* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
Add #inclusions of linux/tracehook.h to those arch files that had the tracehook
call for TIF_NOTIFY_RESUME added when support for that flag was added to that
arch.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add a keyctl to install a process's session keyring onto its parent. This
replaces the parent's session keyring. Because the COW credential code does
not permit one process to change another process's credentials directly, the
change is deferred until userspace next starts executing again. Normally this
will be after a wait*() syscall.
To support this, three new security hooks have been provided:
cred_alloc_blank() to allocate unset security creds, cred_transfer() to fill in
the blank security creds and key_session_to_parent() - which asks the LSM if
the process may replace its parent's session keyring.
The replacement may only happen if the process has the same ownership details
as its parent, and the process has LINK permission on the session keyring, and
the session keyring is owned by the process, and the LSM permits it.
Note that this requires alteration to each architecture's notify_resume path.
This has been done for all arches barring blackfin, m68k* and xtensa, all of
which need assembly alteration to support TIF_NOTIFY_RESUME. This allows the
replacement to be performed at the point the parent process resumes userspace
execution.
This allows the userspace AFS pioctl emulation to fully emulate newpag() and
the VIOCSETTOK and VIOCSETTOK2 pioctls, all of which require the ability to
alter the parent process's PAG membership. However, since kAFS doesn't use
PAGs per se, but rather dumps the keys into the session keyring, the session
keyring of the parent must be replaced if, for example, VIOCSETTOK is passed
the newpag flag.
This can be tested with the following program:
#include <stdio.h>
#include <stdlib.h>
#include <keyutils.h>
#define KEYCTL_SESSION_TO_PARENT 18
#define OSERROR(X, S) do { if ((long)(X) == -1) { perror(S); exit(1); } } while(0)
int main(int argc, char **argv)
{
key_serial_t keyring, key;
long ret;
keyring = keyctl_join_session_keyring(argv[1]);
OSERROR(keyring, "keyctl_join_session_keyring");
key = add_key("user", "a", "b", 1, keyring);
OSERROR(key, "add_key");
ret = keyctl(KEYCTL_SESSION_TO_PARENT);
OSERROR(ret, "KEYCTL_SESSION_TO_PARENT");
return 0;
}
Compiled and linked with -lkeyutils, you should see something like:
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: _ses
355907932 --alswrv 4043 -1 \_ keyring: _uid.4043
[dhowells@andromeda ~]$ /tmp/newpag
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: _ses
1055658746 --alswrv 4043 4043 \_ user: a
[dhowells@andromeda ~]$ /tmp/newpag hello
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: hello
340417692 --alswrv 4043 4043 \_ user: a
Where the test program creates a new session keyring, sticks a user key named
'a' into it and then installs it on its parent.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Implement TIF_NOTIFY_RESUME for most of those architectures in which isn't yet
available, and, whilst we're at it, have it call the appropriate tracehook.
After this patch, blackfin, m68k* and xtensa still lack support and need
alteration of assembly code to make it work.
Resume notification can then be used (by a later patch) to install a new
session keyring on the parent of a process.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
cc: linux-arch@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
These changes were a direct result of using a semantic patch
More information can be found at http://www.emn.fr/x-info/coccinelle/
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Convert CRIS to use asm-generic/hardirq.h
Also remove unneeded (incorrect) prototypes for setup_irq().
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
On CRIS, the high address bit controls caching, which means that
we can add a pgprot_noncached() macro that sets this bit in the
address.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Conflicts:
arch/sparc/kernel/smp_64.c
arch/x86/kernel/cpu/perf_counter.c
arch/x86/kernel/setup_percpu.c
drivers/cpufreq/cpufreq_ondemand.c
mm/percpu.c
Conflicts in core and arch percpu codes are mostly from commit
ed78e1e078dd44249f88b1dd8c76dafb39567161 which substituted many
num_possible_cpus() with nr_cpu_ids. As for-next branch has moved all
the first chunk allocators into mm/percpu.c, the changes are moved
from arch code to mm/percpu.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
This sockopt goes in line with SO_TYPE and SO_PROTOCOL. It makes it
possible for userspace programs to pass around file descriptors — I
am referring to arguments-to-functions, but it may even work for the
fd passing over UNIX sockets — without needing to also pass the
auxiliary information (PF_INET6/IPPROTO_TCP).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to SO_TYPE returning the socket type, SO_PROTOCOL allows to
retrieve the protocol used with a given socket.
I am not quite sure why we have that-many copies of socket.h, and why
the values are not the same on all arches either, but for where hex
numbers dominate, I use 0x1029 for SO_PROTOCOL as that seems to be
the next free unused number across a bunch of operating systems, or
so Google results make me want to believe. SO_PROTOCOL for others
just uses the next free Linux number, 38.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Discarded sections in different archs share some commonality but have
considerable differences. This led to linker script for each arch
implementing its own /DISCARD/ definition, which makes maintaining
tedious and adding new entries error-prone.
This patch makes all linker scripts to move discard definitions to the
end of the linker script and use the common DISCARDS macro. As ld
uses the first matching section definition, archs can include default
discarded sections by including them earlier in the linker script.
ia64 is notable because it first throws away some ia64 specific
subsections and then include the rest of the sections into the final
image, so those sections must be discarded before the inclusion.
defconfig compile tested for x86, x86-64, powerpc, powerpc64, ia64,
alpha, sparc, sparc64 and s390. Michal Simek tested microblaze.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Cc: linux-arch@vger.kernel.org
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Tony Luck <tony.luck@intel.com>
Pull linus#master to merge PER_CPU_DEF_ATTRIBUTES and alpha build fix
changes. As alpha in percpu tree uses 'weak' attribute instead of
inline assembly, there's no need for __used attribute.
Conflicts:
arch/alpha/include/asm/percpu.h
arch/mn10300/kernel/vmlinux.lds.S
include/linux/percpu-defs.h
The DEFINE_PER_CPU of current_pgd was on CRIS defined using volatile,
which is not needed. Remove volatile.
