ivtv_probe() and ivtvfb_init_card() are never called in atomic context.
They call kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
dvb_register() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cx88_card_setup_pre_i2c() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cx25821_gpio_init(), cx25821_initialize() and cx25821_registers_init()
are never called in atomic context.
They call mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cx23885_reset() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cx23885_gpio_setup() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
altera_ci_slot_reset() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cobalt_probe() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
vs6624_probe() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
adv7842_ddr_ram_test() is never called in atomic context.
It only calls from:
adv7842_ddr_ram_test() <- adv7842_command_ram_test() <- adv7842_ioctl()
adv7842_ddr_ram_test() calls mdelay() to busily wait,
which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
PTR_ERR was making any pointer passed an error pointer, and should be
replaced with PTR_ERR_OR_ZERO which checks if is an actual error condition.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ADV7180 and ADV7182 transmit whole fields, bottom field followed
by top (or vice-versa, depending on detected video standard). So
for chips that do not have support for explicitly setting the field
mode via I2P, set the field mode to V4L2_FIELD_ALTERNATE.
I2P converts fields into frames using an edge adaptive algorithm. The
frame rate is the same as the 'field rate': e.g. X fields per second
are now X frames per second.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In rga_remove(), dma_free_attrs is being passed the wrong
cpu address, which triggers an exception if the driver is
removed. Fix it.
Tested on a RK3399 platform, with a bind/unbind cycle.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The media.h public header is one of only three public headers that include
linux/version.h. Drop it from media.h. It was only used for an obsolete
define.
It has to be added to media-device.c, since that source relied on media.h
to include it.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vivid driver will overlay stream time on generated frames. Though,
in interlacing mode V4L2_FIELD_ALTERNATE, each field is separate and
must have the same time to ensure proper render. Though, this time was
only updated every 2 frames as the code was checking against the wrong
counter (frame counter rather then field counter).
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CODA7541 firmware does not set the SPS frame cropping fields to
properly describe coded h.264 streams with frame sizes that are not a
multiple of the macroblock size.
This adds RBSP parsing code and a SPS fixup routine to manually replace
the cropping information in the headers produced by the firmware with
the correct values.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[hans.verkuil@cisco.com: added explanation of SPS RBSP to comment]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When encoding h.264, if visible resolution is not aligned to macroblock
size, frame cropping has to be set in the SPS header to produce correct
streams. The CODA960 firmware can do this on its own if asked to.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch fixes crystal frequency setting when power on this device.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In commit 2d9445db0e ("media: vsp1: Use reference counting for
bodies"), a new field was introduced to the vsp1_dl_body structure to
account for usage tracking of the body.
Document the newly added field in the kerneldoc.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
UVC defines a method of handling asynchronous controls, which sends a
USB packet over the interrupt pipe. This patch implements support for
such packets by sending a control event to the user. Since this can
involve USB traffic and, therefore, scheduling, this has to be done
in a work queue.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When a command ends up in a STALL on the control pipe, use the Request
Error Code control to provide a more precise error information to the
user. For example, if a camera is still busy processing a control,
when the same or an interrelated control set request arrives, the
camera can react with a STALL and then return the "Not ready" status
in response to a UVC_VC_REQUEST_ERROR_CODE_CONTROL command. With this
patch the user would then get an EBUSY error code instead of a
generic EPIPE.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Event subscribers cannot have a NULL file handle. They are only added
at a single location in the code, and the .fh pointer is used without
checking there.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Just like for ISOC, validate the decoded BULK buffer size when possible.
This avoids sending corrupted or partial buffers to userspace, which may
lead to application crash or run-time failure.
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
[laurent.pinchart@ideasonboard.com: Move uvc_video_validate_buffer() call to uvc_video_next_buffers()]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the 8-bit IR format GUID defined in the Microsoft Kernel
Streaming Media API.
Reported-by: Paul Menzel <pmenzel+linux-media@molgen.mpg.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Paul Menzel <pmenzel+linux-media@molgen.mpg.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Right now, the code that calculates alternate modes is not ready
for devices with dual tuners. That's ok, as we currently don't
have any such devices, but better to add a warning for such
case, as, if anyone adds such device, the logic will need to
be reviewed.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Half-revert: commit 5b1a270d22 ("media: dvb: add alternative USB PID for Hauppauge WinTV-soloHD")'
The PID already exists on the line above.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Michael Ira Krufky <mkrufky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Addresses the following, which introduced a regression itself:
Commit 509f89652f ("media: em28xx: fix a regression with HVR-950")
The regression fix breaks dual transport stream support. Currently,
when a tuner starts streaming it sets alt mode on the USB interface.
The problem is, in a dual tuner model, both tuners share the same
USB interface, so when the second tuner becomes active and sets alt
mode on the interface it kills streaming on the other port.
This patch addresses the regression by only setting alt mode
on the USB interface during em28xx_start_streaming, if the
device is not a dual tuner model. This allows all older and
single tuner devices to explicitly set alt mode during stream
startup. Testers report both isoc and bulk DualHD models work
correctly with the alt mode set only once, in em28xx_dvb_init.
Fixes: 509f89652f ("media: em28xx: fix a regression with HVR-950")
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Michael Ira Krufky <mkrufky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'current' is also defined in asm-generic/current.h.
