There's no reason for this to be in the header, and it just hurts
recompile time.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Max Krasnyanskiy <maxk@qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver stores the PCI resource addresses into 'unsigned long' variable
before calling ioremap_nocache() on them. This warrants kernel oops when the
registers are accessed on PPC 44x platforms which (being 32-bit) have PCI
memory space mapped beyond 4 GB.
The arch/ppc/ kernel has a fixup in ioremap() that creates an illusion that
the PCI memory resource is mapped below 4 GB, but arch/powerpc/ code got rid
of this trick, having instead CONFIG_RESOURCES_64BIT enabled.
[ Bump driver version and release date -DaveM ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP support in generic HDLC in Linux 2.6.25 is broken and will cause
a kernel panic when a device configured in PPP mode is activated.
It will be replaced by new PPP implementation after Linux 2.6.25 is
released.
This affects only PPP support in generic HDLC (mostly Hitachi SCA
and SCA-II based drivers, wanxl, and few others). Standalone syncppp
and async PPP support are not affected.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch fixes two weaknesses in send/receive packet handling which may
lead to kernel panics during DLPAR memory add operations.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This critical patch fixes a mac address issue recently introduced. If the
device's mac address was in correct order and the flag
NVREG_TRANSMITPOLL_MAC_ADDR_REV was set, during nv_remove the flag would get
cleared. During next load, the mac address would get reversed because the
flag is missing.
As it has been indicated previously, the flag is cleared across a low power
transition. Therefore, the driver should set the mac address back into the
reversed order when clearing the flag.
Also, the driver should set back the flag after a low power transition to
protect against kexec command calling nv_probe a second time.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: "Yinghai Lu" <yhlu.kernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Call phy_disconnect() on remove routine. Otherwise the phy timer
causes a kernel crash when unloading.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The new Fixed PHY method, fixed-link property, isn't
impl. for ucc_geth which makes fixed PHYs non functional.
Add support for the new method to restore the Fixed PHY
functionality.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Any usage of sky2 on new Yukon Supreme would cause a NULL dereference.
The chip is very new, so the support is still untested; vendor has
not sent any eval hardware.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[NETNS][IPV6] tcp - assign the netns for timewait sockets
[IPV4]: Fix byte value boundary check in do_ip_getsockopt().
BNX2X: Correct bringing chip out of reset
[NETFILTER]: nf_nat: autoload IPv4 connection tracking
[NETFILTER]: xt_hashlimit: fix mask calculation
[XFRM]: xfrm_user: fix selector family initialization
rt61pci: rt61pci_beacon_update do not free skb twice
ssb-mipscore: Fix interrupt vectors
ssb-pcicore: Fix IRQ TPS flag handling
mac80211: use short_preamble mode from capability if ERP IE not present
[NET]: Undo code bloat in hot paths due to print_mac().
[TCP]: Don't allow FRTO to take place while MTU is being probed
[TCP]: tcp_simple_retransmit can cause S+L
[TCP]: Fix NewReno's fast rexmit/recovery problems with GSOed skb
[TCP]: Restore 2.6.24 mark_head_lost behavior for newreno/fack
nl80211: fix STA AID bug
b43legacy: fix bcm4303 crash
iwlwifi: fix n-band association problem
ipw2200: set MAC address on radiotap interface
libertas: fix mode initialization problem
Fixed bug: Wrong register was written to when bringing the chip out of
reset.
[ Bump driver version and release date -DaveM ]
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The layer above will free the skb in an error case.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If print_mac() is used inside of a pr_debug() the compiler
can't see that the call is redundant so still performs it
even of pr_debug() ends up being a nop.
So don't use print_mac() in such cases in hot code paths,
use MAC_FMT et al. instead.
As noted by Joe Perches, pr_debug() could be modified to
handle this better, but that is a change to an interface
used by the entire kernel and thus needs to be validated
carefully. This here is thus the less risky fix for
2.6.25
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames all mac80211 files (except ieee80211_i.h) to get rid
of the useless ieee80211_ prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must use the b43_is_mode() call to check the current interface
operation mode.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the initialization of the PHY TX control words in
shared memory. These control words are used for management frames
like beacons.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes beacon updating in the bottomhalf.
