Prevents direct charging control in cable notification and only set the
input current limit according to cable type. Leave the enabling of
charing to cm_monitor() where charging management proceeds. We may lose
a few ms to enable charging compared to before, but it's more important
that charging is enabled always in safe context.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
cm_monitor(), where charging management starts, checks various charging
condition sequentially to decide next charging operation. However, as it
follows sequential process, cascaded if statements, it does some
jobs which have already done in the previous stage. This results in a
delay in decision making. Moreover, starting point of charging is spread
all around which makes maintain code and debugging difficult.
Both of the problems mentioned above become clean if it manages battery
charging focusing on battery status not following sequential condition
checking. Now, cm_monitor() moves battery state diagram and does the
optimal operation for current state. As a result, it reduces whole
monitoring time almost in half.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Current charger-manager calls power_supply_changed() whenever charging
status is changed. Remove the separated power_supply_changed() calls
and let it be called at end of try_charger_enable() function which
is called to set charging/discharging.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The POWER_SUPPLY_CHARGE_NOW/FULL property reflects battery's charges
in uAh unit, but charger-manager has been used it wrongly as a
status field.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We were using POWER_SUPPLY_PROP_TEMP if the temperature was coming
via the fuel gauge and POWER_SUPPLY_PROP_TEMP_AMBIENT if it was
coming via the thermal framework. Since they're mutually
exclusive in the driver and we don't know if the thermal framework
is ambient or not, unify them both to use POWER_SUPPLY_PROP_TEMP.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
cm_notify_event() was introduced to get an event associated with the
battery status externally (ie in board files), but no one ever used it.
Moreover it makes charger manager driver more complicated. Drop the
function and all data related to it to simplify the driver.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Whenever the battery status is changed, charger manager triggers a uevent
through a private interface. Modify it to use power_supply_changed()
since it belongs to the power supply subsystem.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Both chips have charger and a fuel gauge.
This adds basic support for displaying the state of the battery and the
input power, settings are not modified. There are some defaults set via
OTP.
Charging also starts after plugging USB.
Known issues of the fuel gauge: There are drivers in the wild which disable
the fuel gauge at shutdown. If a kernel is booted without fuel gauge
support, after such a driver has been used, the fuel gauge will stay off
and decalibrate.
If this driver is used after that, it might display wrong values for charge
level.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Current sbs-battery considers all smbus errors as disconnection events
when battery-detect pin isn't supplied, and restored to present state back
when any successful transaction is made.
This can lead to unwanted state changes between present and !present
when there's one i2c error and other following commands were successful.
This patch provides a unified way of checking presence by calling
sbs_get_battery_presence_and_health() when detect pin is not used.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Simplify the driver and remove the DT specific code by
using the generic device property framework.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are no platforms using the pdata support, so let's
drop it to simplify the driver.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Update the license to the SPDX licensing format.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is a spelling mistake in a dev_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch enables calling sbs_get_battery_presence_and_health()
without checking its chip type. No functional changes.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove unused enable_detection flag which is always true after
the device is proved.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add new charge-current-limit feature to gpio-charger.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This immutable branch drops legacy gpio API from
gpio-charger and updates the remaining users to
the new gpiod API instead.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----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=RhVS
-----END PGP SIGNATURE-----
Merge tag 'psy-arm-gpio-charger-immutable-for-5.10-signed' into psy-next
Immutable branch between arm and power-supply for gpio-charger for 5.10
This immutable branch drops legacy gpio API from
gpio-charger and updates the remaining users to
the new gpiod API instead.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This converts the GPIO charger to use exclusively GPIO
descriptors, moving the two remaining platforms passing
global GPIO numbers over to using a GPIO descriptor table.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently, power_supply framework supports only Battery, UPS,
Mains and USB power_supply_type. Add wireless power_supply_type
so that the drivers which supports wireless can register a power
supply class device with POWER_SUPPLY_TYPE_WIRELESS.
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Let's simply disable/enable IRQ rather than use a mutex that protects from
racing with the interrupt handler. The result of this patch is that it's a
bit easier now to follow the driver's code.
Tested-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SMB347 is a charger and not a battery driver. Secondly, power-supply core
now supports monitored-battery. So the 'fake' battery doesn't do anything
useful for us, and thus, it should be removed.
