This driver manages CoreSight TPIU (Trace Port Interface Unit)
which acts as a sink. TPIU is typically connected to some offchip
hardware hosting a storage buffer.
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver manages CoreSight TMC (Trace Memory Controller) which
can act as a link or a sink depending upon its configuration. It
can present itself as an ETF (Embedded Trace FIFO) or ETR
(Embedded Trace Router).
ETF when configured in circular buffer mode acts as a trace
collection sink. When configured in HW fifo mode it acts as link.
ETR always acts as a sink and can be used to route data to memory
allocated in RAM.
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CoreSight components are compliant with the ARM CoreSight
architecture specification and can be connected in various
topologies to suit a particular SoC tracing needs. These trace
components can generally be classified as sources, links and
sinks. Trace data produced by one or more sources flows through
the intermediate links connecting the source to the currently
selected sink.
The CoreSight framework provides an interface for the CoreSight trace
drivers to register themselves with. It's intended to build up a
topological view of the CoreSight components and configure the
correct serie of components on user input via sysfs.
For eg., when enabling a source, the framework builds up a path
consisting of all the components connecting the source to the
currently selected sink(s) and enables all of them.
The framework also supports switching between available sinks
and provides status information to user space applications
through the debugfs interface.
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ARM fixes from Russell King:
- add the new bpf syscall to ARM.
- drop a redundant return statement in __iommu_alloc_remap()
- fix a performance issue noticed by Thomas Petazzoni with
kmap_atomic().
- fix an issue with the L2 cache OF parsing code which caused it to
incorrectly print warnings on each boot, and make the warning text
more consistent with the rest of the code
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8180/1: mm: implement no-highmem fast path in kmap_atomic_pfn()
ARM: 8183/1: l2c: Improve l2c310_of_parse() error message
ARM: 8181/1: Drop extra return statement
ARM: 8182/1: l2c: Make l2x0_cache_size_of_parse() return 'int'
ARM: enable bpf syscall
Pull networking fixes from David Miller:
"A bit has accumulated, but it's been a week or so since my last batch
of post-merge-window fixes, so...
1) Missing module license in netfilter reject module, from Pablo.
Lots of people ran into this.
2) Off by one in mac80211 baserate calculation, from Karl Beldan.
3) Fix incorrect return value from ax88179_178a driver's set_mac_addr
op, which broke use of it with bonding. From Ian Morgan.
4) Checking of skb_gso_segment()'s return value was not all
encompassing, it can return an SKB pointer, a pointer error, or
NULL. Fix from Florian Westphal.
This is crummy, and longer term will be fixed to just return error
pointers or a real SKB.
6) Encapsulation offloads not being handled by
skb_gso_transport_seglen(). From Florian Westphal.
7) Fix deadlock in TIPC stack, from Ying Xue.
8) Fix performance regression from using rhashtable for netlink
sockets. The problem was the synchronize_net() invoked for every
socket destroy. From Thomas Graf.
9) Fix bug in eBPF verifier, and remove the strong dependency of BPF
on NET. From Alexei Starovoitov.
10) In qdisc_create(), use the correct interface to allocate
->cpu_bstats, otherwise the u64_stats_sync member isn't
initialized properly. From Sabrina Dubroca.
11) Off by one in ip_set_nfnl_get_byindex(), from Dan Carpenter.
12) nf_tables_newchain() was erroneously expecting error pointers from
netdev_alloc_pcpu_stats(). It only returna a valid pointer or
NULL. From Sabrina Dubroca.
13) Fix use-after-free in _decode_session6(), from Li RongQing.
14) When we set the TX flow hash on a socket, we mistakenly do so
before we've nailed down the final source port. Move the setting
deeper to fix this. From Sathya Perla.
15) NAPI budget accounting in amd-xgbe driver was counting descriptors
instead of full packets, fix from Thomas Lendacky.
16) Fix total_data_buflen calculation in hyperv driver, from Haiyang
Zhang.
17) Fix bcma driver build with OF_ADDRESS disabled, from Hauke
Mehrtens.
18) Fix mis-use of per-cpu memory in TCP md5 code. The problem is
that something that ends up being vmalloc memory can't be passed
to the crypto hash routines via scatter-gather lists. From Eric
Dumazet.
