Add HEALTH_WARM, HEALTH_COOL and HEALTH_HOT to the health enum.
HEALTH_WARM, HEALTH_COOL, and HEALTH_HOT properties are taken
from JEITA specification JISC8712:2015
Acked-by: Andrew F. Davis <afd@ti.com>
Tested-by: Guru Das Srinagesh <gurus@codeaurora.org>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
The ONLINE prop should be when the charger is present (ie able to
charge), however, it was for when it was actually charging or not.
Instead, add the STATUS prop to show whether charging is actually
going on or not.
The magic numbers have been ported from a downstream kernel for the
SGH-T959V.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SBS batteries optionally have support for PEC. This enables
PEC handling based on the implemented SBS version as suggested
by the standard. The support for PEC is re-evaluated when the
battery is hotplugged into the system, since there might be
systems supporting batteries from different SBS generations.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The SBS battery implements SMBus block reads. Currently the
driver "emulates" this by doing an I2C byte read for the
length followed by an I2C block read. The I2C subsystem
actually provides a proper API for doing SMBus block reads,
which can and should be used instead. The current implementation
does not properly handle packet error checking (PEC).
Not all upstream systems using sbs-battery have I2C bus drivers
supporting I2C_M_RECV_LEN, so old implementation is kept as
fallback to keep things working. But this prints a warning,
which hopefully results in people implementing support for it.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
While strongly recommended, not all devices have a gpio to
detect if the charger is connected. This moves the 'gpios'
from required to optional section.
This also modifies error handling for the GPIO a bit: We
no longer fallback to pdata, if a GPIO is specified using
GPIO descriptor tables. This is a bit cleaner and does
not have any real impact: There are only two mainline pdata
users (arm/mach-sa1100/collie.c, arm/mach-pxa/tosa.c) and
none of them specify the GPIO via gpiod descriptor tables.
Once both have been converted the driver's support for
specifying GPIOs numbers in pdata will be dropped.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use kobj_to_dev() API instead of open-coded container_of().
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
kobject:
* Increase number of allowed uevent variables
power-supply core:
* Add power-supply type in uevent
* Cleanup property handling in core
* Make property and usb_type pointers const
* Convert core power-supply DT binding to YAML
* Cleanup HWMON code
* Add new health status "calibration required"
* Add new properties for manufacture date and
capacity error margin
battery drivers:
* new cw2015 battery driver used by pine64 Pinebook Pro laptop
* axp22: blacklist on Meegopad T02
* sc27xx: support current/voltage reading
* max17042: support time-to-empty reading
* simple-battery: add more battery parameters
* bq27xxx: convert DT binding document to YAML
* sbs-battery: add TI BQ20Z65 support, fix technology property, convert
DT binding to YAML, add option to disable charger
broadcasts, add new properties: manufacture date,
capacity error margin, average current, charge current
and voltage and support calibration required health
status
* misc. fixes
charger drivers:
* bq25890: cleanup, implement charge type, precharge current and input
current limiting properties
* bd70528: use new linear range helper library
* bd99954: new charger driver
* mp2629: new charger driver
* misc. fixes
reboot drivers:
* oxnas-restart: introduce new driver
* syscon-reboot: convert DT binding to YAML, add parent syscon device support
* misc. fixes
-----BEGIN PGP SIGNATURE-----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=He9L
-----END PGP SIGNATURE-----
Merge tag 'for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"This time there are lots of changes. Quite a few changes to the core,
lots of driver changes and one change to kobject core (with Ack from
Greg).
Summary:
kobject:
- Increase number of allowed uevent variables
power-supply core:
- Add power-supply type in uevent
- Cleanup property handling in core
- Make property and usb_type pointers const
- Convert core power-supply DT binding to YAML
- Cleanup HWMON code
- Add new health status "calibration required"
- Add new properties for manufacture date and capacity error margin
battery drivers:
- new cw2015 battery driver used by pine64 Pinebook Pro laptop
- axp22: blacklist on Meegopad T02
- sc27xx: support current/voltage reading
- max17042: support time-to-empty reading
- simple-battery: add more battery parameters
- bq27xxx: convert DT binding document to YAML
- sbs-battery: add TI BQ20Z65 support, fix technology property,
convert DT binding to YAML, add option to disable charger
broadcasts, add new properties: manufacture date, capacity
error margin, average current, charge current and voltage and
support calibration required health status
- misc fixes
charger drivers:
- bq25890: cleanup, implement charge type, precharge current and
input current limiting properties
- bd70528: use new linear range helper library
- bd99954: new charger driver
- mp2629: new charger driver
- misc fixes
reboot drivers:
- oxnas-restart: introduce new driver
- syscon-reboot: convert DT binding to YAML, add parent syscon device
support
- misc fixes"
* tag 'for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (85 commits)
power: supply: cw2015: Attach OF ID table to the driver
power: reset: gpio-poweroff: add missing '\n' in dev_err()
Revert "power: supply: sbs-battery: simplify read_read_string_data"
Revert "power: supply: sbs-battery: add PEC support"
dt-bindings: power: sbs-battery: Convert to yaml
power: supply: sbs-battery: constify power-supply property array
power: supply: sbs-battery: switch to i2c's probe_new
power: supply: sbs-battery: switch from of_property_* to device_property_*
power: supply: sbs-battery: add ability to disable charger broadcasts
power: supply: sbs-battery: fix idle battery status
power: supply: sbs-battery: add POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED support
power: supply: sbs-battery: add MANUFACTURE_DATE support
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT/VOLTAGE_MAX support
power: supply: sbs-battery: Improve POWER_SUPPLY_PROP_TECHNOLOGY support
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CURRENT_AVG support
power: supply: sbs-battery: add PEC support
power: supply: sbs-battery: simplify read_read_string_data
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CAPACITY_ERROR_MARGIN support
power: supply: sbs-battery: Add TI BQ20Z65 support
power: supply: core: add POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED
...
It appears that OF ID table was hanging around without being attached
to the driver. Attach it properly.
Fixes: b4c7715c10 ("power: supply: add CellWise cw2015 fuel gauge driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-By: Tobias Schramm <t.schramm@manjaro.org>
Tested-By: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already supported
in arch/arm64. The platform may also be extended to support running
32-bit kernels on those 64-bit chips for memory-constrained machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or R8A7742,
an eight-core chip based on Cortex-A15 and Cortex-A7 cores, originally
released in 2016 as one of the last high-end 32-bit designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater effort
for the Android OS to have a common kernel binary for all platforms and
any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining.