Transfer smb347-battery functionality into smb347-mains and smb347-usb.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds device-tree support to the SMB347 charger driver. All
legacy platform data now can be parsed from DT. Because of that and since
SMB347 is an I2C client driver, the IRQ number can be passed automatically
through client's IRQ variable if it's defined in DT. There is no need to
map GPIO to IRQ manually in the case of DT.
This patch is based on the original work made by:
Jonghwa Lee <jonghwa3.lee@samsung.com>
Link: https://patchwork.kernel.org/patch/4284731/
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The generic battery temperature properties are already supported by the
power-supply core. Let's support parsing of the common battery temperature
properties from a device-tree.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Simplify code, more convenient to use with Device Tree.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Constify a number of static variables that are not modified to allow the
compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This battery appears only to be used by a single board (DA850), so it
makes sense to add this to the Kconfig file so that users don't build
the module unnecessarily. It currently seems to be built for the x86
Arch Linux kernel where it's probably not doing much good.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Acked-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are multiple drivers using the private adc interface.
It seems unlikely that they would ever get converted to iio,
so make the current state official by making the header file
global.
The s3c2410_ts driver needs a couple of register definitions
as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-22-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This is a long life mode set in the factory for extended warranty
battery, the power charging rate is customized so that battery at
work last longer.
Presently switching to a different battery charging mode is through
EC PID 0x0710 to configure the battery firmware, this operation will
be blocked by EC with failure code 0x01 when PLL mode is already
in use.
Signed-off-by: Crag Wang <crag.wang@dell.com>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add the Texas Instruments BQ28z610 battery monitor.
The register address map is laid out the same as compared to other
devices within the file.
The battery status register bits are similar to the bq27z561 but they
are different compared to other fuel gauge devices within this file.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add the Texas Instruments BQ27Z561 battery monitor. The register address
map is laid out the same as compared to other devices within the file.
The battery status register has differing bits to determine if the
battery is full, discharging or dead.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since default battery_status is POWER_SUPPLY_STATUS_DISCHARGING,
we should change default battery_current to a negative value.
Signed-off-by: LH Lin <lh.lin@mediatek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix W=1 compile warnings (invalid kerneldoc):
drivers/power/supply/power_supply_core.c:747: warning: Function parameter or member 'temp' not described in 'power_supply_temp2resist_simple'
drivers/power/supply/power_supply_core.c:747: warning: Excess function parameter 'ocv' description in 'power_supply_temp2resist_simple'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix W=1 compile warnings (invalid kerneldoc):
drivers/power/supply/cpcap-battery.c:292: warning: Function parameter or member 'ccd' not described in 'cpcap_battery_read_accumulated'
drivers/power/supply/cpcap-battery.c:292: warning: Excess function parameter 'regs' description in 'cpcap_battery_read_accumulated'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the function rt5033_battery_probe(), it should return -ENOMEM
instead of -EINVAL when call function devm_kzalloc() failed.
Signed-off-by: Peng Fan <fanpeng@loongson.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adds the property POWER_SUPPLY_PROP_CAPACITY_ALERT_MIN to export the
chip->low_soc_alert and add the property as writeable, implementing
max17040_prop_writeable and max17040_set_property, so with that the
user space can readjust the alerts.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
clang static analysis flags this error
88pm860x_battery.c:522:19: warning: Assigned value is
garbage or undefined [core.uninitialized.Assign]
info->start_soc = soc;
^ ~~~
soc is set by calling calc_soc.
But calc_soc can return without setting soc.
So check the return status and bail similarly to other
checks in pm860x_init_battery and initialize soc to
silence the warning.
Fixes: a830d28b48 ("power_supply: Enable battery-charger for 88pm860x")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
[also update recently added ti.com http links]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some Buffalo LinkStations perform the power off operation, at restart
time, depending on the state of an output pin (LED2/INTn) at the ethernet
PHY. This pin is also used to wake the machine when a WoL packet is
received by the PHY.
The driver is required by the Buffalo LinkStation LS421DE (ARM MVEBU),
and other models. Without it, the board remains forever halted if a
power off command is executed, unless the PSU is disconnected and
connected again.
Add the driver to provide the power off function and also make the WoL
feature to be available.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The input parameter is int type, cause adc * 1000 could overflow.
Change to use s64 to avoid this issue.
Signed-off-by: Chen Yongzhi <yongzhi.chen@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yongqiang Liu <liuyongqiang13@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce the bq2515x family of chargers.
The BQ2515X family of devices are highly integrated battery management
ICs that integrate the most common functions for wearable devices
namely a charger, an output voltage rail, ADC for battery and system
monitoring, and a push-button controller.