When compiling this driver for older kernels with the media_build system,
this header is included via compat.h and it no longer compiles. Rename
current to cur.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add FIXME code comment:
/* FIXME: check if it is fe_adap[1] */
It is likely that it should be adap->fe_adap[1].fe in the second clause,
but this has never been verified.
Suggested-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The same code is executed regardless of whether c->frequency < 600000000
or c->frequency < 730000000 is true.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Probe of dvb_usb_gl861 was working at least with v4.4. Noticed the issue
with v4.13 but according to similar issues the problem started with v4.9.
[ 15.288065] transfer buffer not dma capable
[ 15.288090] WARNING: CPU: 2 PID: 493 at drivers/usb/core/hcd.c:1595 usb_hcd_map_urb_for_dma+0x4e2/0x640
...CUT...
[ 15.288791] dvb_usb_gl861: probe of 3-7:1.0 failed with error -5
Tested with MSI Mega Sky 580 DVB-T Tuner [GL861]
[mchehab+samsung@kernel.org: rebased on the top of upstream]
Cc: stable@vger.kernel.org
Signed-off-by: Mika Båtsman <mika.batsman@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently we are leaking bpf programs when they are detached from the
lirc device; the refcount never reaches zero.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is implementing multi-stream decoder support. The multi-stream
will be used to enable/disable the primary/secondary decoder
outputs. Depending on formats on both decoder outputs we could
implement downscale, dithering and supporting UBWC (universal
bandwidth compression) formats. The UBWC compressed raw format is
used to optimize interconnect bandwidth for bigger resolutions
like 4K and hence we will get some power-saving benefits as well.
Both decoder outputs are distinguished by buffer_type field in
the HFI packets. For example HFI_BUFFER_OUTPUT is the buffer type
for primary decoder output and HFI_BUFFER_OUTPUT2 is for secondary
decoder output.
Starting from Venus 4xx the DPB buffers format must be UBWC, so
the multi-stream becomes mandatory for this Venus version. That
means that we need to allocate internally in the driver a set of
DPB buffers (with UBWC NV12 format) and give them to the firmware.
The other decoder output (we called it OPB) format will be NV12
linear format and with the same resolution (or smaller in case
the user wants to downscale).
The DPB buffers are used for decoder reference frames and those
have to be in a specific format (UBWC). So one decoder output is
used to fill those reference buffers while the other output is
used to fill the userspace buffers with the user requested format.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This move the calculations of raw and compressed buffer sizes
on common helper and make it identical for encoder and decoder.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make a new function vdec_output_conf() for decoder output
configuration. vdec_output_conf() will set properties via
HFI interface related to the output configuration, and
keep vdec_set_properties() which will set properties
related to decoding parameters.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rework and rename vdec_cap_num_buffers() to get the number of
input buffers too.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Extend venus_helper_set_num_bufs() helper function with one more
argument to set number of output buffers for the secondary decoder
output.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These are new properties applicable to Venus version 4xx. Add the
helpers and call them from decoder and encoder drivers.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The new helper will has one more argument for buffer type, that
way the decoder can configure the format on it's secondary
output.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds one more function argument to pass buffer type to
set_output_resolution() helper function. That is a preparation
to support secondary decoder output.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Delete not used flag for capture buffer allocation mode and
no longer used cap_bufs_mode_dynamic from instance structure.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add and use a helper function to set actual buffer size for
particular buffer type. This is also preparation to use
the second decoder output.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds a new helper function to set dynamic buffer mode if it is
supported by current HFI version. The dynamic buffer mode is
set unconditionally for both decoder outputs.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rename is_reg_unreg_needed() to better name is_dynamic_bufmode() and
use buffer mode from enumerated per codec capabilities.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds common capability parser for all supported Venus
versions. Having it will help to enumerate better the supported
raw formats and codecs and also the capabilities for every
codec like max/min width/height, framerate, bitrate and so on.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add two more clocks for Venus 4xx in core structure and create
a new power enable function to handle it for 3xx/4xx versions.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds suspend (power collapse) functionality by reusing
the suspend function for Venus 3xx and also enables idle indicator
property for Venus 4xx (where it is disabled by default).
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This moves setting of default properties (firmware debug, idle
indicator and low power mode) from session init to core init.
All of those properties are need to be enabled/disabled early
so that they could be used before the clients are even initialized.
The other reason is to set idle indicator property early before
we enter into venus_suspend function where we need to check for
ARM9 WFI.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This fixes the suspend function for Venus 3xx versions by
add a check for WFI (wait for interrupt) bit. This bit
is on when the ARM9 is idle and entered in low power mode.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add AXI halt support for version 4xx by using venus wrapper
registers.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds handling of buffers of type OUTPUT2 which is needed to
support Venus 4xx version.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This makes possible to handle session_continue for 4xx as well.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
HFI version 4xx can pass more properties in the sequence change
event, extend the event structure with them.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Data pointer should be incremented by size of the structure not
the size of a pointer, correct the mistake.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Tested-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. kinect_read returns the result of
usb_control_msg, which can return a negtive error code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@
*x = f(...);
... when != x = e1
when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The error path currently calls tw686x_video_free() which requires
vc->dev to be initialized, causing a NULL dereference on uninitizalized
channels.
Fix this by setting the vc->dev fields for all the channels first.