19) Fix regression in promiscuous mode enabling in cdc-ether, from
Olivier Blin.
20) Bucket eviction and frag entry killing can race with eachother,
causing an unlink of the object from the wrong list. Fix from
Nikolay Aleksandrov.
21) Missing initialization of spinlock in cxgb4 driver, from Anish
Bhatt.
22) Do not cache ipv4 routing failures, otherwise if the sysctl for
forwarding is subsequently enabled this won't be seen. From
Nicolas Cavallari"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (131 commits)
drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode
drivers: net: cpsw: Fix broken loop condition in switch mode
net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0
stmmac: pci: set default of the filter bins
net: smc91x: Fix gpios for device tree based booting
mpls: Allow mpls_gso to be built as module
mpls: Fix mpls_gso handler.
r8152: stop submitting intr for -EPROTO
netfilter: nft_reject_bridge: restrict reject to prerouting and input
netfilter: nft_reject_bridge: don't use IP stack to reject traffic
netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions
netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions
netfilter: nf_tables_bridge: update hook_mask to allow {pre,post}routing
drivers/net: macvtap and tun depend on INET
drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets
drivers/net: Disable UFO through virtio
net: skb_fclone_busy() needs to detect orphaned skb
gre: Use inner mac length when computing tunnel length
mlx4: Avoid leaking steering rules on flow creation error flow
net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
...
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since CONFIG_HIGHMEM got enabled on ARMv5 Kirkwood, we have noticed a
very significant drop in networking performance. The test were
conducted on an OpenBlocks A7 board. Without this patch, the outgoing
performance measured with iperf are:
- highmem OFF, TSO OFF 544 Mbit/s
- highmem OFF, TSO ON 942 Mbit/s
- highmem ON, TSO OFF 306 Mbit/s
- highmem ON, TSO ON 246 Mbit/s
On this Kirkwood platform, the L2 cache is a Feroceon cache, and with
this cache, all the range operations have to be done on virtual
addresses and not physical addresses. Therefore, whenever
CONFIG_HIGHMEM is enabled, the cache maintenance operations call
kmap_atomic_pfn() and kunmap_atomic().
However, kmap_atomic_pfn() does not implement the same fast path for
non-highmem pages as the one implemented in kmap_atomic(), and this is
one of the reason for the performance drop. While this patch does not
fully restore the performances, it clearly improves them a lot:
without patch with patch
- highmem ON, TSO OFF 306 Mbit/s 387 Mbit/s
- highmem ON, TSO ON 246 Mbit/s 434 Mbit/s
We're still far from the !CONFIG_HIGHMEM performances, but it does
improve a bit the situation.
Thanks a lot to Ezequiel Garcia and Gregory Clement for all the
testing work around this topic.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King suggested [1]:
"I'd ask for one change. Please make all these messages start with
"L2C-310 OF" not "PL310 OF:". The device is described in ARM
documentation as a L2C-310 not PL310. (Also note the : is dropped
too - most of the other messages don't have the : either.)
The:
"PL310 OF: cache setting yield illegal associativity
PL310 OF: -1073346556 calculated, only 8 and 16 legal"
message could also be changed to something like:
"L2C-310 OF cache associativity %d invalid, only 8 or 16 permittedn"
[1] http://www.spinics.net/lists/arm-kernel/msg372776.html
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 513510ddba
(common: dma-mapping: introduce common remapping functions)
managed to end up with an extra return statement from the
original patch. Drop it.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit f3354ab674 ("ARM: 8169/1: l2c: parse cache properties from
ePAPR definitions") the following error is seen on imx6q:
[ 0.000000] PL310 OF: cache setting yield illegal associativity
[ 0.000000] PL310 OF: -2147097556 calculated, only 8 and 16 legal
As imx6q does not pass the "cache-size" and "cache-sets" properties in DT, the function l2x0_cache_size_of_parse() returns early and keep the 'associativity' pointer uninitialized.
To fix this problem, return error codes inside l2x0_cache_size_of_parse() and only use the 'associativity' pointer result if l2x0_cache_size_of_parse() succeeds.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM fixes from Russell King:
"A couple of ARM fixes.
