Fix the nm10300 build failure:
In file included from arch/mn10300/kernel/csrc-mn10300.c:14:0:
arch/mn10300/kernel/internal.h:42:1: error: unknown type name 'irqreturn_t'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the warning:
include/linux/ptrace.h:66:0: warning: "PTRACE_O_TRACESYSGOOD" redefined [enabled by default]
arch/mn10300/include/asm/ptrace.h:85:0: note: this is the location of the previous definition
We already have it in <linux/ptrace.h>, so remove it from <asm/ptrace.h>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the static inline function setup_jiffies_interrupt() from
<asm/timex.h> to arch/mn10300/kernel/cevt-mn10300.c, which is its only
callsite.
This allows to remove the inclusion of <asm/hardirq.h> and <linux/irq.h>
from <asm/timex.h> and <unit/timex.h>, fixing include hell like:
include/linux/jiffies.h:260:31: warning: "CLOCK_TICK_RATE" is not defined [-Wundef]
include/linux/jiffies.h:260:31: warning: "CLOCK_TICK_RATE" is not defined [-Wundef]
include/linux/jiffies.h:46:42: error: division by zero in #if
...
make[4]: *** [arch/mn10300/kernel/asm-offsets.s] Error 1
and (after a quick hack for the above by defining CLOCK_TICK_RATE in
<linux/jiffies.h>):
In file included from include/linux/notifier.h:15:0,
from include/linux/memory_hotplug.h:6,
from include/linux/mmzone.h:718,
from include/linux/gfp.h:4,
from include/linux/irq.h:20,
from arch/mn10300/unit-asb2303/include/unit/timex.h:15,
from arch/mn10300/include/asm/timex.h:15,
from include/linux/timex.h:174,
from include/linux/jiffies.h:8,
from include/linux/ktime.h:25,
from include/linux/timer.h:5,
from include/linux/workqueue.h:8,
include/linux/srcu.h:55:22: error: field 'work' has incomplete type
As a consequence, we do need a few more inclusions of <asm/irq.h>, namely
in arch/mn10300/unit-asb2303/smc91111.c and
arch/mn10300/unit-asb2305/unit-init.c.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The declaration of arch_release_thread_info() needs a semicolon.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mn10300 has a header (in its include/asm directory) that is a thin
wrapper around asm-generic/ipc.h. This wrapper is useless, since that
header doesn't exist. It is also unused (no file includes asm/ipc.h).
hexagon and tile generate similar headers at build time (using a
generic-y entry in include/asm/Kbuild). These generated headers are
useless and unused too.
Remove this header and these generic-y entries.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: David Howells <dhowells@redhat.com> [MN10300]
Signed-off-by: Michal Marek <mmarek@suse.cz>
Pull third pile of signal handling patches from Al Viro:
"This time it's mostly helpers and conversions to them; there's a lot
of stuff remaining in the tree, but that'll either go in -rc2
(isolated bug fixes, ideally via arch maintainers' trees) or will sit
there until the next cycle."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
x86: get rid of calling do_notify_resume() when returning to kernel mode
blackfin: check __get_user() return value
whack-a-mole with TIF_FREEZE
FRV: Optimise the system call exit path in entry.S [ver #2]
FRV: Shrink TIF_WORK_MASK [ver #2]
FRV: Prevent syscall exit tracing and notify_resume at end of kernel exceptions
new helper: signal_delivered()
powerpc: get rid of restore_sigmask()
most of set_current_blocked() callers want SIGKILL/SIGSTOP removed from set
set_restore_sigmask() is never called without SIGPENDING (and never should be)
TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set
don't call try_to_freeze() from do_signal()
pull clearing RESTORE_SIGMASK into block_sigmask()
sh64: failure to build sigframe != signal without handler
openrisc: tracehook_signal_handler() is supposed to be called on success
new helper: sigmask_to_save()
new helper: restore_saved_sigmask()
new helpers: {clear,test,test_and_clear}_restore_sigmask()
HAVE_RESTORE_SIGMASK is defined on all architectures now
Pull vfs changes from Al Viro.
"A lot of misc stuff. The obvious groups:
* Miklos' atomic_open series; kills the damn abuse of
->d_revalidate() by NFS, which was the major stumbling block for
all work in that area.
* ripping security_file_mmap() and dealing with deadlocks in the
area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
general.
* ->encode_fh() switched to saner API; insane fake dentry in
mm/cleancache.c gone.
* assorted annotations in fs (endianness, __user)
* parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
* ->update_time() work from Josef.
* other bits and pieces all over the place.
Normally it would've been in two or three pull requests, but
signal.git stuff had eaten a lot of time during this cycle ;-/"
Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
nfs: don't open in ->d_revalidate
vfs: retry last component if opening stale dentry
vfs: nameidata_to_filp(): don't throw away file on error
vfs: nameidata_to_filp(): inline __dentry_open()
vfs: do_dentry_open(): don't put filp
vfs: split __dentry_open()
vfs: do_last() common post lookup
vfs: do_last(): add audit_inode before open
vfs: do_last(): only return EISDIR for O_CREAT
vfs: do_last(): check LOOKUP_DIRECTORY
vfs: do_last(): make ENOENT exit RCU safe
vfs: make follow_link check RCU safe
vfs: do_last(): use inode variable
vfs: do_last(): inline walk_component()
vfs: do_last(): make exit RCU safe
vfs: split do_lookup()
Btrfs: move over to use ->update_time
fs: introduce inode operation ->update_time
reiserfs: get rid of resierfs_sync_super
reiserfs: mark the superblock as dirty a bit later
...
Does block_sigmask() + tracehook_signal_handler(); called when
sigframe has been successfully built. All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).
I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only 3 out of 63 do not. Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
replace boilerplate "should we use ->saved_sigmask or ->blocked?"
with calls of obvious inlined helper...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper. Open-coded instances switched...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull second pile of signal handling patches from Al Viro:
"This one is just task_work_add() series + remaining prereqs for it.
There probably will be another pull request from that tree this
cycle - at least for helpers, to get them out of the way for per-arch
fixes remaining in the tree."
Fix trivial conflict in kernel/irq/manage.c: the merge of Andrew's pile
had brought in commit 97fd75b7b8 ("kernel/irq/manage.c: use the
pr_foo() infrastructure to prefix printks") which changed one of the
pr_err() calls that this merge moves around.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
keys: kill task_struct->replacement_session_keyring
keys: kill the dummy key_replace_session_keyring()
keys: change keyctl_session_to_parent() to use task_work_add()
genirq: reimplement exit_irq_thread() hook via task_work_add()
task_work_add: generic process-context callbacks
avr32: missed _TIF_NOTIFY_RESUME on one of do_notify_resume callers
parisc: need to check NOTIFY_RESUME when exiting from syscall
move key_repace_session_keyring() into tracehook_notify_resume()
TIF_NOTIFY_RESUME is defined on all targets now
Pull KVM changes from Avi Kivity:
"Changes include additional instruction emulation, page-crossing MMIO,
faster dirty logging, preventing the watchdog from killing a stopped
guest, module autoload, a new MSI ABI, and some minor optimizations
and fixes. Outside x86 we have a small s390 and a very large ppc
update.
Regarding the new (for kvm) rebaseless workflow, some of the patches
that were merged before we switch trees had to be rebased, while
others are true pulls. In either case the signoffs should be correct
now."
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
arch/powerpc/kvm/book3s_segment.S and arch/x86/include/asm/kvm_para.h.
I suspect the kvm_para.h resolution ends up doing the "do I have cpuid"
check effectively twice (it was done differently in two different
commits), but better safe than sorry ;)
* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (125 commits)
KVM: make asm-generic/kvm_para.h have an ifdef __KERNEL__ block
KVM: s390: onereg for timer related registers
KVM: s390: epoch difference and TOD programmable field
KVM: s390: KVM_GET/SET_ONEREG for s390
KVM: s390: add capability indicating COW support
KVM: Fix mmu_reload() clash with nested vmx event injection
KVM: MMU: Don't use RCU for lockless shadow walking
KVM: VMX: Optimize %ds, %es reload
KVM: VMX: Fix %ds/%es clobber
KVM: x86 emulator: convert bsf/bsr instructions to emulate_2op_SrcV_nobyte()
KVM: VMX: unlike vmcs on fail path
KVM: PPC: Emulator: clean up SPR reads and writes
KVM: PPC: Emulator: clean up instruction parsing
kvm/powerpc: Add new ioctl to retreive server MMU infos
kvm/book3s: Make kernel emulated H_PUT_TCE available for "PR" KVM
KVM: PPC: bookehv: Fix r8/r13 storing in level exception handler
KVM: PPC: Book3S: Enable IRQs during exit handling
KVM: PPC: Fix PR KVM on POWER7 bare metal
KVM: PPC: Fix stbux emulation
KVM: PPC: bookehv: Use lwz/stw instead of PPC_LL/PPC_STL for 32-bit fields
...
Pull timer updates from Thomas Gleixner.
Various trivial conflict fixups in arch Kconfig due to addition of
unrelated entries nearby. And one slightly more subtle one for sparc32
(new user of GENERIC_CLOCKEVENTS), fixed up as per Thomas.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
timekeeping: Fix a few minor newline issues.
time: remove obsolete declaration
ntp: Fix a stale comment and a few stray newlines.
ntp: Correct TAI offset during leap second
timers: Fixup the Kconfig consolidation fallout
x86: Use generic time config
unicore32: Use generic time config
um: Use generic time config
tile: Use generic time config
sparc: Use: generic time config
sh: Use generic time config
score: Use generic time config
s390: Use generic time config
openrisc: Use generic time config
powerpc: Use generic time config
mn10300: Use generic time config
mips: Use generic time config
microblaze: Use generic time config
m68k: Use generic time config
m32r: Use generic time config
...
Pull first series of signal handling cleanups from Al Viro:
"This is just the first part of the queue (about a half of it);
assorted fixes all over the place in signal handling.
This one ends with all sigsuspend() implementations switched to
generic one (->saved_sigmask-based).
With this, a bunch of assorted old buglets are fixed and most of the
missing bits of NOTIFY_RESUME hookup are in place. Two more fixes sit
in arm and um trees respectively, and there's a couple of broken ones
that need obvious fixes - parisc and avr32 check TIF_NOTIFY_RESUME
only on one of two codepaths; fixes for that will happen in the next
series"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (55 commits)
unicore32: if there's no handler we need to restore sigmask, syscall or no syscall
xtensa: add handling of TIF_NOTIFY_RESUME
microblaze: drop 'oldset' argument of do_notify_resume()
microblaze: handle TIF_NOTIFY_RESUME
score: add handling of NOTIFY_RESUME to do_notify_resume()
m68k: add TIF_NOTIFY_RESUME and handle it.
sparc: kill ancient comment in sparc_sigaction()
h8300: missing checks of __get_user()/__put_user() return values
frv: missing checks of __get_user()/__put_user() return values
cris: missing checks of __get_user()/__put_user() return values
powerpc: missing checks of __get_user()/__put_user() return values
sh: missing checks of __get_user()/__put_user() return values
sparc: missing checks of __get_user()/__put_user() return values
avr32: struct old_sigaction is never used
m32r: struct old_sigaction is never used
xtensa: xtensa_sigaction doesn't exist
alpha: tidy signal delivery up
score: don't open-code force_sigsegv()
cris: don't open-code force_sigsegv()
blackfin: don't open-code force_sigsegv()
...
Pull fpu state cleanups from Ingo Molnar:
"This tree streamlines further aspects of FPU handling by eliminating
the prepare_to_copy() complication and moving that logic to
arch_dup_task_struct().
It also fixes the FPU dumps in threaded core dumps, removes and old
(and now invalid) assumption plus micro-optimizes the exit path by
avoiding an FPU save for dead tasks."
Fixed up trivial add-add conflict in arch/sh/kernel/process.c that came
in because we now do the FPU handling in arch_dup_task_struct() rather
than the legacy (and now gone) prepare_to_copy().
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, fpu: drop the fpu state during thread exit
x86, xsave: remove thread_has_fpu() bug check in __sanitize_i387_state()
coredump: ensure the fpu state is flushed for proper multi-threaded core dump
fork: move the real prepare_to_copy() users to arch_dup_task_struct()
As described in e6fa16ab ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block is
pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate code
across architectures. In the past some architectures got this code wrong,
so using this helper function should stop that from happening again.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
guts of saved_sigmask-based sigsuspend/rt_sigsuspend. Takes
kernel sigset_t *.
Open-coded instances replaced with calling it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull smp hotplug cleanups from Thomas Gleixner:
"This series is merily a cleanup of code copied around in arch/* and
not changing any of the real cpu hotplug horrors yet. I wish I'd had
something more substantial for 3.5, but I underestimated the lurking
horror..."
Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
um: Remove leftover declaration of alloc_task_struct_node()
task_allocator: Use config switches instead of magic defines
sparc: Use common threadinfo allocator
score: Use common threadinfo allocator
sh-use-common-threadinfo-allocator
mn10300: Use common threadinfo allocator
powerpc: Use common threadinfo allocator
mips: Use common threadinfo allocator
hexagon: Use common threadinfo allocator
m32r: Use common threadinfo allocator
frv: Use common threadinfo allocator
cris: Use common threadinfo allocator
x86: Use common threadinfo allocator
c6x: Use common threadinfo allocator
fork: Provide kmemcache based thread_info allocator
tile: Use common threadinfo allocator
fork: Provide weak arch_release_[task_struct|thread_info] functions
fork: Move thread info gfp flags to header
fork: Remove the weak insanity
sh: Remove cpu_idle_wait()
...
Sigh, I missed to check which architecture Kconfig files actually
include the core Kconfig file. There are a few which did not. So we
broke them.
Instead of adding the includes to those, we are better off to move the
include to init/Kconfig like we did already with irqs and others.
This does not change anything for the architectures using the old
style periodic timer mode. It just solves the build wreckage there.
For those architectures which use the clock events infrastructure it
moves the include of the core Kconfig file to "General setup" which is
a way more logical place than having it at random locations specified
by the architecture specific Kconfigs.
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Anna-Maria Gleixner <anna-maria@glx-um.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Historical prepare_to_copy() is mostly a no-op, duplicated for majority of
the architectures and the rest following the x86 model of flushing the extended
register state like fpu there.
Remove it and use the arch_dup_task_struct() instead.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1336692811-30576-1-git-send-email-suresh.b.siddha@intel.com
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The scheduler depends on receiving the CPU_STARTING notification, without
which we end up into a lot of trouble. So add the missing call to
notify_cpu_starting() in the bringup code.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let the core code allocate and handle the kgdb cleanup with the
arch_release_thread_info() function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David Howells <dhowells@redhat.com>
Link: http://lkml.kernel.org/r/20120505150141.996582377@linutronix.de
Same code. Use the generic version. The special Makefile treatment is
pointless anyway as init_task.o contains only data which is handled by
the linker script. So no point on being treated like head text.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Howells <dhowells@redhat.com>
Link: http://lkml.kernel.org/r/20120503085035.011270394@linutronix.de
Preparatory patch to make the idle thread allocation for secondary
cpus generic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20120420124556.964170564@linutronix.de
When a host stops or suspends a VM it will set a flag to show this. The
watchdog will use these functions to determine if a softlockup is real, or the
result of a suspended VM.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
asm-generic changes Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Pull x32 support for x86-64 from Ingo Molnar:
"This tree introduces the X32 binary format and execution mode for x86:
32-bit data space binaries using 64-bit instructions and 64-bit kernel
syscalls.
This allows applications whose working set fits into a 32 bits address
space to make use of 64-bit instructions while using a 32-bit address
space with shorter pointers, more compressed data structures, etc."
Fix up trivial context conflicts in arch/x86/{Kconfig,vdso/vma.c}
* 'x86-x32-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
x32: Fix alignment fail in struct compat_siginfo
x32: Fix stupid ia32/x32 inversion in the siginfo format
x32: Add ptrace for x32
x32: Switch to a 64-bit clock_t
x32: Provide separate is_ia32_task() and is_x32_task() predicates
x86, mtrr: Use explicit sizing and padding for the 64-bit ioctls
x86/x32: Fix the binutils auto-detect
x32: Warn and disable rather than error if binutils too old
x32: Only clear TIF_X32 flag once
x32: Make sure TS_COMPAT is cleared for x32 tasks
fs: Remove missed ->fds_bits from cessation use of fd_set structs internally
fs: Fix close_on_exec pointer in alloc_fdtable
x32: Drop non-__vdso weak symbols from the x32 VDSO
x32: Fix coding style violations in the x32 VDSO code
x32: Add x32 VDSO support
x32: Allow x32 to be configured
x32: If configured, add x32 system calls to system call tables
x32: Handle process creation
x32: Signal-related system calls
x86: Add #ifdef CONFIG_COMPAT to <asm/sys_ia32.h>
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Merge second batch of patches from Andrew Morton:
- various misc things
- core kernel changes to prctl, exit, exec, init, etc.
- kernel/watchdog.c updates
- get_maintainer
- MAINTAINERS
- the backlight driver queue
- core bitops code cleanups
- the led driver queue
- some core prio_tree work
- checkpatch udpates
- largeish crc32 update
- a new poll() feature for the v4l guys
- the rtc driver queue
- fatfs
- ptrace
- signals
- kmod/usermodehelper updates
- coredump
- procfs updates
* emailed from Andrew Morton <akpm@linux-foundation.org>: (141 commits)
seq_file: add seq_set_overflow(), seq_overflow()
proc-ns: use d_set_d_op() API to set dentry ops in proc_ns_instantiate().
procfs: speed up /proc/pid/stat, statm
procfs: add num_to_str() to speed up /proc/stat
proc: speed up /proc/stat handling
fs/proc/kcore.c: make get_sparsemem_vmemmap_info() static
coredump: add VM_NODUMP, MADV_NODUMP, MADV_CLEAR_NODUMP
coredump: remove VM_ALWAYSDUMP flag
kmod: make __request_module() killable
kmod: introduce call_modprobe() helper
usermodehelper: ____call_usermodehelper() doesn't need do_exit()
usermodehelper: kill umh_wait, renumber UMH_* constants
usermodehelper: implement UMH_KILLABLE
usermodehelper: introduce umh_complete(sub_info)
usermodehelper: use UMH_WAIT_PROC consistently
signal: zap_pid_ns_processes: s/SEND_SIG_NOINFO/SEND_SIG_FORCED/
signal: oom_kill_task: use SEND_SIG_FORCED instead of force_sig()
signal: cosmetic, s/from_ancestor_ns/force/ in prepare_signal() paths
signal: give SEND_SIG_FORCED more power to beat SIGNAL_UNKILLABLE
Hexagon: use set_current_blocked() and block_sigmask()
...
ARCH_HAS_NMI_WATCHDOG is a macro defined by arch, but config
HARDLOCKUP_DETECTOR depends on it. This is wrong, ARCH_HAS_NMI_WATCHDOG
has to be a Kconfig config, and arch's need it should select it
explicitly.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
[swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
This is useful for testing RX handling of frames with bad
CRCs.
Requires driver support to actually put the packet on the
wire properly.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Everybody uses the generic pcibios_resource_to_bus() supplied by the core
now, so remove the ARCH_HAS_GENERIC_PCI_OFFSETS used during conversion.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: David Howells <dhowells@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This one specifies where to start MSG_PEEK-ing queue data from. When
set to negative value means that MSG_PEEK works as ususally -- peeks
from the head of the queue always.
When some bytes are peeked from queue and the peeking offset is non
negative it is moved forward so that the next peek will return next
portion of data.
When non-peeking recvmsg occurs and the peeking offset is non negative
is is moved backward so that the next peek will still peek the proper
data (i.e. the one that would have been picked if there were no non
peeking recv in between).
The offset is set using per-proto opteration to let the protocol handle
the locking issues and to check whether the peeking offset feature is
supported by the protocol the socket belongs to.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-next' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: Split trivial #if defined(__KERNEL__) && X conditionals
UAPI: Don't have a #elif clause in a __KERNEL__ guard in linux/soundcard.h
UAPI: Fix AHZ multiple inclusion when __KERNEL__ is removed
UAPI: Make linux/patchkey.h easier to parse
UAPI: Fix nested __KERNEL__ guards in video/edid.h
UAPI: Alter the S390 asm include guards to be recognisable by the UAPI splitter
UAPI: Guard linux/cuda.h
UAPI: Guard linux/pmu.h
UAPI: Guard linux/isdn_divertif.h
UAPI: Guard linux/sound.h
UAPI: Rearrange definition of HZ in asm-generic/param.h
UAPI: Make FRV use asm-generic/param.h
UAPI: Make M32R use asm-generic/param.h
UAPI: Make MN10300 use asm-generic/param.h
UAPI: elf_read_implies_exec() is a kernel-only feature - so hide from userspace
UAPI: Don't include linux/compat.h in sparc's asm/siginfo.h
UAPI: Fix arch/mips/include/asm/Kbuild to have separate header-y lines
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPBZXBAAoJECgfDbjSjVRpuuYIAIMD0wE96MuTOSBJX4VG8VAP
UyjL9dsfMRy8CKioQo5/fxpTY07YBCWmNauSSX7pzgcoUKBfYIGn4Z1qwGYsWK9M
CzLs6PXLTugw0FtKobHZl/klRTWEBS6YOUjp9x568rplwF+Ppk7b993uj7eS/g+e
T0mUKzqg4/UavbHd9+W5KgC4drQ5hgtu2WZHoUxBK4umnd3C2G+U82Sthg50o/XU
SC8IGm39K8I36HoIWgXj3Y7nkOP3mQELohOT4ZPiVSmLvGS4i47+ix75anO+8ZvZ
jxHr8RC85IK1Nd89NZhbKOyvx0QQiwoKUZaTwcWXJNSOADzZnM6icdIsodc+Elo=
=ccQZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
lib: use generic pci_iomap on all architectures
Many architectures don't want to pull in iomap.c,
so they ended up duplicating pci_iomap from that file.
That function isn't trivial, and we are going to modify it
https://lkml.org/lkml/2011/11/14/183
so the duplication hurts.
This reduces the scope of the problem significantly,
by moving pci_iomap to a separate file and
referencing that from all architectures.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
alpha: drop pci_iomap/pci_iounmap from pci-noop.c
mn10300: switch to GENERIC_PCI_IOMAP
mn10300: add missing __iomap markers
frv: switch to GENERIC_PCI_IOMAP
tile: switch to GENERIC_PCI_IOMAP
tile: don't panic on iomap
sparc: switch to GENERIC_PCI_IOMAP
sh: switch to GENERIC_PCI_IOMAP
powerpc: switch to GENERIC_PCI_IOMAP
parisc: switch to GENERIC_PCI_IOMAP
mips: switch to GENERIC_PCI_IOMAP
microblaze: switch to GENERIC_PCI_IOMAP
arm: switch to GENERIC_PCI_IOMAP
alpha: switch to GENERIC_PCI_IOMAP
lib: add GENERIC_PCI_IOMAP
lib: move GENERIC_IOMAP to lib/Kconfig
Fix up trivial conflicts due to changes nearby in arch/{m68k,score}/Kconfig
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups. This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.
CC: David Howells <dhowells@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'latency timer' of PCI devices, both Type 0 and Type 1,
is setup in architecture-specific code [see: 'pcibios_set_master()'].
There are two approaches being taken by all the architectures - check
if the 'latency timer' is currently set between 16 and 255 and if not
bring it within bounds, or, do nothing (and then there is the
gratuitously different PA-RISC implementation).
There is nothing architecture-specific about PCI's 'latency timer' so
this patch pulls its setup functionality up into the PCI core by
creating a generic 'pcibios_set_master()' function using the '__weak'
attribute which can be used by all architectures as a default which,
if necessary, can then be over-ridden by architecture-specific code.
No functional change.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make MN10300 use the generic settings to be found in asm-generic/param.h
rather than defining its own as they're exactly the same.
This sorts out a problem with HZ being redefined after the UAPI split.
Signed-off-by: David Howells <dhowells@redhat.com>
The pci_iomap variant that arch/mn10300/unit-asb2305/pci-iomap.c
uses differs from the generic one in that it does
not use ioremap_nocache for PCI addresses.
However, it turns out that PCI addresses are
automatically noncached, so switching to ioremap_nocache
and to the generic implementation is safe.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The 802.1X EAPOL handshake hostapd does requires
knowing whether the frame was ack'ed by the peer.
Currently, we fudge this pretty badly by not even
transmitting the frame as a normal data frame but
injecting it with radiotap and getting the status
out of radiotap monitor as well. This is rather
complex, confuses users (mon.wlan0 presence) and
doesn't work with all hardware.
To get rid of that hack, introduce a real wifi TX
status option for data frame transmissions.
This works similar to the existing TX timestamping
in that it reflects the SKB back to the socket's
error queue with a SCM_WIFI_STATUS cmsg that has
an int indicating ACK status (0/1).
Since it is possible that at some point we will
want to have TX timestamping and wifi status in a
single errqueue SKB (there's little point in not
doing that), redefine SO_EE_ORIGIN_TIMESTAMPING
to SO_EE_ORIGIN_TXSTATUS which can collect more
than just the timestamp; keep the old constant
as an alias of course. Currently the internal APIs
don't make that possible, but it wouldn't be hard
to split them up in a way that makes it possible.
Thanks to Neil Horman for helping me figure out
the functions that add the control messages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
Awhile back I removed all the CONFIG_GENERIC_TIME referecnes as
the last of the non-GENERIC_TIME arches were converted.
However, due to the functionality being important and around for
awhile, there apparently were some out of tree hardware enablement
patches that used it and have since been merged.
This patch removes the remaining instances of GENERIC_TIME.