Fixes: f8afaa8dbc ("[media] tw686x: Introduce an interface to support multiple DMA modes")
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
AMG88xx has an on-board thermistor which is used for more accurate
processing of its temperature readings from the 8x8 thermopile array
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This enables reordering support for h.264 main profile level 4.2,
5.0, and 5.1 streams. Even though we likely can't play back such
streams at full speed, we should still recognize them correctly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Allow to set a crop rectangle on the encoder output queue to set the
visible resolution as required by the V4L2 codec API.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove the intermediate width and height variables, the calculation is
simple enough.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All internal YCbCr frame buffers are the same size, calculate ycbcr_size
once before the allocation loop.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a software codec based on the Fast Walsh Hadamard Transform.
The original FWHT codec was developed by Tom aan de Wiel, and it was
turned into 'proper' kernel code by Hans Verkuil, with a lot of
performance and memory improvements.
Signed-off-by: Tom aan de Wiel <tom.aandewiel@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This can be used to mark the last queued source buffer as the last
buffer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a new pixelformat for the vicodec software codec using the
Fast Walsh Hadamard Transform.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Several drivers in media/i2c do not set the entity function.
Correct this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The entity function was ORed with the flags field instead of
assigned to the function field. Correct this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These two drivers both have function MEDIA_ENT_F_DV_ENCODER.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The use of 'DTV' is very confusing since it normally refers to Digital
TV e.g. DVB etc.
Instead use 'DV' (Digital Video), which nicely corresponds to the
DV Timings API used to configure such receivers and transmitters.
We keep an alias to avoid breaking userspace applications.
Since this alias is only available if __KERNEL__ is *not* defined
(i.e. it is only available for userspace, not kernelspace), any
drivers that use it also have to be converted to the new define.
These drivers are adv7604, adv7842 and tda1997x.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v2 entity structure never exposed the entity flags, which made it
impossible to detect connector or default entities.
It is really trivial to just expose this information, so implement this.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v2 pad structure never exposed the pad index, which made it impossible
to call the MEDIA_IOC_SETUP_LINK ioctl, which needs that information.
It is really trivial to just expose this information, so implement this.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the new (optional) 5V gpio in order to debug 5V
changes. Some displays turn off CEC if the 5V is not detected,
so it is useful to be able to monitor this line.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the new 5V CEC events
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 1d38971438 ("[media] v4l: rcar_fdp1: add FCP dependency") fixed
a compilation breakage when the optional VIDEO_RENESAS_FCP dependency is
compiled as a module while the rcar_fdp1 driver is built in. As a side
effect it disabled compilation on Gen2 by disallowing the valid
combination ARCH_RENESAS && !VIDEO_RENESAS_FCP. Fix it by handling the
dependency the same way the vsp1 driver did in commit 199946731f
("[media] vsp1: clarify FCP dependency").
Fixes: 1d38971438 ("[media] v4l: rcar_fdp1: add FCP dependency")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Switch to dev_dbg for the busy TX message to avoid having a flood of:
[ 228.064570] meson-ao-cec c8100100.cec: meson_ao_cec_transmit: busy TX: aborting
[ 230.368489] meson-ao-cec c8100100.cec: meson_ao_cec_transmit: busy TX: aborting
[ 234.208655] meson-ao-cec c8100100.cec: meson_ao_cec_transmit: busy TX: aborting
[ 236.512558] meson-ao-cec c8100100.cec: meson_ao_cec_transmit: busy TX: aborting
This message is only a debug hint and not an error.
Fixes: 7ec2c0f72c ("media: platform: Add Amlogic Meson AO CEC Controller driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vb2_core_qbuf() function didn't check if q->error was set. It is
checked in __buf_prepare(), but that function isn't called if the buffer
was already prepared before with VIDIOC_PREPARE_BUF.
So check it at the start of vb2_core_qbuf() as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implementing job_abort() does not make sense on some drivers.
This is not a problem, as the abort is not required to
wait for the job to finish. Quite the opposite, drivers
are encouraged not to wait.
Demote v4l2_m2m_ops.job_abort from required to optional, and
clean all drivers with dummy implementations.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As per the documentation, job_abort is not required
to wait until the current job finishes. It is redundant
to do so, as the core will perform the wait operation.
Remove the wait infrastructure completely.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As per the documentation, job_abort is not required
to wait until the current job finishes. It is redundant
to do so, as the core will perform the wait operation.
Remove the wait infrastructure completely.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Limit frame sizes to the [1, 65536] interval, media bus formats to
the available list of formats, and initialize pad and try formats.
Reported-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Rui Miguel Silva <rui.silva@linaro.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is no way to control the standard of subdevices which are part of
a media device. The ioctls which exists all target video devices
explicitly and the idea is that the video device should talk to the
subdevice. For subdevices part of a media graph this is not possible and
the standard must be controlled on the subdev device directly.
Add four new ioctls to be able to directly interact with subdevices and
control the video standard; VIDIOC_SUBDEV_ENUMSTD, VIDIOC_SUBDEV_G_STD,
VIDIOC_SUBDEV_S_STD and VIDIOC_SUBDEV_QUERYSTD.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A lot of sensor drivers are labelled as "sensor-level" drivers. That's
odd and somewhat confusing as the term isn't used elsewhere: these are
just sensor drivers. Call them such.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The just parsed endpoint fwnode has to be put after use.
Currently this is done only in error handling path. Fix that by
putting node unconditionally after use.
