The Synopsys TSN MAC supports Qbv base times in the past, but only up to a
certain limit. As a result, a taprio qdisc configuration with a small
base time (for example when treating the base time as a simple phase
offset) is not applied by the hardware and silently ignored.
This was observed on an NXP i.MX8MPlus device, but likely affects all
TSN-variants of the MAC.
Fix the issue by making sure the base time is in the future, pushing it by
an integer amount of cycle times if needed. (a similar check is already
done in several other taprio implementations, see for example
drivers/net/ethernet/intel/igc/igc_tsn.c#L116 or
drivers/net/dsa/sja1105/sja1105_ptp.h#L39).
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210113131557.24651-2-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When configuring a 802.1Qbv schedule through the tc taprio qdisc on an NXP
i.MX8MPlus device, the effective cycle time differed from the requested one
by N*96ns, with N number of entries in the Qbv Gate Control List. This is
because the driver was adding a 96ns margin to each interval of the GCL,
apparently to account for the IPG. The problem was observed on NXP
i.MX8MPlus devices but likely affected all devices relying on the same
configuration callback (dwmac 4.00, 4.10, 5.10 variants).
Fix the issue by removing the margins, and simply setup the MAC with the
provided cycle time value. This is the behavior expected by the user-space
API, as altering the Qbv schedule timings would break standards conformance.
This is also the behavior of several other Ethernet MAC implementations
supporting taprio, including the dwxgmac variant of stmmac.
Fixes: 504723af0d ("net: stmmac: Add basic EST support for GMAC5+")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210113131557.24651-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the original mtu is not used when the mtu is updated,
the mtu is aligned with cache, this will get an incorrect.
For example, if you want to configure the mtu to be 1500,
but mtu 1536 is configured in fact.
Fixed: eaf4fac478 ("net: stmmac: Do not accept invalid MTU values")
Signed-off-by: David Wu <david.wu@rock-chips.com>
Link: https://lore.kernel.org/r/20210113034109.27865-1-david.wu@rock-chips.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use of __napi_schedule_irqoff() is not safe with PREEMPT_RT in which
hard interrupts are not disabled while running the threaded interrupt.
Using __napi_schedule() works for both PREEMPT_RT and mainline Linux,
just at the cost of an additional check if interrupts are disabled for
mainline (since they are already disabled).
Similar to the fix done for enetc commit 215602a8d2 ("enetc: use
napi_schedule to be compatible with PREEMPT_RT")
Signed-off-by: Seb Laveze <sebastien.laveze@nxp.com>
Link: https://lore.kernel.org/r/20210112140121.1487619-1-sebastien.laveze@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously, sun8i_dwmac_set_syscon was called from a chain of functions
in several different files:
sun8i_dwmac_probe
stmmac_dvr_probe
stmmac_hw_init
stmmac_hwif_init
sun8i_dwmac_setup
sun8i_dwmac_set_syscon
which made the lifetime of the syscon values hard to reason about. Part
of the problem is that there is no similar platform driver callback from
stmmac_dvr_remove. As a result, the driver unset the syscon value in
sun8i_dwmac_exit, but this leaves it uninitialized after a suspend/
resume cycle. It was also unset a second time (outside sun8i_dwmac_exit)
in the probe error path.
Move the init to the earliest available place in sun8i_dwmac_probe
(after stmmac_probe_config_dt, which initializes plat_dat), and the
deinit to the corresponding position in the cleanup order.
Since priv is not filled in until stmmac_dvr_probe, this requires
changing the sun8i_dwmac_set_syscon parameters to priv's two relevant
members.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sun8i_dwmac_exit calls sun8i_dwmac_unpower_internal_phy, but
sun8i_dwmac_init did not call sun8i_dwmac_power_internal_phy. This
caused PHY power to remain off after a suspend/resume cycle. Fix this by
recording if PHY power should be restored, and if so, restoring it.
