This adds platform-specific declarations for the PSC clocks on TI
DM644x based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PSC clocks on TI
DM365 based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PSC clocks on TI
DM355 based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PSC clocks on TI DA850/
OMAP-L138/AM18XX SoCs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PSC clocks on TI DA830/
OMAP-L137/AM17XX SoCs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a new driver for mach-davinci PSC clocks. This is porting the
code from arch/arm/mach-davinci/psc.c to the common clock framework and
is converting it to use regmap to simplify the code. Additionally, it
adds device tree support for these clocks.
Note: although there are similar clocks for TI Keystone we are not able
to share the code for a few reasons. The keystone clocks are device tree
only and use legacy one-node-per-clock bindings. Also the keystone
driver makes the assumption that there is only one PSC per SoC and uses
global variables, but here we have two controllers per SoC.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI
DM646x based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI
DM644x based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI
DM365 based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI
DM355 based systems.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI DA850/
OMAP-L138/AM18XX SoCs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds platform-specific declarations for the PLL clocks on TI DA830/
OMAP-L137/AM17XX SoCs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a new driver for mach-davinci PLL clocks. This is porting the
code from arch/arm/mach-davinci/clock.c to the common clock framework.
Additionally, it adds device tree support for these clocks.
The ifeq ($(CONFIG_COMMON_CLK), y) in the Makefile is needed to prevent
compile errors until the clock code in arch/arm/mach-davinci is removed.
Note: although there are similar clocks for TI Keystone we are not able
to share the code for a few reasons. The keystone clocks are device tree
only and use legacy one-node-per-clock bindings. Also the register
layouts are a bit different, which would add even more if/else mess
to the keystone clocks. And the keystone PLL driver doesn't support
setting clock rates.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Commit aa795c41d9 ("clk: Add devm_of_clk_add_hw_provider()/del_provider()
APIs") adds devm_of_clk_add_hw_provider which takes care of deleting the
clock provider when the clock providers device is removed.
This patch makes use of devm_of_clk_add_hw_provider() instead of
of_clk_add_hw_provider() so that we can eliminate the need of explicit
scmi_clocks_remove for just doing of_clk_del_provider()
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add devm_of_platform_populate() to populate devices which are children
of the root node.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fabia PLL is a Digital Frequency Locked Loop (DFLL) clock
generator which has a wide range of frequency output. It
supports dynamic updating of the output frequency
("frequency slewing") without need to turn off the PLL
before configuration. Add support for initial configuration
and programming sequence to control fabia PLLs.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
[sboyd: Shorten code a little]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For upcoming targets like sdm845, POR value of the hardware clock control
bit is set for most of root clocks which needs to be cleared for software
to be able to control. For older targets like MSM8996, this bit is reserved
bit and having POR value as 0 so this patch will work for the older targets
too. So update the configuration mask to take care of the same to clear
hardware clock control bit.
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
XO is onchip buffer clock to generate 19.2MHz.
This patch adds support to 5 XO buffer clocks found on PMIC8921,
these buffer clocks can be controlled from external pin or in
manual mode.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to ECO design change,
1. add new clock mux data and change some
2. add new clock gate data and clock factor data
3. change status register offset of infra subsystem
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We are now allowing to register debugfs without a valid device, and not
having a valid name will end up using "dummy*" to create debugfs dir.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It's found that the clock phase output from clk_summary is
wrong compared to the actual phase reading from the register.
cat /sys/kernel/debug/clk/clk_summary | grep sdio_sample
sdio_sample 0 1 0 50000000 0 -22
It exposes an issue that clk core, clk_core_get_phase, always
returns the cached core->phase which should be either updated
by calling clk_set_phase or directly from the first place the
clk was registered.
When registering the clk, the core->phase geting from ->get_phase()
may return negative value indicating error. This is quite common
since the clk's phase may be highly related to its parent chain,
but it was temporarily orphan when registered, since its parent
chains hadn't be ready at that time, so the clk drivers decide to
return error in this case. However, if no clk_set_phase is called or
maybe the ->set_phase() isn't even implemented, the core->phase would
never be updated. This is wrong, and we should try to update it when
all its parent chains are settled down, like the way of updating clock
rate for that. But it's not deserved to complicate the code now and
just update it anyway when calling clk_core_get_phase, which would be
much simple and enough.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clearfog boards can come with a CPU clocked at 1600MHz (commercial)
or 1333MHz (industrial).
They have also some dip-switches to select a different clock (666, 800,
1066, 1200).
The funny thing is that the recovery button is on the MPP34 fq selector.
So, when booting an industrial board with this button down, the frequency
666MHz is selected (and the kernel didn't boot).
This patch add all the missing clocks.
The only mode I didn't test is 2GHz (uboot found 4294MHz instead :/ ).
Fixes: 0e85aeced4 ("clk: mvebu: add clock support for Armada 380/385")
Cc: <stable@vger.kernel.org> # 3.16.x: 9593f4f56cf5: clk: mvebu: armada-38x: add support for 1866MHz variants
Cc: <stable@vger.kernel.org> # 3.16.x
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When changing or retrieving clock parents, the caller is in a sleepable
state (like prepare) so the GPIO operation need not be atomic. Replace
gpiod_{g|s}et_value with gpiod_{g|s}et_value_cansleep in the {g|s}et_parent
calls for the GPIO based clock mux.
This fixes a "slowpath" warning when the GPIO controller is an I2C expander
or something similar.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Without COMMON_CLK_HI655X Wifi and bluetooth are non-functional on Hikey.
As suggested by Arnd, enable the driver automatically when the parent
driver is selected. With sensible defaults in place, we can leave other
choices for EXPERT.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Suggested-by: Arnd Bergmann <arnd@linaro.org>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add two configuration flags to be able to not compile all the time
stm32f and stm32h7 drivers when ARCH_STM32 is set.
That help to save some space on those small platforms.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
STM32F769 has 2 SDMMC port, add clock entry for the second one.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds DSI clock for STM32F469 board
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add missing clock data 'CLK_AUDIO_AFE_CONN' for MT7622 audsys.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clock for which all PWM devices on MT7623 or MT2701 actually depending
on has to be divided by four from its parent clock axi_sel in the clock
path prior to PWM devices.
Consequently, adding a fixed-factor clock axisel_d4 as one-fourth of
clock axi_sel allows that PWM devices can have the correct resolution
calculation.
Cc: stable@vger.kernel.org
Fixes: e986211827 ("clk: mediatek: Add MT2701 clock support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Thanks to new documentation, we have a better view of the clock tree.
There were few mistakes in the first version of this driver, the main one
being the parental link between the clocks. Actually the tree is more
flat that we though. Most of the IP blocks require two clocks: one for
the IP itself and one for accessing the registers, and unlike what we
wrote there is no link between these two clocks.
The other mistakes were about the name of the clocks: the root clock is
not the Audio PLL but the PLL0, and what we called the EIP clock is named
the x2 Core clock and is used by other IP block than the EIP ones.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CM_PLLx and A2W_XOSC_CTRL registers are accessed by different clock
handlers and must be accessed with ->regs_lock held.
Update the sections where this protection is missing.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
ana->maskX values are already '~'-ed in bcm2835_pll_set_rate(). Remove
the '~' in the definition to fix ANA setup.
Note that this commit fixes a long standing bug preventing one from
using an HDMI display if it's plugged after the FW has booted Linux.
This is because PLLH is used by the HDMI encoder to generate the pixel
clock.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Allwinner H6 SoC has a CCU which has been largely rearranged.
Add support for it in the sunxi-ng CCU framework.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
On the new Allwinner H6 SoC, multiple PLL's are NMP style clocks
(modelled as NKMP with no K) and have fixed post-dividers.
Add fixed post divider support to the NKMP style clocks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
When getting the clock related warnings, it is useful to know what
is the clock name that is causing the problem and the cause of the
problem.
Add the clock name and the the warning cause to the log, so that the
output becomes clearer like this:
[ 2.383969] ------------[ cut here ]------------
[ 2.388720] WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:814 clk_core_disable+0xd4/0xf8
[ 2.396658] uart4_ipg_gate already disabled
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The symbol is in the __initconst section but not marked init, which
caused a warning when building with LTO.
This makes it 'const' as was obviously intended.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c80dfd9bf5 ("clk: hisilicon: add CRG driver for Hi3516CV300 SoC")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When we build this driver with on x86-32, gcc produces a false-positive warning:
drivers/clk/renesas/clk-sh73a0.c: In function 'sh73a0_cpg_clocks_init':
drivers/clk/renesas/clk-sh73a0.c:155:10: error: 'parent_name' may be used uninitialized in this function [-Werror=maybe-uninitialized]
return clk_register_fixed_factor(NULL, name, parent_name, 0,
We can work around that warning by adding a fake initialization, I tried
and failed to come up with any better workaround. This is currently one
of few remaining warnings for a 4.14.y randconfig build, so it would be
good to also have it backported at least to that version. Older versions
have more randconfig warnings, so we might not care.
I had not noticed this earlier, because one patch in my randconfig test
tree removes the '-ffreestanding' option on x86-32, and that avoids
the warning. The -ffreestanding flag was originally global but moved
into arch/i386 by Andi Kleen in commit 6edfba1b33 ("[PATCH] x86_64:
Don't define string functions to builtin") as a 'temporary workaround'.
Like many temporary hacks, this turned out to be rather long-lived, from
all I can tell we still need a simple fix to asm/string_32.h before it
can be removed, but I'm not sure about how to best do that.
Cc: stable@vger.kernel.org
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a few gate clocks which are used for gating RTC for some
devices on AON area of SC9860.
