The mesh forwarding path was not checking that data
frames were protected when running an encrypted network;
add the necessary check.
Cc: stable@vger.kernel.org
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current minstrel_ht rate control behavior is somewhat optimistic in
trying to find optimum TX rate. While this is usually fine for normal
Data frames, there are cases where a more conservative set of retry
parameters would be beneficial to make the connection more robust.
EAPOL frames are critical to the authentication and especially the
EAPOL-Key message 4/4 (the last message in the 4-way handshake) is
important to get through to the AP. If that message is lost, the only
recovery mechanism in many cases is to reassociate with the AP and start
from scratch. This can often be avoided by trying to send the frame with
more conservative rate and/or with more link layer retries.
In most cases, minstrel_ht is currently using the initial EAPOL-Key
frames for probing higher rates and this results in only five link layer
transmission attempts (one at high(ish) MCS and four at MCS0). While
this works with most APs, it looks like there are some deployed APs that
may have issues with the EAPOL frames using HT MCS immediately after
association. Similarly, there may be issues in cases where the signal
strength or radio environment is not good enough to be able to get
frames through even at couple of MCS 0 tries.
The best approach for this would likely to be to reduce the TX rate for
the last rate (3rd rate parameter in the set) to a low basic rate (say,
6 Mbps on 5 GHz and 2 or 5.5 Mbps on 2.4 GHz), but doing that cleanly
requires some more effort. For now, we can start with a simple one-liner
that forces the minimum rate to be used for EAPOL frames similarly how
the TX rate is selected for the IEEE 802.11 Management frames. This does
result in a small extra latency added to the cases where the AP would be
able to receive the higher rate, but taken into account how small number
of EAPOL frames are used, this is likely to be insignificant. A future
optimization in the minstrel_ht design can also allow this patch to be
reverted to get back to the more optimized initial TX rate.
It should also be noted that many drivers that do not use minstrel as
the rate control algorithm are already doing similar workarounds by
forcing the lowest TX rate to be used for EAPOL frames.
Cc: stable@vger.kernel.org
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 06d961a8e2 ("mac80211/minstrel: use the new rate control API")
inverted the condition 'if (msr->sample_limit != 0)' to
'if (!msr->sample_limit != 0)'. But it is confusing both to people and
compilers (gcc5):
net/mac80211/rc80211_minstrel.c: In function 'minstrel_get_rate':
net/mac80211/rc80211_minstrel.c:376:26: warning: logical not is only applied to the left hand side of comparison
if (!msr->sample_limit != 0)
^
Let there be only 'if (!msr->sample_limit)'.
Fixes: 06d961a8e2 ("mac80211/minstrel: use the new rate control API")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
nl80211_exit should be called in cfg80211_init if nl80211_init succeeds
but regulatory_init or create_singlethread_workqueue fails.
Signed-off-by: Junjie Mao <junjie_mao@yeah.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are currently 8 rules in the world_regdom, but only the first 6
are applied due to an incorrect value for n_reg_rules. This causes
channels 149-165 and 60GHz to be disabled.
Signed-off-by: Jason Abele <jason@aether.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If monitor flags parsing results in active monitor but that
isn't supported, the already allocated message is leaked.
Fix this by moving the allocation after this check.
Reported-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently add nested members of the NL80211_ATTR_SCAN_FREQUENCIES
as NLA_U32 attributes of type NL80211_ATTR_WIPHY_FREQ in
cfg80211_net_detect_results. However, since there can be an arbitrary number of
frequency results, we should use the loop index of the loop used to add the
frequency results to NL80211_ATTR_SCAN_FREQUENCIES as the type (i.e. nla_type)
for each result attribute, rather than a fixed type.
This change is in line with how nested members are added to
NL80211_ATTR_SCAN_FREQUENCIES in the functions nl80211_send_wowlan_nd and
nl80211_add_scan_req.
Signed-off-by: Samuel Tan <samueltan@chromium.org>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If ieee80211_vif_use_channel() fails, we have to clear
sdata->radar_required (which we might have just set).
Failing to do it results in stale radar_required field
which prevents starting new scan requests.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Eliad Peller <eliad@wizery.com>
[use false instead of 0]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Correct two problems with the error handling when using the netlink
forwarding API: first, the netlink skb is never freed if nla_put()
fails; and second, genlmsg_unicast() can fail if the netlink socket
is full. In the latter case, the corresponding data skb is not counted
as a drop and userspace programs like wmediumd will see TCP stalls
due to lost packets.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
tcp_should_expand_sndbuf() does not expand the send buffer if we have
filled the congestion window.