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While stmmac_pltfr_remove calls sun8i_dwmac_exit, the sun8i_dwmac_init
and sun8i_dwmac_exit functions are also called by the stmmac_platform
suspend/resume callbacks. They may be called many times during the
device's lifetime and should not release resources used by the driver.
Furthermore, there was no error handling in case registering the MDIO
mux failed during probe, and the EPHY clock was never released at all.
Fix all of these issues by moving the deinitialization code to a driver
removal callback. Also ensure the EPHY is powered down before removal.
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_pltfr_remove does three things in one function, making it
inapproprate for unwinding the steps in the probe function. Currently,
a failure before the call to stmmac_dvr_probe would leak OF node
references due to missing a call to stmmac_remove_config_dt. And an
error in stmmac_dvr_probe would cause the driver to attempt to remove a
netdevice that was never added. Fix these by reordering the init and
splitting out the error handling steps.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Fixes: 40a1dcee2d ("net: ethernet: dwmac-sun8i: Use the correct function in exit path")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TGL-H PCI info and PCI IDs for the new TSN Controller to the list
of supported devices.
Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Link: https://lore.kernel.org/r/20201222160337.30870-1-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dwmac glue registers on Amlogic Meson8b and newer SoCs has two clock
inputs:
- Meson8b and Meson8m2: MPLL2 and MPLL2 (the same parent is wired to
both inputs)
- GXBB, GXL, GXM, AXG, G12A, G12B, SM1: FCLK_DIV2 and MPLL2
All known vendor kernels and u-boots are using the first input only. We
let the common clock framework automatically choose the "right" parent.
For some boards this causes a problem though, specificially with G12A and
newer SoCs. The clock input is used for generating the 125MHz RGMII TX
clock. For the two input clocks this means on G12A:
- FCLK_DIV2: 999999985Hz / 8 = 124999998.125Hz
- MPLL2: 499999993Hz / 4 = 124999998.25Hz
In theory MPLL2 is the "better" clock input because it's gets us 0.125Hz
closer to the requested frequency than FCLK_DIV2. In reality however
there is a resource conflict because MPLL2 is needed to generate some of
the audio clocks. dwmac-meson8b probes first and sets up the clock tree
with MPLL2. This works fine until the audio driver comes and "steals"
the MPLL2 clocks and configures it with it's own rate (294909637Hz). The
common clock framework happily changes the MPLL2 rate but does not
reconfigure our RGMII TX clock tree, which then ends up at 73727409Hz,
which is more than 40% off the requested 125MHz.
Don't use the second clock input for now to force the common clock
framework to always select the first parent. This mimics the behavior
from the vendor driver and fixes the clock resource conflict with the
audio driver on G12A boards. Once the common clock framework can handle
this situation this change can be reverted again.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: thomas graichen <thomas.graichen@gmail.com>
Link: https://lore.kernel.org/r/20201219135036.3216017-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Assign stmmac's mdio_bus probe capabilities to MDIOBUS_C22_C45.
This extended the probing of C45 PHY devices on the MDIO bus.
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IP register MAC_HW_Feature1[ADDR64] only defines
32/40/64 bit width, but some SOCs support others like i.MX8MP
support 34 bits but it maps to 40 bits width in MAC_HW_Feature1[ADDR64].
So overwrite dma_cap.addr64 according to HW real design.
Fixes: 94abdad697 ("net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chip")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have chance to re-enable the eee_ctrl_timer and fire the timer
in napi callback after delete the timer in .stmmac_release(), which
introduces to access eee registers in the timer function after clocks
are disabled then causes system hang. Found this issue when do
suspend/resume and reboot stress test.
It is safe to delete the timer after napi disabled and disable lpi mode.
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start phylink instance and resume back the PHY to supply
RX clock to MAC before MAC layer initialization by calling
.stmmac_hw_setup(), since DMA reset depends on the RX clock,
otherwise DMA reset cost maximum timeout value then finally
timeout.
