this patch removes compatibility with 2.4 kernel, which makes
the code much easier to read.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as622) makes gadgetfs set the "zero" flag for control-IN
responses, when the length of the response is shorter than the length of
the request.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace mdelay() by msleep() in bus_suspend(); the rest of the system will
gain 7ms. The related code is reorganized to minimize the number of
locking/unlocking calls.
The last hunk of the patch is the formatting change by Lindent.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For some reason alpha doesn't include <linux/dma-mapping.h> where other
architectures do; this makes net2280 include it explicitly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB devices don't enumerate well with FSBR turned on. This patch
keeps devices on the low-speed part of the schedule (which doesn't use
FSBR) until they have been fully configured.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a reinitializion for the uf variable that got modified
by the preceding start-split bandwidth check.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My earlier experiment (adding a clear-halt for the interrupt-in
endpoint) failed. It turns out that it does cause problems for other
devices. And it wasn't needed anyway; a simple blacklist entry was
enough to get my HP keyboard working.
This patch (as643) removes the clear-halt call and adds the blacklist
entry.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add device support for a couple more Auerswald TK-devices.
Via Thomas Jackle <dj-tj@gmx.de>, typed in from
http://bugzilla.kernel.org/show_bug.cgi?id=5908.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch correct a possible bug with cmv_name being static. If there
is 2 modems and the driver is scheduled when filling cmv_name this could
result with garbage in cmv_name. We allocate cmv_name on the stack but
with a small size in order to avoid that.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the support for isochronous pipe.
A new module parameter is added to select iso mode. It is set to iso by
default because bulk mode doesn't work well at high speed rate (>3 Mbps
for upload).
We use UDSL_IGNORE_EILSEQ flags because ADI firmware doesn't reply to
ISO IN when it has nothing to send [1].
[1]
from cypress datasheet :
The ISOSEND0 Bit (bit 7 in the USBPAIR Register) is used when the EZ-USB
FX chip receives an isochronous IN token while the IN FIFO is empty. If
ISOSEND0=0 (the default value), the USB core does not respond to the IN
token. If ISOSEND0=1, the USB core sends a zero-length data packet in
response to the IN token. The action to take depends on the overall
system design. The ISOSEND0 Bit applies to all of the isochronous IN
endpoints, IN-8 through IN-15.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the usbatm part of the Arjan, Jes and Ingo
mass semaphore to mutex conversion, reworked to apply on top
of the patches I just sent to you. This time, with correct
attribution and signed-off lines.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't throttle on -EILSEQ urb status if requested by a minidriver.
It seems the ueagle modems are buggy, giving -EILSEQ when they
have no data to send. The ueagle change will be sent separately
by the ueagle guys. Patch by Matthieu Castet.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The receive logic has always assumed that urbs contain an integral
number of ATM cells, which is a bit naughty, though it never caused
any problems with bulk transfers. Isochronous urbs spank us soundly
for this. Fixed thanks to this patch, mostly by Stanislaw Gruszka.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While the usbatm core has had some support for using isoc urbs
for some time, there was no way for users to turn it on. While
use of isoc transfer should still be considered experimental, it
now works well enough to let users turn it on. Minidrivers signal
to the core that they want to use isoc transfer by setting the new
UDSL_USE_ISOC flag. The speedtch minidriver gets a new module
parameter enable_isoc (defaults to false), plus some logic that
checks for the existence of an isoc receive endpoint (not all
speedtouch modems have one).
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the module parameters rcv_buf_size and snd_buf_size to
specify buffer sizes in bytes rather than ATM cells. Since
there is some danger that users may not notice this change,
the parameters are renamed to rcv_buf_bytes etc. The transmit
buffer needs to be a multiple of the ATM cell size in length,
while the receive buffer should be a multiple of the endpoint
maxpacket size (this wasn't enforced before, which causes trouble
with isochronous transfers), so enforce these restrictions. Now
that the usbatm probe method inspects the endpoint maxpacket size,
minidriver bind routines need to set the correct alternate setting
for the interface in their bind routine. This is the reason for
the speedtch changes.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In one spot (usbatm_cancel_send) we were calling dev_kfree_skb with irqs
disabled. This mistake is just too easy to make, so systematically use
dev_kfree_skb_any rather than dev_kfree_skb.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch causes vcc_release_async to be applied to any open
vcc's when the modem is disconnected. This signals a socket
shutdown, letting the socket user know that the game is up.
I wrote this patch because of reports that pppd would keep
connections open forever when the modem is disconnected.
