[ Upstream commit 0f6b380d58 ]
The firmware for the modem and WiFi subsystems platform specific and is
signed with a OEM specific key (or a test key). In order to support more
than a single device it is therefor not possible to rely on the default
path and stash these files directly in the firmware directory.
This has already been addressed for other platforms, but the APQ8016 SBC
(aka db410c) was never finished upstream.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210531224453.783218-1-bjorn.andersson@linaro.org
Stable-dep-of: e27654df20 ("arm64: dts: qcom: apq8016-sbc: Fix regulator constraints")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70be83708c ]
PSCI is not implemented on SparX-5 at all, there is no ATF and U-boot that
is shipped does not implement it as well.
I have tried flashing the latest BSP 2022.12 U-boot which did not work.
After contacting Microchip, they confirmed that there is no ATF for the
SoC nor PSCI implementation which is unfortunate in 2023.
So, disable PSCI as otherwise kernel crashes as soon as it tries probing
PSCI with, and the crash is only visible if earlycon is used.
Since PSCI is not implemented, switch core bringup to use spin-tables
which are implemented in the vendor U-boot and actually work.
Tested on PCB134 with eMMC (VSC5640EV).
Fixes: 6694aee00a ("arm64: dts: sparx5: Add basic cpu support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Acked-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/20230221105039.316819-1-robert.marko@sartura.hr
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bf2e53431 ]
The final production baseboard had a different chip select than
earlier prototype boards. When the newer board was released,
the SPI stopped working because the wrong pin was used in the device
tree and conflicted with the UART RTS. Fix the pinmux for
production boards.
Fixes: 36ca3c8ccb ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca50d77655 ]
Add the assigned-clocks and assigned-clock-rates properties for the
LPUARTx nodes. Without these properties, the default clock rate
used would be 0, which can cause the UART ports to fail when open.
Fixes: 35f4e9d753 ("arm64: dts: imx8: split adma ss into dma and audio ss")
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a735530c1 ]
In general, the three SKUs of sc7180 (lite, normal, and pro) are
handled dynamically.
The cpufreq table in sc7180.dtsi includes the superset of all CPU
frequencies. The "qcom-cpufreq-hw" driver in Linux shows that we can
dynamically detect which frequencies are actually available on the
currently running CPU and then we can just enable those ones.
The GPU is similarly dynamic. The nvmem has a fuse in it (see
"gpu_speed_bin" in sc7180.dtsi) that the GPU driver can use to figure
out which frequencies to enable.
There is one part, however, that is not so dynamic. The way SDRAM
frequency works in sc7180 is that it's tied to cpufreq. At the busiest
cpufreq operating points we'll pick the top supported SDRAM frequency.
They ramp down together.
For the "pro" SKU of sc7180, we only enable one extra cpufreq step.
That extra cpufreq step runs SDRAM at the same speed as the step
below. Thus, for normal and pro things are OK. There is no sc7180-pro
device tree snippet.
For the "lite" SKU if sc7180, however, things aren't so easy. The
"lite" SKU drops 3 cpufreq entries but can still run SDRAM at max
frequency. That messed things up with the whole scheme. This is why we
added the "sc7180-lite" fragment in commit 8fd01e01fd ("arm64: dts:
qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite").
When the lite scheme came about, it was agreed that the WiFi SKUs of
lazor would _always_ be "lite" and would, in fact, be the only "lite"
devices. Unfortunately, this decision changed and folks didn't realize
that it would be a problem. Specifically, some later lazor WiFi-only
devices were built with "pro" CPUs.
Building WiFi-only lazor with "pro" CPUs isn't the end of the world.
The SDRAM will ramp up a little sooner than it otherwise would, but
aside from a small power hit things work OK. One problem, though, is
that the SDRAM scaling becomes a bit quirky. Specifically, with the
current tables we'll max out SDRAM frequency at 2.1GHz but then
_lower_ it at 2.2GHz / 2.3GHz only to raise it back to max for 2.4GHz
and 2.55GHz.
Let's at least fix this so that the SDRAM frequency doesn't go down in
that quirky way. On true "lite" SKUs this change will be a no-op
because the operating points we're touching are disabled. This change
is only useful when a board that thinks it has a "lite" CPU actually
has a "normal" or "pro" one stuffed.
Fixes: 8fd01e01fd ("arm64: dts: qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230515171929.1.Ic8dee2cb79ce39ffc04eab2a344dde47b2f9459f@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0abde8062 ]
Like the other calls in this function virt_to_page() expects
a pointer, not an integer.
However since many architectures implement virt_to_pfn() as
a macro, this function becomes polymorphic and accepts both a
(unsigned long) and a (void *).
Fix this up with an explicit cast.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: http://lists.infradead.org/pipermail/linux-arm-kernel/2023-May/832583.html
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f161cea5a2 upstream.
While testing the ethernet interface on a Variscite symphony carrier
board using an imx8mn SOM with an onboard ADIN1300 PHY (EC hardware
configuration), the ethernet PHY is not detected.
The ADIN1300 datasheet indicate that the "Management interface
active (t4)" state is reached at most 5ms after the reset signal is
deasserted.
The device tree in Variscite custom git repository uses the following
property:
phy-reset-post-delay = <20>;
Add a new MDIO property 'reset-deassert-us' of 20ms to have the same
delay inside the ethphy node. Adding this property fixes the problem
with the PHY detection.
