Per-CPU timers that are shutdown when a CPU is switched over must be disabled
upon switching and reprogrammed on the inbound CPU by relying on the
clock events management API. save/restore sequence is executed with irqs
disabled as mandated by the clock events API.
The next_event is an absolute time, hence, when the inbound CPU resumes,
if the timer has expired the min delta is forced into the tick device to
fire after few cycles.
This patch adds switching support for clock events that are per-CPU and
have to be migrated when a switch takes place; the cpumask of the clock
event device is checked against the cpumask of the current cpu, and if
they match, the clockevent device mode is saved and it is put in
shutdown mode. Resume code reprogrammes the tick device accordingly.
Tested on A15/A7 fast models and architected timers.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
This is the core code implementing big.LITTLE switcher functionality.
Rationale for this code is available here:
http://lwn.net/Articles/481055/
The main entry point for a switch request is:
void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id)
If the calling CPU is not the wanted one, this wrapper takes care of
sending the request to the appropriate CPU with schedule_work_on().
At the moment the core switch operation is handled by bL_switch_to()
which must be called on the CPU for which a switch is requested.
What this code does:
* Return early if the current cluster is the wanted one.
* Close the gate in the kernel entry vector for both the inbound
and outbound CPUs.
* Wake up the inbound CPU so it can perform its reset sequence in
parallel up to the kernel entry vector gate.
* Migrate all interrupts in the GIC targeting the outbound CPU
interface to the inbound CPU interface, including SGIs. This is
performed by gic_migrate_target() in drivers/irqchip/irq-gic.c.
* Call cpu_pm_enter() which takes care of flushing the VFP state to
RAM and save the CPU interface config from the GIC to RAM.
* Modify the cpu_logical_map to refer to the inbound physical CPU.
* Call cpu_suspend() which saves the CPU state (general purpose
registers, page table address) onto the stack and store the
resulting stack pointer in an array indexed by the updated
cpu_logical_map, then call the provided shutdown function.
This happens in arch/arm/kernel/sleep.S.
At this point, the provided shutdown function executed by the outbound
CPU ungates the inbound CPU. Therefore the inbound CPU:
* Picks up the saved stack pointer in the array indexed by its MPIDR
in arch/arm/kernel/sleep.S.
* The MMU and caches are re-enabled using the saved state on the
provided stack, just like if this was a resume operation from a
suspended state.
* Then cpu_suspend() returns, although this is on the inbound CPU
rather than the outbound CPU which called it initially.
* The function cpu_pm_exit() is called which effect is to restore the
CPU interface state in the GIC using the state previously saved by
the outbound CPU.
* Exit of bL_switch_to() to resume normal kernel execution on the
new CPU.
However, the outbound CPU is potentially still running in parallel while
the inbound CPU is resuming normal kernel execution, hence we need
per CPU stack isolation to execute bL_do_switch(). After the outbound
CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to:
* Clean its L1 cache.
* If it is the last CPU still alive in its cluster (last man standing),
it also cleans its L2 cache and disables cache snooping from the other
cluster.
* Power down the CPU (or whole cluster).
Code called from bL_do_switch() might end up referencing 'current' for
some reasons. However, 'current' is derived from the stack pointer.
With any arbitrary stack, the returned value for 'current' and any
dereferenced values through it are just random garbage which may lead to
segmentation faults.
The active page table during the execution of bL_do_switch() is also a
problem. There is no guarantee that the inbound CPU won't destroy the
corresponding task which would free the attached page table while the
outbound CPU is still running and relying on it.
To solve both issues, we borrow some of the task space belonging to
the init/idle task which, by its nature, is lightly used and therefore
is unlikely to clash with our usage. The init task is also never going
away.
Right now the logical CPU number is assumed to be equivalent to the
physical CPU number within each cluster. The kernel should also be
booted with only one cluster active. These limitations will be lifted
eventually.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
From Sekhar Nori:
DaVinci fixes for v3.11-rc2
The pull request includes fixes for sparse warnings, defconfig changes to
enable DMA usage on peripherals and removal of a duplicated include file.
* tag 'davinci-fixes-for-v3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: defconfig: enable EDMA driver
ARM: davinci: make file local variables static
ARM: edma: remove duplicated include from edma.c
Signed-off-by: Olof Johansson <olof@lixom.net>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code. It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
Pull ARM updates from Russell King:
"This contains the usual updates from other people (listed below) and
the usual random muddle of miscellaneous ARM updates which cover some
low priority bug fixes and performance improvements.
I've started to put the pull request wording into the merge commits,
which are:
- NoMMU stuff:
This includes the following series sent earlier to the list:
- nommu-fixes
- R7 Support
- MPU support
I've left out the ARCH_MULTIPLATFORM/!MMU stuff that Arnd and I
were discussing today until we've reached a conclusion/that's had
some more review.
This is rebased (and re-tested) on your devel-stable branch because
otherwise there were going to be conflicts with Uwe's V7M work now
that you've merged that. I've included the fix for limiting MPU to
CPU_V7.
- Huge page support
These changes bring both HugeTLB support and Transparent HugePage
(THP) support to ARM. Only long descriptors (LPAE) are supported
in this series.
The code has been tested on an Arndale board (Exynos 5250).
- LPAE updates
Please pull these miscellaneous LPAE fixes I've been collecting for
a while now for 3.11. They've been tested and reviewed by quite a
few people, and most of the patches are pretty trivial. -- Will Deacon.
- arch_timer cleanups
Please pull these arch_timer cleanups I've been holding onto for a
while. They're the same as my last posting, but have been rebased
to v3.10-rc3.
- mpidr linearisation (multiprocessor id register - identifies which
CPU number we are in the system)
This patch series that implements MPIDR linearization through a
simple hashing algorithm and updates current cpu_{suspend}/{resume}
code to use the newly created hash structures to retrieve context
pointers. It represents a stepping stone for the implementation of
power management code on forthcoming multi-cluster ARM systems.
It has been tested on TC2 (dual cluster A15xA7 system), iMX6q,
OMAP4 and Tegra, with processors hitting low-power states requiring
warm-boot resume through the cpu_resume code path"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
ARM: 7775/1: mm: Remove do_sect_fault from LPAE code
ARM: 7777/1: Avoid extra calls to the C compiler
ARM: 7774/1: Fix dtb dependency to use order-only prerequisites
ARM: 7770/1: remove residual ARMv2 support from decompressor
ARM: 7769/1: Cortex-A15: fix erratum 798181 implementation
ARM: 7768/1: prevent risks of out-of-bound access in ASID allocator
ARM: 7767/1: let the ASID allocator handle suspended animation
ARM: 7766/1: versatile: don't mark pen as __INIT
ARM: 7765/1: perf: Record the user-mode PC in the call chain.
