Add the Intel manufacturer Id.
Tested with Intel JS29F32G08ACMD1(4096 + 224) which is ONFI 2.0 compliant
nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the manufactor ID for SanDisk.
Make preparation for SanDisk SDTNRGAMA-008G.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Assume that:
tmp = ((extid >> 2) & 0x04) | (extid & 0x03));
From the K9LCG08U0B's datasheet, we know that:
the oob size is 640 when tmp is 6;
the oob size is 1024 when tmp is 7;
Signed-off-by: Huang Shijie <b32955@freescale.com>
[Brian: fixed compile issue]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds support for devices with 2048B page sizes and
4-bit ECC strength requirements. This is achieved by enabling the BCH
ECC engine, which provides a higher strength: 16-bit over 2048 bytes.
Additionally, add a proper ECC layout to model the controller's view
of the device (where 'U' means unused and 'B' is the bad block marker):
----------------------------------------------------
| 2048B data | B | B | 30B spare | 30B ECC | U | U |
----------------------------------------------------
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
[Brian: updated with Ezequiel's patch description]
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
commit 3487a63955 ("drivers: mtd: m25p80: add
quad read support") in -next added both the 3-byte OPCODE_QUAD_READ and the
4-byte OPCODE_QUAD_READ_4B, but incorrectly uses OPCODE_QUAD_READ for both
3-byte and 4-byte addressing.
Use OPCODE_QUAD_READ_4B in the 4-byte case to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
According to the Open NAND Flash Interface Specification (ONFI) Revision
3.1 "Parameters are always transferred on the lower 8-bits of the data
bus." for the Get Features and Set Features commands.
So using read_buf and write_buf is wrong for 16-bit wide nand chips as
they use I/O[15:0]. The Get Features command is easily fixed using 4
times the read_byte callback. For Set Features implement a new
overwritable callback "write_byte". Still I expect the default to work
just fine for all controllers and making it overwriteable was just done
for symmetry.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[Brian: fixed warning]
Tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Micron provides READ RETRY support via the ONFI vendor-specific
parameter block (to indicate how many read-retry modes are available)
and the ONFI {GET,SET}_FEATURES commands with a vendor-specific feature
address (to support reading/switching the current read-retry mode).
The recommended sequence is as follows:
1. Perform PAGE_READ operation
2. If no ECC error, we are done
3. Run SET_FEATURES with feature address 89h, mode 1
4. Retry PAGE_READ operation
5. If ECC error and there are remaining supported modes, increment the
mode and return to step 3. Otherwise, this is a true ECC error.
6. Run SET_FEATURES with feature address 89h, mode 0, to return to the
default state.
This patch implements the chip->setup_read_retry() callback for
Micron and fills in the chip->read_retries.
Tested on Micron MT29F32G08CBADA, which supports 8 read-retry modes.
The Micron vendor-specific table was checked against the datasheets for
the following Micron NAND:
Needs retry Cell-type Part number Vendor revision Byte 180
----------- --------- ---------------- --------------- ------------
No SLC MT29F16G08ABABA 1 Reserved (0)
No MLC MT29F32G08CBABA 1 Reserved (0)
No SLC MT29F1G08AACWP 1 0
Yes MLC MT29F32G08CBADA 1 08h
Yes MLC MT29F64G08CBABA 2 08h
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Modern MLC (and even SLC?) NAND can experience a large number of
bitflips (beyond the recommended correctability capacity) due to drifts
in the voltage threshold (Vt). These bitflips can cause ECC errors to
occur well within the expected lifetime of the flash. To account for
this, some manufacturers provide a mechanism for shifting the Vt
threshold after a corrupted read.
The generic pattern seems to be that a particular flash has N read retry
modes (where N = 0, traditionally), and after an ECC failure, the host
should reconfigure the flash to use the next available mode, then retry
the read operation. This process repeats until all bitfips can be
corrected or until the host has tried all available retry modes.
This patch adds the infrastructure support for a
vendor-specific/flash-specific callback, used for setting the read-retry
mode (i.e., voltage threshold).
For now, this patch always returns the flash to mode 0 (the default
mode) after a successful read-retry, according to the flowchart found in
Micron's datasheets. This may need to change in the future if it is
determined that eventually, mode 0 is insufficient for the majority of
the flash cells (and so for performance reasons, we should leave the
flash in mode 1, 2, etc.).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
ECC failures can be tracked at the page level, not the do_read_ops level
(i.e., a potentially multi-page transaction).
This helps prepare for READ RETRY support.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Now that the driver can support the Armada 370/XP SoC NAND controller,
add the devicetree compatible string, enabling its use.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
after device tree based clock lookup became available, the NAND
flash driver need no longer use the previous global "nfc_clk" name,
but should use the "ipg" clock name specific to the OF node
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch kills the NAND_MAX_PAGESIZE/NAND_MAX_OOBSIZE by the following
way:
1.) change the @buf field of nand_buf{} from an array to a pointer.
also remove the DENALI_BUF_SIZE macro.
2.) Before we call the nand_scan_ident, we allocate a temporary buffer
whose size is PAGE_SIZE.
3.) After we finish the nand_scan_ident, we have already getten the
page size and oob size. We will allocate the right buffer size
again.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We kill the NAND_MAX_PAGESIZE/NAND_MAX_OOBSIZE by the following way:
1.) Before we call the nand_scan_ident, we allocate a temporary buffer
whose size is PAGE_SIZE.
2.) After we finish the nand_scan_ident, we have already getten the
page size and oob size. We will allocate the right buffer size
again.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtd.name is assigned to IFC NAND physical address. Assignment type is u32.
It is not providing correct physical address of IFC NAND.
Update assignment type to u64.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch assigned the type->name to mtd->name when mtd->name is
NULL in function "find_full_id_nand".
mtd->name is NULL may cause some problem.
Signed-off-by: Cai Zhiyong <caizhiyong@huawei.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
commit 93115b7fa8 ("mtd: onenand/samsung: make regs-onenand.h file local")
moved the file to the current location but forgot to remove the pointer to
its previous location. Clean it up.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The kernel already has this information, and individual drivers
shouldn't duplicate that. This also eliminates the use of __DATE__ and
__TIME__, which make the build non-deterministic.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nor_erase_prepare() will be called before erase a NOR flash, it will program '0'
into a block to mark this block. But program data into a erasure interrupted block
can cause program timtout(several minutes at most) error, could impact other
operation on NOR flash. So UBIFS can read this block first to avoid unneeded
program operation.
This patch try to put read operation at head of write operation in
nor_erase_prepare(), read out the data.
If the data is already corrupt, then no need to program any data into this block,
just go to erase this block.