Note that this SOM can also have an Atheros AR8033 PHY. In this case,
a 1ms deassert delay is sufficient. Add a comment to that effect.
Fixes: ade0176dd8 ("arm64: dts: imx8mn-var-som: Add Variscite VAR-SOM-MX8MN System on Module")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2efbafb91e upstream.
Consider the following sequence of events:
1) A page in a PROT_READ|PROT_WRITE VMA is faulted.
2) Page migration allocates a page with the KASAN allocator,
causing it to receive a non-match-all tag, and uses it
to replace the page faulted in 1.
3) The program uses mprotect() to enable PROT_MTE on the page faulted in 1.
As a result of step 3, we are left with a non-match-all tag for a page
with tags accessible to userspace, which can lead to the same kind of
tag check faults that commit e74a684680 ("arm64: Reset KASAN tag in
copy_highpage with HW tags only") intended to fix.
The general invariant that we have for pages in a VMA with VM_MTE_ALLOWED
is that they cannot have a non-match-all tag. As a result of step 2, the
invariant is broken. This means that the fix in the referenced commit
was incomplete and we also need to reset the tag for pages without
PG_mte_tagged.
Fixes: e5b8d92189 ("arm64: mte: reset the page tag in page->flags")
Cc: <stable@vger.kernel.org> # 5.15
Link: https://linux-review.googlesource.com/id/I7409cdd41acbcb215c2a7417c1e50d37b875beff
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20230420210945.2313627-1-pcc@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0af0537e2 ]
Add missing dwc3 quirks from msm-3.18. Unfortunately, none of them
make `dwc3-qcom 6af8800.usb: HS-PHY not in L2` go away.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230302011849.1873056-1-konrad.dybcio@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 44750f1536 upstream.
While stressing EAS on my dragonboard RB3, I have noticed that LITTLE cores
where never selected as the most energy efficient CPU whatever the
utilization level of waking task.
energy model framework uses its cost field to estimate the energy with
the formula:
nrg = cost of the selected OPP * utilization / CPU's max capacity
which ends up selecting the CPU with lowest cost / max capacity ration
as long as the utilization fits in the OPP's capacity.
If we compare the cost of a little OPP with similar capacity of a big OPP
like :
OPP(kHz) OPP capacity cost max capacity cost/max capacity
LITTLE 1766400 407 351114 407 863
big 1056000 408 520267 1024 508
This can be interpreted as the LITTLE core consumes 70% more than big core
for the same compute capacity.
According to [1], LITTLE consumes 10% less than big core for Coremark
benchmark at those OPPs. If we consider that everything else stays
unchanged, the dynamic-power-coefficient of LITTLE core should be
only 53% of the current value: 290 * 53% = 154
Set the dynamic-power-coefficient of CPU0-3 to 154 to fix the energy model.
[1] https://github.com/kdrag0n/freqbench/tree/master/results/sdm845/main
Fixes: 0e0a8e35d7 ("arm64: dts: qcom: sdm845: correct dynamic power coefficients")
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106164618.1845281-1-vincent.guittot@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit af6c0bd59f ]
Currently only the first attempt to single-step has any effect. After
that all further stepping remains "stuck" at the same program counter
value.
Refer to the ARM Architecture Reference Manual (ARM DDI 0487E.a) D2.12,
PSTATE.SS=1 should be set at each step before transferring the PE to the
'Active-not-pending' state. The problem here is PSTATE.SS=1 is not set
since the second single-step.
After the first single-step, the PE transferes to the 'Inactive' state,
with PSTATE.SS=0 and MDSCR.SS=1, thus PSTATE.SS won't be set to 1 due to
kernel_active_single_step()=true. Then the PE transferes to the
'Active-pending' state when ERET and returns to the debugger by step
exception.
Before this patch:
==================
Entering kdb (current=0xffff3376039f0000, pid 1) on processor 0 due to Keyboard Entry
[0]kdb>
[0]kdb>
[0]kdb> bp write_sysrq_trigger
Instruction(i) BP #0 at 0xffffa45c13d09290 (write_sysrq_trigger)
is enabled addr at ffffa45c13d09290, hardtype=0 installed=0
[0]kdb> go
$ echo h > /proc/sysrq-trigger
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to Breakpoint @ 0xffffad651a309290
[1]kdb> ss
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to SS trap @ 0xffffad651a309294
[1]kdb> ss
Entering kdb (current=0xffff4f7e453f8000, pid 175) on processor 1 due to SS trap @ 0xffffad651a309294
[1]kdb>
After this patch:
=================
Entering kdb (current=0xffff6851c39f0000, pid 1) on processor 0 due to Keyboard Entry
[0]kdb> bp write_sysrq_trigger
Instruction(i) BP #0 at 0xffffc02d2dd09290 (write_sysrq_trigger)
is enabled addr at ffffc02d2dd09290, hardtype=0 installed=0
[0]kdb> go
$ echo h > /proc/sysrq-trigger
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to Breakpoint @ 0xffffc02d2dd09290
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd09294
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd09298
[1]kdb> ss
Entering kdb (current=0xffff6851c53c1840, pid 174) on processor 1 due to SS trap @ 0xffffc02d2dd0929c
[1]kdb>
Fixes: 44679a4f14 ("arm64: KGDB: Add step debugging support")
Co-developed-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20230202073148.657746-3-sumit.garg@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52e2996f25 ]
The hid-over-i2c takes VDD, not VCC supply. Fix copy-pasta from other
boards which use elan,ekth3000 with valid VCC:
sc7180-trogdor-lazor-limozeen-nots-r4.dtb: trackpad@2c: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: 2c26adb8db ("arm64: dts: qcom: Add sc7180-lazor-limozeen skus")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e115a4495d ]
For 1MiB of the I/O region, the I/O ports of the legacy PCI devices are
located in the range of 0x0 to 0x100000. Hence, fix the bogus PCI addresses
(0x60200000, 0x40200000, 0x64200000) specified in the ranges property for
I/O region.