ARM: 7735/2: Preserve the user r/w register TPIDRURW on context switch and fork
ARM: kernel: implement stack pointer save array through MPIDR hashing
ARM: kernel: build MPIDR hash function data structure
ARM: mpu: Ensure that MPU depends on CPU_V7
ARM: mpu: protect the vectors page with an MPU region
ARM: mpu: Allow enabling of the MPU via kconfig
ARM: 7758/1: introduce config HAS_BANDGAP
ARM: 7757/1: mm: don't flush icache in switch_mm with hardware broadcasting
ARM: 7751/1: zImage: don't overwrite ourself with a page table
ARM: 7749/1: spinlock: retry trylock operation if strex fails on free lock
ARM: 7748/1: oabi: handle faults when loading swi instruction from userspace
...
EDMA supports a cross bar which provides ability
to mux additional events into physical channels
present in the channel controller.
This is required when the number of events present
in the system are more than number of available
physical channels.
Changes by Joel:
* Split EDMA xbar support out of original EDMA DT parsing patch
to keep it easier for review.
* Rewrite shift and offset calculation.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Suggested by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[nsekhar@ti.com: fix checkpatch errors and a minor coding improvement]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Adds support for parsing the TI EDMA DT data into the required EDMA
private API platform data. Enables runtime PM support to initialize
the EDMA hwmod. Enables build on OMAP.
Changes by Joel:
* Setup default one-to-one mapping for queue_priority and queue_tc
mapping as discussed in [1].
* Split out xbar stuff to separate patch. [1]
* Dropped unused DT helper to convert to array
* Fixed dangling pointer issue with Sekhar's changes
[1] https://patchwork.kernel.org/patch/2226761/
Signed-off-by: Matt Porter <mporter@ti.com>
[nsekhar@ti.com: fix checkpatch errors, build breakages. Introduce
edma_setup_info_from_dt() as part of that effort]
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Use devm_ioremap_resource instead of reques_mem_region()/ioremap(),
devm_request_irq() instead of request_irq() and kzalloc() calls to
devm_kzalloc().
This ensures more consistent error values and simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
[nsekhar@ti.com: add missing err.h include]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Fix build on OMAP, the irqs are undefined on AM33xx.
These error interrupt handlers were hardcoded as disabled
so since they are unused code, simply remove them.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Move mach-davinci/dma.c to common/edma.c so it can be used
by OMAP (specifically AM33xx) as well.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Chris Ball <cjb@laptop.org> # davinci_mmc.c
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
[nsekhar@ti.com: dropped davinci sffsdr changes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
The smp_init_cpus method in the smp_operations structure is optional
and can be omitted entirely.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU and cluster numbers (MPIDR affinity levels 0 and 1) may have
at most 8 bits each.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM fixes from Russell King:
"A small number of fixes for stuff from the last merge window, and in
one case (IRQ time accounting) the previous merge window."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7720/1: ARM v6/v7 cmpxchg64 shouldn't clear upper 32 bits of the old/new value
ARM: 7715/1: MCPM: adapt to GIC changes after upstream merge
ARM: 7714/1: mmc: mmci: Ensure return value of regulator_enable() is checked
ARM: 7712/1: Remove trailing whitespace in arch/arm/Makefile
ARM: 7711/1: dove: fix Dove cpu type from V7 to PJ4
ARM: finally enable IRQ time accounting config
Since commit c0114709ed ("irqchip: gic: Perform the gic_secondary_init()
call via CPU notifier") it is no longer required nor possible to call
gic_secondary_init() from platform code.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle.
We normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time
we need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc cleanup
series because of interdependencies with timer drivers now moved out
of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes
for Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HWfp
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle. We
normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time we
need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc
cleanup series because of interdependencies with timer drivers now
moved out of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes for
Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10."
* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
ARM: SPEAr: conditionalize SMP code
ARM: arch_timer: Silence debug preempt warnings
ARM: OMAP: remove unused variable
serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
ata: arasan: remove the need for platform_data
ARM: at91/sama5d34ek.dts: remove not needed compatibility string
ARM: at91: dts: add MCI DMA support
ARM: at91: dts: add i2c dma support
ARM: at91: dts: set #dma-cells to the correct value
ARM: at91: suspend both memory controllers on at91sam9263
irqchip: armada-370-xp: slightly cleanup irq controller driver
irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
irqchip: move IRQ driver for Armada 370/XP
ARM: mvebu: move L2 cache initialization in init_early()
devtree: add binding documentation for sp804
ARM: integrator-cp: convert use CLKSRC_OF for timer init
ARM: versatile: use OF init for sp804 timer
ARM: versatile: add versatile dtbs to dtbs target
...
Two platforms, bcm and exynos have their own firmware interfaces using
the "secure monitor call", this adds support for those.
We had originally planned to have a third set of patches in here, which
would extend support for the existing generic "psci" call that is used
on multiple platforms as well as Xen and KVM guests, but that ended up
getting dropped because the patches were not ready in time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=68m5
-----END PGP SIGNATURE-----
Merge tag 'firmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM platform specific firmware interfaces from Olof Johansson:
"Two platforms, bcm and exynos have their own firmware interfaces using
the "secure monitor call", this adds support for those.
We had originally planned to have a third set of patches in here,
which would extend support for the existing generic "psci" call that
is used on multiple platforms as well as Xen and KVM guests, but that
ended up getting dropped because the patches were not ready in time."
* tag 'firmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm: mark bcm_kona_smc_init as __init
ARM: bcm281xx: Add DT support for SMC handler
ARM: bcm281xx: Add L2 cache enable code
ARM: EXYNOS: Add secure firmware support to secondary CPU bring-up
ARM: EXYNOS: Add IO mapping for non-secure SYSRAM.
ARM: EXYNOS: Add support for Exynos secure firmware
ARM: EXYNOS: Add support for secure monitor calls
ARM: Add interface for registering and calling firmware-specific operations
The full mcpm layer is not likely to be relevant to v6 based
platforms, so a multiplatform kernel won't use that code if booted
on v6 hardware.
This patch modifies the AFLAGS for affected mcpm .S files to
specify armv7-a explicitly for that code.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the cluster power API is in place, we can use it for SMP secondary
bringup and CPU hotplug in a generic fashion.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Instead of requiring the first man to be elected in advance (which
can be suboptimal in some situations), this patch uses a per-
cluster mutex to co-ordinate selection of the first man.
This should also make it more feasible to reuse this code path for
asynchronous cluster resume (as in CPUidle scenarios).
We must ensure that the vlock data doesn't share a cacheline with
anything else, or dirty cache eviction could corrupt it.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This patch adds a simple low-level voting mutex implementation
to be used to arbitrate during first man selection when no load/store
exclusive instructions are usable.