Datasheets:
bq25150 - http://www.ti.com/lit/ds/symlink/bq25150.pdf
bq25155 - http://www.ti.com/lit/ds/symlink/bq25155.pdf
Signed-off-by: Ricardo Rivera-Matos <r-rivera-matos@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add HEALTH_WARM, HEALTH_COOL and HEALTH_HOT to the health enum.
HEALTH_WARM, HEALTH_COOL, and HEALTH_HOT properties are taken
from JEITA specification JISC8712:2015
Acked-by: Andrew F. Davis <afd@ti.com>
Tested-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
The ONLINE prop should be when the charger is present (ie able to
charge), however, it was for when it was actually charging or not.
Instead, add the STATUS prop to show whether charging is actually
going on or not.
The magic numbers have been ported from a downstream kernel for the
SGH-T959V.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SBS batteries optionally have support for PEC. This enables
PEC handling based on the implemented SBS version as suggested
by the standard. The support for PEC is re-evaluated when the
battery is hotplugged into the system, since there might be
systems supporting batteries from different SBS generations.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The SBS battery implements SMBus block reads. Currently the
driver "emulates" this by doing an I2C byte read for the
length followed by an I2C block read. The I2C subsystem
actually provides a proper API for doing SMBus block reads,
which can and should be used instead. The current implementation
does not properly handle packet error checking (PEC).
Not all upstream systems using sbs-battery have I2C bus drivers
supporting I2C_M_RECV_LEN, so old implementation is kept as
fallback to keep things working. But this prints a warning,
which hopefully results in people implementing support for it.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
While strongly recommended, not all devices have a gpio to
detect if the charger is connected. This moves the 'gpios'
from required to optional section.
This also modifies error handling for the GPIO a bit: We
no longer fallback to pdata, if a GPIO is specified using
GPIO descriptor tables. This is a bit cleaner and does
not have any real impact: There are only two mainline pdata
users (arm/mach-sa1100/collie.c, arm/mach-pxa/tosa.c) and
none of them specify the GPIO via gpiod descriptor tables.
Once both have been converted the driver's support for
specifying GPIOs numbers in pdata will be dropped.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use kobj_to_dev() API instead of open-coded container_of().
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
kobject:
* Increase number of allowed uevent variables
power-supply core:
* Add power-supply type in uevent
* Cleanup property handling in core
* Make property and usb_type pointers const
* Convert core power-supply DT binding to YAML
* Cleanup HWMON code
* Add new health status "calibration required"
* Add new properties for manufacture date and
capacity error margin
battery drivers:
* new cw2015 battery driver used by pine64 Pinebook Pro laptop
* axp22: blacklist on Meegopad T02
* sc27xx: support current/voltage reading
* max17042: support time-to-empty reading
* simple-battery: add more battery parameters
* bq27xxx: convert DT binding document to YAML
* sbs-battery: add TI BQ20Z65 support, fix technology property, convert
DT binding to YAML, add option to disable charger
broadcasts, add new properties: manufacture date,
capacity error margin, average current, charge current
and voltage and support calibration required health
status
* misc. fixes
charger drivers:
* bq25890: cleanup, implement charge type, precharge current and input
current limiting properties
* bd70528: use new linear range helper library
* bd99954: new charger driver
* mp2629: new charger driver
* misc. fixes
reboot drivers:
* oxnas-restart: introduce new driver
* syscon-reboot: convert DT binding to YAML, add parent syscon device support
* misc. fixes
-----BEGIN PGP SIGNATURE-----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=He9L
-----END PGP SIGNATURE-----
Merge tag 'for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"This time there are lots of changes. Quite a few changes to the core,
lots of driver changes and one change to kobject core (with Ack from
Greg).