However, it should use tcp_packets_in_flight() instead of
tp->packets_out to make this check.
Testing has established that the difference matters a lot if there are
many SACKed packets, causing a needless performance shortfall.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to use burst capability (aka xmit_more) on a virtual device
like bonding is not supported.
For example, skb might be queued multiple times on a qdisc, with
various list corruptions.
Fixes: 38b2cf2982 ("net: pktgen: packet bursting via skb->xmit_more")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are certain regressions which are pointing to
these two commits which we are having a hard time
resolving. So revert them for now.
Specifically this reverts:
commit 0bec3b700d
Author: Florian Westphal <fw@strlen.de>
Date: Wed Jan 7 10:49:49 2015 +0100
r8169: add support for xmit_more
and
commit 1e91887685
Author: Florian Westphal <fw@strlen.de>
Date: Wed Oct 1 13:38:03 2014 +0200
r8169: add support for Byte Queue Limits
There were some attempts by Eric Dumazet to address some obvious
problems in the TX flow, to see if they would fix the problems,
but none of them seem to help for the regression reporters.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.
current->state = TASK_RUNNING is replaced by __set_current_state()
Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-By: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.
Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper function to access current->state.
Direct assignments are prone to races and therefore buggy.
Thanks to Peter Zijlstra for the exact definition of the problem.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets defragmentation was introduced for PACKET_FANOUT_HASH only,
see 7736d33f42 ("packet: Add pre-defragmentation support for ipv4
fanouts")
It may be useful to have defragmentation enabled regardless of
fanout type. Without that, the AF_PACKET user may have to:
1. Collect fragments from different rings
2. Defragment by itself
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct bucket_table contains mostly read fields :
size, locks_mask, locks.
Make sure these are not sharing a cache line with buckets[]
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
colons are used as a separator in netdev device lookup in dev_ioctl.c
Specific functions are SIOCGIFTXQLEN SIOCETHTOOL SIOCSIFNAME
Signed-off-by: Matthew Thode <mthode@mthode.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading 64-bits register was not working because we inverted the steps
between reading the lower 32-bits of the register and reading the upper
32-bits. Swapping these operations is how the HW guarantees that 64-bits
reads are latched correctly. We only have a handful of 64-bits registers
for now, mostly MIB counters, so the imapct is low.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no good reason why to disallow unloading of the rhashtable
test case module.
Commit 9d6dbe1bba moved the code from a boot test into a stand-alone
module, but only converted the subsys_initcall() handler into a
module_init() function without a related exit handler, and thus
preventing the test module from unloading.
Fixes: 9d6dbe1bba ("rhashtable: Make selftest modular")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to allocate future tables via bucket_table_alloc(), it seems
overkill on large table shifts that we probe for kzalloc() unconditionally
first, as it's likely to fail.
Only probe with kzalloc() for more reasonable table sizes and use vzalloc()
either as a fallback on failure or directly in case of large table sizes.
Fixes: 7e1e77636e ("lib: Resizable, Scalable, Concurrent Hash Table")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore pre 54c5b7d311 behaviour and only probe for expansions on inserts
and shrinks on deletes. Currently, it will happen that on initial inserts
into a sparse hash table, we may i.e. shrink it first simply because it's
not fully populated yet, only to later realize that we need to grow again.
This however is counter intuitive, e.g. an initial default size of 64
elements is already small enough, and in case an elements size hint is given
to the hash table by a user, we should avoid unnecessary expansion steps,
so a shrink is clearly unintended here.
Fixes: 54c5b7d311 ("rhashtable: introduce rhashtable_wakeup_worker helper function")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ying Xue <ying.xue@windriver.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains updates for your net tree, they are:
1) Fix removal of destination in IPVS when the new mixed family support
is used, from Alexey Andriyanov via Simon Horman.
2) Fix module refcount undeflow in nft_compat when reusing a match /
target.
3) Fix iptables-restore when the recent match is used with a new hitcount
that exceeds threshold, from Florian Westphal.
4) Fix stack corruption in xt_socket due to using stack storage to save
the inner IPv6 header, from Eric Dumazet.