For want of a better name, these are called "vlocks". (I was
tempted to call them ballot locks, but "block" is way too confusing
an abbreviation...)
There is no function to wait for the lock to be released, and no
vlock_lock() function since we don't need these at the moment.
These could straightforwardly be added if vlocks get used for other
purposes.
For architectural correctness even Strongly-Ordered memory accesses
require barriers in order to guarantee that multiple CPUs have a
coherent view of the ordering of memory accesses. Whether or not
this matters depends on hardware implementation details of the
memory system. Since the purpose of this code is to provide a clean,
generic locking mechanism with no platform-specific dependencies the
barriers should be present to avoid unpleasant surprises on future
platforms.
Note:
* When taking the lock, we don't care about implicit background
memory operations and other signalling which may be pending,
because those are not part of the critical section anyway.
A DMB is sufficient to ensure correctly observed ordering if
the explicit memory accesses in vlock_trylock.
* No barrier is required after checking the election result,
because the result is determined by the store to
VLOCK_OWNER_OFFSET and is already globally observed due to the
barriers in voting_end. This means that global agreement on
the winner is guaranteed, even before the winner is known
locally.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This provides helper methods to coordinate between CPUs coming down
and CPUs going up, as well as documentation on the used algorithms,
so that cluster teardown and setup
operations are not done for a cluster simultaneously.
For use in the power_down() implementation:
* __mcpm_cpu_going_down(unsigned int cluster, unsigned int cpu)
* __mcpm_outbound_enter_critical(unsigned int cluster)
* __mcpm_outbound_leave_critical(unsigned int cluster)
* __mcpm_cpu_down(unsigned int cluster, unsigned int cpu)
The power_up_setup() helper should do platform-specific setup in
preparation for turning the CPU on, such as invalidating local caches
or entering coherency. It must be assembler for now, since it must
run before the MMU can be switched on. It is passed the affinity level
for which initialization should be performed.
Because the mcpm_sync_struct content is looked-up and modified
with the cache enabled or disabled depending on the code path, it is
crucial to always ensure proper cache maintenance to update main memory
right away. The sync_cache_*() helpers are used to that end.
Also, in order to prevent a cached writer from interfering with an
adjacent non-cached writer, we ensure each state variable is located to
a separate cache line.
Thanks to Nicolas Pitre and Achin Gupta for the help with this
patch.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This is the basic API used to handle the powering up/down of individual
CPUs in a (multi-)cluster system. The platform specific backend
implementation has the responsibility to also handle the cluster level
power as well when the first/last CPU in a cluster is brought up/down.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
CPUs in cluster based systems, such as big.LITTLE, have special needs
when entering the kernel due to a hotplug event, or when resuming from
a deep sleep mode.
This is vectorized so multiple CPUs can enter the kernel in parallel
without serialization.
The mcpm prefix stands for "multi cluster power management", however
this is usable on single cluster systems as well. Only the basic
structure is introduced here. This will be extended with later patches.
In order not to complexify things more than they currently have to,
the planned work to make runtime adjusted MPIDR based indexing and
dynamic memory allocation for cluster states is postponed to a later
cycle. The MAX_NR_CLUSTERS and MAX_CPUS_PER_CLUSTER static definitions
should be sufficient for those systems expected to be available in the
near future.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Move the integrator-cp timer init to timer-sp.c and use CLKSRC_OF. There is
no reason to use the aliases, so drop them from the init code.
The integrator-cp timers are mistakenly called sp804 timers in the dts, but
in fact they are not sp804 dual timers, but single timers with the same
programming model. Fix the dts to reflect this.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This adds CLKSRC_OF based init for sp804 timer. The clock initialization is
refactored to support retrieving the clock(s) from the DT.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Some boards are running with secure firmware running in TrustZone secure
world, which changes the way some things have to be initialized.
This patch adds an interface for platforms to specify available firmware
operations and call them.
A wrapper macro, call_firmware_op(), checks if the operation is provided
and calls it if so, otherwise returns -ENOSYS to allow fallback to
legacy operation..
By default no operations are provided.
Example of use:
In code using firmware ops:
__raw_writel(virt_to_phys(exynos4_secondary_startup),
CPU1_BOOT_REG);
/* Call Exynos specific smc call */
if (call_firmware_op(cpu_boot, cpu) == -ENOSYS)
cpu_boot_legacy(...); /* Try legacy way */
gic_raise_softirq(cpumask_of(cpu), 1);
In board-/platform-specific code:
static int platformX_do_idle(void)
{
/* tell platformX firmware to enter idle */
return 0;
}
static int platformX_cpu_boot(int i)
{
/* tell platformX firmware to boot CPU i */
return 0;
}
static const struct firmware_ops platformX_firmware_ops = {
.do_idle = exynos_do_idle,
.cpu_boot = exynos_cpu_boot,
/* other operations not available on platformX */
};
static void __init board_init_early(void)
{
register_firmware_ops(&platformX_firmware_ops);
}
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that we have drivers/irqchip, move VIC irqchip to drivers/irqchip.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Now that the VIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static. Move vic_handle_irq
to avoid a forward declaration.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hubert Feurstein <hubert.feurstein@contec.at>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Set handle_arch_irq to vic_handle_irq. Only the first VIC initialized can
setup the handler.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Olof Johansson <olof@lixom.net>
Move all register defines except VIC_INT_ENABLE and VIC_INT_ENABLE_CLEAR
which are used by Samsung.
With multi irq handler, vic.h is not included in assembly any more, so
we can remove the assembly ifdefs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Olof Johansson <olof@lixom.net>
Now that we have drivers/irqchip, move GIC irqchip to drivers/irqchip. This
is necessary to share the GIC with arm and arm64.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Now that the GIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Set handle_arch_irq to gic_handle_irq. Only the first GIC initialized can
setup the handler.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Olof Johansson <olof@lixom.net>
In preparation of moving gic code to drivers/irqchip, remove the direct
platform dependencies on gic_raise_softirq. Move the setup of
smp_cross_call into the gic code and use arch_send_wakeup_ipi_mask
function to trigger wake-up IPIs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7616/1: cache-l2x0: aurora: Use writel_relaxed instead of writel
ARM: 7615/1: cache-l2x0: aurora: Invalidate during clean operation with WT enable
ARM: 7614/1: mm: fix wrong branch from Cortex-A9 to PJ4b
ARM: 7612/1: imx: Do not select some errata that depends on !ARCH_MULTIPLATFORM
ARM: 7611/1: VIC: fix bug in VIC irqdomain code
ARM: 7610/1: versatile: bump IRQ numbers
ARM: 7609/1: disable errata work-arounds which access secure registers
ARM: 7608/1: l2x0: Only set .set_debug on PL310 r3p0 and earlier
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VIC irqdomain code added in commit
07c9249f1f
"ARM: 7554/1: VIC: use irq_domain_add_simple()"
Had two bugs:
1) It didn't call irq_create_mapping() once on each
valid irq source in the slowpath when registering
the controller.