We fix some printk formats for ptrdiff_t quantities which cause GCC
4.9 to complain, and we also blacklist known buggy GCC 4.8.x compilers
as their miscompilation is serious enough to cause filesystem
corruption, even through many distros have fixed their versions"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: fix some printk formats
ARM: Blacklist GCC 4.8.0 to GCC 4.8.2 - PR58854
Another week, another small batch of fixes.
Most of these make zynq, socfpga and sunxi platforms work a bit
better:
* Due to new requirements for regulators, DWMMC on socfpga broke past 3.17.
* SMP spinup fix for socfpga
* A few DT fixes for zynq
* Another option (FIXED_REGULATOR) for sunxi is needed that used to be selected
by other options but no longer is.
* A couple of small DT fixes for at91
* ...and a couple for i.MX.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MTvh
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another small batch of fixes.
Most of these make zynq, socfpga and sunxi platforms work a bit
better:
- due to new requirements for regulators, DWMMC on socfpga broke past
v3.17
- SMP spinup fix for socfpga
- a few DT fixes for zynq
- another option (FIXED_REGULATOR) for sunxi is needed that used to
be selected by other options but no longer is.
- a couple of small DT fixes for at91
- ...and a couple for i.MX"
* tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
ARM: multi_v7_defconfig: enable CONFIG_MMC_DW_ROCKCHIP
ARM: sunxi_defconfig: enable CONFIG_REGULATOR_FIXED_VOLTAGE
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
arm: socfpga: fix fetching cpu1start_addr for SMP
ARM: zynq: DT: trivial: Fix mc node
ARM: zynq: DT: Add cadence watchdog node
ARM: zynq: DT: Add missing reference for memory-controller
ARM: zynq: DT: Add missing reference for ADC
ARM: zynq: DT: Add missing address for L2 pl310
ARM: zynq: DT: Remove 222 MHz OPP
ARM: zynq: DT: Fix GEM register area size
- Revert one patch which increases I2C bus frequency on imx28-evk
- Fix a typo on imx6q EIM clock name
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUTE8JAAoJEFBXWFqHsHzOGawH/0KGNaHbI3rj+Hx1HHtN056y
3rgHSsLZSLQB89+bMd8aEVPJ2z0RKYXfyI1IvkcgEZxsqmHwRY8Fwlof4D38/bfP
tRHnyzT2E+znnyhvUZlH9yd9foTd3VkXbxFxbEssRHl2W2OxA0+3MbskknERPZqs
qr22DcMLKyrTbUH39iiEjS43qcJhuf/6vZmoVGCGdZonZwkH8WccIQ+kKneOn8/Z
11U4ioB4pirqvhM1niYQ95RLG0TveBN6op3c1HWkhqY4EKOlraZHQb4EOoslSO/X
vWoJqgB9DLH3eV+WTFI0FjGDK/6CFhgAth8q0FKVlHA3FFHr+fXdxv/+NLtagzQ=
=elO/
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.18" from Shawn Guo:
The i.MX fixes for 3.18:
- Revert one patch which increases I2C bus frequency on imx28-evk
- Fix a typo on imx6q EIM clock name
* tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 78b81f4666 ("ARM: dts: imx28-evk: Run I2C0 at 400kHz") caused issues
when doing the following sequence in loop:
- Boot the kernel
- Perform audio playback
- Reboot the system via 'reboot' command
In many times the audio card cannot be probed, which causes playback to fail.
After restoring to the original i2c0 frequency of 100kHz there is no such
problem anymore.
This reverts commit 78b81f4666.
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fix a typo error, the "emi" names refer to the eim clocks.
The change fixes typo in EIM and EIM_SLOW pre-output dividers and
selectors clock names. Notably EIM_SLOW clock itself is named correctly.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
[vladimir_zapolskiy@mentor.com: ported to v3.17]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
These patches fixes an SMP and SDMMC driver hang during boot up on the
SOCFPGA platform.
Patch "arm: socfpga: fix fetching cpu1start_addr for SMP" fixes the SMP
trampoline code in order for CPU1 to correctly fetch it's cpu1start_addr.
Patch "ARM: dts: socfpga: rename gpio nodes" renames that GPIO node in order
to allow a standard way of specifying status="okay" in the board DTS file.