All device drivers specific to those boards can now get removed as
well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gzCp
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"One new platform gets added, the Realtek RTD1195, which is an older
Cortex-a7 based relative of the RTD12xx chips that are already
supported in arch/arm64. The platform may also be extended to support
running 32-bit kernels on those 64-bit chips for memory-constrained
machines.
In the Renesas shmobile platform, we gain support for "RZ/G1H" or
R8A7742, an eight-core chip based on Cortex-A15 and Cortex-A7 cores,
originally released in 2016 as one of the last high-end 32-bit
designs.
There is ongoing cleanup for the integrator, tegra, imx, and omap2
platforms, with integrator getting very close to the goal of having
zero code in arch/arm/, and omap2 moving more of the chip specifics
from old board code into device tree files.
The Versatile Express platform is made more modular, with built-in
drivers now becoming loadable modules. This is part of a greater
effort for the Android OS to have a common kernel binary for all
platforms and any platform specific code in loadable modules.
The PXA platform drops support for Compulab's pxa2xx boards that had
rather unusual flash and PCI drivers but no known users remaining. All
device drivers specific to those boards can now get removed as well.
Across platforms, there is ongoing cleanup, with Geert and Rob
revisiting some a lot of Kconfig options"
* tag 'arm-soc-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
ARM: omap2: fix omap5_realtime_timer_init definition
ARM: zynq: Don't select CONFIG_ICST
ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs
clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE
ARM: davinci: fix build failure without I2C
power: reset: vexpress: fix build issue
power: vexpress: cleanup: use builtin_platform_driver
power: vexpress: add suppress_bind_attrs to true
Revert "ARM: vexpress: Don't select VEXPRESS_CONFIG"
MAINTAINERS: pxa: remove Compulab arm/pxa support
ARM: pxa: remove Compulab pxa2xx boards
bus: arm-integrator-lm: Fix return value check in integrator_ap_lm_probe()
soc: imx: move cpu code to drivers/soc/imx
ARM: imx: move cpu definitions into a header
ARM: imx: use device_initcall for imx_soc_device_init
ARM: imx: pcm037: make pcm970_sja1000_platform_data static
bus: ti-sysc: Timers no longer need legacy quirk handling
ARM: OMAP2+: Drop old timer code for dmtimer and 32k counter
ARM: dts: Configure system timers for omap2
ARM: dts: Configure system timers for ti81xx
...
- Constify 'properties' attribute in core header file
- New Drivers
- Add support for Gateworks System Controller
- Add support for MediaTek MT6358 PMIC
- Add support for Mediatek MT6360 PMIC
- Add support for Monolithic Power Systems MP2629 ADC and Battery charger
- Rework Intel's SCU IPC collection
- Eliminate near duplicate IPC functionality
- Split out MFD related activities into a dedicated MFD driver
- Fix-ups
- Use new I2C API; htc-i2cpld
- Remove superfluous code; sprd-sc27xx-spi
- Improve error handling; stm32-timers
- Device Tree additions/fixes; mt6397
- Defer probe betterment; wm8994-core
- Improve module handling; wm8994-core
- Staticify; stpmic1
- Trivial (spelling, formatting); tqmx86
- Bug Fixes
- Fix incorrect register/PCI IDs; intel-lpss-pci
- Fix unbalanced Regulator API calls; wm8994-core
- Fix double free(); wcd934x
- Remove IRQ domain on failure; stmfx
- Reset chip on resume; stmfx
- Disable/enable IRQs on suspend/resume; stmfx
- Do not use bulk writes on H/W which does not support them; max77620
-----BEGIN PGP SIGNATURE-----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=746a
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Constify 'properties' attribute in core header file
New Drivers:
- Add support for Gateworks System Controller
- Add support for MediaTek MT6358 PMIC
- Add support for Mediatek MT6360 PMIC
- Add support for Monolithic Power Systems MP2629 ADC and Battery charger
Fix-ups:
- Use new I2C API in htc-i2cpld
- Remove superfluous code in sprd-sc27xx-spi
- Improve error handling in stm32-timers
- Device Tree additions/fixes in mt6397
- Defer probe betterment in wm8994-core
- Improve module handling in wm8994-core
- Staticify in stpmic1
- Trivial (spelling, formatting) in tqmx86
Bug Fixes:
- Fix incorrect register/PCI IDs in intel-lpss-pci
- Fix unbalanced Regulator API calls in wm8994-core
- Fix double free() in wcd934x
- Remove IRQ domain on failure in stmfx
- Reset chip on resume in stmfx
- Disable/enable IRQs on suspend/resume in stmfx
- Do not use bulk writes on H/W which does not support them in max77620"
* tag 'mfd-next-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (29 commits)
mfd: mt6360: Remove duplicate REGMAP_IRQ_REG_LINE() entry
mfd: Add support for PMIC MT6360
mfd: max77620: Use single-byte writes on MAX77620
mfd: wcd934x: Drop kfree for memory allocated with devm_kzalloc
mfd: stmfx: Disable IRQ in suspend to avoid spurious interrupt
mfd: stmfx: Fix stmfx_irq_init error path
mfd: stmfx: Reset chip on resume as supply was disabled
mfd: wm8994: Silence warning about supplies during deferred probe
mfd: wm8994: Fix unbalanced calls to regulator_bulk_disable()
mfd: wm8994: Fix driver operation if loaded as modules
dt-bindings: mfd: mediatek: Add MT6397 Pin Controller
mfd: Constify properties in mfd_cell
mfd: stm32-timers: Use dma_request_chan() instead dma_request_slave_channel()
mfd: sprd: Remove unnecessary spi_bus_type setting
mfd: intel-lpss: Update LPSS UART #2 PCI ID for Jasper Lake
mfd: tqmx86: Fix a typo in MODULE_DESCRIPTION
mfd: stpmic1: Make stpmic1_regmap_config static
mfd: htc-i2cpld: Convert to use i2c_new_client_device()
MAINTAINERS: Add entry for mp2629 Battery Charger driver
power: supply: mp2629: Add impedance compensation config
...
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
The commit is a nice cleanup, but breaks booting on exynos5 based
chromebooks. It's seems to come down to exynos5's i2c driver not
implementing I2C_FUNC_SMBUS_READ_BLOCK_DATA. It's not yet clear
why that breaks boot / massively slows it down when userspace
starts, so revert the problematic patch.
This reverts commit c4b12a2f3f.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This depends on the simplification of sbs_read_string_data, which
breaks booting exynos5 based chromebooks. More investigation is
required, so this patch and the simplification patch are reverted
for this merge window.
Note, that this is only a partial revert, since sbs_update_presence()
has not been removed. It is also required for the charger broadcast
disabling.
