We tried to implement interruptible waiting with timeout (it was broken
anyway) which was not a good idea as explained by Andrew. It's possible
to avoid using additional variable but actually it inroduces using more
complex in-kernel tools. So simply add one variable for condition.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R6xx+ cards need to use the 3D engine to blit data which requires
quite a bit of hw state setup. Rather than pull the whole 3D driver
(which normally generates the 3D state) into the DRM, we opt to use
statically generated state tables. The regsiter state and shaders
were hand generated to support blitting functionality. See the 3D
driver or documentation for descriptions of the registers and
shader instructions.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We still have many magic numbers in HDMI/audio to define
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Older GPUs are little different, HDMI blocks are not hard-wired, but routable.
We should just find some free HDMI block and route it to choosen encoder. In
case of RS6x0 there is only one HDMI block, we don't enable HDMI on RS6x00 yet
however.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We almost always used first HDMI block for first encoder and second for sencod.
Exception was KLDSCP_LVTMA. Analyzing code picking DIG encoder shows the same
behaviour. It shows HDMI block are related to DIGs, which relation we now use.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We already know same offsets are used for different encoders/transmitters, so
just numeric them instead naming incorrectly. Additionaly we found additional
registers needed for RV770+
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
fixing the i2c prescale in the last patch
gets it working on r1xx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
use the i2c pads to drive SDA
Possible fix for fdo bug 26430
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on ddx patch by Andrzej Hajda.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Adjust modeset ordering to fix spread spectrum.
The spread spectrum command table relies on the
crtc routing to already be set in order to work
properly on some asics.
Should fix fdo bug 25741.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The bios has alternate pll output limits for LCD panels.
If available, use these for pll divider calculations.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The atom spread spectrum table does not always
disable ss. Explicitly disable it and then use
the atom table to enable later if needed (currently
only used for LVDS).
Fixes display issues on some systems.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Intended to be used as a workaround in cases where we falsely detect
that a TV is connected when it's not.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
VRAM->system is a synchronous operation: it involves scheduling a
VRAM->TT DMA transfer and stalling the CPU until it's finished so that
we can unbind the new memory from the translation tables. VRAM->TT can
always be performed asynchronously, even if TT is already full and we
have to move something out of it.
Additionally, allowing VRAM->system behaves badly under heavy memory
pressure because once we run out of TT, stuff starts to be moved back
and forth between VRAM and system, and the TT contents are hardly
renewed.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
In somecase the atombios code might lead to infinite loop because
the GPU is in broken state, this patch track the jump history and
will abort atombios execution if we are stuck executing the same
jump for more than 1sec. Note that otherwise in some case we might
enter an infinite loop in the kernel context which is bad.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
The connector table index in the DCB entry for each output type is an
index into the connector table, and does *not* necessarily match up
with what was previously called "index" in the connector table entries
themselves.
Not real sure what that index is exactly, renamed to "index2" as we
still use it to prevent creating multiple TV connectors.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- This is useful for vram pushbuffers that are write combined.
- pre-nv50 has one too (in WRITE_PUT).
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- In case of suspend lockups it's nice to know it happened in nouveau.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The calculated values were a little bit off (~16 clocks), the only
effect it could have had is a slightly offset image with respect to
the blob on analog outputs (bug 26790).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This makes nouveau recognise and report more kinds of PGRAPH errors, as
well as prevent GPU lockups resulting from some of them.
Lots of guesswork was involved and some part of this is probably
incorrect. Some potential-lockuop situations are handled by just
resetting a whole PGRAPH subunit, which doesn't sound like a "proper"
solution, but seems to work just fine... for now.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will fix races between generated ctxprogs and interrupt handler.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
NV50 is nice and has a switch that autoaligns stuff for us. Pre-NV50,
we need to align input bitmap width manually.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
11c/004 offset corresponds to PGRAPH reg 0x400828, and is initialised
earlier anyway by both our ctxprog generator and blob ctxvals. It's
actually incorrect with the generator, since we use different layout
on pre-NVA0.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert some drivers who export a single string as class attribute
to the new class_attr_string functions. This removes redundant
code all over.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.
Also drivers can extend the attributes with own data fields
and use that in the low level function.
This makes the class attributes the same as sysdev_class attributes
and plain attributes.
This will allow further cleanups in drivers.
Full tree sweep converting all users.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit a069c266ae.
It turns ou that not only was it missing a case (XFS) that needed it,
but perhaps more importantly, people sometimes want to enable new
modules that they hadn't had enabled before, and if such a module uses
list_sort(), it can't easily be inserted any more.
So rather than add a "select LIST_SORT" to the XFS case, just leave it
compiled in. It's not all _that_ big, after all, and the inconvenience
isn't worth it.
Requested-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Don Mullis <don.mullis@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Build list_sort() only for configs that need it -- those that don't save
~581 bytes (i386).