This patch does not fix that problem, but it's a step in the
right direction. It doesn't help because the pppoatm module
doesn't yet monitor state changes on the ATM socket, so simply
never realises that the ATM connection has gone down (meaning
it doesn't tell the ppp layer). But at least there is a socket
state change now. Unfortunately this patch may create problems
for those rare users like me who use routed IP or some other
non-ppp connection method that goes via the ATM ARP daemon: the
daemon is buggy, and with this patch will crash when the modem
is disconnected. Users with a buggy atmarpd can simply restart
it after disconnecting the modem.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xusbatm driver is for otherwise unsupported modems.
All it does is grab hold of a user-specified set of
interfaces - the generic usbatm core methods (hopefully)
do the rest. As Aurelio Arroyo discovered when he tried
to use xusbatm (big mistake!), the interface grabbing logic
was completely borked. Here is a rewrite that works.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Have minidrivers and the core signal special requirements
using a flags field in struct usbatm_data. For the moment
this is only used to replace the need_heavy_init bind
parameter, but there'll be new flags in later patches.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a Video4Linux2 driver giving support
to ET61X151 and ET61X251 PC Camera Controllers made by
Etoms Electronics.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates:
- Use kzalloc() instead of kmalloc()
- Move some macro definitions from sn9c102.h to sn9c102_core.c
- Use vfree() and vmalloc_32() instead of rvfree() and rvmalloc()
- Fix mmap() sys call
- Documentation updates
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch adds four new device IDs for the CP2101 driver.
Also 3 tab characters have been removed from device ID table.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added support for CA-42 clone cable (www.ca-42.com)
Signed-off-by: Martin Gingras <martin.gingras@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects the URB initialisation for transfers
like this is done in other drivers too.
Without this patch no data was transmitted on a PXA270 OHCI
platform. May apply to others too.
Signed-off-by: Juergen Schindele <schindele@nentec.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add device IDs for the 0G0 Cable Ethernet device as reported by
Charles Lepple <clepple@gmail.com>.
Signed-off-by: David Hollis <dhollis@davehollis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates and bugfixes.
Changes: + new, - removed, * cleanup, @ bugfix:
@ fix poll()
@ Remove bad get_ctrl()'s
* Reduce ioctl stack usage
* Remove final ";" from some macro definitions
* Better support for SN9C103
+ Add sn9c102_write_regs()
+ Add 0x0c45/0x602d to the list of SN9C10x based devices
+ Add support for OV7630 image sensors
+ Provide support for the built-in microphone interface of the SN9C103
+ Documentation updates
+ Add 0x0c45/0x602e to the list of SN9C10x based devices
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've been offered a nice Sony DSC-T5 digital camera, with a USB connection.
Unfortunately it is not recognized by Linux 2.6.14.4's usb-storage.
With the following change I'm able to mount and read my pictures:
Signed-off-by: Phil Dibowitz <phil@ipom.com>
this fixes
-potential hang by disconnecting through usbfs
-kzalloc
-general cleanup
-micro optimisation in interrupt handlers
It compiles and I am printing.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch from Bob Copeland adds support for the Rio Karma portable
digital audio player to the usb-storage driver. The only thing needed to
support this device is a one-time (per plugin) init command which is sent
to the device.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This should fix things mentioned below:
"I was curious why my firewall was loading a 'phone driver'.
It turns out that the probing in the yealink driver is
a little too assuming..
static struct usb_device_id usb_table [] = {
{ USB_INTERFACE_INFO(USB_CLASS_HID, 0, 0) },
{ }
};
So it picked up my UPS, and loaded the driver.
Whilst no harm came, because it later checks the vendor/product IDs,
this driver should probably be rewritten to only probe
for the device IDs it actually knows about.
Dave"
Signed-off-by: Henk Vergonet <henk.vergonet@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Documentation: Specify grayscale specification on ATIK-ATK16
and ATIK-ATK16HR comments.
New: Add ProductID and VendorID for devices ATIK-ATK16C and
ATIK-ATK16HRC. These devices are also USB Astronomical CCD
cameras that work through an FTDI 245BM chip, share the
same base hardware but, it has a colour CCD chip instead
of a grayscale one.
Signed-off-by: Rui Santos <rsantos@grupopie.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch adds a new PID for the ftdi_sio driver. It will
enable support for PC-DJ's DAC-2 controller module
(more information on http://www.pcdjhardware.com/DAC2.asp)
Signed-off-by: Wouter Paesen <wouter@kangaroot.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds two new devices to the ftdi_sio driver's device ID
table. The device IDs were supplied by Cory Lee to support two POS
printers made by Westrex International (Model 777 and Model 8900F).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch includes the Vendor Id for a optic fiber to USB device named
TTUSB from thought Technology. It's just add the vendor Id to
ftdi_sio.h and add the Vendor ID and model Id to table_combined.