I'll follow up soon with another batch with more fixes that are still
cooking.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cfpkt_iterate() function can return -EPROTO on error, but the
function is a u16 so the negative value gets truncated to a positive
unsigned short. This causes a static checker warning.
The only caller which might care is cffrml_receive(), when it's checking
the frame checksum. I modified cffrml_receive() so that it never says
-EPROTO is a valid checksum.
Also this isn't ever going to be inlined so I removed the "inline".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue caught by 0-day kernel test infrastructure. Code changed to use sockaddr
members so that %pISc can be used instead.
Fixes: b5a02f503c ('cxgb4 : Update ipv6 address handling api')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit aafb3e98b2 (netdev: introduce new NETIF_F_HW_SWITCH_OFFLOAD feature
flag for switch device offloads) add a new feature without adding it to
netdev_features_strings array; this patch fixes this.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipvlan was added into 3.19 release and iproute2 added support
for the same in iproute2-3.19 package.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With object runtime debugging enabled, the rhashtable test suite
will rightfully throw a warning "ODEBUG: object is on stack, but
not annotated" from rhashtable_init().
This is because run_work is (correctly) being initialized via
INIT_WORK(), and not annotated by INIT_WORK_ONSTACK(). Meaning,
rhashtable_init() is okay as is, we just need to move ht e.g.,
into global scope.
It never triggered anything, since test_rhashtable is rather a
controlled environment and effectively runs to completion, so
that stack memory is not vanishing underneath us, we shouldn't
confuse any testers with it though.
Fixes: 7e1e77636e ("lib: Resizable, Scalable, Concurrent Hash Table")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ltpc driver is rather outdated and does not get built on most
platforms because it requires the ISA_DMA_API symbol. However
there are some ARM platforms that have ISA_DMA_API but no virt_to_bus,
and they get this build error when enabling the ltpc driver.
drivers/net/appletalk/ltpc.c: In function 'handlefc':
drivers/net/appletalk/ltpc.c:380:2: error: implicit declaration of function 'virt_to_bus' [-Werror=implicit-function-declaration]
set_dma_addr(dma,virt_to_bus(ltdmacbuf));
^
This adds another dependency in Kconfig to avoid that configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smc91x driver tries to support multiple platforms at compile
time, but they are mutually exclusive at runtime, and not clearly
defined.
Trying to build for CONFIG_SA1100_ASSABET without CONFIG_ASSABET_NEPONSET
results in this link error:
drivers/built-in.o: In function `smc_drv_probe':
:(.text+0x33310c): undefined reference to `neponset_ncr_frob'
since the neponset_ncr_set function is not defined otherwise.
Similarly, building for both CONFIG_SA1100_ASSABET and CONFIG_SA1100_PLEB
results in a different build error:
smsc/smc91x.c: In function 'smc_drv_probe':
smsc/smc91x.c:2299:2: error: implicit declaration of function 'neponset_ncr_set' [-Werror=implicit-function-declaration]
neponset_ncr_set(NCR_ENET_OSC_EN);
^
smsc/smc91x.c:2299:19: error: 'NCR_ENET_OSC_EN' undeclared (first use in this function)
neponset_ncr_set(NCR_ENET_OSC_EN);
^
This is an attempt to fix the call site responsible for both
errors, making sure we call the function exactly when the driver
is actually trying to run on the assabet/neponset machine. With
this patch, I no longer see randconfig build errors in this file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Non NAPI drivers can call skb_tstamp_tx() and then sock_queue_err_skb()
from hard IRQ context.
Therefore, sock_dequeue_err_skb() needs to block hard irq or
corruptions or hangs can happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 364a9e9324 ("sock: deduplicate errqueue dequeue")
Fixes: cb820f8e4b ("net: Provide a generic socket error queue delivery method for Tx time stamps.")
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gro_remcsum_init() initializes the gro_remcsum.delta member only,
leading to compiler warnings about a possibly uninitialized
gro_remcsum.offset member:
drivers/net/vxlan.c: In function ‘vxlan_gro_receive’:
drivers/net/vxlan.c:602: warning: ‘grc.offset’ may be used uninitialized in this function
net/ipv4/fou.c: In function ‘gue_gro_receive’:
net/ipv4/fou.c:262: warning: ‘grc.offset’ may be used uninitialized in this function
While these are harmless for now:
- skb_gro_remcsum_process() sets offset before changing delta,
- skb_gro_remcsum_cleanup() checks if delta is non-zero before
accessing offset,
it's safer to let the initialization function initialize all members.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If both promisc and allmulti are set, promisc should trump allmulti and
disable the MAC filter; otherwise, the interface is not really promisc.
