This patch adds nanoEngine PCMCIA support, with support for two sockets.
In order to have a fully functional pcmcia subsystem in a BSE
nanoEngine board you should carefully read this:
http://cambuca.ldhs.cetuc.puc-rio.br/nanoengine/
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes checkpatch.pl issues in drivers/pcmcia/soc_common.c.
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The new FPGA firmware in Balloon3 uses different methods to control it's bus
control lines. In the new version, there are separate registers to set/clear
bus control lines. This patch updates affected places.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This driver also contains structures to eventually support PXA320. This is
planned to be added in a later patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
On PXA320, there's only one PCMCIA slot available. Check for cases where the
user would want to register multiple. Also, rework failpath.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is important because on PXA3xx, the physical mapping of SMEMC registers
differs from the one on PXA2xx. In order to get PCMCIA working on both PXA2xx
and PXA320, the PCMCIA driver was adjusted accordingly as well.
Also, various places in the kernel had to be patched to use
__raw_read/__raw_write.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
ARM: pcmcia: Fix for building DEBUG with sa11xx_base.c as a module.
This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
Cc: <stable@kernel.org>
Signed-off-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.
Signed-off-by: Joe Perches <joe@perches.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Eric Miao <eric.y.miao@gmail.com>
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
These are called by sa11x0_drv_pcmcia_probe (which is marked now with
__devinit) so they can go to .devinit.text now, too.
This fixes:
WARNING: drivers/pcmcia/sa1100_cs.o(.text+0x10): Section mismatch in reference from the function sa11x0_drv_pcmcia_probe() to the function .init.text:pcmcia_simpad_init()
The function sa11x0_drv_pcmcia_probe() references
the function __init pcmcia_simpad_init().
This is often because sa11x0_drv_pcmcia_probe lacks a __init
annotation or the annotation of pcmcia_simpad_init is wrong.
and a similar warning for pcmcia_collie_init, pcmcia_cerf_init,
pcmcia_h3600_init and pcmcia_shannon_init.
While at it mark pcmcia_assabet_init with __devinit, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
CC: Russell King <linux@arm.linux.org.uk>
CC: Eric Miao <eric.y.miao@gmail.com>
CC: linux-arm-kernel@lists.infradead.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Dave Hinds pointed out to me that 37979e1546 will break b43 and
ray_cs, as IOCARD is not -- as the name would suggest -- only needed
for cards using IO ports. Instead, as it re-deines several pins, it
is also required for using interrupts.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
au100_generic and soc_common call flush_scheduled_work() spuriously.
Remove them.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Some cards need the speedups on, some need them off. As we can't detect
this reliably, at least give the users a hint how to tweak the system.
Reported-by: David Bluecame <david.bluecame@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_socket_dev_resume() is only referenced from macro
SET_SYSTEM_SLEEP_PM_OPS(NULL, pcmcia_socket_dev_resume)
which based on CONFIG_PM_SLEEP may or may not actually
use its second parameter.
Signed-off-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
- pci_release_regions called during return error path.
- pci_disable_device called for cases where earlier it was enabled.
- code duplication avoided/reduced by adding resource release at goto statements.
Signed-off-by: Rahul Ruikar <rahul.ruikar@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Fill in missing descriptions and update some others for functions in
pcmcia_resource.c.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The Status (CISREG_CCSR) and ExtStatus (CISREG_ESR) registers were
only accessed to enable audio output for some drivers and IRQ for
serial_cs.c. The former also required setting config_req_t.Attributes
to CONF_ENABLE_SPKR; the latter can be simplified to setting this
field to CONF_ENABLE_ESR.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: linux-scsi@vger.kernel.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The "Pin" and "Copy" configuration registers (CISREG_SCR, CISREG_PPR)
do not seem to be utilized anywhere. If a device would request a
write to these registers, "0" would be written. Continue to do so, but
warn of unexpected behavior -- and remove the "Pin" and "Copy" entries
from config_req_t.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_modify_configuration() was only used by two drivers to fix up
one issue each: setting the Vpp to a different value, and reducing
the IO width to 8 bit. Introduce two explicitly named functions
handling these things, and remove one further typedef.