This patch has been tested on SC9860, with this patch and proper DT
configurations, the watchdog can be initialized and work well.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Forward the errors returned by __clk_pllv2_set_rate() in the recalc rate
function, to avoid using uninitialized values for the rate calculation.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
aggre0 bus clks are not associated with any of the drivers, so its
important that these clks are always on to get peripherals on this
bus working. So mark them as critical.
Eventually when we have a proper bus driver these clks can be marked
appropriately.
Without this patch pcie on db820c is not functional.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk_round_rate() is intended to be used to round a given clock rate to
the closest one achievable by the actual clock. This implies that the
input to clk_round_rate() is expected to be unachievable - and such
cases shouldn't be treated as exceptional.
To reflect this, remove the WARN_ONs which trigger when an unachievable
clock rate is passed to vexpress_osc_round_rate().
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Clock framework has a provider API(clk_hw_set_rate_range) to set the
min/max rate of a clock. Use the same to set the boundaries for the
vexpress osc clock.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Running sparse on the samsung clk directory has some noise that we can
fix to look for future problems easier.
drivers/clk/samsung/clk-s3c2443.c:111:26: warning: symbol 's3c2443_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:139:26: warning: symbol 's3c2443_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:152:27: warning: symbol 's3c2443_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:186:28: warning: symbol 's3c2443_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:241:26: warning: symbol 's3c2416_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:247:26: warning: symbol 's3c2416_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:253:27: warning: symbol 's3c2416_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:263:28: warning: symbol 's3c2416_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:291:26: warning: symbol 's3c2443_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:296:27: warning: symbol 's3c2443_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:305:28: warning: symbol 's3c2443_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:321:26: warning: symbol 's3c2450_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:328:26: warning: symbol 's3c2450_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:334:27: warning: symbol 's3c2450_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:345:28: warning: symbol 's3c2450_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:368:33: warning: symbol 's3c2443_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2443.c:464:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2443.c:470:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2443.c:476:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2412.c:96:26: warning: symbol 's3c2412_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:108:35: warning: symbol 's3c2412_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:128:26: warning: symbol 's3c2412_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:146:27: warning: symbol 's3c2412_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:177:28: warning: symbol 's3c2412_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:227:33: warning: symbol 's3c2412_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2412.c:292:43: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:98:26: warning: symbol 's3c2410_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:114:26: warning: symbol 's3c2410_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:119:27: warning: symbol 's3c2410_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:138:28: warning: symbol 's3c2410_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:203:26: warning: symbol 's3c2410_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:207:35: warning: symbol 's3c2410_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:218:28: warning: symbol 's3c2410_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:272:26: warning: symbol 's3c244x_common_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:277:35: warning: symbol 's3c244x_common_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:294:26: warning: symbol 's3c244x_common_dividers' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:302:27: warning: symbol 's3c244x_common_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:306:28: warning: symbol 's3c244x_common_aliases' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:321:26: warning: symbol 's3c2440_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:325:27: warning: symbol 's3c2440_gates' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:331:35: warning: symbol 's3c2442_ffactor' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:337:26: warning: symbol 's3c2442_muxes' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:346:33: warning: symbol 's3c2410_common_frate_clks' was not declared. Should it be static?
drivers/clk/samsung/clk-s3c2410.c:471:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:477:49: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-s3c2410.c:483:49: warning: Using plain integer as NULL pointer
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to the Aspeed specification, the reset and enable sequence
should be done when the clock is stopped. The specification doesn't
define behavior if the reset is done while the clock is enabled.
From testing on the AST2500, the LPC Controller has problems if the
clock is reset while enabled.
Therefore, check whether the clock is enabled or not before performing
the reset and enable sequence in the Aspeed clock driver.
Reported-by: Lei Yu <mine260309@gmail.com>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Fixes: 15ed8ce5f8 ("clk: aspeed: Register gated clocks")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some of the Aspeed clocks are disabled by setting the relevant bit in
the "clock stop control" register to one, while others are disabled by
setting their bit to zero. The driver already uses a flag per gate to
identify this behavior, but doesn't apply it in the clock is_enabled
function.
Use the existing gate flag to correctly return whether or not a clock
is enabled in the aspeed_clk_is_enabled function.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Fixes: 6671507f0f ("clk: aspeed: Handle inverse polarity of USB port 1 clock gate")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following warnings:
drivers/clk/meson/meson8b.c:512:19: warning: symbol 'meson8b_mpeg_clk_div' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:526:19: warning: symbol 'meson8b_clk81' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:540:19: warning: symbol 'meson8b_cpu_in_sel' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:591:19: warning: symbol 'meson8b_cpu_scale_div' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:608:19: warning: symbol 'meson8b_cpu_scale_out_sel' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:626:19: warning: symbol 'meson8b_cpu_clk' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:392:27: warning: symbol 'gxbb_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:439:27: warning: symbol 'gxl_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/axg.c:195:27: warning: symbol 'axg_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/axg.c:248:27: warning: symbol 'axg_hifi_init_regs' was not declared. Should it be static?
drivers/clk/meson/meson8b.c: In function 'meson8b_clkc_probe':
drivers/clk/meson/meson8b.c:1052:14: warning: unused variable 'clk' [-Wunused-variable]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- A correction on i.MX6SX CKO clock mux options.
- A fix on i.MX7D Video PLL clock tree to include the missing dividers.
- Update i.MX6UL/ULL clock driver to add epdc_podf instead of sim_podf
clock for i.MX6ULL.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJapy5hAAoJEFBXWFqHsHzOzuIIAKtLJDt8GVHdR/NHmPVvP2I1
CL0UJVaPdef4hCbV1fKdv0gRdd28rlZsKwJLvOdiRnp826sTGfbKEJF9qX3Uolt9
33RXsly35V16fzu0UhrhbcNFsjrUHeNqG50OUMEGjYtYgM/G0qkSQryl3UENS5tt
KVuYzoR45XdCaoZaLNfSwEgYPvMh/3Qbb0hm7rMVrbmVnXAKAam+2vlTqo2rZymR
Eo+zmomTIPCnbijIguq+HQcIpuhAJNpFvad2hhyiZpk76FkHC2pTtJ4b8MTSNg+1
ogn1TTcUkibkPYt26SqexCWn/7kvuYqzEtsQ2RvoaBBAOiR0zNktWMXBc621aE0=
=KJta
-----END PGP SIGNATURE-----
Merge tag 'clk-imx-4.17-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-imx
Pull i.MX clock misc updates from Shawn Guo:
- A correction on i.MX6SX CKO clock mux options.
- A fix on i.MX7D Video PLL clock tree to include the missing dividers.
- Update i.MX6UL/ULL clock driver to add epdc_podf instead of sim_podf
clock for i.MX6ULL.
* tag 'clk-imx-4.17-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx6ull: Add epdc_podf instead of sim_podf
clk: imx: imx7d: correct video pll clock tree
clk: imx: imx6sx: update cko mux options
Sparse rightfully complains:
drivers/clk/hisilicon/clk-hisi-phase.c:88:22: warning: symbol 'clk_phase_ops' was not declared. Should it be static?
drivers/clk/hisilicon/clk-hisi-phase.c:88:22: warning: symbol 'clk_phase_ops' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
FIMC LITE SYSMMU devices are defined in exynos5250.dtsi, but clocks for
them are not instantiated by Exynos5250 clock provider driver. Add needed
definitions for those clocks to fix IOMMU probe failure:
ERROR: could not get clock /soc/sysmmu@13c40000:sysmmu(0)
exynos-sysmmu 13c40000.sysmmu: Failed to get device clock(s)!
exynos-sysmmu: probe of 13c40000.sysmmu failed with error -38
ERROR: could not get clock /soc/sysmmu@13c50000:sysmmu(0)
exynos-sysmmu 13c50000.sysmmu: Failed to get device clock(s)!
exynos-sysmmu: probe of 13c50000.sysmmu failed with error -38
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: bfed1074f2 ("clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks")
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
We need this rate to generate 100, 200, and 228.57MHz from the same
PLL. 228.57MHz is useful for a pixel clock when the VPLL is used for
an external display.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
R-Car M3-N does not have the DU2 unit but it has DU3 instead.
Fix the module clock definition to reflect that.
Fixes: 7ce36da900 ("clk: renesas: cpg-mssr: Add support for R-Car M3-N")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are many factors affecting the clock phase, including clock
rate, temperature, logic voltage and silicon process, etc. But clock
rate is the most significant one here, and the driver should be aware
of the change of the clock rate. As mmc controller need a fixed phase
after tuning was completed, at least before explicitly doing re-tune,
so this patch try to restore the clock phase by monitoring the event
of rate change.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
clk81 is a composite clock which parents all the peripheral clocks of the
platform. It is a critical clock which is used as provided by the
bootloader. We don't want to change its rate or reparent it, ever.
Remove the CLK_IGNORE_UNUSED on the mux and divider. These clock can't
gate so the flag is useless, and the gate is already critical, so the
clock won't ever be unused.
Remove CLK_SET_RATE_NO_REPARENT from mux, it is useless since the mux is
read-only.
Remove CLK_SET_RATE_PARENT from the gate and divider and use ro_ops for
the divider. A peripheral clock should not try to change the rate of
clk81. Stopping the rate propagation is good way to make sure such request
would be ignored.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fdiv fixed dividers clocks of the fixed_pll can actually gate
independently. We never had an issue so far because these clocks
were provided 'enabled' by the bootloader.
Add these gates to enable/disable the clocks when required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
mpll clocks parent can actually be divided by 1 or 2. So far, this
divider has always been set to 1, so the calculation was correct.