Singed-off-by: John Stultz <john.stultz@linaro.org>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After changing all consumers of atomics to include <linux/atomic.h>, we
ran into some compile time errors due to this dependency chain:
linux/atomic.h
-> asm/atomic.h
-> asm-generic/atomic-long.h
where atomic-long.h could use funcs defined later in linux/atomic.h
without a prototype. This patches moves the code that includes
asm-generic/atomic*.h to linux/atomic.h.
Archs that need <asm-generic/atomic64.h> need to select
CONFIG_GENERIC_ATOMIC64 from now on (some of them used to include it
unconditionally).
Compile tested on i386 and x86_64 with allnoconfig.
Signed-off-by: Arun Sharma <asharma@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is in preparation for more generic atomic primitives based on
__atomic_add_unless.
Signed-off-by: Arun Sharma <asharma@fb.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The majority of architectures implement ext2 atomic bitops as
test_and_{set,clear}_bit() without spinlock.
This adds this type of generic implementation in ext2-atomic-setbit.h and
use it wherever possible.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Andreas Dilger <adilger@dilger.ca>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ poleg@redhat.com: no need to declare show_regs() in ptrace.h, sched.h does this ]
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes all the module loader hook implementations in the
architecture specific code where the functionality is the same as that
now provided by the recently added default hooks.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
MN10300's asm/uaccess.h needs to #include linux/kernel.h to get might_sleep()
otherwise it fails to build on MN10300 allyesconfig. This fails in a few
places with messages like the following:
In file included from security/keys/trusted.c:14:
include/linux/uaccess.h: In function '__copy_from_user_nocache':
include/linux/uaccess.h:52: error: implicit declaration of function 'might_sleep'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
_sdata needs to be declared in the linker script now as of commit
a2d063ac21 ("extable, core_kernel_data(): Make sure all archs define
_sdata")
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
die_if_no_fixup() shouldn't use get_user() as it doesn't call set_fs() to
indicate that it wants to probe a kernel address. Instead it should use
probe_kernel_read().
This fixes the problem of gdb seeing SIGILL rather than SIGTRAP when hitting
the KGDB special breakpoint upon SysRq+g being seen. The problem was that
die_if_no_fixup() was failing to read the opcode of the instruction that caused
the exception, and thus not fixing up the exception.
This caused gdb to get a S04 response to the $? request in its remote protocol
rather than S05 - which would then cause it to continue with $C04 rather than
$c in an attempt to pass the signal onto the inferior process. The kernel,
however, does not support $Cnn, and so objects by returning an E22 response,
indicating an error. gdb does not expect this and prints:
warning: Remote failure reply: E22
and then returns to the gdb command prompt unable to continue.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the kernel debugger cacheflush variants escaped proper testing. Two of
the labels are wrong, being derived from the code that was copied to construct
the variant.
The first label results in the following assembler message:
AS arch/mn10300/mm/cache-dbg-flush-by-reg.o
arch/mn10300/mm/cache-dbg-flush-by-reg.S: Assembler messages:
arch/mn10300/mm/cache-dbg-flush-by-reg.S:123: Error: symbol `debugger_local_cache_flushinv_no_dcache' is already defined
And the second label results in the following linker message:
arch/mn10300/mm/built-in.o:(.text+0x1d39): undefined reference to `mn10300_local_icache_inv_range_reg_end'
arch/mn10300/mm/built-in.o:(.text+0x1d39): relocation truncated to fit: R_MN10300_PCREL16 against undefined symbol `mn10300_local_icache_inv_range_reg_end'
To test this file the following configuration pieces must be set:
CONFIG_AM34=y
CONFIG_MN10300_CACHE_WBACK=y
CONFIG_MN10300_DEBUGGER_CACHE_FLUSH_BY_REG=y
CONFIG_MN10300_CACHE_MANAGE_BY_REG=y
CONFIG_AM34_HAS_CACHE_SNOOP=n
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
32bit and 64bit on x86 are tested and working. The rest I have looked
at closely and I can't find any problems.
setns is an easy system call to wire up. It just takes two ints so I
don't expect any weird architecture porting problems.
While doing this I have noticed that we have some architectures that are
very slow to get new system calls. cris seems to be the slowest where
the last system calls wired up were preadv and pwritev. avr32 is weird
in that recvmmsg was wired up but never declared in unistd.h. frv is
behind with perf_event_open being the last syscall wired up. On h8300
the last system call wired up was epoll_wait. On m32r the last system
call wired up was fallocate. mn10300 has recvmmsg as the last system
call wired up. The rest seem to at least have syncfs wired up which was
new in the 2.6.39.
v2: Most of the architecture support added by Daniel Lezcano <dlezcano@fr.ibm.com>
v3: ported to v2.6.36-rc4 by: Eric W. Biederman <ebiederm@xmission.com>
v4: Moved wiring up of the system call to another patch
v5: ported to v2.6.39-rc6
v6: rebased onto parisc-next and net-next to avoid syscall conflicts.
v7: ported to Linus's latest post 2.6.39 tree.
> arch/blackfin/include/asm/unistd.h | 3 ++-
> arch/blackfin/mach-common/entry.S | 1 +
Acked-by: Mike Frysinger <vapier@gentoo.org>
Oh - ia64 wiring looks good.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By the previous style change, CONFIG_GENERIC_FIND_NEXT_BIT,
CONFIG_GENERIC_FIND_BIT_LE, and CONFIG_GENERIC_FIND_LAST_BIT are not used
to test for existence of find bitops anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ns_cgroup is an annoying cgroup at the namespace / cgroup frontier and
leads to some problems:
* cgroup creation is out-of-control
* cgroup name can conflict when pids are looping
* it is not possible to have a single process handling a lot of
namespaces without falling in a exponential creation time
* we may want to create a namespace without creating a cgroup
The ns_cgroup was replaced by a compatibility flag 'clone_children',
where a newly created cgroup will copy the parent cgroup values.
The userspace has to manually create a cgroup and add a task to
the 'tasks' file.
This patch removes the ns_cgroup as suggested in the following thread:
https://lists.linux-foundation.org/pipermail/containers/2009-June/018616.html
The 'cgroup_clone' function is removed because it is no longer used.
This is a userspace-visible change. Commit 45531757b4 ("cgroup: notify
ns_cgroup deprecated") (merged into 2.6.27) caused the kernel to emit a
printk warning users that the feature is planned for removal. Since that
time we have heard from XXX users who were affected by this.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adapt to the new API.
We plan to remove old cpumask APIs later. Thus this patch converts them
into the new one.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fold all the mmu_gather rework patches into one for submission
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Unify input section names
percpu: Avoid extra NOP in percpu_cmpxchg16b_double
percpu: Cast away printk format warning
percpu: Always align percpu output section to PAGE_SIZE
Fix up fairly trivial conflict in arch/x86/include/asm/percpu.h as per Tejun
For future rework of try_to_wake_up() we'd like to push part of that
function onto the CPU the task is actually going to run on.
In order to do so we need a generic callback from the existing scheduler IPI.
This patch introduces such a generic callback: scheduler_ipi() and
implements it as a NOP.
BenH notes: PowerPC might use this IPI on offline CPUs under rare conditions!
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110405152728.744338123@chello.nl
Percpu allocator honors alignment request upto PAGE_SIZE and both the
percpu addresses in the percpu address space and the translated kernel
addresses should be aligned accordingly. The calculation of the
former depends on the alignment of percpu output section in the kernel
image.
The linker script macros PERCPU_VADDR() and PERCPU() are used to
define this output section and the latter takes @align parameter.
Several architectures are using @align smaller than PAGE_SIZE breaking
percpu memory alignment.
This patch removes @align parameter from PERCPU(), renames it to
PERCPU_SECTION() and makes it always align to PAGE_SIZE. While at it,
add PCPU_SETUP_BUG_ON() checks such that alignment problems are
reliably detected and remove percpu alignment comment recently added
in workqueue.c as the condition would trigger BUG way before reaching
there.
For um, this patch raises the alignment of percpu area. As the area
is in .init, there shouldn't be any noticeable difference.
This problem was discovered by David Howells while debugging boot
failure on mn10300.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: user-mode-linux-devel@lists.sourceforge.net
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
MN10300: gcc 4.6 vs am33 inline assembly
MN10300: Deprecate gdbstub
MN10300: Allow KGDB to use the MN10300 serial ports
MN10300: Emulate single stepping in KGDB on MN10300
MN10300: Generalise kernel debugger kernel halt, reboot or power off hook
KGDB: Notify GDB of machine halt, reboot or power off
MN10300: Use KGDB
MN10300: Create generic kernel debugger hooks
MN10300: Create general kernel debugger cache flushing
MN10300: Introduce a general config option for kernel debugger hooks
MN10300: The icache invalidate functions should disable the icache first
MN10300: gdbstub: Restrict single-stepping to non-preemptable non-SMP configs
minix bit operations are only used by minix filesystem and useless by
other modules. Because byte order of inode and block bitmaps is different
on each architecture like below:
m68k:
big-endian 16bit indexed bitmaps
h8300, microblaze, s390, sparc, m68knommu:
big-endian 32 or 64bit indexed bitmaps
m32r, mips, sh, xtensa:
big-endian 32 or 64bit indexed bitmaps for big-endian mode
little-endian bitmaps for little-endian mode
Others:
little-endian bitmaps
In order to move minix bit operations from asm/bitops.h to architecture
independent code in minix filesystem, this provides two config options.
CONFIG_MINIX_FS_BIG_ENDIAN_16BIT_INDEXED is only selected by m68k.
CONFIG_MINIX_FS_NATIVE_ENDIAN is selected by the architectures which use
native byte order bitmaps (h8300, microblaze, s390, sparc, m68knommu,
m32r, mips, sh, xtensa). The architectures which always use little-endian
bitmaps do not select these options.
Finally, we can remove minix bit operations from asm/bitops.h for all
architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the result of conversions, there are no users of ext2 non-atomic bit
operations except for ext2 filesystem itself. Now we can put them into
architecture independent code in ext2 filesystem, and remove from
asm/bitops.h for all architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce little-endian bit operations to the big-endian architectures
which do not have native little-endian bit operations and the
little-endian architectures. (alpha, avr32, blackfin, cris, frv, h8300,
ia64, m32r, mips, mn10300, parisc, sh, sparc, tile, x86, xtensa)
These architectures can just include generic implementation
(asm-generic/bitops/le.h).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GCC 4.6 explicitly represents the MDR register. It may be accessed
via the "z" constraint. Perhaps more importantly, it tracks when
the MDR register is clobbered and uses the RETF instruction if the
incoming value is still valid.
Thus it is important to (at least) clobber the MDR register in
relevant inline assembly fragments, lest RETF be used incorrectly.
The only instances I could find are here. There are reads of the
MDR register in kernel/gdb-stub.c, but that's harmless. Although,
frankly, __builtin_return_address(0) might be a better thing in
those cases. Certainly MDR isn't going to contain anything else
that might be useful...
Signed-off-by: Richard Henderson <rth@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
All architectures can use the common dma_addr_t typedef now. We can
remove the arch specific dma_addr_t.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a node parameter to alloc_thread_info(), and change its name to
alloc_thread_info_node()
This change is needed to allow NUMA aware kthread_create_on_cpu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Deprecate the MN10300 arch's gdbstub in favour of KGDB, which is more capable
in some areas (such as SMP) and almost as capable in others (it's I/O is not as
decoupled and it can't start as early). gdbstub will be removed in a later
version when we're satisfied with KGDB's working.
Signed-off-by: David Howells <dhowells@redhat.com>
Allow KGDB to use the MN10300 serial ports through the polled I/O interface
provided via the TTY/serial layer and the kgdboc driver. This allows the
kernel to be started with something like:
kgdboc=ttySM0,115200
added to the command line.
Signed-off-by: David Howells <dhowells@redhat.com>
Emulate single stepping in KGDB on MN10300 by way of temporary breakpoint
insertion. These breakpoints are never actually seen by KGDB, and will overlay
KGDB's own breakpoints.
The breakpoints are removed by switch_to() and reinstalled on switching back so
that if preemption occurs, the preempting task doesn't hit them (though it will
still hit KGDB's regular breakpoints). If KGDB is reentered for any reason,
then the single step breakpoint is completely erased and must be set again by
the debugger.
We take advantage of the fact that KGDB will effectively halt all other CPUs
whilst this CPU is single-stepping to avoid SMP problems.
If the single-stepping task is preempted and killed without KGDB being
reinvoked, then the breakpoint(s) will be cleared and KGDB will be jumped back
into.
Signed-off-by: David Howells <dhowells@redhat.com>
Generalise the kernel debugger hook for notification of halt, reboot or power
off. This is used by gdbstub to tell the debugger it is exiting. This will be
useful for KGDB too.
Signed-off-by: David Howells <dhowells@redhat.com>
Create generic kernel debugger hooks in the MN10300 arch and make gdbstub use
them. This is a preparation for KGDB support.