2) It passed a -1 as IRQ offset for the DT case, whereas
0 should be passed as invalid IRQ instead.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SP804 driver statically initialises the cpumask of the clock event
device to be cpu_all_mask, which is derived from the compile-time
constant NR_CPUS. This breaks SMP_ON_UP systems where the interrupt
controller handling the sp804 doesn't have the irq_set_affinity callback
on the irq_chip, because the common timer code fails to identify the
device as cpu-local and ends up treating it as a broadcast device
instead.
This patch fixes the problem by using cpu_possible_mask at runtime,
which will correctly represent the possible CPUs when SMP_ON_UP is being
used.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GIC interface numbering does not necessarily follow the logical
CPU numbering, especially for complex topologies such as multi-cluster
systems.
Fortunately we can easily probe the GIC to create a mapping as the
Interrupt Processor Targets Registers for the first 32 interrupts are
read-only, and each field returns a value that always corresponds to
the processor reading the register.
Initially all mappings target all CPUs in case an IPI is required to
boot secondary CPUs. It is refined as those CPUs discover what their
actual mapping is.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
07c9249f1f (ARM: 7554/1: VIC: use irq_domain_add_simple()) removed the
use of 'irq_base' but did not remove the variable itself, which causes:
arch/arm/common/vic.c: In function 'vic_of_init':
arch/arm/common/vic.c:410:6: warning: unused variable 'irq_base'
Remove this now unused variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instead of allocating descriptors on-the-fly for the device tree
initialization case, use irq_domain_add_simple() which will take
care of this if you pass negative as the first_irq.
Alter the signature of __vic_init() to pass the first_irq as
signed so this works as expected.
Switching the VIC to use irq_domain_add_simple() also has the
upside of displaying the same WARNING when you boot with
pre-allocated descriptors on systems using SPARSE_IRQ but
yet not using device tree.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The it8152 PCI host used on the pxa/cm_x2xx machines
uses the old-style I/O window registration. This should
eventually get converted to pci_ioremap_io() but for
now, let's cast the IT8152_IO_BASE constant to an integer
type to get rid of the warnings.
Without this patch, building cm_x2xx_defconfig results in:
arch/arm/common/it8152.c: In function 'it8152_pci_setup':
arch/arm/common/it8152.c:287:18: warning: assignment makes integer from pointer without a cast [enabled by default]
arch/arm/common/it8152.c:288:16: warning: assignment makes integer from pointer without a cast [enabled by default]
arch/arm/common/it8152.c:291:17: warning: assignment makes integer from pointer without a cast [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for dma_get_sgtable() function which is required
to let drivers to share the buffers allocated by DMA-mapping subsystem.
Generic implementation based on virt_to_page() is not suitable for ARM
dma-mapping subsystem.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch fixes the usage of uninitialized variables in dmabounce code
intoduced by commit a227fb92 ('ARM: dma-mapping: remove offset parameter
to prepare for generic dma_ops'):
arch/arm/common/dmabounce.c: In function ‘dmabounce_sync_for_device’:
arch/arm/common/dmabounce.c:409: warning: ‘off’ may be used uninitialized in this function
arch/arm/common/dmabounce.c:407: note: ‘off’ was declared here
arch/arm/common/dmabounce.c: In function ‘dmabounce_sync_for_cpu’:
arch/arm/common/dmabounce.c:369: warning: ‘off’ may be used uninitialized in this function
arch/arm/common/dmabounce.c:367: note: ‘off’ was declared here
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Pull CMA and ARM DMA-mapping updates from Marek Szyprowski:
"These patches contain two major updates for DMA mapping subsystem
(mainly for ARM architecture). First one is Contiguous Memory
Allocator (CMA) which makes it possible for device drivers to allocate
big contiguous chunks of memory after the system has booted.
The main difference from the similar frameworks is the fact that CMA
allows to transparently reuse the memory region reserved for the big
chunk allocation as a system memory, so no memory is wasted when no
big chunk is allocated. Once the alloc request is issued, the
framework migrates system pages to create space for the required big
chunk of physically contiguous memory.
For more information one can refer to nice LWN articles:
- 'A reworked contiguous memory allocator':
http://lwn.net/Articles/447405/
- 'CMA and ARM':
http://lwn.net/Articles/450286/
- 'A deep dive into CMA':
http://lwn.net/Articles/486301/
- and the following thread with the patches and links to all previous
versions:
https://lkml.org/lkml/2012/4/3/204
The main client for this new framework is ARM DMA-mapping subsystem.
The second part provides a complete redesign in ARM DMA-mapping
subsystem. The core implementation has been changed to use common
struct dma_map_ops based infrastructure with the recent updates for
new dma attributes merged in v3.4-rc2. This allows to use more than
one implementation of dma-mapping calls and change/select them on the
struct device basis. The first client of this new infractructure is
dmabounce implementation which has been completely cut out of the
core, common code.
The last patch of this redesign update introduces a new, experimental
implementation of dma-mapping calls on top of generic IOMMU framework.
This lets ARM sub-platform to transparently use IOMMU for DMA-mapping
calls if one provides required IOMMU hardware.
For more information please refer to the following thread:
http://www.spinics.net/lists/arm-kernel/msg175729.html
The last patch merges changes from both updates and provides a
resolution for the conflicts which cannot be avoided when patches have
been applied on the same files (mainly arch/arm/mm/dma-mapping.c)."
Acked by Andrew Morton <akpm@linux-foundation.org>:
"Yup, this one please. It's had much work, plenty of review and I
think even Russell is happy with it."
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: (28 commits)
ARM: dma-mapping: use PMD size for section unmap
cma: fix migration mode
ARM: integrate CMA with DMA-mapping subsystem
X86: integrate CMA with DMA-mapping subsystem
drivers: add Contiguous Memory Allocator
mm: trigger page reclaim in alloc_contig_range() to stabilise watermarks
mm: extract reclaim code from __alloc_pages_direct_reclaim()
mm: Serialize access to min_free_kbytes
mm: page_isolation: MIGRATE_CMA isolation functions added
mm: mmzone: MIGRATE_CMA migration type added
mm: page_alloc: change fallbacks array handling
mm: page_alloc: introduce alloc_contig_range()
mm: compaction: export some of the functions
mm: compaction: introduce isolate_freepages_range()
mm: compaction: introduce map_pages()
mm: compaction: introduce isolate_migratepages_range()
mm: page_alloc: remove trailing whitespace
ARM: dma-mapping: add support for IOMMU mapper
ARM: dma-mapping: use alloc, mmap, free from dma_ops
ARM: dma-mapping: remove redundant code and do the cleanup
...