Signed-off-by: Don Mullis <don.mullis@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (151 commits)
vga_switcheroo: disable default y by new rules.
drm/nouveau: fix *staging* driver build with switcheroo off.
drm/radeon: fix typo in Makefile
vga_switcheroo: fix build on platforms with no ACPI
drm/radeon: Fix printf type warning in 64bit system.
drm/radeon/kms: bump the KMS version number for square tiling support.
vga_switcheroo: initial implementation (v15)
drm/radeon/kms: do not disable audio engine twice
Revert "drm/radeon/kms: disable HDMI audio for now on rv710/rv730"
drm/radeon/kms: do not preset audio stuff and start timer when not using audio
drm/radeon: r100/r200 ums: block ability for userspace app to trash 0 page and beyond
drm/ttm: fix function prototype to match implementation
drm/radeon: use ALIGN instead of open coding it
drm/radeon/kms: initialize set_surface_reg reg for rs600 asic
drm/i915: Use a dmi quirk to skip a broken SDVO TV output.
drm/i915: enable/disable LVDS port at DPMS time
drm/i915: check for multiple write domains in pin_and_relocate
drm/i915: clean-up i915_gem_flush_gpu_write_domain
drm/i915: reuse i915_gpu_idle helper
drm/i915: ensure lru ordering of fence_list
...
Fixed trivial conflicts in drivers/gpu/vga/Kconfig
radeon was always including the atpx code unnecessarily, also core
switcheroo was including acpi headers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Type of iterator was promoted to unsigned long in 64bit systems.
*header is small structure so it is alwas safe to cast return value
of sizeof operator to int.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.
4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia - - use _DSM ACPI method.
TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.
v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.
v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.
v4: ATPX msg handling using buffers - should work on more machines
v5: rearchitect after more mjg59 discussion - move ATPX handling to
radeon driver.
v6: add file headers + initial nouveau bits (to be filled out).
v7: merge delayed switcher code.
v8: avoid suspend/resume of gpu that is off
v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling
v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv
v11: fix bug in resuming Intel for 2nd time.
v12: start fixing up nvidia code blindly.
v13: blindly guess at finishing nvidia code
v14: remove radeon audio hacks - fix up intel resume more like upstream
v15: clean up printks + remove unnecessary igd/dis pointers
mount debugfs
/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
+ 2 cards.
DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use
Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit "disabled" audio on RV710 and RV740 only, leaving RV770 and RV730.
The order is: CHIP_RV770 < CHIP_RV730 < CHIP_RV710 < CHIP_RV740.
It is not needed anway, as we do not even try to enable audio on RV770 and
newer. We call initializing function in r600.c only, not in rv770.c.
If there is something causing green tinges, it's HDMI mode setting for encoder
and I will try to debug that.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-testing' of /ssd/git/drm-radeon-next:
drm/radeon: r100/r200 ums: block ability for userspace app to trash 0 page and beyond
drm/ttm: fix function prototype to match implementation
drm/radeon: use ALIGN instead of open coding it
drm/radeon/kms: initialize set_surface_reg reg for rs600 asic
radeon's have a special ability to passthrough writes in their internal
memory space directly to PCI, this ability means that if some of the internal
surfaces like the depth buffer point at 0x0, any writes to these will
go directly to RAM at 0x0 via PCI busmastering.
Now mesa used to always emit clears after emitting state, since the
radeon mesa driver was refactored a year or more ago, it was found it
could generate a clear request without ever sending any setup state to the
card. So the clear would attempt to clear the depth buffer at 0x0, which
would overwrite main memory at this point. fs corruption ensues.
Also once one app did this correctly, it would never get set back to 0
making this messy to reproduce.
The kernel should block this from happening as mesa runs without privs,
though it does require the user be connected to the current running X session.
This patch implements a check to make sure the depth offset has been set
before a depth clear occurs and if it finds one it prints a warning and
ignores the depth clear request. There is also a mesa fix to avoid sending
the badness going into mesa.
This only affects r100/r200 GPUs in user modesetting mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 asic was missing set_surface_reg callback leading to
oops.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* anholt/drm-intel-next: (103 commits)
drm/i915: Use a dmi quirk to skip a broken SDVO TV output.
drm/i915: enable/disable LVDS port at DPMS time
drm/i915: check for multiple write domains in pin_and_relocate
drm/i915: clean-up i915_gem_flush_gpu_write_domain
drm/i915: reuse i915_gpu_idle helper
drm/i915: ensure lru ordering of fence_list
drm/i915: extract fence stealing code
drm/i915: fixup active list locking in object_unbind
drm/i915: reuse i915_gem_object_put_fence_reg for fence stealing code
drm/i915: Add dependency on the intel agp module
drm/i915: More s/IS_IRONLAKE/HAS_PCH_SPLIT for Sandybridge.
drm/i915: Correct the Sandybridge chipset info structs.
drm/i915: Disable the hangcheck reset on Sandybridge until we add support.
drm/i915: Add a new mobile Sandybridge PCI ID.
agp/intel: Add a new Sandybridge HB/IG PCI ID combo.
drm/i915, agp/intel: Fix stolen memory size on Sandybridge
drm/i915: Correct locking in the modesetting failure path, fixing a BUG_ON.
drm/i915: Disable the surface tile swizzling on Sandybridge.
agp/intel: Use a non-reserved value for the cache field of the PTEs.
drm/i915: Fix sandybridge status page setup.