While at it, let's use the missing 0x prefix for the addresses.
Fixes: e53bdfc009 ("arm64: dts: qcom: sm8250: Add PCIe support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/linux-arm-msm/7c5dfa87-41df-4ba7-b0e4-72c8386402a8@app.fastmail.com/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230228164752.55682-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf0ac10feb ]
For 1MiB of the I/O region, the I/O ports of the legacy PCI devices are
located in the range of 0x0 to 0x100000. Hence, fix the bogus PCI addresses
(0x0c200000, 0x0d200000, 0x0e200000) specified in the ranges property for
I/O region.
While at it, let's also align the entries.
Fixes: ed965ef892 ("arm64: dts: qcom: msm8996: add support to pcie")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/linux-arm-msm/7c5dfa87-41df-4ba7-b0e4-72c8386402a8@app.fastmail.com/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230228164752.55682-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75a6e1fdb3 ]
For 64KiB of the I/O region, the I/O ports of the legacy PCI devices are
located in the range of 0x0 to 0x10000. Hence, fix the bogus PCI address
(0x20200000) specified in the ranges property for I/O region.
While at it, let's use the missing 0x prefix for the addresses.
Fixes: 095bbdd9a5 ("arm64: dts: qcom: ipq6018: Add pcie support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/linux-arm-msm/7c5dfa87-41df-4ba7-b0e4-72c8386402a8@app.fastmail.com/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230228164752.55682-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e49eafefe5 ]
For 64KiB of the I/O region, the I/O ports of the legacy PCI devices are
located in the range of 0x0 to 0x10000. Hence, fix the bogus PCI addresses
(0x10200000, 0x20200000) specified in the ranges property for I/O region.
While at it, let's use the missing 0x prefix for the addresses and align
them in a single line.
Fixes: 33057e1672 ("ARM: dts: ipq8074: Add pcie nodes")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/linux-arm-msm/7c5dfa87-41df-4ba7-b0e4-72c8386402a8@app.fastmail.com/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230228164752.55682-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67aa109eee ]
For 1MiB of the I/O region, the I/O ports of the legacy PCI devices are
located in the range of 0x0 to 0x100000. Hence, fix the bogus PCI addresses
(0x60200000, 0x40200000) specified in the ranges property for I/O region.
While at it, let's use the missing 0x prefix for the addresses.
Fixes: 42ad231338 ("arm64: dts: qcom: sdm845: Add second PCIe PHY and controller")
Fixes: 5c538e09cb ("arm64: dts: qcom: sdm845: Add first PCIe controller and PHY")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/linux-arm-msm/7c5dfa87-41df-4ba7-b0e4-72c8386402a8@app.fastmail.com/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230228164752.55682-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e0a8e35d7 ]
Following sm8150/sm8250 update sdm845 capacity-dmips-mhz and
dynamic-power-coefficient based on the measurements [1], [2].
The energy model dynamic-power-coefficient values were calculated with
DPC = µW / MHz / V^2
for each OPP, and averaged across all OPPs within each cluster for the
final coefficient. Voltages were obtained from the qcom-cpufreq-hw
driver that reads voltages from the OSM LUT programmed into the SoC.
Normalized DMIPS/MHz capacity scale values for each CPU were calculated
from CoreMarks/MHz (CoreMark iterations per second per MHz), which
serves the same purpose. For each CPU, the final capacity-dmips-mhz
value is the C/MHz value of its maximum frequency normalized to
SCHED_CAPACITY_SCALE (1024) for the fastest CPU in the system.
For more details on measurement process see the commit message for the
commit 6aabed5526 ("arm64: dts: qcom: sm8250: Add CPU capacities and
energy model").
[1] https://github.com/kdrag0n/freqbench
[2] https://github.com/kdrag0n/freqbench/tree/master/results/sdm845/main
Cc: Danny Lin <danny@kdrag0n.dev>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220315141104.730235-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ded8f22945 ]
As part of ARCH_BCM4908 to ARCH_BCMBCA migration, move the BCM4908 dts
files to bcmbca folder and use CONFIG_ARCH_BCMBCA to build all the
BCM4908 board dts. Delete bcm4908 folder and its makefile as well.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20220803175455.47638-5-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Stable-dep-of: 5cca024494 ("arm64: dts: broadcom: bcmbca: bcm4908: fix NAND interrupt name")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ba56aeb39 ]
Add DTS for ARMv8 based broadband SoC BCM4912. bcm4912.dtsi is the
SoC description DTS header and bcm94912.dts is a simple DTS file for
Broadcom BCM94912 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Stable-dep-of: 5cca024494 ("arm64: dts: broadcom: bcmbca: bcm4908: fix NAND interrupt name")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0e68d354f ]
It's a home router based on BCM4908 SoC. It has: 1 GiB of RAM, 512 MiB
NAND flash, 6 Ethernet ports and 3 x BCM43684 (WiFi). One of Ethernet
ports is "2.5 G Multi-Gig port" that isn't described yet (it isn't known
how it's wired up).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Stable-dep-of: 5cca024494 ("arm64: dts: broadcom: bcmbca: bcm4908: fix NAND interrupt name")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f4b30a777 ]
According to latest errata of J721e [1], (i2024) 'MMCSD: Peripherals
Do Not Support HS400' which applies to MMCSD0 subsystem. Speed modes
supported has been already updated but missed dropping 'ti,strobe-sel'
property which is only required by HS400 speed mode.