Tested on an ARTPEC-3 (CRISv32) board.
tj: extern DEFINE_PER_CPU() replaced with DECLARE_PER_CPU()
[ Impact: code cleanup ]
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
x86 throws away .discard section but no other archs do. Also,
.discard is not thrown away while linking modules. Make every arch
and module linking throw it away. This will be used to define dummy
variables for percpu declarations and definitions.
This patch is based on Ivan Kokshaysky's alpha percpu patch.
[ Impact: always throw away everything in .discard ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Since dmanr is unsigned, negatives are wrapped and caught by the other test.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert most arches to use asm-generic/kmap_types.h.
Move the KM_FENCE_ macro additions into asm-generic/kmap_types.h,
controlled by __WITH_KM_FENCE from each arch's kmap_types.h file.
Would be nice to be able to add custom KM_types per arch, but I don't yet
see a nice, clean way to do that.
Built on x86_64, i386, mips, sparc, alpha(tonyb), powerpc(tonyb), and
68k(tonyb).
Note: avr32 should be able to remove KM_PTE2 (since it's not used) and
then just use the generic kmap_types.h file. Get avr32 maintainer
approval.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* create mm/init-mm.c, move init_mm there
* remove INIT_MM, initialize init_mm with C99 initializer
* unexport init_mm on all arches:
init_mm is already unexported on x86.
One strange place is some OMAP driver (drivers/video/omap/) which
won't build modular, but it's already wants get_vm_area() export.
Somebody should look there.
[akpm@linux-foundation.org: add missing #includes]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Everyone cut and paste this comment from my original one. We now do
it generically, so cut the comments.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Amerigo Wang <amwang@redhat.com>
The current asm-generic/page.h only contains the get_order
function, and asm-generic/uaccess.h only implements
unaligned accesses. This renames the file to getorder.h
and uaccess-unaligned.h to make room for new page.h
and uaccess.h file that will be usable by all simple
(e.g. nommu) architectures.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic/atomic.h only defines the
atomic_long type. This renames it to atomic-long.h
so we have a place to add a truly generic atomic.h
that can be used on all non-SMP systems.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
This provides a reliable way for asm-generic/types.h and other
files to find out if it is running on a 32 or 64 bit platform.
We cannot use CONFIG_64BIT for this in headers that are included
from user space because CONFIG symbols are not available there.
We also cannot do it inside of asm/types.h because some headers
need the word size but cannot include types.h.
The solution is to introduce a new header <asm/bitsperlong.h>
that defines both __BITS_PER_LONG for user space and
BITS_PER_LONG for usage in the kernel. The asm-generic
version falls back to 32 bit unless the architecture overrides
it, which I did for all 64 bit platforms.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The existing asm-generic versions are incomplete and included
by some architectures. New architectures should be able
to use a generic version, so rename the existing files and
change all users, which lets us add the new files.
Signed-off-by: Remis Lima Baima <remis.developer@googlemail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The end brace for a larger for statement was placed inside the #else
part of #ifdef TIMER_VECT1. However, for all current chips, the
define TIMER_VECT1 is always unset, and the error was never triggered.
Move the brace down below the #endif.
Fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=13476
Reported-by: Martin Ettl <ettl.martin@gmx.de>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <mikael.starvik@axis.com>
The code didn't test the pointer to the newly allocated
memory, but a parameter sent in as value.
Since the input parameter was most often set, the code
would have used a null pointer if the kmalloc failed.
If the input parameter was not set, the code would
leak the allocated buffer.
http://bugzilla.kernel.org/show_bug.cgi?id=11363
Reported-by: Daniel Marjamäki <danielm77@spray.se>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Add an optimized strcmp for CRISv32. This improves strcmp performance
with about 25% when comparing a 55 character string with itself.
Signed-off-by: Edgar Iglesias <edgar@axis.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Somehow, the assignments of rw->lock got written as comparisons.
The effect probably was that the read-write spinlocks never locked.
However, since the locks are only used in CONFIG_SMP and SMP CRIS is
experimental, it has never been identified as a problem.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Conflicts:
arch/mips/sibyte/bcm1480/irq.c
arch/mips/sibyte/sb1250/irq.c
Merge reason: we gathered a few conflicts plus update to latest upstream fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/cris/arch-v32/drivers/mach-a3/gpio.c:
+spin_lock_irqrestore(&gpio_lock, flags);
arch/cris/arch-v32/drivers/mach-a3/gpio.c:
+spin_lock_irqrestore(&gpio_lock, flags);
should that not be "spin_unlock_irqrestore()"?
The code in question was inside an (most often) undefined ifdef.
Reported-by: "Robert P. J. Day" <rpjday@crashcourse.ca>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
according to Ingo, change set_affinity() in irq_chip should return int,
because that way we can handle failure cases in a much cleaner way, in
the genirq layer.
v2: fix two typos
[ Impact: extend API ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-arch@vger.kernel.org
LKML-Reference: <49F654E9.4070809@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Sun, Apr 19, 2009 at 10:01:50PM +0200, Robert P. J. Day wrote:
> ./arch/cris/arch-v32/kernel/Makefile:obj-$(CONFIG_ETRAXFS_SIM) += vcs_hook.o
>
> there appears to be no definition of ETRAXFS_SIM anywhere.
There hasn't been a vcs_hook.c file here for ages.
Remove the line from the Makefile.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reported-by: "Robert P. J. Day" <rpjday@crashcourse.ca>
Merge the machine dependent boot directories for v10 and v32.
This avoids some code duplication and eases the way for further
merging later on.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Use the new general RS485 Linux data structure (introduced by Alan with
commit number c26c56c0f4) in the Cris
architecture too (currently, Cris still uses the old private data
structure instead of the new one).