In case the device is busy, we will defer to later in the IRQ handler.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new API to MAC80211 to allow low level driver to
notify MAC with driver status.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are some beaconing related fixes. Basically it prevents
the card from triggering the beacon IRQ over and over again.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When doing firmware-assisted scanning, iwlwifi drivers do not
honour the regulatory control code that might disable channels
that are enabled in the EEPROM, for example when the user is
visiting another country and adjusted the regulatory domain
accordingly. This patch fixes that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not free reference to device twice. After rfkill registration succeeds
we only need to call rfkill_unregister() and not rfkill_free().
Also add some debugging.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the workqueue is notified the LED code may be accessed. Ensure
that LED registration completes completely as part of initialization
before anything waiting on this is notified.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces ieee80211chan2mhz from radiotap with
ieee80211_frequency_to_channel provided by mac80211
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves inline functions into iwl-core.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make some cleanup in HW names
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now rt2x00lib handles the initial configure_filter() command, we can
directly call lib->config_filter() in scheduled context since the
called function will no longer check if anything has changed (which is
now handled in rt2x00lib as well).
This fixes a endless loop with USB drivers where the config_filter
command was scheduled time and time again without sending any command
to the device.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some timings for pre-TBTT and synthetic PU.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some minor stuff for N-PHY support. Nothing special.
Adds Analog switching and some TODOs for RSSI processing.
Just a patch I had floating around for quite some time now.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This changes the b43-PIO code to use the new SSB block-I/O.
This reduces the overhead by removing lots of function calls, pointer
dereferencing, if-conditionals any byteswapping for each packet data word.
This also fixes a harmless sparse endianness warning.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix error reported by Miles Lane <miles.lane@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was used only at one place anyway.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... as it has nothing to do with pure association
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Besides code moving, I did the following changes:
* made some functions static
* removed some unneeded #include's
* made patch checkpatch.pl clean
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Besides code moving, I did the following changes:
* made some functions static
* removed some unneeded #include's
* made patch checkpatch.pl clean
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Select IWLWIFI_LEDS automatically when either IWL3945_LEDS or
IWL4965_LEDS is selected. This avoids potential misconfigurations
which lead to build failures for iwl-led.c.
Cc: Miles Lane <miles.lane@gmail.com>
Cc: reinette.chatre@intel.com
Signed-off-by: John w. Linville <linville@tuxdriver.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes all kinds of warnings in iwlwifi.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl-debugfs.c: In function ‘iwl_dbgfs_stations_read’:
drivers/net/wireless/iwlwifi/iwl-debugfs.c:247: warning: format ‘%llu’ expects type ‘long long unsigned int’, but argument 4 has type ‘u64’
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hi John,
Can you please take a look at this patch?
drivers/net/wireless/wavelan_cs.c has unusually large number
of static inline functions - 27.
I looked through them and 20 of them do not seem to warrant inlining.
Some are really big; others call mdelay(1) or busy-wait for a bit
to be set in a hardware register - it's pointless
to optimize such functions for speed.
This patch removes "inline" from these static function
(regardless of number of callsites - gcc nowadays auto-inlines
statics with one callsite).
Size difference for 32bit x86:
text data bss dec hex filename
17020 372 8 17400 43f8 linux-2.6-ALLYES/drivers/net/wireless/wavelan_cs.o
14032 356 8 14396 383c linux-2.6.inline-ALLYES/drivers/net/wireless/wavelan_cs.o
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
--
vda
Signed-off-by: John W. Linville <linville@tuxdriver.com>
> prism54 should set the carrier flags correctly when it thinks the
> link can be used.
Agreed, so sure, this is OK but I rather we turn the carrier on
or off *before* sending an event, like this.
Signed-off-by: Roy Marples <uberlord@gentoo.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turn the SSB bus suspend mechanism upside down.
Instead of deciding by an internal reference count when to suspend/resume,
let the parent bus call us in their suspend/resume routine.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds PIO support back (D'oh!) for PCMCIA devices.
This is a complete rewrite of the old PIO code. It does actually work
and we get reasonable performance out of it on a modern machine.
On a PowerBook G4 I get a few MBit for TX and a few more for RX.
So it doesn't work as well as DMA (of course), but it's a _lot_ faster
than the old PIO code (only got a few kBit with that).