...
* nouveau/for-airlied: (25 commits)
drm/nouveau: use ALIGN instead of open coding it
drm/nouveau: report unknown connector state if lid closed
drm/nouveau: support version 0x20 displayport tables
drm/nouveau: Fix noaccel/nofbaccel option descriptions.
drm/nv50: Implement ctxprog/state generation.
drm/nouveau: use dcb connector types throughout the driver
drm/nv50: enable hpd on any connector we know the gpio line for
drm/nouveau: use dcb connector table for creating drm connectors
drm/nouveau: construct a connector table for cards that lack a real one
drm/nouveau: check for known dcb connector types
drm/nouveau: parse dcb gpio/connector tables after encoders
drm/nouveau: reorganise bios header, add dcb connector type enums
drm/nouveau: merge nvbios and nouveau_bios_info
drm/nouveau: merge parsed_dcb and bios_parsed_dcb into dcb_table
drm/nouveau: rename parsed_dcb_gpio to dcb_gpio_table
drm/nouveau: allow retrieval of vbios image from debugfs
drm/nouveau: fix missing spin_unlock in failure path
drm/nouveau: fix i2ctable bounds checking
drm/nouveau: fix nouveau_i2c_find bounds checking
drm/nouveau: fix pramdac_table range checking
...
Conflicts:
drivers/gpu/drm/nouveau/nouveau_gem.c
This IBM system has a multi-function SDVO card that reports both VGA
and TV, but the system has no TV connector. The TV connector always
reported as connected, which would lead to poor modesetting choices.
https://bugs.freedesktop.org/show_bug.cgi?id=25787
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Vance <liangghv@sg.ibm.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
It would be good to disable the LVDS port when we shut down the panel
to save power. We haven't done so until now because we had trouble
getting the right LVDS parameters from the BIOS. I think we're past
that now, so enabling and disabling the port should be safe, though it
would probably be made cleaner with some additional changes to the
display code, where we also bang on the LVDS reg to set the pairing
correctly etc.
Seems to save a bit of power (up to 300mW in my basic wattsup
meter testing).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The assumption that an object has only ever one write domain is deeply
threaded into gem (it's even encoded the the singular of the variable
name). Don't let userspace screw us over.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Now that we have an exact gpu write domain tracking, we don't need
to move objects to the active list ourself. i915_add_request will
take care of that under all circumstances.
Idea stolen from a patch by Chris Wilson <chris@chris-wilson.co.uk>.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
We have it, so use it. This required moving the function to avoid
a forward declaration.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
The fence_list should be lru ordered for otherwise we might try
to steal a fence reg from an active object even though there are
fences from inactive objects available. lru ordering was obeyed
for gpu access everywhere save when moving dirty objects from
flushing_list to active_list.
Fixing this cause the code to indent way to much, so I've extracted
the flushing_list processing logic into its on function.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The spaghetti logic in there tripped up my brain's code parser for a
few secs. Prevent this from happening again by extracting the fence
stealing code into a seperate functions. IMHO this slightly clears up
the code flow.
v2: Beautified according to ickle's comments.
v3: ickle forgot to flush his comment queue ... Now there's also a
we-are-paranoid BUG_ON in there.
v4: I've forgotten to switch on my brain when doing v3. Now the BUG_ON
actually checks something useful.
v5: Clean up a stale comment as noted by Eric Anholt.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
All other accesses take this spinlock, so do this here, too.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
This has a few functional changes against the old code:
* a few more unnecessary loads and stores to the drm_i915_fence_reg
objects. Also an unnecessary store to the hw fence register.
* zaps any userspace mappings before doing other flushes. Only changes
anything when userspace does racy stuff against itself.
* also flush GTT domain. This is a noop, but still try to keep the
bookkeeping correct.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
See http://bugzilla.kernel.org/show_bug.cgi?id=15021
Make sure that the appropriate AGP module is loaded and probed before
trying to set up the DRM. The DRM already depends on the AGP core,
but in this case we know the specific AGP driver we need too, and can
help users avoid the trap of loading the AGP driver after the DRM
driver.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
New memory control config reg at 0x50 should be used for stolen
memory size detection on Sandybridge.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
This is in preference to disconnected. If there's no other outputs
connected this will cause LVDS to be programmed even with the lid
closed rather than having X fail to start because of no available
outputs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not entirely identical to 0x21, the per-encoder table header lacks the
third init table pointer. However, our current parsing of the table
should work just fine.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This removes dependence on external firmware for NV50 generation cards.