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Tested-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Tested-by: Janez Cufer <janez.cufer@cetrtapot.si>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://repo.or.cz/cris-mirror:
CRISv32: Remove extraneous space between -I and the path.
cris: convert obsolete hw_interrupt_type to struct irq_chip
BUG to BUG_ON changes
cpumask: use mm_cpumask() wrapper: cris
cpumask: Use accessors code.: cris
cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits.: cris
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (413 commits)
tracing, net: fix net tree and tracing tree merge interaction
tracing, powerpc: fix powerpc tree and tracing tree interaction
ring-buffer: do not remove reader page from list on ring buffer free
function-graph: allow unregistering twice
trace: make argument 'mem' of trace_seq_putmem() const
tracing: add missing 'extern' keywords to trace_output.h
tracing: provide trace_seq_reserve()
blktrace: print out BLK_TN_MESSAGE properly
blktrace: extract duplidate code
blktrace: fix memory leak when freeing struct blk_io_trace
blktrace: fix blk_probes_ref chaos
blktrace: make classic output more classic
blktrace: fix off-by-one bug
blktrace: fix the original blktrace
blktrace: fix a race when creating blk_tree_root in debugfs
blktrace: fix timestamp in binary output
tracing, Text Edit Lock: cleanup
tracing: filter fix for TRACE_EVENT_FORMAT events
ftrace: Using FTRACE_WARN_ON() to check "freed record" in ftrace_release()
x86: kretprobe-booster interrupt emulation code fix
...
Fix up trivial conflicts in
arch/parisc/include/asm/ftrace.h
include/linux/memory.h
kernel/extable.c
kernel/module.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
Remove two unneeded exports and make two symbols static in fs/mpage.c
Cleanup after commit 585d3bc06f
Trim includes of fdtable.h
Don't crap into descriptor table in binfmt_som
Trim includes in binfmt_elf
Don't mess with descriptor table in load_elf_binary()
Get rid of indirect include of fs_struct.h
New helper - current_umask()
check_unsafe_exec() doesn't care about signal handlers sharing
New locking/refcounting for fs_struct
Take fs_struct handling to new file (fs/fs_struct.c)
Get rid of bumping fs_struct refcount in pivot_root(2)
Kill unsharing fs_struct in __set_personality()
Pass the original flags to rwlock arch-code, so that it can re-enable
interrupts if implemented for that architecture.
Initially, make __raw_read_lock_flags and __raw_write_lock_flags stubs
which just do the same thing as non-flags variants.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: cleanup
Convert the last remaining users to struct irq_chip.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
CC: Mikael Starvik <starvik@axis.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Don't pull it in sched.h; very few files actually need it and those
can include directly. sched.h itself only needs forward declaration
of struct fs_struct;
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Impact: cleanup
It's unused, since about 1995. So remove all initialization of it in
preparation for actually removing the field.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
* 'irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (32 commits)
x86: disable __do_IRQ support
sparseirq, powerpc/cell: fix unused variable warning in interrupt.c
genirq: deprecate obsolete typedefs and defines
genirq: deprecate __do_IRQ
genirq: add doc to struct irqaction
genirq: use kzalloc instead of explicit zero initialization
genirq: make irqreturn_t an enum
genirq: remove redundant if condition
genirq: remove unused hw_irq_controller typedef
irq: export remove_irq() and setup_irq() symbols
irq: match remove_irq() args with setup_irq()
irq: add remove_irq() for freeing of setup_irq() irqs
genirq: assert that irq handlers are indeed running in hardirq context
irq: name 'p' variables a bit better
irq: further clean up the free_irq() code flow
irq: refactor and clean up the free_irq() code flow
irq: clean up manage.c
irq: use GFP_KERNEL for action allocation in request_irq()
kernel/irq: fix sparse warning: make symbol static
irq: optimize init_kstat_irqs/init_copy_kstat_irqs
...
Makes code futureproof against the impending change to mm->cpu_vm_mask.
It's also a chance to use the new cpumask_ ops which take a pointer
(the older ones are deprecated, but there's no hurry for arch code).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Impact: use new API
Use the accessors rather than frobbing bits directly. Most of this is
in arch code I haven't even compiled, but is straightforward.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: cleanup, futureproof
In fact, all cpumask ops will only be valid (in general) for bit
numbers < nr_cpu_ids. So use that instead of NR_CPUS in various
places.
This is always safe: no cpu number can be >= nr_cpu_ids, and
nr_cpu_ids is initialized to NR_CPUS at boot.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
The current definition of CALLER_ADDRx isn't suitable for all platforms.
E.g. for ARM __builtin_return_address(N) doesn't work for N > 0 and
AFAIK for powerpc there are no frame pointers needed to have a working
__builtin_return_address. This patch allows defining the CALLER_ADDRx
macros in <asm/ftrace.h> and let these take precedence.
Because now <asm/ftrace.h> is included unconditionally in
<linux/ftrace.h> all archs that don't already had this include get an
empty one for free.
Signed-off-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
User space can request hardware and/or software time stamping.
Reporting of the result(s) via a new control message is enabled
separately for each field in the message because some of the
fields may require additional computation and thus cause overhead.
User space can tell the different kinds of time stamps apart
and choose what suits its needs.
When a TX timestamp operation is requested, the TX skb will be cloned
and the clone will be time stamped (in hardware or software) and added
to the socket error queue of the skb, if the skb has a socket
associated with it.
The actual TX timestamp will reach userspace as a RX timestamp on the
cloned packet. If timestamping is requested and no timestamping is
done in the device driver (potentially this may use hardware
timestamping), it will be done in software after the device's
start_hard_xmit routine.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'syscalls' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (44 commits)
[CVE-2009-0029] s390 specific system call wrappers
[CVE-2009-0029] System call wrappers part 33
[CVE-2009-0029] System call wrappers part 32
[CVE-2009-0029] System call wrappers part 31
[CVE-2009-0029] System call wrappers part 30
[CVE-2009-0029] System call wrappers part 29
[CVE-2009-0029] System call wrappers part 28
[CVE-2009-0029] System call wrappers part 27
[CVE-2009-0029] System call wrappers part 26
[CVE-2009-0029] System call wrappers part 25
[CVE-2009-0029] System call wrappers part 24
[CVE-2009-0029] System call wrappers part 23
[CVE-2009-0029] System call wrappers part 22
[CVE-2009-0029] System call wrappers part 21
[CVE-2009-0029] System call wrappers part 20
[CVE-2009-0029] System call wrappers part 19
[CVE-2009-0029] System call wrappers part 18
[CVE-2009-0029] System call wrappers part 17
[CVE-2009-0029] System call wrappers part 16
[CVE-2009-0029] System call wrappers part 15
...