Thus, drop 'ti,strobe-sel' property from kernel dtsi for J721e SoC.
[1] https://www.ti.com/lit/er/sprz455/sprz455.pdf
Fixes: eb8f6194e8 ("arm64: dts: ti: k3-j721e-main: Update the speed modes supported and their itap delay values for MMCSD subsystems")
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Diwakar Dhyani <d-dhyani@ti.com>
Reviewed-by: Nitin Yadav <n-yadav@ti.com>
Link: https://lore.kernel.org/r/20230203073724.29529-1-b-kapoor@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 554edc3e92 ]
According to the RZ/G Series, 2nd Generation Hardware User’s Manual
Rev. 1.11, the System CPU cores on RZ/G2E do not have their own power
supply, but use the common internal power supply (typical 1.03V).
Hence remove the "opp-microvolt" properties from the Operating
Performance Points table. They are optional, and unused, when none of
the CPU nodes is tied to a regulator using the "cpu-supply" property.
Fixes: 231d8908a6 ("arm64: dts: renesas: r8a774c0: Add OPPs table for cpu devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/8348e18a011ded94e35919cd8e17c0be1f9acf2f.1676560856.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb76b0fae3 ]
According to the R-Car Series, 3rd Generation Hardware User’s Manual
Rev. 2.30, the System CPU cores on R-Car E3 do not have their own power
supply, but use the common internal power supply (typical 1.03V).
Hence remove the "opp-microvolt" properties from the Operating
Performance Points table. They are optional, and unused, when none of
the CPU nodes is tied to a regulator using the "cpu-supply" property.
Fixes: dd7188eb4e ("arm64: dts: renesas: r8a77990: Add OPPs table for cpu devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/9232578d9d395d529f64db3333a371e31327f459.1676560856.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 59b37fe52f upstream.
Instead of reloading the shadow call stack pointer from the ordinary
stack, which may be vulnerable to the kind of gadget based attacks
shadow call stacks were designed to prevent, let's store a task's shadow
call stack pointer in the task struct when switching to the shadow IRQ
stack.
Given that currently, the task_struct::scs_sp field is only used to
preserve the shadow call stack pointer while a task is scheduled out or
running in user space, reusing this field to preserve and restore it
while running off the IRQ stack must be safe, as those occurrences are
guaranteed to never overlap. (The stack switching logic only switches
stacks when running from the task stack, and so the value being saved
here always corresponds to the task mode shadow stack)
While at it, fold a mov/add/mov sequence into a single add.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20230109174800.3286265-3-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2198d07c50 upstream.
All occurrences of the scs_load macro load the value of the shadow call
stack pointer from the task which is current at that point. So instead
of taking a task struct register argument in the scs_load macro to
specify the task struct to load from, let's always reference the current
task directly. This should make it much harder to exploit any
instruction sequences reloading the shadow call stack pointer register
from memory.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230109174800.3286265-2-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a25bc8486f upstream.
The KVM_REG_SIZE() comes from the ioctl and it can be a power of two
between 0-32768 but if it is more than sizeof(long) this will corrupt
memory.
Fixes: 99adb56763 ("KVM: arm/arm64: Add save/restore support for firmware workaround state")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/4efbab8c-640f-43b2-8ac6-6d68e08280fe@kili.mountain
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
[will: kvm_arm_set_fw_reg() lives in psci.c not hypercalls.c]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13ec9308a8 upstream.
Read mmu_invalidate_seq before dropping the mmap_lock so that KVM can
detect if the results of vma_lookup() (e.g. vma_shift) become stale
before it acquires kvm->mmu_lock. This fixes a theoretical bug where a
VMA could be changed by userspace after vma_lookup() and before KVM
reads the mmu_invalidate_seq, causing KVM to install page table entries
based on a (possibly) no-longer-valid vma_shift.
Re-order the MMU cache top-up to earlier in user_mem_abort() so that it
is not done after KVM has read mmu_invalidate_seq (i.e. so as to avoid
inducing spurious fault retries).
This bug has existed since KVM/ARM's inception. It's unlikely that any
sane userspace currently modifies VMAs in such a way as to trigger this
race. And even with directed testing I was unable to reproduce it. But a
sufficiently motivated host userspace might be able to exploit this
race.
Fixes: 94f8e6418d ("KVM: ARM: Handle guest faults in KVM")
Cc: stable@vger.kernel.org
Reported-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: David Matlack <dmatlack@google.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230313235454.2964067-1-dmatlack@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
[will: Use FSC_PERM instead of ESR_ELx_FSC_PERM. Read 'mmu_notifier_seq'
instead of 'mmu_invalidate_seq'. Fix up function references in comment.]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 85af7ffd24 ]
The osc_32k supports #clock-cells as 0, using an id is wrong, drop it.