Previously, this code checked IFF_ALLMULTI prior to and without regard for
IFF_PROMISC; if both were set, only multicast and direct unicast traffic
would make it through the filter.
Signed-off-by: Derrick Pallas <pallas@meraki.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Open vSwitch allows moving internal vport to different namespace
while still connected to the bridge. But when namespace deleted
OVS does not detach these vports, that results in dangling
pointer to netdevice which causes kernel panic as follows.
This issue is fixed by detaching all ovs ports from the deleted
namespace at net-exit.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
IP: [<ffffffffa0aadaa5>] ovs_vport_locate+0x35/0x80 [openvswitch]
Oops: 0000 [#1] SMP
Call Trace:
[<ffffffffa0aa6391>] lookup_vport+0x21/0xd0 [openvswitch]
[<ffffffffa0aa65f9>] ovs_vport_cmd_get+0x59/0xf0 [openvswitch]
[<ffffffff8167e07c>] genl_family_rcv_msg+0x1bc/0x3e0
[<ffffffff8167e319>] genl_rcv_msg+0x79/0xc0
[<ffffffff8167d919>] netlink_rcv_skb+0xb9/0xe0
[<ffffffff8167deac>] genl_rcv+0x2c/0x40
[<ffffffff8167cffd>] netlink_unicast+0x12d/0x1c0
[<ffffffff8167d3da>] netlink_sendmsg+0x34a/0x6b0
[<ffffffff8162e140>] sock_sendmsg+0xa0/0xe0
[<ffffffff8162e5e8>] ___sys_sendmsg+0x408/0x420
[<ffffffff8162f541>] __sys_sendmsg+0x51/0x90
[<ffffffff8162f592>] SyS_sendmsg+0x12/0x20
[<ffffffff81764ee9>] system_call_fastpath+0x12/0x17
Reported-by: Assaf Muller <amuller@redhat.com>
Fixes: 46df7b81454("openvswitch: Add support for network namespaces.")
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Thomas Graf <tgraf@noironetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcf_em_validate(), after calling request_module() to load the
kind-specific module, set em->ops to NULL before returning -EAGAIN, so
that module_put() is not called again by tcf_em_tree_destroy().
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_init_eee uses phy_find_setting(phydev->speed, phydev->duplex)
to find a valid entry in the settings array for the given speed
and duplex value. For full duplex 1000baseT, this will return
the first matching entry, which is the entry for 1000baseKX_Full.
If the phy eee does not support 1000baseKX_Full, this entry will not
match, causing phy_init_eee to fail for no good reason.
Fixes: 9a9c56cb34 ("net: phy: fix a bug when verify the EEE support")
Fixes: 3e7077067e ("phy: Expand phy speed/duplex settings array")
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_copy_bits() returns zero on success and negative value on error,
so it is needed to invert the condition in ip_check_defrag().
Fixes: 1bf3751ec9 ("ipv4: ip_check_defrag must not modify skb before unsharing")
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The National Instruments USB Host-to-Host Cable is based on the Prolific
PL-25A1 chipset. Add its VID/PID so the plusb driver will recognize it.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea creates memory hotplug, reboot and crash hooks even if there
are no adapters in the box. Just create them when we probe our
first adapter.
[cascardo: use ehea_register_memory_hooks return code]
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gnet_stats_copy_app() function gets called, more often than not, with its
second argument a pointer to an automatic variable in the caller's stack.
Therefore, to avoid copying garbage afterwards when calling
gnet_stats_finish_copy(), this data is better copied to a dynamically allocated
memory that gets freed after use.
[xiyou.wangcong@gmail.com: remove a useless kfree()]
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This contains two new drivers, one for Allwinner SoCs and the other for
Imagination Technologies' Pistachio SoC.