Fixes: 01b8444828 ("media: v4l2: i2c: ov7670: Implement OF mbus configuration")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The external clock frequency was set to 23.88MHz by mistake
because of a platform which cannot get closer to 24MHz.
The supported by the driver external clock is 24MHz so
set it correctly and also fix the values of the pixel
clock and link clock.
However allow 1% tolerance to the external clock as this
difference is small enough to be insignificant.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Handle data-enable signal polarity. If the polarity is not specifically
requested to be active low, use the active high default.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Save load of mode registers array when V4L2 client sets a format or a
frame interval which selects the same mode than the current one.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The smiapp driver is licensed under GNU GPL v2 only, as stated by the
header. Reflect this in the MODULE_LICENSE macro.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert all users of struct acpi_reference_args to more generic
fwnode_reference_args. This will
1) avoid an ACPI specific references to device nodes with integer
arguments as well as
2) allow making references to nodes other than device nodes in ACPI.
As a by-product, convert the fwnode interger arguments to u64. The
arguments were 64-bit integers on ACPI but the fwnode arguments were
just 32-bit.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we are leaking bpf programs when they are detached from the
lirc device; the refcount never reaches zero.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ChromeOS Embedded Controller can expose a CEC bus, this patch add the
driver for such feature of the Embedded Controller.
This driver is part of the cros-ec MFD and will be add as a sub-device when
the feature bit is exposed by the EC.
The controller will only handle a single logical address and handles
all the messages retries and will only expose Success or Error.
The controller will be tied to the HDMI CEC notifier by using the platform
DMI Data and the i915 device name and connector name.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In non device-tree world, we can need to get the notifier by the driver
name directly and eventually defer probe if not yet created.
This patch adds a variant of the get function by using the device name
instead and will not create a notifier if not yet created.
But the i915 driver exposes at least 2 HDMI connectors, this patch also
adds the possibility to add a connector name tied to the notifier device
to form a tuple and associate different CEC controllers for each HDMI
connectors.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Locking the root adapter for __i2c_transfer will deadlock if the
device sits behind a mux-locked I2C mux. Switch to the finer-grained
i2c_lock_bus with the I2C_LOCK_SEGMENT flag. If the device does not
sit behind a mux-locked mux, the two locking variants are equivalent.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A couple of drivers produced build errors after the mod_devicetable.h
header was split out from the platform_device one, e.g.
drivers/media/platform/davinci/vpbe_osd.c:42:40: error: array type has incomplete element type 'struct platform_device_id'
drivers/media/platform/davinci/vpbe_venc.c:42:40: error: array type has incomplete element type 'struct platform_device_id'
This adds the inclusion where needed.
Fixes: ac3167257b ("headers: separate linux/mod_devicetable.h from linux/platform_device.h")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For some types of tuners (Philips FMD1216ME(X) MK3 currently) we know that
letting TDA9887 output port 1 remain high (inactive) will switch FM radio
to mono mode.
Let's make use of this functionality - nothing changes for the default
stereo radio mode.
Tested on a Medion 95700 board which has a FMD1216ME tuner.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This commit describes a device instance private data of the driver
(struct cx25840_state) in a kernel-doc style comment.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We need to zero-initialize cx25840 platform data structure to make sure
that its future members do not contain random stack garbage.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a new control V4L2_CID_MPEG_VIDEO_VP9_PROFILE for VP9 profiles. This control
allows selecting the desired profile for VP9 encoder and querying for supported
profiles by VP9 encoder/decoder.
Though this control is similar to V4L2_CID_MPEG_VIDEO_VP8_PROFILE, we need to
separate this control from it because supported profiles usually differ between
VP8 and VP9.
Signed-off-by: Keiichi Watanabe <keiichiw@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a menu control V4L2_CID_MPEG_VIDEO_VP8_PROFILE for VP8 profile and make
V4L2_CID_MPEG_VIDEO_VPX_PROFILE an alias of it. This new control is used to
select the desired profile for VP8 encoder and query for supported profiles by
VP8 encoder/decoder.
Though we have originally a control V4L2_CID_MPEG_VIDEO_VPX_PROFILE and its name
contains 'VPX', it works only for VP8 because supported profiles usually differ
between VP8 and VP9. In addition, this control cannot be used for querying since
it is not a menu control but an integer control, which cannot return an
arbitrary set of supported profiles.
The new control V4L2_CID_MPEG_VIDEO_VP8_PROFILE is a menu control as with
controls for other codec profiles. (e.g. H264)
In addition, this patch also fixes the use of V4L2_CID_MPEG_VIDEO_VPX_PROFILE in
drivers of Qualcomm's venus and Samsung's s5p-mfc.
Signed-off-by: Keiichi Watanabe <keiichiw@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Handle parallel subdevices in link_notify callback. If the notified link
involves a parallel subdevice, do not change routing of the VIN-CSI-2
devices and mark the VIN instance as using a parallel input. If the
CSI-2 link setup succeeds instead, mark the VIN instance as using CSI-2.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When running with media-controller link the parallel input
media entities with the VIN entities at 'complete' callback time.
To create media links the v4l2_device should be registered first.