This patch is validated on Micron NOR flash, part number is：JS28F512M29EWHA
Signed-off-by: Qi Wang <qiwang@micron.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Some devices (like WNDR3700v3) have board_data without MPFR magic, some
extra header or extra NVRAM around 0x100. In such case we have to look
for another magic which is BD 0B 0D BD (BD probably stands for Board
Data). It's located "far far away", so instead of extending buffer add
another mtd_read.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some devices have even nicer-to-recognize CFE thanks to the magic.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Make this option a hidden one and get a cleaner configuration.
This option just selects a common infrastructure for MTD-based devices
to expose a block interface. There is no point in allowing a separate
enable/disable.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
[Brian: keep symbol as tristate]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fixes this sparse warning:
CHECK drivers/mtd/onenand/generic.c
drivers/mtd/onenand/generic.c:61:62: warning: Using plain integer as NULL pointer
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The omap_{read,write}_buf{8,16}() functions are identical to the default
nand_base versions. Just let nand_base assign them in the
NAND_OMAP_POLLED case.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Pekon Gupta <pekon@ti.com>
We shouldn't try to allocate a resource until we're sure the
of_property_read_u64() call didn't fail. This is especially important if
we use this code for both CONFIG_OF and !CONFIG_OF builds, since
of_property_read_u64() will always return -ENOSYS for !CONFIG_OF.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_warn() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull ARM fixes from Russell King:
"Another set of small fixes for ARM, covering various areas.
Laura fixed a long standing issue with virt_addr_valid() failing to
handle holes in memory. Steve found a problem with dcache flushing
for compound pages. I fixed another bug in footbridge stuff causing
time to tick slowly, and also a problem with the AES code which can
cause linker errors.
A patch from Rob which fixes Xen problems induced by a lack of
consistency in our naming of ioremap_cache() - which thankfully has
very few users"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7933/1: rename ioremap_cached to ioremap_cache
ARM: fix "bad mode in ... handler" message for undefined instructions
CRYPTO: Fix more AES build errors
ARM: 7931/1: Correct virt_addr_valid
ARM: 7923/1: mm: fix dcache flush logic for compound high pages
ARM: fix footbridge clockevent device
ioremap_cache is more aligned with other architectures.
There are only 2 users of this in the kernel: pxa2xx-flash and Xen.
This fixes Xen build failures on arm64:
drivers/tty/hvc/hvc_xen.c:233:2: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/grant-table.c:1174:3: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/xenbus/xenbus_probe.c:778:4: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_kzalloc() to make cleanup paths simpler. Also, checking
return value of devm_kzalloc() is added in order to check if the
allocation succeded.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In order to avoid code duplication, let's consolidate the ECC setting
for all SoC variants. Such decision is based on page size and ECC
strength requirements.
Also, provide a default value for the case where such ECC information
is not provided (non-ONFI devices).
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently, we have two different cmdfunc's implementations:
one for PXA3xx SoC variant and one for Armada 370/XP SoC variant.
The former is the legacy one, typically constrained to devices
with page sizes smaller or equal to the controller's FIFO buffer.
On the other side, the latter _only_ supports the so-called extended
command semantics, which allow to handle devices with larger
page sizes (4 KiB, 8 KiB, ...).
This means we currently don't support devices with smaller pages on the
A370/XP SoC. Fix it by first renaming the cmdfuncs variants, and then
make the choice based on device page size (and SoC variant), rather than
SoC variant alone.
While at it, add a check for page size, to make sure we don't allow larger
pages sizes on the PXA3xx variant.
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently the driver assumes all commands will eventually trigger a RnB
transition, and thus a "device is ready" IRQ.
This assumption means that on every issued command, the dev_ready completion
handler is init'ed and the need_wait flag is set.
However this is incorrect: some commands (such as NAND_CMD_STATUS) don't
make the device 'busy' and thus a RnB transition never occurs.
Given, the NAND core never calls waitfunc() after such commands, this
is not a problem.
Therefore, it's possible to only clear the need_wait flag on every command
that is started.
This fixes a current bug that can be reproduced on PXA boards by writing
blank (all 0xff'ed) to a page:
1. The kernel issues NAND_CMD_STATUS and sets need_wait=1. The flag
won't be cleared for this command since no RnB transition is
involved.
2. NAND_CMD_PAGEPROG is issued but since the data is blank, the driver
decides not to execute the command (and no IRQ activity is
involved).
3. The NAND core calls waitfunc() and waits for the dev_ready
completion, which will never end since the device _is_ already ready.
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch marks the function is_erased() as static in denali.c because
it is not used outside this file.
This patch elimiates the following warning in nand/denali.c:
drivers/mtd/nand/denali.c:900:6: warning: no previous prototype for ‘is_erased’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch marks the functions do_write_buffer() and do_erase_oneblock()
as static because because they are not used outside this file. It also
removes the unused function word_program() in lpddr/lpddr_cmds.c.
Thus, it also removes the following warnings in lpddr/lpddr_cmds.c:
drivers/mtd/lpddr/lpddr_cmds.c:391:5: warning: no previous prototype for ‘do_write_buffer’ [-Wmissing-prototypes]
drivers/mtd/lpddr/lpddr_cmds.c:472:5: warning: no previous prototype for ‘do_erase_oneblock’ [-Wmissing-prototypes]
drivers/mtd/lpddr/lpddr_cmds.c:751:5: warning: no previous prototype for ‘word_program’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver doesn't need its own custom chip->write_page callback; the
only "custom" requirement is that this driver does not support subpage
writes, which we can avoid using the NAND_NO_SUBPAGE_WRITE flag. With
NAND_NO_SUBPAGE_WRITE, the default routine (nand_write_page()) should
perform the equivalent operations.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Tested-by: Roland Stigge <stigge@antcom.de>
The TI AEMIF driver registers are used to setup timings for each chip
select. The same registers range is used to setup NAND settings.
The AEMIF and NAND drivers not use the same registers in this range.
In case with TI AEMIF driver, the memory address range is requested
already by AEMIF, so we cannot request it twice, just ioremap.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Keystone arch has compatible nand device, so reuse it.
In case with Keystone it depends on TI_AEMIF because AEMIF
driver is responsible to set timings.
See http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The properties davinci-ecc-mode, davinci-nand-use-bbt, davinci-nand-buswidth
are MTD generic. Correct names for them are: nand-ecc-mode, nand-on-flash-bbt,
nand-bus-width accordingly. So rename them in dts and documentation.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is not needed to use a lot of names for err handling.