Conflicts:
arch/x86/include/asm/dma-mapping.h
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
This patch converts dma_alloc/free/mmap_{coherent,writecombine}
functions to use generic alloc/free/mmap methods from dma_map_ops
structure. A new DMA_ATTR_WRITE_COMBINE DMA attribute have been
introduced to implement writecombine methods.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
This patch removes dma bounce hooks from the common dma mapping
implementation on ARM architecture and creates a separate set of
dma_map_ops for dma bounce devices.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
This patch removes the need for the offset parameter in dma bounce
functions. This is required to let dma-mapping framework on ARM
architecture to use common, generic dma_map_ops based dma-mapping
helpers.
Background and more detailed explaination:
dma_*_range_* functions are available from the early days of the dma
mapping api. They are the correct way of doing a partial syncs on the
buffer (usually used by the network device drivers). This patch changes
only the internal implementation of the dma bounce functions to let
them tunnel through dma_map_ops structure. The driver api stays
unchanged, so driver are obliged to call dma_*_range_* functions to
keep code clean and easy to understand.
The only drawback from this patch is reduced detection of the dma api
abuse. Let us consider the following code:
dma_addr = dma_map_single(dev, ptr, 64, DMA_TO_DEVICE);
dma_sync_single_range_for_cpu(dev, dma_addr+16, 0, 32, DMA_TO_DEVICE);
Without the patch such code fails, because dma bounce code is unable
to find the bounce buffer for the given dma_address. After the patch
the above sync call will be equivalent to:
dma_sync_single_range_for_cpu(dev, dma_addr, 16, 32, DMA_TO_DEVICE);
which succeeds.
I don't consider this as a real problem, because DMA API abuse should be
caught by debug_dma_* function family. This patch lets us to simplify
the internal low-level implementation without chaning the driver visible
API.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
Replace all uses of ~0 with DMA_ERROR_CODE, what should make the code
easier to read.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
Most PCI implementations perform simple root bus scanning. Rather than
having each group of platforms provide a duplicated bus scan function,
provide the PCI configuration ops structure via the hw_pci structure,
and call the root bus scanning function from core ARM PCI code.
Acked-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This removes the internal functions for assigning IRQ
handlers to each interrupt in favor of using the internal
map iterator in the irq domain code.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current IRQ domain implementation in the VIC allocates 32
interrupts for each VIC instance no matter whether the
controller actually use all the IRQs or not. Alter this so
we only allocate a domain up until the last IRQ marked valid.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPjYz4AAoJEAf03oE53VmQ/0wH/3kXJYM/8nX8fqlQ8eTh0SHi
lRsoNL+4arHFKcocYhZyiXEidUKCUMLuQSdvL9MWy1e286+ABsaFgrjfLsp/ZDqE
jDJBCZIxUD6rL94VRnYEHrhWqGzzPKi8/syVZ8JOv/1HGml402CqPcRDKmWY/e4Q
ajl/d463q0ufwfQ4LMP+DsR29TxEdecs4DkxnhwcrRCbJ2hDPLmWVER+tPITPwqp
R8qVGY3K6axG68b964B/hsACjRF7C1lqRQsiQbi8pVPPGEhekmgnW8hF6dNdy1VW
wVo8F0GCST6jLk9YFbirBdKsDRJTLc+WsyP6jUZyWkrrM6p4ycs+voGFDNZbhPw=
=CXyd
-----END PGP SIGNATURE-----
Merge tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
Nicolas Ferre <nicolas.ferre@atmel.com> writes:
First batch of AT91 cleanup for 3.5 kernel.
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
* tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91: (19 commits)
ARM: at91: add defconfig for device tree
ARM: at91/dt: do not specify the board any more
ARN: at91: introduce SOC_AT91xxx define to allow to compile SoC core support
ARM: at91: add SOC_AT91SAM9 kconfig option to factorise select
ARM: at91: pm select memory controler at runtime
ARM: at91: move at91_init_leds to board init
ARM: at91: do not pin mux the UARTs in init_early
ARM: at91: drop at91_set_serial_console
ARM: at91: uncompress: autodetect the uart to use
ARM: at91: uncompress Store UART address in a variable
hwrng: Kconfig: remove dependency for atmel-rng driver
Input: Kconfig: remove dependency for atmel_tsadcc driver
rtc: Kconfig: remove dependency for AT91 rtc driver
ARM: at91/Kconfig: website link for AT91SAM9G20-EK
ARM: at91/Kconfig: add AT91SAM9x5 family to AT91_EARLY_DBGU0 entry
ARM: at91/Kconfig: add clarifications to AT91SAM9M10G45-EK entry
ARM: at91/Kconfig: add comment to at91sam9x5 family entry
ARM: at91/Kconfig: change at91sam9g45 entry
ARM: at91: change AT91 Kconfig entry comment
Also updates the cleanup branch to v3.4-rc3.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
handle_IRQ may briefly cause interrupts to be re-enabled during soft IRQ
processing on the exit path, leading to nested handling of VIC interrupts.
Since the current code does not re-read the VIC_IRQ_STATUS register, this
can lead to multiple invocations of the same interrupt handler and
spurious interrupts to be reported.
This patch changes the VIC interrupt dispatching code to re-read the
status register each time, avoiding duplicate invocations of the same
handler.
Acked-and-Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ixp2xxx platforms have had no real changes since ~2006 and the maintainer
has said on irc that they can be removed:
13:05 < nico> do you still care about ixp2000?
13:22 < lennert> not really, no
13:58 < nico> do you think we could remove it from the kernel tree?
14:01 < lennert> go for it, and remove ixp23xx too while you're at it
Removing will help simplify ARM consolidation in general and PCI re-work
specifically.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Disintegrate asm/system.h for ARM.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
These changes are all specific to an soc family or the code for
one soc. Lots of work for Tegra3 this time, but also a lot of other
platforms. There will be another (smaller) set of soc patches later in
the merge window for stuff that has dependencies on external trees or
that was sent just before the merge window opened.
The asoc tree added a few devices to the i.mx platform, which conflict
with other devices added in the same place here.
The tegra Makefile conflicts between a number of branches, mostly because
of changes regarding localtimer.c, which was removed in the end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WdYR
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC specific updates" from Arnd Bergmann:
"These changes are all specific to an soc family or the code for one
soc. Lots of work for Tegra3 this time, but also a lot of other
platforms. There will be another (smaller) set of soc patches later
in the merge window for stuff that has dependencies on external trees
or that was sent just before the merge window opened.
The asoc tree added a few devices to the i.mx platform, which conflict
with other devices added in the same place here.