Signed-off-by: Louis Nyffenegger <louis.nyffenegger@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For crying out loud, they have devices which do not like port resets.
So, do what usb-storage does and try both bulk and port resets.
We start with a port reset (which usb-storage does at the end of transport),
then do a Bulk reset, then a port reset again. This seems to work for me.
The code is getting dirtier and dirtier here, but I swear that I'll
do something about it (see those two new XXX). Honest.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If SCSI commands are submitted while other commands are still processed,
the dispatch loop turns, and we stop the work_timer. Then, if URB fails
to complete, ub hangs until the device is unplugged.
This does not happen often, becase we only allow one SCSI command per
block device, but does happen (on multi-LUN devices, for example).
The fix is to stop timer only when we actually going to change the state.
The nicest code would be to have the timer stopped in URB callback, but
this is impossible, because it can be called from inside a timer, through
the urb_unlink. Then we get BUG in timer.c:cascade(). So, we do it a
little dirtier.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The blk_cleanup_queue does not necesserily destroy the queue. When we
destroy the corresponding ub_dev, it may leave the queue spinlock pointer
dangling.
This patch moves spinlocks from ub_dev to static memory. The locking
scheme is not changed. These spinlocks are still separate from the ub_lock.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the previously widely-used ehci-pci.c BIOS handoff
code into the pci-quirks.c file, replacing the less widely used
"early handoff" version that seems to cause problems lately.
One notable change: the "early handoff" version always enabled
an SMI IRQ ... and did so even if the pre-Linux code said it was
not using EHCI (and not expecting EHCI SMIs). Looks like a goof
in a workaround for some unknown BIOS version.
This merged version only forcibly enables those IRQs when pre-Linux
code says it's using EHCI. And now it always forces them off "just
in case".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revert: 40727198bf
These PHY changes hang the sungem driver on startup with Sun chips on
sparc64. Hopefully we can redo these changes in a way that doesn't
break non-Apple systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
A critical thing the ServeRAID driver MUST do is hide the physical DASDI
devices from the OS. It does this by intercepting the INQUIRY commands.
In recent 2.6.15 testing, I discovered this to be failing.
The cause was the driver assuming that the INQUIRY response data was in a
simple single buffer, when it was actually a 1 element scatter gather list.
This patch makes ips always look at the correct data when examining an
INQUIRY response.
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds a sanity check in the interrupt routine
insures incoming message frames are a valid
message frames.
The code for setting 0xdeadbeaf in the freed message
frames, apparently was already submitted by Christoph
in previous patch submission.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch inhibits sending spi negotiation parameters
for non-configured devices from the slave_destroy function.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The ioc->alt_ioc->alt_ioc pointer is not getting cleared
during driver unload time. This dangling pointer
can result in panic in certain circumstances, such
as error recovery, or firmware download in flashless
environments. This only impacts dual functions controllers,
such as 1030. Please apply.
This patch also includes a small cosmetic name change
for mpt_spi_log_info.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When people use the userspace scanning facilities on SAS hardware the
LLDD gets bogus slave_alloc calls. Just fail those gracefully instead
of printing a warning in mptsas and another one in the midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding verbose message returned from firmware
when a task mangment request fails.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Mon, Jan 16, 2006 at 06:53:24PM -0700, Moore, Eric wrote:
> Adding MSI support, and command line for enabling
> it. By default, the command line option has MSI disabled.
mpt_msi_enable is initialized to 0 implicitly, no need to do that. Also
replace if (mpt_msi_enable == 1) tests with just if (mpt_msi_enable).
Updated patch below:
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A customer request to send raid asyn actions
from firmware to the event syslog. This shows
when raid volumes go degraded, or complete resync,
or volumes created/deleted, etc.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Increasing the reply frame size by 16 bytes, to
be in sync with the other fusion drivers.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Mon, Jan 16, 2006 at 06:53:13PM -0700, Moore, Eric wrote:
> The task managment request timeout in the eh threads was set
> for U320 timing, which is between 2-5 seconds.
> This is too small for FC and SAS.
> According to the firmware engineers, Fibre needs to be 40 seconds
> and SAS needs to be 10 seconds.
The timeout selection should probably be done in a little helper instead
of duplicated in a few places. Updated patch below.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Increase the port enable timeout only for SAS from 30 to 300 seconds.