It complicates code support and reading.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The property "ti,davinci-chipselect" is required. So we have to check
if it is set.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case when memory allocation is failed the driver should return
ENOMEM instead of ENODEV.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When kernel is booted using DT, there is no guarantee that Davinci
NAND device has been created already at the time when driver init
function is executed. Therefore, platform_driver_probe() can't be used
because this may result the Davinci NAND driver will never be probed.
The driver probing has to be made with core mechanism.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
clock source is prepared and enabled by clk_prepare_enable() in
mxcnd_probe() function, but no disable/unprepare in mxcnd_remove().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since the of_mtd header provides dummy stubs for !CONFIG_OF, it's safe
to remove the #ifdef CONFIG_OF. Build tested only.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cast pointers to uintptr_t instead of unsigned int. This fixes warnings
on platforms where pointers have a different size than int.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
register_mtd_parser never fails; hence make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
deregister_mtd_parser never fails; hence make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a nice "nand:" prefix to all pr_xxx() messages. This allows
to get rid of the "NAND" words in messages, given the context
is already given by the prefix.
Remove the __func__ report from messages where it's not needed and refactor
the device detection messages to show itself in several lines.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using the IS_ENABLED() macro can make the code shorter and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use new ATTRIBUTE_GROUPS macro to declare attribute groups.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for Micron m25px16 spi flash chip.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ecc_stats.corrected count variable will already be incremented in
the above framework-layer just after this callback.
Cc: stable@vger.kernel.org # 2.6.36+
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The devm_request_irq function allocates irq that is released
when a driver detaches. Thus, there is no reason to explicitly
call devm_free_irq in probe or remove functions.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There are pr_err and dev_err in the gpmi driver now.
It makes people confused.
This patch changes all the pr_err to dev_err except the one
in the gpmi_reset_block(). We also remove the unnecessary
print for OOM message.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The error messages for the failure of dmaengine_prep_slave_sg are
not necessary, this patch removes all these pr_err, and returns with
the proper error code -EINVAL, not -1.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds request_mem_region() prior ioremap() for diskonchip
driver. This will allow to check if memory region is occupied by any
other device, for example in case if we have memory region for several
optional devices and only one device can be used at once.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_request_irq to simplify the code.
Also remove the unused fields of structure resources{}.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the devm_ioremap_resource to simplify the code.
[Note: as a side effect, this adds a missing call to request_memory().]
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The gpmi_nfc_* is the legacy name. In order to avoid the confusion,
The patch renames the gpmi_nfc_* functions to gpmi_nand_*.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We do not use the chip->oob_poi in the mx23_write_transcription_stamp.
So remove the unused line.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We do not scan the BBT after we call the gpmi_pre_bbt_scan,
so it has lost the meaning of existence.
This patch merges this function into gpmi_init_last, and delete it.
This patch does not change any logic.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The local array feature[] is in the stack. We can see the warning
when we enable the CONFIG_DMA_API_DEBUG:
----------------------------------------------------------
WARNING: at lib/dma-debug.c:950 check_for_stack+0xac/0xf8()
gpmi-nand 112000.gpmi-nand: DMA-API: device driver maps memory fromstack [addr=dc05be34]
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.17-16851-g2414a73 #1324
[<80014cbc>] (unwind_backtrace+0x0/0x138) from [<8001251c>] (show_stack+0x10/0x14)
[<8001251c>] (show_stack+0x10/0x14) from [<8002699c>] (warn_slowpath_common+0x4c/0x68)
[<8002699c>] (warn_slowpath_common+0x4c/0x68) from [<80026a4c>] (warn_slowpath_fmt+0x30/0x40)
[<80026a4c>] (warn_slowpath_fmt+0x30/0x40) from [<8028e2f8>] (check_for_stack+0xac/0xf8)
[<8028e2f8>] (check_for_stack+0xac/0xf8) from [<8028e438>] (debug_dma_map_sg+0xf4/0x188)
[<8028e438>] (debug_dma_map_sg+0xf4/0x188) from [<803968d0>] (prepare_data_dma+0xb8/0x1a8)
[<803968d0>] (prepare_data_dma+0xb8/0x1a8) from [<80397b20>] (gpmi_send_data+0x84/0xfc)
[<80397b20>] (gpmi_send_data+0x84/0xfc) from [<8038c2b4>] (nand_onfi_set_features+0x50/0x74)
[<8038c2b4>] (nand_onfi_set_features+0x50/0x74) from [<80397198>] (gpmi_extra_init+0x90/0x170)
[<80397198>] (gpmi_extra_init+0x90/0x170) from [<8039520c>] (gpmi_nand_probe+0x2f8/0xb3c)
[<8039520c>] (gpmi_nand_probe+0x2f8/0xb3c) from [<8031b974>] (platform_drv_probe+0x18/0x1c)
----------------------------------------------------------
The patch uses the kzalloc to allocate the buffer, and free it when
we do not use it anymore.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Armada BCH configuration in this driver uses one of the two
following ECC schemes:
16-bit correction per 2048 bytes
16-bit correction per 1024 bytes
These are sufficient for mapping to the 4-bit per 512-bytes and 8-bit
per 512-bytes (respectively) minimum correctability requirements of many
common NAND.
The current code only checks for the required strength (4-bit or 8-bit)
without checking the ECC step size that is associated with that strength
(and simply assumes it is 512). While that is often a safe assumption to
make, let's make it explicit, since we have that information.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
This commit extends the ECC correctable error detection to include
ECC BCH errors. The number of BCH correctable errors can be any up to 16,
and the actual value is exposed in the NDSR register.
Therefore, we change some symbol names to refer to correctable or
uncorrectable (instead of single-bit or double-bit as it was in the
Hamming case) and while at it, cleanup the detection code slightly.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds write support for large pages (4 KiB, 8 KiB).
Such support is implemented by issuing a multiple command sequence,
transfering a set of 2 KiB chunks per transaction.
The splitted command sequence requires to send the SEQIN command
independently of the PAGEPROG command and therefore it's set as
an execution command.
Since PAGEPROG enables ECC, each 2 KiB chunk of data is written
together with ECC code at a controller-fixed location within
the flash page.
Currently, only devices with a 4 KiB page size has been tested.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As preparation work to fully support large pages, this commit adds
the initial infrastructure to support splitted (aka chunked) I/O
operation. This commit adds support for read, and follow-up patches
will add write support.
When a read (aka READ0) command is issued, the driver loops issuing
the same command until all the requested data is transfered, changing
the 'extended' command field as needed.