If the generated ctxprogs don't work for you for some reason, please
report it.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This makes this code common to both the nv04 and nv50 paths.
For the moment, we keep the previous behaviour with HDMI/eDP connectors
and report them as DVI-D/DP instead. This will be fixed once the rest
of the code has been fixed to deal with those types.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Found by sparse.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
i2c_entries seems to be the number of i2c entries,
so with index equal to this number, we could read
invalid data from i2ctable. Fix it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
get_tmds_index_reg reads some value from stack when mlv happens
to be equal to size of pramdac_table array. Fix it.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This commit breaks the userspace interface, and requires a new libdrm for
nouveau to operate again.
The multiple GEM_PUSHBUF ioctls that were present in 0.0.15 for
compatibility purposes are now gone, and replaced with the new ioctl which
allows for multiple push buffers to be submitted (necessary for hw index
buffers in the nv50 3d driver) and relocations to be applied on any buffer.
A number of other ioctls (CARD_INIT, GEM_PIN, GEM_UNPIN) that were needed
for userspace modesetting have also been removed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
This allows us to submit push buffers from any memtype to the hardware.
We'll need this ability for VRAM index buffers at some point.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
PFIFO on G80 and up has a new mode where the main ring buffer is simply a
ring of pointers to indirect buffers containing the actual command/data
packets. In order to be able to implement index buffers in the 3D driver
we need to be able to submit data-only push buffers right after the cmd
packet header, which is only possible using the new command submission
method.
This commit doesn't make it possible to implement index buffers yet, some
userspace interface changes will be required, but it does allow for
testing/debugging of the hardware-side support in the meantime.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The nv50 pgraph handler (for example) could reenable pgraph fifo access
and that would be bad when pgraph context is being unloaded (we need the
guarantee a ctxprog isn't running).
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
* anholt/drm-intel-next:
drm/i915: Record batch buffer following GPU error
drm/i915: give up on 8xx lid status
drm/i915: reduce some of the duplication of tiling checking
drm/i915: blow away userspace mappings before fence change
drm/i915: move a gtt flush to the correct place
agp/intel: official names for Pineview and Ironlake
drm/i915: overlay: drop superflous gpu flushes
drm/i915: overlay: nuke readback to flush wc caches
drm/i915: provide self-refresh status in debugfs
drm/i915: provide FBC status in debugfs
drm/i915: fix drps disable so unload & re-load works
drm/i915: Fix OGLC performance regression on 945
drm/i915: Deobfuscate the render p-state obfuscation
drm/i915: add dynamic performance control support for Ironlake
drm/i915: enable memory self refresh on 9xx
drm/i915: Don't reserve compatibility fence regs in KMS mode.
drm/i915: Keep MCHBAR always enabled
drm/i915: Replace open-coded eviction in i915_gem_idle()
- Without this change I get a general protection fault.
- Also use PTR_ERR where applicable.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The whole attribute table is valid for
shr/shl ops.
Fixes fdo bug 26668
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
- add support for pre-avivo chips
- add support for fixed post/ref dividers
- add support for non-fractional fb dividers
By default avivo chips use the new algo and
pre-avivo chips use the old algo. Use the "new_pll"
module option to toggle between them.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch properly set visible VRAM and enforce any pinned buffer
to be into visible VRAM. We might later add a flag to release this
constraint for some newer hw more clever than previous.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/vmwgfx: Fix queries if no dma buffer thrashing is occuring.
drm/nv50: fix vram ptes on IGPs to point at stolen system memory
drm/nv50: fix instmem binding on IGPs to point at stolen system memory
drm/nv50: improve vram page table construction
drm/nv50: more efficient clearing of gpu page table entries
drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
drm/nouveau: Fix up pre-nv17 analog load detection.
Intercept query commands and apply relocations to their guest pointers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'nouveau/for-airlied' of ../drm-nouveau-next:
drm/nv50: fix vram ptes on IGPs to point at stolen system memory
drm/nv50: fix instmem binding on IGPs to point at stolen system memory
drm/nv50: improve vram page table construction
drm/nv50: more efficient clearing of gpu page table entries
drm/nv50: make nv50_mem_vm_{bind,unbind} operate only on vram
drm/nouveau: Fix up pre-nv17 analog load detection.
This also modifies the unused PRAMIN PT entries to be all zeroes, can't
really recall why I used 9/0 initially, just that it didn't work for
some reason. It was likely masking a bug elsewhere that's since been
fixed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This commit changes nouveau to construct PTEs which look very much like
the ones the binary driver creates.
I presume that filling multiple PTEs identically with length flags and
the physical address of the start of a block of VRAM is a hint to the
memory controller that it need not perform additional page table lookups
for that range of addresses.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
AtomBIOS tables on non-mobility GPU do not contain POWERSAVE/BATTERY.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We kept pointers to requested and current clock modes in every power state.