Add swab.h to kbuild.asm and remove the individual entries from
each arch, mark as unifdef as some arches have some kernel-only
bits inside.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adjust the arch overrides to the new names as well.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h. Move the type definition
to linux/types.h to break the loop.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new Kconfig option to build "staging" drivers (code in
drivers/staging/) is seen in all except three architectures (arm, h8300,
cris), because in these cases arch/$ARCH/Kconfig does NOT source
drivers/Kconfig.
This patch adds the source "drivers/staging/Kconfig" to
arch/$ARCH/Kconfig for these three exceptional cases.
Signed-off-by: Duncan Haldane <duncan_h@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Impact: cleanup
Each SMP arch defines these themselves. Move them to a central
location.
Twists:
1) Some archs (m32, parisc, s390) set possible_map to all 1, so we add a
CONFIG_INIT_ALL_POSSIBLE for this rather than break them.
2) mips and sparc32 '#define cpu_possible_map phys_cpu_present_map'.
Those archs simply have phys_cpu_present_map replaced everywhere.
3) Alpha defined cpu_possible_map to cpu_present_map; this is tricky
so I just manipulate them both in sync.
4) IA64, cris and m32r have gratuitous 'extern cpumask_t cpu_possible_map'
declarations.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Mike Travis <travis@sgi.com>
Cc: ink@jurassic.park.msu.ru
Cc: rmk@arm.linux.org.uk
Cc: starvik@axis.com
Cc: tony.luck@intel.com
Cc: takata@linux-m32r.org
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: paulus@samba.org
Cc: schwidefsky@de.ibm.com
Cc: lethal@linux-sh.org
Cc: wli@holomorphy.com
Cc: davem@davemloft.net
Cc: jdike@addtoit.com
Cc: mingo@redhat.com
Remove the links to architecture and machine dependent directories
(boot, lib, drivers, arch, mach)
The links were created and used mostly from the arch/cris/Makefile,
so why not dispense with them altogether?
Changed $(ARCH) to "cris" in Makefile, it is easier to read this way.
The CRISv32 head.S common files for the kernel and compressed images
needed to be modified to use ifdefs instead of using the now removed
mach link. Since there are only two versions, this is not a huge loss
in readability.
The link to vmlinux.lds.S is also replaced with a merged version
which uses ifdefs to select the correct layout.
System.map before and after are identical.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Eliminates the link to arch specific asm-offsets.c from CRIS
architecture build system.
Resulting asm-offsets.s are identical before and after change
for both arch-v10 and arch-v32.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: (47 commits)
uwb: wrong sizeof argument in mac address compare
uwb: don't use printk_ratelimit() so often
uwb: use kcalloc where appropriate
uwb: use time_after() when purging stale beacons
uwb: add credits for the original developers of the UWB/WUSB/WLP subsystems
uwb: add entries in the MAINTAINERS file
uwb: depend on EXPERIMENTAL
wusb: wusb-cbaf (CBA driver) sysfs ABI simplification
uwb: document UWB and WUSB sysfs files
uwb: add symlinks in sysfs between radio controllers and PALs
uwb: dont tranmit identification IEs
uwb: i1480/GUWA100U: fix firmware download issues
uwb: i1480: remove MAC/PHY information checking function
uwb: add Intel i1480 HWA to the UWB RC quirk table
uwb: disable command/event filtering for D-Link DUB-1210
uwb: initialize the debug sub-system
uwb: Fix handling IEs with empty IE data in uwb_est_get_size()
wusb: fix bmRequestType for Abort RPipe request
wusb: fix error path for wusb_set_dev_addr()
wusb: add HWA host controller driver
...
Change cris to use the new bcd2bin/bin2bcd functions instead of the
obsolete BCD_TO_BIN/BIN_TO_BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Chris Zankel <zankel@tensilica.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements a new freezer subsystem in the control groups
framework. It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.
The freezer subsystem in the container filesystem defines a file named
freezer.state. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup. Reading will return the current state.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This is the basic mechanism which should do the right thing for user space
task in a simple scenario.
It's important to note that freezing can be incomplete. In that case we
return EBUSY. This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time. After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read. The state will remain
"FREEZING" until one of these things happens:
1) Userspace cancels the freezing operation by writing "RUNNING" to
the freezer.state file
2) Userspace retries the freezing operation by writing "FROZEN" to
the freezer.state file (writing "FREEZING" is not legal
and returns EIO)
3) The tasks that blocked the cgroup from entering the "FROZEN"
state disappear from the cgroup's set of tasks.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As policy->governor is already set to CPUFREQ_DEFAULT_GOVERNOR in the
(always built-in) cpufreq core, we do not need to set it in the drivers.
This fixes the sparc64 allmodconfig build failure.
Also, remove a totally useles setting of ->policy in cpufreq-pxa3xx.c.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the cris defconfigs to arch/cris/configs/ where they
belong.
As a side effect they can now be used directly through e.g.
make ARCH=cris artpec_3_defconfig
The default defconfig is set through KBUILD_DEFCONFIG.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Right now, there is no notifier that is called on a new cpu, before the new
cpu begins processing interrupts/softirqs.
Various kernel function would need that notification, e.g. kvm works around
by calling smp_call_function_single(), rcu polls cpu_online_map.
The patch adds a CPU_STARTING notification. It also adds a helper function
that sends the message to all cpu_chain handlers.
Tested on x86-64.
All other archs are untested. Especially on sparc, I'm not sure if I got
it right.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch also includes the required removal of (unused) inclusion of
<asm/a.out.h> <linux/a.out.h>'s in the arch/ code for these
architectures.
[dwmw2: updated for 2.6.27-rc]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove arch-specific show_mem() in favor of the generic version.
This also removes the following redundant information display:
- free pages, printed by show_free_areas()
- pages in swapcache, printed by show_swap_cache_info()
where show_mem() calls show_free_areas(), which calls
show_swap_cache_info().
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Inflate requires some dynamic memory allocation very early in the boot
process and this is provided with a set of four functions:
malloc/free/gzip_mark/gzip_release.