A customer request for the handling large topologies.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch is for spi. This issues bus reset when driver
loads. Handling cases when initator has negotiated for packetized,
and target negotiated for non-packetized; effectly this bus reset
is getting both target and initiator on the same sheet of music.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix the timer handling in aic79xx to use the SCSI-ML provided handling
instead of implementing our own.
It also fixes a deadlock in the command recovery code.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the aic79xx sequencer with latest fixes from adaptec.
The sequencer code now corresponds with adaptec version 2.0.15.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The prior fusion patches moved an invocation of a function,
mptscsih_TMHandler(), static to mptscsih.c into mptsas.c
Make the function unstatic, move the header to mptscsih.h and export it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fix's problems with recent fc submission regarding
i/o being redirected to the wrong target.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This moves code intented for SAS from
the generic mptscsih module over to the
mptsas module.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The issuing of the target reset
used in device hot removal case so the
firmware queue is flushed out off outstanding
commands.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
RAID event support.
This will hot add and remove raid volumes
when managment application creates and
deletes the volumes. The driver is basically
responding to firmware asyn events, and reporting
the changes to the above layers.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch displays the port identifier on
the folder attribute; located in the middle digit.
/sys/class/sas_rphy/rphy-%x:%x:%x
The port identifier is basically the unique identifier
for each sas domain.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The lock validator caught another one: drivers/pci/msi.c is accessing
&irq_desc[i].lock with interrupts enabled (!).
The fix is to disable interrupts properly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some users have commented that it is unclear which driver they should be
using for their Marvell/SysKonnect network adapter, and which ones
are/aren't interchangable.
This patch attempts to reduce the confusion.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Implemented support in the Resource Manager to allow
unresolved namestring references within resource package
objects for the _PRT method. This support is in addition
to the previously implemented unresolved reference
support within the AML parser. If the interpreter slack
mode is enabled (true on Linux unless acpi=strict),
these unresolved references will be passed through
to the caller as a NULL package entry.
http://bugzilla.kernel.org/show_bug.cgi?id=5741
Implemented and deployed new macros and functions for
error and warning messages across the subsystem. These
macros are simpler and generate less code than their
predecessors. The new macros ACPI_ERROR, ACPI_EXCEPTION,
ACPI_WARNING, and ACPI_INFO replace the ACPI_REPORT_*
macros.
Implemented the acpi_cpu_flags type to simplify host OS
integration of the Acquire/Release Lock OSL interfaces.
Suggested by Steven Rostedt and Andrew Morton.
Fixed a problem where Alias ASL operators are sometimes
not correctly resolved. causing AE_AML_INTERNAL
http://bugzilla.kernel.org/show_bug.cgi?id=5189http://bugzilla.kernel.org/show_bug.cgi?id=5674
Fixed several problems with the implementation of the
ConcatenateResTemplate ASL operator. As per the ACPI
specification, zero length buffers are now treated as a
single EndTag. One-length buffers always cause a fatal
exception. Non-zero length buffers that do not end with
a full 2-byte EndTag cause a fatal exception.
Fixed a possible structure overwrite in the
AcpiGetObjectInfo external interface. (With assistance
from Thomas Renninger)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Found this when working with a HAPP UGCI device. It has a usage with 7
indexes. I could read them all one at a time, but using a multiref it
would only allow me to read the first 6. The patch below fixed it.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Recent conversion to wait_event_interruptible_timeout() caused
USB detection routine erroneously report timeouts for perfectly
working devices.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Convert semaphores to mutexes in mthca. Leave firmware command
interface poll_sem and event_sem as semaphores.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have run into the following problem: if a task receives a signal
while in the process of e.g. destroying a resource (which could be
because the relevant file was closed) mthca could bail out from trying
to take a command interface semaphore without performing the
appropriate command to tell hardware that the resource is being
destroyed.
As a result we see messages like
ib_mthca 0000:04:00.0: HW2SW_CQ failed (-4)
In this case, hardware could access the resource after the memory has
been freed, possibly causing memory corruption.
A simple solution is to replace down_interruptible() by down() in
command interface activation.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
[ It's also not safe to bail out on multicast table operations, since
they may be invoked on the cleanup path too. So use down() for
mcg_table.sem too. ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert srp_host->target_mutex from a semaphore to a mutex.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are some cards around that have UAR (user access region) size
different from 8 MB. Relax our sanity check to make sure that the PCI
BAR is big enough to access the UAR size reported by the device
firmware instead.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
CONFIG_PCMCIA=m, CONFIG_HOSTAP_CS=y doesn't compile.