That was useless, more /global/ pointers in power struct are enough.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- updated swizzle modes for backend map setup
- fix programming of a few gfx regs
- properly handle pipe/backend setup on LE cards
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Version 2 of memory controller did break the initialization for
R3XX/R4XX hardware. This patch fix it.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds a check on avivo chips to see if we are in the VBL
region for the active crtcs when we trigger the engine change.
I appear to have glitches locally on pm transistion (not sure all
fixes are in yet) and this at least seems to be correct here,
maybe others can test on systems with no glitches.
Allocation of single large block of memory may fail under memory
presure. drm_buffer object can hold one large block of data in
multiple independ pages which preents alloation failures.
This patch converts all access to command stream to use drm_buffer
interface. All direct access to array has to go tough drm_buffer
functions to get correct pointer.
Outputting the command stream to ring buffer needs to be awear of
the split nature of drm_buffer. The output operation requires the
new OUT_RING_DRM_BUFFER.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Allocating multiple pages of memory for data that is coming
from user space may fail. To fix memory allocation failures
the buffer object should be split to multiple independ pages.
drm buffer provides generic interface to copy and process
large data arrays from user space.
Interface includes allocation and free functions to allocate
the buffer object and data storage pages.
All access operations are performed relative to a internal
pointer which is advanced with drm_buffer_advance function.
The buffer can be accessed using drm_buffer_pointer_to_XXX
functions if it is known that requested object doesn't split
over a page boundary. These functions don't do any error
checking to maximize performance.
If there is large object which could be split there is special
drm_buffer_read_object function. drm_buffer_read_object takes
a pointer as argument which is used as temporary store for
data if it is split over boundary in the buffer.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In order to improve our diagnostic capabilities following a GPU hang
and subsequent reset, we need to record the batch buffer that triggered
the error. We assume that the current batch buffer, plus a few details
about what else is on the active list, will be sufficient -- at the very
least an improvement over nothing.
The extra information is stored in /debug/dri/.../i915_error_state
following an error, and may be decoded using
intel_gpu_tools/tools/intel_error_decode.
v2: Avoid excessive work under spinlocks.
v3: Include ringbuffer for later analysis.
v4: Use kunmap correctly and record more buffer state.
v5: Search ringbuffer for current batch buffer
v6: Use a work fn for the impossible IRQ error case.
v7: Avoid non-atomic paths whilst in IRQ context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
These old machines more often than not lie about their lid state. So
don't use it to detect LVDS presence, but leave the event handler to
deal with lid open/close, when we might need to reset the mode.
Fixes kernel bug #15248
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
i915_gem_object_fenceable was mostly just a repeat of the
i915_gem_object_fence_offset_ok, but also checking the size (which was
checkecd when we allowed that BO to be tiled in the first place). So
instead, export the latter function and use it in place.
Signed-Off-By: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This aligns it with the other user of i915_gem_clear_fence_reg,
which blows away the mapping before changing the fence reg.
Only affects userspace if it races against itself when changing
tiling parameters, i.e. behaviour is undefined, anyway.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
No functional change, because gtt flushing is a no-op. Still, try
to keep the bookkeeping accurate. The if is still slightly wrong
for with execbuf2 even i915-class hw doesn't always need a fence
reg for gpu access. But that's for somewhen lateron.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cache-coherency is maintained by gem. Drop these leftover MI_FLUSH
commands from the userspace code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
I retested this and whatever this papered over, the problem doesn't seem
to exist anymore.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eric Anholt <eric@anholt.net>
[anholt: fixed up compile warning]
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 84b79f8d28 (drm/i915: Fix crash
while aborting hibernation) attempted to fix a regression introduced
by commit cbda12d77e (drm/i915:
implement new pm ops for i915), but it went too far trying to split
the freeze/suspend and resume/thaw parts of the code. As a result,
it introduced another regression, which only is visible on some systems.
Fix the problem by merging i915_drm_suspend() with
i915_drm_freeze() and moving some code from i915_resume()
into i915_drm_thaw(), so that intel_opregion_free() and
intel_opregion_init() are also executed in the freeze and thaw code
paths, respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Pedro Ribeiro <pedrib@gmail.com>
Tested-by: Tino Keitel <tino.keitel@tikei.de>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tools like powertop want to check the current FBC status and report it
to the user. So add a debugfs file indicating whether FBC is enabled,
and if not, why.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
At unload time, we need to disable DRPS, but we need to do it correctly
or the GPU will hang and we won't be able to load the module again. So
set the SFCAVM bit so we can properly restore the DRPS config at unload.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
He Shuang reported an OGLC performance regression introduced in the patch
"enable memory self refresh on 9xx", In that patch, SR on 945 is disabled
everytime when calling intel_mark_busy(), while too much of such operation
will impact performance. Actually disable SR is necessary only when GPU and
Crtc changing from idle to busy. This patch make such optimization.