This reverts commit 79bcd5a4a6.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Switch from DT specific of_property_* API to generic and more
modern device_property_* API.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In certain designs, it is possible to add a battery on a populated i2c
bus without an sbs compliant charger. In that case, the battery will
unnecessarily and sometimes undesirably master the bus trying to write
info in the charger.
It is observed in many occasion that these battery "broadcasts" are even
corrupting other ongoing master to slave communication. I.e. the
multi-master support in the battery is inadequate.
Thankfully, the CHARGER_MODE bit allows designers to disable that SBS
battery behaviour.
This needs to be done once when the battery is first seen on the bus.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
[rebased code]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
A battery, that is neither charged, nor discharged is not
always Full. If the charger is disabled for other reasons
it might simply be idle and should be marked accordingly.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for reporting the SBS battery's condition flag
to userspace using the new "Calibration required" health status.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Expose the battery's manufacture date to userspace.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Expose maximum charge current/voltage information requested
by the battery.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This reads the battery chemistry from the battery chip instead
of incorrectly hardcoding the type to be Li-Ion.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Expose averaged current information, which is part of the SBS
standard and should be supported by all batteries.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SBS batteries optionally have support for PEC. This enables
PEC handling based on the implemented SBS version as suggested
by the standard. The support for PEC is re-evaluated when the
battery is hotplugged into the system, since there might be
systems supporting batteries from different SBS generations.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The SBS battery implements SMBus block reads. Currently the
driver "emulates" this by doing an I2C byte read for the
length followed by an I2C block read. The I2C subsystem
actually provides a proper API for doing SMBus block reads,
which can and should be used instead. The current implementation
does not properly handle packet error checking (PEC).
This change requires, that I2C bus drivers support I2C_M_RECV_LEN
or directly provide the SMBus API to access device manufacturer
and model name.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for reporting the MaxError register from
battery fuel gauges following the smart battery standard.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for BQ20Z65 manufacturer data to the sbs-battery
driver. Implementation has been verified using the public TRM
available from [0] and tested using a GE Flex 3S2P battery.
[0] http://www.ti.com/lit/pdf/sluu386
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some battery fuel gauges know when the battery needs to
be recalibrated before providing usable values. This
should be reported via the health property.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some smart batteries store their manufacture date, which is
useful to identify the battery and/or to know about the cell
quality.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following sparse warning:
drivers/power/supply/bd99954-charger.c:1028:6: warning: symbol 'bd9995x_chip_reset' was not declared.
The bd9995x_chip_reset() has only one call site within bd99954-charger.c
It should be static
Fixes: 0902f83664 ("power: supply: Support ROHM bd99954 charger")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
An allmodconfig kernel makes CONFIG_VEXPRESS_CONFIG a module and
CONFIG_POWER_RESET_VEXPRESS builtin. That makes us see this build
error:
aarch64-linux-gnu-ld: drivers/power/reset/vexpress-poweroff.o: in function `vexpress_reset_probe':
../drivers/power/reset/vexpress-poweroff.c:119: undefined reference to `devm_regmap_init_vexpress_config'
../drivers/power/reset/vexpress-poweroff.c:119:(.text+0x48c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol
`devm_regmap_init_vexpress_config'
make[1]: *** [/srv/src/kernel/next/Makefile:1126: vmlinux] Error 1
Rework so that POWER_RESET_VEXPRESS depends on 'VEXPRESS_CONFIG=y'.
Link: https://lore.kernel.org/r/20200527112608.3886105-5-anders.roxell@linaro.org
Fixes: d06cfe3f12 ("bus: vexpress-config: Merge vexpress-syscfg into vexpress-config")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the helper macro for builtin drivers taht don't do anything special
in driver init. This removes some boilerplate code.
Link: https://lore.kernel.org/r/20200527112608.3886105-3-anders.roxell@linaro.org
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Make sure that the POWER_RESET_VEXPRESS driver won't have bind/unbind
attributes available via the sysfs, so lets be explicit here and use
".suppress_bind_attrs = true" to prevent userspace from doing something
silly.
Link: https://lore.kernel.org/r/20200527112608.3886105-2-anders.roxell@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add device tree compatible strings and create proper modalias structures
to let this driver load automatically if compiled as module, because
max14577 MFD driver creates MFD cells with such compatible strings.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=89mP
-----END PGP SIGNATURE-----
Merge tag 'tags/ib-mfd-iio-power-v5.8' into psy-next
This merges the MP2629 battery charge management immutable branch
between MFD, IIO and power-supply due for the v5.8 merge window
into power-supply for-next branch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since normally syscon-reboot block is supposed to be a part of a system
controller, lets look for the syscon regmap in a parental DT node if
regmap property isn't specified. DT binding from now considers the regmap
property as deprecated.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The mp2629 provides switching-mode battery charge management for
single-cell Li-ion or Li-polymer battery. Driver supports the
access/control input source and battery charging parameters.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This add support for the MediaTek MT6358 RTC. Driver using
compatible data to store different RTC_WRTGR address offset.
This replace RTC_WRTGR to RTC_WRTGR_MT6323 in mt6323-poweroff
driver which only needed by armv7 CPU without ATF.
Signed-off-by: Ran Bi <ran.bi@mediatek.com>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move away from the deprecated API in this comment.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Report REG00.IINLIM value as INPUT_CURRENT_LIMIT property.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Report charging type based on recently read state.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Edge interrupts from the charger may be lost or stuck in fault mode
since probe(). Check if something changed everytime userspace wants
some data.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Datasheet describes two modes for reading ADC measurements:
1. continuous, 1 Hz - enabled and started by CONV_RATE bit
2. one-shot - triggered by CONV_START bit
In continuous mode, CONV_START is read-only and signifies an ongoing
conversion.
Change the code to follow the datasheet and really disable continuous
mode for power saving.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Charge Current is more apropriately reflected by CURRENT_NOW property
(measured current) than CONSTANT_CURRENT_VOLTAGE (configured CC-phase
current limit). Fix the reference and make the sign reflect direction
of the current.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
According to the datasheet available at (1), the bottom four
bits are always zero and the actual voltage is 1.25x this value
in mV. Since the kernel API specifies that voltages should be in
uV, it should report 1250x the shifted value.
1) https://datasheets.maximintegrated.com/en/ds/MAX17040-MAX17041.pdf
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The framework is unhappy about them, because it uses the names in sysfs
attributes:
power_supply olpc-ac: hwmon: 'olpc-ac' is not a valid name attribute, please fix
power_supply olpc-battery: hwmon: 'olpc-battery' is not a valid name attribute, please fix
See also commit 648cd48c9e ("hwmon: Do not accept invalid name
attributes") and commit 74d3b64197 ("hwmon: Relax name attribute
validation for new APIs").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This delay-fix is picked up from downstream driver,
we measured that 25 - 35 ms delay ensure that we get required data.
