This driver USE PLL for 11025/22050/44100/88200 rate.
To enable switching to bypass mode, PLL is always turned on.
Special thanks to Phil
Signed-off-by: Phil Edworthy <Phil.Edworthy@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Towards having build for multiple SoCs segregate hw_params callback
for s3c2412 and s3c64xx.
Since, all new SoCs have s3c64xx like register map, we keep that as
default implementation if no SoC specific callback is already defined.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For some CPU-CODEC and source clock combination we might need to set
BCLK to N*Sample_size*LRCLK, where N may be even 3 or 4, not just 2.
We can simply remove the dependency of BCLK on sample size as there
is already a callback(S3C_I2SV2_DIV_BCLK) available to set required BCLK.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Towards generalizing CPU driver interface, do not accept direct field
values for the BCLK and RCLK.
The machine driver should simply request the FS-multiple and not provide
the value to be set in divide field of IISMOD.
[Confirmed by Jassi that no existing machine drivers are affected --
broonie]
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order for the RATE and FMT defines to be reuseable in future by the
i2sv4 driver, move the MACROs out to the header file.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having the multiple definitions of the same clocks,
define them in one common place and refer by SoC specific names.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No point in duplicating this structure layout in each driver.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On TI DM6467 EVM, S/PDIF DIT codec fails to open as it is unable to install
hardware params. This dummy codec has no set_fmt and set_sysclk implementations
and calls from the application to these functions cause errors. This patch adds
a new hardware params callback function for S/PDIF transciever codec.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (62 commits)
msi-laptop: depends on RFKILL
msi-laptop: Detect 3G device exists by standard ec command
msi-laptop: Add resume method for set the SCM load again
msi-laptop: Support some MSI 3G netbook that is need load SCM
msi-laptop: Add threeg sysfs file for support query 3G state by standard 66/62 ec command
msi-laptop: Support standard ec 66/62 command on MSI notebook and nebook
Driver core: create lock/unlock functions for struct device
sysfs: fix for thinko with sysfs_bin_attr_init()
sysfs: Kill unused sysfs_sb variable.
sysfs: Pass super_block to sysfs_get_inode
driver core: Use sysfs_rename_link in device_rename
sysfs: Implement sysfs_rename_link
sysfs: Pack sysfs_dirent more tightly.
sysfs: Serialize updates to the vfs inode
sysfs: windfarm: init sysfs attributes
sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on module dynamic attributes
sysfs: Document sysfs_attr_init and sysfs_bin_attr_init
sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on dynamic attributes
sysfs: Use one lockdep class per sysfs attribute.
sysfs: Only take active references on attributes.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (26 commits)
ALSA: hdmi - show debug message on changing audio infoframe
ALSA: hdmi - merge common code for intelhdmi and nvhdmi
ALSA: hda - Add ASRock mobo to MSI blacklist
ALSA: hda: uninitialized variable fix
ALSA: hda: Use LPIB for a Biostar Microtech board
ALSA: usb/audio.h: Fix field order
ALSA: fix jazz16 compile (udelay)
ALSA: hda: Use LPIB for Dell Latitude 131L
ALSA: hda - Build hda_eld into snd-hda-codec module
ALSA: hda - Support NVIDIA MCP89 and GT21x hdmi audio
ALSA: hda - Support max codecs to 8 for nvidia hda controller
ALSA: riptide: clean up while loop
ALSA: usbaudio - remove debug "SAMPLE BYTES" printk line
ALSA: timer - pass real event in snd_timer_notify1() to instance callback
ALSA: oxygen: change || to &&
ALSA: opti92x: use PnP data to select Master Control port
ASoC: fix ak4104 register array access
ASoC: soc_pcm_open: Add missing bailout tag
ALSA: usbaudio: Fix wrong bitrate for Creative Creative VF0470 Live Cam
ALSA: ua101: removing debugging code
...