Reported by "Gabriel C." <crazy@pimpmylinux.org>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ipw2100 driver misunderstood the parameter of txpower.
Tx Power off means turn off the radio, but the driver interpret it as
"can't set txpower". So when getting the txpower, it sets disabled=1 to
the iwconifg tool in managed mode. And the tool will display "Tx Power off"
when disabled=1.
Now, in managed mode, iwconfig will not show "TX Power" if the radio is not
switched off. It will only display "Tx Power off" only if the radio is killed.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ipw2100.c:2236: warning: `ipw2100_match_buf' defined
but not used
Cc: Yi Zhu <yi.zhu@intel.com>
Cc: James Ketrenos <jketreno@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently, "while true; do cat </dev/null >/dev/input/mice; done" causes
an OOM in a short amount of time. Funny that nobody noticed, it actually
is very easy to trigger just by switching between VT1 and VT7...
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a driver for beeper found in LinkSys NSLU2 boxes. It should work
on any ixp4xx based platform.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch defines a new template to represent each type of
controllers (identified by the processor used). The template has
members that is set with appropriate values during driver
initialisation. This change is done to support new controllers with
minimal change to existing code. In future, for a new controller
support, a template will be declared and its members initialised
appropriately.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch (originally submitted by Christoph Hellwig) removes code
duplication in megasas_build_cmd. It also defines
MEGASAS_IOC_FIRMWARE32 to allow 64 bit compiled applications to work.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The current orinoco_cs.c can issue the exact same error message for
2 different tests that can fail. Alter them so we can tell which
one of the two failed.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Userspace governor need not to hold it's own cpufreq_policy,
better make use of the global core policy.
Also fixes a bug in case of frequency changes via _PPC.
Old min/max values have wrongly been passed to __cpufreq_driver_target()
(kind of buffered) and when max freq was available again, only the old
max(normally lowest freq) was still active.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
cpufreq_userspace.c | 53 +++++++++++++++++++++++++++-------------------------
1 files changed, 28 insertions(+), 25 deletions(-)
Update dev->last_rx on packet receive
This fix corrects errors seen during configuration of the bonding driver.
Signed-off-by: Paolo Galtieri <pgaltieri@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch eliminates a spinlock recursion bug introduced recently.
Since eth_port_send() is always called with the lock held, we simply
remove the locking inside the function itself.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There is a problem with fragmented skb in s2io driver version 2.0.9.4
available in 2.6.16-rc1 kernel. The adapter will fail to transmit if
any scatter-gather skb arrives. This patch provides fix for the above
described problem.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
On my laptop, the b44 device is created and the carrier state defaults
to ON when created by alloc_etherdev. This means tools like NetworkManager
see the carrier as On and try and bring the device up. The correct thing
to do is mark the carrier as Off when device is created.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Since get_settings() returns a signed int and it gets checked
for < 0 to catch an error, res should be a signed int too.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
In the case where a (broken) BIOS gives us a blank _CRS for
a PCI Interrupt Link Device, the acpi_walk_resources()
will not terminate, but will then give the callback
the resource end tag. Ignore the end tag.
Signed-off-by: Len Brown <len.brown@intel.com>
When the scsi_execute_async interface was added it ended up reducing
the flexibility of userspace to send arbitrary scsi commands through
sg using SG_IO. The SG_IO interface allows userspace to specify the
CDB length. This is now ignored in scsi_execute_async and it is
guessed using the COMMAND_SIZE macro, which is not always correct,
particularly for vendor specific commands. This patch adds a cmd_len
parameter to the scsi_execute_async interface to allow the caller
to specify the length of the CDB.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
BIOS might change frequency behind our back when BIOS changes allowed
frequencies via _PPC. In this case cpufreq core got out of sync.
Ask driver for current freq and notify governors about a change
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Patch from Lucas Correia Villa Real
This patch defines S3C2400 memory map and adds a S3C24XX macro for
common resources between S3C2400, S3C2410 and S3C2440 cpus.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some folk want to use RGB555 rather tahn RGB565 with amba-clcd.
Allow amba-clcd to accept either pixel format.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Resetting the adapter causes the ServeRAID driver to exceed
the max time allowed by the softlock watchdog. Resetting the
hardware can easily require 30 or more seconds. To avoid the
"BUG: soft lockup detected on CPU#0!"
result, this patch replaces the mdelay() calls in the
initialization/reset routines with msleep().