Tested on SMB347 on Nexus 7 2012. Otherwise IRQSTAT_E fails to provide
correct information.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix failure when USB cable is connected:
smb347 2-006a: reading IRQSTAT_D failed
Fixes: 1502cfe19b ("smb347-charger: Fix battery status reporting logic for charger faults")
Tested-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The "default n" is not needed as it is, well, default. Clean
the KConfig by removing "default n".
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Indent the help text as explained in
Documentation/process/coding-style.rst
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion
secondary battery intended to be used in space-constraint equipment such
as Low profile Notebook PC, Tablets and other applications. BD99954
provides a Dual-source Battery Charger, two port BC1.2 detection and a
Battery Monitor.
Support ROHM BD99954 Charger IC.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Change the bd70528 to use common linear_range code instead of
implementing a copy of it in this driver.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl61lKwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HxeB/9dblIbC+28MvcEHXCcYBZBouOnrM8E
bIOMXkgEj1uL78ozOm7tMCgEpaKgv6BHdDuClCBvjbr0uOtAi0qUiv0IBotuVrdo
lq73l8l7OPz6TFFKIt8WsgwKnzdkuQC08+qrZasAdluRQnqnmkU2tvl2y9zaaaR4
6hGw+Nwx/pgeCXCa3pu+rCYwA7g0Tf8a6DDC6LyQWZameBJ1ey/YDjhJEeSmY7P7
306zs8YVxHhQMLUQ5T7DA6r/KWMNkO1SOueCqTjxWZc/XamGEcbsZG1cWrAnkoE2
VKLXBtYC75coNxIiu8ZxnQwLLdz1EQPdtg0qmzSjXJ68QjbWWzf4K1ra
=LG9G
-----END PGP SIGNATURE-----
Merge tag 'tags/linear-ranges-lib' into psy-next
lib: Add linear ranges helper library and start using it
Series extracts a "linear ranges" helper out of the regulator
framework. Linear ranges helper is intended to help converting
real-world values to register values when conversion is linear. I
suspect this is useful also for power subsystem and possibly for clk.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix gcc '-Wunused-but-set-variable' warning:
drivers/power/reset/ltc2952-poweroff.c:97:16: warning: variable
‘overruns’ set but not used [-Wunused-but-set-variable]
unsigned long overruns;
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the probe function, in case of error, resources allocated in
'lp8788_setup_adc_channel()' must be released.
This can be achieved easily by using the devm_ variant of
'iio_channel_get()'.
This has the extra benefit to simplify the remove function and to axe the
'lp8788_release_adc_channel()' function which is now useless.
Fixes: 98a2766493 ("power_supply: Add new lp8788 charger driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following warning:
drivers/power/supply/cw2015_battery.c:96:5: warning:
'cw_update_profile' was not declared. Should it be static?
drivers/power/supply/cw2015_battery.c:712:1: warning:
'cw_bat_pm_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenTao <chentao107@huawei.com>
Acked-by: Tobias Schramm <t.schramm@manjaro.org>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We introduced some new locking here, but need to update the error
paths so they unlock before returning.
Fixes: 72d9cd9cdc ("power: bq25890: protect view of the chip's state")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add POWER_SUPPLY_TYPE to the uevent env for power supply. Type is a
property of all power supplies and there is a sysfs entry for it but it
is not included in the properties array of the power supply so
explicitly add it to the udev env.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reduce the number of touch points to add a new enum property to the
power_supply class by mapping the array of text values to the device
attribute descriptor. A new enum property can now added by creating an
array with the text values named POWER_SUPPLY_${PROPNAME}_TEXT and
adding POWER_SUPPLY_ENUM_ATTR(${PROPNAME}) to the power_supply_attrs
array.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use designated initializers for the sysfs power supply text values. This
will help ensure that the text values are kept in sync with the enum
values from power_supply.h.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make the device attribute list used to create sysfs attributes more
robust by decoupling the list order from order of the enum defined in
power_supply.h. This is done by using a designated initializer in the
POWER_SUPPLY_ATTR macro.
Signed-off-by: Mathew King <mathewk@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Extend bq->lock over whole updating of the chip's state. Might get
useful later for switching ADC modes correctly.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
regmap initialization will check I2C adapter functionality.
Remove redundant check in the driver.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Property list should not change, so mark it const.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Driver rejects unknown chips early in the probe(), so when
bq25890_power_supply_get_property() is made reachable, bq->chip_version
will already be set to correct value - there is no need to check
it again.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds a driver for the CellWise cw2015 fuel gauge.
The CellWise cw2015 is a shuntless, single-cell Li-Ion fuel gauge used
in the pine64 Pinebook Pro laptop and some Raspberry Pi UPS HATs.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In function power_supply_add_hwmon_sysfs(), psyhw->props is
allocated by bitmap_zalloc(). But this pointer is not deallocated
when devm_add_action fail, which lead to a memory leak bug. To fix
this, we replace devm_add_action with devm_add_action_or_reset.
Cc: stable@kernel.org
Fixes: e67d4dfc9f ("power: supply: Add HWMON compatibility layer")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Rework power_supply_hwmon_read_string() to check it's parameters.
This allows to extend it later with labels for other types of
measurements.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Initialize num_properties with length of the copied array instead
of relying on previously memcpy'd value. This makes it clear how
the array and the counter are related.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently HWMON emulation shows all labels (temp and ambient temp)
regardless if power supply supports reading the values. Check that at
least one property is enabled for each label.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
tempX_label files are swapped compared to what
power_supply_hwmon_temp_to_property() uses. Make them match.
Cc: stable@vger.kernel.org
Fixes: e67d4dfc9f ("power: supply: Add HWMON compatibility layer")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This prepares the driver to work with the properties entry
in power_supply_desc marked as const.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This prepares the driver to work with the properties entry
in power_supply_desc marked as const.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reduce power_supply_show_usb_type() parameter count by folding
power_supply_desc dereference into the function. This makes following
patch making usb_types const easier.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add reboot handler for Oxford OX820 chips as reboot currenly hangs on
those boards. Code is based on ox820_assert_system_reset() found in
https://github.com/kref/linux-oxnas.git in
arch/arm/mach-oxnas/mach-ox820.c line 181.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The max170{42,47,50,55} family of fuel gauges all provide time-to-empty
estimation. As such, let's export this as a property.