Now that we know it exists, model the tree correctly. If we ever get
a platform where the divider is different, we won't get into trouble
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the hifi pll to the axg clock controller. This clock maybe used as an
input of the axg audio clock controller. It uses the same settings table
as the gp0 pll but has a frac parameter allowing more precision.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Provide an option for the pll driver to round to the rate closest to the
requested rate, instead of systematically rounding down.
This may allow the provided rate to be closer to the requested rate when
rounding up is not an issue
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the frac parameter for the gp0 pll of the axg and gxl.
This allows to achieve rates between the fixed settings provided
by the table.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Finding the appropriate settings of meson plls is too tricky to be done
entirely at runtime, using calculation only. Many combination of m, n
and od won't lock which is why we are using a table for this. However,
for plls having a fractional parameters, it is possible to improve on
the result provided by the table by calculating the frac parameter.
This change adds the calculation of frac when the parameter is available
and the rate provided by the table is not an exact match for the
requested rate.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
After testing, it appears that the gxl (and axg) does not require the
special locking/reset loop which was initially added for it.
All the values present in the gxl table can locked with the simple lock
checking loop.
The change switches the gxl and axg gp0 back to the simple lock checking
loop and removes the code no longer required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Poking CNTL first may take the PLL out of reset while we are still
applying the initial settings, including the filter values
initialization. This is the case for the axg and gxl gp0 pll.
Doing this poke last ensures the pll stays in reset while the initial
settings are applied.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the missing frac parameter to the meson8b fixed_pll. It seems to be
always on this platform, so the rate remains unchanged
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On gxbb and axg, try to get the hhi regmap from the parent DT node, which
should be the HHI system controller once the necessary changes have been
made in amlogic's DTs
Until then, if getting regmap through the system controller fails, the
clock controller will fall back to the old way, requesting memory region
directly and then registering the regmap itself.
This should allow a smooth transition to syscon
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
meson8b cpu_clk has been replaced by a set of divider and mux clocks.
meson_cpu_clk is no longer used and can be removed
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Instead of migrating meson cpu_clk to clk_regmap, like the other meson
clock drivers, we take advantage of the massive rework to get rid of it
completely, and solve (the first part) of the related FIXME notice.
As pointed out in the code comments, the cpu_clk should be modeled with
dividers and muxes it is made of, instead of one big composite clock.
The cpu_clk was not working correctly to enable dvfs on meson8b. It hangs
quite often when changing the cpu clock rate. This new implementation,
based on simple elements improves the situation but the platform will
still hang from time to time. This is not acceptable so, until we can
make the mechanism around the cpu clock stable, the cpu clock subtree
has been put in read-only mode, preventing any change of the cpu clock
The notifier and read-write operation will be added back when we have a
solution to the problem.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The mpll clock is a kind of fractional divider which can gate.
When the RW operation have been added, enable/disable ops have been
mistakenly inserted in this driver. These ops are essentially a
poor copy/paste of the generic gate ops.
This change removes the gate ops from the mpll driver and inserts a
generic gate clock on each mpll divider, simplifying the mpll
driver and reducing code duplication.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson pll driver to use clk_regmap and move meson8b, gxbb and
axg's clock using meson_clk_pll to clk_regmap.
This rework is not just about clk_regmap, there a serious clean-up of
the driver code:
* Add lock and reset field: Previously inferred from the n field.
* Simplify the reset logic: Code seemed to apply reset differently but
in fact it was always the same -> assert reset, apply params,
de-assert reset. The 2 lock checking loops have been kept for now, as
they seem to be necessary.
* Do the sequence of init register pokes only at .init() instead of in
.set_rate(). Redoing the init on every set_rate() is not necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson audio divider driver to use clk_regmap and move gxbb
clock using meson_clk_audio_divider to clk_regmap.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson mpll driver to use clk_regmap and move meson8b, gxbb
and axg clocks using meson_clk_mpll to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Meson clock drivers are using struct parm to describe each field of the
clock provider. Providing helpers to access these fields with regmap
helps to keep drivers readable
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_mux to clk_regmap
Also remove a few useless tables in the process
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_divider to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_gate to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This change registers a regmap in meson8b, gxbb and axg controllers.
The clock are still accessing their registers directly through iomem.
Once all clocks handled by these controllers have been move to regmap,
the regmap register will be removed and replaced with a syscon request.
This is needed because other drivers, such as the HDMI driver, need to
access the HHI register region
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
aoclk_gate_regmap has been replaced by meson's clk_regmap.
It is no longer necessary so, remove it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Drop the gxbb ao specific regmap based clock and use the
meson clk_regmap based clock instead.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Meson clock controllers need to move the classical iomem registers to
regmap. This is triggered because the HHI controllers found on the GXBB
and GXL host more than just clocks. To properly handle this, we would
like to migrate HHI to syscon. Also GXBB AO clock controller already use
regmap, AXG AO and Audio clock controllers will as well.
The purpose of this change is to provide a common structure to these
meson controllers (and possibly others) for regmap based clocks.
This change provides the basic gate, mux and divider, based on the
helpers provided by the related generic clocks
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Over time things changes in CCF and issues have been fixed in meson
controllers.
Now, clk81 is decently modeled by read-only PLLs, a mux, a divider
and a gate. We can remove the FIXME comments related to clk81.
Also remove the comment about devm_clk_hw_register, as there is
apparently nothing wrong with it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We don't need several loop index variables in the probe function
This is far from being critical but since we are doing a vast
rework of meson clock controllers, now is the time to lower the
entropy a bit
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
There is no remove callbacks in meson's clock controllers and
of_clk_del_provider is never called if of_clk_add_hw_provider has been
executed, introducing a potential memory leak.
Fixing this by the using the devm variant.
In reality, the leak would never happen since these controllers are
never unloaded once in use ... still, this is worth cleaning.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The 'dev' pointer is directly available in gxbb and axg clock
controller, so consistently use it instead of going the through the
'pdev' pointer once in while
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This is one of the differences between 6ul and 6ull: imx6ull has no sim
but has epdc and this clock is redefined on the same bit.
This can be verified in the Reference Manuals.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In case of error, the function dev_get_regmap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 81ac38847a ("clk: qcom: Add APCS clock controller support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
platform_get_resource() may return NULL, add proper check to
avoid potential NULL dereferencing.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 4f16f7ff3b ("clk: hisilicon: Add support for Hi3660 stub clocks")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is now an helper function to round the rate when the
divider is read-only. Let's use it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When a divider clock has CLK_DIVIDER_READ_ONLY set, it means that the
register shall be left un-touched, but it does not mean the clock
should stop rate propagation if CLK_SET_RATE_PARENT is set
This is properly handled in qcom clk-regmap-divider but it was not in
the generic divider
To fix this situation, introduce a new helper function
divider_ro_round_rate, on the same model as divider_round_rate.
Fixes: e6d5e7d90b ("clk-divider: Fix READ_ONLY when divider > 1")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-By: David Lechner <david@lechnology.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some clocks may need to initialize things, whatever it is, before
being able to properly operate. Move the .init() call before any
other callback, such recalc_rate() or get_phase(), so the clock
is properly setup before being used.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add helper functions for the translation between parent index and
register value in the generic multiplexer function. The purpose of
this change is avoid duplicating the code in other clock providers,
using the same generic logic.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Export clk_div_mask() in clk-provider header so every clock providers
derived from the generic clock divider may share the definition instead
of redefining it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If we try to determine the rate of a pass-through clock (a clock which
does not implement .round_rate() nor .determine_rate()),
clk_core_round_rate_nolock() will directly forward the call to the
parent clock. In the particular case where the pass-through actually
does not have a parent, clk_core_round_rate_nolock() will directly
return 0 with the requested rate still set to the initial request
structure. This is interpreted as if the rate could be exactly achieved
while it actually cannot be adjusted.
This become a real problem when this particular pass-through clock is
the parent of a mux with the flag CLK_SET_RATE_PARENT set. The
pass-through clock will always report an exact match, get picked and
finally error when the rate is actually getting set.
This is fixed by setting the rate inside the req to 0 when core is NULL
in clk_core_round_rate_nolock() (same as in __clk_determine_rate() when
hw is NULL)
Fixes: 0f6cc2b8e9 ("clk: rework calls to round and determine rate callbacks")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fizV
-----END PGP SIGNATURE-----
Merge tag 'ti-clk-fixes-4.16' of https://github.com/t-kristo/linux-pm into clk-fixes
Pull TI SoC clock fixes for 4.16 from Tero Kristo:
* tag 'ti-clk-fixes-4.16' of https://github.com/t-kristo/linux-pm:
clk: ti: am43xx: add set-rate-parent support for display clkctrl clock
clk: ti: am33xx: add set-rate-parent support for display clkctrl clock
clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag
- Update i.MX5 clock driver to register UART4/5 clock only on i.MX50
and i.MX53. It fixes a kernel warning seen on i.MX53, caused by
commit 59dc3d8c86 ("clk: imx51: uart4, uart5 gates only exist on
imx50, imx53").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJalfiVAAoJEFBXWFqHsHzOANUIAIaKIqpJOBfr8jiYgYOgPh++
1OJrOo8f6hEboe9egGZt0j80H6LhEFoU5u4c7hiWQ9o8cYf95uYiOMyvB8KZjSMj
vYZlchtNR3uC9Vqa5vF6CcHbTV8Ug67Wqar/OFkg7CAVGvVeetyKjgyLdDP+kj6w
IjNt3WDnE/Hf7n0NFT4TeHFABS6c6dRKeQrNrULg4/OkCdNDnFzEDw3tPrNdODaD
Kbu8zP7h1G3Ankr7/cXs5/9aMKe3eVaLSfxIybQx7P2d3+RQKFbt8FIs6KFuOCpe
AYgFPKqDPkM8BYh7P9BKIeKpuDf24ZfMI5gOGPa96AJRRgUP5wrcN9E7jibjkNI=
=Magi
-----END PGP SIGNATURE-----
Merge tag 'clk-imx-fixes-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into clk-fixes
Pull i.MX clock fixes for 4.16 from Shawn Guo:
- Update i.MX5 clock driver to register UART4/5 clock only on i.MX50
and i.MX53. It fixes a kernel warning seen on i.MX53, caused by
commit 59dc3d8c86 ("clk: imx51: uart4, uart5 gates only exist on
imx50, imx53").