It fixes upstream bug
http://bugs.freedesktop.org/show_bug.cgi?id=26422
Signed-off-by: Li Peng <peng.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The ironlake render p-state support includes some rather odd variable
names. Clean them up in order to improve the readability of the code.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Ironlake (and 965GM, which this patch doesn't support) supports a
hardware performance and power management feature that allows it to
adjust to changes in GPU load over time with software help. The goal
if this is to maximize performance/power for a given workload.
This patch enables that feature, which is also a requirement for
supporting Intelligent Power Sharing, a feature which allows for
dynamic budgeting of power between the CPU and GPU in Arrandale
platforms.
Tested-by: ykzhao <yakui.zhao@intel.com>
[anholt: Resolved against the irq handler loop removal]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Enabling memory self refresh (SR) on 9xx needs to set additional
register bits. On 945, we need bit 31 of FW_BLC_SELF to enable the
write to self refresh bit and bit 16 to enable the write of self
refresh watermark. On 915, bit 12 of INSTPM is used to enable SR.
SR will take effect when CPU enters C3+ state and its entry/exit
should be automatically controlled by H/W, driver only needs to set
SR enable bits in wm update. But this isn't safe in my test on 945
because GPU is hung. So this patch explicitly enables SR when GPU
is idle, and disables SR when it is busy. In my test on a netbook of
945GSE chipset, it saves about 0.8W idle power.
Signed-off-by: Li Peng <peng.li@intel.com>
[anholt: rebased against 33c5fd121e
by adding disable of INSTPM SR bit on 915GM for two pipe setup]
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: bump the UMS driver version number to indicate rv740 fix
drm/radeon/kms: free fence IB if it wasn't emited at IB free time
drm/ttm: fix caching problem on non-PAT systems.
drm/radeon/rv740: fix backend setup
drm/radeon/kms: fix shared ddc detection
drm/radeon/kms/rs600: add connector quirk
vgaarb: fix "target=default" passing
This lets UMS userspace know the rv740 fix is in. For KMS we can
consider the kernel release to be the v2.0.0 release so we don't need the
bump there.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If at IB free time fence wasn't emited that means the IB wasn't
scheduled because an error occured somewhere, thus we can free
then fence and mark the IB as free.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
http://bugzilla.kernel.org/show_bug.cgi?id=15328
This fixes a serious regression on AGP/non-PAT systems, where
pages were ending up in the wrong state and slowing down the
whole system.
[airlied: taken this from the bug as the other option is to revert
the change which caused it].
Tested-by: John W. Linville (in bug).
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes occlusion queries and rendering errors
on rv740 boards. Hardcoding the backend map is not an optimal
solution, but a better fix is being worked on.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just compare the i2c id since the i2c structs
may be slighly different.
Fixes fdo bug 26616.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 board lists DVI port as HDMI.
Fixes fdo bug 26605
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: fix "acpi=ht" boot option
ACPI, i915: blacklist Clevo M5x0N bad_lid state
ACPI: fix High cpu temperature with 2.6.32
ACPI: dock: properly initialize local struct dock_station in dock_add()
ACPI: remove Asus P2B-DS from acpi=ht blacklist
thinkpad-acpi: wrong thermal attribute_group removed in thermal_exit()
ACPI: acpi_bus_{scan,bus,add}: return -ENODEV if no device was found
ACPI: Add NULL pointer check in acpi_bus_start
ACPI: processor: only evaluate _PDC once per processor
ACPI: processor: add kernel command line support for early _PDC eval
* 'for-airlied' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: Force TV encoder DPMS reinit after resume.
drm/nouveau: use mutex for vbios lock
Previous code did associate fence to bo before the fence was emited
and it also didn't lock protected access to ttm sync_obj member.
Both of this flaw leads to possible race between different code
path. This patch fix this by associating fence only once the fence
is emitted and properly lock protect access to sync_obj member of
ttm.
Fix:
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely similar others bugs
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is 3 different distinct states for an indirect buffer (IB) :
1- free with no fence
2- free with a fence
3- non free (fence doesn't matter)
Previous code mixed case 2 & 3 in a single one leading to possible
catastrophique failure. This patch rework the handling and properly
separate each case. So when you get ib we set the ib as non free and
fence status doesn't matter. Fence become active (ie has a meaning
for the ib code) once the ib is scheduled or free. This patch also
get rid of the alloc bitmap as it was overkill, we know go through
IB pool list like in a ring buffer as the oldest IB is the first
one the will be free.
Fix :
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely other bugs.
V2 remove the scheduled list, it's useless now, fix free ib scanning
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When the vmwgfx module is loaded on top of vesafb, it would operate in
stealth mode in parallel with vesafb, evicting VRAM on dropmaster.