Summary:
kobject:
- Increase number of allowed uevent variables
power-supply core:
- Add power-supply type in uevent
- Cleanup property handling in core
- Make property and usb_type pointers const
- Convert core power-supply DT binding to YAML
- Cleanup HWMON code
- Add new health status "calibration required"
- Add new properties for manufacture date and capacity error margin
battery drivers:
- new cw2015 battery driver used by pine64 Pinebook Pro laptop
- axp22: blacklist on Meegopad T02
- sc27xx: support current/voltage reading
- max17042: support time-to-empty reading
- simple-battery: add more battery parameters
- bq27xxx: convert DT binding document to YAML
- sbs-battery: add TI BQ20Z65 support, fix technology property,
convert DT binding to YAML, add option to disable charger
broadcasts, add new properties: manufacture date, capacity
error margin, average current, charge current and voltage and
support calibration required health status
- misc fixes
charger drivers:
- bq25890: cleanup, implement charge type, precharge current and
input current limiting properties
- bd70528: use new linear range helper library
- bd99954: new charger driver
- mp2629: new charger driver
- misc fixes
reboot drivers:
- oxnas-restart: introduce new driver
- syscon-reboot: convert DT binding to YAML, add parent syscon device
support
- misc fixes"
* tag 'for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (85 commits)
power: supply: cw2015: Attach OF ID table to the driver
power: reset: gpio-poweroff: add missing '\n' in dev_err()
Revert "power: supply: sbs-battery: simplify read_read_string_data"
Revert "power: supply: sbs-battery: add PEC support"
dt-bindings: power: sbs-battery: Convert to yaml
power: supply: sbs-battery: constify power-supply property array
power: supply: sbs-battery: switch to i2c's probe_new
power: supply: sbs-battery: switch from of_property_* to device_property_*
power: supply: sbs-battery: add ability to disable charger broadcasts
power: supply: sbs-battery: fix idle battery status
power: supply: sbs-battery: add POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED support
power: supply: sbs-battery: add MANUFACTURE_DATE support
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT/VOLTAGE_MAX support
power: supply: sbs-battery: Improve POWER_SUPPLY_PROP_TECHNOLOGY support
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CURRENT_AVG support
power: supply: sbs-battery: add PEC support
power: supply: sbs-battery: simplify read_read_string_data
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CAPACITY_ERROR_MARGIN support
power: supply: sbs-battery: Add TI BQ20Z65 support
power: supply: core: add POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED
...
It appears that OF ID table was hanging around without being attached
to the driver. Attach it properly.
Fixes: b4c7715c10 ("power: supply: add CellWise cw2015 fuel gauge driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-By: Tobias Schramm <t.schramm@manjaro.org>
Tested-By: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
- Constify 'properties' attribute in core header file
- New Drivers
- Add support for Gateworks System Controller
- Add support for MediaTek MT6358 PMIC
- Add support for Mediatek MT6360 PMIC
- Add support for Monolithic Power Systems MP2629 ADC and Battery charger
- Rework Intel's SCU IPC collection
- Eliminate near duplicate IPC functionality
- Split out MFD related activities into a dedicated MFD driver
- Fix-ups
- Use new I2C API; htc-i2cpld
- Remove superfluous code; sprd-sc27xx-spi
- Improve error handling; stm32-timers
- Device Tree additions/fixes; mt6397
- Defer probe betterment; wm8994-core
- Improve module handling; wm8994-core
- Staticify; stpmic1
- Trivial (spelling, formatting); tqmx86
- Bug Fixes
- Fix incorrect register/PCI IDs; intel-lpss-pci
- Fix unbalanced Regulator API calls; wm8994-core
- Fix double free(); wcd934x
- Remove IRQ domain on failure; stmfx
- Reset chip on resume; stmfx
- Disable/enable IRQs on suspend/resume; stmfx
- Do not use bulk writes on H/W which does not support them; max77620
-----BEGIN PGP SIGNATURE-----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=746a
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Constify 'properties' attribute in core header file
New Drivers:
- Add support for Gateworks System Controller
- Add support for MediaTek MT6358 PMIC
- Add support for Mediatek MT6360 PMIC
- Add support for Monolithic Power Systems MP2629 ADC and Battery charger
Fix-ups:
- Use new I2C API in htc-i2cpld
- Remove superfluous code in sprd-sc27xx-spi
- Improve error handling in stm32-timers
- Device Tree additions/fixes in mt6397
- Defer probe betterment in wm8994-core
- Improve module handling in wm8994-core
- Staticify in stpmic1
- Trivial (spelling, formatting) in tqmx86
Bug Fixes:
- Fix incorrect register/PCI IDs in intel-lpss-pci
- Fix unbalanced Regulator API calls in wm8994-core
- Fix double free() in wcd934x
- Remove IRQ domain on failure in stmfx
- Reset chip on resume in stmfx
- Disable/enable IRQs on suspend/resume in stmfx
- Do not use bulk writes on H/W which does not support them in max77620"
* tag 'mfd-next-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (29 commits)
mfd: mt6360: Remove duplicate REGMAP_IRQ_REG_LINE() entry
mfd: Add support for PMIC MT6360
mfd: max77620: Use single-byte writes on MAX77620
mfd: wcd934x: Drop kfree for memory allocated with devm_kzalloc