* tag 'clk-imx-fixes-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
clk: imx51-imx53: Fix UART4/5 registration on i.MX50 and i.MX53
A critical fix for the A31 sunxi-ng clock driver. The CLK_OUT clocks
had definitions paired with the incorrect type of clk ops. This results
in a serious oops starting with commit 946797aa3f ("clk: sunxi-ng:
Support fixed post-dividers on MP style clocks"), which exposed the
incorrect clk ops when it added a new field to the data structures,
which then nudged the underlying (compatible but incorrect) data
structures out of alignment.
-----BEGIN PGP SIGNATURE-----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=As0p
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-fixes-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clock fixes for 4.16 from Chen-Yu Tsai:
A critical fix for the A31 sunxi-ng clock driver. The CLK_OUT clocks
had definitions paired with the incorrect type of clk ops. This results
in a serious oops starting with commit 946797aa3f ("clk: sunxi-ng:
Support fixed post-dividers on MP style clocks"), which exposed the
incorrect clk ops when it added a new field to the data structures,
which then nudged the underlying (compatible but incorrect) data
structures out of alignment.
* tag 'sunxi-clk-fixes-for-4.16' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a31: Fix CLK_OUT_* clock ops
The orphan clocks reparents should migrate any existing count from the
orphan clock to its new acestor clocks, otherwise we may have
inconsistent counts in the tree and end-up with gated critical clocks
Assuming we have two clocks, A and B.
* Clock A has CLK_IS_CRITICAL flag set.
* Clock B is an ancestor of A which can gate. Clock B gate is left
enabled by the bootloader.
Step 1: Clock A is registered. Since it is a critical clock, it is
enabled. The clock being still an orphan, no parent are enabled.
Step 2: Clock B is registered and reparented to clock A (potentially
through several other clocks). We are now in situation where the enable
count of clock A is 1 while the enable count of its ancestors is 0, which
is not good.
Step 3: in lateinit, clk_disable_unused() is called, the enable_count of
clock B being 0, clock B is gated and and critical clock A actually gets
disabled.
This situation was found while adding fdiv_clk gates to the meson8b
platform. These clocks parent clk81 critical clock, which is the mother
of all peripheral clocks in this system. Because of the issue described
here, the system is crashing when clk_disable_unused() is called.
The situation is solved by reverting
commit f8f8f1d044 ("clk: Don't touch hardware when reparenting during registration").
To avoid breaking again the situation described in this commit
description, enabling critical clock should be done before walking the
orphan list. This way, a parent critical clock may not be accidentally
disabled due to the CLK_OPS_PARENT_ENABLE mechanism.
Fixes: f8f8f1d044 ("clk: Don't touch hardware when reparenting during registration")
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Turns out latest upstream U-Boot does not configure/enable pll_u which
leaves it at some default rate of 500 kHz:
root@apalis-t30:~# cat /sys/kernel/debug/clk/clk_summary | grep pll_u
pll_u 3 3 0 500000 0
Of course this won't quite work leading to the following messages:
[ 6.559593] usb 2-1: new full-speed USB device number 2 using tegra-
ehci
[ 11.759173] usb 2-1: device descriptor read/64, error -110
[ 27.119453] usb 2-1: device descriptor read/64, error -110
[ 27.389217] usb 2-1: new full-speed USB device number 3 using tegra-
ehci
[ 32.559454] usb 2-1: device descriptor read/64, error -110
[ 47.929777] usb 2-1: device descriptor read/64, error -110
[ 48.049658] usb usb2-port1: attempt power cycle
[ 48.759475] usb 2-1: new full-speed USB device number 4 using tegra-
ehci
[ 59.349457] usb 2-1: device not accepting address 4, error -110
[ 59.509449] usb 2-1: new full-speed USB device number 5 using tegra-
ehci
[ 70.069457] usb 2-1: device not accepting address 5, error -110
[ 70.079721] usb usb2-port1: unable to enumerate USB device
Fix this by actually allowing the rate also being set from within
the Linux kernel.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently VDE clock rate is determined by clock config left from
bootloader, let's not rely on it and explicitly specify the clock
rate in the CCF driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLL_C_OUT_1 can't produce 216 MHz defined in the init_table. Let's
set it to 240 MHz and explicitly specify HCLK rate for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Machine dies if HCLK, SCLK or EMC is disabled. Hence mark these clocks
as critical.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: <stable@vger.kernel.org> # v4.16
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding these EPLL output frequency entries allows to support all required
audio sample rates on the CODEC and the HDMI interface on Peach-Pit
Chromebook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This allows changing the EPLL output frequency through the audio subsystem
clock tree leaf clocks. This change is needed to support audio on the HDMI
interface on Peach-Pi(t) Chromebook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
It's found that the final phase set by driver doesn't match that of
the output from clk_summary:
dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 346
mmc0: new ultra high speed SDR104 SDIO card at address 0001
cat /sys/kernel/debug/clk/clk_summary | grep sdio_sample
sdio_sample 0 1 0 50000000 0 0
It seems the cached core->phase isn't updated after the clk was
registered. So fix this issue by updating the core->phase if setting
phase successfully.
Fixes: 9e4d04adeb ("clk: add clk_core_set_phase_nolock function")
Cc: Stable <stable@vger.kernel.org>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
RCC manages clock for debug and trace.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Two micro-controller clock output (MCO) pins are available:
MCO1 and MCO2.
For each output, it is possible to select a clock source.
The selected clock can be divided thanks to configurable
prescaler.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Each peripheral requires a bus interface clock.
Some peripherals need also a dedicated clock for their communication
interface, this clock is generally asynchronous with respect to the bus
interface clock (peripheral clock), and is named kernel clock.
For each IP, Peripheral clock and Kernel are generally gating with same
gate. Also, Kernel clocks can share a same multiplexer.
This patch introduces a mechanism to manage a gate with several
clocks and to manage a shared multiplexer (mgate and mmux).
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch adds Kernel timers.
This patch adds timers kernel clock.
Timers are gather into two groups corresponding to the APB bus
they are attached to.
Each group has its own prescaler, managed in this patch.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The RCC handles three sub-system clocks: ck_mpuss, ck_axiss
and ck_mcuss.
This patch adds also some MUX system and several prescalers.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Each PLL has 3 outputs with post-dividers.
pll1_p is dedicated for Cortex-A7
pll1_q is not connected
pll1_r is not connected
pll2_p is dedicated for AXI
pll2_q is dedicated for GPU
pll2_r is dedicated for DDR
pll3_p is dedicated for mcu
pll3_q is for Peripheral Kernel Clock
pll3_r is for Peripheral Kernel Clock
pll4_p is for Peripheral Kernel Clock
pll4_q is for Peripheral Kernel Clock
pll4_r is for Peripheral Kernel Clock
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
STMP32MP1 has 4 PLLs.
PLL supports integer and fractional mode.
Each PLL has 3 output dividers (p, q, r)
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch adds source clocks for PLLs
This patch also introduces MUX clock API.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
MP1 Gate is a gate with a set and a clear register.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch introduces the mechanism to probe stm32mp1 driver.
It also defines registers definition.
This patch also introduces the generic mechanism to register
a clock (a simple gate, divider and fixed factor).
All clocks will be defined in one table.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Tegra210 has a hw bug which can cause IP blocks to lock up when ungating a
domain. The reason is that the logic responsible for resetting the memory
built-in self test mode can come up in an undefined state because its
clock is gated by a second level clock gate (SLCG). Work around this by
making sure the logic will get some clock edges by ensuring the relevant
clock is enabled and temporarily override the relevant SLCGs.
Unfortunately for some IP blocks, the control bits for overriding the
SLCGs are not in CAR, but in the IP block itself. This means we need to
map a few extra register banks in the clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
fixup mbist
To ensure writes to clock registers have properly propagated through the
clock control logic and state machines, we need to ensure the writes have
been posted in the registers and wait for 1us after that.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is needed by the memory built-in self test work around.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Display driver assumes it can use clk_set_rate for the display clock
via set-rate-parent mechanism, so add the flag for this to id.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Certain clkctrl clocks, notably the display ones, use the
CLK_SET_RATE_PARENT feature extensively. Add support for this flag
to the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Display driver assumes it can use clk_set_rate for the display clock
via set-rate-parent mechanism, so add the flag for this to it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Currently, the driver contains a large hints table for clocks that exist
on a device, however, it is possible to probe the clocks from the firmware
also. Add support for this, and drop the clock hints table support from
the driver completely. This causes the driver to send a few extra sci-clk
messages during boot, basically one extra for each device that exists on
the SoC; on K2G this is approx 80.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Latching the clock settings is needed with certain clocks, where
the setting is "cached" in HW before doing the actual re-programming
of the clock source. This patch adds support for clock latching to
the mux clock.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Latching the clock settings is needed with certain clocks, where
the setting is "cached" in HW before doing the actual re-programming
of the clock source. This patch adds support for clock latching to
the divider clock.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Certain clocks require latching to be done, so that the actual
settings get updated on the HW that generates the clock signal.