For instance, if the driver is required to read a 4 KiB page, using a
chunk size of 2 KiB, the transaction is splitted in:
1. Monolithic read, first 2 KiB page chunk is read
2. Last naked read, second and last 2KiB page chunk is read
If ECC is enabled it is calculated on each chunk transfered and added
at a controller-fixed location after the data chunk that must be
spare area.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In preparation to support multiple (aka chunked, aka splitted)
page I/O, this commit adds 'data_buff_pos' and 'oob_buff_pos' fields
to keep track of where the next read (or write) should be done.
This will allow multiple calls to handle_data_pio() to continue
the read (or write) operation.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds support page programming with a non-zero "column"
address setting. This is important to support OOB writing, through
command sequences such as:
cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, ofs);
write_buf(mtd, oob_buf, 6);
cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
To allow future support of multiple page reading/writing, move the data
buffer clean out of prepare_set_command().
This is done to prevent the data buffer from being cleaned on every command
preparation, when a multiple command sequence is implemented to read/write
pages larger than the FIFO size (2 KiB).
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit splits the prepare_command_pool() function into two
stages: prepare_start_command() / prepare_set_command().
This is a preparation patch without any functionality changes,
and is meant to allow support for multiple page reading/writing
operations.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
READ0 and READOOB command preparation has a falltrough to SEQIN
case, where the command address is specified.
This is certainly confusing and makes the code less readable with
no added value. Let's remove it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Let's simplify the code by first introducing a helper function
to set the page address, as done by the READ0, READOOB and SEQIN
commands.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Command buffer #3 is not properly cleared and it keeps the last
set value. Fix this by clearing when a command is setup.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds the BCH ECC support available in NFCv2 controller.
Depending on the detected required strength the respective ECC layout
is selected.
This commit adds an empty ECC layout, since support to access large
pages is first required. Once that support is added, a proper ECC
layout will be added as well.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for flash-based bad block table using Marvell's
custom in-flash bad block table layout. The support is enabled
a 'flash_bbt' platform data or device tree parameter.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In pxa3xx_nand_sensing() instead of simply using info->is_ready
after issuing a command, the correct way of checking is to wait
for the device to be ready through the chip's waitfunc().
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The expected behavior of the waitfunc() NAND chip call is to wait
for the device to be READY (this is a standard chip line).
However, the current implementation does almost nothing, which opens
the possibility of issuing a command to a non-ready device.
Fix this by adding a new completion to wait for the ready event to arrive.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a comment clarifying the use of pxa3xx_set_datasize() which is only
applicable on data read/write commands (i.e. commands with a data cycle,
such as READID, READ0, STATUS, etc.)
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There's no need to privately store the device page size as it's
available in mtd structure field mtd->writesize.
Also, this removes the hardcoded page size value, leaving the
auto-detected value only.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Introduce a fifo_size field to represent the size of the controller's
FIFO buffer, and use it to distinguish that size from the amount
of data bytes to be read from the FIFO.
This is important to support devices with pages larger than the
controller's internal FIFO, that need to read the pages in FIFO-sized
chunks.
In particular, the current code is at least confusing, for it mixes
all the different sizes involved: FIFO size, page size and data size.
This commit starts the cleaning by removing the info->page_size field
that is not currently used. The host->page_size field should also
be removed and use always mtd->writesize instead. Follow up commits
will clean this up.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Whenever possible, it's always better to use the generic chip->cmdfunc
instead of the internal pxa3xx_nand_cmdfunc().
In this particular case, this will allow to have multiple cmdfunc()
implementations for different SoC variants.
Reviewed-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In order to customize early settings depending on the detected SoC variant,
move the detection to be before the nand_chip struct filling.
In a follow-up patch, this change is needed to detect the variant *before*
the call to alloc_nand_resource(), which allows to set a different cmdfunc()
for each variant.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As per the ecc.read_page() prototype, we must return the maximum number
of bitflips that were corrected on any one region covering an ecc step.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The current driver doesn't support sub-page writing, so report
that to the NAND core.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since we have now support for the NFCv2 controller found on
Armada 370/XP platforms.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Given there's no public specification to this date, and in order
to capture some important details and singularities about the
controller let's document them once and for good.
Cc: linux-doc@vger.kernel.org
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix the following checkpatch warnings:
WARNING: line over 80 characters
#268: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:268:
+ * consecutive reboots. The latter case has not been seen on the MX23 yet,
WARNING: space prohibited before semicolon
#356: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:356:
+ (target.tRHOH_in_ns >= 0) ;
WARNING: space prohibited before semicolon
#1006: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:1006:
+ BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles) ;
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using devm_clk_get() can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In default way, we use the ecc_strength/ecc_step size calculated by ourselves
and use all the OOB area.
This patch adds a new property : "fsl,use-minimum-ecc"
If we enable it, we will firstly try to use the datasheet's minimum required
ECC provided by the MTD layer (the ecc_strength_ds/ecc_step_ds fields
in the nand_chip{}). So we may have free space in the OOB area by using the
minimum ECC, and we may support JFFS2 with some SLC NANDs, such as Micron's
SLC NAND.
If we fail to use the minimum ECC, we will use the legacy method to calculate
the ecc_strength and ecc_step size.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This option does not need to depend in MTD_NAND, for it's enclosed
under it. Also, it's wrong to make it depend in ARCH_OMAP3 only
since the controller is used in a wider range of SoCs.
Instead, just leave the dependency on the OMAP2 driver option.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some flash also support quad read mode. Adding support for quad read
mode in m25p80 for Spansion and Macronix flash.
[Tweaked by Brian]
With this patch, quad-read support will override fast-read and
normal-read, if the SPI controller and flash chip both support it.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This is a cleanup prior to adding quad read support. This will facilitate
easy addition of more read commands check under an enum rather that defining a
separate bool for it.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Richard Weinberger <richard@nod.at>
commit 93115b7fa8 ("mtd: onenand/samsung: make regs-onenand.h file local")
moved the file to the current location but forgot to remove the pointer to
its previous location. Clean it up.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In commit:
commit 62e8b85178
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Fri Oct 4 15:30:38 2013 -0300
mtd: nand: pxa3xx: Allocate data buffer on detected flash size
the way the buffer is allocated was changed: the first READ_ID is issued
with a small kmalloc'ed buffer. Only once the flash page size is detected
the DMA buffers are allocated, and info->use_dma is set.
Currently, if the device detection fails, the driver checks the 'use_dma'
module parameter and tries to release unallocated DMA resources.
Fix this by checking the proper indicator of the DMA allocation, which
is 'info->use_dma'.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This partially reverts c0f3b8643a.
The "armada370-nand" compatible support is not complete, and it was mistake
to add it. Revert it and postpone the support until the infrastructure is
in place.