Signed-off-by: David Howells <dhowells@redhat.com>
Create general kernel debugger cache flushing for MN10300 and get rid of the
old stuff that gdbstub was using.
Signed-off-by: David Howells <dhowells@redhat.com>
Introduce a general config option for kernel debugger hooks so that both
gdbstub and kgdb can use it and add a header file for both debuggers to use.
Signed-off-by: David Howells <dhowells@redhat.com>
The icache invalidate functions should disable the icache on AM33 and wait for
it to quiesce before attempting to invalidate it, and should then wait for it
to quiesce again before reenabling it, but on AM34 they should invalidate
directly. The same goes for the dcache invalidation, but this isn't used much.
Whilst we're at it, this can be wrapped in assembler macros to remove duplicate
code.
The AM33 manual states that:
An operation that invalidates the cache, switches the writing mode, or
changes the way mode must be performed after disabling the cache,
checking the busy bit, and confirming that the cache is not in
operation.
for the dcache [sec 2.8.3.2.1]. This is not stated so for the icache [sec
2.8.3.1.1] but the example code there suggests that it is.
Whilst the AM34 manual states that the cache must be disabled for both the
icache [sec 1.8.3.2.1] and the dcache [sec 1.8.3.2.1], the Panasonic hardware
engineers say the manual is wrong and that disabling the caches for
invalidation is wrong.
Furthermore, they say that disabling the caches on the AM34 whilst running an
SMP kernel can lead to incoherency between the various CPU caches and should
thus be avoided.
Signed-off-by: David Howells <dhowells@redhat.com>
Restrict single-stepping through the kernel using gdbstub to non-preemptable
non-SMP configs as gdbstub has to do software single-stepping by means of
temporary breakpoints. Hardware single-stepping is unavailable as Panasonic
have not sufficiently documented the interface to it.
Software single-stepping through preemptable or SMP kernels runs into problems
as it makes it much more likely that the wrong thread will hit the temporary
breakpoints. It seems impractical to work around the problem for the most
part. It could be possible to make a UP preemptable kernel switch temporary
breakpoints in and out in switch_to().
Signed-off-by: David Howells <dhowells@redhat.com>
Clear the interrupt mask registers of ASB2364 peripherals before enabling
interrupts so that any peripherals that weren't dealt with by the bootloader
after a reboot (if there was one) won't cause an interrupt storm when
interrupts are first enabled before the drivers are initialised.
Also, attempt to reset the peripherals attached to the FPGA.
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the ASB2364 gdbport UART register definitions. These registers are
actually 2 bytes apart, not 4 (which the ASB2303 and ASB2305 are).
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the definition of the ASB2364 FPGA IRQ detect registers. They accidentally
got defined to be the same as the mask registers when the patches were being
ported to the upstream kernel.
Signed-off-by: David Howells <dhowells@redhat.com>
Select HAVE_GENERIC_HARDIRQS rather than GENERIC_HARDIRQS in MN10300's main
Kconfig file to avoid this warning:
warning: (MN10300) selects GENERIC_HARDIRQS which has unmet direct dependencies (HAVE_GENERIC_HARDIRQS)
Signed-off-by: David Howells <dhowells@redhat.com>
irq_chip.end is obsolete with the removal of __do_IRQ().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Use clockevents_calc_mult_shift() instead of the homebrewn function in
mn10300/kernel/time.c.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
clocksource_register_hz() calculates the shift/mult pair for the
clocksource. Remove the mn10300 duplicate implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
mn10300 implements clocksource and clockevents and selects them
unconditionally in Kconfig. Remove the stale code which seems to be a
leftover of the conversion. Cleanup the configuration switches as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
* 'for-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu, x86: Add arch-specific this_cpu_cmpxchg_double() support
percpu: Generic support for this_cpu_cmpxchg_double()
alpha: use L1_CACHE_BYTES for cacheline size in the linker script
percpu: align percpu readmostly subsection to cacheline
Fix up trivial conflict in arch/x86/kernel/vmlinux.lds.S due to the
percpu alignment having changed ("x86: Reduce back the alignment of the
per-CPU data section")
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (62 commits)
posix-clocks: Check write permissions in posix syscalls
hrtimer: Remove empty hrtimer_init_hres_timer()
hrtimer: Update hrtimer->state documentation
hrtimer: Update base[CLOCK_BOOTTIME].offset correctly
timers: Export CLOCK_BOOTTIME via the posix timers interface
timers: Add CLOCK_BOOTTIME hrtimer base
time: Extend get_xtime_and_monotonic_offset() to also return sleep
time: Introduce get_monotonic_boottime and ktime_get_boottime
hrtimers: extend hrtimer base code to handle more then 2 clockids
ntp: Remove redundant and incorrect parameter check
mn10300: Switch do_timer() to xtimer_update()
posix clocks: Introduce dynamic clocks
posix-timers: Cleanup namespace
posix-timers: Add support for fd based clocks
x86: Add clock_adjtime for x86
posix-timers: Introduce a syscall for clock tuning.
time: Splitout compat timex accessors
ntp: Add ADJ_SETOFFSET mode bit
time: Introduce timekeeping_inject_offset
posix-timer: Update comment
...
Fix up new system-call-related conflicts in
arch/x86/ia32/ia32entry.S
arch/x86/include/asm/unistd_32.h
arch/x86/include/asm/unistd_64.h
arch/x86/kernel/syscall_table_32.S
(name_to_handle_at()/open_by_handle_at() vs clock_adjtime()), and some
due to movement of get_jiffies_64() in:
kernel/time.c
atomic_read() needs to ensure that it emits a load (which it can do by using
ACCESS_ONCE()).
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: David Howells <dhowells@redhat.com>
The invalidate-only versions of flush_icache_*range() are trying sending the
SMP_ICACHE_INV_FLUSH_RANGE IPI command in SMP kernels when they should be
sending SMP_ICACHE_INV_RANGE as the former does not exist.
Signed-off-by: David Howells <dhowells@redhat.com>
Using __get_user_check(x, ptr++, size) leads to double increment of pointer.
This macro uses the macro get_user directly, which itself is used in this way
(get_user(x, ptr++)) in some functions of the kernel. The patch fixes the
error.
Reported-by: Tkhai Kirill <tkhai@yandex.ru>
Signed-off-by: David Howells <dhowells@redhat.com>
Only one CPU gets the timer interrupt so mn10300_last_tsc does not
need to be protected by xtime lock. Remove xtime lovking and use
xtime_update() which does the locking itself.
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
LKML-Reference: <20110127150011.23248.62040.stgit@localhost>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently percpu readmostly subsection may share cachelines with other
percpu subsections which may result in unnecessary cacheline bounce
and performance degradation.
This patch adds @cacheline parameter to PERCPU() and PERCPU_VADDR()
linker macros, makes each arch linker scripts specify its cacheline
size and use it to align percpu subsections.
This is based on Shaohua's x86 only patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shaohua Li <shaohua.li@intel.com>
All architectures are finally converted. Remove the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For arch which needs USE_GENERIC_SMP_HELPERS, it has to select
USE_GENERIC_SMP_HELPERS, rather than leaving a choice to user, since they
don't provide their own implementions.
Also, move on_each_cpu() to kernel/smp.c, it is strange to put it in
kernel/softirq.c.
For arch which doesn't use USE_GENERIC_SMP_HELPERS, e.g. blackfin, only
on_each_cpu() is compiled.
Signed-off-by: Amerigo Wang <amwang@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Occasionally the system gets into a state where the CMOS clock has gotten
slightly ahead of current time and the periodic update of RTC fails. The
message is a nuisance and repeats spamming the log.
See: http://www.ntp.org/ntpfaq/NTP-s-trbl-spec.htm#Q-LINUX-SET-RTC-MMSS
Rather than just removing the message, make it show only once and reduce
severity since it indicates a normal and non urgent condition.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The cnt32_to_63 algorithm relies on proper counter data evaluation
ordering to work properly. This was missing from the provided
documentation.
Let's augment the documentation with the missing usage constraint and
fix the only instance that got it wrong.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the name of interrupt mask alteration function (ie the
local_change_intr_mask_level() fn) called in gdbstub to have an arch_
prefix to match the definition in asm/irqflags.h.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement asm/syscall.h for the MN10300 arch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (38 commits)
kbuild: convert `arch/tile' to the kconfig mainmenu upgrade
README: cite nconfig
Revert "kconfig: Temporarily disable dependency warnings"
kconfig: Use PATH_MAX instead of 128 for path buffer sizes.
kconfig: Fix realloc usage()
kconfig: Propagate const
kconfig: Don't go out from read config loop when you read new symbol
kconfig: fix menuconfig on debian lenny
kbuild: migrate all arch to the kconfig mainmenu upgrade
kconfig: expand file names
kconfig: use the file's name of sourced file
kconfig: constify file name
kconfig: don't emit warning upon rootmenu's prompt redefinition
kconfig: replace KERNELVERSION usage by the mainmenu's prompt
kconfig: delay gconf window initialization
kconfig: expand by default the rootmenu's prompt
kconfig: add a symbol string expansion helper
kconfig: regen parser
kconfig: implement the `mainmenu' directive
kconfig: allow PACKAGE to be defined on the compiler's command-line
...
Fix up trivial conflict in arch/mn10300/Kconfig
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300: (44 commits)
MN10300: Save frame pointer in thread_info struct rather than global var
MN10300: Change "Matsushita" to "Panasonic".
MN10300: Create a defconfig for the ASB2364 board
MN10300: Update the ASB2303 defconfig
MN10300: ASB2364: Add support for SMSC911X and SMC911X
MN10300: ASB2364: Handle the IRQ multiplexer in the FPGA
MN10300: Generic time support
MN10300: Specify an ELF HWCAP flag for MN10300 Atomic Operations Unit support
MN10300: Map userspace atomic op regs as a vmalloc page
MN10300: And Panasonic AM34 subarch and implement SMP
MN10300: Delete idle_timestamp from irq_cpustat_t
MN10300: Make various interrupt priority settings configurable
MN10300: Optimise do_csum()
MN10300: Implement atomic ops using atomic ops unit
MN10300: Make the FPU operate in non-lazy mode under SMP
MN10300: SMP TLB flushing
MN10300: Use the [ID]PTEL2 registers rather than [ID]PTEL for TLB control
MN10300: Make the use of PIDR to mark TLB entries controllable
MN10300: Rename __flush_tlb*() to local_flush_tlb*()
MN10300: AM34 erratum requires MMUCTR read and write on exception entry
...
Use new 'datap' variable in order to remove unnecessary castings.
Also remove checking @addr less than 0 because @addr is now unsigned.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the arguments to arch_ptrace() to take account of the fact that
@addr and @data are now unsigned long rather than long as of a preceding
patch in this series.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christoph reported a nice splat which illustrated a race in the new stack
based kmap_atomic implementation.
The problem is that we pop our stack slot before we're completely done
resetting its state -- in particular clearing the PTE (sometimes that's
CONFIG_DEBUG_HIGHMEM). If an interrupt happens before we actually clear
the PTE used for the last slot, that interrupt can reuse the slot in a
dirty state, which triggers a BUG in kmap_atomic().
Fix this by introducing kmap_atomic_idx() which reports the current slot
index without actually releasing it and use that to find the PTE and delay
the _pop() until after we're completely done.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Christoph Hellwig <hch@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Save the current exception frame pointer in the thread_info struct rather than
in a global variable as the latter makes SMP tricky, especially when preemption
is also enabled.
This also replaces __frame with current_frame() and rearranges header file
inclusions to make it all compile.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Create a defconfig for the ASB2364 board.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Add support for SMSC911X and SMC911X for the ASB2364 unit.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: steve.glendinning@smsc.com
cc: netdev@vger.kernel.org
Use an ELF HWCAP flag to indicate to the process that the CPU provides LL/SC
equivalent atomic operations unit support in addition to BSET/BCLR.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The AM34 processor has an atomic operation that's the equivalent of LL/SC on
other architectures. However, rather than being done through a pair of
instructions, it's driven by writing to a pair of memory-mapped CPU control
registers.
One set of these registers (AARU/ADRU/ASRU) is available for use by userspace,
but for userspace to access them a PTE must be set up to cover the region.
This is done by dedicating the first vmalloc region page to this purpose,
setting the permissions on its PTE such that userspace can access the page.
glibc is hardcoded to expect the registers to be there.
The way atomic ops are done through these registers is straightforward:
(1) Write the address of the word you wish to access into AARU. This causes
the CPU to go and fetch that word and load it into ADRU. The status bits
are also cleared in ASRU.
(2) The current data value is read from the ADRU register and modified.
(3) To alter the data in RAM, the revised data is written back to the ADRU
register, which causes the CPU to attempt to write it back.