Complementing this are a couple of fixes to the Atmel HLCDC PWM and STi
PWM drivers as well as minor cleanups to the core and the Tegra driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJU5EPtAAoJEN0jrNd/PrOhqRcQAJSxA7/HVzyEOSphpmysTwnh
gu1++iaFw0LTJ/OcoA3i6oesmbZ+W0QhEZEflEEXuQriAT/U0scC9sKcxz3iBWc3
T1+S3V8CF3ZXjo9Tuurihf/QsfrwrMwge4CQUZfdpRjgD3yiiFx9+U6NwBNmtYix
C1BhR9ybHU16LUuYWct3iS1kjwW/eGx/FLYuW46dYHjcYrAlMEXCZWFhKbgZpnl7
AF6Wap2CWBrFLuftsz6kXy/w8MMx8jZXoUpWlCOs1bY2xJTjOGjkzijs6fHTv+dU
+AvjoOAzsDVEsi6QYoVrNh6XvjpG/VQuk0DKQ3/OZBrKtRLFsrDD3uB5+yYg5Liv
/b6/vNNL64qKrM8677PzoprjdgInCnN2EFxass4al6l9bC7IxCHRwutz+dKSfBy7
KUqOghl1cQEPxyXly4NGo4Z4pC/S03xmghfBcgdk6yulpEnV/GXPZzzyrikFqcYQ
TY03BP1nJ1fkGN42kYZYkdefUOBzybEAT2q9Zq3SgVoexkgDNa1vKo4NEHbZmjYt
Kz1QT1cz/en2Cp2snLSMPsidgr9YaXB6Lrl6YlLHEtG04f0Ey3/iJpMm9VAy5dEv
fDgavey1OOM5qzMJv0zaK73gE8xFSqD0sV5tbig6IW1KFoICD2+mfgAnjuB17xEm
RbLSMs2uuBJ3N2oO43HR
=3uQb
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains two new drivers, one for Allwinner SoCs and the other
for Imagination Technologies' Pistachio SoC.
Complementing this are a couple of fixes to the Atmel HLCDC PWM and
STi PWM drivers as well as minor cleanups to the core and the Tegra
driver"
* tag 'pwm/for-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: tegra: Use NSEC_PER_SEC
pwm: Remove unnecessary check before of_node_put()
pwm: Add device tree binding document for IMG PWM DAC
pwm: Imagination Technologies PWM DAC driver
pwm: sti: Maintain a bitmap of configured devices
pwm: sunxi: document OF bindings
pwm: Add Allwinner SoC support
pwm: atmel-hlcdc: Prevent division by zero
pwm: atmel-hlcdc: Depend on HAVE_CLK
Pull dmaengine updates from Vinod Koul:
"This update brings:
- the big cleanup up by Maxime for device control and slave
capabilities. This makes the API much cleaner.
- new IMG MDC driver by Andrew
- new Renesas R-Car Gen2 DMA Controller driver by Laurent along with
bunch of fixes on rcar drivers
- odd fixes and updates spread over driver"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (130 commits)
dmaengine: pl330: add DMA_PAUSE feature
dmaengine: pl330: improve pl330_tx_status() function
dmaengine: rcar-dmac: Disable channel 0 when using IOMMU
dmaengine: rcar-dmac: Work around descriptor mode IOMMU errata
dmaengine: rcar-dmac: Allocate hardware descriptors with DMAC device
dmaengine: rcar-dmac: Fix oops due to unintialized list in error ISR
dmaengine: rcar-dmac: Fix spinlock issues in interrupt
dmaenegine: edma: fix sparse warnings
dmaengine: rcar-dmac: Fix uninitialized variable usage
dmaengine: shdmac: extend PM methods
dmaengine: shdmac: use SET_RUNTIME_PM_OPS()
dmaengine: pl330: fix bug that cause start the same descs in cyclic
dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers
dmaengine: at_xdmac: simplify channel configuration stuff
dmaengine: at_xdmac: introduce save_cc field
dmaengine: at_xdmac: wait for in-progress transaction to complete after pausing a channel
ioat: fail self-test if wait_for_completion times out
dmaengine: dw: define DW_DMA_MAX_NR_MASTERS
dmaengine: dw: amend description of dma_dev field
dmatest: move src_off, dst_off, len inside loop
...