Check if the device is already registered, to avoid double registrations.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The rcar-vin driver so far had a mutually exclusive code path for
handling parallel and CSI-2 video input subdevices, with only the CSI-2
use case supporting media-controller. As we add support for parallel
inputs to Gen3 media-controller compliant code path now parse both port@0
and port@1, handling the media-controller use case in the parallel
bound/unbind notifier operations.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Media bus configuration flags and media bus type were so far a property
of each VIN instance, as the subdevice they were connected to was
immutable during the whole system life time.
With the forth-coming introduction of parallel input devices support,
a VIN instance can have the subdevice it is connected to switched at
runtime, from a CSI-2 subdevice to a parallel one and viceversa, through
the modification of links between media entities in the media controller
graph. To avoid discarding the per-subdevice configuration flags retrieved by
v4l2_fwnode parsing facilities, cache them in the 'rvin_graph_entity'
member of each VIN instance, opportunely renamed to 'rvin_parallel_entity'.
Also modify the register configuration function to take mbus flags into
account when running on a bus type that supports them.
The media bus type currently in use will be updated in a follow-up patch
to the link state change notification function.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
During the notifier initialization, memory for the list of associated async
subdevices is reserved during the fwnode endpoint parsing from the v4l2-async
framework. If the notifier registration fails, that memory should be released
and the notifier 'cleaned up'.
Catch the notifier registration error and perform the cleanup both for the
group and the parallel notifiers.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As CSI-2 subdevices are shared between several VIN instances, a shared
notifier to collect the CSI-2 async subdevices is required. So far, the
rcar-vin driver used the notifier of the last VIN instance to probe but
with the forth-coming introduction of parallel input subdevices support
in mc-compliant code path, each VIN may register its own notifier if any
parallel subdevice is connected there.
To avoid registering a notifier twice (once for parallel subdev and one
for the CSI-2 subdevs) create a group notifier, shared by all the VIN
instances.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As the term 'digital' is used all over the rcar-vin code in place of
'parallel', rename all the occurrencies.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Request API requires a media node. Add one to the vim2m driver so we can
use requests with it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A memory-to-memory pipeline device consists in three
entities: two DMA engine and one video processing entities.
The DMA engine entities are linked to a V4L interface.
This commit add a new v4l2_m2m_{un}register_media_controller
API to register this topology.
For instance, a typical mem2mem device topology would
look like this:
Device topology
- entity 1: source (1 pad, 1 link)
type Node subtype V4L flags 0
pad0: Source
-> "proc":1 [ENABLED,IMMUTABLE]
- entity 3: proc (2 pads, 2 links)
type Node subtype Unknown flags 0
pad0: Source
-> "sink":0 [ENABLED,IMMUTABLE]
pad1: Sink
<- "source":0 [ENABLED,IMMUTABLE]
- entity 6: sink (1 pad, 1 link)
type Node subtype V4L flags 0
pad0: Sink
<- "proc":0 [ENABLED,IMMUTABLE]
[hans.verkuil@cisco.com: mark interface links as IMMUTABLE]
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently links between entities and an interface are just marked as
ENABLED. But (at least today) these links cannot be disabled by userspace
or the driver, so they should also be marked as IMMUTABLE.
It might become possible that drivers can disable such links (if for some
reason the device node cannot be used), so we might need to add a new link
flag at some point to mark interface links that can be changed by the driver
but not by userspace.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When you switch from auto to manual mode for an auto-cluster (e.g.
autogain+gain controls), then the current HW value has to be copied
to the current control value. However, has_changed was never set to
true, so new_to_cur didn't actually copy this value.
Reported-by: Hugues FRUCHET <hugues.fruchet@st.com>
Tested-by: Hugues FRUCHET <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
viu_of_probe() ignores fails in i2c_get_adapter(),
tries to unlock uninitialized mutex on error path.
The patch streamlining the error handling in viu_of_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds the i.MX6 CODA960 firmware versions 2.1.9
(revision 32515) to the list of supported firmware versions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Explicitly clear DEC_SEQ_JPG_THUMB_EN during sequence initialization.
Not clearing the register does not cause problems, since the only other
codec (MPEG-4 decode) that writes to this register happens to always
write 0 as well.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Padding the bitstream buffer is not enough to reliably avoid prefetch
failures. Picture runs with the next buffer's header already visible to
the CODA7541 succeed much more reliably, so always queue two JPEG frames
into the bitstream buffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The hardware codec is not colorspace aware. We should trust userspace to
set the correct colorimetry information on the OUTPUT queue and mirror
the exact same setting on the CAPTURE queue.
There is no reason to restrict colorspace to JPEG for JPEG images, if
userspace injects the correct colorspace information into the JPEG
headers after encoding.
Fixes: b14ac54568 ("[media] coda: improve colorimetry handling")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If new buffers are queued after streamoff, the flag will be cleared
anyway, so this is mostly for the purpose of correctness.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the vivid driver you want gain to continuous change while autogain
is on. However, dev->jiffies_vid_cap doesn't actually change. It probably
did in the past, but changes in the code caused this to be a fixed value
that is only set when you start streaming.
Replace it by jiffies, which is always changing.
[mchehab@kernel.org: use jiffies_to_msecs() instead of dividing by HZ]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Whether reordering should be enabled only depends on the h.264 profile.
Stop parsing the level and drop the debug message, profile and level
can now be determined via read-only decoder controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The decoder profile/level controls initially can be used to determine
supported profiles and levels. The values are set for a given stream
once the headers are parsed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The encoder picture run command takes a picture source stride parameter.