The old inflate code used a mark/release strategy rather than implement
free. This new version instead keeps a count on the number of outstanding
allocations and when it hits zero, it resets the malloc arena.
This allows removing all the mark and release implementations and unifying
all the malloc/free implementations.
The architecture-dependent code must define two addresses:
- free_mem_ptr, the address of the beginning of the area in which
allocations should be made
- free_mem_end_ptr, the address of the end of the area in which
allocations should be made. If set to 0, then no check is made on
the number of allocations, it just grows as much as needed
The architecture-dependent code can also provide an arch_decomp_wdog()
function call. This function will be called several times during the
decompression process, and allow to notify the watchdog that the system is
still running. If an architecture provides such a call, then it must
define ARCH_HAS_DECOMP_WDOG so that the generic inflate code calls
arch_decomp_wdog().
Work initially done by Matt Mackall, updated to a recent version of the
kernel and improved by me.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
free_area_init_node() gets passed in the node id as well as the node
descriptor. This is redundant as the function can trivially get the node
descriptor itself by means of NODE_DATA() and the node's id.
I checked all the users and NODE_DATA() seems to be usable everywhere
from where this function is called.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://www.jni.nu/cris:
[CRISv10] Clean up compressed/misc.c
[CRISv10] Correct whitespace damage.
[CRIS] Correct definition of subdirs for install_headers.
[CRIS] Correct image makefiles to allow using a separate OBJ-directory.
[CRIS] Build fixes for compressed and rescue images for v10 and v32:
It looks at least odd to apply spin_unlock to a mutex.
cris: compile fixes for 2.6.26-rc5
This makes the CRIS-port directories follow the same naming
convention as the rest of the kernel.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Make compile succeed when building with O= (srctree != objtree).
Signed-off-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
- Use the normal cross gcc instead of using an elf specific cris toolchain.
This removes the dependency of this second toolchain.
- Use the normal cross objcopy instead of overriding it to use elf-toolchain.
This allows compiling using "CROSS_COMPILE=$CRIS_GCC/cris-axis-linux-gnu-"
instead of just "CROSS_COMPILE=$CRIS_GCC/cris-axis-linux-gnu/bin/"
- Remove redundant rules for compiling, the implicit rules are sufficient.
- Convert the arch/cris/arch-v10/boot/compressed/head.S to format
accepted by the cris-axis-linux-gnu-gcc (registers must be prefixed
with '$', remove explicit underscore on exported symbols)
- Remove a number of unused (and duplicated) prototypes from
arch/cris/arch-v10/boot/compressed/misc.c.
- Correct memcpy and memset return values (actually return them!)
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Add dummy ops for serial debug port.
Add setting of c_ispeed/c_ospeed as suggested by Alan Cox.
Signed-off-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
All of the open() functions which don't need the BKL on their face may
still depend on its acquisition to serialize opens against driver
initialization. So make those functions acquire then release the BKL to be
on the safe side.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This documents the fact that somebody looked at the relevant open()
functions and concluded that, due to their trivial nature, no locking was
needed.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The cris implementation of sys_pipe only differs from the generic one
by taking the BKL before calling do_pipe which isn't not nessecary.
Just kill the cris implementation and use the generic one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remember to close the files if copy_to_user() failed.
Spotted by dm.n9107@gmail.com.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Cc: DM <dm.n9107@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create() to make sure that ->proc_fops be setup before gluing PDE to
main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
show_mem() has no need to print the amount of free swap space manually because
show_free_areas() does this already and is called by the former.
The two outputs only differ in text formatting:
printk("Free swap = %lukB\n", ...);
printk("Free swap: %6ldkB\n", ...);
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Function __copy_user_zeroing in arch/lib/usercopy.c had the wrong parameter
set as __user, and in include/asm-cris/uaccess.h, it was not set at all for
some of the calling functions.
This will cut the number of warnings quite dramatically when using sparse.
While we're here, remove useless CVS log and correct confusing typo.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk reported another compile error with a SVN head GCC:
...
CC arch/cris/arch-v10/lib/string.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:138:
error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:138:
error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:139:
error: lvalue required as increment operand
...
This is due to the use of the construct:
*((long*)dst)++ = lc;
Which isn't legal since casts don't return an lvalue.
The solution is to import the implementation from newlib,
which is continually autotested together with GCC mainline,
and uses the construct:
*(long *) dst = lc; dst += 4;
Since this is an import of a file from newlib, I'm not touching
the formatting or correcting any checkpatch errors.
As for the earlier fix for memset.c, even if the two files for
CRIS v10 and CRIS v32 are identical at the moment, it might
be possible to tweak the CRIS v32 version.
Thus, I'm not yet folding them into the same file, at least not
until we've done some research on it.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2f569afd9c
(CONFIG_HIGHPTE vs. sub-page page tables) introduced use of
inc_zone_page_state and dec_zone_page_state in include/linux/mm.h.
Those are defined in include/linux/vmstat.h, but after it includes
mm.h, making it impossible to include vmstat.h since inc_zone_page_state
and dec_zone_page_state then would be undefined.
arch/cris/arch-v10/kernel/time.c does just this, which makes the
CRIS v10 build break with the following error:
...
CC arch/cris/arch-v10/kernel/time.o
In file included from include/linux/vmstat.h:7,
from arch/cris/arch-v10/kernel/time.c:17:
include/linux/mm.h: In function 'pgtable_page_ctor':
include/linux/mm.h:902: error: implicit declaration of function 'inc_zone_page_state'
include/linux/mm.h: In function 'pgtable_page_dtor':
include/linux/mm.h:908: error: implicit declaration of function 'dec_zone_page_state'
make[2]: *** [arch/cris/arch-v10/kernel/time.o] Error 1
make[1]: *** [arch/cris/arch-v10/kernel] Error 2
make: *** [sub-make] Error 2
...
By changing kernel/time.c to include linux/mm.h, the build succeeds.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk reported the following compile error with a SVN head GCC:
...