Fixes: 74371272f9 ("net: stmmac: Convert to phylink and remove phylib logic")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current timeout value is not enough for gmac5 dma reset
on imx8mp platform, increase the timeout range.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The m250_sel mux clock uses bit 4 in the PRG_ETH0 register. Fix this by
shifting the PRG_ETH0_CLK_M250_SEL_MASK accordingly as the "mask" in
struct clk_mux expects the mask relative to the "shift" field in the
same struct.
While here, get rid of the PRG_ETH0_CLK_M250_SEL_SHIFT macro and use
__ffs() to determine it from the existing PRG_ETH0_CLK_M250_SEL_MASK
macro.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201205213207.519341-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 7579262478 ("net: stmmac: add flexible PPS to dwmac
4.10a") was intended to modify the struct dwmac410_ops, but it got
somehow badly merged and modified the struct dwmac4_ops.
Revert the modification in struct dwmac4_ops and re-apply it
properly in struct dwmac410_ops.
Fixes: 7579262478 ("net: stmmac: add flexible PPS to dwmac 4.10a")
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20201124223729.886992-1-antonio.borneo@st.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver uses a normal timer for TX coalescing, which means that the
with the default tx-usecs of 1000 microseconds the cleanups actually
happen 10 ms or more later with HZ=100. This leads to very low
througput with TCP when bridged to a slow link such as a 4G modem. Fix
this by using an hrtimer instead.
On my ARM platform with HZ=100 and the default TX coalescing settings
(tx-frames 25 tx-usecs 1000), with "tc qdisc add dev eth0 root netem
delay 60ms 40ms rate 50Mbit" run on the server, netperf's TCP_STREAM
improves from ~5.5 Mbps to ~100 Mbps.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20201120150208.6838-1-vincent.whitchurch@axis.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix an issue where dump stack is printed on suspend resume flow due to
netif_set_real_num_rx_queues() is not called with rtnl_lock held().
Fixes: 686cff3d70 ("net: stmmac: Fix incorrect location to set real_num_rx|tx_queues")
Reported-by: Christophe ROULLIER <christophe.roullier@st.com>
Tested-by: Christophe ROULLIER <christophe.roullier@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Link: https://lore.kernel.org/r/20201115074210.23605-1-vee.khee.wong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 9efc9b2b04 ("net: stmmac: Add dwmac-intel-plat for GBE driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605249243-17262-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the phy enables power saving technology, the dwmac's software reset
needs more time to complete, enlarge dma reset timeout to 200000us.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201113090902.5c7aab1a@xhacker.debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the devm_reset_control_get_optional() and devm_clk_get_optional()
rather than open coding them.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201112092606.5173aa6f@xhacker.debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The return pointer of dwc_eth_dwmac_data's .probe isn't used, and
"probe" usually return int, so change the prototype to follow standard
way. Secondly, it can simplify the tegra_eqos_probe() code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201109160440.3a736ee3@xhacker.debian
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set all EHL/TGL phy_addr to -1 so that the driver will automatically
detect it at run-time by probing all the possible 32 addresses.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Link: https://lore.kernel.org/r/20201106094341.4241-1-vee.khee.wong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch enables the HW LPI Timer which controls the automatic entry
and exit of the LPI state.
The EEE LPI timer value is configured through ethtool. The driver will
auto select the LPI HW timer if the value in the HW timer supported range.
Else, the driver will fallback to SW timer.
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Link: https://lore.kernel.org/r/20201027160051.22898-1-weifeng.voon@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit "stmmac: intel: Adding ref clock 1us tic for LPI cntr"
introduced a regression which leads to the kernel panic duing loading
of the dwmac_intel module.
Move the code block after pci resources is obtained.
Fixes: b4c5f83ae3 ("stmmac: intel: Adding ref clock 1us tic for LPI cntr")
Cc: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Link: https://lore.kernel.org/r/20201029093228.1741-1-vee.khee.wong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool manual stated that the tx-timer is the "the amount of time the
device should stay in idle mode prior to asserting its Tx LPI". The
previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
timer duration which is not correct. Hence, this patch fixes the
"ethtool --set-eee tx-timer" to configure the EEE LPI timer.