One example of such a clock is the dra76x GMAC DPLL H14 output,
which requires its divider settings to be latched when updated.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Useful for changing few bits on a register, this makes sure for example
that the operation is done atomically in case of syscon.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Clocks related to DISP1 block require special handling for power domain
turn on/off sequences. Till now this was handled by Exynos power domain
driver, but that approach was limited only to some special cases. This
patch moves handling of those operations to clock controller driver.
This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5250 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Clocks related to DISP, GSC and MFC blocks require special handling for
power domain turn on/off sequences. Till now this was handled by Exynos
power domain driver, but that approach was limited only to some special
cases. This patch moves handling of those operations to clock controller
driver. This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5420 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Exynos5250/5420/5800 have only one clock controller, but some of their
clock depends on respective power domains. Handling integration of clock
controller and power domain can be done using runtime PM feature of CCF
framework. This however needs a separate struct device for each power
domain. This patch adds such separate driver for a group of such clocks,
which can be instantiated more than once, each time for a different
power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The MMC sample and drv clock for rockchip platforms are derived from
the bus clock output to the MMC/SDIO card. So it should never happens
that the clk rate is zero given it should inherits the clock rate from
its parent. If something goes wrong and makes the clock rate to be zero,
the calculation would be wrong but may still make the mmc tuning process
work luckily. However it makes people harder to debug when the following
data transfer is unstable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rockchip_clk_register_branch() and rockchip_clk_register_frac_branch()
should free the memory internally when seeing any failure.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
CLK_PLL_VIDEO needs to be referenced in HDMI DT entry as a possible
PHY clock parent.
Export it so it can be used later in DT.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some units have to be able to set it's own clock precisely to work
correctly. Allow them to do so by adding CLK_SET_RATE_PARENT flag.
Add this flag to DE, TCON and HDMI clocks.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Although user manuals for H3 and H5 SoCs state that minimal rate
supported by video PLL is around 30 MHz, it seems that in reality
minimal rate is around 192 MHz.
Experiments showed that any rate below 96 MHz doesn't produce any video
output at all. Even at this frequency, stable output depends on right
factors. For example, when N = 4 and M = 1, output is stable and when N
= 8 and M = 2, it's not.
BSP clock driver suggest that minimum stable frequency is 192 MHz. That
would also be in line with A64 SoC, which has similar periphery.
Set minimal video PLL rate for H3/H5 to 192 MHz.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some NM PLLs doesn't work well when their output clock rate is set below
certain rate.
Add support for that constrain.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is a test divider and post divider in video PLL,
test divider is placed before post divider, all clocks
that can select parent from video PLL should be from
post divider, NOT from pll_video_main, below are
clock tree dump before and after this patch:
Before:
pll_video_main
pll_video_main_bypass
pll_video_main_clk
lcdif_pixel_src
lcdif_pixel_cg
lcdif_pixel_pre_div
lcdif_pixel_post_div
lcdif_pixel_root_clk
After:
pll_video_main
pll_video_main_bypass
pll_video_main_clk
pll_video_test_div
pll_video_post_div
lcdif_pixel_src
lcdif_pixel_cg
lcdif_pixel_pre_div
lcdif_pixel_post_div
lcdif_pixel_root_clk
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control. System Control and Management Interface(SCMI) Message Protocol
is defined for the communication between the Application Cores(AP)
and the SCP.
This patch adds support for the clocks provided by SCP using SCMI
protocol.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
According to the i.MX7D Reference Manual, the Keypad Port module
(KPP) requires this clock gate to be enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock COMBPHY1 has already been supported by hi3798cv200 driver,
but COMBPHY0 is missing. It adds COMBPHY0 clock support.
Since the mux table is being shared by COMBPHY0 and COMBPHY1, it renames
comphy1_mux_p and comphy1_mux_table a bit to drop instance number '1'
from there.
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's a coding-style fix, which corrects the indentation for all those
clock definitions, so that the code looks nicer and new definitions can
be added with a recommended indentation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The clock HISTB_USB2_OTG_UTMI_CLK is defined by device tree bindings in
include/dt-bindings/clock/histb-clock.h, but hasn't been supported by
hi3798cv200 clock driver. Let's add the support for it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The IR clock is sourced from '24m' rather than '100m'. Correct it.
Signed-off-by: Younian Wang <wangyounian@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The unregister call sequence in error path of function
hi3798cv200_clk_register() should be opposite to the order of register
calls. Let's reverse the call sequence to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Initial support for R-Car M3-N (r8a77965), including core and module
clocks.
Based on Table 8.2d of "R-Car Series, 3rd Generation User's Manual:
Hardware (Rev. 0.80, Oct 31, 2017)".
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. To avoid possible mistakes we can use compile
time validation.
The patch introduces such validators and expands all initializers
with additional input frequency parameter, required to validate rates.
Since S3C24xx PLLs requires different validators two new macros have
been introduced to deal with it. Also, since PLLs 4502 and 4508 have
different formulas PLL_45XX_RATE has been replaced with PLL_4508_RATE.
As the patch adds only compile time validators it should not have impact
on compiled code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
In this patch an erroneous P value for 74176002 output frequency is also
corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
According to the i.MX7D Reference Manual,
SNVS block has a clock gate, accessing SNVS block
would need this clock gate to be enabled, add it
into clock tree so that SNVS module driver can
operate this clock gate.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add R-Car V3H (R8A77980) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 code.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add "rwdt" clock to r8a7792_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Add "rwdt" clock to r8a7794_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add "rwdt" clock to r8a7791_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add "rwdt" clock to r8a7790_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add "rwdt" clock to r8a7745_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add "rwdt" clock to r8a7743_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When support for the A31/A31s CCU was first added, the clock ops for
the CLK_OUT_* clocks was set to the wrong type. The clocks are MP-type,
but the ops was set for div (M) clocks. This went unnoticed until now.
This was because while they are different clocks, their data structures
aligned in a way that ccu_div_ops would access the second ccu_div_internal
and ccu_mux_internal structures, which were valid, if not incorrect.
Furthermore, the use of these CLK_OUT_* was for feeding a precise 32.768
kHz clock signal to the WiFi chip. This was achievable by using the parent
with the same clock rate and no divider. So the incorrect divider setting
did not affect this usage.
Commit 946797aa3f ("clk: sunxi-ng: Support fixed post-dividers on MP
style clocks") added a new field to the ccu_mp structure, which broke
the aforementioned alignment. Now the system crashes as div_ops tries
to look up a nonexistent table.
Reported-by: Philipp Rossak <embed3d@gmail.com>
Tested-by: Philipp Rossak <embed3d@gmail.com>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
When parent rate is 24MHz and multiplier N >= 180, intermediate clock
rate doesn't fit in 32 bit variable anymore.
Because of that, introduce function for calculating clock rate which
uses 64 bit variable for intermediate result.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently, if one of the factors isn't present, bit 0 gets always set to
1. For example, A83T has NMP PLLs modelled as NKMP PLL without K. Since
K is not specified, it's offset, width and shift is 0. Driver assumes
that lowest value possible is 1, otherwise we would get division by 0.
That situation causes that bit 0 is always set, which may change wanted
clock rate.
Fix that by masking every factor according to it's specified width.
Factors with width set to 0 won't have any influence to final register
value.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add one more entry to the exynos5433_aud_pll_rates table, this allows
to support audio sample rates: 48000, 96000, 192000 Hz with minimum
error. The M, P, S, K values re confirmed by the HW team.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
The sclk_ioclk_i2s1_bclk clock is not currently handled by any driver
and disabling this clock by the clk core prevents proper operation
of the I2S1 block. CLK_IGNORE_UNUSED flag is added as a temporary fix.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
There is a error message within devm_ioremap_resource already,
so remove the dev_err call to avoid redundant error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
There is a error message within devm_ioremap_resource already,
so remove the dev_err call to avoid redundant error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch just removes the unneeded enumeration for PLL index.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The following symbols:
SUNXI_CCU_DIV
SUNXI_CCU_MULT
SUNXI_CCU_NK
SUNXI_CCU_NKM
SUNXI_CCU_NM
SUNXI_CCU_MP
SUNXI_CCU_PHASE
were removed with the commit 06e226c7fb ("clk: sunxi-ng: Move all clock types to a library")
So selecting them is useless.
Fixes: c84f5683f6 ("clk: sunxi-ng: Add sun4i/sun7i CCU driver")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds Z clock for R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds Z clock for R8A7795 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds Z clock divider support for R-Car Gen3 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since v4.15-rc1, the DTS files for all R-Car Gen2 SoCs have been
converted to the new CPG/MSSR bindings. Hence it is now safe to no
longer enable legacy DT clock support by default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
dclk_lcdc can be sourced from a general pll source as well
as the hdmiphy's pll output. We will want to set this source
by hand (to the system-pll-source in most cases) and also
want rate changes to this clock to be able to also touch
the pll source clock if needed, so add CLK_SET_RATE_PARENT
and CLK_SET_RATE_NO_REPARENT for dclk_lcdc.
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
[ammended commit message]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
NIU clocks are supplying the interconnect connections to specific
peripherals and are currently not controlled in any way.
So to prevent things falling apart at strange moments, mark all
niu clocks as critical.
Most of them where marked as CLK_IGNORE_UNUSED, but that doesn't
help if a parent clock then gets disabled.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The clock wrongly was called hclk_vio and exported, while it actually is
a clock of the interconnect-vio connection and should therefore be always
on till we actually model the interconnect.
So fix that and don't export it as HCLK_VIO.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On axg, the rate of the mpll is stuck as if sdm value was 4 and could not
change (expect for mpll2 strangely). Looking at the vendor kernel, it
turns out a new magic bit from the undocumented HHI_PLL_TOP_MISC register
is required.