Change that to use the vesafb handover mechanism, like other drmfb drivers.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For usec delays use udelay instead of scheduling, this should
allow reclocking to happen faster. This also was the cause
of reported 33s delays at bootup on certain systems.
fixes: freedesktop.org bug 25506
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Get rid of _location and use _start/_end also simplify the
computation of vram_start|end & gtt_start|end. For R1XX-R2XX
we place VRAM at the same address of PCI aperture, those GPU
shouldn't have much memory and seems to behave better when
setup that way. For R3XX and newer we place VRAM at 0. For
R6XX-R7XX AGP we place VRAM before or after AGP aperture this
might limit to limit the VRAM size but it's very unlikely.
For IGP we don't change the VRAM placement.
Tested on (compiz,quake3,suspend/resume):
PCI/PCIE:RV280,R420,RV515,RV570,RV610,RV710
AGP:RV100,RV280,R420,RV350,RV620(RPB*),RV730
IGP:RS480(RPB*),RS690,RS780(RPB*),RS880
RPB: resume previously broken
V2 correct commit message to reflect more accurately the bug
and move VRAM placement to 0 for most of the GPU to avoid
limiting VRAM.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r200 cards have dma engine which can be used to tranfer data
between vram and system memory.
r300 dma engine registers match r200 dma engine. Enabling
dma copy for r200 is simple as hooking r200 asic to already
existing function r300_copy_dma.
Rename r300_dma_copy to r200_dma_copyto reflect that supports
starts from r200 cards.
v2: Created a new asic object for r200 cards.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Setting global asic structure to point to different function
would cause problem in system where is multiple r300 cards
with different bus type.
r300_asic_pcie is just copy from r300_asic with gart tlb
functions replaced with pcie versions.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
r6xx/r7xx use the rs600 variant. This old one just
confuses things.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We should stop audio-state-reading timer before we turn off engine
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/radeon/r600_cs.c: In function ‘r600_cs_track_check’:
drivers/gpu/drm/radeon/r600_cs.c:166: warning: ‘bpe’ may be used uninitialized in this function
drivers/gpu/drm/radeon/r600_cs.c:166: note: ‘bpe’ was declared here
drivers/gpu/drm/radeon/r600_cs.c: In function ‘r600_cs_parse’:
drivers/gpu/drm/radeon/r600_cs.c:938: warning: ‘bpe’ may be used uninitialized in this function
drivers/gpu/drm/radeon/r600_cs.c:938: note: ‘bpe’ was declared here
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fence start is for compatibility with UMS X Servers before fence
management. KMS X Servers only started doing tiling after fence
management appeared.
Signed-off-by: Eric Anholt <eric@anholt.net>
As we need more and more controls within MCHBAR for memory config and
power management, this trys to keep MCHBAR enabled from driver load and
only tear down in driver unload.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
With the introduction of the hang-check, we can safely expect that
i915_wait_request() will always return even when the GPU hangs, and so
do not need to open code the wait in order to manually check for the
hang. Also we do not need to always evict all buffers, so only flush
the GPU (and wait for it to idle) for KMS, but continue to evict for UMS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Wrong Lid state reported.
Need to blacklist this machine for LVDS detection.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previous code did associate fence to bo before the fence was emited
and it also didn't lock protected access to ttm sync_obj member.
Both of this flaw leads to possible race between different code
path. This patch fix this by associating fence only once the fence
is emitted and properly lock protect access to sync_obj member of
ttm.
Fix:
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely similar others bugs
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There is 3 different distinct states for an indirect buffer (IB) :
1- free with no fence
2- free with a fence
3- non free (fence doesn't matter)
Previous code mixed case 2 & 3 in a single one leading to possible
catastrophique failure. This patch rework the handling and properly
separate each case. So when you get ib we set the ib as non free and
fence status doesn't matter. Fence become active (ie has a meaning
for the ib code) once the ib is scheduled or free. This patch also
get rid of the alloc bitmap as it was overkill, we know go through
IB pool list like in a ring buffer as the oldest IB is the first
one the will be free.
Fix :
https://bugs.freedesktop.org/show_bug.cgi?id=26438
and likely other bugs.
V2 remove the scheduled list, it's useless now, fix free ib scanning
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In testing I've never seen it go past 1 retry anyways but better
safe than sorry.
Reported by Droste on irc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Noticed on a DEC Alpha.
Start up into console mode caused 15 unaligned accesses, and starting X
caused another 48.
Signed-off-by: Matt Turner <mattst88@gmail.com>
CC: Jerome Glisse <jglisse@redhat.com>
CC: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the buffer object was already in the requested memory type, but
outside of the requested range it was never moved into the requested range.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When searching for free space in a range, the function could return a node extending outside of the given range.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: hold ref on flip object until it completes
drm/i915: Fix crash while aborting hibernation
drm/i915: Correctly return -ENOMEM on allocation failure in cmdbuf ioctls.
drm/i915: fix pipe source image setting in flip command
drm/i915: fix flip done interrupt on Ironlake
drm/i915: untangle page flip completion
drm/i915: handle FBC and self-refresh better
drm/i915: Increase fb alignment to 64k
drm/i915: Update write_domains on active list after flush.
drm/i915: Rework DPLL calculation parameters for Ironlake
This is partial revert of commit 9404c9c392d5 ("Fix misspelling of "should"
and "shouldn't" in comments"). According to Dave Airlie:
"Can we drop any cleanups to atombios.h? This file comes from
AMD and we normally drop it into place, so they just get overwritten
next time."