This must be set to the output queue's bytesperline, not width.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vb2_queue will soon be mandatory. The videobuf2 core
will throw a verbose warning if it's not set.
The stk1160 driver is setting the queue lock, but after
the vb2_queue_init call. Avoid the warning by setting
the lock before the queue initialization.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver is currently specifying a video_device lock,
which means it is protecting all the ioctls (including
queue ioctls) with a single mutex.
It's therefore straightforward to implement wait_prepare
and wait_finish, by explicitly setting the vb2_queue lock.
Having these callbacks releases the queue lock while blocking,
which improves latency by allowing for example streamoff
or qbuf operations while waiting in dqbuf.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver is currently specifying a video_device lock,
which means it is protecting all the ioctls (including
queue ioctls) with a single mutex.
It's therefore straightforward to implement wait_prepare
and wait_finish, by explicitly setting the vb2_queue lock.
Having these callbacks releases the queue lock while blocking,
which improves latency by allowing for example streamoff
or qbuf operations while waiting in dqbuf.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver is currently specifying a vb2_queue lock,
which means it straightforward to implement wait_prepare
and wait_finish.
Having these callbacks releases the queue lock while blocking,
which improves latency by allowing for example streamoff
or qbuf operations while waiting in dqbuf.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the mutex in struct mtk_mdp_ctx to protect the
capture and output vb2_queues. This allows to replace
the ad-hoc wait_{prepare, finish} with
vb2_ops_wait_{prepare, finish}.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver does not serialize its video4linux
ioctls, which is a bug, as race conditions might appear.
In addition, video_device and vb2_queue locks are now both
mandatory. Add them, and implement wait_prepare and
wait_finish.
To stay on the safe side, this commit uses a single mutex
for both locks. Better latency can be obtained by separating
these if needed.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For m2m devices the vdev->queue lock was always taken instead of the
lock for the specific capture or output queue. Now that we pushed
the locking down into __video_do_ioctl() we can pick the correct
lock and potentially improve the performance of m2m devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
imx274_write_table() is a mere wrapper (and the only user) to
imx274_regmap_util_write_table_8(). Remove this useless indirection by
merging the two functions into one.
Also get rid of the wait_ms_addr and end_addr parameters since it does
not make any sense to give them any values other than
IMX274_TABLE_WAIT_MS and IMX274_TABLE_END.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
IMX274_DEFAULT_MODE is defined but not used. Start using it, so the
default can be more easily changed without digging into the code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After restructuring struct imx274_frmfmt, the mode_index field is
still in use only for two dev_dbg() calls in imx274_s_stream(). Let's
remove it and avoid duplicated information.
Replacing the first usage requires some rather annoying but trivial
pointer math. The other one can be removed entirely since it would
print the same value anyway.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Data about the implemented readout modes is partially stored in
imx274_formats[], the rest is scattered in several arrays. The latter
are then accessed using the mode index, e.g.:
min_frame_len[priv->mode_index]
Consolidate all these data in imx274_formats[], and store a pointer to
the selected mode (i.e. imx274_formats[priv->mode_index]) in the main
device struct. This way code to use these data becomes more readable,
e.g.:
priv->mode->min_frame_len
This removes lots of scaffolding code and keeps data about each mode
in a unique place.
Also remove a parameter to imx274_mode_regs() that is now unused.
While this adds the mode pointer to the device struct, it does not
remove the mode_index from it because mode_index is still used in two
dev_dbg() calls. This will be handled in a follow-up commit.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current probe function calls v4l2_ctrl_handler_setup() before
initializing the format info. This triggers call paths such as:
imx274_probe -> v4l2_ctrl_handler_setup -> imx274_s_ctrl ->
imx274_set_exposure, where priv->mode_index is accessed before being
assigned.
This is wrong but does not trigger a visible bug because priv is
zero-initialized and 0 is the default value for priv->mode_index. But
this would become a crash in follow-up commits when mode_index is
replaced by a pointer that must always be valid.
Fix the bug before it shows up by initializing struct members early.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a v4l2 sub-device driver for the ak7375 lens voice coil.
This is a voice coil module using the i2c bus to control the
focus position.
ak7375 can write multiple bytes of data at a time. If more
data is received instead of the stop condition after receiving
one byte of data, the address inside the chip is automatically
incremented and the data is written into the next address.
The ak7375 can control the position with 12 bits value and
consists of two 8 bit registers show as below:
register 0x00(AK7375_REG_POSITION):
+---+---+---+---+---+---+---+---+
|D11|D10|D09|D08|D07|D06|D05|D04|
+---+---+---+---+---+---+---+---+
register 0x01:
+---+---+---+---+---+---+---+---+
|D03|D02|D01|D00|---|---|---|---|
+---+---+---+---+---+---+---+---+
This driver support :
- set ak7375 to standby mode once suspend and
turn it back to active if resume
- set the position via V4L2_CID_FOCUS_ABSOLUTE ctrl
[Sakari Ailus: Rename val as ret in probe, drop redundant error message]
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Driver must reject frame interval enumeration of unsupported resolution.
This was detected by v4l2-compliance format ioctl test:
v4l2-compliance Format ioctls:
info: found 2 frameintervals for pixel format 4745504a and size 176x144
fail: v4l2-test-formats.cpp(123):
found frame intervals for invalid size 177x144
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
According to ov5640 datasheet xvclk is allowed to be between 6 and 54 MHz.