Pull watchdog updates from Wim Van Sebroeck:
"This adds the following new drivers:
- ImgTec PDC Watchdog Timer Driver,
- Mediatek SoC integrated watchdog
Add support for BCM5301X, IT8783, NCT6791 and NCT6792 WDT's
Add bcm47xx_wdt and da9063 restart handlers and contains overall
improvements and fixes"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: bcm47xx_wdt.c: allow enabling on BCM5301X arch
watchdog: jz4740: Add DT support
dt: watchdog: Add DT binding documentation for jz4740 watchdog timer
watchdog: dw_wdt: Try to get a 30 second watchdog by default
watchdog: dw_wdt: pat the watchdog before enabling it
watchdog: w83627hf_wdt: Add support for NCT6791 and NCT6792
watchdog: bcm47xx_wdt.c: add restart handler support
watchdog: gpio_wdt: Add "always_running" feature to GPIO watchdog
watchdog: da9063: Add restart handler support
ARM: mediatek: dts: Add bindings for watchdog
watchdog: Add driver for Mediatek watchdog
watchdog: Fix omap watchdogs to enable the magic close bit
watchdog: rt2880_wdt: minor clean up
watchdog: hpwdt: Fix initialization message in hpwdt.c
watchdog: it87_wdt: add IT8783 ID
watchdog: imx2: Constify struct regmap_config and watchdog_ops
DT: watchdog: Add ImgTec PDC Watchdog Timer binding documentation
watchdog: ImgTec PDC Watchdog Timer Driver
- Replace made-up, unallocated Vendor and Model values of firewire-core's
Configuration ROM register root directory by properly registered IDs.
(These IDs are visible to peer nodes on the bus and locally via sysfs,
but they are not involved in protocol matching or driver matching, nor
are they used in stock udev rules.)
- Remove some unneccessary code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qJGA
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull fireware updates from Stefan Richter:
"IEEE 1394 subsystem updates:
- Replace made-up, unallocated Vendor and Model values of
firewire-core's Configuration ROM register root directory by
properly registered IDs. (These IDs are visible to peer nodes on
the bus and locally via sysfs, but they are not involved in
protocol matching or driver matching, nor are they used in stock
udev rules)
- Remove some unneccessary code"
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: core: use correct vendor/model IDs
firewire: sbp2: remove redundant check for bidi command
firewire: ohci: Remove unused function
NAND:
* Add new Hisilicon NAND driver for Hip04
* Add default reboot handler, to ensure all outstanding erase transactions
complete in time
* jz4740: convert to use GPIO descriptor API
* Atmel: add support for sama5d4
* Change default bitflip threshold to 75% of correction strength
* Miscellaneous cleanups and bugfixes
SPI NOR:
* Freescale QuadSPI:
- Fix a few probe() and remove() issues
- Add a MAINTAINERS entry for this driver
- Tweak transfer size to increase read performance
- Add suspend/resume support
* Add Micron quad I/O support
* ST FSM SPI: miscellaneous fixes
JFFS2:
* gracefully handle corrupted 'offset' field found on flash
Other:
* bcm47xxpart: add tweaks for a few new devices
* mtdconcat: set return lengths properly for mtd_write_oob()
* map_ram: enable use with mtdoops
* maps: support fallback to ROM/UBI for write-protected NOR flash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+nRk
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150216' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND:
- Add new Hisilicon NAND driver for Hip04
- Add default reboot handler, to ensure all outstanding erase
transactions complete in time
- jz4740: convert to use GPIO descriptor API
- Atmel: add support for sama5d4
- Change default bitflip threshold to 75% of correction strength
- Miscellaneous cleanups and bugfixes
SPI NOR:
- Freescale QuadSPI:
- Fix a few probe() and remove() issues
- Add a MAINTAINERS entry for this driver
- Tweak transfer size to increase read performance
- Add suspend/resume support
- Add Micron quad I/O support
- ST FSM SPI: miscellaneous fixes
JFFS2:
- gracefully handle corrupted 'offset' field found on flash
Other:
- bcm47xxpart: add tweaks for a few new devices
- mtdconcat: set return lengths properly for mtd_write_oob()
- map_ram: enable use with mtdoops
- maps: support fallback to ROM/UBI for write-protected NOR flash"
* tag 'for-linus-20150216' of git://git.infradead.org/linux-mtd: (46 commits)
mtd: hisilicon: && vs & typo
jffs2: fix handling of corrupted summary length
mtd: hisilicon: add device tree binding documentation
mtd: hisilicon: add a new NAND controller driver for hisilicon hip04 Soc
mtd: avoid registering reboot notifier twice
mtd: concat: set the return lengths properly
mtd: kconfig: replace PPC_OF with PPC
mtd: denali: remove unnecessary stubs
mtd: nand: remove redundant local variable
MAINTAINERS: add maintainer entry for FREESCALE QUAD SPI driver
mtd: fsl-quadspi: improve read performance by increase AHB transfer size
mtd: fsl-quadspi: Remove unnecessary 'map_failed' label
mtd: fsl-quadspi: Remove unneeded success/error messages
mtd: fsl-quadspi: Fix the error paths
mtd: nand: omap: drop condition with no effect
mtd: nand: jz4740: Convert to GPIO descriptor API
mtd: nand: Request strength instead of bytes for soft BCH
mtd: nand: default bitflip-reporting threshold to 75% of correction strength
mtd: atmel_nand: introduce a new compatible string for sama5d4 chip
mtd: atmel_nand: return max bitflips in all sectors in pmecc_correction()
...