Fixes: a6a355ede5 ("arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aec4353114 ]
According to S905X2 Datasheet - Revision 07:
DRAM Memory Controller (DMC) register area spans ff638000-ff63a000.
According to DeviceTree Specification - Release v0.4-rc1:
simple-bus nodes do not require reg property.
Fixes: 1499218c80 ("arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi")
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230327120932.2158389-2-mgonzalez@freebox.fr
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72630ba422 ]
Correct PCIe PHY enablement to refer the QMP device nodes rather than
PHY device nodes. QMP nodes have 'status = "disabled"' property in the
ipq8074.dtsi, while PHY nodes do not correspond to the actual device and
do not have the status property.
Fixes: e8a7fdc505 ("arm64: dts: ipq8074: qcom: Re-arrange dts nodes based on address")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324021651.1799969-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f9ea835e99 upstream.
Currently, with VHE, KVM enables the EL0 event counting for the
guest on vcpu_load() or KVM enables it as a part of the PMU
register emulation process, when needed. However, in the migration
case (with VHE), the same handling is lacking, as vPMU register
values that were restored by userspace haven't been propagated yet
(the PMU events haven't been created) at the vcpu load-time on the
first KVM_RUN (kvm_vcpu_pmu_restore_guest() called from vcpu_load()
on the first KVM_RUN won't do anything as events_{guest,host} of
kvm_pmu_events are still zero).
So, with VHE, enable the guest's EL0 event counting on the first
KVM_RUN (after the migration) when needed. More specifically,
have kvm_pmu_handle_pmcr() call kvm_vcpu_pmu_restore_guest()
so that kvm_pmu_handle_pmcr() on the first KVM_RUN can take
care of it.
Fixes: d0c94c4979 ("KVM: arm64: Restore PMU configuration on first run")
Cc: stable@vger.kernel.org
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Reiji Watanabe <reijiw@google.com>
Link: https://lore.kernel.org/r/20230329023944.2488484-1-reijiw@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e86fc1a3a3 upstream.
We walk the userspace PTs to discover what mapping size was
used there. However, this can race against the userspace tables
being freed, and we end-up in the weeds.
Thankfully, the mm code is being generous and will IPI us when
doing so. So let's implement our part of the bargain and disable
interrupts around the walk. This ensures that nothing terrible
happens during that time.
We still need to handle the removal of the page tables before
the walk. For that, allow get_user_mapping_size() to return an
error, and make sure this error can be propagated all the way
to the the exit handler.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230316174546.3777507-2-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32f86da7c8 upstream.
The WM8960 Linux driver expects the clock to be named "mclk". Otherwise
the clock will be ignored and not prepared/enabled by the driver.
Fixes: 40ba2eda0a ("arm64: dts: imx8mm-nitrogen-r2: add audio")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e68b5517d ]
Running a rt-kernel base on 6.2.0-rc3-rt1 on an Ampere Altra outputs
the following:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 9, name: kworker/u320:0
preempt_count: 2, expected: 0
RCU nest depth: 0, expected: 0
3 locks held by kworker/u320:0/9:
#0: ffff3fff8c27d128 ((wq_completion)efi_rts_wq){+.+.}-{0:0}, at: process_one_work (./include/linux/atomic/atomic-long.h:41)
#1: ffff80000861bdd0 ((work_completion)(&efi_rts_work.work)){+.+.}-{0:0}, at: process_one_work (./include/linux/atomic/atomic-long.h:41)
#2: ffffdf7e1ed3e460 (efi_rt_lock){+.+.}-{3:3}, at: efi_call_rts (drivers/firmware/efi/runtime-wrappers.c:101)
Preemption disabled at:
efi_virtmap_load (./arch/arm64/include/asm/mmu_context.h:248)
CPU: 0 PID: 9 Comm: kworker/u320:0 Tainted: G W 6.2.0-rc3-rt1
Hardware name: WIWYNN Mt.Jade Server System B81.03001.0005/Mt.Jade Motherboard, BIOS 1.08.20220218 (SCP: 1.08.20220218) 2022/02/18
Workqueue: efi_rts_wq efi_call_rts
Call trace:
dump_backtrace (arch/arm64/kernel/stacktrace.c:158)
show_stack (arch/arm64/kernel/stacktrace.c:165)
dump_stack_lvl (lib/dump_stack.c:107 (discriminator 4))
dump_stack (lib/dump_stack.c:114)
__might_resched (kernel/sched/core.c:10134)
rt_spin_lock (kernel/locking/rtmutex.c:1769 (discriminator 4))
efi_call_rts (drivers/firmware/efi/runtime-wrappers.c:101)
[...]
This seems to come from commit ff7a167961 ("arm64: efi: Execute
runtime services from a dedicated stack") which adds a spinlock. This
spinlock is taken through:
efi_call_rts()
\-efi_call_virt()
\-efi_call_virt_pointer()
\-arch_efi_call_virt_setup()
Make 'efi_rt_lock' a raw_spinlock to avoid being preempted.
[ardb: The EFI runtime services are called with a different set of
translation tables, and are permitted to use the SIMD registers.