(4) The ASRU.RW flag (ASRU read watch), ASRU.LW flag (bus lock watch),
ASRU.IW (interrupt watch) and the ASRU.BW (bus error watch) flags then
must be checked to confirm that the operation wasn't aborted. If any of
the watches have been set to true, the operation was aborted.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Implement the Panasonic MN10300 AM34 CPU subarch and implement SMP support for
MN10300. Also implement support for the MN2WS0060 processor and the ASB2364
evaluation board which are AM34 based.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Make the settings of interrupt priorities used by various services configurable
at run time.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Optimise do_csum() to gang up the loads so they're less likely to get
interruptions between.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Implement atomic ops using the atomic ops unit available in the AM34 CPU. This
allows the equivalent of the LL/SC instructions to be found on other CPUs.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Make the FPU operate in non-lazy mode under SMP so that when the process that
is currently using the FPU migrates to a different CPU, we don't have to ping
its previous CPU to flush the FPU context.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Implement global TLB flushing for MN10300. This will be used by the AM34 which
is SMP capable.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Use the [ID]PTEL2 registers rather than [ID]PTEL for TLB control as the bits
are a more suitable layout.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Make controllable the use of the PIDR register to mark TLB entries as belonging
to particular processes.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Rename __flush_tlb*() to local_flush_tlb*() as it's more appropriate, and ready
to differentiate local from global TLB flushes when SMP is introduced.
Whilst we're at it, get rid of __flush_tlb_global() and make
local_flush_tlb_page() take an mm_struct pointer rather than VMA pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
An AM34 erratum requires MMUCTR read and write on entry to certain exceptions,
prior to EPSW.NMID being cleared to allow NMIs to happen.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Make the boot wrapper able to use writeback caching, including flushing the
cache before jumping to the main kernel.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Implement SMP global cache flushing for MN10300. This will be used by the AM34
which is SMP capable.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The AM34 CPU core provides an automated way of purging the cache rather than
manually iterating over all the tags in the cache. Make it possible to use
these.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Differentiate local cache flushing from global cache flushing so that they can
be done differently on SMP systems.
Rename the cache functions from:
mn10300_[id]cache_*()
to:
mn10300_[id]_localcache_*()
and on a UP system, assign the global labels to the local labels.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The functions that perform cache flushing should take addresses of unsigned
long type, not unsigned int.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The current cache flush and invalidate routines operate by controlling the
cache tag registers. Rename the files and add config items to select them.
This makes it easier to support the use of other cache flush methods instead,
such as the use of AM34's area purge registers, if available.
Signed-off-by: David Howells <dhowells@redhat.com>
Reorder asm/cacheflush.h to put arch primitives first, before the main
functions so that the main functions can be inline asm rather than #defines
when non-trivial.
Signed-off-by: David Howells <dhowells@redhat.com>
Provide a MN10300_CACHE_ENABLED config option as inverted logic of
MN10300_CACHE_DISABLED to make things simpler.
Signed-off-by: David Howells <dhowells@redhat.com>
Remove the monitor trap function and the set_jtag_stub function as they're not
really necessary.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Add CPU register declarations for the AM34 subarch.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Don't hard code the cacheline size in the cache control register definitions.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Move the DMA engine control register definitions to the MN103E010 processor
directory so that the MN2WS0050 processor can have its own.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Differentiate AM33_2 and AM33_3 CPU cores in configuration. The MN103E010
processor contains an AM33_2 core.
Whilst we're at it, prepare for AM34-based stuff by declaring AM34_2 too.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The local_irq_disable() function and co. merely raise the interrupt mask on the
MN10300 arch to exclude normal interrupts. This still lets other, higher
priority maskable interrupts through, such as are used to service gdbstub's
serial port and the MN10300 on-chip serial port virtual FIFOs.
Provide functions to allow the maskable interrupts to be fully disabled, which
will exclude those interrupts.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Don't cast away the volatile in test_bit()'s parameter when we change its type
from const volatile void * so that we can dereference it.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Prevent cnt32_to_63() from being preempted in sched_clock() because it may
read its internal counter, get preempted, get delayed for more than the half
period of the 'TSC' and then write the internal counter, thus corrupting it.
Whilst some callers of sched_clock() have interrupts disabled or hold
spinlocks, not all do, and so preemption must be held here.
Note that sched_clock() is called from lockdep, but that shouldn't be a problem
because although preempt_disable() calls into lockdep, lockdep has a recursion
counter to deal with this.
Signed-off-by: David Howells <dhowells@redhat.com>
Instead of open-coding pci_find_parent_resource and request_resource,
just call pci_claim_resource.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Change the index to unsigned long in all bitops for [mn10300]
Signed-off-by: Justin Chen <justin.chen@hp.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Since we no longer need to provide KM_type, the whole pte_*map_nested()
API is now redundant, remove it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keep the current interface but ignore the KM_type and use a stack based
approach.
The advantage is that we get rid of crappy code like:
#define __KM_PTE \
(in_nmi() ? KM_NMI_PTE : \
in_irq() ? KM_IRQ_PTE : \
KM_PTE0)
and in general can stop worrying about what context we're in and what kmap
slots might be appropriate for that.
The downside is that FRV kmap_atomic() gets more expensive.
For now we use a CPP trick suggested by Andrew:
#define kmap_atomic(page, args...) __kmap_atomic(page)
to avoid having to touch all kmap_atomic() users in a single patch.
[ not compiled on:
- mn10300: the arch doesn't actually build with highmem to begin with ]
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix up drivers/gpu/drm/i915/intel_overlay.c]
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the MN10300 arch, we occasionally see an assertion being tripped in
alloc_cwqs() at the following line:
/* just in case, make sure it's actually aligned */
---> BUG_ON(!IS_ALIGNED(wq->cpu_wq.v, align));
return wq->cpu_wq.v ? 0 : -ENOMEM;
The values are:
wa->cpu_wq.v => 0x902776e0
align => 0x100
and align is calculated by the following:
const size_t align = max_t(size_t, 1 << WORK_STRUCT_FLAG_BITS,
__alignof__(unsigned long long));
This is because the pointer in question (wq->cpu_wq.v) loses some of its
lower bits to control flags, and so the object it points to must be
sufficiently aligned to avoid the need to use those bits for pointing to
things.
Currently, 4 control bits and 4 colour bits are used in normal
circumstances, plus a debugging bit if debugging is set. This requires
the cpu_workqueue_struct struct to be at least 256 bytes aligned (or 512
bytes aligned with debugging).
PERCPU() alignment on MN13000, however, is only 32 bytes as set in
vmlinux.lds.S. So we set this to PAGE_SIZE (4096) to match most other
arches and stick a comment in alloc_cwqs() for anyone else who triggers
the assertion.
Reported-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (49 commits)
serial8250: ratelimit "too much work" error
serial: bfin_sport_uart: speed up sport RX sample rate to be 3% faster
serial: abstraction for 8250 legacy ports
serial/imx: check that the buffer is non-empty before sending it out
serial: mfd: add more baud rates support
jsm: Remove the uart port on errors
Alchemy: Add UART PM methods.
8250: allow platforms to override PM hook.
altera_uart: Don't use plain integer as NULL pointer
altera_uart: Fix missing prototype for registering an early console
altera_uart: Fixup type usage of port flags
altera_uart: Make it possible to use Altera UART and 8250 ports together
altera_uart: Add support for different address strides
altera_uart: Add support for getting mapbase and IRQ from resources
altera_uart: Add support for polling mode (IRQ-less)
serial: Factor out uart_poll_timeout() from 8250 driver
serial: mark the 8250 driver as maintained
serial: 8250: Don't delay after transmitter is ready.
tty: MAINTAINERS: add drivers/serial/jsm/ as maintained driver
vcs: invoke the vt update callback when /dev/vcs* is written to
...
This patch converts mn10300 to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- The generic version provides TIOCGRS485 and TIOCSRS485 but they
are unused by any driver available for this architecture.
- The generic version adds support for termiox
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the IRQ flag handling naming. In linux/irqflags.h under one configuration,
it maps:
local_irq_enable() -> raw_local_irq_enable()
local_irq_disable() -> raw_local_irq_disable()
local_irq_save() -> raw_local_irq_save()
...
and under the other configuration, it maps:
raw_local_irq_enable() -> local_irq_enable()
raw_local_irq_disable() -> local_irq_disable()
raw_local_irq_save() -> local_irq_save()
...
This is quite confusing. There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.
Change this to have the arch provide:
flags = arch_local_save_flags()
flags = arch_local_irq_save()
arch_local_irq_restore(flags)
arch_local_irq_disable()
arch_local_irq_enable()
arch_irqs_disabled_flags(flags)
arch_irqs_disabled()
arch_safe_halt()
Then linux/irqflags.h wraps these to provide:
raw_local_save_flags(flags)
raw_local_irq_save(flags)
raw_local_irq_restore(flags)
raw_local_irq_disable()
raw_local_irq_enable()
raw_irqs_disabled_flags(flags)
raw_irqs_disabled()
raw_safe_halt()
with type checking on the flags 'arguments', and then wraps those to provide:
local_save_flags(flags)
local_irq_save(flags)
local_irq_restore(flags)
local_irq_disable()
local_irq_enable()
irqs_disabled_flags(flags)
irqs_disabled()
safe_halt()
with tracing included if enabled.
The arch functions can now all be inline functions rather than some of them
having to be macros.
Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
With all the recent module loading cleanups, we've minimized the code
that sits under module_mutex, fixing various deadlocks and making it
possible to do most of the module loading in parallel.
However, that whole conversion totally missed the rather obscure code
that adds a new module to the list for BUG() handling. That code was
doubly obscure because (a) the code itself lives in lib/bugs.c (for
dubious reasons) and (b) it gets called from the architecture-specific
"module_finalize()" rather than from generic code.
Calling it from arch-specific code makes no sense what-so-ever to begin
with, and is now actively wrong since that code isn't protected by the
module loading lock any more.
So this commit moves the "module_bug_{finalize,cleanup}()" calls away
from the arch-specific code, and into the generic code - and in the
process protects it with the module_mutex so that the list operations
are now safe.
Future fixups:
- move the module list handling code into kernel/module.c where it
belongs.
- get rid of 'module_bug_list' and just use the regular list of modules
(called 'modules' - imagine that) that we already create and maintain
for other reasons.
Reported-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
flush_icache_range() is given virtual addresses to describe the region. It
deals with these by attempting to translate them through the current set of
page tables.
This is fine for userspace memory and vmalloc()'d areas as they are governed by
page tables. However, since the regions above 0x80000000 aren't translated
through the page tables by the MMU, the kernel doesn't bother to set up page
tables for them (see paging_init()).
This means flush_icache_range() as it stands cannot be used to flush regions of
the VM area between 0x80000000 and 0x9fffffff where the kernel resides if the
data cache is operating in WriteBack mode.
To fix this, make flush_icache_range() first check for addresses in the upper
half of VM space and deal with them appropriately, before dealing with any
range in the page table mapped area.
Ordinarily, this is not a problem, but it has the capacity to make kprobes and
kgdb malfunction. It should not affect gdbstub, signal frame setup or module
loading as gdb has its own flush functions, and the others take place in the
page table mapped area only.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When caching is disabled on the MN10300 arch, the sys_cacheflush()
function is removed by conditional stuff in the makefiles, but is still
referred to by the syscall table.
Provide a null version that just returns 0 when caching is disabled (or
-EINVAL if the arguments are silly).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The configuration choice for the port on which the GDB stub listens has
a default of GDBSTUB_TTYSM0, but this should be GDBSTUB_ON_TTYSM0 to
match the option.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It really has no business being there; short of a serious kernel bug
we should already have USER_DS at that point. It shouldn't have been
done on x86 either...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set ->orig_d0 to -1, same as what sigreturn does
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove specification of HAVE_ARCH_TRACEHOOK for MN10300 as the arch does not
support it at this time.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SIGRTMAX should be _NSIG not _NSIG-1.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MN10300 arch ext2 bitops assume a big-endian kernel, but the MN10300
arch only runs in little-endian mode.
Reported-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the IRQ names for the MN10300 on-chip serial ports in the driver as
request_interrupt() no longer allows names containing slashes, giving a warning
like the following if one is encountered:
------------[ cut here ]------------
WARNING: at fs/proc/generic.c:323 __xlate_proc_name+0x62/0x7c()
name 'ttySM0/Rx'
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dev_name always dereferences its argument, so it should not be called if
the argument is NULL. The function indeed later tests the argument for
being NULL.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression dev,E;
@@
*dev_name(dev)
... when != dev = E
(
*dev == NULL
|
*dev != NULL
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make do_execve() take a const filename pointer so that kernel_execve() compiles
correctly on ARM:
arch/arm/kernel/sys_arm.c:88: warning: passing argument 1 of 'do_execve' discards qualifiers from pointer target type
This also requires the argv and envp arguments to be consted twice, once for
the pointer array and once for the strings the array points to. This is
because do_execve() passes a pointer to the filename (now const) to
copy_strings_kernel(). A simpler alternative would be to cast the filename
pointer in do_execve() when it's passed to copy_strings_kernel().
do_execve() may not change any of the strings it is passed as part of the argv
or envp lists as they are some of them in .rodata, so marking these strings as
const should be fine.