Instead of using the literal value for the number of nanoseconds per
second, use the macro instead to increase readability.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Pull networking updates from David Miller:
1) Missing netlink attribute validation in nft_lookup, from Patrick
McHardy.
2) Restrict ipv6 partial checksum handling to UDP, since that's the
only case it works for. From Vlad Yasevich.
3) Clear out silly device table sentinal macros used by SSB and BCMA
drivers. From Joe Perches.
4) Make sure the remote checksum code never creates a situation where
the remote checksum is applied yet the tunneling metadata describing
the remote checksum transformation is still present. Otherwise an
external entity might see this and apply the checksum again. From
Tom Herbert.
5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire.
6) Don't explicitly initialize timer struct fields, use setup_timer()
and mod_timer() instead. From Vaishali Thakkar.
7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi
Nomura.
8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet.
9) Don't potentially perform skb_get() on shared skbs, also from Eric
Dumazet.
10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin
KaFai Lau.
11) Fix merge resolution error between the iov_iter changes in vhost and
some bug fixes that occurred at the same time. From Jason Wang.
12) If rtnl_configure_link() fails we have to perform a call to
->dellink() before unregistering the device. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
net: dsa: Set valid phy interface type
rtnetlink: call ->dellink on failure when ->newlink exists
com20020-pci: add support for eae single card
vhost_net: fix wrong iter offset when setting number of buffers
net: spelling fixes
net/core: Fix warning while make xmldocs caused by dev.c
net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081
ipv6: fix ipv6_cow_metrics for non DST_HOST case
openvswitch: Fix key serialization.
r8152: restore hw settings
hso: fix rx parsing logic when skb allocation fails
tcp: make sure skb is not shared before using skb_get()
bridge: netfilter: Move sysctl-specific error code inside #ifdef
ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc
ipvlan: add a missing __percpu pcpu_stats
tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one()
bgmac: fix device initialization on Northstar SoCs (condition typo)
qlcnic: Delete existing multicast MAC list before adding new
net/mlx5_core: Fix configuration of log_uar_page_sz
sunvnet: don't change gso data on clones
...
yet-another-livelock in raid5, and a problem with write errors
to 4K-block devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1BWV
-----END PGP SIGNATURE-----
Merge tag 'md/3.20-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Three bug md fixes for 3.20
yet-another-livelock in raid5, and a problem with write errors to
4K-block devices"
* tag 'md/3.20-fixes' of git://neil.brown.name/md:
md/raid5: Fix livelock when array is both resyncing and degraded.
md/raid10: round up to bdev_logical_block_size in narrow_write_error.
md/raid1: round up to bdev_logical_block_size in narrow_write_error
not be able to decide that an event should not be logged
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jAUs
-----END PGP SIGNATURE-----
Merge tag 'please-pull-fixmcelog' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull mcelog regression fix from Tony Luck:
"Fix regression - functions on the mce notifier chain should not be
able to decide that an event should not be logged"
* tag 'please-pull-fixmcelog' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
x86/mce: Fix regression. All error records should report via /dev/mcelog
Bob Copeland
Jouni Malinen
Jiri Slaby
Junjie Mao
Jason Abele
Johannes Berg
Samuel Tan
Eliad Peller
Neal Cardwell
Eric Dumazet
David S. Miller
Fabian Frederick
Alexander Drozdov
Matthew Thode
Florian Fainelli
Daniel Borkmann
Dan Carpenter
Anish Bhatt
Rami Rosen
Mahesh Bandewar
Arnd Bergmann
Geert Uytterhoeven
Derrick Pallas
Pravin B Shelar
Ignacy Gawędzki
Guenter Roeck
Ben Shelton
Anton Blanchard
Linus Torvalds
Thierry Reding