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
Pull dmaengine changes from Dan
1/ Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
2/ In the course of testing 1/ a collection of enhancements to dmatest
fell out. Notably basic performance statistics, and fixed / enhanced
test control through new module parameters 'run', 'wait', 'noverify',
and 'verbose'. Thanks to Andriy and Linus for their review.
3/ Testing the raid related corner cases of 1/ triggered bugs in the
recently added 16-source operation support in the ioatdma driver.
4/ Some minor fixes / cleanups to mv_xor and ioatdma.
Conflicts:
drivers/dma/dmatest.c
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
* Other general cleanups (removing unused functions, options, variables,
fields; use correct interfaces)
* Fix BUG() for new odd-sized NAND, which report non-power-of-2 dimensions via
ONFI
* Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
* Improve differentiation between SLC and MLC NAND -- this clarifies an ABI
issue regarding the MTD "type" (in sysfs and in ioctl(MEMGETINFO)), where
the MTD_MLCNANDFLASH type was present but inconsistently used
* Extend GPMI NAND to support multi-chip-select NAND for some platforms
* Many improvements to the OMAP2/3 NAND driver, including an expanded DT
binding to bring us closer to mainline support for some OMAP systems
* Fix a deadlock in the error path of the Atmel NAND driver probe
* Correct the error codes from MTD mmap() to conform to POSIX and the Linux
Programmer's Manual. This is an acknowledged change in the MTD ABI, but I
can't imagine somebody relying on the non-standard -ENOSYS error code
specifically. Am I just being unimaginative? :)
* Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
* More? Read the log!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=z5qO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd
Pull MTD changes from Brian Norris:
- Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
- Other general cleanups (removing unused functions, options,
variables, fields; use correct interfaces)
- Fix BUG() for new odd-sized NAND, which report non-power-of-2
dimensions via ONFI
- Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
- Improve differentiation between SLC and MLC NAND -- this clarifies an
ABI issue regarding the MTD "type" (in sysfs and in the MEMGETINFO
ioctl), where the MTD_MLCNANDFLASH type was present but
inconsistently used
- Extend GPMI NAND to support multi-chip-select NAND for some platforms
- Many improvements to the OMAP2/3 NAND driver, including an expanded
DT binding to bring us closer to mainline support for some OMAP
systems
- Fix a deadlock in the error path of the Atmel NAND driver probe
- Correct the error codes from MTD mmap() to conform to POSIX and the
Linux Programmer's Manual. This is an acknowledged change in the MTD
ABI, but I can't imagine somebody relying on the non-standard -ENOSYS
error code specifically. Am I just being unimaginative? :)
- Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
- More? Read the log!
* tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd: (98 commits)
mtd: gpmi: fix the NULL pointer
mtd: gpmi: fix kernel BUG due to racing DMA operations
mtd: mtdchar: return expected errors on mmap() call
mtd: gpmi: only scan two chips for imx6
mtd: gpmi: Use devm_kzalloc()
mtd: atmel_nand: fix bug driver will in a dead lock if no nand detected
mtd: nand: use a local variable to simplify the nand_scan_tail
mtd: nand: remove deprecated IRQF_DISABLED
mtd: dataflash: Say if we find a device we don't support
mtd: nand: omap: fix error return code in omap_nand_probe()
mtd: nand_bbt: kill NAND_BBT_SCANALLPAGES
mtd: m25p80: fixup device removal failure path
mtd: mxc_nand: Include linux/of.h header
mtd: remove duplicated include from mtdcore.c
mtd: m25p80: add support for Macronix mx25l3255e
mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig
mtd: nand: omap: updated devm_xx for all resource allocation and free calls
mtd: nand: omap: use drivers/mtd/nand/nand_bch.c wrapper for BCH ECC instead of lib/bch.c
mtd: nand: omap: clean-up ecc layout for BCH ecc schemes
mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe
...
Pull vfs updates from Al Viro:
"All kinds of stuff this time around; some more notable parts:
- RCU'd vfsmounts handling
- new primitives for coredump handling
- files_lock is gone
- Bruce's delegations handling series
- exportfs fixes
plus misc stuff all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (101 commits)
ecryptfs: ->f_op is never NULL
locks: break delegations on any attribute modification
locks: break delegations on link
locks: break delegations on rename
locks: helper functions for delegation breaking
locks: break delegations on unlink
namei: minor vfs_unlink cleanup
locks: implement delegations
locks: introduce new FL_DELEG lock flag
vfs: take i_mutex on renamed file
vfs: rename I_MUTEX_QUOTA now that it's not used for quotas
vfs: don't use PARENT/CHILD lock classes for non-directories
vfs: pull ext4's double-i_mutex-locking into common code
exportfs: fix quadratic behavior in filehandle lookup
exportfs: better variable name
exportfs: move most of reconnect_path to helper function
exportfs: eliminate unused "noprogress" counter
exportfs: stop retrying once we race with rename/remove
exportfs: clear DISCONNECTED on all parents sooner
exportfs: more detailed comment for path_reconnect
...
experimental. It looks like it starts getting more users. No significant
changes for the "classical" non-fastmap UBI.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=P8sc
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.13-rc1' of git://git.infradead.org/linux-ubi
Pull UBI changes from Artem Bityutskiy:
"A bunch of fixes for the fastmap feature, which is still new and
rather experimental. It looks like it starts getting more users.
No significant changes for the "classical" non-fastmap UBI"
* tag 'upstream-3.13-rc1' of git://git.infradead.org/linux-ubi:
UBI: Add some asserts to ubi_attach_fastmap()
UBI: Fix memory leak in ubi_attach_fastmap() error path
UBI: simplify image sequence test
UBI: fastmap: fix backward compatibility with image_seq
UBI: Call scan_all() with correct offset in error case
UBI: Fix error path in scan_pool()
UBI: fix refill_wl_user_pool()
The imx23 board will check the fingerprint, so it will call the
mx23_check_transcription_stamp. This function will use @chip->buffers->databuf
as its buffer which is allocated in the nand_scan_tail().