The context switch code preserves/restores neither, and so EFI
calls must be made with preemption disabled, rather than only
disabling migration.]
Fixes: ff7a167961 ("arm64: efi: Execute runtime services from a dedicated stack")
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Cc: <stable@vger.kernel.org> # v6.1+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 100d9c94cc upstream.
Serdes register space sizes are incorrect, update them to match the
actual sizes from downstream QCA 5.4 kernel.
Fixes: 942bcd33ed ("arm64: dts: qcom: Fix IPQ8074 PCIe PHY nodes")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230113164449.906002-1-robimarko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0ee8e0ba5 ]
A special compatible was introduced for PMK8350 both in the driver and
the bindings to facilitate for 2 base registers (PBS & HLOS). Use it.
Fixes: b2de431360 ("arm64: dts: qcom: pmk8350: Add peripherals for pmk8350")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230213212930.2115182-1-konrad.dybcio@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f46ef374e0 ]
PMK8350 is the first PMIC to require both HLOS and PBS registers for
PON to function properly (at least in theory, sm8350 sees no change).
The support for it on the driver side has been added long ago,
but it has never been wired up. Do so.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221115132626.7465-1-konrad.dybcio@linaro.org
Stable-dep-of: c0ee8e0ba5 ("arm64: dts: qcom: pmk8350: Use the correct PON compatible")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d44106883d ]
The memory region reserved by a previous commit (see fixes tag below)
overlaps with the SMEM and MPSS memory regions, causing error messages in
dmesg:
OF: reserved mem: OVERLAP DETECTED!
reserved@5000000 (0x0000000005000000--0x0000000007200000)
overlaps with smem_region@6a00000
(0x0000000006a00000--0x0000000006c00000)
OF: reserved mem: OVERLAP DETECTED!
reserved@6c00000 (0x0000000006c00000--0x0000000007200000)
overlaps with memory@7000000
(0x0000000007000000--0x000000000ca00000)
This patch resolves both of these by splitting the previously reserved
memory region into two sections either side of the SMEM region and by
cutting off the second memory region to 0x7000000.
Fixes: 22c7e1a0fa ("arm64: dts: msm8992-bullhead: add memory hole region")
Signed-off-by: Jamie Douglass <jamiemdouglass@gmail.com>
Reviewed-by: Petr Vorel <pvorel@suse.cz>
Tested-by: Petr Vorel <pvorel@suse.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230202054819.16079-1-jamiemdouglass@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 160ce54d63 ]
MT8192 features the ARM DynamIQ technology and combines both four
Cortex-A76 (big) and four Cortex-A55 (LITTLE) CPUs in one cluster:
fix the CPU map to reflect that.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Fixes: 48489980e2 ("arm64: dts: Add Mediatek SoC MT8192 and evaluation board dts and Makefile")
Link: https://lore.kernel.org/r/20230126103526.417039-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 856968e066 ]
For proper warm (re)boot from SD card the BPI-M5 board requires TFLASH_VDD_EN
and VDDIO_C pins to be switched to high impedance mode. This can be achieved
using OPEN_DRAIN instead of ACTIVE_HIGH to leave the GPIO pins in input mode
and retain high state (pin has the pull-up).
This change is inspired by meson-sm1-odroid.dtsi where OPEN_DRAIN has been
used to resolve similar problems with the Odroid C4 board (TF_IO in the C4
dts is the equivalent regulator).
Fixes: 976e920183 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Suggested-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230127142221.3718184-2-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7f9492dfc ]
The board used to originally introduce the Beacon Embedded RZ/G2[M/N/H]
boards had a GPIO expander with address 20, but this was changed when
the final board went to production.
The production boards changed both the part itself and the address.
With the incorrect address, the LCD cannot come up. If the LCD fails,
the rcar-du driver fails to come up, and that also breaks HDMI.
Pre-release board were not shipped to the general public, so it should
be safe to push this as a fix. Anyone with a production board would
have video fail due to this GPIO expander change.
Fixes: a1d8a344f1 ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230114225647.227972-1-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d2f14117a ]
Add an active trip tied to the on-board fan cooling device, which is better
than describing it along the passive cooling maps.
Fixes: 33b14f663d ("arm64: dts: meson: add initial device-tree for ODROID-HC4")
Reported-by: Ricardo Pardini <ricardo@pardini.net>
Link: https://lore.kernel.org/r/20230124-topic-odroid-hc4-upstream-fix-fan-trip-v1-1-b0c6aa355d93@linaro.org
Tested-by: Ricardo Pardini <ricardo@pardini.net>
[narmstrong: added Ricardo's tested-by from off-list chat]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cbd431c2b ]
Amlogic G12A devices experience CPU stalls and random board wedges when
the system idles and CPU cores clock down to lower opp points. Recent
vendor kernels include a change to remove 100-250MHz and other distro
sources also remove the 500/667MHz points. Unless all 100-667Mhz opps
are removed or the CPU governor forced to performance stalls are still
observed, so let's remove them to improve stability and uptime.
Fixes: b190056fa9 ("arm64: dts: meson-g12a: add cpus OPP table")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20230119053031.21400-1-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e8b90c025 ]
Current PCIe QMP PHY output name were changed in ("arm64: dts: qcom: Fix
IPQ8074 PCIe PHY nodes") however it did not account for the fact that GCC
driver is relying on the old names to match them as they are being used as
the parent for the gcc_pcie0_pipe_clk and gcc_pcie1_pipe_clk.