Patch "ARM: dts: socfpga: Fix SD card detect" fixes a SDMMC driver hang
during boot. The reason for the hang was the deferred probe of the SDMMC
driver was waiting for the GPIO resource that would never come.
Patch "ARM: dts: socfpga: Add a 3.3V fixed regulator node" adds a fixed
regulator node for the SDMMC driver to use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=y6Ws
-----END PGP SIGNATURE-----
Merge tag 'socfpga_fixes_for_3.18' of git://git.rocketboards.org/linux-socfpga-next into fixes
Merge "SOCFPGA fixes for 3.18" from Dinh Nguyen:
These patches fixes an SMP and SDMMC driver hang during boot up on the
SOCFPGA platform.
Patch "arm: socfpga: fix fetching cpu1start_addr for SMP" fixes the SMP
trampoline code in order for CPU1 to correctly fetch it's cpu1start_addr.
Patch "ARM: dts: socfpga: rename gpio nodes" renames that GPIO node in order
to allow a standard way of specifying status="okay" in the board DTS file.
Patch "ARM: dts: socfpga: Fix SD card detect" fixes a SDMMC driver hang
during boot. The reason for the hang was the deferred probe of the SDMMC
driver was waiting for the GPIO resource that would never come.
Patch "ARM: dts: socfpga: Add a 3.3V fixed regulator node" adds a fixed
regulator node for the SDMMC driver to use.
* tag 'socfpga_fixes_for_3.18' of git://git.rocketboards.org/linux-socfpga-next:
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
arm: socfpga: fix fetching cpu1start_addr for SMP
Signed-off-by: Olof Johansson <olof@lixom.net>
- one more MAINTAINERS entry for the SSC driver
- a fix for the newly introduced power/reset driver
- a fix on at91sam9263 USB due to PLLB misconfiguration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUR2b6AAoJEAf03oE53VmQ5cIIAIsML44VaaFCy3fuE4+uXR9p
g5s80QMmV5dK0y/Yqwu/xIgvIEsyY4B9zWCy08w0EgzSHNbAC7iW7U4n2ia+7C9N
QxlOar+vI4A3gBS+9d0N7nEOf7VfnWQ2qmJmd2W5hOdQ0hjEhJIfMZtQYHBd8fN5
4fn/12HoC2iVYgGL9By/UmYVMCI1H1yeaQiYVw3KZkKPxlo6ERVrTVHL5rRjF65s
m7l0Sf2zlmIN3rp24D7TBdr4b8OwUdfakrEqli7t+5kZh6yvFtZhuZE84Aunvy7m
Orw7aT6ZhLDUc2omvCwz0ZNKvDtyt5I8MwWQ7ETeMGFWaeS6bPPALbwyf6Nnffw=
=gRsw
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "at91: fixes for v3.18 #1" from Nicholas Ferre:
First AT91 fixes for 3.18:
- one more MAINTAINERS entry for the SSC driver
- a fix for the newly introduced power/reset driver
- a fix on at91sam9263 USB due to PLLB misconfiguration
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
Signed-off-by: Olof Johansson <olof@lixom.net>
Allows booting from SD/MMC on RK3288 and other platforms. Added here so I
can enable the board in the boot farm.
Signed-off-by: Olof Johansson <olof@lixom.net>
I missed in 9a2ad529ed that REGULATOR_FIXED_VOLTAGE had also gotten
deselected, so it needs to be added back as an explicit option.
Signed-off-by: Olof Johansson <olof@lixom.net>
Without the 3.3V regulator node, the SDMMC driver will give these warnings:
dw_mmc ff704000.dwmmc0: No vmmc regulator found
dw_mmc ff704000.dwmmc0: No vqmmc regulator found
This patch adds the regulator node, and points the SD/MMC to the regulator.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
---
v3: Rename nodes to have schematic-name_regulator and remove "boot-on" and
"always-on"
v2: Move the regulator nodes to their respective board dts file and
correctly rename them to match the schematic
Without this patch, the booting the SOCFPGA platform would hang at the
SDMMC driver loading. The issue, debugged by Doug Anderson, turned out
to be that the GPIO bank used by the SD card-detect was not set to
status="okay".
Also update the cd-gpios to point to portb of the &gpio1 GPIO IP.