Signed-off-by: Geordan Neukum <gneukum1@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the axp288_charger_probe(), when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Shengju Zhang <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add new property to allow to get the voltage measured during boot time.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add new properties to get present current and voltage of the fuel gauge.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The battery full capacity can be affected by the temperature or the
servicing time or other factors, so some platforms will track the
real battery full capacity in charger manager service. Thus we should
allow to change the battery full capacity by setting the
'POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN' property as writeable.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is no thermal zone should be created for the SC27XX FGU power supply,
thus set the 'no_thermal' flag as true.
Signed-off-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following coccicheck warning:
drivers/power/supply/ab8500_fg.c:2402:5-24: WARNING: Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of hardcode the mask, it should be depends
on which generation of pon it was.
Signed-off-by: Kejia Hu <kejia.hu@codethink.co.uk>
Fixes: fce5430f6a ("reset: qcom-pon: Add support for gen2 pon")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Get rid of linux/vermagic.h includes, so that MODULE_ARCH_VERMAGIC from
the arch header arch/x86/include/asm/module.h won't be redefined.
In file included from ./include/linux/module.h:30,
from drivers/net/ethernet/3com/3c515.c:56:
./arch/x86/include/asm/module.h:73: warning: "MODULE_ARCH_VERMAGIC"
redefined
73 | # define MODULE_ARCH_VERMAGIC MODULE_PROC_FAMILY
|
In file included from drivers/net/ethernet/3com/3c515.c:25:
./include/linux/vermagic.h:28: note: this is the location of the
previous definition
28 | #define MODULE_ARCH_VERMAGIC ""
|
Fixes: 6bba2e89a8 ("net/3com: Delete driver and module versions from 3com drivers")
Co-developed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Shannon Nelson <snelson@pensando.io> # ionic
Acked-by: Sebastian Reichel <sre@kernel.org> # power
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the pm860x_battery_probe(), when get irq failed, the function
platform_get_irq() logs an dev_err message, so remove redundant
message here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Meegopad T02 is a PC in stick format and doesn't have a battery,
it is reported with a random and constant battery charge but as
discharging to userspace.
Add it to the blacklist to avoid the bogus battery status reporting.
Signed-off-by: Rafael Gandolfi <rafirafi.at@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following gcc warning:
drivers/power/supply/max14656_charger_detector.c:142:6: warning:
variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret = 0;
^~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
regmap is a library function that gets selected by drivers that need
it. No driver modules should depend on it. Depending on REGMAP_I2C makes
this driver only build if another driver already selected REGMAP_I2C,
as the symbol can't be selected through the menu kernel configuration.
Fixes: 2219a93596 ("power_supply: Add TI BQ24257 charger driver")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
For security reasons I stopped using gmail account and kernel address is
now up-to-date alias to my personal address.
People periodically send me emails to address which they found in source
code of drivers, so this change reflects state where people can contact
me.
[ Added .mailmap entry as per Joe Perches - Linus ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Link: http://lkml.kernel.org/r/20200307104237.8199-1-pali@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* cros-usbpd-notify and cros_ec_typec
- Add a new notification driver that handles and dispatches USB PD
related events to other drivers.
- Add a Type C connector class driver for cros_ec
* CrOS EC
- Introduce a new cros_ec_cmd_xfer_status helper
* Sensors/iio:
- A series from Gwendal that adds Cros EC sensor hub FIFO support
* Wilco EC
- Fix a build warning.
- Platform data shouldn't include kernel.h
* Misc
- i2c api conversion complete, with i2c_new_client_device instead of
i2c_new_device in chromeos_laptop.
- Replace zero-length array with flexible-array member in cros_ec_chardev
and wilco_ec
- Update new structure for SPI transfer delays in cros_ec_spi
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXo1lfQAKCRBzbaomhzOw
wo6TAQCKHOcrqq5Y9HYXs1QBx8e/0vVwe5Jh76Qi6hUVqXu56QEA65lBZ2ni8Udp
f6jQDFkaeYaF2tkghvuNoAkFRI6/rAk=
=j4Tt
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
cros-usbpd-notify and cros_ec_typec:
- Add a new notification driver that handles and dispatches USB PD
related events to other drivers.
- Add a Type C connector class driver for cros_ec
CrOS EC:
- Introduce a new cros_ec_cmd_xfer_status helper
Sensors/iio:
- A series from Gwendal that adds Cros EC sensor hub FIFO support
Wilco EC:
- Fix a build warning.
- Platform data shouldn't include kernel.h
Misc:
- i2c api conversion complete, with i2c_new_client_device instead of
i2c_new_device in chromeos_laptop.
- Replace zero-length array with flexible-array member in
cros_ec_chardev and wilco_ec
- Update new structure for SPI transfer delays in cros_ec_spi
* tag 'tag-chrome-platform-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: (34 commits)
platform/chrome: cros_ec_spi: Wait for USECS, not NSECS
iio: cros_ec: Use Hertz as unit for sampling frequency
iio: cros_ec: Report hwfifo_watermark_max
iio: cros_ec: Expose hwfifo_timeout
iio: cros_ec: Remove pm function
iio: cros_ec: Register to cros_ec_sensorhub when EC supports FIFO
iio: expose iio_device_set_clock
iio: cros_ec: Move function description to .c file
platform/chrome: cros_ec_sensorhub: Add median filter
platform/chrome: cros_ec_sensorhub: Add code to spread timestmap
platform/chrome: cros_ec_sensorhub: Add FIFO support
platform/chrome: cros_ec_sensorhub: Add the number of sensors in sensorhub
platform/chrome: chromeos_laptop: make I2C API conversion complete
platform/chrome: wilco_ec: event: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_chardev: Replace zero-length array with flexible-array member
platform/chrome: cros_ec_typec: Update port info from EC
platform/chrome: Add Type C connector class driver
platform/chrome: cros_usbpd_notify: Pull PD_HOST_EVENT status
platform/chrome: cros_usbpd_notify: Amend ACPI driver to plat
platform/chrome: cros_usbpd_notify: Add driver data struct
...