Further kernel_execve() and sys_execve() need to be changed to match.
This has been test built on x86_64, frv, arm and mips.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark arguments to certain system calls as being const where they should be but
aren't. The list includes:
(*) The filename arguments of various stat syscalls, execve(), various utimes
syscalls and some mount syscalls.
(*) The filename arguments of some syscall helpers relating to the above.
(*) The buffer argument of various write syscalls.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use no_printk() for disabled gdbstub debugging functions to maintain side
effect checking.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a dummy printk function for the maintenance of unused printks through gcc
format checking, and also so that side-effect checking is maintained too.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't try and #include <linux/slab.h> in lib/inflate.c from the bootloader code
as linux/slab.h hauls in function defs that aren't available in the bootloader
code and may also haul in conflicting functions.
To fix this, make the inclusion of linux/slab.h contingent on NO_INFLATE_MALLOC
as are the usages of kmalloc() and kfree().
In MN10300, this causes the following errors:
In file included from include/linux/string.h:21,
from include/linux/bitmap.h:8,
from include/linux/nodemask.h:93,
from include/linux/mmzone.h:16,
from include/linux/gfp.h:4,
from include/linux/slab.h:12,
from arch/mn10300/boot/compressed/../../../../lib/inflate.c:106,
from arch/mn10300/boot/compressed/misc.c:170:
/warthog/am33/linux-2.6-mn10300/arch/mn10300/include/asm/string.h:19: error: conflicting types for 'memset'
arch/mn10300/boot/compressed/misc.c:59: error: previous definition of 'memset' was here
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the newer compilers, size_t and ssize_t are expected to be (un)signed int
rather than (un)signed long.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A change to the RTC routines in the MN10300 arch used set_rtc_mms() when it
meant set_rtc_mmss(). This results in an error due to a reference of an
undefined symbol.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN). So we
can unify dma_get_cache_alignment implementations.
Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment. So
fully-coherent architectures should return 1. This patch also fixes this
issue.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now each architecture has the own dma_get_cache_alignment implementation.
dma_get_cache_alignment returns the minimum DMA alignment. Architectures
define it as ARCH_KMALLOC_MINALIGN (it's used to make sure that malloc'ed
buffer is DMA-safe; the buffer doesn't share a cache with the others). So
we can unify dma_get_cache_alignment implementations.
This patch:
dma_get_cache_alignment() needs to know if an architecture defines
ARCH_KMALLOC_MINALIGN or not (needs to know if architecture has DMA
alignment restriction). However, slab.h define ARCH_KMALLOC_MINALIGN if
architectures doesn't define it.
Let's rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN.
ARCH_KMALLOC_MINALIGN is used only in the internals of slab/slob/slub
(except for crypto).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
This patch is against the 2.6.34 source.
Paraphrased from the 1989 BSD patch by David Borman @ cray.com:
These are the changes needed for the kernel to support
LINEMODE in the server.
There is a new bit in the termios local flag word, EXTPROC.
When this bit is set, several aspects of the terminal driver
are disabled. Input line editing, character echo, and mapping
of signals are all disabled. This allows the telnetd to turn
off these functions when in linemode, but still keep track of
what state the user wants the terminal to be in.
New ioctl:
TIOCSIG Generate a signal to processes in the
current process group of the pty.
There is a new mode for packet driver, the TIOCPKT_IOCTL bit.
When packet mode is turned on in the pty, and the EXTPROC bit
is set, then whenever the state of the pty is changed, the
next read on the master side of the pty will have the TIOCPKT_IOCTL
bit set. This allows the process on the server side of the pty
to know when the state of the terminal has changed; it can then
issue the appropriate ioctl to retrieve the new state.
Since the original BSD patches accompanied the source code for telnet
I've left that reference here, but obviously the feature is useful for
any remote terminal protocol, including ssh.
The corresponding feature has existed in the BSD tty driver since 1989.
For historical reference, a good copy of the relevant files can be found
here:
http://anonsvn.mit.edu/viewvc/krb5/trunk/src/appl/telnet/?pathrev=17741
Signed-off-by: Howard Chu <hyc@symas.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Jeff Dike pointed out, the Hayes ESP driver was removed in commit
f53a2ade0b, so these ioctl definitions
should also be removed. This cleans up the remaining arch-specific
locations of this ioctl value.
Thanks to Arnd for pointing these out.
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kunmap_atomic() is currently at level -4 on Rusty's "Hard To Misuse"
list[1] ("Follow common convention and you'll get it wrong"), except in
some architectures when CONFIG_DEBUG_HIGHMEM is set[2][3].
kunmap() takes a pointer to a struct page; kunmap_atomic(), however, takes
takes a pointer to within the page itself. This seems to once in a while
trip people up (the convention they are following is the one from
kunmap()).
Make it much harder to misuse, by moving it to level 9 on Rusty's list[4]
("The compiler/linker won't let you get it wrong"). This is done by
refusing to build if the type of its first argument is a pointer to a
struct page.
The real kunmap_atomic() is renamed to kunmap_atomic_notypecheck()
(which is what you would call in case for some strange reason calling it
with a pointer to a struct page is not incorrect in your code).
The previous version of this patch was compile tested on x86-64.
[1] http://ozlabs.org/~rusty/index.cgi/tech/2008-04-01.html
[2] In these cases, it is at level 5, "Do it right or it will always
break at runtime."
[3] At least mips and powerpc look very similar, and sparc also seems to
share a common ancestor with both; there seems to be quite some
degree of copy-and-paste coding here. The include/asm/highmem.h file
for these three archs mention x86 CPUs at its top.
[4] http://ozlabs.org/~rusty/index.cgi/tech/2008-03-30.html
[5] As an aside, could someone tell me why mn10300 uses unsigned long as
the first parameter of kunmap_atomic() instead of void *?
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Cc: Russell King <linux@arm.linux.org.uk> (arch/arm)
Cc: Ralf Baechle <ralf@linux-mips.org> (arch/mips)
Cc: David Howells <dhowells@redhat.com> (arch/frv, arch/mn10300)
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com> (arch/mn10300)
Cc: Kyle McMartin <kyle@mcmartin.ca> (arch/parisc)
Cc: Helge Deller <deller@gmx.de> (arch/parisc)
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> (arch/parisc)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> (arch/powerpc)
Cc: Paul Mackerras <paulus@samba.org> (arch/powerpc)
Cc: "David S. Miller" <davem@davemloft.net> (arch/sparc)
Cc: Thomas Gleixner <tglx@linutronix.de> (arch/x86)
Cc: Ingo Molnar <mingo@redhat.com> (arch/x86)
Cc: "H. Peter Anvin" <hpa@zytor.com> (arch/x86)
Cc: Arnd Bergmann <arnd@arndb.de> (include/asm-generic)
Cc: Rusty Russell <rusty@rustcorp.com.au> ("Hard To Misuse" list)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-timekeeping-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
um: Fix read_persistent_clock fallout
kgdb: Do not access xtime directly
powerpc: Clean up obsolete code relating to decrementer and timebase
powerpc: Rework VDSO gettimeofday to prevent time going backwards
clocksource: Add __clocksource_updatefreq_hz/khz methods
x86: Convert common clocksources to use clocksource_register_hz/khz
timekeeping: Make xtime and wall_to_monotonic static
hrtimer: Cleanup direct access to wall_to_monotonic
um: Convert to use read_persistent_clock
timkeeping: Fix update_vsyscall to provide wall_to_monotonic offset
powerpc: Cleanup xtime usage
powerpc: Simplify update_vsyscall
time: Kill off CONFIG_GENERIC_TIME
time: Implement timespec_add
x86: Fix vtime/file timestamp inconsistencies
Trivial conflicts in Documentation/feature-removal-schedule.txt
Much less trivial conflicts in arch/powerpc/kernel/time.c resolved as
per Thomas' earlier merge commit 47916be4e2 ("Merge branch
'powerpc.cherry-picks' into timers/clocksource")
Now that all arches have been converted over to use generic time via
clocksources or arch_gettimeoffset(), we can remove the GENERIC_TIME
config option and simplify the generic code.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-4-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: clear bridge resource range if BIOS assigned bad one
PCI: hotplug/cpqphp, fix NULL dereference
Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/"
PCI: change resource collision messages from KERN_ERR to KERN_INFO
Yannick found that video does not work with 2.6.34. The cause of this
bug was that the BIOS had assigned the wrong range to the PCI bridge
above the video device. Before 2.6.34 the kernel would have shrunk
the size of the bridge window, but since
d65245c PCI: don't shrink bridge resources
the kernel will avoid shrinking BIOS ranges.
So zero out the old range if we fail to claim it at boot time; this will
cause us to allocate a new range at startup, restoring the 2.6.34
behavior.
Fixes regression https://bugzilla.kernel.org/show_bug.cgi?id=16009.
Reported-by: Yannick <yannick.roehlly@free.fr>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On 64bit, local_t is of size long, and thus we make local64_t an alias.
On 32bit, we fall back to atomic64_t. (architecture can provide optimized
32-bit version)
(This new facility is to be used by perf events optimizations.)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linux-arch@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As explained in commit 1c0fe6e3bd ("mm: invoke oom-killer from page
fault") , we want to call the architecture independent oom killer when
getting an unexplained OOM from handle_mm_fault, rather than simply
killing current.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe: the
buffer doesn't share a cache with the others.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm-generic/atomic.h has been derived from the mn10300 implementation.
Remove the now duplicated mn10300 implementation by including the generic
version instead.
This adds cmpxchg_local() and cmpxchg64_local() for free to the
architecture, as they are implemented in asm-generic/atomic.h.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Peter Fritzsche <peter.fritzsche@gmx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jamie Lokier <jamie@shareable.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Keith M Wesolowski <wesolows@foobazco.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
* 'timers-for-linus-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
avr32: Fix typo in read_persistent_clock()
sparc: Convert sparc to use read/update_persistent_clock
cris: Convert cris to use read/update_persistent_clock
m68k: Convert m68k to use read/update_persistent_clock
m32r: Convert m32r to use read/update_peristent_clock
blackfin: Convert blackfin to use read/update_persistent_clock
ia64: Convert ia64 to use read/update_persistent_clock
avr32: Convert avr32 to use read/update_persistent_clock
h8300: Convert h8300 to use read/update_persistent_clock
frv: Convert frv to use read/update_persistent_clock
mn10300: Convert mn10300 to use read/update_persistent_clock
alpha: Convert alpha to use read/update_persistent_clock
xtensa: Fix unnecessary setting of xtime
time: Clean up direct xtime usage in xen
In preparation for removing volatile from the atomic_t definition, this
patch adds a volatile cast to all the atomic read functions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This patch converts the mn10300 architecture to use the generic
read_persistent_clock and update_persistent_clock interfaces, reducing
the amount of arch specific code we have to maintain, and allowing for
further cleanups in the future.
I have not built or tested this patch, so help from arch maintainers
would be appreciated.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1267675049-12337-3-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
pci_dma_sync_single was obsoleted long ago.
All the comments are generic, not architecture specific, simply describes
some of the DMA-API (and the same comments are in other files).
Documentation/DMA-API.txt have more detailed descriptions.
This removes the above obsolete and unnecessary DMA API
comments. Let's describe the DMA API in only
Documentation/DMA-API.txt.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While in theory user_enable_single_step/user_disable_single_step/
user_enable_blockstep could also be provided as an inline or macro there's
no good reason to do so, and having the prototype in one places keeps code
size and confusion down.
Roland said:
The original thought there was that user_enable_single_step() et al
might well be only an instruction or three on a sane machine (as if we
have any of those!), and since there is only one call site inlining
would be beneficial. But I agree that there is no strong reason to care
about inlining it.
As to the arch changes, there is only one thought I'd add to the
record. It was always my thinking that for an arch where
PTRACE_SINGLESTEP does text-modifying breakpoint insertion,
user_enable_single_step() should not be provided. That is,
arch_has_single_step()=>true means that there is an arch facility with
"pure" semantics that does not have any unexpected side effects.
Inserting a breakpoint might do very unexpected strange things in
multi-threaded situations. Aside from that, it is a peculiar side
effect that user_{enable,disable}_single_step() should cause COW
de-sharing of text pages and so forth. For PTRACE_SINGLESTEP, all these
peculiarities are the status quo ante for that arch, so having
arch_ptrace() itself do those is one thing. But for building other
things in the future, it is nicer to have a uniform "pure" semantics
that arch-independent code can expect.
OTOH, all such arch issues are really up to the arch maintainer. As
of today, there is nothing but ptrace using user_enable_single_step() et
al so it's a distinction without a practical difference. If/when there
are other facilities that use user_enable_single_step() and might care,
the affected arch's can revisit the question when someone cares about
the quality of the arch support for said new facility.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic implementation of the ipc demultiplexer syscall. Except for
s390 and sparc64 all implementations of the sys_ipc are nearly identical.