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] smsgiucv_app: deliver z/VM CP special messages (SMSG) as uevents
[S390] smsgiucv: declare char pointers as "const"
[S390] dasd: automatic recognition of read-only devices
[S390] remove unused qdio flags in zfcp and qeth
[S390] Cleanup xtime usage
[S390] qdio: add missing bracket
[S390] cio: fix init_count in case of recognition after steal lock
[S390] dasd: security and PSF update patch for EMC CKD ioctl
[S390] hvc_iucv: allocate memory buffers for IUCV in zone DMA
[S390] uaccess: make sure copy_from_user_overflow is builtin
Remove the EXPERIMENTAL flag from FS-Cache so that Ubuntu can make use of the
facility.
Signed-off-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the intel 6300esb platform uses a dedicated PCI ID for
it's watchdog timer (00:1d.4), it's better and easier to have
this as a pci_driver.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The smsgiucv_app driver registers a callback with the smsgiucv driver
to receive z/VM CP special messages (SMSG) starting with "APP".
When the callback is called for special messages, the driver creates
an uevent for the received message. The uevent consists of additional
environment data containing the message prefix ("APP"), message sender,
and message content.
udev rules can be used to trigger application specific actions through
matching the content or sender of the special message.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Declare the smsgiucv prefix char pointer as "const" and use
use const char pointers in callback functions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In z/VM it is possible to attach a device as read-only. To prevent
unintentional write requests and subsequent I/O errors, we can detect
this configuration using the z/VM DIAG 210 interface and set the
respective linux block device to read-only as well.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
zfcp and qeth are setting flags for the qdio-layer, but these flags
are not used in qdio. Patch removes the flag definitions from qdio
and their settings in zfcp and qeth.
Cc: Jan Glauber <jang@linux.vnet.ibm.com>
Cc: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This replaces direct xtime usage in the s390 arch with timekeeping accessors,
so we can further clean up the timekeeping core.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a missing bracket to only log the outbound handler event in the
appropriate case.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After we try to steal a lock on a ccw device in boxed state,
we have to restart device recognition and potentially reprobing.
In this case ccw_device_init_count was erroneously decreased
twice. This patch fixes the issue.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the PSF order/suborder check from the Symmetrix CKD dasd ioctl.
In exchange restrict the ioctl to CAP_SYS_ADMIN and CAP_SYS_RAWIO.
Signed-off-by: Nigel Hislop <hislop_nigel@emc.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The device driver must allocate memory for IUCV buffers with GFP_DMA,
because IUCV cannot address memory above 2GB (31bit addresses only).
Because the IUCV ignores the higher bits of the address, sending and
receiving IUCV data with this driver might cause memory corruptions.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If there is no in kernel image caller modules will suffer:
ERROR: "copy_from_user_overflow" [net/core/pktgen.ko] undefined!
ERROR: "copy_from_user_overflow" [net/can/can-raw.ko] undefined!
ERROR: "copy_from_user_overflow" [fs/cifs/cifs.ko] undefined!
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Before you can read or write from the i6300esb memeory mapped registers,
you need to unlock these. This is done by writing the magic numbers 0x80
and 0x86 to the reload register. The size of the reload register is 32bit
though.
Also binary 11 is hex 0x03 and not 0x11.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Create patch_hdmi.c to hold common code from intelhdmi and nvhdmi.
For now the patch_hdmi.c file is simply included by patch_intelhdmi.c
and patch_nvhdmi.c, and does not represent a real codec.
There are no behavior changes to intelhdmi. However nvhdmi made several
changes when copying code out of intelhdmi, which are all reverted in
this patch. Wei Ni confirmed that the reverted code actually works fine.