Core:
* Nothing
Drivers:
* at91-reset: cleanups, proper handling for sam9x60
* sc27xx, charger-manager: allow building as module
* sc27xx: add support to read current charge capacity
* axp288: more quirks for weird hardware
* misc. fixes
-----BEGIN PGP SIGNATURE-----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=BCS7
-----END PGP SIGNATURE-----
Merge tag 'for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset changes from Sebastian Reichel:
"Core:
- Nothing
Drivers:
- at91-reset: cleanups, proper handling for sam9x60
- sc27xx, charger-manager: allow building as module
- sc27xx: add support to read current charge capacity
- axp288: more quirks for weird hardware
- misc fixes"
* tag 'for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (26 commits)
power: reset: sc27xx: Allow the SC27XX poweroff driver building into a module
power: reset: sc27xx: Change to use cpu_down()
power: reset: sc27xx: Power off the external subsystems' connection
power: twl4030: Use scnprintf() for avoiding potential buffer overflow
power: supply: bq27xxx_battery: Silence deferred-probe error
power: reset: at91-reset: handle nrst async for sam9x60
power: reset: at91-reset: get rid of at91_reset_data
power: reset: at91-reset: keep only one reset function
power: reset: at91-reset: make at91sam9g45_restart() generic
power: reset: at91-reset: introduce ramc_lpr to struct at91_reset
power: reset: at91-reset: use r4 as tmp argument
power: reset: at91-reset: introduce args member in at91_reset_data
power: reset: at91-reset: introduce struct at91_reset_data
power: reset: at91-reset: devm_kzalloc() for at91_reset data structure
power: reset: at91-reset: pass rstc base address to at91_reset_status()
power: reset: at91-reset: convert reset in pointer to struct at91_reset
power: reset: at91-reset: add notifier block to struct at91_reset
power: reset: at91-reset: add sclk to struct at91_reset
power: reset: at91-reset: add ramc_base[] to struct at91_reset
power: reset: at91-reset: introduce struct at91_reset
...
Change the config to 'tristate' and use module_platform_driver() to
allow the SC27XX poweroff driver building into a module, as well as
adding some mudule information.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
To allow the SC27XX driver can be built as a module, and the
freeze_secondary_cpus() symbol is not exported, thus we can change
to use the exported cpu_down() API to shut down other cpus to avoid
racing, which is same as the freeze_secondary_cpus().
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When powering off the whole system, we should power off some external
subsystems' connection firstly, otherwise some external subsystems
will hold some power and result in powering down abnormally.
Signed-off-by: Sherry Zong <sherry.zong@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver fails to probe with -EPROBE_DEFER if battery's power supply
(charger driver) isn't ready yet and this results in a bit noisy error
message in KMSG during kernel's boot up. Let's silence the harmless
error message.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Handle NRST asynchronously for SAM9X60 to avoid problem with fast drop of
VDDCORE on shutdown operations in the first 100 us after CPU is shutdown.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
After refactoring struct at91_reset_data and
struct at91_reset_data at91sam9260_reset_data are not needed anymore.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Keep only one reset function. With this, notifier_call member of
struct at91_reset_data could be removed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce ramc_lpr to struct at91_reset. This will lead to the
unification of at91sam9260_restart() and at91sam9g45_restart().
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use r4 as temporary register. On ARM r0-r3 should be used to hold
function arguments.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce args member in struct at91_reset_data. It stores the value
that needs to be written in mode register so that the reboot actions
to happen. With these changes samx7_restart() could be removed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce struct at91_reset_data to be able to provide per SoC
data. At the moment this being only notifier callback.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Allocate at91_reset data on probe and set it as platform data.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add new argument to at91_reset_status() that is the pointer to reset
controller base address.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Convert reset in pointer to struct at91_reset.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Introduce struct at91_reset intended to keep all the at91 reset controller
data.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some HP Pavilion x2 10 models use an AXP288 for charging and fuel-gauge.
We use a native power_supply / PMIC driver in this case, because on most
models with an AXP288 the ACPI AC / Battery code is either completely
missing or relies on custom / proprietary ACPI OpRegions which Linux
does not implement.
The native drivers mostly work fine, but there are 2 problems:
1. These model uses a Type-C connector for charging which the AXP288 does
not support. As long as a Type-A charger (which uses the USB data pins for
charger type detection) is used everything is fine. But if a Type-C
charger is used (such as the charger shipped with the device) then the
charger is not recognized.
So we end up slowly discharging the device even though a charger is
connected, because we are limiting the current from the charger to 500mA.
To make things worse this happens with the device's official charger.
Looking at the ACPI tables HP has "solved" the problem of the AXP288 not
being able to recognize Type-C chargers by simply always programming the
input-current-limit at 3000mA and relying on a Vhold setting of 4.7V
(normally 4.4V) to limit the current intake if the charger cannot handle
this.
2. If no charger is connected when the machine boots then it boots with the
vbus-path disabled. On other devices this is done when a 5V boost converter
is active to avoid the PMIC trying to charge from the 5V boost output.
This is done when an OTG host cable is inserted and the ID pin on the
micro-B receptacle is pulled low, the ID pin has an ACPI event handler
associated with it which re-enables the vbus-path when the ID pin is pulled
high when the OTG cable is removed. The Type-C connector has no ID pin,
there is no ID pin handler and there appears to be no 5V boost converter,
so we end up not charging because the vbus-path is disabled, until we
unplug the charger which automatically clears the vbus-path disable bit and
then on the second plug-in of the adapter we start charging.
The HP Pavilion x2 10 models with an AXP288 do have mostly working ACPI
AC / Battery code which does not rely on custom / proprietary ACPI
OpRegions. So one possible solution would be to blacklist the AXP288
native power_supply drivers and add the HP Pavilion x2 10 with AXP288
DMI ids to the list of devices which should use the ACPI AC / Battery
code even though they have an AXP288 PMIC. This would require changes to
4 files: drivers/acpi/ac.c, drivers/power/supply/axp288_charger.c,
drivers/acpi/battery.c and drivers/power/supply/axp288_fuel_gauge.c.
Beside needing adding the same DMI matches to 4 different files, this
approach also triggers problem 2. from above, but then when suspended,
during suspend the machine will not wakeup because the vbus path is
disabled by the AML code when not charging, so the Vbus low-to-high
IRQ is not triggered, the CPU never wakes up and the device does not
charge even though the user likely things it is charging, esp. since
the charge status LED is directly coupled to an adapter being plugged
in and does not reflect actual charging.
This could be worked by enabling vbus-path explicitly from say the
axp288_charger driver's suspend handler.
So neither situation is ideal, in both cased we need to explicitly enable
the vbus-path to work around different variants of problem 2 above, this
requires a quirk in the axp288_charger code.
If we go the route of using the ACPI AC / Battery drivers then we need
modifications to 3 other drivers; and we need to partially disable the
axp288_charger code, while at the same time keeping it around to enable
vbus-path on suspend.
OTOH we can copy the hardcoding of 3A input-current-limit (we never touch
Vhold, so that would stay at 4.7V) to the axp288_charger code, which needs
changes regardless, then we concentrate all special handling of this
interesting device model in the axp288_charger code. That is what this
commit does.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1791098
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Intel Compute Stick `STK1A32SC` can have a system vendor of
"Intel(R) Client Systems".
Broaden the Intel Compute Stick DMI checks so that they match "Intel
Corporation" as well as "Intel(R) Client Systems".