This broke parenting as GCC could not find the parent clock, so fix it by
changing to the names that driver is expecting.
Fixes: 942bcd33ed ("arm64: dts: qcom: Fix IPQ8074 PCIe PHY nodes")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230113164449.906002-9-robimarko@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e83a9c41a ]
IPQ8074 comes in 2 silicon versions:
* v1 with 2x Gen2 PCIe ports and QMP PHY-s
* v2 with 1x Gen3 and 1x Gen2 PCIe ports and QMP PHY-s
v2 is the final and production version that is actually supported by the
kernel, however it looks like PCIe related nodes were added for the v1 SoC.
Finish the PCIe fixup by using the correct compatible, adding missing ATU
register space, declaring max-link-speed, use correct ranges, add missing
clocks and resets.
Fixes: 33057e1672 ("ARM: dts: ipq8074: Add pcie nodes")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230113164449.906002-8-robimarko@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ba33591b4 ]
IPQ8074 comes in 2 silicon versions:
* v1 with 2x Gen2 PCIe ports and QMP PHY-s
* v2 with 1x Gen3 and 1x Gen2 PCIe ports and QMP PHY-s
v2 is the final and production version that is actually supported by the
kernel, however it looks like PCIe related nodes were added for the v1 SoC.
Now that we have Gen3 QMP PHY support, we can start fixing the PCIe support
by fixing the Gen3 QMP PHY node first.
Change the compatible to the Gen3 QMP PHY, correct the register space start
and size, add the missing misc PCS register space.
Fixes: 33057e1672 ("ARM: dts: ipq8074: Add pcie nodes")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230113164449.906002-2-robimarko@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed22cc93ab ]
The size of the PCIe PHY serdes register region is 0x1c4 and the
corresponding 'reg' property should specifically not include the
adjacent regions that are defined in the child node (e.g. tx and rx).
Fixes: 33057e1672 ("ARM: dts: ipq8074: Add pcie nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220915143431.19842-1-johan+linaro@kernel.org
Stable-dep-of: 7ba33591b4 ("arm64: dts: qcom: ipq8074: fix Gen3 PCIe QMP PHY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942bcd33ed ]
IPQ8074 PCIe PHY nodes are broken in the many ways:
- '#address-cells', '#size-cells' and 'ranges' are missing.
- Child phy/lane node is missing, and the child properties like
'#phy-cells' and 'clocks' are mistakenly put into parent node.
- The clocks properties for parent node are missing.
Fix them to get the nodes comply with the bindings schema.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210929034253.24570-9-shawn.guo@linaro.org
Stable-dep-of: 7ba33591b4 ("arm64: dts: qcom: ipq8074: fix Gen3 PCIe QMP PHY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 877cff3568 ]
It seems that clock-output-names for the USB3 QMP PHY-s where set without
actually checking what is the GCC clock driver expecting, so clock core
could never actually find the parents for usb0_pipe_clk_src and
usb1_pipe_clk_src clocks in the GCC driver.
So, correct the names to be what the driver expects so that parenting
works.
Before:
gcc_usb0_pipe_clk_src 0 0 0 125000000 0 0 50000 Y
gcc_usb1_pipe_clk_src 0 0 0 125000000 0 0 50000 Y
After:
usb3phy_0_cc_pipe_clk 1 1 0 125000000 0 0 50000 Y
usb0_pipe_clk_src 1 1 0 125000000 0 0 50000 Y
gcc_usb0_pipe_clk 1 1 0 125000000 0 0 50000 Y
usb3phy_1_cc_pipe_clk 1 1 0 125000000 0 0 50000 Y
usb1_pipe_clk_src 1 1 0 125000000 0 0 50000 Y
gcc_usb1_pipe_clk 1 1 0 125000000 0 0 50000 Y
Fixes: 5e09bc51d0 ("arm64: dts: ipq8074: enable USB support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230108130440.670181-2-robimarko@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f189c869ad ]
Node names should be generic and use hyphens instead of underscores to
not cause warnings. Also nodes without a reg property should not have a
unit-address. Change the scpi_dvfs node to use clock-controller as node
name without a unit address (since it does not have a reg property).
Fixes: 70db166a2b ("ARM64: dts: meson-gxbb: Add SCPI with cpufreq & sensors Nodes")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230111211350.1461860-7-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7303651bb ]
Documentation/devicetree/bindings/net/ethernet-phy.yaml defines that the
node name for Ethernet PHYs should match the following pattern:
^ethernet-phy(@[a-f0-9]+)?$
Replace the underscore with a hyphen to adhere to this binding.
Fixes: 280c17df8f ("arm64: dts: meson: g12a: add mdio multiplexer")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230111211350.1461860-6-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ed5310356 ]
Unit names should use hyphens instead of underscores to not cause
warnings.
Fixes: bfe59f92d3 ("ARM64: dts: amlogic: gxbb: Enable NVMEM")
Suggested-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230111211350.1461860-5-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 740862bb5f ]
The pin config entry should have a string, not number, for the GPIO used
as WCD9340 audio codec interrupt.