mfd: stmfx: Disable IRQ in suspend to avoid spurious interrupt
mfd: stmfx: Fix stmfx_irq_init error path
mfd: stmfx: Reset chip on resume as supply was disabled
mfd: wm8994: Silence warning about supplies during deferred probe
mfd: wm8994: Fix unbalanced calls to regulator_bulk_disable()
mfd: wm8994: Fix driver operation if loaded as modules
dt-bindings: mfd: mediatek: Add MT6397 Pin Controller
mfd: Constify properties in mfd_cell
mfd: stm32-timers: Use dma_request_chan() instead dma_request_slave_channel()
mfd: sprd: Remove unnecessary spi_bus_type setting
mfd: intel-lpss: Update LPSS UART #2 PCI ID for Jasper Lake
mfd: tqmx86: Fix a typo in MODULE_DESCRIPTION
mfd: stpmic1: Make stpmic1_regmap_config static
mfd: htc-i2cpld: Convert to use i2c_new_client_device()
MAINTAINERS: Add entry for mp2629 Battery Charger driver
power: supply: mp2629: Add impedance compensation config
...
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
The commit is a nice cleanup, but breaks booting on exynos5 based
chromebooks. It's seems to come down to exynos5's i2c driver not
implementing I2C_FUNC_SMBUS_READ_BLOCK_DATA. It's not yet clear
why that breaks boot / massively slows it down when userspace
starts, so revert the problematic patch.
This reverts commit c4b12a2f3f.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This depends on the simplification of sbs_read_string_data, which
breaks booting exynos5 based chromebooks. More investigation is
required, so this patch and the simplification patch are reverted
for this merge window.
Note, that this is only a partial revert, since sbs_update_presence()
has not been removed. It is also required for the charger broadcast
disabling.
This reverts commit 79bcd5a4a6.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Switch from DT specific of_property_* API to generic and more
modern device_property_* API.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In certain designs, it is possible to add a battery on a populated i2c
bus without an sbs compliant charger. In that case, the battery will
unnecessarily and sometimes undesirably master the bus trying to write
info in the charger.
It is observed in many occasion that these battery "broadcasts" are even
corrupting other ongoing master to slave communication. I.e. the
multi-master support in the battery is inadequate.
Thankfully, the CHARGER_MODE bit allows designers to disable that SBS
battery behaviour.
This needs to be done once when the battery is first seen on the bus.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
[rebased code]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
A battery, that is neither charged, nor discharged is not
always Full. If the charger is disabled for other reasons
it might simply be idle and should be marked accordingly.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for reporting the SBS battery's condition flag
to userspace using the new "Calibration required" health status.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Expose the battery's manufacture date to userspace.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Expose maximum charge current/voltage information requested
by the battery.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This reads the battery chemistry from the battery chip instead
of incorrectly hardcoding the type to be Li-Ion.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Expose averaged current information, which is part of the SBS
standard and should be supported by all batteries.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SBS batteries optionally have support for PEC. This enables
PEC handling based on the implemented SBS version as suggested
by the standard. The support for PEC is re-evaluated when the
battery is hotplugged into the system, since there might be
systems supporting batteries from different SBS generations.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The SBS battery implements SMBus block reads. Currently the
driver "emulates" this by doing an I2C byte read for the
length followed by an I2C block read. The I2C subsystem
actually provides a proper API for doing SMBus block reads,
which can and should be used instead. The current implementation
does not properly handle packet error checking (PEC).
This change requires, that I2C bus drivers support I2C_M_RECV_LEN
or directly provide the SMBus API to access device manufacturer
and model name.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for reporting the MaxError register from
battery fuel gauges following the smart battery standard.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for BQ20Z65 manufacturer data to the sbs-battery
driver. Implementation has been verified using the public TRM
available from [0] and tested using a GE Flex 3S2P battery.
[0] http://www.ti.com/lit/pdf/sluu386
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some battery fuel gauges know when the battery needs to
be recalibrated before providing usable values. This
should be reported via the health property.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some smart batteries store their manufacture date, which is
useful to identify the battery and/or to know about the cell
quality.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following sparse warning:
drivers/power/supply/bd99954-charger.c:1028:6: warning: symbol 'bd9995x_chip_reset' was not declared.