CC arch/cris/arch-v10/lib/memset.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/memset.c: In function 'memset':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/memset.c:164: error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/memset.c:165: error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/memset.c:166: error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/memset.c:167: error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/memset.c:185: error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/memset.c:189: error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/memset.c:192: error: lvalue required as increment operand
... etc ...
This is due to the use of the construct:
*((long*)dst)++ = lc;
Which is no longer legal since casts don't return an lvalue.
The solution is to import the implementation from newlib,
which is continually autotested together with GCC mainline,
and uses the construct:
*(long *) dst = lc; dst += 4;
With this change, the generated code actually shrinks 76 bytes
since gcc notices that it can use autoincrement for the move
instruction in CRIS.
text data bss dec hex filename
304 0 0 304 130 memset.old.o
text data bss dec hex filename
228 0 0 228 e4 memset.o
Since this is an import of a file from newlib, I'm not touching
the formatting or correcting any checkpatch errors.
Note also that even if the two files for the CRIS v10 and CRIS v32
are identical at the moment, it might be possible to tweak the
CRIS v32 version. Thus, I'm not yet folding them into the same file,
at least not until we've done some research on it.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'cris' of git://www.jni.nu/cris: (158 commits)
CRIS v32: Remove hwregs/timer_defs.h, it is now architecture specific.
CRIS v32: Change drivers/i2c.c locking.
CRIS v32: Rewrite ARTPEC-3 gpio driver to avoid volatiles and general cleanup.
CRIS: Add new timerfd syscall entries.
MAINTAINERS: Add my information for the CRIS port.
CRIS v32: Correct spelling of bandwidth in function name.
CRIS v32: Clean up nandflash.c for ARTPEC-3 and ETRAX FS.
CRIS v10: Cleanup of drivers/gpio.c
CRIS v10: drivers/net/cris/eth_v10.c rename LED defines to CRIS_LED to avoid name clash.
CRIS: Make io_pwm_set_period members unsigned in etraxgpio.h
CRIS: Move ETRAX_AXISFLASHMAP to common Kconfig file.
CRIS: Drop regs parameter from call to profile_tick in kernel/time.c
CRIS v32: Fix minor formatting issue in mach-a3/io.c
CRIS v32: Initialize GIO even if we're rambooting in kernel/head.S
CRIS v32: Remove kernel/arbiter.c, it now exists in machine dependent directory.
CRIS v32: Minor changes to avoid errors in asm-cris/arch-v32/hwregs/reg_rdwr.h
CRIS v32: arch-v32/hwregs/intr_vect_defs.h moved to machine dependent directory.
CRIS v32: Correct offset for TASK_pid in asm-cris/arch-v32/offset.h
CRIS v32: Move register map header to machine dependent directory.
CRIS v32: Let compiler know that memory is clobbered after a break op.
...
When the conversion factor between jiffies and milli- or microseconds is
not a single multiply or divide, as for the case of HZ == 300, we currently
do a multiply followed by a divide. The intervening result, however, is
subject to overflows, especially since the fraction is not simplified (for
HZ == 300, we multiply by 300 and divide by 1000).
This is exposed to the user when passing a large timeout to poll(), for
example.
This patch replaces the multiply-divide with a reciprocal multiplication on
32-bit platforms. When the input is an unsigned long, there is no portable
way to do this on 64-bit platforms there is no portable way to do this
since it requires a 128-bit intermediate result (which gcc does support on
64-bit platforms but may generate libgcc calls, e.g. on 64-bit s390), but
since the output is a 32-bit integer in the cases affected, just simplify
the multiply-divide (*3/10 instead of *300/1000).
The reciprocal multiply used can have off-by-one errors in the upper half
of the valid output range. This could be avoided at the expense of having
to deal with a potential 65-bit intermediate result. Since the intent is
to avoid overflow problems and most of the other time conversions are only
semiexact, the off-by-one errors were considered an acceptable tradeoff.
At Ralf Baechle's suggestion, this version uses a Perl script to compute
the necessary constants. We already have dependencies on Perl for kernel
compiles. This does, however, require the Perl module Math::BigInt, which
is included in the standard Perl distribution starting with version 5.8.0.
In order to support older versions of Perl, include a table of canned
constants in the script itself, and structure the script so that
Math::BigInt isn't required if pulling values from said table.
Running the script requires that the HZ value is available from the
Makefile. Thus, this patch also adds the Kconfig variable CONFIG_HZ to the
architectures which didn't already have it (alpha, cris, frv, h8300, m32r,
m68k, m68knommu, sparc, v850, and xtensa.) It does *not* touch the sh or
sh64 architectures, since Paul Mundt has dealt with those separately in the
sh tree.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Ralf Baechle <ralf@linux-mips.org>,
Cc: Sam Ravnborg <sam@ravnborg.org>,
Cc: Paul Mundt <lethal@linux-sh.org>,
Cc: Richard Henderson <rth@twiddle.net>,
Cc: Michael Starvik <starvik@axis.com>,
Cc: David Howells <dhowells@redhat.com>,
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>,
Cc: Hirokazu Takata <takata@linux-m32r.org>,
Cc: Geert Uytterhoeven <geert@linux-m68k.org>,
Cc: Roman Zippel <zippel@linux-m68k.org>,
Cc: William L. Irwin <sparclinux@vger.kernel.org>,
Cc: Chris Zankel <chris@zankel.net>,
Cc: H. Peter Anvin <hpa@zytor.com>,
Cc: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Change spin_lock + local_irq_save into spin_lock_irqsave
- Change spin_unlock + local_irq_restore into spin_unlock_irqrestore
- Return ENOTTY if ioctl is not recognized as a cris ioctl.
- Make init functions static.
Changes as suggested by Andrew Morton, plus general cleanup to
ease later consolidation of driver into machine common driver.
- Correct parameter type of gpio_write to const char __user *
- Remove volatile from the arrays of machine dependent registers, use
readl and writel to access them instead.
- Remove useless casts of void.
- Use spin_lock_irqsave for locking.
- Break gpio_write into smaller sub-functions.
- Remove useless breaks after returns.
- Don't perform any change in IO_CFG_WRITE_MODE if values are invalid.