The tegra Makefile conflicts between a number of branches, mostly
because of changes regarding localtimer.c, which was removed in the
end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up some trivial conflicts, including the mentioned Tegra Makefile.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: EXYNOS: fix cycle count for periodic mode of clock event timers
ARM: EXYNOS: add support JPEG
ARM: EXYNOS: Add DMC1, allow PPMU access for DMC
ARM: SAMSUNG: Correct MIPI-CSIS io memory resource definition
ARM: SAMSUNG: fix __init attribute on regarding s3c_set_platdata()
ARM: SAMSUNG: Add __init attribute to samsung_bl_set()
ARM: S5PV210: Add usb otg phy control
ARM: S3C64XX: Add usb otg phy control
ARM: EXYNOS: Enable l2 configuration through device tree
ARM: EXYNOS: remove useless code to save/restore L2
ARM: EXYNOS: save L2 settings during bootup
ARM: S5P: add L2 early resume code
ARM: EXYNOS: Add support AFTR mode on EXYNOS4210
ARM: mx35: Setup the AIPS registers
ARM: mx5: Use common function for configuring AIPS
ARM: mx3: Setup AIPS registers
ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI
ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
ARM: imx: update imx_v6_v7_defconfig
ARM: tegra: Demote EMC clock inconsistency BUG to WARN
...
Use dev_err() to report device specific errors rather than printk().
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the releasing of resources out of the release function - this
allows a cleaner and more conventional arrangement of the registration
failure paths and a saner unregistration process for these devices.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's pointless registering the PS/2 interfaces with the dmabounce code
when there's no DMA support for these in hardware, so only setup the
DMA masks for two subdevices which support DMA - the OHCI and SAC.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the bus notifier to register sa1111 devices with dmabounce, rather
than after the device has been registered, potentially racing with
driver binding.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some platforms don't want certain devices to be registered, because,
eg, the interface is not wired. Provide a way for platforms to
prevent various devices from being registered via a devid bitmask in
the platform data.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The irq_start and hwirq_base assignment code is fairly hairy and ended
up being difficult to read following a conflict resolution for 3.2.
This patch rearranges the code slightly to make it easier to read.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ruGA
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull irq_domain support for all architectures from Grant Likely:
"Generialize powerpc's irq_host as irq_domain
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
dt: fix twl4030 for non-dt compile on x86
mfd: twl-core: Add IRQ_DOMAIN dependency
devicetree: Add empty of_platform_populate() for !CONFIG_OF_ADDRESS (sparc)
irq_domain: Centralize definition of irq_dispose_mapping()
irq_domain/mips: Allow irq_domain on MIPS
irq_domain/x86: Convert x86 (embedded) to use common irq_domain
ppc-6xx: fix build failure in flipper-pic.c and hlwd-pic.c
irq_domain/microblaze: Convert microblaze to use irq_domains
irq_domain/powerpc: Replace custom xlate functions with library functions
irq_domain/powerpc: constify irq_domain_ops
irq_domain/c6x: Use library of xlate functions
irq_domain/c6x: constify irq_domain structures
irq_domain/c6x: Convert c6x to use generic irq_domain support.
irq_domain: constify irq_domain_ops
irq_domain: Create common xlate functions that device drivers can use
irq_domain: Remove irq_domain_add_simple()
irq_domain: Remove 'new' irq_domain in favour of the ppc one
mfd: twl-core.c: Fix the number of interrupts managed by twl4030
of/address: add empty static inlines for !CONFIG_OF
irq_domain: Add support for base irq and hwirq in legacy mappings
...
Currently there were two part of DMAC PL330 driver for
support old styled s3c-pl330 which has been merged into
drivers/dma/pl330.c driver. Actually, there is no reason
to separate them now.
Basically this patch merges arch/arm/common/pl330.c into
drivers/dma/pl330.c driver and removes useless exported
symbol, externed function and so on.
The newer pl330 driver tested on SMDKV310 and SMDK4212 boards
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The patch series to re-factor PCI's 'latency timer' setup (re:
http://marc.info/?l=linux-kernel&m=131983853831049&w=2) forgot to
remove the ARM specific definition of 'pcibios_max_latency' once such
had been moved into the pci core resulting in ARM related compile
errors -
drivers/built-in.o:(.data+0x230): multiple definition of
`pcibios_max_latency'
arch/arm/common/built-in.o:(.data+0x40c): first defined here
make[1]: *** [vmlinux.o] Error 1
In the series, patch 2/16 (commit 168c8619fd) converted the ARM
specific version of 'pcibios_set_master()' to a non-inlined version.
This was done in preperation for hosting it up into PCI's core, which
was done in patch 10/16 (commit 96c5590058) of the series (and
where the removal of ARM's 'pcibios_max_latency' was overlooked).
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the simplistic implementation of irq_domains and enables
the powerpc infrastructure for all irq_domain users. The powerpc
infrastructure includes support for complex mappings between Linux and
hardware irq numbers, and can manage allocation of irq_descs.
This patch also converts the few users of irq_domain_add()/irq_domain_del()
to call irq_domain_add_legacy() instead.
v3: Fix bug that set up too many irqs in translation range.
v2: Fix removal of irq_alloc_descs() call in gic driver
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
This fixes the thrd->req_running field being accessed before thrd
is checked for null. The error was introduced in
abb959f: ARM: 7237/1: PL330: Fix driver freeze
Reference: <1326458191-23492-1-git-send-email-mans.rullgard@linaro.org>
Cc: stable@kernel.org
Signed-off-by: Mans Rullgard <mans.rullgard@linaro.org>
Acked-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Part of the series to unify the irq remapping mechanisms in the
kernel. A follow up patch will copy the powerpc implementation into
kernel/irq/irqdomain.c, which will be a lot easier if the structures
are identical.
Where they differ, I've chose to use the powerpc names since there is
a lot more code using those names.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Add a sched_clock support for the sp804 timer. The clocksource timer
can optionally initialize itself as sched_clock timer.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Change the sa1111 device id to be a bitmask. This allows us to
specify the actual device, while allowing a single driver to bind
to both PS2 devices.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform hooks to be called when individual sa1111 devices are
enabled and disabled. This will allow us to move some platform
specifics out of the individual drivers.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a shutdown hook to the sa1111_driver structure to allow drivers
to be notified of system reboots and shutdowns.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement the necessary allocation/freeing functionality to support
sparse IRQs with the SA-1111 device. On non-sparse IRQ platforms,
this allows us to dynamically allocate from within the available IRQ
number space.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 19851c58e6 (sa1111: allow cascaded IRQs to be used by platforms)
moved the IRQ definitions to the .c file, and added an irq_base member
to the private data structure.
The inerrupt demultiplexer uses irq_base, but the interrupt setup code
does not. Also, although the commit adds a private data structure to
pass this data, it isn't even referenced, resulting in irq_base being
zero.
We also copied the IRQ numbers from the device info array into the actual
devices, resulting in wrong interrupt numbers passed to the sub-devices.