The bd9995x_chip_reset() has only one call site within bd99954-charger.c
It should be static
Fixes: 0902f83664 ("power: supply: Support ROHM bd99954 charger")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
An allmodconfig kernel makes CONFIG_VEXPRESS_CONFIG a module and
CONFIG_POWER_RESET_VEXPRESS builtin. That makes us see this build
error:
aarch64-linux-gnu-ld: drivers/power/reset/vexpress-poweroff.o: in function `vexpress_reset_probe':
../drivers/power/reset/vexpress-poweroff.c:119: undefined reference to `devm_regmap_init_vexpress_config'
../drivers/power/reset/vexpress-poweroff.c:119:(.text+0x48c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol
`devm_regmap_init_vexpress_config'
make[1]: *** [/srv/src/kernel/next/Makefile:1126: vmlinux] Error 1
Rework so that POWER_RESET_VEXPRESS depends on 'VEXPRESS_CONFIG=y'.
Link: https://lore.kernel.org/r/20200527112608.3886105-5-anders.roxell@linaro.org
Fixes: d06cfe3f12 ("bus: vexpress-config: Merge vexpress-syscfg into vexpress-config")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the helper macro for builtin drivers taht don't do anything special
in driver init. This removes some boilerplate code.
Link: https://lore.kernel.org/r/20200527112608.3886105-3-anders.roxell@linaro.org
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Make sure that the POWER_RESET_VEXPRESS driver won't have bind/unbind
attributes available via the sysfs, so lets be explicit here and use
".suppress_bind_attrs = true" to prevent userspace from doing something
silly.
Link: https://lore.kernel.org/r/20200527112608.3886105-2-anders.roxell@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add device tree compatible strings and create proper modalias structures
to let this driver load automatically if compiled as module, because
max14577 MFD driver creates MFD cells with such compatible strings.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=89mP
-----END PGP SIGNATURE-----
Merge tag 'tags/ib-mfd-iio-power-v5.8' into psy-next
This merges the MP2629 battery charge management immutable branch
between MFD, IIO and power-supply due for the v5.8 merge window
into power-supply for-next branch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since normally syscon-reboot block is supposed to be a part of a system
controller, lets look for the syscon regmap in a parental DT node if
regmap property isn't specified. DT binding from now considers the regmap
property as deprecated.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The mp2629 provides switching-mode battery charge management for
single-cell Li-ion or Li-polymer battery. Driver supports the
access/control input source and battery charging parameters.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This add support for the MediaTek MT6358 RTC. Driver using
compatible data to store different RTC_WRTGR address offset.
This replace RTC_WRTGR to RTC_WRTGR_MT6323 in mt6323-poweroff
driver which only needed by armv7 CPU without ATF.
Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move away from the deprecated API in this comment.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Report REG00.IINLIM value as INPUT_CURRENT_LIMIT property.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Report charging type based on recently read state.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Edge interrupts from the charger may be lost or stuck in fault mode
since probe(). Check if something changed everytime userspace wants
some data.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Datasheet describes two modes for reading ADC measurements:
1. continuous, 1 Hz - enabled and started by CONV_RATE bit
2. one-shot - triggered by CONV_START bit
In continuous mode, CONV_START is read-only and signifies an ongoing
conversion.
Change the code to follow the datasheet and really disable continuous
mode for power saving.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Jonghwa Lee
Jonathan Bakker
Andreas Kemnade
Ikjoon Jang
Sebastian Reichel
Dan Murphy
Colin Ian King
Sebastian Reichel
Linus Walleij
Krzysztof Kozlowski
Subbaraman Narayanamurthy
Dmitry Osipenko
David Heidelberg
Rikard Falkeborn
Alex Dewar
Gustavo A. R. Silva
Arnd Bergmann
Linus Torvalds
Crag Wang
LH Lin
Peng Fan
Matheus Castello
Tom Rix
Alexander A. Klimov
Daniel González Cabanelas
Chunyan Zhang
Yongqiang Liu
Ricardo Rivera-Matos
Andrzej Pietrasiewicz
Dinghao Liu
Keyur Patel
Wang Qing
Andy Shevchenko
Luca Ceresoli
Jean-Francois Dagenais
Samuel Zou
Anders Roxell
Marek Szyprowski
Serge Semin
Lee Jones
Saravanan Sekar
Ran Bi
Wolfram Sang
Michał Mirosław