(previously values were set and then set to zero)
- Change cast for copy_to_user to (void __user *)
- Make file_operations gpio_fops static and const.
- Make setget_output static. (However, it's still inline since the CRIS
architecture is still not SMP, which makes the function small enough
to inline)
Clean up issues noticed by Andrew Morton:
- Use a combined struct for allocating the mtd_info and nand_chip structs
instead of using anonymous memory as the example in
Documentation/DocBook/mtdnand.tmpl
- Use kzalloc instead of using kmalloc/memset(0)
- Make crisv32_device_ready static.
- Change parameters of gpio_write (const char * buf -> const char __user *buf)
- Don't initialize static variables to zero.
- Remove useless casts from void.
- Change name of interrupt routine (gpio_pa_interrupt -> gpio_interrupt)
- Use kzmalloc instead of allocating memory and zeroing it manually.
- Correct casts for copy_to_user and copy_from_user to (void __user *)
- Make file_operations gpio_fops static.
- Make ioif_watcher static, not used outside this file.
- Move alignment of init data to page size outside define CONFIG_BLK_DEV_INITRD
This avoids oops due to memory on the same page as init data being freed.
- Change hardcoded page size to use macro from asm/page.h
- Add reserved memory via CONFIG_ETRAX_VMEM_SIZE.
- Use available defines for TEXT_TEXT and INITCALLS.
- Cleanup whitespace.
- Slight tweaks, use $acr + addoq to propagate carry across the loop boundary.
- Better use of latency cycles.
- Remove duplicate folding of carry, it is not needed.
- Change include paths to machine specific headers (asm/arch/hwregs -> hwregs)
- Add cpu_possible_map as cpumask_t and export it.
- Drop struct pt_regs parameter from crisv32_ipi_interrupt.
- timer -> timer0
- do_signal now returns void, and does not have the previous signal set
as a parameter.
- Remove sys_rt_sigsuspend, we can use the common one instead.
- Change sys_sigsuspend to be more like x86, don't call do_signal here.
- handle_signal, setup_frame and setup_rt_frame now return -EFAULT
if we've delivered a segfault, which is used by callers to perform
necessary cleanup.
- Break long lines, correct whitespace and formatting errors.
- Change all spin_lock/local_irq_save to spin_lock_irqsave.
- Change multiple returns in functions where we have a lock to goto out.
- Correct number of arguments to gpio_poll_timer_interrupt, gpio_pa_interrupt.
- Break out gpio_write logic to smaller functions to make it readable.
- In setget_input and setget_output, avoid extra if-indent level.
- Change name LED_* -> CRIS_LED_* to avoid name clash.
- Don't use braces around single statement ifs.
- Fix whitespace errors.
- Remove useless CVS id and log.
- Don't use SANITYCHECK(x) as a macro, test FAST_TIMER_SANITY_CHECKS with
ifdef. This makes it possible for automatic indent etc to work.
- Correct some whitespace errors.
- Don't initialize static variable.
- Include pinmux.h from machine specific directory.
- Add some more symbols: crisv32_pinmux_alloc, crisv32_pinmux_dealloc_fixed,
crisv32_io_get_name and crisv32_io_get
- Moved all calls to register_chrdev to a function called by module_init.
- Added mutex locking.
- Added better error handling at start up.
- Added BIN_TO_BCD of the month value before it is saved to the RTC.
- Corrected the month value returned by pcf8563_readreg.
- Cache the voltage low value at driver init so the battery status
information does not get 'accidentally' cleared when setting the RTC time.
- Removed obsolete CONFIG_ETRAX_RTC_READONLY
- Voltage low ioctl():s RTC_VLOW_RD -> RTC_VL_READ, RTC_VLOW_SET -> RTC_VL_CLR
Fixed a bug where two interfaces using pins in the same pin group could
not be allocated at the same time even if there where no pin collisions.
Change all restore and returns into goto exit pattern.
Also, remove useless CVS id and correct chapter reference for ETRAX100LX
Designer's Reference in comment.
If serial port 2 is used, select it in R_GEN_CONFIG.
If serial port 2 is used, setup the control registers for the port.
This is done to avoid a pulse on the TXD line during start up,
which could disturb some units.
Also, remove useless CVS id and log.
- Move local_irq_save to after possible return in console_write_direct.
- Remove old raw_printk hack, not needed anymore.
- Add watchdog handling.
- Make serial_driver use depend on CONFIG_ETRAX_SERIAL.
- Remove useless CVS log.
- Use mutex instead of spinlock, fixes kernel bugzilla report 8339.
- Make sure that pcf8563_init can be called multiple times but only setup once.
- Change RTC_VLOW_RD -> RTC_VL_READ, RTC_VLOW_SET -> RTC_VL_CLR
- Cache the voltage low value at driver init so the battery status
information does not get 'accidentally' cleared when setting the RTC time.
- Add weekday handling.
- Correct leapyear handling to include 100 and 400 year exceptions.
- Correct whitespace and formatting errors.
- Remove useless CVS id tag.
- Set the variable first to zero after first setup, so we can
stop multiple calls to i2c_init from trying to setup i2c.
- The last byte read by the master in an i2c transfer needs to
be NACKed, not ACKed.
- Also, remove useless CVS log and CVS id tags.
- Correct include path for sv_addr_ag.h, should be included from asm/arch/
- Remove useless CVS id tag.
- Correct whitespace errors and some formatting.
- Shorten include paths to machine dependent header files.
- Register name for first timer is now regi_timer0.
- Remove raw_printk hack, use oops_in_progress instead.
- Add handling of CPU frequency scaling for CRIS.
- Remove regs parameter to timer_interrupt, get them from get_irq_regs instead.
- Whitespace and formatting changes.
- Remove watchdog handling, handled elsewhere.
- Shorten include paths to machine dependent header files.
- Remove raw_printk hack, we now use oops_in_progress instead.
- Add handling of BUG for exception handlers (break 14).
- Formatting and whitespace changes.
- Shorten include paths for machine dependent header files.
- Remove unused extern declaration of etrax_gpio_wake_up_check.
- Register name for first timer is now regi_timer0.
- First timer register has changed name to timer0.