Suggested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Use &gpio1 to set status="okay" and update cd-gpio=&portb
v3: Correctly degugged the issue to be a gpio node not having status="okay"
Since the Synopsys GPIO IP can support multiple ports of varying widths, it
would make more sense to have the GPIO node DTS entry as this:
gpio0: gpio@ff708000{
porta{
};
};
Also, this is documented in the snps-dwapb-gpio.txt.
Suggested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
PLLB input and output ranges were wrongly copied from at91sam9261 as the
datasheet didn't mention explicitly PLLB. Correct their values.
This fixes USB.
Reported-by: Andreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Andreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
When CPU1 is brought out of reset, it's MMU is not turned on yet, so it will
only be able to use physical addresses. For systems with that have the
MMU page configured for 0xC0000000, 0x80000000, or 0x40000000
"BIC 0x40000000" will work just fine, as it was just converting the
virtual address of &cpu1start_addr into a physical address, ie. 0xC0000000
became 0x80000000. So for systems where the SDRAM controller was able to do a
wrap-around access, this was working fine, as it was just dropping the MSB,
but for systems where out of bounds memory access is not allowed, this would
not allow CPU1 to correctly fetch &cpu1start_addr.
This patch fixes the secondary_trampoline code to correctly fetch the
physical address of cpu1start_addr directly. The patch will subtract the
correct PAGE_OFFSET from &cpu1start_addr. And since on this platform, the
physical memory will always start at 0x0, subtracting PAGE_OFFSET from
&cpu1start_addr will allow CPU1 to correctly fetch the value of cpu1start_addr.
While at it, change the name of cpu1start_addr to socfpga_cpu1start_addr
to avoid any future naming collisions for multiplatform image.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Updated commit log to correctly lay out the usage of PAGE_OFFSET and
add comments to the same effect.
v3: Used PAGE_OFFSET to get the physical address
v2: Correctly get the physical address instead of just a BIC hack.
Pull mailbox framework from Jassi Brar:
"A framework for Mailbox controllers and clients have been cooking for
more than a year now.
Everybody in the CC list had been copied on patchset revisions and
most of them have made sounds of approval, though just one concrete
Reviewed-by. The patchset has also been in linux-next for a couple of
weeks now and no conflict has been reported. The framework has the
backing of at least 5 platforms, though I can't say if/when they
upstream their drivers (some businesses have 'changed')"
(Further acked-by by Arnd Bergmann and Suman Anna in the pull request
thread)
* 'mailbox-for-linus' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt: mailbox: add generic bindings
doc: add documentation for mailbox framework
mailbox: Introduce framework for mailbox
mailbox: rename pl320-ipc specific mailbox.h
GCC 4.9 complains if we take the difference of two pointers, and it's
printed with "%d". Fix this by using the proper flag - "t" for
ptrdiff_t.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the multi_v7_defconfig enabling the watchdog driver for Meson
SoCs.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Due to dependencies between timer and CPU frequency, only changes by
powers of two are allowed. The clocksource driver prevents other
changes, but with cpufreq and its governors it can result in being
spammed with error messages constantly. Hence, remove the 222 MHz OPP.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The size of the GEM's register area is only 0x1000 bytes.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148,
and basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=V3Rv
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148, and
basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late"
* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: corrected bcm2835 search
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
MAINTAINERS: Update Santosh Shilimkar's email id
ARM: sunxi_defconfig: enable CONFIG_REGULATOR
ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
ARM: exynos_defconfig: enable USB gadget support
ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
ARM: SAMSUNG: Restore Samsung PM Debug functionality
ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
ARM: exynos_defconfig: Enable SBS battery support
ARM: exynos_defconfig: Enable Control Groups support
ARM: exynos_defconfig: Enable Atmel maXTouch support
ARM: exynos_defconfig: Enable MAX77802
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
Merge "qcom DT changes for v3.18-3" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.18-3
* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148
* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJUQFJ6AAoJEA0Cl+kVi2xqW/wP/2sWvJRYaPgDvFk2NsTn12Tl
zdhbVRhnq/nskQ0Hg/YZ5QZMWbYo+gHUXuRrvGS6qRHLiQKdpLS1HvVZny+tG+j/
iJZiPNrjFPAjHe0os2agiiD+Y6HWcEwWC/VZIWXreHSlY8+4em6xmcyMpu9Mpzhp
GswN5eAU2suLZiliwBlCrcwuDsaYMmlM7fSdtVE7L9KWB27IGCwILHcPQR5wVfsO
0n3osqsZZvYv3b/VYkBeiOcAaGjAF1H0y12/hZ/kVHV35vAiNzUjxvWLHNZSuSXb
EMYnDuJfa2PnaEd8m9KfgDifvcaovhZeHreqtkGrumJAVJMVxa8R4/xWaKUnLOaB
Cn7HlZP/MFhLPoFREVV/70jbjikdhEueD5J7W3C1c8wUpnwmOORCt/raXnK+ABuq
h52wkl32Hc1QqO+RprHHCJNYHpGlysjMyiXRvy8qGQHhdWtk/1ttbhLPZMBoEN5h
auCi55EN/W5gGnfD+mWmN6aAjreyesWflhShrcqFWn748MSDa/w4Qh17/w3HtLbd
ED0GHJHf/hA6c0ixnLsMrgBj1rXpOdweZEN0HLWdAGDVC3RBdH74kDtyy3yJiAfI
QdMw14dZc9Adk4gxs34xSvmFxJHlHjXTmhzO/2inhNMwENbkD+UOzQ36x4Skpc37
hE9imV/9FjCr8UA0aBi6
=Arc+
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull more fixes from Kukjin Kim:
2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>
These stock GCC versions miscompile the kernel by incorrectly optimising
the function epilogue code - by first increasing the stack pointer, and
then loading entries from below the stack. This means that an opportune
interrupt or exception will corrupt the current function's saved state,
which may result in the parent function seeing different register
values.
As this bug has been known to result in corrupted filesystems, and these
buggy compiler versions seem to be frequently used, we have little
option but to blacklist these compiler versions.
Distributions may have fixed PR58854, but as their compilers are totally
indistinguishable from the buggy versions, it is unfortunate that this
also results in those also being blacklisted. Given the filesystem
corruption potential of the original, this is the lesser evil. People
who want to build with their fixed compiler versions will need to adjust
the kernel source. (Distros need to think about the implications of
fixing such a compiler bug, and consider how to ensure that their fixed
compiler versions can be detected if they wish to avoid this.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Support for 48bit IPA and VA (EL2)
- A number of fixes for devices mapped into guests
- Yet another VGIC fix for BE
- A fix for CPU hotplug
- A few compile fixes (disabled VGIC, strict mm checks)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3fl5
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-3.18-take-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
Pull second batch of changes for KVM/{arm,arm64} from Marc Zyngier:
"The most obvious thing is the sizeable MMU changes to support 48bit
VAs on arm64.
Summary:
- support for 48bit IPA and VA (EL2)
- a number of fixes for devices mapped into guests
- yet another VGIC fix for BE
- a fix for CPU hotplug
- a few compile fixes (disabled VGIC, strict mm checks)"
[ I'm pulling directly from Marc at the request of Paolo Bonzini, whose
backpack was stolen at Düsseldorf airport and will do new keys and
rebuild his web of trust. - Linus ]
* tag 'kvm-arm-for-3.18-take-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm:
arm/arm64: KVM: Fix BE accesses to GICv2 EISR and ELRSR regs
arm: kvm: STRICT_MM_TYPECHECKS fix for user_mem_abort
arm/arm64: KVM: Ensure memslots are within KVM_PHYS_SIZE
arm64: KVM: Implement 48 VA support for KVM EL2 and Stage-2
arm/arm64: KVM: map MMIO regions at creation time
arm64: kvm: define PAGE_S2_DEVICE as read-only by default
ARM: kvm: define PAGE_S2_DEVICE as read-only by default
arm/arm64: KVM: add 'writable' parameter to kvm_phys_addr_ioremap
arm/arm64: KVM: fix potential NULL dereference in user_mem_abort()
arm/arm64: KVM: use __GFP_ZERO not memset() to get zeroed pages
ARM: KVM: fix vgic-disabled build
arm: kvm: fix CPU hotplug
NAND
* Cleanup for Denali driver
* Atmel: add support for new page sizes
* Atmel: fix up 'raw' mode support
* Atmel: miscellaneous cleanups
* New timing mode helpers for non-ONFI NAND
* OMAP: allow driver to be (properly) built as a module
* bcm47xx: RESET support and other cleanups
SPI NOR
* Miscellaneous cleanups, to prepare framework for wider use (some further
work still pending)
* Compile-time configuration to select 4K vs. 64K support for flash that
support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/jCH
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd
Pull MTD update from Brian Norris:
"Sorry for delaying this a bit later than usual. There's one mild
regression from 3.16 that was noticed during the 3.17 cycle, and I
meant to send a fix for it along with this pull request. I'll
probably try to queue it up for a later pull request once I've had a
better look at it, hopefully by -rc2 at the latest.