The limiting factor is the host CPU speed. So it will generate 100%
CPU usage when the network interface is heavily loaded. A voluntary preemption
point in the RX path makes sure Desktop Latency isn't hurt.
PIO is needed for 16bit PCMCIA devices, as we really don't want to poke with
the braindead DMA mechanisms on PCMCIA sockets. Additionally, not all
PCMCIA sockets do actually support DMA in 16bit mode (mine doesn't).
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes association from beacon
using bss_info_change handler for association
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch eliminates the use of conf_ht in iwlwifi driver, replacing it
with bss_info_changed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables the IWL4965_HT flag (n-band) in Kconfig.
Removed the "depends on n" from Kconfig for config IWL4965_HT
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit bada339ba2 enforces that all
interfaces have a valid MAC address before they are brought up.
ipw2200 does not assign a MAC address to it's radiotap interface, meaning
that the radiotap interface cannot be brought up in 2.6.24.
https://bugs.gentoo.org/show_bug.cgi?id=215714
Fix this by copying the MAC address from the real interface.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After moving lbs_find_best_network_ssid() from scan.c to assoc.c gcc was
able to deduce that new_mode might stay uninitialized.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'disable_cb' is really just a hint and as such, it's possible for more
work to get queued up while callbacks are disabled. Under stress with an
SMP guest, this printk triggers very frequently. There is no race here, this
is how things are designed to work so let's just remove the printk.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 9e6db60825, which was
merged without the API it needed, causing build breakage.
Reported-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
fix endian lossage in forcedeth
net/tokenring/olympic.c section fixes
net: marvell.c fix sparse shadowed variable warning
[VLAN]: Fix egress priority mappings leak.
[TG3]: Add PHY workaround for 5784
[NET]: srandom32 fixes for networking v2
[IPV6]: Fix refcounting for anycast dst entries.
[IPV6]: inet6_dev on loopback should be kept until namespace stop.
[IPV6]: Event type in addrconf_ifdown is mis-used.
[ICMP]: Ensure that ICMP relookup maintains status quo
a) if you initialize something with le32_to_cpu(...), then |= it
with host-endian and feed to cpu_to_le32(), it's most definitely
*not* __le32. As sparse would've told you...
b) the whole sequence is |= cpu_to_le32(host-endian constant)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
My previous section fix only turned one section problem into another
section problem.
This patch fixes it for real.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The other if blocks don't redeclare temp, remove the redeclaration in
the final if() block.
drivers/net/phy/marvell.c:214:7: warning: symbol 'temp' shadows an earlier one
drivers/net/phy/marvell.c:160:6: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 5784 B step and newer chips require the PHY DSPs to be fine-tuned
based on one-time programmable values stored in the chip. This is
essential to achieve optimal PHY operations especially when using
long cables. We also need to properly handle the 10Mbit RX bit in the
CPMU_CTRL register during PHY reset.
Update version to 3.89.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix MPC5200 (not B!) device tree so FEC ethernet works
[POWERPC] mpc5200: Amalgamated DTS fixes and updates
[POWERPC] Fix rtas_flash procfs interface
[POWERPC] Fix deadlock with mmu_hash_lock in hash_page_sync
[POWERPC] Fix iSeries hard irq enabling regression
[POWERPC] Fix CPM2 SCC1 clock initialization.
[POWERPC] Fix defconfigs so we dont set both GENRTC and RTCLIB
[POWERPC] fsldma: Use compatiable binding as spec
[POWERPC] sata_fsl: reduce compatibility to fsl,pq-sata
[POWERPC] 83xx: enable usb in 837x rdb and 83xx defconfigs
[POWERPC] 83xx: Fix wrong USB phy type in mpc837xrdb dts
This gets the FEC ethernet driver working again on the lite5200
platform.
The FEC driver is also compatible with the MPC5200, not only with the
MPC5200B, so this adds a suitable entry to the driver's match list.
Furthermore this adds the settings for the PHY in the dts file for the
Lite5200. Note, that this is not exactly the same as in the
Lite5200B, because the PHY is located at f0003000:01 for the 5200, and
at :00 for the 5200B. This was tested on a Lite5200 and a Lite5200B,
both booted a kernel via tftp and mounted the root via nfs
successfully.