Unfortunately, the mx23_check_transcription_stamp is called before the
nand_scan_tail(). So we will meet a NULL pointer bug:
--------------------------------------------------------------------
[ 1.150000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xd7 (Samsung NAND 4GiB 3,3V 8-bit), 4096MiB, page size: 4096, OOB size: 8
[ 1.160000] Unable to handle kernel NULL pointer dereference at virtual address 000005d0
[ 1.170000] pgd = c0004000
[ 1.170000] [000005d0] *pgd=00000000
[ 1.180000] Internal error: Oops: 5 [#1] ARM
[ 1.180000] Modules linked in:
[ 1.180000] CPU: 0 PID: 1 Comm: swapper Not tainted 3.12.0 #89
[ 1.180000] task: c7440000 ti: c743a000 task.ti: c743a000
[ 1.180000] PC is at memcmp+0x10/0x54
[ 1.180000] LR is at gpmi_nand_probe+0x42c/0x894
[ 1.180000] pc : [<c025fcb0>] lr : [<c02f6a68>] psr: 20000053
[ 1.180000] sp : c743be2c ip : 600000d3 fp : ffffffff
[ 1.180000] r10: 000005d0 r9 : c02f5f08 r8 : 00000000
[ 1.180000] r7 : c75858a8 r6 : c75858a8 r5 : c7585b18 r4 : c7585800
[ 1.180000] r3 : 000005d0 r2 : 00000004 r1 : c05c33e4 r0 : 000005d0
[ 1.180000] Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 1.180000] Control: 0005317f Table: 40004000 DAC: 00000017
[ 1.180000] Process swapper (pid: 1, stack limit = 0xc743a1c0)
--------------------------------------------------------------------
This patch rearrange the init procedure:
Set the NAND_SKIP_BBTSCAN to skip the nand scan firstly, and after we
set the proper settings, we will call the chip->scan_bbt() manually.
Cc: stable@vger.kernel.org # 3.12
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
[1] The gpmi uses the nand_command_lp to issue the commands to NAND chips.
The gpmi issues a DMA operation with gpmi_cmd_ctrl when it handles
a NAND_CMD_NONE control command. So when we read a page(NAND_CMD_READ0)
from the NAND, we may send two DMA operations back-to-back.
If we do not serialize the two DMA operations, we will meet a bug when
1.1) we enable CONFIG_DMA_API_DEBUG, CONFIG_DMADEVICES_DEBUG,
and CONFIG_DEBUG_SG.
1.2) Use the following commands in an UART console and a SSH console:
cmd 1: while true;do dd if=/dev/mtd0 of=/dev/null;done
cmd 1: while true;do dd if=/dev/mmcblk0 of=/dev/null;done
The kernel log shows below:
-----------------------------------------------------------------
kernel BUG at lib/scatterlist.c:28!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
.........................
[<80044a0c>] (__bug+0x18/0x24) from [<80249b74>] (sg_next+0x48/0x4c)
[<80249b74>] (sg_next+0x48/0x4c) from [<80255398>] (debug_dma_unmap_sg+0x170/0x1a4)
[<80255398>] (debug_dma_unmap_sg+0x170/0x1a4) from [<8004af58>] (dma_unmap_sg+0x14/0x6c)
[<8004af58>] (dma_unmap_sg+0x14/0x6c) from [<8027e594>] (mxs_dma_tasklet+0x18/0x1c)
[<8027e594>] (mxs_dma_tasklet+0x18/0x1c) from [<8007d444>] (tasklet_action+0x114/0x164)
-----------------------------------------------------------------
1.3) Assume the two DMA operations is X (first) and Y (second).
The root cause of the bug:
Assume process P issues DMA X, and sleep on the completion
@this->dma_done. X's tasklet callback is dma_irq_callback. It firstly
wake up the process sleeping on the completion @this->dma_done,
and then trid to unmap the scatterlist S. The waked process P will
issue Y in another ARM core. Y initializes S->sg_magic to zero
with sg_init_one(), while dma_irq_callback is unmapping S at the same
time.
See the diagram:
ARM core 0 | ARM core 1
-------------------------------------------------------------
(P issues DMA X, then sleep) --> |
|
(X's tasklet wakes P) --> |
|
| <-- (P begin to issue DMA Y)
|
(X's tasklet unmap the |
scatterlist S with dma_unmap_sg) --> | <-- (Y calls sg_init_one() to init
| scatterlist S)
|
[2] This patch serialize both the X and Y in the following way:
Unmap the DMA scatterlist S firstly, and wake up the process at the end
of the DMA callback, in such a way, Y will be executed after X.
After this patch:
ARM core 0 | ARM core 1
-------------------------------------------------------------
(P issues DMA X, then sleep) --> |
|
(X's tasklet unmap the |
scatterlist S with dma_unmap_sg) --> |
|
(X's tasklet wakes P) --> |
|
| <-- (P begin to issue DMA Y)
|
| <-- (Y calls sg_init_one() to init
| scatterlist S)
|
Cc: stable@vger.kernel.org # 3.2
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
According both to POSIX.1-2008 and Linux Programmer's Manual mmap()
syscall shouldn't return undocumented ENOSYS, this change replaces
the errno with more appropriate ENODEV and EACCESS.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We cannot scan two chips for imx23 and imx28:
imx23: the Ready-Busy1 line is not connected for some board.
imx28: we do not set the pinctrl for Ready-Busy1
So we only scan two chips for imx6.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit b5b4bb3f6a (of: only include prom.h on sparc) removed implicit
includes of of_*.h headers by powerpc's prom.h. Some components were
missed in initial clean-up patch, so add the necessary includes to fix
powerpc builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-ide@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Using devm_kzalloc() can make the code simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In the atmel driver probe function, the code shows like following:
atmel_nand_probe(...) {
...
err_nand_ioremap:
platform_driver_unregister(&atmel_nand_nfc_driver);
return res;
}
If no nand flash detected, the driver probe function will goto
err_nand_ioremap label.
Then platform_driver_unregister() will be called. It will get the
lock of atmel_nand device since it is parent of nfc_device. The
problem is the lock is already hold by atmel_nand_probe itself.
So system will be in a dead lock.
This patch just simply removed to platform_driver_unregister() call.
When atmel_nand driver is quit the platform_driver_unregister() will
be called in atmel_nand_remove().
[Brian: the NAND platform probe really has no business
registering/unregistering another driver; this fixes the deadlock, but
we should follow up the likely racy behavior here with a better
architecture]
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There are too many "chip->ecc" in the nand_scan_tail() which makes the eyes
sore.
This patch uses a local variable "ecc" to replace the "chip->ecc" to
make the code more graceful.
Do the code change with "s/chip->ecc\./ecc->/g" in the nand_scan_tail,
and also change some lines by hand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Ensure that the error message if we identify a flash we don't know how to
talk to is displayed on the console in order to aid diagnostics. While
we're at convert the message to use dev_info() rather than our hand rolled
version of it for consistency.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix to return a negative error code from the error handling case instead
of 0, to more closely match the rest of this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Now that the last user of NAND_BBT_SCANALLPAGES has been removed, let's
kill this peculiar BBT feature flag.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Device removal should fail if MTD unregistration fails.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
A new 32Mbit SPI NOR flash from Macronix. Nothing special.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
With OMAP NAND driver updates, selection of ecc-scheme:
*DT enabled kernel*
depends on ti,nand-ecc-opt and ti,elm-id DT bindings.