This fixes an issue where the STK1A32SC compute sticks were still
exposing a battery with the existing blacklist entry.
Signed-off-by: Jeffery Miller <jmiller@neverware.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Allow charger manager can be built as a module like other charger
drivers.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add the POWER_SUPPLY_PROP_CHARGE_NOW attribute to allow user to get
current battery capacity (uAh) to do measurement.
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Don't print an error message if devm_power_supply_register() returns
-EPROBE_DEFER, since the driver will simply re-probe later.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There's a bug on ACPI platforms where host events from the ECPD ACPI
device never make their way to the cros-ec-usbpd-charger driver. This
makes it so the only time the charger driver updates its state is when
user space accesses its sysfs attributes.
Now that these events have been unified into a single notifier chain on
both ACPI and non-ACPI platforms, update the charger driver to use this
new notifier.
Reviewed-by: Benson Leung <bleung@chromium.org>
Co-Developed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Jon Flatley <jflat@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60.
-----BEGIN PGP SIGNATURE-----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=fIjZ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: OMAP2+: Fix undefined reference to omap_secure_init
ARM: s3c64xx: Drop unneeded select of TIMER_OF
ARM: exynos: Drop unneeded select of MIGHT_HAVE_CACHE_L2X0
ARM: s3c24xx: Switch to atomic pwm API in rx1950
ARM: OMAP2+: sleep43xx: Call secure suspend/resume handlers
ARM: OMAP2+: Use ARM SMC Calling Convention when OP-TEE is available
ARM: OMAP2+: Introduce check for OP-TEE in omap_secure_init()
ARM: OMAP2+: Add omap_secure_init callback hook for secure initialization
ARM: at91: Documentation: add sam9x60 product and datasheet
ARM: at91: pm: use of_device_id array to find the proper shdwc node
ARM: at91: pm: use SAM9X60 PMC's compatible
ARM: imx: only select ARM_ERRATA_814220 for ARMv7-A
ARM: zynq: use physical cpuid in zynq_slcr_cpu_stop/start
ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume
ARM: tegra: Modify reshift divider during LP1
ARM: tegra: Enable PLLP bypass during Tegra124 LP1
ARM: samsung: Rename Samsung and Exynos to lowercase
ARM: exynos: Correct the help text for platform Kconfig option
ARM: bcm: Select ARM_AMBA for ARCH_BRCMSTB
ARM: brcmstb: Add debug UART entry for 7216
...
Update the recently merged CPR (Core Power Reduction) support in the
AVS (Adaptive Voltage Scaling) subsystem (Brendan Higgins, Nathan
Chancellor, Niklas Cassel) and the rockchip-io AVS driver (Heiko
Stuebner), add two more module parameters to intel_idle on top of the
recently merged material, clean up a piece of cpuidle documentation
and consolidate system sleep states documentation (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----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=Yc9a
-----END PGP SIGNATURE-----
Merge tag 'pm-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
- Update the recently merged CPR (Core Power Reduction) support in the
AVS (Adaptive Voltage Scaling) subsystem (Brendan Higgins, Nathan
Chancellor, Niklas Cassel)
- Update the rockchip-io AVS driver (Heiko Stuebner)
- Add two more module parameters to intel_idle on top of the recently
merged material (Rafael Wysocki)
- Clean up a piece of cpuidle documentation and consolidate system
sleep states documentation (Rafael Wysocki)
* tag 'pm-5.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Documentation: Clean up PM QoS description
Documentation: admin-guide: PM: Update sleep states documentation
intel_idle: Introduce 'states_off' module parameter
intel_idle: Introduce 'use_acpi' module parameter
power: avs: qcom-cpr: Avoid clang -Wsometimes-uninitialized in cpr_scale
power: avs: qcom-cpr: add unspecified HAS_IOMEM dependency
PM / AVS: rockchip-io: fix the supply naming for the emmc supply on px30
power: avs: qcom-cpr: add a printout after the driver has been initialized
* CrOS EC
- Refactoring of some of cros_ec's headers. include/linux/mfd/cros_ec.h now
removed, new cros_ec.h added drivers/platform/chrome which contains shared
operations of cros_ec transport drivers.
- Response tracing in cros_ec_proto
* Wilco EC
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
* Misc
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCXjij4AAKCRBzbaomhzOw
wrFjAP0bU5PFkxprCOTY9kF/cMgHPDljEPES4FVV11eGyYr3HgD/StpuIhFGrh7+
Fz96dDdNu1melyGjmMqSN/M9JFo+Hw4=
=FB/I
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"CrOS EC:
- Refactoring of some of cros_ec's headers:
include/linux/mfd/cros_ec.h now removed, new cros_ec.h added to
drivers/platform/chrome which contains shared operations of cros_ec
transport drivers.
- Response tracing in cros_ec_proto
Wilco EC:
- Fix unregistration order.
- Fix keyboard backlight probing on systems without keyboard
backlight
- Minor cleanup (newlines in printks, COMPILE_TEST)
Misc:
- chromeos_laptop converted to use i2c_new_scanned_device instead of
i2c_new_probed_device"
* tag 'tag-chrome-platform-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec: Match implementation with headers
platform/chrome: cros_ec: Drop unaligned.h include
platform/chrome: wilco_ec: Allow wilco to be compiled in COMPILE_TEST
platform/chrome: wilco_ec: Add newlines to printks
platform/chrome: wilco_ec: Fix unregistration order
cros_ec: treewide: Remove 'include/linux/mfd/cros_ec.h'
platform/chrome: cros_ec_ishtp: Make init_lock static
platform/chrome: chromeos_laptop: Convert to i2c_new_scanned_device
platform/chrome: cros_ec_lpc: Use platform_get_irq_optional() for optional IRQs
platform/chrome: cros_ec_proto: Add response tracing
platform/chrome: cros_ec_trace: Match trace commands with EC commands
Clang warns (trimmed for brevity):
../drivers/power/avs/qcom-cpr.c:570:13: warning: variable 'reg_mask' is
used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
../drivers/power/avs/qcom-cpr.c:520:13: warning: variable 'new_uV' is
used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
Due to the fact that Clang's static analysis happens before any
optimization passes are taken into account, it cannot see that both
branches in the if statement must be taken because dir cannot be
something other than UP or DOWN due to the check at the top of this
function. Change the else if condition to else to fix this false
positive.