Summary for this pull:
NAND
- Cleanup for Denali driver
- Atmel: add support for new page sizes
- Atmel: fix up 'raw' mode support
- Atmel: miscellaneous cleanups
- New timing mode helpers for non-ONFI NAND
- OMAP: allow driver to be (properly) built as a module
- bcm47xx: RESET support and other cleanups
SPI NOR
- Miscellaneous cleanups, to prepare framework for wider use (some
further work still pending)
- Compile-time configuration to select 4K vs. 64K support for flash
that support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more"
* tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd: (59 commits)
mtd: nand: omap: Correct CONFIG_MTD_NAND_OMAP_BCH help message
mtd: nand: Force omap_elm to be built as a module if omap2_nand is a module
mtd: move support for struct flash_platform_data into m25p80
mtd: spi-nor: add Kconfig option to disable 4K sectors
mtd: nand: Move ELM driver and rename as omap_elm
nand: omap2: Replace pr_err with dev_err
nand: omap2: Remove horrible ifdefs to fix module probe
mtd: nand: add Hynix's H27UCG8T2ATR-BC to nand_ids table
mtd: nand: support ONFI timing mode retrieval for non-ONFI NANDs
mtd: physmap_of: Add non-obsolete map_rom probe
mtd: physmap_of: Fix ROM support via OF
MAINTAINERS: add l2-mtd.git, 'next' tree for MTD
mtd: denali: fix indents and other trivial things
mtd: denali: remove unnecessary parentheses
mtd: denali: remove another set-but-unused variable
mtd: denali: fix include guard and license block of denali.h
mtd: nand: don't break long print messages
mtd: bcm47xxnflash: replace some magic numbers
mtd: bcm47xxnflash: NAND_CMD_RESET support
mtd: bcm47xxnflash: add cmd_ctrl handler
...
Explicitly set the dr_mode for the second dwc3 controller on the
Arndale Octa board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is build
with USB gadget support.
Reported-By: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In case the optional dr_mode property isn't set in the dwc3 nodes the
the controller will go into OTG mode if both USB host and USB gadget
functionality are enabled in the kernel configuration. Unfortunately
this results in USB not working on exynos5420-peach-pit and
exynos5800-peach-pi with such a kernel configuration unless manually
change the mode. To resolve that explicitly configure the dual role
mode as host.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The EIRSR and ELRSR registers are 32-bit registers on GICv2, and we
store these as an array of two such registers on the vgic vcpu struct.
However, we access them as a single 64-bit value or as a bitmap pointer
in the generic vgic code, which breaks BE support.
Instead, store them as u64 values on the vgic structure and do the
word-swapping in the assembly code, which already handles the byte order
for BE systems.
Tested-by: Victor Kamensky <victor.kamensky@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
CM-QS600 is a APQ8064 based computer on module.
The details are available at
http://compulab.co.il/products/computer-on-modules/cm-qs600/
Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This DTS has support for the Sony Xperia Z1 phone (codenamed Honami).
This first version of the DTS supports just a serial console.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add SATA PHY and SATA AHCI controller nodes to device tree to enable
generic ahci support on the IPQ8064/AP148 board.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Pratik Patel
Linus Torvalds
Tony Lindgren
Thomas Petazzoni
Fabio Estevam
Laura Abbott
Russell King
Olof Johansson
Fabio Estevam
Steve Longerbeam
Dinh Nguyen
Boris Brezillon
Carlo Caione
Michal Simek
Soren Brinkmann
Sjoerd Simons
Christoffer Dall
Mike Rapoport
Tim Bird
Kumar Gala