Signed-off-by: René Bürgel <r.buergel@unicontrol.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are a couple of possible races on suspend/resume.
First the driver needs to block new packets from being queued for Tx.
The other less likely problem is the watchdog timer going off
during resume.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits)
[VLAN]: Proc entry is not renamed when vlan device name changes.
[IPV6]: Fix ICMP relookup error path dst leak
[ATM] drivers/atm/iphase.c: compilation warning fix
IPv6: do not create temporary adresses with too short preferred lifetime
IPv6: only update the lifetime of the relevant temporary address
bluetooth : __rfcomm_dlc_close lock fix
bluetooth : use lockdep sub-classes for diffrent bluetooth protocol
[ROSE/AX25] af_rose: rose_release() fix
mac80211: correct use_short_preamble handling
b43: Fix PCMCIA IRQ routing
b43: Add DMA mapping failure messages
mac80211: trigger ieee80211_sta_work after opening interface
[LLC]: skb allocation size for responses
[IP] UDP: Use SEQ_START_TOKEN.
[NET]: Remove Documentation/networking/sk98lin.txt
[ATM] atm/idt77252.c: Make 2 functions static
[ATM]: Make atm/he.c:read_prom_byte() static
[IPV6] MCAST: Ensure to check multicast listener(s).
[LLC]: Kill llc_station_mac_sa symbol export.
forcedeth: fix locking bug with netconsole
...
drivers/net/wireless/ath5k/base.c: In function `ath5k_check_ibss_tsf':
drivers/net/wireless/ath5k/base.c:1740: warning: long long unsigned int format, u64 arg (arg 5)
drivers/net/wireless/ath5k/base.c:1740: warning: long long unsigned int format, u64 arg (arg 6)
drivers/net/wireless/ath5k/base.c:1740: warning: long long int format, u64 arg (arg 7)
drivers/net/wireless/ath5k/base.c:1740: warning: long long unsigned int format, u64 arg (arg 8)
drivers/net/wireless/ath5k/base.c:1757: warning: long long unsigned int format, u64 arg (arg 5)
drivers/net/wireless/ath5k/base.c:1757: warning: long long unsigned int format, u64 arg (arg 6)
drivers/net/wireless/iwlwifi/iwl4965-base.c: In function `iwl4965_tx_status_reply_tx':
drivers/net/wireless/iwlwifi/iwl4965-base.c:3105: warning: long long unsigned int format, u64 arg (arg 6)
drivers/net/wireless/iwlwifi/iwl-4965.c: In function `iwl4965_rx_reply_rx':
drivers/net/wireless/iwlwifi/iwl-4965.c:3978: warning: long long unsigned int format, u64 arg (arg 7)
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement triggers inside rt2x00 itself based
on input from mac80211. This replaces the method
of using the mac80211 trigger events which do
not work for USB drivers due to the scheduling
requirement.
After this patch RT2500USB_LEDS and RT73USB_LEDS
no longer need to be tagged as broken since they
now support LED handling again without having to
check for in_atomic().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TO_DS filter does not only depend on the FIF_PROMISC_IN_BSS flag
provided by mac80211, but also on the intf_ap_count count.
This makes sense, since when Master mode is active, we should all frames
that are send to the active AP (the device itself).
This means that when an interface is added we should force the
packet filter to be updated during the next mac80211 call of
configure_filter() to make sure the intf_ap_count field is checked.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Invert the check for scheduling the packet_filter configuration.
When DRIVER_REQUIRE_SCHEDULED is not set we should immediately
configure the the filter.