Fixes: bf6910abf5 ("power: avs: Add support for CPR (Core Power Reduction)")
Link: https://github.com/ClangBuiltLinux/linux/issues/840
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently CONFIG_QCOM_CPR=y implicitly depends on CONFIG_HAS_IOMEM=y;
consequently, on architectures without IOMEM we get the following build
error:
/usr/bin/ld: drivers/power/avs/qcom-cpr.o: in function `cpr_probe':
drivers/power/avs/qcom-cpr.c:1690: undefined reference to `devm_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The supply going to the emmc/flash is named vccio6, not vccio0 and while
the code does this correctly already, the comments and error output do not.
So just change these values to the correct ones.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to easier inform the user that the driver has been initialized
successfully, add a printout after the driver has been initialized.
At the same time, remove a dev_dbg() that is now redundant.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently a read failure by bq25890_field_read on F_DEV_REV is returning
an error in id instead of rev. Fix this by returning the value in rev.
Addresses-Coverity: ("Copy-paste error")
Fixes: d20267c9a9 ("power: supply: bq25890_charger: Add support of BQ25892 and BQ25896 chips")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Investigation on the AXP803 shows that VBUS_PLUGIN/VBUS_REMOVAL IRQs are
triggered on the rising/falling edge of AXP20X_PWR_STATUS_VBUS_USED. The
reason IRQs do not arrive while N_VBUSEN/DRIVEVBUS is high is because
AXP20X_PWR_STATUS_VBUS_USED also never goes high.
This also means that if VBUS is online, a VBUS_REMOVAL IRQ is received
immediately on setting N_VBUSEN/DRIVEVBUS high (and VBUS_PLUGIN shortly
after it is set back low). This was also verified to be the case when
manually offlining VBUS through AXP20X_VBUS_PATH_SELECT.
As long as VBUS is online, a present->absent transition necessarily
implies an online->offline transition. Since will cause an IRQ, there is
no need to poll while VBUS is online.
To ensure the driver's view of VBUS online status remains accurate,
unconditionally poll once when receiving an IRQ and when resuming. If
VBUS is still online at that time, polling will cease until the next
VBUS_REMOVAL IRQ.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The USB power supply input can be used as a wakeup source. Hook up the
VBUS_PLUGIN IRQ to trigger wakeup based on userspace configuration.
To do this, we must remember the list of IRQs for the life of the
device. To know how much space to allocate for the flexible array
member, we switch from using a NULL sentinel to using an array length.
Because we now depend on the specific order of the IRQs (we assume
VBUS_PLUGIN is first and always present), failing to acquire an IRQ
during probe must be a fatal error.
To avoid spuriously waking up the system when the USB power supply is
not configured as a wakeup source, we must explicitly disable all non-
wake IRQs during system suspend. This is because the SoC's NMI input is
shared among all IRQs on the AXP PMIC. Due to the use of regmap-irq, the
individual IRQs within the PMIC are nested threaded interrupts, and are
therefore not automatically disabled during system suspend.
The upshot is that if any other device within the MFD (such as the power
key) is an enabled wakeup source, all enabled IRQs within the PMIC will
cause wakeup. We still need to call enable_irq_wake() when we *do* want
wakeup, in case those other wakeup sources on the PMIC are all disabled.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
AXP803/AXP813 have a flag that enables/disables the USB power supply
input. Allow control of this flag via the ONLINE property on those
variants.
It may be necessary to offline the USB power supply input when using
the USB port in OTG mode, or to allow userspace to disable charging.
When the USB VBUS input is disabled via the PATH_SEL bit, the VBUS_USED
bit in PWR_INPUT_STATUS is cleared, so there is no change needed when
getting the property.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of ad-hoc variant ID checks throughout the code, let's start
moving the variant-specific details to a match structure. This allows
for future flexibility, and it better matches the other axp20x power
supply drivers.
This commit removes most variant checks from axp20x_usb_power_probe().
Other parts of the driver still do ID matching; they are left unchanged
for now.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following sparse warning:
drivers/power/supply/ucs1002_power.c:492:5: warning: symbol 'ucs1002_regulator_enable' was not declared. Should it be static?
Fixes: a3d70dacc7 ("power: suppy: ucs1002: disable power when max current is 0")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SAM9X60's PMC uses different offset for master clock register.
Add a member of type struct pmc_reg_config in struct reg_config,
fill it correspondingly for SAMA5D2 and SAM9X60 and use it in
poweroff() function.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver uses AT91_PMC_MCKR in poweroff() function. But the
SAM9X60's PMC versions maps AT91_PMC_MCKR functionality at different
offset compared to the SAMA5D2's one. This patch prepares the field
so that different AT91_PMC_MCKR's offsets to be introduced in
struct reg_config so that proper offset to be used for AT91_PMC_MCKR
based on compatible string.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add bq25892, bq25895 and bq25896 to list of supported device IDs for
DeviceTree and I2C.
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Support BQ25892 and BQ25896 chips by this driver. They shared one chip
ID 0, so distinquish them by device revisions (2 for 25896 and 1 for
25892).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The "mode" variable is an enum and in this context GCC treats it as an
unsigned int so the error handling is never triggered.
Fixes: 51d0756604 ("bq20z75: Add support for charge properties")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver's remove path calls cancel_delayed_work().
However, that function does not wait until the work function
finishes. This could mean that the work function is still
running after the driver's remove function has finished,
which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
that the work is properly cancelled, no longer running, and
unable to re-schedule itself.
This issue was detected with the help of Coccinelle.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Dan Murphy
Andrzej Pietrasiewicz
Jonathan Bakker
Dinghao Liu
Sebastian Reichel
Keyur Patel
Wang Qing
Linus Torvalds
Andy Shevchenko
Luca Ceresoli
Sebastian Reichel
Jean-Francois Dagenais
Samuel Zou
Anders Roxell
Marek Szyprowski
Serge Semin
Lee Jones
Saravanan Sekar
Ran Bi
Wolfram Sang
Michał Mirosław
Lubomir Rintel
David Heidelberg
Dmitry Osipenko
Matti Vaittinen
Hongbo Yao
Christophe JAILLET
ChenTao
Dan Carpenter
Mathew King
Tobias Schramm
Qiushi Wu
Daniel Golle
Geordan Neukum
Tang Bin
Yuanjiang Yu
Jason Yan
Kejia Hu
Leon Romanovsky
Rafael Gandolfi
Enric Balletbo i Serra
Pali Rohár
Baolin Wang
Sherry Zong
Takashi Iwai
Claudiu.Beznea@microchip.com
Hans de Goede
Jeffery Miller
Ashish Chavan
Paul Cercueil
Jon Flatley
Rafael J. Wysocki
Nathan Chancellor
Brendan Higgins
Heiko Stuebner
Niklas Cassel
Chen Zhou
Colin Ian King
Samuel Holland
Chen Wandun
Yauhen Kharuzhy
Sven Van Asbroeck