Signed-off-by: Jack Hammer <jack_hammer@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Internal lun discovery has been removed since fc_transport
integration. Short-circuiting for tape-devices in
qla2x00_update_fcport() could inadvertently result in a
blocked rport timing-out and its targets being reaped.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A target can LOGO an initiator at any time (i.e. during I/O,
due to a controller hicup, or as a simple authentication
mechanism after an initial CDB command), when this occurs,
the driver attempts to relogin (PLOGI) to the device via the
DPC thread. Add code to make the appropriate upcall to the
FC transport layer (fc_remote_port_add()) upon successful
completion of the PLOGI.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver can typically detect port-loss during an
interrupt context (i.e. via interrogation of a status IOCB's
completion status [CS_PORT_LOGGED_OUT]. Due to the calling
requirements of the fc_rport APIs, the driver would defer
removal of the device to the default workqueue. If the
work-item was preceded by an event which caused the port to
obtain visibility (relogin successful, target re-logged into
the topology), deferred removal could inadvertently drop the
rport. The code also no longer defers removal via the
default workqueue, instead opting for use of the driver's
own DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The patch below "fixes" calculation of the virt_addr for the AUTO_REQSENSE
case. I put "fixes" in quotes because the real fix would be to completely
remove it, but that's beyond the scope of this patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New versions of the Power5 firmware can send a "re-enable" message to
the virtual scsi adapter. This fix makes us handle the message
correctly. Without it, the driver goes catatonic and the system crashes
unpleasantly.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes the following sparse warnings:
drivers/char/drm/via_dmablit.c:111:35: warning: Using plain integer as NULL pointer
drivers/char/drm/via_dmablit.c:584:23: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Fix CMDBUFFER path, add heap destroy and flesh out sarea for rotation
(Tungsten Graphics)
From: Alan Hourihane <alanh@tungstengraphics.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
From: Nick Piggin <npiggin@suse.de>
Allocate a compound page for the user mapping instead of tweaking the page
refcounts.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
From: Randy Dunlap <rdunlap@xenotime.net>
Use NULL instead of 0 (sparse warnings):
drivers/char/drm/ati_pcigart.c:64:10: warning: Using plain integer as NULL
pointer
drivers/char/drm/ati_pcigart.c:130:21: warning: Using plain integer as NULL
pointer
drivers/char/drm/ati_pcigart.c:171:14: warning: Using plain integer as NULL
pointer
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
From: Brice Goglin <Brice.Goglin@ens-lyon.org>
Now that Xorg 6.9/7.0 has been released, DRI is supported on more Radeon
cards without ATI proprietary drivers. I got my X300 to work without
problem. But, another Radeon X600 required to add its PCI ids to the
Radeon driver. Patch is attached.
I can't be sure about the "CHIP_RV350", I copied it from the X300 entry
(from http://dri.freedesktop.org/wiki/ATIRadeon, X600 is a rv380 chip while
X300 is a rv370). But, at least it works now.
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
From: Luiz Fernando Capitulino <lcapitulino@mandriva.com.br>
drivers/char/drm/radeon_cp.c:1643:31: warning: Using plain integer as NULL
pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
On my latest laptop, I've had occasional PHY dead on wakeup from
sleep... the PHY would be totally unresponsive even to toggling the hard
reset line until the machine is powered down... Looking closely at the
code, I found some possible issues in the way we setup the MDIO lines
during suspend along with slight divergences from what Darwin does when
resetting it that may explain the problem. That patch change these and
the problem appear to be gone for me at least... I also fixed an mdelay
-> msleep while I was at it to the pmac feature code that is called
when toggling the PHY reset line since sungem doesn't call it in an
atomic context anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>b
Signed-off-by: David S. Miller <davem@davemloft.net>
Update version to 1.4.31 and add 2006 copyright.
Skip the last digit when reporting the firmware version.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance the ethtool loopback test with PHY loopback test.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add workaround for a hardware interrupt issue. When using INTA,
unmasking of the interrupt and the tag update should be done
separately to avoid some spurious interrupts,
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix TCP/UDP checksum verification. Use status bits in the buffer
descriptor instead of the checksum value to verify rx checksum.
Using the checksum value will be incorrect if the UDP packet has
zero in the UDP checksum field.
Firmware update required for this fix.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some misc. fixes for WoL, 5708 B1, and a typo '=' instead of '=='.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve handshake with bootcode with the following changes:
1. Increase timeout to 100msec and use msleep instead of udelay.
2. Add more error checking for timeouts and errors.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always set up the device to strip incoming VLAN tags when ASF is
enabled. ASF firmware will not parse packets correctly if VLAN tags
are not stripped.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the documentation error for 'SERIAL_8250' in
drivers/serial/Kconfig
Signed-off-by: Timothy Charles McGrath <tmHikaru@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up some of the messages printed by the superio driver
by defining a prefix instead of duplicating it in every message.