*Non DT enabled kernel*
depends on elm_dev and ecc-scheme passed along with platform-data
from board file.
So, selection of ecc-scheme (BCH8 or BCH4) from KConfig can be removed
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
"Managed Device Resource" or devm_xx calls takes care of automatic freeing
of the resource in case of:
- failure during driver probe
- failure during resource allocation
- detaching or unloading of driver module (rmmod)
Reference: Documentation/driver-model/devres.txt
Though OMAP NAND driver handles freeing of resource allocation in most of
the cases, but using devm_xx provides more clean and effortless approach
to handle all such cases.
- simplifies label for exiting probe during error
s/out_release_mem_region/return_error
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
generic frame-work in mtd/nand/nand_bch.c is a wrapper above lib/bch.h which
encapsulates all control information specific to BCH ecc algorithm in software.
Thus this patch:
(1) replace omap specific implementations with equivalent wrapper in nand_bch.c
so that generic code from nand_bch.c is re-used. like;
omap3_correct_data_bch() -> nand_bch_correct_data()
omap3_free_bch() -> nand_bch_free()
(2) replace direct calls to lib/bch.c with wrapper functions defined in nand_bch.c
init_bch() -> nand_bch_init()
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In current implementation omap3_init_bch_tail() is a common function to
define ecc layout for different BCHx ecc schemes.This patch:
(1) removes omap3_init_bch_tail() and defines ecc layout for individual
ecc-schemes along with populating their nand_chip->ecc data in
omap_nand_probe(). This improves the readability and scalability of
code for add new ecc schemes in future.
(2) removes 'struct nand_bbt_descr bb_descrip_flashbased' because default
nand_bbt_descr in nand_bbt.c matches the same (.len=1 for x8 devices).
(3) add the check to see if NAND device has enough OOB/Spare bytes to
store ECC signature of whole page, as defined by ecc-scheme.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
current implementation in omap3_init_bch() has some redundant code like:
(1) omap3_init_bch() re-probes the DT-binding to detect presence of ELM h/w
engine on SoC. And based on that it selects implemetation of ecc-scheme.
However, this is already done as part of GPMC DT parsing.
(2) As omap3_init_bch() serves as common function for configuring all types of
BCHx ecc-schemes, so there are multiple levels of redudant if..then..else
checks while populating nand_chip->ecc.
This patch make following changes to OMAP NAND driver:
(1) removes omap3_init_bch(): each ecc-scheme is individually configured in
omap_nand_probe() there by removing redundant if..then..else checks.
(2) adds is_elm_present(): re-probing of ELM device via DT is not required as
it's done in GPMC driver probe. Thus is_elm_present() just initializes ELM
driver with NAND probe data, when ecc-scheme with h/w based error-detection
is used.
(3) separates out configuration of different flavours of "BCH4" and "BCH8"
ecc-schemes as given in below table
(4) conditionally compiles callbacks implementations of ecc.hwctl(),
ecc.calculate(), ecc.correct() to avoid warning of un-used functions.
+---------------------------------------+---------------+---------------+
| ECC scheme |ECC calculation|Error detection|
+---------------------------------------+---------------+---------------+
|OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH4_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W (lib/bch.c)|
| (needs CONFIG_MTD_NAND_ECC_BCH) | | |
| | | |
|OMAP_ECC_BCH4_CODE_HW |H/W (GPMC) |H/W (ELM) |
| (needs CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id) | | |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W (lib/bch.c)|
| (needs CONFIG_MTD_NAND_ECC_BCH) | | |
| | | |
|OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) |
| (needs CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id) | | |
+---------------------------------------+---------------+---------------+
- 'CONFIG_MTD_NAND_ECC_BCH' is generic KConfig required to build lib/bch.c
which is required for ECC error detection done in software.
(mainly used for legacy platforms which do not have on-chip ELM engine)
- 'CONFIG_MTD_NAND_OMAP_BCH' is OMAP specific Kconfig to detemine presence
on ELM h/w engine on SoC.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch:
- calls nand_scan_ident() using bus-width as passed by DT
- removes double calls to nand_scan_ident(), in case first call fails
then omap_nand_probe just returns error.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It seems like the following commit was never necessary
commit 5f94913795
Author: Shaohui Xie <Shaohui.Xie@freescale.com>
Date: Fri Oct 14 15:49:00 2011 +0800
mtd: m25p80: don't probe device which has status of 'disabled'
because it duplicates the code in of_platform_device_create_pdata()
which ensures that 'disabled' nodes are never instantiated.
Also, drop the __maybe_unused.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: <devicetree@vger.kernel.org>
Remove the compile-time option for FAST_READ, since we have run-time
support for detecting it. This refactors the logic for enabling
fast-read, such that for DT-enabled devices, we honor the
"m25p,fast-read" property but for non-DT devices, we default to using
FAST_READ whenever the flash device supports it.
Normal READ and FAST_READ differ only in the following:
* FAST_READ supports SPI higher clock frequencies [1]
* number of dummy cycles; FAST_READ requires 8 dummy cycles (whereas
READ requires 0) to allow the flash sufficient setup time, even when
running at higher clock speeds
Thus, for flash chips which support FAST_READ, there is otherwise no
limiting reason why we cannot use the FAST_READ opcode instead of READ.
It simply allows the SPI controller to run at higher clock rates. So
theoretically, nobody should be needing the compile-time option anyway.
[1] I have a Spansion S25FL128S datasheet which says:
"The maximum operating clock frequency for the READ command is 50
MHz."
And:
"The maximum operating clock frequency for FAST READ command is 133
MHz."
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FIXME and NOTE have already been fixed (we have FAST_READ support).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch fixes two memory errors:
1. During a probe failure (in mtd_device_parse_register?) the command
buffer would not be freed.
2. The command buffer's size is determined based on the 'fast_read'
boolean, but the assignment of fast_read is made after this
allocation. Thus, the buffer may be allocated "too small".
To fix the first, just switch to the devres version of kzalloc.
To fix the second, increase MAX_CMD_SIZE unconditionally. It's not worth
saving a byte to fiddle around with the conditions here.
This problem was reported by Yuhang Wang a while back.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Yuhang Wang <wangyuhang2014@gmail.com>
Reviewed-by: Sourav Poddar <sourav.poddar@ti.com>
Cc: <stable@vger.kernel.org>
In the imx6, all the ready/busy pins are binding togeter.
So we should always check the ready/busy pin of the chip 0.
