748 12787712 38678403 vmlinux.before
21696943 4193748 12791808 38682499 vmlinux.after
No change on 32bit.
Finally we can remove MAX_APCIS that was rather confusing.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <4D23BD9C.3070102@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the seqfile /proc/cpuinfo gets accesses for each possible cpu
loops_per_jiffy gets recalculated. However its value is only needed
on first access.
In addition loops_per_jiffy should be recalculated when the machine
reports a capability change.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use get_online_cpus() instead of preempt_disable() to make sure cpus
don't go offline while accessing their per cpu data.
The preempt_disable() stuff is old code which was used before
get_online_cpus() was available.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of messages that indicate if a cpu went online or offline.
There is nothing special about this anymore and these messages might
flood the kernel log buffer which makes debugging harder since more
important messages might be overwritten.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This enables the spinning mutex feature on s390 by removing
HAVE_DEFAULT_NO_SPIN_MUTEXES from arch/s390/Kconfig.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The spinning mutex implementation uses cpu_relax() in busy loops as a
compiler barrier. Depending on the architecture, cpu_relax() may do more
than needed in this specific mutex spin loops. On System z we also give
up the time slice of the virtual cpu in cpu_relax(), which prevents
effective spinning on the mutex.
This patch replaces cpu_relax() in the spinning mutex code with
arch_mutex_cpu_relax(), which can be defined by each architecture that
selects HAVE_ARCH_MUTEX_CPU_RELAX. The default is still cpu_relax(), so
this patch should not affect other architectures than System z for now.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1290437256.7455.4.camel@thinkpad>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A race condition exists in the ccwgroup device unregistration code
which can cause a kernel panic due to a use-after-free bug. This
race condition might be triggered when all ccw devices associated with
a ccwgroup device are removed at the same time (e.g. because the
corresponding channel path becomes no longer available).
Fix this race condition by clearing the references from the associated
ccw devices to the ccw group device during unregistration of the
ccw group device.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Call init_idle() which (re-)initializes the idle task structure before
it gets used on a new cpu.
That way we can also get rid of the odd preempt_enable_no_resched()
call we have in the cpu offline path within cpu_idle(). That call
prevented preempt count imbalances between cpu hotplug operations.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Delay idle task creation until a cpu gets set online instead of
creating them for all possible cpus at system startup.
For one cpu system this should safe more than 1 MB.
On my debug system with lots of debug stuff enabled this saves 2 MB.
Same as on x86.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case the DASD driver needs to term a running I/O the retry counter
is decreased twice.
Remove the unnecessary retry counter decrease in das_term_IO.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Normal I/O operations through the DASD device driver give only access
to the data fields of an ECKD device even for track based I/O.
This patch extends the DASD device driver to give access to whole
ECKD tracks including count, key and data fields.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The freeze callback may set a stop bit so that a worker thread could
not start I/O. The discipline specific freeze function waits for the
worker to be completed.
Set the stop_bit after the discipline specific freeze function has
returned and no worker is running.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a DASD device has been reserved by a Linux system, and later
this reservation is ‘stolen’ by a second system by means of an
unconditional reserve, then the first system receives a
notification about this fact. With this patch such an event can
be either ignored, as before, or it can be used to let the device
fail all I/O request, so that the device will not block anymore.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a new path is added at runtime, the CIO layer will call the drivers
path_event callback. The DASD device driver uses this callback to trigger
a path verification for the new path. The driver will use only those
paths for I/O, which have been successfully verified.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some storage systems support multitrack High Performance FICON
requests, which read or write data to more than one track.
This patch enables the DASD device driver to generate multitrack
High Performance FICON requests.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Any list of indirect data adresses (TIDAL) used by a TCW must not
cross a page boundary. The original itcw implementation complies with
this restriction by allocating allmost twice as much memory as
actually needed, so that in any case there is enough room for the full
TIDAL, either above or below the page boundary.
This patch implements an alternative method, by using a TTIC TIDAW to
connect TIDAL parts below and above a page boundary.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Until now machine checks for the swapper process of the IPL cpu are just
implicitly (and more or less accidently) enabled when the first time the
idle process goes into idle state and loads an enabled wait psw.
Before that machine checks are disabled.
So let's enable them explicitly in trap_init() so we have a well defined
time when machine checks are enabled.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The used buffers counter is not incremented in case of an error so
the counter can become negative. Increment the used buffers counter
before checking for errors.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Update the subchannel descriptor if we receive a
"Installed parameters modified" crw.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make the code in the 31 bit entry.S code as similar as possible to the
64 bit version in entry64.S. That makes it easier to add new code to
the first level interrupt handler that affects both 31 and 64 bit kernels.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support to accumulate the number of 64K-bytes blocks all paths
to a device at least support for a transport command.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
arch_needs_cpu() gets always executed on the current cpu. Therefore
the cpu parameter can be ignored it is possible to use __get_cpu_var()
instead of per_cpu() to access the per_cpu variable, which will
generate better code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Simplify the SIGA sync code and add unlikely annotations. In polling mode
SBALs may be accessed without interrupt, so call SIGA sync before every scan.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
HiperSocket devices only use one SBAL per qdio call without the enhanced SIGA
feature. Since that feature is currently not used remove it from the qdio code
so the compiler can generate better code for the HiperSocket outbound path.
While at it mark the SIGA error conditions as unlikely.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
John W. Linville
Russell King
Arnaldo Carvalho de Melo
Stephane Eranian
Mauro Carvalho Chehab
Huang Ying
Dongdong Deng
Don Zickus
Ingo Molnar
NeilBrown
Yinghai Lu
Heiko Carstens
Gerald Schaefer
Peter Oberparleiter
Martin Schwidefsky
Stefan Haberland
Stefan Weinhuber
Jan Glauber
Sebastian Ott