I run a successful test with 27 MHz.
Signed-off-by: Philipp Puschmann <pp@emlix.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The banding filter ON/OFF is controlled via bit 5 of COM8 register. It
is attempted to be enabled in ov772x_set_params() by the following line.
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, 1);
But this unexpectedly results disabling the banding filter, because the
mask and set bits are exclusive.
On the other hand, ov772x_s_ctrl() correctly sets the bit by:
ret = ov772x_mask_set(client, COM8, BNDF_ON_OFF, BNDF_ON_OFF);
The same fix was already applied to non-soc_camera version of ov772x
driver in the commit commit a024ee14cd ("media: ov772x: correct setting
of banding filter")
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the subdevice doesn't provide s_power core ops callback, the
v4l2_subdev_call for s_power returns -ENOIOCTLCMD. If the subdevice
doesn't have the special handling for its power saving mode, the s_power
isn't required. So -ENOIOCTLCMD from the v4l2_subdev_call should be
ignored.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The struct clk_init_data init variable is declared in the isp_xclk_init()
function so is an automatic variable allocated in the stack. But it's not
explicitly zero-initialized, so some init fields are left uninitialized.
This causes the data structure to have undefined values that may confuse
the common clock framework when the clock is registered.
For example, the uninitialized .flags field could have the CLK_IS_CRITICAL
bit set, causing the framework to wrongly prepare the clk on registration.
This leads to the isp_xclk_prepare() callback being called, which in turn
calls to the omap3isp_get() function that increments the isp dev refcount.
Since this omap3isp_get() call is unexpected, this leads to an unbalanced
omap3isp_get() call that prevents the requested IRQ to be later enabled,
due the refcount not being 0 when the correct omap3isp_get() call happens.
Fixes: 9b28ee3c91 ("[media] omap3isp: Use the common clock framework")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
DW9807 is a 10 bit DAC from Dongwoon, designed for linear
control of voice coil motor.
This driver creates a V4L2 subdevice and
provides control to set the desired focus.
Signed-off-by: Alan Chiang <alanx.chiang@intel.com>
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The final version of the COMPILE_TEST patch for this driver missed
one warning about suspend/resume functions that can now appear
on platforms that don't always set CONFIG_PM:
drivers/media/platform/omap3isp/isp.c:1008:13: error: 'isp_resume_modules' defined but not used [-Werror=unused-function]
static void isp_resume_modules(struct isp_device *isp)
^~~~~~~~~~~~~~~~~~
drivers/media/platform/omap3isp/isp.c:974:12: error: 'isp_suspend_modules' defined but not used [-Werror=unused-function]
static int isp_suspend_modules(struct isp_device *isp)
This marks the respective functions as __maybe_unused as an easy
workaround.
Fixes: 243131134b ("media: omap3isp: Allow it to build with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set the V4L2_SUBDEV_FL_HAS_DEVNODE flag for the subdevice so that the
subdevice device node is created.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver is going to offer a V4L2 sub-device interface, so
changing the output data format and the frame interval on this sub-device
can be made anytime. However, these requests are preferred to fail while
the video stream on the device is active.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The set_fmt() in subdev pad ops, the s_ctrl() for subdev control handler,
and the s_frame_interval() in subdev video ops could be called when the
device is under power saving mode. These callbacks for ov772x driver
cause updating H/W registers that will fail under power saving mode.
This avoids it by not apply any changes to H/W if the device is not powered
up. Instead the changes will be restored right after power-up.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver provides three V4L2 controls and the current value of
each control is saved as a variable in the private data structure.
We don't need to keep track of the current value by ourself, if we use
v4l2_ctrl returned from v4l2_ctrl_new_std() instead.
This is a preparatory change to avoid accessing registers under power
saving mode. This simplifies s_ctrl() by making it just return without
saving the current control value in private area when it is called under
power saving mode.
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This splits the s_frame_interval() in subdev video ops into selecting the
frame interval and setting up the registers.
This is a preparatory change to avoid accessing registers under power
saving mode.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Depending on the v4l2 driver, calling s_power() could be nested. So the
actual transitions between power saving mode and normal operation mode
should only happen at the first power on and the last power off.
This adds an s_power() nesting counter and updates the power state if the
counter is modified from 0 to != 0 or from != 0 to 0.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver currently only supports legacy platform data probe.
This change enables device tree probing.
Note that the platform data probe can select auto or manual edge control
mode, but the device tree probling can only select auto edge control mode
for now.
[Sakari Ailus: Remove direct OF dependencies from device ID table]
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the ov772x driver obtains a clock with a specific consumer ID.
As there's a single clock for this driver, we could omit clock-names
property in device tree by passing NULL as a consumer ID to clk_get().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver uses "rstb-gpios" and "pwdn-gpios" for reset and
powerdown pins. However, using generic names for these gpios is
preferred. ("reset-gpios" and "powerdown-gpios" respectively)
There is only one mainline user for these gpios, so rename to generic
names.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Create a source pad and set the media controller type to the sensor.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The ov772x driver only works when the i2c controller have
I2C_FUNC_PROTOCOL_MANGLING. However, many i2c controller drivers don't
support it.
The reason that the ov772x requires I2C_FUNC_PROTOCOL_MANGLING is that
it doesn't support repeated starts.