There are slight differences in the types of the parameters, where mips
and powerpc as the only 64-bit architectures with sys_ipc use unsigned
long for the "third" argument as it gets casted to a pointer later, while
it traditionally is an "int" like most other paramters. frv goes even
further and uses unsigned long for all parameters execept for "ptr" which
is a pointer type everywhere. The change from int to unsigned long for
"third" and back to "int" for the others on frv should be fine due to the
in-register calling conventions for syscalls (we already had a similar
issue with the generic sys_ptrace), but I'd prefer to have the arch
maintainers looks over this in details.
Except for that h8300, m68k and m68knommu lack an impplementation of the
semtimedop sub call which this patch adds, and various architectures have
gets used - at least on i386 it seems superflous as the compat code on
x86-64 and ia64 doesn't even bother to implement it.
[akpm@linux-foundation.org: add sys_ipc to sys_ni.c]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic implementation of the old select() syscall, which expects
its argument in a memory block and switch all architectures over to use
it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: H. Peter Anvin <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: James Morris <jmorris@namei.org>
Acked-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.
This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On VIVT ARM, when we have multiple shared mappings of the same file
in the same MM, we need to ensure that we have coherency across all
copies. We do this via make_coherent() by making the pages
uncacheable.
This used to work fine, until we allowed highmem with highpte - we
now have a page table which is mapped as required, and is not available
for modification via update_mmu_cache().
Ralf Beache suggested getting rid of the PTE value passed to
update_mmu_cache():
On MIPS update_mmu_cache() calls __update_tlb() which walks pagetables
to construct a pointer to the pte again. Passing a pte_t * is much
more elegant. Maybe we might even replace the pte argument with the
pte_t?
Ben Herrenschmidt would also like the pte pointer for PowerPC:
Passing the ptep in there is exactly what I want. I want that
-instead- of the PTE value, because I have issue on some ppc cases,
for I$/D$ coherency, where set_pte_at() may decide to mask out the
_PAGE_EXEC.
So, pass in the mapped page table pointer into update_mmu_cache(), and
remove the PTE value, updating all implementations and call sites to
suit.
Includes a fix from Stephen Rothwell:
sparc: fix fallout from update_mmu_cache API change
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the defconfig for the ASB2303 platform.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Access to the ASB2305's PCnet32 NIC doesn't work correctly because when
the NIC attempts to update the ring buffer flags by DMA, the change to RAM
crops up about 17uS after the interrupt line is asserted. This is almost
certainly due to a bug in the PCI bridge FPGA on that board.
We can get around this by making dma_alloc_coherent() put the ring buffer
in the SRAM attached to the PCI bridge rather than in the SDRAM.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insert PCI root bus resources for the MN10300-based ASB2305 development
kit motherboard. This is required because the CPU's window onto the PCI
bus address space is considerably smaller than the CPU's full address
space and non-PCI devices lie outside of the PCI window that we might want
to access.
Without this patch, the PCI root bus uses the platform-level bus
resources, and these are then confined to the PCI window, thus making
platform_device_add() reject devices outside of this window.
We also add a reservation for the PCI SRAM region.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the generic pci_enable_resources() instead of the arch-specific code.
Unlike this arch-specific code, the generic version:
- checks PCI_NUM_RESOURCES (11), not 6, resources
- skips resources that have neither IORESOURCE_IO nor IORESOURCE_MEM set
- skips ROM resources unless IORESOURCE_ROM_ENABLE is set
- checks for resource collisions with "!r->parent"
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use KERN_ERR not KERN_ERROR in the ASB2305 platform code.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm/cpu never existed for mn10300; the files they are looking for are in
asm.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wire up missing new system calls for MN10300.
Signed-off-by: David Howells <dhowelsl@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc 4.2.1 for MN10300 is more agressive than the older gcc in
reordering/moving other insns between an insn that sets flags and an insn
that uses those flags. This leads to trouble with asm statements which
are missing an explicit "cc" clobber. This patch adds the explicit "cc"
clobber to asm statements which do indeed clobber the condition flags.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gcc-4.2.1 based toolchain for MN10300 adds some new note sections
which need to be stripped from the binary image. This patch takes care of
that.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a signal stack handling problem in the MN10300 arch. When new
threads are cloned with CLONE_VM, they don't inherit the alternate signal
stack. They do share the signal flags, though. When deciding whether to
use an alternate stack, the arch code needs to check to make sure the task
struct contains a valid alternate stack. This patch fixes the MN10300
arch by using the sas_ss_flags() test provided by sched.h rather than the
on_sig_stack() test which is insufficient by itself.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes it consistent with the extern declaration, used when CONFIG_HIGHMEM
is set Removes redundant casts in printout messages
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-33' of git://repo.or.cz/linux-kbuild: (29 commits)
net: fix for utsrelease.h moving to generated
gen_init_cpio: fixed fwrite warning
kbuild: fix make clean after mismerge
kbuild: generate modules.builtin
genksyms: properly consider EXPORT_UNUSED_SYMBOL{,_GPL}()
score: add asm/asm-offsets.h wrapper
unifdef: update to upstream revision 1.190
kbuild: specify absolute paths for cscope
kbuild: create include/generated in silentoldconfig
scripts/package: deb-pkg: use fakeroot if available
scripts/package: add KBUILD_PKG_ROOTCMD variable
scripts/package: tar-pkg: use tar --owner=root
Kbuild: clean up marker
net: add net_tstamp.h to headers_install
kbuild: move utsrelease.h to include/generated
kbuild: move autoconf.h to include/generated
drop explicit include of autoconf.h
kbuild: move compile.h to include/generated
kbuild: drop include/asm
kbuild: do not check for include/asm-$ARCH
...
Fixed non-conflicting clean merge of modpost.c as per comments from
Stephen Rothwell (modpost.c had grown an include of linux/autoconf.h
that needed to be changed to generated/autoconf.h)
Currently all architectures but microblaze unconditionally define
USE_ELF_CORE_DUMP. The microblaze omission seems like an error to me, so
let's kill this ifdef and make sure we are the same everywhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: <linux-arch@vger.kernel.org>
Cc: Michal Simek <michal.simek@petalogix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
The simplest method was to add an extra asm-offsets.h
file in arch/$ARCH/include/asm that references the generated file.
We can now migrate the architectures one-by-one to reference
the generated file direct - and when done we can delete the
temporary arch/$ARCH/include/asm/asm-offsets.h file.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michal Marek <mmarek@suse.cz>
New helper - sys_mmap_pgoff(); switch syscalls to using it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'bkl-arch-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mn10300: Remove the BKL from sys_execve
m68knommu: Remove the BKL from sys_execve
m68k: Remove the BKL from sys_execve
h83000: Remove BKL from sys_execve
frv: Remove the BKL from sys_execve
blackfin: Remove the BKL from sys_execve
um: Remove BKL from mmapper
um: Remove BKL from random
s390: Remove BKL from prng
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
cfq-iosched: Do not access cfqq after freeing it
block: include linux/err.h to use ERR_PTR
cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
blkio: Allow CFQ group IO scheduling even when CFQ is a module
blkio: Implement dynamic io controlling policy registration
blkio: Export some symbols from blkio as its user CFQ can be a module
block: Fix io_context leak after failure of clone with CLONE_IO
block: Fix io_context leak after clone with CLONE_IO
cfq-iosched: make nonrot check logic consistent
io controller: quick fix for blk-cgroup and modular CFQ
cfq-iosched: move IO controller declerations to a header file
cfq-iosched: fix compile problem with !CONFIG_CGROUP
blkio: Documentation
blkio: Wait on sync-noidle queue even if rq_noidle = 1
blkio: Implement group_isolation tunable
blkio: Determine async workload length based on total number of queues
blkio: Wait for cfq queue to get backlogged if group is empty
blkio: Propagate cgroup weight updation to cfq groups
blkio: Drop the reference to queue once the task changes cgroup
blkio: Provide some isolation between groups
...
Mtdblock driver doesn't call flush_dcache_page for pages in request. So,
this causes problems on architectures where the icache doesn't fill from
the dcache or with dcache aliases. The patch fixes this.
The ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE symbol was introduced to avoid
pointless empty cache-thrashing loops on architectures for which
flush_dcache_page() is a no-op. Every architecture was provided with this
flush pages on architectires where ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE is
equal 1 or do nothing otherwise.
See "fix mtd_blkdevs problem with caches on some architectures" discussion
on LKML for more information.
Signed-off-by: Ilya Loginov <isloginov@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Peter Horton <phorton@bitbox.co.uk>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch updates misc percpu related symbols such that percpu
symbols are unique and don't clash with local symbols. This serves
two purposes of decreasing the possibility of global percpu symbol
collision and allowing dropping per_cpu__ prefix from percpu symbols.
* drivers/crypto/padlock-aes.c: s/last_cword/paes_last_cword/
* drivers/lguest/x86/core.c: s/last_cpu/lg_last_cpu/
* drivers/s390/net/netiucv.c: rename the variable used in a macro to
avoid clashing with percpu symbol
* arch/mn10300/kernel/kprobes.c: replace current_ prefix with cur_ for
static variables. Please note that percpu symbol current_kprobe
can't be changed as it's used by generic code.
Partly based on Rusty Russell's "alloc_percpu: rename percpu vars
which cause name clashes" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
This looks like a cut-and-paste from functionality that no-longer
needs the bkl Just remove it. Also, rewrite slightly so that it looks
closer to sys_execve on other architectures.
Signed-off-by: John Kacur <jkacur@redhat.com>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
LKML-Reference: <alpine.LFD.2.00.0910130016540.3658@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Create a new socket level option to report number of queue overflows
Recently I augmented the AF_PACKET protocol to report the number of frames lost
on the socket receive queue between any two enqueued frames. This value was
exported via a SOL_PACKET level cmsg. AFter I completed that work it was
requested that this feature be generalized so that any datagram oriented socket
could make use of this option. As such I've created this patch, It creates a
new SOL_SOCKET level option called SO_RXQ_OVFL, which when enabled exports a
SOL_SOCKET level cmsg that reports the nubmer of times the sk_receive_queue
overflowed between any two given frames. It also augments the AF_PACKET
protocol to take advantage of this new feature (as it previously did not touch
sk->sk_drops, which this patch uses to record the overflow count). Tested
successfully by me.
Notes:
1) Unlike my previous patch, this patch simply records the sk_drops value, which
is not a number of drops between packets, but rather a total number of drops.
Deltas must be computed in user space.
2) While this patch currently works with datagram oriented protocols, it will
also be accepted by non-datagram oriented protocols. I'm not sure if thats
agreeable to everyone, but my argument in favor of doing so is that, for those
protocols which aren't applicable to this option, sk_drops will always be zero,
and reporting no drops on a receive queue that isn't used for those
non-participating protocols seems reasonable to me. This also saves us having
to code in a per-protocol opt in mechanism.
3) This applies cleanly to net-next assuming that commit
977750076d (my af packet cmsg patch) is reverted
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some build failures when using gcc-4.x for MN10300.
Firstly, __get_user() fails to build because the pointer points to a const and
__gu_val ends up being read-only:
In file included from include/linux/mempolicy.h:62,
from init/main.c:50:
include/linux/pagemap.h: In function 'fault_in_pages_readable':
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:394: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
include/linux/pagemap.h:400: error: read-only variable '__gu_val' used as 'asm' output
make[1]: *** [init/main.o] Error 1
Secondly, gcc-4 doesn't allow casts of lvalues:
UPD include/linux/compile.h
arch/mn10300/kernel/rtc.c: In function 'calibrate_clock':
arch/mn10300/kernel/rtc.c:170: error: lvalue required as left operand of assignment
arch/mn10300/kernel/rtc.c:172: error: lvalue required as left operand of assignment
make[1]: *** [arch/mn10300/kernel/rtc.o] Error 1
These are seen with gcc 4.2.1.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (39 commits)
cpumask: Move deprecated functions to end of header.
cpumask: remove unused deprecated functions, avoid accusations of insanity
cpumask: use new-style cpumask ops in mm/quicklist.
cpumask: use mm_cpumask() wrapper: x86
cpumask: use mm_cpumask() wrapper: um
cpumask: use mm_cpumask() wrapper: mips
cpumask: use mm_cpumask() wrapper: mn10300
cpumask: use mm_cpumask() wrapper: m32r
cpumask: use mm_cpumask() wrapper: arm
cpumask: Use accessors for cpu_*_mask: um
cpumask: Use accessors for cpu_*_mask: powerpc
cpumask: Use accessors for cpu_*_mask: mips
cpumask: Use accessors for cpu_*_mask: m32r
cpumask: remove arch_send_call_function_ipi
cpumask: arch_send_call_function_ipi_mask: s390
cpumask: arch_send_call_function_ipi_mask: powerpc
cpumask: arch_send_call_function_ipi_mask: mips
cpumask: arch_send_call_function_ipi_mask: m32r
cpumask: arch_send_call_function_ipi_mask: alpha
cpumask: remove obsolete topology_core_siblings and topology_thread_siblings: ia64
...