- Build IRQs with only IRQ number, mask bit will be calculated instead.
- Add more IRQs, up to 64 supported.
- Use arrays to hold which IRQs triggered instead of trying to do magic
with two 32 bit values now that more than 32 IRQs are supported.
- Shorten include paths for machine specific header files.
- Add magic for booting NAND flash.
- Change CONFIG_ETRAXFS_SIM to CONFIG_ETRAX_VCS_SIM.
- Use assembler macros for initializing hardware (clocks)
- Add stubs for SMP slave CPUs.
- Search for cramfs or jffs2 if no romfs found.
- Initialize l2cache.
- Change include path to machine dependent header files.
- Remove __INLINE__, it expands to inline anyway.
- Don't initialize static variables.
- Change timers to use fasttimer_t instead of timevals.
- Change name of timeval_cmp to fasttime_cmp to highlight this.
- Register name for first timer is regi_timer0, not regi_timer.
- Whitespace and formatting changes.
- Don't return if we're blocking interrupts, goto done and restore interrupts.
- Disable interrupts while walking the fasttimer list, only restore
while doing the callback.
- Remove #ifdef DECLARE_WAITQUEUE, this code won't be used in another OS.
- Remove CVS log.
- Shorten include paths to machine dependent headers.
- Add support for fifth serial port.
- Remove CONFIG_ETRAXFS_SIM and CONFIG_ETRAX_DEBUG_PORT_NULL, no longer used.
- Remove raw_printk and stupid_debug hack, no longer needed.
- Remove dummy console stuff, no longer needed.
- Correct some register type names.
- Correct some whitespace errors and formatting.
- Add ifdef for ETRAX_AXISFLASHMAP to avoid compiling file unless it is set.
- Use assembler macros for setting up clocks.
- Don't copy image, just jump to it (only works for NOR flash)
- Shorten include paths to machine specific headers.
- Remove fill_inbuf, not defined here.
- Return __dest as value from memcpy.
- Enable serial port hardware transmitter and receiver in serial_setup.
- Correct baudrate divisor calculation, changed from 4800 to 115200.
- Add support for Artpec-3 specific serial port setup.
- Initialize pinmux for the correct serial port.
- Fixes for NAND and NOR flash booting.
- Use assembler macros for common tasks (clocks, general io etc)
- Use (EtraxFS or Artpec-3) machine specific include for dram and hardware init.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use EXTRA_CFLAGS instead of CFLAGS.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use KBUILD_CFLAGS instead of CFLAGS.
- Remove raw_prink hack, use oops_in_progress instead.
- When ETRAX_WATCHDOG_NICE_DOGGY is set, loop in trap after oops dump
instead of rebooting.
- Break long lines to less than 80 chars.
- Fix whitespace errors.
- Remove unnecessary comments.
- Add config to use mtd0 as whole flash device.
- Fix whitespace errors.
- Remove braces around single statement ifs.
- Break long lines.
- Remove unnecessary CVS log.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
Removes a lot of cruft.
- Use EXTRA_CFLAGS instead of CFLAGS.
- Remove old specific targets, use more generic ones instead.
- Use if_changed to avoid creating new images when no change.
- Use EXTRA_CFLAGS instead of CFLAGS.
- Remove old and non-generic targets, use generic ones instead.
- Add sub-arch as mach-fs or mach-a3 for EtraxFS and Artpec-3 respectively.
- Add links to sub-arch directories, and erase before trying to create them.
- Include from sub-arch specific include directory "mach".
- Add files to be cleaned in CLEAN_FILES instead of as archclean target.
- Use default partition table when no partition is found (for initial tests)
- Add config ETRAX_AXISFLASHMAP_MTD0WHOLE to allow whole flash as mtd0.
- Add config for VCS simulator connection.
- Add i2c_write and i2c_read as functions.
- Use spinlocks for critical regions.
- Add config item to set I2C data and clock port.
- Put unneeded testcode inside #if 0.
- Remove CVS id tag.
- Remove CRISv32 common arbiter, dma, io and pinmux files,
they are now defined in machine dependent directories.
- Add cache and cacheflush files for working around cache problems
in CRISv32 chips.
- Collect extern declarations at top of file.
- Change raw_printk to printk, use oops_in_progress instead.
- Fix formatting and whitespace.
- Allow the watchdog to be disabled during oops.
- Only disallow oops if we're in_interrupt context (was in_atomic before)
- Use the generic oops_in_progress instead of the raw_printk hack.
- Fix whitespace/formatting.
- Remove CVS log entries.
The header files describe the hardware registers available in both
these chips, note that most of this documentation is automatically
generated from the hardware implementation.
The two chips are somewhat different, and needs different handling.
Adds handing of the dma, dram initialization, hardware settings, io,
memory arbiter and pinmux
Also moves the dma, dram initialization and io from CRIS v32 common files.
Linus Torvalds
David Howells
Stoyan Gaydarov
Christoph Hellwig
Arnd Bergmann
Tejun Heo
David S. Miller
Jan Engelhardt
Benjamin Herrenschmidt
Alexey Dobriyan
Peter Zijlstra
Jesper Nilsson
Roel Kluin
Randy Dunlap
Rusty Russell
Roel Kluin
Ingo Molnar
Yinghai Lu
Claudio Scordino
Robin Holt
Thomas Gleixner
Stoyan Gaydarov
Al Viro
Matt LaPlante
Uwe Kleine-Koenig
Patrick Ohly
Harvey Harrison
Heiko Carstens
Matthew Wilcox
F. Duncan M. Haldane
Kay Sievers
Frederik Schwarzer
Adrian Bunk
Matt Helsley
David Vrabel
Dominik Brodowski
David Woodhouse
Greg Kroah-Hartman
Manfred Spraul
Johannes Weiner
Thomas Petazzoni
Akinobu Mita
Dmitry Baryshkov
Jonathan Corbet
Jesper Nilsson
Julia Lawall
Hinko Kocevar
Jens Axboe
Ulrich Drepper
Denis V. Lunev
Sam Ravnborg
Linus Torvalds
H. Peter Anvin
Jan Engelhardt
Jesper Nilsson