This fixes the 'infinite calls to rt2x00mc_configure_filter'
bug reported by Bas Hulsken.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces static variable from send_cmd_sync
with flag in priv->status. It was used for reentrance protection
but clearly made it impossible to stuck more cards into the same machine
In addition it force check of return values of synchronous commands
commands that doesn't requires return value async commands have to be used
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Yi Zhu <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch initialize all fields in led before registering it
This fixes oops on initialization
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an early release of driver's resources before upper stack
was notified that low-level driver shuts down.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having rate registration during module load enables the use of
error checking as well as reliable registration/unregistration
pairing. Previously this was not possible as rate registration
was done during _probe where _probe could be run for more than
one device on the system.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixed the OOPS when load the driver while rf-kill is on then
unload the driver right after load. a race condition caused the interupt
handler to schedule the tasklet which will run right after the driver pci_remove
causing invalid poiter OOPS.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch hook IWL with Linux rfkill.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add notification function to be called by low level
iwl driver to notify iwlcore with current state. This function
will call iwlcore subsystem with the new state. This will
help make the code more consistent and easy to extend. For example
the rf-kill need to know when the driver in init, start, stop or
remove state. Instead doing the same call in 3945 and 4965, we
just do it from this function.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These small changes restore the rt2x00 sources to the way Ivo intended.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Runtime-wise we only need escape_ssid from the deprecated IEEE80211
subsystem. However, it's easy to provide our own copy.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Confirm sleep event: they come very regularly, eventually several times per
second. Therefore we want to send the config command as fast as possible.
The old code pre-set the command in priv->lbs_ps_confirm_sleep. However, the
byte sequence to be sent to the hardware is the same for all interfaces. So
this patch make this an extern structure, initialized at module load time.
Config wake event: normal conversion to a direct command. However, I don't know
how to trigger a "HOST AWAKE" event from the firmware, so this part is
untested.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* directly call lbs_cmd_with_response()
* only overwrite priv->current_addr once the firmware call succeeded
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the IRQ routing on PCMCIA devices.
With this patch the card will finally be able to receive IRQs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds messages for some DMA mapping failures.
These are useful for debugging DMA address problems, as they appear
on x86_64 machines with IOMMU enabled.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Plip uses spin_lock_irq/spin_unlock_irq in its IRQ handler (called from
parport IRQ handler), the latter enables interrupts without parport
subsystem IRQ handler expecting it.
The bug can be seen if you compile kernel with lock dependency checking
and use plip --- it produces a warning.
This patch changes it to spin_lock_irqsave/spin_lock_irqrestore, so that
it doesn't enable interrupts when already disabled.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reorganization moves the PHY status into a separate
struct. Flow Control setup is moved into this struct as well
and frame size away from here into the adapter struct where its
inly use is.
The post-link-up code is now a separate function and moved out
of the watchdog function itself. This allows us to track the
es2lan restart issue a bit easier.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename this function to be consistent with function naming (verb first)
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adjusting the comment blocks here to be code-style compliant. no
code changes.
Changed some copyright dates to 2008.
Indentation fixes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Under CONFIG_DCA the compilation is broken since the commit
bd0362dde0 (ixgbe: Add optional
DCA infrastructure).
IXGBE_SUCCESS is not defined anywhere, replace it with 0.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code is under unused #ifdef NO_TXSTATS branch but its better to have it
fixed.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert the port_lock to a mutex. There is also some additional cleanup. The
line length inside the ehea_rereg_mrs was getting long so I made some
adjustments to shorten them.
[akpm@linux-foundation.org: dec99ification]
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert the ehea_bcmc_regs.lock to a mutex.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Nested locks always need to be taken in the same order. This change factors
out the ehea_fw_handles.lock to make the locking order consistent.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Converted the ehea_fw_handles.lock to a mutex.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Cc: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Converted the dlpar_mem_lock. With a bit of cleanup, I converted to
DEFINE_MUTEX() instead of a runtime init. I also made the lock static.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Acked-by: Jan-Bernd Themann <themann@de.ibm.com>
Cc: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The functions time_before, time_before_eq, time_after, and time_after_eq are
more robust for comparing jiffies against other values.
So use the time_after() macro, defined in linux/jiffies.h, which deals with
wrapping correctly.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: S.Caglar Onur <caglar@pardus.org.tr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The functions time_before, time_before_eq, time_after, and time_after_eq are
more robust for comparing jiffies against other values.
So use the time_after() macro, defined in linux/jiffies.h, which deals with
wrapping correctly.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: S.Caglar Onur <caglar@pardus.org.tr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert 3c509 driver to isa_driver and pnp_driver. The result is that
autoloading using udev and hibernation works with ISA PnP cards. It also adds
hibernation support for non-PnP ISA cards.
xcvr module parameter was removed as its value was not used.