* remove asm/atomic.h inclusion from linux/utsname.h --
not needed after kref conversion
* remove linux/utsname.h inclusion from files which do not need it
NOTE: it looks like fs/binfmt_elf.c do not need utsname.h, however
due to some personality stuff it _is_ needed -- cowardly leave ELF-related
headers and files alone.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes code futureproof against the impending change to mm->cpu_vm_mask
(to be a pointer).
It's also a chance to use the new cpumask_ ops which take a pointer
(the older ones are deprecated, but there's no hurry for arch code).
Also change the actual arg name here to "mm" (which it is), not "task".
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (30 commits)
Use macros for .data.page_aligned section.
Use macros for .bss.page_aligned section.
Use new __init_task_data macro in arch init_task.c files.
kbuild: Don't define ALIGN and ENTRY when preprocessing linker scripts.
arm, cris, mips, sparc, powerpc, um, xtensa: fix build with bash 4.0
kbuild: add static to prototypes
kbuild: fail build if recordmcount.pl fails
kbuild: set -fconserve-stack option for gcc 4.5
kbuild: echo the record_mcount command
gconfig: disable "typeahead find" search in treeviews
kbuild: fix cc1 options check to ensure we do not use -fPIC when compiling
checkincludes.pl: add option to remove duplicates in place
markup_oops: use modinfo to avoid confusion with underscored module names
checkincludes.pl: provide usage helper
checkincludes.pl: close file as soon as we're done with it
ctags: usability fix
kernel hacking: move STRIP_ASM_SYMS from General
gitignore usr/initramfs_data.cpio.bz2 and usr/initramfs_data.cpio.lzma
kbuild: Check if linker supports the -X option
kbuild: introduce ld-option
...
Fix trivial conflict in scripts/basic/fixdep.c
Commit ebd2c8f6d2 removed struct uart_info and
commit bdc04e3174 further moved delta_msr_wait.
Fix up the MN10300 on-chip serial port drivers to comply with this.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup
No need for redeclaration.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make all seq_operations structs const, to help mitigate against
revectoring user-triggerable function pointers.
This is derived from the grsecurity patch, although generated from scratch
because it's simpler than extracting the changes from there.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
A number of architectures have identical asm/mman.h files so they can all
be merged by using the new generic file.
The remaining asm/mman.h files are substantially different from each
other.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a flag for mmap that will be used to request a huge page region that
will look like anonymous memory to user space. This is accomplished by
using a file on the internal vfsmount. MAP_HUGETLB is a modifier of
MAP_ANONYMOUS and so must be specified with it. The region will behave
the same as a MAP_ANONYMOUS region using small pages.
The patch also adds the MAP_STACK flag, which was previously defined only
on some architectures but not on others. Since MAP_STACK is meant to be a
hint only, architectures can define it without assigning a specific
meaning to it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric B Munson <ebmunson@us.ibm.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: David Rientjes <rientjes@google.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9617729941 ("Drop free_pages()")
modified nr_free_pages() to return 'unsigned long' instead of 'unsigned
int'. This made the casts to 'unsigned long' in most callers superfluous,
so remove them.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <zankel@tensilica.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bye-bye Performance Counters, welcome Performance Events!
In the past few months the perfcounters subsystem has grown out its
initial role of counting hardware events, and has become (and is
becoming) a much broader generic event enumeration, reporting, logging,
monitoring, analysis facility.
Naming its core object 'perf_counter' and naming the subsystem
'perfcounters' has become more and more of a misnomer. With pending
code like hw-breakpoints support the 'counter' name is less and
less appropriate.
All in one, we've decided to rename the subsystem to 'performance
events' and to propagate this rename through all fields, variables
and API names. (in an ABI compatible fashion)
The word 'event' is also a bit shorter than 'counter' - which makes
it slightly more convenient to write/handle as well.
Thanks goes to Stephane Eranian who first observed this misnomer and
suggested a rename.
User-space tooling and ABI compatibility is not affected - this patch
should be function-invariant. (Also, defconfigs were not touched to
keep the size down.)
This patch has been generated via the following script:
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/PERF_EVENT_/PERF_RECORD_/g' \
-e 's/PERF_COUNTER/PERF_EVENT/g' \
-e 's/perf_counter/perf_event/g' \
-e 's/nb_counters/nb_events/g' \
-e 's/swcounter/swevent/g' \
-e 's/tpcounter_event/tp_event/g' \
$FILES
for N in $(find . -name perf_counter.[ch]); do
M=$(echo $N | sed 's/perf_counter/perf_event/g')
mv $N $M
done
FILES=$(find . -name perf_event.*)
sed -i \
-e 's/COUNTER_MASK/REG_MASK/g' \
-e 's/COUNTER/EVENT/g' \
-e 's/\<event\>/event_id/g' \
-e 's/counter/event/g' \
-e 's/Counter/Event/g' \
$FILES
... to keep it as correct as possible. This script can also be
used by anyone who has pending perfcounters patches - it converts
a Linux kernel tree over to the new naming. We tried to time this
change to the point in time where the amount of pending patches
is the smallest: the end of the merge window.
Namespace clashes were fixed up in a preparatory patch - and some
stylistic fallout will be fixed up in a subsequent patch.
( NOTE: 'counters' are still the proper terminology when we deal
with hardware registers - and these sed scripts are a bit
over-eager in renaming them. I've undone some of that, but
in case there's something left where 'counter' would be
better than 'event' we can undo that on an individual basis
instead of touching an otherwise nicely automated patch. )
Suggested-by: Stephane Eranian <eranian@google.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Paul Mackerras <paulus@samba.org>
Reviewed-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
We moved this into uart_state, now move the fields out of the separate
structure and kill it off.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (75 commits)
PCI hotplug: clean up acpi_run_hpp()
PCI hotplug: acpiphp: use generic pci_configure_slot()
PCI hotplug: shpchp: use generic pci_configure_slot()
PCI hotplug: pciehp: use generic pci_configure_slot()
PCI hotplug: add pci_configure_slot()
PCI hotplug: clean up acpi_get_hp_params_from_firmware() interface
PCI hotplug: acpiphp: don't cache hotplug_params in acpiphp_bridge
PCI hotplug: acpiphp: remove superfluous _HPP/_HPX evaluation
PCI: Clear saved_state after the state has been restored
PCI PM: Return error codes from pci_pm_resume()
PCI: use dev_printk in quirk messages
PCI / PCIe portdrv: Fix pcie_portdrv_slot_reset()
PCI Hotplug: convert acpi_pci_detect_ejectable() to take an acpi_handle
PCI Hotplug: acpiphp: find bridges the easy way
PCI: pcie portdrv: remove unused variable
PCI / ACPI PM: Propagate wake-up enable for devices w/o ACPI support
ACPI PM: Replace wakeup.prepared with reference counter
PCI PM: Introduce device flag wakeup_prepared
PCI / ACPI PM: Rework some debug messages
PCI PM: Simplify PCI wake-up code
...
Fixed up conflict in arch/powerpc/kernel/pci_64.c due to OF device tree
scanning having been moved and merged for the 32- and 64-bit cases. The
'needs_freset' initialization added in 6e19314cc ("PCI/powerpc: support
PCIe fundamental reset") is now in arch/powerpc/kernel/pci_of_scan.c.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (46 commits)
powerpc64: convert to dynamic percpu allocator
sparc64: use embedding percpu first chunk allocator
percpu: kill lpage first chunk allocator
x86,percpu: use embedding for 64bit NUMA and page for 32bit NUMA
percpu: update embedding first chunk allocator to handle sparse units
percpu: use group information to allocate vmap areas sparsely
vmalloc: implement pcpu_get_vm_areas()
vmalloc: separate out insert_vmalloc_vm()
percpu: add chunk->base_addr
percpu: add pcpu_unit_offsets[]
percpu: introduce pcpu_alloc_info and pcpu_group_info
percpu: move pcpu_lpage_build_unit_map() and pcpul_lpage_dump_cfg() upward
percpu: add @align to pcpu_fc_alloc_fn_t
percpu: make @dyn_size mandatory for pcpu_setup_first_chunk()
percpu: drop @static_size from first chunk allocators
percpu: generalize first chunk allocator selection
percpu: build first chunk allocators selectively
percpu: rename 4k first chunk allocator to page
percpu: improve boot messages
percpu: fix pcpu_reclaim() locking
...
Fix trivial conflict as by Tejun Heo in kernel/sched.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
This was #define'd as 0 on all platforms, so let's get rid of it.
This change makes pci_scan_slot() slightly easier to read.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add a keyctl to install a process's session keyring onto its parent. This
replaces the parent's session keyring. Because the COW credential code does
not permit one process to change another process's credentials directly, the
change is deferred until userspace next starts executing again. Normally this
will be after a wait*() syscall.
To support this, three new security hooks have been provided:
cred_alloc_blank() to allocate unset security creds, cred_transfer() to fill in
the blank security creds and key_session_to_parent() - which asks the LSM if
the process may replace its parent's session keyring.
The replacement may only happen if the process has the same ownership details
as its parent, and the process has LINK permission on the session keyring, and
the session keyring is owned by the process, and the LSM permits it.
Note that this requires alteration to each architecture's notify_resume path.
This has been done for all arches barring blackfin, m68k* and xtensa, all of
which need assembly alteration to support TIF_NOTIFY_RESUME. This allows the
replacement to be performed at the point the parent process resumes userspace
execution.
This allows the userspace AFS pioctl emulation to fully emulate newpag() and
the VIOCSETTOK and VIOCSETTOK2 pioctls, all of which require the ability to
alter the parent process's PAG membership. However, since kAFS doesn't use
PAGs per se, but rather dumps the keys into the session keyring, the session
keyring of the parent must be replaced if, for example, VIOCSETTOK is passed
the newpag flag.
This can be tested with the following program:
#include <stdio.h>
#include <stdlib.h>
#include <keyutils.h>
#define KEYCTL_SESSION_TO_PARENT 18
#define OSERROR(X, S) do { if ((long)(X) == -1) { perror(S); exit(1); } } while(0)
int main(int argc, char **argv)
{
key_serial_t keyring, key;
long ret;
keyring = keyctl_join_session_keyring(argv[1]);
OSERROR(keyring, "keyctl_join_session_keyring");
key = add_key("user", "a", "b", 1, keyring);
OSERROR(key, "add_key");
ret = keyctl(KEYCTL_SESSION_TO_PARENT);
OSERROR(ret, "KEYCTL_SESSION_TO_PARENT");
return 0;
}
Compiled and linked with -lkeyutils, you should see something like:
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: _ses
355907932 --alswrv 4043 -1 \_ keyring: _uid.4043
[dhowells@andromeda ~]$ /tmp/newpag
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: _ses
1055658746 --alswrv 4043 4043 \_ user: a
[dhowells@andromeda ~]$ /tmp/newpag hello
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: hello
340417692 --alswrv 4043 4043 \_ user: a
Where the test program creates a new session keyring, sticks a user key named
'a' into it and then installs it on its parent.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Geert Uytterhoeven
David Howells
Paul Bolle
Yong Zhang
Linus Torvalds
Al Viro
Matt Fleming
Thomas Gleixner
Anna-Maria Gleixner
Suresh Siddha
Srivatsa S. Bhat
Eric B Munson
Cong Wang
Cong Wang
Ben Greear
Bjorn Helgaas
Pavel Emelyanov
H. Peter Anvin
Joe Perches
Myron Stowe
Michael S. Tsirkin
Tejun Heo
John W. Linville
Johannes Berg
Andy Shevchenko
John Stultz
NeilBrown
Arun Sharma
Akinobu Mita
Mike Frysinger
Mathias Krause
Jonas Bonn
Eric W. Biederman
Daniel Lezcano
KOSAKI Motohiro
Peter Zijlstra
Lucas De Marchi
Richard Henderson
FUJITA Tomonori
Eric Dumazet
Tkhai Kirill
Torben Hohn
David Rientjes
Stephen Hemminger
Andrew Morton
Nicolas Pitre
Arnd Bergmann
Namhyung Kim
Akira Takeuchi
Mark Salter
David Howells
Justin Chen
Stoyan Gaydarov
Jeff Mahoney
Michal Marek
Al Viro
Arnaud Lacombe
Julia Lawall
Sam Ravnborg
hyc@symas.com
Greg Kroah-Hartman
Cesar Eduardo Barros
John Stultz
Ingo Molnar
Yinghai Lu
Nick Piggin
Mathieu Desnoyers
Anton Blanchard
Andreas Dilger
Christoph Hellwig
Bjorn Helgaas
Dominik Brodowski
Russell King
Andreas Fenkart
Ilya Loginov
John Kacur
Neil Horman
Tim Abbott
Alexey Dobriyan
Rusty Russell
James Morris
Geert Uytterhoeven
Uwe Kleine-Koenig
Alan Cox
Alex Chiang