The net effect of this is that we always overwrite IRQs 0-54, even if
they are allocated elsewhere in the system.
Add the code necessary to setup the private irq_base, and use it in the
IRQ setup code. Make the SA-1111 probe fail with -EINVAL if there is no
platform data provided.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add an initializer for the struct device_driver .owner member.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We should not write to the SA1111 registers after setting the SLEEP
bit. Moreover, the manual says that the PWM registers should be
disabled before we enter sleep. So, move the clearing of these
registers earlier in the suspend sequence.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We weren't re-enabling the memory request/grant signals on resume,
causing DMA devices on the sa1111 to fail.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It turns out that the logical CPU mapping is useful even when !CONFIG_SMP
for manipulation of devices like interrupt and power controllers when
running a UP kernel on a CPU other than 0. This can happen when kexecing
a UP image from an SMP kernel.
In the future, multi-cluster systems running AMP configurations will
require something similar for mapping cluster IDs, so it makes sense to
decouple this logic in preparation for this support.
Acked-by: Yang Bai <hamo.by@gmail.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups. This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch converts ARM's architecture-specific inlined
'pcibios_set_master()' routine to a non-inlined function. This will
allow follow on patches to create a generic 'pcibios_set_master()'
function using the '__weak' attribute which can be used by all
architectures as a default which, if necessary, can then be over-
ridden by architecture-specific code.
Converting 'pci_bios_set_master()' to a non-inlined function will allow
ARM's 'pcibios_set_master()' implementation to remain architecture-
specific after the generic version is introduced and thus, not change
current behavior.
Note that ARM also has a non-inlined 'pcibios_set_master()' that is
used if CONFIG_PCI_HOST_ITE8152 is defined. This patch does not
change any behavior here either.
No functional change.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Now that irq_domain_simple_ops are available for non-DT users, use them
in the VIC driver so that we don't get a NULL dereference in
irq_domain_to_irq() when registering the domain.
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a request has finished successfully and we are about to call its
callback, remove its pointer from the corresponding pl330_thread .
This prevents the core driver from calling its callback again if
pl330_release_channel() is called without first flushing the device.
When pl330_update() returns, the driver is allowed to free the pointer
to pl330_req so the core driver shouldn't be able to access it again.
Reference: <CAJe_ZhftO+481BfL0ErEcM_brfmSuTXkTEniLRYxxM2T7OM2QA@mail.gmail.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a req_running field to the pl330_thread to track which request (if
any) has been submitted to the DMA. This mechanism replaces the old
one in which we tried to guess the same by looking at the PC of the
DMA, which could prevent the driver from sending more requests if it
didn't guess correctly.
Reference: <1323631637-9610-1-git-send-email-javi.merino@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This removes the hardcoded shift value and lets the clockevent core
come up with suitable mult and div factors. Tested on the
Integrator/CP.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When probing the VIC, the ST variant has a different probing method to
account for the extra interrupts which meant we didn't previously call
vic_register() which registered the irq_domain.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 4294f8baa ("ARM: gic: add irq_domain support") defines irq_start
as irq_start = (irq_start & ~31) + 16; On a platform with a GIC and a
CPU without PPIs, this results in irq_start being off by 16.
This patch fixes gic_init so that we only carve out a PPI space when
PPIs exist for the GIC being initialised.
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When multiple GICs exist on a platform (RealView PB1176/11MP),
we must make sure the PM notifier block is only registered
once, otherwise we end up corrupting the PM notifier list.
The fix is to only register the notifier when initializing
the first GIC, as the power management functions seem
to iterate over all the registered GICs.
Tested on PB11MP and PB1176.
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
scctl should be shifted by CC_SRCCTRL_SHFT and dcctl by
CC_DSTCCTRL_SHFT, not the other way round.
Reference: <1320244259-10496-4-git-send-email-javi.merino@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the manager is running non-secure, the only channels that can
issue interrupts are the ones that have a 1 in their corresponding bit
in Configuration Register 3. The other ones will generate an abort
when trying to signal the end of the transaction so they are useless
in non-secure mode.
Reference: <1320244259-10496-2-git-send-email-javi.merino@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that all platforms are converted to MULTI_IRQ_HANDLER, remove the
legacy support.
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Add a handler for the VIC that is suitable for MULTI_IRQ_HANDLER
platforms. This can replace the ASM entry macros for platforms that use
the VIC.
v4: - rebase ontop of move __exception and friends to
asm/exception.h
- rework polling loop to handle as many irqs as possible in one go
v3: - simplify irq handling loop as suggested by Grant
- service interrupts from msb->lsb order
v2: - allow the handler be used for !CONFIG_OF
- use irq_domain_to_irq()
Cc: Rob Herring <robherring2@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
This adds a device tree binding for the VIC based on the of_irq_init()
support. This adds an irqdomain to the vic and always registers all
vics in the static vic array rather than for pm only to keep track of
the irq domain. struct irq_data::hwirq is used where appropriate rather
than runtime masking.
v3: - include linux/export.h for THIS_MODULE
v2: - use irq_domain_simple_ops
- remove stub implementation of vic_of_init for !CONFIG_OF
- Make VIC select IRQ_DOMAIN
Reviewed-by: Rob Herring <robherring2@gmail.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Now that MULTI_IRQ_HANDLER is selected by all the in-tree
GIC users, make it mandatory and remove the unused macros.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Provide the GIC code with a low level handler that can be used
by platforms using CONFIG_MULTI_IRQ_HANDLER.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The GIC support code is heavily using the fact that hardware
implementations are exposing banked registers. Unfortunately, it
looks like at least one GIC implementation (EXYNOS) offers both
the distributor and the CPU interfaces at different addresses,
depending on the CPU.
This problem is solved by allowing the distributor and CPU interface
addresses to be per-cpu variables for the platforms that require it.
The EXYNOS code is updated not to mess with the GIC internals while
handling interrupts, and struct gic_chip_data is back to being private.
The DT binding for the gic is updated to allow an optional "cpu-offset"
value, which is used to compute the various base addresses.
Finally, a new config option (GIC_NON_BANKED) is used to control this
feature, so the overhead is only present on kernels compiled with
support for EXYNOS.
Tested on Origen (EXYNOS4) and Panda (OMAP4).
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
ARM: gic: use module.h instead of export.h
ARM: gic: fix irq_alloc_descs handling for sparse irq
ARM: gic: add OF based initialization
ARM: gic: add irq_domain support
irq: support domains with non-zero hwirq base
of/irq: introduce of_irq_init
ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
ARM: at91: dt: at91sam9g45 family and board device tree files
arm/mx5: add device tree support for imx51 babbage
arm/mx5: add device tree support for imx53 boards
ARM: msm: Add devicetree support for msm8660-surf
msm_serial: Add devicetree support
msm_serial: Use relative resources for iomem
Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro. So they will need <linux/export.h>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The module.h cleanup series is not merged at this point, so use the
older header file for now, to make it build either way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit "ARM: gic: add irq_domain support" (b49b6ff) breaks SPARSE_IRQ
on platforms with GIC. When SPARSE_IRQ is enabled, all NR_IRQS or
mach_desc->nr_irqs will be allocated by arch_probe_nr_irqs(). This caused
irq_alloc_descs to allocate irq_descs after the pre-allocated space.