Tested using 3 ISA cards in various combinations of PnP and non-PnP modes.
EISA and MCA only compile-tested.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The asix usb driver currently depends on NET_ETHERNET which means you
cannot enable this driver if you only have 1000mbit enabled in your kernel.
Since there is no real dependency between the NET_ETHERNET portion and the
asix driver, simply drop it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move the "&& skb->ip_summed == CHECKSUM_PARTIAL" part out of
emac_has_feature parameters.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/pasemi_mac.c is enabled by CONFIG_PASEMI_MAC, which depends on
PPC64 && PCI. However pasemi_mac.c uses several routines that are only
built when PPC_PASEMI is selected. This can lead to an unbuildable config:
ERROR: ".pasemi_dma_start_chan" [drivers/net/pasemi_mac.ko] undefined!
So make CONFIG_PASEMI_MAC depend on PPC_PASEMI instead of PPC64.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Updated version number.
- Resubmitting with correct version update.
- this patch to be applied for upstream-davem branch
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove superfluous in-atomic() check; ethtool MII ops are called from task
context.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The loop forgot to walk the net->mc_list list, so only the first
multicast address was programmed into the hash table.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If "location" is > "addr_len" bits, the high bits of location would interfere
with the READ_CMD sent to the eeprom controller.
A patch was submitted to bug:
http://bugzilla.kernel.org/show_bug.cgi?id=4420
which simply truncated the "location", read whatever was in "location
modulo addr_len", and returned that value. That avoids confusing the
eeprom but seems like the wrong solution to me.
Correct would be to not read beyond "1 << addr_len" address of the eeprom.
I am submitting two changes to implement this:
1) tulip_read_eeprom will return zero (since we can't return -EINVAL)
if this is attempted (defensive programming).
2) In tulip_core.c, fix the tulip_read_eeprom caller so they don't
iterate past addr_len bits and make sure the entire tp->eeprom[]
array is cleared.
I konw we don't strictly need both. I would prefer both in the tree
since it documents the issue and provides a second "defense" from
the bug from creeping back in.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
original_mtu is only used if we end up with a non-NULL
dev, and it is assigned in all such cases, but GCC can't
see that.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tries to make dmesg logs between different runs easier
to compare by
* removing the jiffies (use CONFIG_PRINTK_TIME if you need
timing)
* remove the line numbers, they change with each applied patch
It also changes the deprecated __FUNCTION__ to __func__ to make
checkpatch.pl happy.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch alters the A-MPDU MLME in sta_info to use dynamic allocation,
thus drastically improving memory usage - from a constant ~2 Kbyte in
the previous (static) allocation to a lower limit of ~200 Byte and an upper
limit of ~2 Kbyte.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has nowhere been used. Note: in the firmware manual this was
documented as CMD_802_11_PA_CFG. If we ever need it, we can/should
re-implement it as a direct command.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix types of is_open and iw_mode members
of iwl_priv sturct
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch provides a default callback for ASYNC host commands instead
of calling to BUG_ON. Most of the callbacks are now just empty functions
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gives the function's caller name in case NIC
access reference count was not used by it.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl-4965-io.h back to iw-io.h
it also remove 4965 from all functions it supplies
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add LEDS support to 3965 and 4965 drivers. It is based on
led trigger and class. For our drivers we needed to avoid two things.
1- We receive led trigger on/off on each Rx\Tx frame. In our driver
we can not call led command like that. In this driver once driver
receive a start of traffic it call the led command to start blinking
then we count all bytes of Tx and Rx frame, after two second we count the
blink rate of last two second then id blink rate changed we call the led
commands
2- Since we can call led command very often, we make sure we call the
led command after we receive the statistics notification so
we don't need to wake up the ucode id it is in sleep state.
This patch was tested with 4965 and 3945.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Ian Schram<ischram@telenet.be>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware never seem to accept the "goto sleep" command, since the legacy
drivers don't have suspend and resume handlers the entire code for it was
basically a educated guess (based on the "enable radio" code).