In the other word, when the CS1 is enabled, we should also check the
ready/busy of chip 0; if we check the ready/busy of chip 1,
we will get the wrong result.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some nand chip has two DIEs in a single chip, such as Micron MT29F32G08QAA.
Each die has its own chip select pin, so this chip acts as two nand
chips.
If we only scan one chip, we may find that we only get 2G for this chip,
but in actually, this chip's size is 4G.
So scan two chips by default.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We only have one DMA channel : the channel 0.
Use DMA channel 0 to access all the nand chips.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Decouple the chip select from the DMA channel, we use the DMA channel 0
to accecc all the nand devices.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
as per controller description,
"While programming a NAND flash, status read should never skipped.
Because it may happen that a new command is issued to the NAND Flash,
even when the device has not yet finished processing the previous request.
This may result in unpredictable behaviour."
IFC controller never polls for R/B signal after command send. It just return
control to software. This behaviour may not occur with NAND flash access.
because new commands are sent after polling R/B signal. But it may happen
in scenario where GPCM-ASIC and NAND flash device are working simultaneously.
Update the controller driver to take care of this requirement
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current IFC driver supports till 4K page size NAND flash.
Add support of 8K Page size NAND flash
- Add nand_ecclayout for 4 bit & 8 bit ecc
- Defines constants
- also fix ecc.strength for 8bit ecc of 8K page size NAND
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch moves the char and block major number definitions
to major.h to be with the rest of the major numbers.
While doing this, include major.h in the files that need it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
A new type of partition with magic FCTY was found on Huawei E970:
46 43 54 59 4b 51 37 4e 41 42 31 38 41 32 39 30 |FCTYKQ7NAB18A290|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Most of the bcm47xx devices use TRX format for storing kernel and some
partition like Squashfs or JFFS2. This is pretty flexible solution, CFE
(the bootloader) just writes (and later boots) TRX at some hardcoded
place and paritions can vary in the size.
However some devices don't use TRX format. Very recently we have
discovered ZTE H218N that has kernel and rootfs partitions at some
"random" places.
This patch allows Linux find a rootfs partition after installing custom
image with a CFE bootloader.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
devm_kzalloc is device managed and simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some bright specification writers decided to write this in the ONFI spec
(from ONFI 3.0, Section 3.1):
"The number of blocks and number of pages per block is not required to
be a power of two. In the case where one of these values is not a
power of two, the corresponding address shall be rounded to an
integral number of bits such that it addresses a range up to the
subsequent power of two value. The host shall not access upper
addresses in a range that is shown as not supported."
This breaks every assumption MTD makes about NAND block/chip-size
dimensions -- they *must* be a power of two!
And of course, an enterprising manufacturer has made use of this lovely
freedom. Exhibit A: Micron MT29F32G08CBADAWP
"- Plane size: 2 planes x 1064 blocks per plane
- Device size: 32Gb: 2128 blockss [sic]"
This quickly hits a BUG() in nand_base.c, since the extra dimensions
overflow so we think it's a second chip (on my single-chip setup):
ONFI param page 0 valid
ONFI flash detected
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x44 (Micron MT29F32G08CBADAWP), 4256MiB, page size: 8192, OOB size: 744
------------[ cut here ]------------
kernel BUG at drivers/mtd/nand/nand_base.c:203!
Internal error: Oops - BUG: 0 [#1] SMP ARM
[... trim ...]
[<c02cf3e4>] (nand_select_chip+0x18/0x2c) from [<c02d25c0>] (nand_do_read_ops+0x90/0x424)
[<c02d25c0>] (nand_do_read_ops+0x90/0x424) from [<c02d2dd8>] (nand_read+0x54/0x78)
[<c02d2dd8>] (nand_read+0x54/0x78) from [<c02ad2c8>] (mtd_read+0x84/0xbc)
[<c02ad2c8>] (mtd_read+0x84/0xbc) from [<c02d4b28>] (scan_read.clone.4+0x4c/0x64)
[<c02d4b28>] (scan_read.clone.4+0x4c/0x64) from [<c02d4c88>] (search_bbt+0x148/0x290)
[<c02d4c88>] (search_bbt+0x148/0x290) from [<c02d4ea4>] (nand_scan_bbt+0xd4/0x5c0)
[... trim ...]
---[ end trace 0c9363860d865ff2 ]---
So to fix this, just truncate these dimensions down to the greatest
power-of-2 dimension that is less than or equal to the specified
dimension.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: <stable@vger.kernel.org>
This commit replaces the currently hardcoded buffer size, by a
dynamic detection scheme. First a small 256 bytes buffer is allocated
so the device can be detected (using READID and friends commands).
After detection, this buffer is released and a new buffer is allocated
to acommodate the page size plus out-of-band size.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Instead of setting info->dma each time a command is prepared,
we can move it after the DMA buffers are allocated.
This is more clear and it's the proper place to enable this, given
DMA cannot be turned on and off during runtime.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Micron N25Q512A is a spi flash memory with following features:
-64MB size, 1.8V, Mulitple I/O, 4KB Sector erase memory.
-Memory is organised as 1024(64KB) main sectors.
-Each sector is divided into 256 pages.
-Register set/Opcodes are similar to other N25Q family products.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use free_bch() instead of kfree() to free init_bch()
allocated data.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The loop that polls the status register waiting for an operation to complete
foolishly bases the timeout simply on the number of loop iterations that have
ocurred. When I increased the processor clock speed, timeouts started to appear
for long block erasure operations. This patch measures the timeout using
jiffies.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
devm_kzalloc is device managed and makes code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Driver core will set the driver data to NULL upon detach or
probe failure.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
module_platform_driver removes boiler plate code and makes it
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Huang Shijie
Rodolfo Giometti
Geert Uytterhoeven
Uwe Kleine-König
Brian Norris
Ezequiel Garcia
Gerhard Sittig
Huang Shijie
Prabhakar Kushwaha
Cai Zhiyong
Sachin Kamat
Josh Triplett
Qi Wang 王起 (qiwang)
Rafał Miłecki
Jingoo Han
Linus Torvalds
Rob Herring
Rashika Kheria
Ivan Khoronzhuk
Wei Yongjun
Laurent Pinchart
Axel Lin
Fabio Estevam
Igor Grinberg
Michael Grzeschik
Alexander Shiyan
Geert Uytterhoeven
Sourav Poddar
Julia Lawall
Vinod Koul
Wolfram Sang
Bartlomiej Zolnierkiewicz
Vladimir Zapolskiy
Josh Wu
Michael Opdenacker
Mark Brown
Pekon Gupta
Hauke Mehrtens
Priyanka Jain
Mike Dunn