Tested-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
msi-laptop uses rfkill*() interfaces so it should depend on RFKILL.
msi-laptop.c:(.text+0x1fcd1b): undefined reference to `rfkill_alloc'
msi-laptop.c:(.text+0x1fcd76): undefined reference to `rfkill_register'
msi-laptop.c:(.text+0x1fcdc8): undefined reference to `rfkill_destroy'
msi-laptop.c:(.text+0x1fcdd9): undefined reference to `rfkill_unregister'
This repairs "msi-laptop: Detect 3G device exists by standard ec command",
which is in some gregkh tree.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Cc: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Detect 3G device exists by standard ec command. Driver will not create the threeg sysfs
file and threeg rfkill interface if there have no internal 3G device in MSI notebook/netbook.
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implement the resume method for set the load SCM flag after system reusme.
Without this patch, the wifi function key on SCM model will back to BIOS
control mode then confuse with the userland software control.
e.g. MSI N034
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some MSI 3G netbook only have one fn key to control Wlan/Bluetooth/3G,
those netbook will load the SCM (windows app) to disable the original
Wlan/Bluetooth control by BIOS when user press fn key, then control
Wlan/Bluetooth/3G by SCM (software control by OS). Without SCM, user
cann't on/off 3G module on those 3G netbook.
On Linux, msi-laptop driver will do the same thing to disable the
original BIOS control, then might need use HAL or other userland
application to do the software control that simulate with SCM.
e.g. MSI N034 netbook
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add threeg sysfs file for support query 3G state by standard 66/62 ec
command, the MSI standard ec interface supported this feature.
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Suppport standard ec 66/62 command on MSI notebook and nebook. MSI
netbook and notebook already support 66/62 command, so, add new
get_state function, and put the old model to non-standard model, but
driver still support those old model.
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Cc: Lennart Poettering <mzxreary@0pointer.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the future, we are going to be changing the lock type for struct
device (once we get the lockdep infrastructure properly worked out) To
make that changeover easier, and to possibly burry the lock in a
different part of struct device, let's create some functions to lock and
unlock a device so that no out-of-core code needs to be changed in the
future.
This patch creates the device_lock/unlock/trylock() functions, and
converts all in-tree users to them.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alex Chiang <achiang@hp.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: CHENG Renquan <rqcheng@smu.edu.sg>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After merging the final tree, today's linux-next build (powerpc
allyesconfig) failed like this:
drivers/pci/pci-sysfs.c: In function 'pci_create_legacy_files':
drivers/pci/pci-sysfs.c:645: error: lvalue required as unary '&' operand
drivers/pci/pci-sysfs.c:658: error: lvalue required as unary '&' operand
Caused by commit "sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on
dynamic attributes" interacting with commit "sysfs: Use one lockdep
class per sysfs attribute") both from the driver-core tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that there are no more users we can remove
the sysfs_sb variable.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently sysfs_get_inode magically returns an inode on
sysfs_sb. Make the super_block parameter explicit and
the code becomes clearer.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't open code the renaming of symlinks in sysfs
instead use the new helper function sysfs_rename_link
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because of rename ordering problems we occassionally give false
warnings about invalid sysfs operations. So using sysfs_rename
create a sysfs_rename_link function that doesn't need strange
workarounds.
Cc: Benjamin Thery <benjamin.thery@bull.net>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Placing the 16bit s_mode between a pointer and a long doesn't pack well
especailly on 64bit where we wast 48 bits. So move s_mode and
declare it as a unsigned short. This is the sysfs backing store
after all we don't need fields extra large just in case someday
we want userspace to be able to use a larger value.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kuninori Morimoto
Jassi Brar
Mark Brown
Barry Song
Cliff Cai
Chaithrika U S
Linus Torvalds
Christian Kujau
Wim Van Sebroeck
Hendrik Brueckner
Stefan Weinhuber
Ursula Braun
John Stultz
Sebastian Ott
Nigel Hislop
Heiko Carstens
Takashi Iwai
Wu Fengguang
Randy Dunlap
Lee, Chun-Yi
Greg Kroah-Hartman
Stephen Rothwell
Eric W. Biederman
Eric W. Biederman