Also some small coding style cleanups.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Define a chassis_power_off routine that machines which have a way
to turn off the power supply can hook into. Formerly they were
using pm_power_off, which is now being used by generic code. Make
lasi.c use chassis_power_off instead of pm_power_off.
Note, all machines need to call machine_power_off so that the
switch can power off the machine, though halt -p may not necessarily
be able to work properly on the machine.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
pdc_stable v0.22, changes since v0.10:
o renamed root subsystem from 'pdc' to 'stable'
o split 'info' into several files, one per PDC field
o implemented 'autoboot' and 'autosearch' write calls to toggle
these flags
o grant read permission to all users on "safe" files
o more code cleanup (removed duplicate code)
o avoid bad stable storage clobbering by write locking critical sections
o print consistent data as well
o SMP cleanups
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Helge,
o Convert a bunch of kmalloc/memset uses to kzalloc.
o pci.c: Add some __read_mostly annotations.
o pci.c: Move constant pci_post_reset_delay to asm/pci.h
o grfioctl.h: Add A4450A to comment of CRT_ID_VISUALIZE_EG.
o Add some consts to perf.c/perf_images.h
Matthew,
o sticore.c: Add some consts to suppress compile warnings.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Same reasoning as commit 747c8a5594
but this time we're making uart_port flags a bitwise type - not
all of these flags correspond with the old ASYNC_ flags, so there
is the possibility for bugs if the wrong ASYNC_* constants are
used. Always use UPF_* constants for uart_port->flags.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mthca_create_ah() includes the port number in the GID index. The reverse
needs to be done in mthca_read_ah().
Noted by Hal Rosenstock.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The functionality UPF_BOOT_ONLYMCA provided has been replaced by
the 8250_mca module, which only registers MCA ports if MCA is
present.
UPF_AUTOPROBE has no functional effect - in fact, it's never
tested. Only ibmasm set the flag.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch resolves most of the problems with an SMP serial console race
with output via the tty path. At the end of the serial console print we
force enable the tx int in case we clobbered the tx interrupt status
racing between the console and tty output. That way the extra tx
interrupt causes the transmit path to restart not hang.
It also makes the serial console printk use the FIFO. This is neccessary
because some remote management devices fake serial console with FIFO and
are confused into sending one packet per character over ethernet when we
stall rather than filling the FIFO.
In order to preserve existing reliability semantics the function waits
for the serial queue to completely empty before returning.
Both of these problems were identified by a Red Hat partner.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added 2006 copyright.
At SuSE's suggestion, enabled all error messages
without enabling function tracing, ie with CONFIG_ACPI_DEBUG=n
Replaced all instances of the ACPI_DEBUG_PRINT macro invoked at
the ACPI_DB_ERROR and ACPI_DB_WARN debug levels with
the ACPI_REPORT_ERROR and ACPI_REPORT_WARNING macros,
respectively. This preserves all error and warning messages
in the non-debug version of the ACPICA code (this has been
referred to as the "debug lite" option.) Over 200 cases
were converted to create a total of over 380 error/warning
messages across the ACPICA code. This increases the code
and data size of the default non-debug version by about 13K.
Added ACPI_NO_ERROR_MESSAGES flag to enable deleting all messages.
The size of the debug version remains about the same.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rather than tweaking acpi_walk_resource() again not return end tags,
modify the pnpacpi code to ignore them.
The pnpacpi resource type switch statements now include all known
types in the order that they're defined -- so it is easy to see
what is not implemented. The code will squawk only if it sees
a truly undefined type.
Signed-off-by: Len Brown <len.brown@intel.com>
Here's a very small diff for 945GM support for agpgart.
Patch against 2.6.15.
From: Alan Hourihane <alanh@fairlite.demon.co.uk>
Signed-off-by: Dave Jones <davej@redhat.com>
There's no need to have request_irq followed by set_irq_type.
Just use request_irq with the appropriate SA_TRIGGER flags.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
some driver clean ups, and a re-posting of changes that are needed
to match the updated TPS.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a subset of the bluesmoke project core code, stripped of the NMI work
which isn't ready to merge and some of the "interesting" proc functionality
that needs reworking or just has no place in kernel. It requires no core
kernel changes except the added scrub functions already posted.
The goal is to merge further functionality only after the core code is
accepted and proven in the base kernel, and only at the point the upstream
extras are really ready to merge.