This changes the reading ov772x register method so that it doesn't
require I2C_FUNC_PROTOCOL_MANGLING by calling two separated i2c messages.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support of module being physically mounted upside down.
In this case, mirror and flip are enabled to fix captured images
orientation.
[Sakari Ailus: Use dev_fwnode() instead of accessing device's of_node]
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add HFLIP/VFLIP controls support by setting registers REG21/REG20.
Useless values in hardcoded mode sequences are removed and
remaining binning values are now set after mode sequence being set.
Note that due to BSI (Back Side Illuminated) technology, image capture
is physically mirrored, mirror logic is so inversed in REG21 register
to cancel this effect.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the "rotation" property to tell that the sensor is mounted upside
down. This reverses the behaviour of the VFLIP and HFLIP controls as well
as the pixel order.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The __NEED_MEDIA_LEGACY_API define is 1) ugly and 2) dangerous
since it is all too easy for drivers to define it to get hold of
legacy defines. Instead just define what we need in media-device.c
which is the only place where we need the legacy define
(MEDIA_ENT_T_DEVNODE_UNKNOWN).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts commit 0866df8dff.
The v4l uAPI documentation [0] makes clear that in the case of interlaced
video (i.e: field is V4L2_FIELD_ALTERNATE) the height refers to the number
of lines in the field and not the number of lines in the full frame (which
is twice the field height for interlaced formats).
So the original height calculation was correct, and it shouldn't had been
changed by the mentioned commit.
[0]:https://linuxtv.org/downloads/v4l-dvb-apis/uapi/v4l/subdev-formats.html
Fixes: 0866df8dff ("[media] tvp5150: fix pad format frame height")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Cc: <stable@vger.kernel.org> # for v4.12 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is not required to implement job_ready().
Since this one is dummy, we can drop it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit f1a81afc98 ("[media] m2m: fix bad unlock balance")
removed the last use of v4l2_m2m_ops.lock and
v4l2_m2m_ops.unlock hooks. They are not actually
used anymore. Remove them.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As per the documentation, job_abort is not required
to wait until the current job finishes. It is redundant
to do so, as the core will perform the wait operation.
Remove the wait infrastructure completely.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, rga_buf_start_streaming() is expecting
pm_runtime_get_sync to return zero on success, which
is wrong.
As per the documentation, pm_runtime_get_sync increments
the device's usage counter and return its result.
This means it will typically return a positive integer
on success and a negative error code.
Therefore, rockchip-rga driver is currently unusable
failing to start_streaming in most cases. Fix it and
while here, cleanup the buffer return-to-core logic.
Fixes: f7e7b48e6d ("[media] rockchip/rga: v4l2 m2m support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Jacob Chen <jacob-chen@iotwrt.com>
[hans.verkuil@cisco.com: fix line over 80 cols warning]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When checking a format for validity, the resolution is reset to 1280x720
whenever the pixel format is not supported. This behavior can mislead
user-space into believing that this is the only resolution supported,
and looks strange considering that if we try/set the same format with
just the pixel format changed to a valid one, the call will this time
succeed without altering the resolution.
Resolution is managed independently of the pixel format, so remove this
reset.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When dvb_register_adapter fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling dvb_register_adapter.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
[hans.verkuil@cisco.com: use pr_err and fix typo: adater -> adapter]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When snd_ctl_add fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling snd_ctl_add.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The check for a zero retval is redundant as all paths that lead to
this point have set retval to an error return value that is non-zero.
Remove the redundant check.
Detected by CoverityScan, CID#102589 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there is a schedulable job, v4l2_m2m_try_schedule() calls
v4l2_m2m_try_run(). This makes the unconditional v4l2_m2m_try_run()
called by v4l2_m2m_job_finish superfluous. Remove it.
Fixes: 7f98639def ("V4L/DVB: add memory-to-memory device helper framework for videobuf")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Name is already initialized by assignment from rga_videodev.
Signed-off-by: Anton Leontiev <scileont@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Name is already initialized by assignment from deinterlace_videodev.
Signed-off-by: Anton Leontiev <scileont@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Name is already initialized by assignment from emmaprp_videodev.
Signed-off-by: Anton Leontiev <scileont@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jia-Ju Bai
Matt Ranostay
Niklas Söderlund
Ezequiel Garcia
Hans Verkuil
Nicolas Dufresne
Philipp Zabel
Katsuhiro Suzuki
Kieran Bingham
Guennadi Liakhovetski
Laurent Pinchart
Mauro Carvalho Chehab
Brad Love
Gustavo A. R. Silva
Wolfram Sang
Mika Båtsman
Sean Young
Stanimir Varbanov
Julia Lawall
Krzysztof Ha?asa
Hans Verkuil
Hans Verkuil
Laurent Pinchart
Neil Armstrong
Sakari Ailus
Jacopo Mondi
Todor Tomov
Luca Ceresoli
Hugues Fruchet
Greg Kroah-Hartman
Peter Rosin
Arnd Bergmann
Randy Dunlap
Sylwester Nawrocki
Wolfram Sang
Maciej S. Szmigiero
Keiichi Watanabe
Alexey Khoroshilov
Bingbu Cao
Philipp Puschmann
Akinobu Mita
Javier Martinez Canillas
Alan Chiang
Alexandre Courbot
Zhouyang Jia
Colin Ian King
Anton Leontiev