Setting this bit solves the problem and the mpll rates are back to normal
Fixes: 78b4af312f ("clk: meson-axg: add clock controller drivers")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
According to the datasheet, the od shift of sys_pll is actually 16.
Fixes: 78b4af312f ('clk: meson-axg: add clock controller drivers')
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[fixed commit message]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The fixed_pll also has a fractional part. On axg s400 board, without
this parameter, the calculated rate is off by ~8Mhz (0,4%). The fixed_pll
being the root of the peripheral clock tree, this error is propagated to
the rest of the clocks
Adding the definition of the parameter fixes the problem
Fixes: 78b4af312f ("clk: meson-axg: add clock controller drivers")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The fixed_pll of gxbb and gxl also has a fractional parameter. This has
not been a problem so far because the fractional part is actually set
to 0 on these platforms, so the rate remains correct when it is ignored.
Still, it is better represent the pll the way it is, so add the frac
parameter now
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The rate of the parent should not be multiplied by 2 when the pll has a
fractional part. This is making the rate calculation of the gxl_hdmi_pll
wrong (and others as well). This multiplication is specific
to the hdmi_pll of gxbb and is most likely due to a multiplier sitting
in front of this particular pll.
Add a fixed factor clock in front on the gxbb pll and remove this constant
from the calculation to fix the problem
Fixes: 4a47295144 ("clk: meson: fractional pll support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The hdmi pll used in the gxl family is actually different from the gxbb
one. The register layout is completely different, which explain why the
hdmi pll rate has always been rubbish on the gxl family.
Adding the correct register field is the first part of the fix to get a
correct rate out the hdmi pll
Fixes: 0d48fc558d ("clk: meson-gxbb: Add GXL/GXM GP0 Variant")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Some meson plls, such as the hdmi pll, are using a 3rd od parameter,
which is yet another "power of 2" post divider. Add it to fix the
calculation of the hdmi_pll rate
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Use the fractional part width in the calculation instead of 12, which
happens to be the witdh right now. This is safer in case the field width
ever change in the future
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The pll driver performs the rate calculation in Mhz, which adds an
unnecessary rounding down to the Mhz of the rate. Use 64bits long
integers to perform this calculation safely on meson8b and perform the
calculation in Hz instead
Fixes: 7a29a86943 ("clk: meson: Add support for Meson clock controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Read-only plls don't need param table to recalculate the rate.
Providing them with a param table is just a waste of memory.
Remove the useless tables from sys_pll on gxbb and axg.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Make sure the rate param table is available before using it.
Some read-only plls don't provide it, which is ok since the
table is not used by read-only clocks. R/W clocks are supposed
to provide it, but it does not hurt check it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
These are the main MIPS changes for 4.16. Rough overview:
- Basic support for the Ingenic JZ4770 based GCW Zero open-source
handheld video game console
- Support for the Ranchu board (used by Android emulator)
- Various cleanups and misc improvements
Fixes:
- Fix generic platform's USB_*HCI_BIG_ENDIAN selects (4.9)
- Fix vmlinuz default build when ZBOOT selected
- Fix clean up of vmlinuz targets
- Fix command line duplication (in preparation for Ingenic JZ4770)
Miscellaneous:
- Allow Processor ID reads to be to be optimised away by the compiler
(improves performance when running in guest)
- Push ARCH_MIGHT_HAVE_PC_SERIO/PARPORT down to platform level to
disable on generic platform with Ranchu board support
- Add helpers for assembler macro instructions for older assemblers
- Use assembler macro instructions to support VZ, XPA & MSA operations
on older assemblers, removing C wrapper duplication
- Various improvements to VZ & XPA assembly wrappers
- Add drivers/platform/mips/ to MIPS MAINTAINERS entry
Minor cleanups:
- Misc FPU emulation cleanups (removal of unnecessary include, moving
macros to common header, checkpatch and sparse fixes)
- Remove duplicate assignment of core in play_dead()
- Remove duplication in watchpoint handling
- Remove mips_dma_mapping_error() stub
- Use NULL instead of 0 in prepare_ftrace_return()
- Use proper kernel-doc Return keyword for
__compute_return_epc_for_insn()
- Remove duplicate semicolon in csum_fold()
Platform support:
Broadcom:
- Enable ZBOOT on BCM47xx
Generic platform:
- Add Ranchu board support, used by Android emulator
- Fix machine compatible string matching for Ranchu
- Support GIC in EIC mode
Ingenic platforms:
- Add DT, defconfig and other support for JZ4770 SoC and GCW Zero
- Support dynamnic machine types (i.e. JZ4740 / JZ4770 / JZ4780)
- Add Ingenic JZ4770 CGU clocks
- General Ingenic clk changes to prepare for JZ4770 SoC support
- Use common command line handling code
- Add DT vendor prefix to GCW (Game Consoles Worldwide)
Loongson:
- Add MAINTAINERS entry for Loongson2 and Loongson3 platforms
- Drop 32-bit support for Loongson 2E/2F devices
- Fix build failures due to multiple use of "MEM_RESERVED"
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEd80NauSabkiESfLYbAtpk944dnoFAlp64ZUACgkQbAtpk944
dnrXrg//UPWeZMye/uHw0eEeJJjybyA0IWpJ6M94gbHxpduhQsjYU3CR9U4ZBmhs
feY53dahh0RCR0k28EF8DEPkoUbGFKmyYCnvqAuatq1XOjAZtlgS9+VVzbK+Iswm
XkZD1MBoZ49o0meyjQrH/2Ri/t6tHuzo0G2WtRJ8FnVruN9ymG6D5pR4Y31gDucb
6JkTXjNfRJIKd0qJgP+c3HdlKE7jlnCTJnzHdA+5FbZVwKbm2/6KxbQo5Gc1BXJX
4j7I4nJ0FIz0cB6fHbcccFSW9w3lPa9bQ4XpYPJYE6a36QldFvMWHRxvI6rxrACN
5mPqIB9uqvtW8sdUbJtNRXFlNnm8XZzvsNqP6WxGQPW70+q2camni9W/gC1ifQsF
+uVV54yj3Ky8xQNbbpfbDp/tFXRuLtj3DV4/a3dwA5J0YGEuMn1zzV5WTTzymFVn
3NKl62LDUlzBNw0d1lUPMY6P1oKcNnRhLxBq0cxaB7AdOLF0jlCQ/wYUhXPpblj6
CQB4cupR4IMvL7FZ1RS98e1RHaF8mXpaZBnGXT251DxZEre9OXCJxDdzqemedTVi
SaCcvQqApCQD8OihL+wHZLew8Vp4EvwGAa++Evu/Ot4rWjY/9MGLtewYk8jkOEf6
qk30dDn86ou29HNwpzfWadIq5Zew+QftifGOzTcuzgrJXXt+jH8=
=7iwT
-----END PGP SIGNATURE-----
Merge tag 'mips_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.16.
Rough overview:
(1) Basic support for the Ingenic JZ4770 based GCW Zero open-source
handheld video game console
(2) Support for the Ranchu board (used by Android emulator)
(3) Various cleanups and misc improvements
More detailed summary:
Fixes:
- Fix generic platform's USB_*HCI_BIG_ENDIAN selects (4.9)
- Fix vmlinuz default build when ZBOOT selected
- Fix clean up of vmlinuz targets
- Fix command line duplication (in preparation for Ingenic JZ4770)
Miscellaneous:
- Allow Processor ID reads to be to be optimised away by the compiler
(improves performance when running in guest)
- Push ARCH_MIGHT_HAVE_PC_SERIO/PARPORT down to platform level to
disable on generic platform with Ranchu board support
- Add helpers for assembler macro instructions for older assemblers
- Use assembler macro instructions to support VZ, XPA & MSA
operations on older assemblers, removing C wrapper duplication
- Various improvements to VZ & XPA assembly wrappers
- Add drivers/platform/mips/ to MIPS MAINTAINERS entry
Minor cleanups:
- Misc FPU emulation cleanups (removal of unnecessary include, moving
macros to common header, checkpatch and sparse fixes)
- Remove duplicate assignment of core in play_dead()
- Remove duplication in watchpoint handling
- Remove mips_dma_mapping_error() stub
- Use NULL instead of 0 in prepare_ftrace_return()
- Use proper kernel-doc Return keyword for
__compute_return_epc_for_insn()
- Remove duplicate semicolon in csum_fold()
Platform support:
Broadcom:
- Enable ZBOOT on BCM47xx
Generic platform:
- Add Ranchu board support, used by Android emulator
- Fix machine compatible string matching for Ranchu
- Support GIC in EIC mode
Ingenic platforms:
- Add DT, defconfig and other support for JZ4770 SoC and GCW Zero
- Support dynamnic machine types (i.e. JZ4740 / JZ4770 / JZ4780)
- Add Ingenic JZ4770 CGU clocks
- General Ingenic clk changes to prepare for JZ4770 SoC support
- Use common command line handling code
- Add DT vendor prefix to GCW (Game Consoles Worldwide)
Loongson:
- Add MAINTAINERS entry for Loongson2 and Loongson3 platforms
- Drop 32-bit support for Loongson 2E/2F devices
- Fix build failures due to multiple use of 'MEM_RESERVED'"
* tag 'mips_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (53 commits)
MIPS: Malta: Sanitize mouse and keyboard configuration.
MIPS: Update defconfigs after previous patch.
MIPS: Push ARCH_MIGHT_HAVE_PC_SERIO down to platform level
MIPS: Push ARCH_MIGHT_HAVE_PC_PARPORT down to platform level
MIPS: SMP-CPS: Remove duplicate assignment of core in play_dead
MIPS: Generic: Support GIC in EIC mode
MIPS: generic: Fix Makefile alignment
MIPS: generic: Fix ranchu_of_match[] termination
MIPS: generic: Fix machine compatible matching
MIPS: Loongson fix name confict - MEM_RESERVED
MIPS: bcm47xx: enable ZBOOT support
MIPS: Fix trailing semicolon
MIPS: Watch: Avoid duplication of bits in mips_read_watch_registers
MIPS: Watch: Avoid duplication of bits in mips_install_watch_registers.