From: doug thompson <norsk5@xmission.com>
This converts EDAC to sysfs and is the final chunk neccessary before EDAC
has a stable user space API and can be considered for submission into the
base kernel.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EDAC requires a way to scrub memory if an ECC error is found and the chipset
does not do the work automatically. That means rewriting memory locations
atomically with respect to all CPUs _and_ bus masters. That means we can't
use atomic_add(foo, 0) as it gets optimised for non-SMP
This adds a function to include/asm-foo/atomic.h for the platforms currently
supported which implements a scrub of a mapped block.
It also adjusts a few other files include order where atomic.h is included
before types.h as this now causes an error as atomic_scrub uses u32.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
*) mark as "EXPERIMENTAL" various items that either aren't very stable or
that are actively crashing the setup of users which don't really need them
(i.e. HIGHMEM and 3-level pagetables on x86 - nobody needs either,
everybody reports "I'm using it and getting trouble").
*) move net/Kconfig near to the rest of network configurations, and
drivers/block/Kconfig near "Block layer" submenu.
*) it's useless and doesn't work well to force NETDEVICES on and to disable
the prompt like it's done. Better remove the attempt, and change that to a
simple "default y if UML".
*) drop the warning about "report problems about HPPFS" - it's redundant
anyway, as that's the usual procedure, and HPPFS users are especially
technical (i.e. they know reporting bugs is _good_).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix incorrect variable size used to hold register value. This bug might
wipe out a portion of the TCR value when setting the interface options.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Eddie C. Dost <ecd@brainaid.de>
I have the following patch for serial console over the RSC
(remote system controller) on my E250 machine. It basically adds
support for input-device=rsc and output-device=rsc from OBP, and
allows 115200,8,n,1,- serial mode setting.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Andrew Victor
This patch fixes two small issues with 2.6.15-git12.
1) Corrected major/minor numbers for ttyAT devices in the KConfig help.
(Patch from Karl Olsen)
2) tty->flip.count has been removed.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove page refcount manipulations from cassini driver by using
another field in struct page. Needed for lockless pagecache.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the cpufreq code play nicely with the mutex debugging code: don't free a
held mutex.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
This one fell through the automation at first because it initializes the
semaphore to locked, but that's easily remedied
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Dave Jones <davej@redhat.com>
drivers/cpufreq/cpufreq.c | 37 +++++++++++++++++++------------------
include/linux/cpufreq.h | 3 ++-
2 files changed, 21 insertions(+), 19 deletions(-)
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
in attempting to not send the "prefetch" patch, we broke the receive code,
this patch fixes that issue.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Eric Sesterhenn / snakebyte
Alan Stern
Olav Kongas
Greg Kroah-Hartman
David Brownell
Clemens Ladisch
Vojtech Pavlik
Andrew Morton
matthieu castet
Arjan van de Ven
Duncan Sands
Luca Risolia
Craig Shelley
Denis MONTERRAT
Martin Gingras
Juergen Schindele
David Hollis
Alexandre Duret-Lutz
Oliver Neukum
Oliver Neukum
Matthew Dharm
Henk
Rui Santos
Wouter Paesen
Ian Abbott
Louis Nyffenegger
Pete Zaitcev
David S. Miller
Linus Torvalds
Jack Hammer
Moore, Eric
Christoph Hellwig
Christoph Hellwig
Hannes Reinecke
James Bottomley
Michael Reed
Ingo Molnar
Daniel Drake
Jeff Garzik
Bob Moore
Ben Collins
Dmitry Torokhov
Roland Dreier
Michael S. Tsirkin
Adrian Bunk
Zhu Yi
Jens Axboe
Zinx Verituse
Kimball Murray
Alexey Dobriyan
Alessandro Zummo
Sumant Patro
Len Brown
Valdis.Kletnieks@vt.edu
Thomas Renninger
Dale Farnsworth
Paolo Galtieri
Ananda Raju
Stephen Hemminger
brking@us.ibm.com
Lucas Correia Villa Real
Russell King
andrew.vasquez@qlogic.com
Guennadi Liakhovetski
Dave C Boutcher
Jes Sorensen
Dave Airlie
Benjamin Herrenschmidt
Michael Chan
Timothy Charles McGrath
Kyle McMartin
Thibaut VARENE
Helge Deller
Adam Belay
Alan Cox
Alan Hourihane
mark gross
Paolo 'Blaisorblade' Giarrusso
Paul Fulghum
Eddie C. Dost
Andrew Victor
Nick Piggin
Jesse Brandeburg