Fixes: 89a32a4e76 ("arm64: dts: qcom: db845c: add analog audio support")
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221222151319.122398-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce8a06b5ba ]
The systimer block derives its 13 MHz clock by dividing the main 26 MHz
oscillator clock by 2 internally, not through the TOPCKGEN clock
controller.
On the MT8183 this divider is set either by power-on-reset or by the
bootloader. The bootloader may then make the divider unconfigurable to,
but can be read out by, the operating system.
Making the systimer block take the 26 MHz clock directly requires
changing the implementations. As an ABI compatible fix, change the
input clock of the systimer block a fixed factor divide-by-2 clock
that takes the 26 MHz oscillator as its input.
Fixes: 5bc8e2875f ("arm64: dts: mt8183: add systimer0 device node")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221201084229.3464449-2-wenst@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8416262b0e ]
Reorder the clocks and corresponding names to match the QUSB2 phy
schema, fixing the following CHECK_DTBS errors:
arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dtb: phy@1613000: clock-names:0: 'cfg_ahb' was expected
From schema: /newdata/aosp-r/kernel/mainline/kernel/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml
arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dtb: phy@1613000: clock-names:1: 'ref' was expected
From schema: /newdata/aosp-r/kernel/mainline/kernel/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml
Fixes: cff4bbaf2a ("arm64: dts: qcom: Add support for SM6125")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221216213343.1140143-1-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be8de06dc3 ]
The framebuffer configuration for kumano griffin, written in kumano dtsi
(which is overwritten in bahamut dts for its smaller panel) has to use a
1096x2560 configuration as this is what the panel (and framebuffer area)
has been initialized to. Downstream userspace also has access to (and
uses) this 2.5k mode by default, and only switches the panel to 4k when
requested.
Fixes: d0a6ce59ea ("arm64: dts: qcom: sm8150: Add support for SONY Xperia 1 / 5 (Kumano platform)")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209191733.1458031-1-marijn.suijten@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43069b9cd3 ]
The hardware turns out to be pretty sluggish at assuming it can only
do USB2 with just a USB2 phy assigned to it - before it needed about
6 minutes to acknowledge that.
Limit it to USB-HS explicitly to make USB come up about 720x faster.
Fixes: 9da65e441d ("arm64: dts: qcom: Add support for SONY Xperia X Performance / XZ / XZs (msm8996, Tone platform)")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221124220147.102611-1-konrad.dybcio@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41a37d157a ]
The commit e5bbbff5b7 ("clk: gcc-qcs404: Add PCIe resets") added names
for PCIe resets, but it did not change the existing qcs404.dtsi to use
these names. Do it now and use symbol names to make it easier to check
and modify the dtsi in future.
Fixes: e5bbbff5b7 ("clk: gcc-qcs404: Add PCIe resets")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221226042154.2666748-14-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1692bffec6 ]
GPIO LEDs do not have a 'mode' property:
rockchip/rk3328-roc-pc.dtb: leds: led-0: Unevaluated properties are not allowed ('mode' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221125144135.477144-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c89bb8e32 ]
This clean up the error/notification messages in kprobes related code.
Basically this defines 'pr_fmt()' macros for each files and update
the messages which describes
- what happened,
- what is the kernel going to do or not do,
- is the kernel fine,
- what can the user do about it.
Also, if the message is not needed (e.g. the function returns unique
error code, or other error message is already shown.) remove it,
and replace the message with WARN_*() macros if suitable.
Link: https://lkml.kernel.org/r/163163036568.489837.14085396178727185469.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Stable-dep-of: eb7423273c ("riscv: kprobe: Fixup misaligned load text")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d182bcf300 upstream.
The usage of edge-triggered interrupts lead to lost interrupts under load,
see [0]. This was confirmed to be fixed by using level-triggered
interrupts.
The report was about SDIO. However, as the host controller is the same
for SD and MMC, apply the change to all mmc controller instances.
[0] https://www.spinics.net/lists/linux-mmc/msg73991.html
Fixes: 221cf34bac ("ARM64: dts: meson-axg: enable the eMMC controller")
Reported-by: Peter Suti <peter.suti@streamunlimited.com>
Tested-by: Vyacheslav Bocharov <adeep@lexina.in>
Tested-by: Peter Suti <peter.suti@streamunlimited.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/c00655d3-02f8-6f5f-4239-ca2412420cad@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjorn Andersson
Yassine Oudjana
Krzysztof Kozlowski
Robert Marko
Marc Zyngier
Adam Ford
Shenwei Wang
Douglas Anderson
Linus Walleij
Min-Hua Chen
Hugo Villeneuve
Peter Collingbourne
Konrad Dybcio
Vincent Guittot
Sumit Garg
Manivannan Sadhasivam
Dmitry Baryshkov
Rafał Miłecki
William Zhang
Anand Gore
Bhavya Kapoor
Geert Uytterhoeven
Ard Biesheuvel
Dan Carpenter
David Matlack
Peng Fan
Marc Gonzalez
Reiji Watanabe
Marek Vasut
Pierre Gondois
Robert Marko
Jamie Douglass
AngeloGioacchino Del Regno
Christian Hewitt
Neil Armstrong
Vaishnav Achath
Johan Hovold
Shawn Guo
Petr Vorel
Dominik Kobinski
Martin Blumenstingl
Chen-Yu Tsai
Marijn Suijten
Masami Hiramatsu
Heiner Kallweit