MIPS: MSA: Update helpers to use new asm macros
MIPS: XPA: Standardise readx/writex accessors
MIPS: XPA: Allow use of $0 (zero) to MTHC0
MIPS: XPA: Use XPA instructions in assembly
MIPS: VZ: Pass GC0 register names in $n format
MIPS: VZ: Update helpers to use new asm macros
...
to the clk rate protection support added by Jerome Brunet. This feature
will allow consumers to lock in a certain rate on the output of a clk so
that things like audio playback don't hear pops when the clk frequency
changes due to shared parent clks changing rates. Currently the clk
API doesn't guarantee the rate of a clk stays at the rate you request
after clk_set_rate() is called, so this new API will allow drivers
to express that requirement. Beyond this, the core got some debugfs
pretty printing patches and a couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h file
causes small one-liners in all the architecture Kbuild files. Overall, the
driver diff seems to be the normal stuff that comes all the time to
fix little problems here and there and to support new hardware.
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=bGPp
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework has a handful of patches this time around, mostly
due to the clk rate protection support added by Jerome Brunet.
This feature will allow consumers to lock in a certain rate on the
output of a clk so that things like audio playback don't hear pops
when the clk frequency changes due to shared parent clks changing
rates. Currently the clk API doesn't guarantee the rate of a clk stays
at the rate you request after clk_set_rate() is called, so this new
API will allow drivers to express that requirement.
Beyond this, the core got some debugfs pretty printing patches and a
couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h
file causes small one-liners in all the architecture Kbuild files.
Overall, the driver diff seems to be the normal stuff that comes all
the time to fix little problems here and there and to support new
hardware.
Summary:
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (125 commits)
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: fix reentrancy of clk_enable() on UP systems
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: renesas: r8a7796: Add FDP clock
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
clk: Improve flags doc for of_clk_detect_critical()
arch: Remove clkdev.h asm-generic from Kbuild
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: Prepare to remove asm-generic/clkdev.h
...
We get a moderate number of new machines this time, and only one
new SoC variant (Actions S700):
Actions:
S700 Soc and CubieBoard7 development board
Allo.com Sparky Single-board-computer
Allwinner:
Orange Pi R1 development board
Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
Axentia Nattis/Natte digital signage
sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
SolidRun Humminboard2 development board
Variscite DART-MX6 SoM and Carrier-board
Technologic TS-4600 and TS-7970 development board
Toradex Colibri iMX7D SoM board
v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
Moxa UC-8410A Series industrial computer
Gemini:
D-Link DNS-313 NAS enclosure
OMAP:
LogicPD OMAP35xx SOM-LV devkit
LogicPD OMAP35xx Torpedo devkit
Renesas:
r8a77970 (V3M) Starter Kit board
r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
Aspeed clk controller support
Freescale LS1088A, LS1021A device support
Gemini Ethernet, PCI, TVE, panel
Keystone gpio, qspi, more uarts
Mediatek cpufreq, regulator, clock, reset
Marvell thermal, cpufreq, nand
Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
Rockchip Mipi, GPU, display
Samsung Exynos5433 PMU, power domain, nfc
Spreadtrum: sc9860 clocks
Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qN1F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
* clk-aspeed:
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
dt-bindings: clock: Add ASPEED constants
* clk-lock-UP:
clk: fix reentrancy of clk_enable() on UP systems
* clk-mediatek:
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: mediatek: Fix all warnings for missing struct clk_onecell_data
clk: mediatek: fixup test-building of MediaTek clock drivers
clk: mediatek: group drivers under indpendent menu
* clk-allwinner:
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: sunxi-ng: fix the A64/H5 clock description of DE2 CCU
clk: sunxi-ng: add support for Allwinner H3 DE2 CCU
dt-bindings: fix the binding of Allwinner DE2 CCU of A83T and H3
clk: sunxi-ng: sun8i: a83t: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: sun8i: a83t: Add /2 fixed post divider to audio PLL
clk: sunxi-ng: Support fixed post-dividers on NM style clocks
clk: sunxi-ng: sun50i: a64: Add 2x fixed post-divider to MMC module clocks
clk: sunxi-ng: Support fixed post-dividers on MP style clocks
clk: sunxi: Use PTR_ERR_OR_ZERO()
* clk-remove-asm-clkdev:
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
arch: Remove clkdev.h asm-generic from Kbuild
clk: Prepare to remove asm-generic/clkdev.h
blackfin: Use generic clkdev.h header
* clk-debugfs-fixes:
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: Improve flags doc for of_clk_detect_critical()
* clk-renesas:
clk: renesas: r8a7796: Add FDP clock
clk: renesas: cpg-mssr: Keep wakeup sources active during system suspend
clk: renesas: mstp: Keep wakeup sources active during system suspend
clk: renesas: r8a77970: Add LVDS clock
* clk-meson:
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: meson-axg: make local symbol axg_gp0_params_table static
clk: meson-axg: fix return value check in axg_clkc_probe()
clk: meson: mpll: use 64-bit maths in params_from_rate
clk: meson-axg: add clock controller drivers
clk: meson-axg: add clocks dt-bindings required header
dt-bindings: clock: add compatible variant for the Meson-AXG
clk: meson: make the spinlock naming more specific
clk: meson: gxbb: remove IGNORE_UNUSED from mmc clocks
clk: meson: gxbb: fix wrong clock for SARADC/SANA
* clk-iproc:
clk: iproc: Minor tidy up of iproc pll data structures
clk: iproc: Allow plls to do minor rate changes without reset
clk: iproc: Fix error in the pll post divider rate calculation
clk: iproc: Allow iproc pll to runtime calculate vco parameters
* clk-mvebu:
clk: mvebu: armada-37xx-periph: Use PTR_ERR_OR_ZERO()
* clk-qcom-a53:
clk: qcom: Add APCS clock controller support
clk: qcom: Add regmap mux-div clocks support
clk: qcom: Add A53 PLL support
* clk-at91:
clk: at91: pmc: Support backup for programmable clocks
clk: at91: pmc: Save SCSR during suspend
clk: at91: pmc: Wait for clocks when resuming
* clk-imx7ulp:
clk: Don't touch hardware when reparenting during registration
* clk-axigen:
clk: axi-clkgen: Round closest in round_rate() and recalc_rate()
clk: axi-clkgen: Correctly handle nocount bit in recalc_rate()
* clk-si5351:
clk: si5351: _si5351_clkout_reset_pll() can be static
clk: si5351: Do not enable parent clocks on probe
clk: si5351: Rename internal plls to avoid name collisions
clk: si5351: Apply PLL soft reset before enabling the outputs
clk: si5351: Add DT property to enable PLL reset
clk: si5351: implement remove handler
* clk-pxa:
clk: pxa: unbreak lookup of CLK_POUT
* clk-qcom-alpha-pll:
clk: qcom: add read-only alpha pll post divider operations
clk: qcom: support for 2 bit PLL post divider
clk: qcom: support Brammo type Alpha PLL
clk: qcom: support Huayra type Alpha PLL
clk: qcom: support for dynamic updating the PLL
clk: qcom: support for alpha mode configuration
clk: qcom: flag for 64 bit CONFIG_CTL
clk: qcom: fix 16 bit alpha support calculation
clk: qcom: support for alpha pll properties
* clk-check-ops-ptr:
clk: check ops pointer on clock register
* clk-protect-rate:
clk: fix set_rate_range when current rate is out of range
clk: add clk_rate_exclusive api
clk: cosmetic changes to clk_summary debugfs entry
clk: add clock protection mechanism to clk core
clk: use round rate to bail out early in set_rate
clk: rework calls to round and determine rate callbacks
clk: add clk_core_set_phase_nolock function
clk: take the prepare lock out of clk_core_set_parent
clk: fix incorrect usage of ENOSYS
* clk-omap:
clk: ti: Drop legacy clk-3xxx-legacy code
The USB port 1 clock gate control has an inversed polarity
from all the other clock gates in the chip. This makes the
aspeed_clk_{enable,disable} functions honor the flag
CLK_GATE_SET_TO_DISABLE and set that flag appropriately
so it's set for all clocks except USB port 1.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In case of error, the function of_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: a2e230c7b2ea ("clk: Add clock driver for ASPEED BMC SoCs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There are some resets that are not associated with gates. These are
represented by a reset controller.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The majority of the clocks in the system are gates paired with a reset
controller that holds the IP in reset.
This borrows from clk_hw_register_gate, but registers two 'gates', one
to control the clock enable register and the other to control the reset
IP. This allows us to enforce the ordering:
1. Place IP in reset
2. Enable clock
3. Delay
4. Release reset
There are some gates that do not have an associated reset; these are
handled by using -1 as the index for the reset.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This registers a platform driver to set up all of the non-core clocks.
The clocks that have configurable rates are now registered.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This registers the core clocks; those which are required to calculate
the rate of the timer peripheral so the system can load a clocksource
driver.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds the stub of a driver for the ASPEED SoCs. The clocks are
defined and the static registration is set up.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the clocks provided by the CGU in the Ingenic JZ4770
SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18482/
Signed-off-by: James Hogan <jhogan@kernel.org>
This commit permits the PLLs to be dynamically enabled and disabled when
their children clocks are enabled and disabled.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18480/
Signed-off-by: James Hogan <jhogan@kernel.org>
The second PLL of the JZ4770 does not have a bypass bit.