Reported-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
radeon_cs kfree the tracker structure but for r6xx/r7xx we want
to kfree it inside the parse function because we share it with
the UMS code path. Set tracker to NULL after freeing it will
avoid double free.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this uses a new entrypoint to invalidate gart entries instead of using 0.
Changed to rather than pointing to 0 address point empty entry to dummy
page. This might help to avoid hard lockup if for some wrong
reasons GPU try to access unmapped GART entry.
I'm not 100% sure this is going to work, we probably need to allocate
a dummy page and point all the GTT entries at it similiar to what AGP does.
but we can test this first I suppose.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's happened time and time again (most recently with the support for EDID
hardcoded in the BIOS ROM) that new code didn't check for rdev->bios being
non-NULL before triggering dereferences of it. This would result in an
oops/panic on setups with no BIOS ROM. Hopefully this central test will be
more robust.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch add cs checker to r600/r700 hw. Command stream checking
will rewrite some of the cs value in order to restrict GPU access
to BO size. This doesn't break old userspace but just enforce safe
value. It should break any things that was using the r600/r700 cs
ioctl to do forbidden things (malicious software), though we are
not aware of such things.
Here is the list of thing we check :
- enforcing resource size
- enforcing color buffer slice tile max, will restrict cb access
- enforcing db buffer slice tile max, will restrict db access
We don't check for shader bigger than the BO in which they are
supposed to be, such use would lead to GPU lockup and is harmless
from security POV, as far as we can tell (note that even checking
for this wouldn't prevent someone to write bogus shader that lead
to lockup).
This patch has received as much testing as humanly possible with
old userspace to check that it didn't break such configuration.
However not all the applications out there were tested, thus it
might broke some odd, rare applications.
[airlied: fix rules for cs checker for parallel builds]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
[clemens@ladisch.de: merged into drm_fb_helper]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
a patch from Roel was wrong, fix this properly, really
if the fb ptrs are different fb changed shuold be true.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Kernel has simple_strtol() which would be used as atoi().
This is quite the same fix as in 2cb96f8662
("fbdev: drop custom atoi from drivers/video/modedb.c") because code in
drivers/gpu/drm/drm_fb_helper.c is based on drivers/video/modedb.c.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These ioctls are all protected by their own locking mechanisms so
should be fine to not bother locking around.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Mostly obvious simplifications.
The i915 pread/pwrite ioctls, intel_overlay_put_image and
nouveau_gem_new were incorrectly using the locked versions
without locking: this is also fixed in this patch.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch introduces the drm_gem_object_unreference_unlocked
and drm_gem_object_handle_unreference_unlocked functions that
do not require holding struct_mutex.
drm_gem_object_unreference_unlocked calls the new
->gem_free_object_unlocked entry point if available, and
otherwise just takes struct_mutex and just calls ->gem_free_object
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-linus' of ../drm-next:
drm/radeon/kms: retry auxch on 0x20 timeout value.
drm/radeon: Skip dma copy test in benchmark if card doesn't have dma engine.
drm/radeon/kms: fix screen clearing before fbcon.
drm/radeon/kms: add quirk for VGA without DDC on rv730 XFX card.
drm/radeon/kms: don't crash if no DDC bus on VGA/DVI connector.
drm/radeon/kms: change Kconfig text to reflect the new option.
drm/radeon/kms: suspend and resume audio stuff
ATOM appears to return 0x20 which seems to mean some sort of timeout.
retry the transaction up to 10 times before failing, this
makes DP->VGA convertor we bought work at least a bit more predictably.
Signed-off-by: Dave Airlie <airlied@redhat.com>
original evergreen patches we against a kernel tree
without my radeon i2c algo changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix a typo in crtc offset setup that set the crtc
instances wrong for all crtcs except the first.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pre-pcie chips seem to use the reference clock
rather than the sclk.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rafał Miłecki
Alex Deucher
Ben Skeggs
Francisco Jerez
Jerome Glisse
Linus Torvalds
Maarten Maathuis
Marcin Kościelnicki
Jiri Kosina
Emese Revfy
Andi Kleen
Don Mullis
Dave Airlie
Pauli Nieminen
Dave Airlie
Matt Turner
Zhao Yakui
Jesse Barnes
Daniel Vetter
Zhenyu Wang
Eric Anholt
Luca Barbieri
Marcin Slusarz
Marek Olšák
Thomas Hellstrom
Chris Wilson
Owain Ainsworth
Rafael J. Wysocki
Li Peng
Matthew Garrett
Len Brown
Adam Jackson
Zhang Rui
Michel Dänzer
Pavel Roskin
Andy Shevchenko