This patch will only print a warning when the "goto sleep" command fails, and
just continues as usual. Perhaps that means the device will not reach a sleep
state and consumes more power then it should, but it is equally possible it
simply needs some seconds longer to sleep. Anyway, by making the command
non-fatal it will not block the rest of the suspend procedure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit e6bafba5b4, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Guy Cohen <guy.cohen@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a bug detected by CONFIG_DEBUG_SPINLOCK:
if_cs_get_int_status() is only called from lbs_thread(), via
priv->hw_get_int_status. However, lbs_thread() has already taken the
priv->driver_lock. So it's a fault to take the same lock again here.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Fix Rx/Tx HW interrupt coalescing counter reset logic. Disabling
is required before resetting the counter.
- Update the Default both Rx and Tx coalescing timer
threshold. Formerly 4 is set which is equal to 1.5 frame at the line
rate of 1GbE interface, and it doesn't match to the coalescing frame
count which is set to 16. Threashold 21 is matched to frame count 16.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the LAST bit is not set in the RxBD, it's possible we're processing
an incomplete frame, which is bad. While we're at it, add a constant
for the error bitmask, so the whole if-clause fits on one line,
and is more legible.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In gfar_change_mtu(), the frame size needs to be increased to account
for the extra 4 bytes VLAN adds to the ethernet header. However,
it was being increased by the length of the whole header (18 bytes),
which is wrong.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Buffer stashing parameter change to 96 from 64 in order to cover
the Layer 4 header.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code opening proc entry for each device makes the
same thing, as the single_open does, so remove the
unneeded code.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for BCM5481 PHY. Unfortunately it's hard to
get specifications for this PHY, so its special register 0x18 isn't
annotated properly (but we know it's used to set up the delays).
I've kept the magic numbers, so we'll not forget to fix it at the
first opportunity, and will name that register and its bits correctly.
p.s. also fixed the line with broken indention, introduced by
commit 03157ac31e
PHYLIB: Add BCM5482 PHY support
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert byte order of constant instead of variable which can be done at
compile time (vs run time)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert P.J. Day proposed to use the macro FIELD_SIZEOF in replace of code
that matches its definition.
The modification was made using the following semantic patch
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
type t;
identifier f;
@@
- (sizeof(((t*)0)->f))
+ FIELD_SIZEOF(t, f)
@depends on haskernel@
type t;
identifier f;
@@
- sizeof(((t*)0)->f)
+ FIELD_SIZEOF(t, f)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the IDT rc32434 Ethernet MAC
we can find in the IDT boards and the Mikrotik RB500.
Driver references some code from the linux-mips RB500
support.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Philip Rischel <rischelp@idt.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This timer doesn't need to run at precise times, so round it to a whole
second to decrease wakeups.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
isa_bus_to_virt() is the wrong thing to do here; it happens
to work on i386, but only by accident. What we want is
normal ioremap/readb/etc. set - it's all in iomem.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
take iscp-based testing into helper, kill the loop, stop
wanking with reassignments of priv->iscp
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rusty Russell
Sergei Shtylyov
Krzysztof Halasa
Thomas Klein
Stephen Hemminger
Sonic Zhang
Ayaz Abdulla
Atsushi Nemoto
Joakim Tjernlund
Laurent Pinchart
Stephen Hemminger
Linus Torvalds
Eliezer Tamir
David S. Miller
Daniel Wagner
Christian Lamparter
Johannes Berg
Pavel Machek
Michael Buesch
Mohamed Abbas
Reinette Chatre
Tomas Winkler
Ivo van Doorn
John W. Linville
Holger Schurig
Denys Vlasenko
Luis R. Rodriguez
Abhijeet Kolekar
Daniel Drake
Anthony Liguori
Al Viro
Adrian Bunk
Harvey Harrison
Matt Carlson
René Bürgel
Ron Rindjunsky
Al Viro
Mikulas Patocka
Jeff Kirsher
Bruce Allan
Denis V. Lunev
Mariusz Kozlowski
Daniel Walker
S.Caglar Onur
Ondrej Zary
Ingo Molnar
Mike Frysinger
Mike Frysinger
Valentine Barshak
Michael Ellerman
Sreenivasa Honnur
David Brownell
Peter Korsgaard
Grant Grundler
Robert P. J. Day
Emmanuel Grumbach
Julia Lawall
Andy Fleming
Dai Haruki
Pavel Emelyanov
Anton Vorontsov
Marcin Slusarz
Florian Fainelli