This commit makes it possible to support it with the current common CGU
code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18479/
Signed-off-by: James Hogan <jhogan@kernel.org>
Previously, the clocks with a fixed divider would report their rate
as being the same as the one of their parent, independently of the
divider in use. This commit fixes this behaviour.
This went unnoticed as neither the jz4740 nor the jz4780 CGU code
have clocks with fixed dividers yet.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18477/
Signed-off-by: James Hogan <jhogan@kernel.org>
The CGU common code does not modify the pointed clk_ops structure, so it
should be marked as const.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18476/
Signed-off-by: James Hogan <jhogan@kernel.org>
Changes from v1->v2:
Add 'select RESET_CONTROLLER' under COMMON_CLK_MEDIATEK and enable
reset.c to be built when COMMON_CLK_MEDIATEK is selected. That should
be quite reasonable because the reset controller is tightly embedded
inside and exported from these clock subsystems. At least it can be found
on infracfg and pericfg subsystem that both are really fundamental block
lots of devices must depend on.
commit 74cb0d6dde ("clk: mediatek: fixup test-building of MediaTek clock
drivers") can let the build system looking into the directory where the
clock drivers resides and then allow test-building the drivers.
But the change also gives rise to certain incorrect behavior which is
reset.c being built even not depending on either COMPILE_TEST or
ARCH_MEDIATEK alternative dependency. To get rid of reset.c being built
unexpectedly on the other platforms, it would be a good change that the
file should be built depending on its own specific configuration rather
than just on generic RESET_CONTROLLER one.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reentrant calls to clk_enable() are not working on UP systems. This is
caused by the fact spin_trylock_irqsave() always returns true when
CONFIG_SMP=n (and CONFIG_DEBUG_SPINLOCK=n) which causes the reference
counting to not work correctly when clk_enable_lock() is called twice
before clk_enable_unlock() is called (this happens when clk_enable()
is called from within another clk_enable()).
This fixes the problem by skipping the call to spin_trylock_irqsave() on UP
systems and relying solely on reference counting. We also make sure to set
flags in this case so that we are not returning an uninitialized value.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
platform_get_resource() may return NULL, add proper
check to avoid potential NULL dereferencing.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, matching the data
types.
Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.
clk_core.rate and .accuracy are "unsigned long", hence casting
their addresses to "u32 *" exposed the wrong halves on big-endian
64-bit systems. Fix this by using debugfs_create_ulong() instead.
Octal permissions are preferred, as they are easier to read than
symbolic permissions. Hence replace "S_IRUGO" by "0444"
throughout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[sboyd@codeaurora.org: Squash the octal change in too]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the virtual "clk_flags" file in debugfs shows the numeric
value of the top-level framework flags for the specified clock.
Hence the user must manually interpret these values.
Moreover, on big-endian 64-bit systems, the wrong half of the value is
shown, due to the cast from "unsigned long *" to "u32 *".
Fix both issues by showing the symbolic flag names instead.
Any non-standard flags are shown as a hex number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We can move these APIs into the private header file now that we
don't have any users of the __clk_get() and __clk_put() APIs
outside of clkdev.c and clk.c.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We'd like to privatize __clk_get(), but the sunxi clk driver is
calling this function to keep a reference held on the clk and
call clk_prepare_enable() on it. We support this design in the
clk core now with the CLK_IS_CRITICAL flag, so let's just use
that instead.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The "flags" parameter passed to of_clk_detect_critical() cannot be a
pointer to a real clk_core.flags field, as clk_core is private to the
clock framework internals.
Change the comment to refer to top-level framework flags instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
TCON1 also has M divider, contrary to TCON0. And the mux is only
2 bits wide, instead of 3.
Fixes: 05359be117 ("clk: sunxi-ng: Add driver for A83T CCU")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[wens@csie.org: Add description about mux width difference]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Now that all the users of asm/clkdev.h have been replaced with
the generic file we can get rid of the asm-generic file as well
and implement that code directly where it's used.
We only have one caller of __clkdev_alloc(), in clkdev.c so we
can easily remove that and drop the include of asm/clkdev.h in
linux/clkdev.h by putting the __clk_get/__clk_put inlines in
their respective location.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a driver for the APCS clock controller. It is part of the APCS
hardware block, which among other things implements also a combined
mux and half integer divider functionality. It can choose between a
fixed-rate clock or the dedicated APCS (A53) PLL. The source and the
divider can be set both at the same time.
This is required for enabling CPU frequency scaling on MSM8916-based
platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
[sboyd@codeaurora.org: Include rcg header for parent_map, drop
multiple unneeded includes, add COMPILE_TEST to APCS depends,
made tristate/modular]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for hardware that can switch both parent clock and divider
at the same time. This avoids generating intermediate frequencies from
either the old parent clock and new divider or new parent clock and
old divider combinations.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
[sboyd@codeaurora.org: Change a comment style, drop parent_map in
favor of a u32 array instead, export symbols for clk_ops and mux
function]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The CPUs on Qualcomm MSM8916-based platforms are clocked by two PLLs,
a primary (A53) CPU PLL and a secondary fixed-rate GPLL0. These sources
are connected to a mux and half-integer divider, which is feeding the
CPU cores.
This patch adds support for the primary CPU PLL which generates the
higher range of frequencies above 1GHz.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
[sboyd@codeaurora.org: Move to devm provider registration,
NUL terminate frequency table, made tristate/modular]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clocks of A64/H5 SoCs in the DE2 CCU is the same as the clocks in H3
DE2 CCU rather than the A83T DE2 CCU (the parent of them is the DE
module clock).
Fix this by change the clock descriptions to use the clocks of H3.
Fixes: 763c5bd045 ("clk: sunxi-ng: add support for DE2 CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner H3 features a DE2 CCU like the one on A83T, however the
parent of the clocks is the DE module clock, not the PLL_DE clock.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
divider_recalc_rate() is an helper function used by clock divider of
different types, so the structure containing the 'hw' pointer is not
always a 'struct clk_divider'
At the following line:
> div = _get_div(table, val, flags, divider->width);
in several cases, the value of 'divider->width' is garbage as the actual
structure behind this memory is not a 'struct clk_divider'
Fortunately, this width value is used by _get_val() only when
CLK_DIVIDER_MAX_AT_ZERO flag is set. This has never been the case so
far when the structure is not a 'struct clk_divider'. This is probably
why we did not notice this bug before
Fixes: afe76c8fd0 ("clk: allow a clk divider with max divisor when zero")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix ptr_ret.cocci warnings:
drivers/clk/mvebu/armada-37xx-periph.c:362:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There were a few fields in the iproc pll data structures that were
holding information that was not true state information.
Using stack variables is sufficient and simplifies the structure.
There are not any functional changes in this commit.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The iproc plls are capable of doing small rate changes without the
need for a full reset and re-lock procedure. This feature will
allow for small tweaks to the PLL rate to occur smoothly.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The pll post divider code was using DIV_ROUND_UP when determining the
divider value best suited to produce the target frequency.
Using DIV_ROUND_CLOSEST will give us better divider values when
the division results in a small remainder.
Also, change the post divider clock over to the determine_rate api
instead of round_rate.
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the ability for the iproc pll to calculate the pll parameters at
runtime instead of only using predefined tables. This ability allows
the clock users to select from the full range of vco frequencies.
The old method of table based programming is retained so that existing
users will retain expected behavior. The flag IPROC_CLK_PLL_CALC_PARAM
will need to be set to enable the new runtime calculation method.
Currently, this is only being enabled for the audio pll.
This feature also revealed a problem with the driver using the
round_rate api. The round_rate api does not allow for frequencies larger
than 2^31 to be returned. Those large frequencies are interpreted as an
error code. Therefore, we are moving to the determine_rate api which
solves this problem.
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since switching to clk drivers, the CLK_POUT cannot be searched for by
clk_get() API and thus it returns with ENOENT.
Register it with the clk_lookup and thus unbreak the users of it.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fixes the following sparse warning:
drivers/clk/meson/axg.c:260:25: warning:
symbol 'axg_gp0_params_table' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
David Lechner
Sudeep Holla
Ryder Lee
Amit Nischal
Srinivas Kandagatla
Weiyi Lu
Jeffy Chen
Shawn Lin
Richard Genoud
Mike Looijmans
Riku Voipio
Benjamin Gaignard
Patrice Chotard
Gabriel Fernandez
Katsuhiro Suzuki
Sean Wang
Gregory CLEMENT
Andy Shevchenko
Boris Brezillon
Icenowy Zheng
Fabio Estevam
Arnd Bergmann
Chunyan Zhang
Stephen Boyd
Lucas Stach
Brian Starkey
Stephen Boyd
Sylwester Nawrocki
Eddie James
Marek Szyprowski
Derek Basehore
Jacopo Mondi
Jerome Brunet
Neil Armstrong
Leonard Crestez
Wei Yongjun
Marcel Ziswiler
Dmitry Osipenko
tianshuliang
Peter De Schrijver
Tero Kristo
Jernej Skrabec
Anson Huang
Stefan Agner
Rui Miguel Silva
Jianguo Sun
Shawn Guo
Younian Wang
Andrzej Hajda
Sergei Shtylyov
Geert Uytterhoeven
Fabrizio Castro
Chen-Yu Tsai
Chanwoo Choi
Corentin Labbe
Takeshi Kihara
Zheng Yang
Heiko Stuebner
Yixun Lan
Linus Torvalds
Benjamin Herrenschmidt
Joel Stanley
Paul Cercueil
ABE Hiroshige
Georgi Djakov
Gomonovych, Vasyl
Lori Hikichi
Lori Hikichi
Wu Fengguang
Igor Grinberg