The LPI TW Timer will be using the defined default value instead of
"ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.
Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer
module param.
*EEE TW Timer will be configured with default value only, not able to be
configured through ethtool or module param. This follows the implementation
of the EEE LS Timer.
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding reference clock (1us tic) for all LPI timer on Intel platforms.
The reference clock is derived from ptp clk. This also enables all LPI
counter.
Signed-off-by: Rusaimi Amira Ruslan <rusaimi.amira.rusaimi@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While unloading the dwmac-intel driver, clk_disable_unprepare() is
being called twice in stmmac_dvr_remove() and
intel_eth_pci_remove(). This causes kernel panic on the second call.
Removing the second call of clk_disable_unprepare() in
intel_eth_pci_remove().
Fixes: 09f012e64e ("stmmac: intel: Fix clock handling on error and remove paths")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail
Queuing. This option allows packets that fail VLAN filter to be routed
to a specific Rx queue when Receive All is also set.
When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All
will pass up all rx packets that failed address filtering (similar to
promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN
filters and get routed to selected VFFQ Rx queue.
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE should be only be enabled during stmmac_mac_link_up() when the
link are up and being set up properly. set_eee should only do settings
configuration and disabling the eee.
Without this fix, turning on EEE using ethtool will return
"Operation not supported". This is due to the driver is in a dead loop
waiting for eee to be advertised in the for eee to be activated but the
driver will only configure the EEE advertisement after the eee is
activated.
Ethtool should only return "Operation not supported" if there is no EEE
capbility in the MAC controller.
Fixes: 8a7493e58a ("net: stmmac: Fix a race in EEE enable callback")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support to --show-ring & --set-ring Ethtool functions:
- Adding min, max, power of two check to new ring parameter's value.
- Bring down the network interface before changing the value of ring
parameters.
- Bring up the network interface after changing the value of ring
parameters.
Signed-off-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of stmmac_stop_all_queues() and
stmmac_start_all_queues() will not work correctly when the value of
tx_queues_to_use is changed through ethtool -L DEVNAME rx N tx M command.
Also, netif_tx_start|stop_all_queues() are only needed in driver open()
and close() only.
Fixes: c22a3f48 net: stmmac: adding multiple napi mechanism
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_set_real_num_tx_queues() & netif_set_real_num_rx_queues() should be
used to inform network stack about the real Tx & Rx queue (active) number
in both stmmac_open() and stmmac_resume(), therefore, we move the code
from stmmac_dvr_probe() to stmmac_hw_setup().
Fixes: c02b7a9145 net: stmmac: use netif_set_real_num_{rx,tx}_queues
Signed-off-by: Aashish Verma <aashishx.verma@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restructure NAPI add and delete process so that we can call them
accordingly in open() and ethtool_set_channels() accordingly.
Introduced stmmac_reinit_queues() to handle the transition needed
for changing Rx & Tx channels accordingly.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found the following warning when using W=1 to build kernel:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3634:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret, coe = priv->hw->rx_csum;
When digging stmmac_get_rx_header_len(), dwmac4_get_rx_header_len() and
dwxgmac2_get_rx_header_len() return 0 only, without any error code to
report. Therefore, it's better to define get_rx_header_len() as void.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yannick Vignon
David Wu
Seb Laveze
Samuel Holland
Noor Azura Ahmad Tarmizi
Martin Blumenstingl
Jakub Kicinski
Zheng Yongjun
Wong Vee Khee
Fugang Duan
Antonio Borneo
Vincent Whitchurch
Zhang Changzhong
Jisheng Zhang
Voon Weifeng
Tom Rix
Vineetha G. Jaya Kumaran
Marek Szyprowski
David S. Miller
Rusaimi Amira Ruslan
Chuah, Kim Tatt
Jesse Brandeburg
Song, Yoong Siang
Ong Boon Leong
Aashish Verma
Luo Jiaxing