CC: netdev@vger.kernel.org
CC: linux-mtd@lists.infradead.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of win_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[2,3,4,5] for up to four iomem
ranges. After a call to pcmcia_request_window(), the windows found there
are reserved and may be used until pcmcia_release_window() is called.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-mtd@lists.infradead.org
CC: Jiri Kosina <jkosina@suse.cz>
CC: linux-scsi@vger.kernel.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
If pcmcia_request_io() only fails partly -- for the second of two
requested resources -- preserve the configuration settings for the
first one.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As the iomem / ioport setup differs per device, it is much better
to print out the device instead of the socket.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid buffer overflow in pcmcia_setup_isa_irq
pcmcia: do not request windows if you don't need to
pcmcia: insert PCMCIA device resources into resource tree
pcmcia: export resource information to sysfs
pcmcia: use struct resource for PCMCIA devices, part 2
pcmcia: remove memreq_t
pcmcia: move local definitions out of include/pcmcia/cs.h
pcmcia: do not use io_req_t when calling pcmcia_request_io()
pcmcia: do not use io_req_t after call to pcmcia_request_io()
pcmcia: use struct resource for PCMCIA devices
pcmcia: clean up cs.h
pcmcia: use pcmica_{read,write}_config_byte
pcmcia: remove cs_types.h
pcmcia: remove unused flag, simplify headers
pcmcia: remove obsolete CS_EVENT_ definitions
pcmcia: split up central event handler
pcmcia: simplify event callback
pcmcia: remove obsolete ioctl
Conflicts in:
- drivers/staging/comedi/drivers/*
- drivers/staging/wlags49_h2/wl_cs.c
due to dev_info_t and whitespace changes
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (150 commits)
MIPS: PowerTV: Separate PowerTV USB support from non-USB code
MIPS: strip the un-needed sections of vmlinuz
MIPS: Clean up the calculation of VMLINUZ_LOAD_ADDRESS
MIPS: Clean up arch/mips/boot/compressed/decompress.c
MIPS: Clean up arch/mips/boot/compressed/ld.script
MIPS: Unify the suffix of compressed vmlinux.bin
MIPS: PowerTV: Add Gaia platform definitions.
MIPS: BCM47xx: Fix nvram_getenv return value.
MIPS: Octeon: Allow more than 3.75GB of memory with PCIe
MIPS: Clean up notify_die() usage.
MIPS: Remove unused task_struct.trap_no field.
Documentation: Mention that KProbes is supported on MIPS
SAMPLES: kprobe_example: Make it print something on MIPS.
MIPS: kprobe: Add support.
MIPS: Add instrunction format for BREAK and SYSCALL
MIPS: kprobes: Define regs_return_value()
MIPS: Ritually kill stupid printk.
MIPS: Octeon: Disallow MSI-X interrupt and fall back to MSI interrupts.
MIPS: Octeon: Support 256 MSI on PCIe
MIPS: Decode core number for R2 CPUs.
...
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
NR_IRQS may be as low as 16, causing a (harmless?) buffer overflow in
pcmcia_setup_isa_irq():
static u8 pcmcia_used_irq[NR_IRQS];
...
if ((try < 32) && pcmcia_used_irq[irq])
continue;
This is read-only, so if this address would be non-zero, it would just
mean we would not attempt an IRQ >= NR_IRQS -- which would fail anyway!
And as request_irq() fails for an irq >= NR_IRQS, the setting code path:
pcmcia_used_irq[irq]++;
is never reached as well.
Reported-by: Christoph Fritz <chf.fritz@googlemail.com>
CC: stable@kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Insert PCMCIA device resources into the resource tree. However, this is
currently only implemented for sockets which do not statically map the
resources.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Russell King
Marcelo Roberto Jimenez
Marek Vasut
Eric Miao
Joe Perches
Uwe Kleine-König
Komuro
Linus Torvalds
Dominik Brodowski
Justin P. Mattock
Tejun Heo
Wolfram Sang
Maciej Żenczykowski
Rahul Ruikar
Grant Likely
Manuel Lauss
Jiri Kosina