Make irq_alloc_descs search for an exact irq range and assume it has
been pre-allocated on failure. For DT probing dynamic allocation is used.
DT enabled platforms should set their nr_irqs to NR_IRQ_LEGACY and have all
irq_chips allocate their irq_descs with irq_alloc_descs if SPARSE_IRQ is
enabled.
gic_init irq_start param is changed to be signed with negative meaning do
dynamic Linux irq assigment.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This adds ARM gic interrupt controller initialization using device tree
data.
The initialization function is intended to be called by of_irq_init
function like this:
const static struct of_device_id irq_match[] = {
{ .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
{}
};
static void __init init_irqs(void)
{
of_irq_init(irq_match);
}
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Convert the gic interrupt controller to use irq domains in preparation
for device-tree binding and MULTI_IRQ. This allows for translation between
GIC interrupt IDs and Linux irq numbers.
The meaning of irq_offset has changed. It now is just the number of skipped
GIC interrupt IDs for the controller. It will be 16 for primary GIC and 32
for secondary GICs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
* 'clk' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7131/1: clkdev: Add Common Macro for clk_lookup
clk: spi-pl022: convert to clk_prepare()/clk_unprepare()
clk: timer-sp: convert to clk_prepare()/clk_unprepare()
clk: sa1111: convert to clk_prepare()/clk_unprepare()
clk: mmci: convert to clk_prepare()/clk_unprepare()
clk: amba-pl011: convert to clk_prepare()/clk_unprepare()
clk: amba-pl010: convert to clk_prepare()/clk_unprepare()
clk: amba-clcd: convert to clk_prepare()/clk_unprepare()
clk: amba bus: convert to clk_prepare()/clk_unprepare()
clk: provide prepare/unprepare functions
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
rtmutex: Add missing rcu_read_unlock() in debug_rt_mutex_print_deadlock()
lockdep: Comment all warnings
lib: atomic64: Change the type of local lock to raw_spinlock_t
locking, lib/atomic64: Annotate atomic64_lock::lock as raw
locking, x86, iommu: Annotate qi->q_lock as raw
locking, x86, iommu: Annotate irq_2_ir_lock as raw
locking, x86, iommu: Annotate iommu->register_lock as raw
locking, dma, ipu: Annotate bank_lock as raw
locking, ARM: Annotate low level hw locks as raw
locking, drivers/dca: Annotate dca_lock as raw
locking, powerpc: Annotate uic->lock as raw
locking, x86: mce: Annotate cmci_discover_lock as raw
locking, ACPI: Annotate c3_lock as raw
locking, oprofile: Annotate oprofilefs lock as raw
locking, video: Annotate vga console lock as raw
locking, latencytop: Annotate latency_lock as raw
locking, timer_stats: Annotate table_lock as raw
locking, rwsem: Annotate inner lock as raw
locking, semaphores: Annotate inner lock as raw
locking, sched: Annotate thread_group_cputimer as raw
...
Fix up conflicts in kernel/posix-cpu-timers.c manually: making
cputimer->cputime a raw lock conflicted with the ABBA fix in commit
bcd5cff721 ("cputimer: Cure lock inversion").
This patch remove the hardcoded link between local timers and PPIs,
and convert the PPI users (TWD, MCT and MSM timers) to the new
*_percpu_irq interface. Also some collateral cleanup
(local_timer_ack() is gone, and the interrupt handler is strictly
private to each driver).
PPIs are now useable for more than just the local timers.
Additional testing by David Brown (msm8250 and msm8660) and
Shawn Guo (imx6q).
Cc: David Brown <davidb@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: David Brown <davidb@codeaurora.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
PPI handling is a bit of an odd beast. It uses its own low level
handling code and is hardwired to the local timers (hence lacking
a registration interface).
Instead, switch the low handling to the normal SPI handling code.
PPIs are handled by the handle_percpu_devid_irq flow.
This also allows the removal of some duplicated code.
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: David Brown <davidb@codeaurora.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If two requests have been submitted and one of them is running, if you
call pl330_chan_ctrl(ch_id, PL330_OP_START), there's a window of time
between the spin_lock_irqsave() and the _state() check in which the
running transaction may finish. In that case, we don't receive the
interrupt (because they are disabled), but _start() sees that the DMA
is stopped, so it starts it. The problem is that it sends the
transaction that has just finished again, because pl330_update()
hasn't mark it as done yet.
This patch fixes this race condition by not calling _start() if the
DMA is already executing transactions. When interrupts are reenabled,
pl330_update() will call _start().
Reference: <1317892206-3600-1-git-send-email-javi.merino@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GIC driver must convert logical CPU numbers passed in from Linux
into physical CPU numbers that are understood by the hardware.
This patch uses the new cpu_logical_map macro for performing the
conversion inside the GIC driver.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is unneeded and causes an abort on the SPMP8000 platform.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Zoltan Devai <zoss@devai.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tegra can benefit from the IRQCHIP_MASK_ON_SUSPEND flag, allow it
to be passed to the gic irq chip.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-and-Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
When the cpu is powered down in a low power mode, the gic cpu
interface may be reset, and when the cpu cluster is powered
down, the gic distributor may also be reset.
This patch uses CPU_PM_ENTER and CPU_PM_EXIT notifiers to save
and restore the gic cpu interface registers, and the
CPU_CLUSTER_PM_ENTER and CPU_CLUSTER_PM_EXIT notifiers to save
and restore the gic distributor registers.
Original-author: Gary King <gking@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-and-Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Annotate the low level hardware locks which must not be preempted.
In mainline this change documents the low level nature of
the lock - otherwise there's no functional difference. Lockdep
and Sparse checking will work as usual.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
Lorenzo Pieralisi
Nicolas Pitre
Olof Johansson
Wei Yongjun
Paul Gortmaker
Linus Torvalds
Matt Porter
Lad, Prabhakar
Stephen Boyd
Dave Martin
Rob Herring
Tomasz Figa
Greg Kroah-Hartman
Linus Walleij
Russell King
Will Deacon
Arnd Bergmann
Marek Szyprowski
David Howells
Boojin Kim
Bjorn Helgaas
Myron Stowe
Grant Likely
Javi Merino
Jamie Iles
Marc Zyngier
Zoltan Devai
Colin Cross
Thomas Gleixner