GIT_AUTHOR_DATE=1386943312
Add USB IDs for the WinFast DTV Dongle Mini.
Device is tested and works fine under MythTV
Signed-off-by: Robert Backhaus <robbak@robbak.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Latest checkpatch.pl has some new requirements for coding style.
Fix some of those.
* remove Free Software Foundation postal address
* use sizeof(*foo), not sizeof(struct foo)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* remove Free Software Foundation postal address
* add one pair of parenthesis
* use sizeof(*foo), not sizeof(struct foo)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adapter is locked by I2C core already. Use unlocked i2c_transfer()
version __i2c_transfer() to avoid deadlock.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert driver from proprietary DVB driver model to standard I2C
driver model.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Write inittab using reg address auto-increment in order to reduce
I/O a little bit.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reg 0x56 should be programmed to 0x01. Add default to inittab.
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Optimal AGC is highly depended on used RF tuner and due to that
it is already included to chip configuration. However, inittab
has default AGC value, which was later replaced by one from config.
Add also comment to all chip configuration options about default
values and if those are needed to set or not.
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Used synthesizer is very typical integer-N PLL, with configurable
reference frequency divider, output frequency divider and of
course N itself. Most common method to calculate values is first
select output divider, then calculate VCO frequency and finally
calculate PLL N from VCO frequency. Do it that way.
Also make some cleanups for filter logic and signal strength.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DIV_ROUND_CLOSEST does the job and looks better.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Switch standard I2C adapter to muxed I2C adapter.
David reported that I2C adapter implementation caused deadlock.
I discussed with Jean and he suggested to implement it as a
multiplexed i2c adapter because tuner I2C bus could be seen like
own I2C segment.
Reported-by: David Howells <dhowells@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I2C transfer were using dynamic stack allocation. Get rid of it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I2C transfer were using dynamic stack allocation. Get rid of it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
M88TS2022 is DVB-S/S2 RF tuner used usually in conjunction with
Montage M88DS3103 DVB-S/S2 demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
PER/UCB statistics are collected once on each 1 second.
However, it doesn't provide the total number of packets
needed to calculate PER.
Yet, as we know the bit rate, it is possible to estimate
such number. So, do it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On dib8000, the BER statistics are updated on every 1.25e6 bits.
Adjust the code to only update the statistics after having it
done.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On dib8000, the block error count is a monotonic 32 bits register.
With DVBv5 stats, we use a 64 bits counter, that it is reset
when a new channel is tuned.
Change the UCB counting start from 0 and to be returned with
64 bits, just like the API requests.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Use multiple linear segments to better interpolate the dBm
for the signal strength.
The table that converts from linear strength to dB was
empirically determinated with the help of a signal generator
(DTA-2111).
The entries from -35dBm to -22.5dBm were taken using just
the signal generator and the board.
For the entries from -36dBm to -51dBm, a 16 dB tap was used,
in order to extend its range.
Signals below to -51dBm are just linearly interpolated.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Better to have Signal strength in dB.
This takes a very rough estimation for the signal strength,
that was calibrated using a Dektec DTA-2111 Gold RF generator
and a Pixelview dib8076 stick.
It estimates the signal strength using a linear equation where:
- the max is -22.5 dBm, with returns 55953
- the min is -35.0 dBm, with returns 50110
With -22dBm, the signal strengh is returned as 65535.
Unfortunately, the min strength generated with DTA-2111 is
-35dBm.
It should be noticed that approximating it by a linear equation
is not right. I should probably be splitting it into 0.5 dB
linear segments, in order to get a higher precision, just like
it is done on mb86a20s, but that would force me to add some
attenuators, in order to get dB levels below -35dBm, which is,
btw, strong enough to get signal lock.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
The advantage of DVBv5 stats is that it allows adding proper
scales to all measures. use it for this frontend.
This patch adds a basic set of stats, basically cloning what's already
provided by DVBv3 API. Latter patches will improve it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
On ISDB-T, the valid values for interleaving are 0, 1, 2 and 4.
While the first 3 are properly reported, the last one is reported
as 3 instead. Fix it.
Tested with a Dektec DTA-2111 RF generator.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
The logic that detects if auto search mode should be used is too
complex.
Also, it doesn't cover all cases, as the dib8000_tune logic
requires either auto mode or a fully specified manual mode.
So, move it to a separate function and add some extra debug
data to help identifying when it falled back to auto mode,
because the manual settings are invalid.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Both dvbv5-scan and dvbv5-zap tools call FE_GET_PROPERTY inside the
loop that checks for stats. If the frontend doesn't support DVBv5, it
falls back to call the DVBv5 stats APIs(FE_READ_BER, FE_READ_SIGNAL,
FE_READ_SNR and FE_READ_UNCORRECTED_BLOCKS).
A call to FE_GET_PROPERTY makes dvb-frontend core to call get_frontend().
However, due to a race condition on dib8000 between dib8000_get_frontend
and dib8000_tune, if get_frontend occurs too early, it causes the
tune state machine to fail and not get any lock.
This patch adds a workaround code that makes get_frontend() to just
return if none of the frontends have a SYNC. This change fixed the issue
with dvbv5-scan/dvbv5-zap, but a fine-tuned logic might be needed in
the future, when we implement DVBv5 stats on this frontend.
The procedure to test the bug and the fix is the one below:
1) tune into a non-existing frequency with:
$ dvbv5-zap -I dvbv5 -c non_existing_freqs -m 679142857 -t3
2) tune/lock into an existing frequency with:
$ dvbv5-zap -I dvbv5 -c isdb-test -m 479142857
or
$ dvbv5-scan isdb-test
In this case, 679 MHz carrier doesn't exist. Only 479 MHz does.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
As the dvb-frontend kthread can be called anytime, it can race
with some get status ioctl. So, it seems better to avoid one to
race with the other while reading a 32 bits register.
I can't see any other reason for having a mutex there at I2C, except
to provide such kind of protection, as the I2C core already has a
mutex to protect I2C transfers.
Note: instead of this approach, it could eventually remove the dib8000
specific mutex for it, and either group the 4 ops into one xfer or
to manually control the I2C mutex. The main advantage of the current
approach is that the changes are smaller and more puntual.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Commit 173a64cb3f broke support for some dib807x versions.
Fix it by providing backward compatibility with the older versions.
[mkrufky@linuxtv.org: conflict handling and CodingStyle fixes]
Signed-off-by: Olivier Grenie <olivier.grenie@parrot.com>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exynos4x12 has limitations regarding setting chroma subsampling
of an output JPEG image. It cannot be lower than the subsampling
of the raw source image. Also in case of V4L2_JPEG_CHROMA_SUBSAMPLING_GRAY
option the source image fourcc has to be V4L2_PIX_FMT_GREY.
This patch implements try_ctrl callback containing mechanism that
prevents setting invalid value of the V4L2_CID_JPEG_CHROMA_SUBSAMPLING
control.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When output queue fourcc is set to any flavour of YUV,
the V4L2_CID_JPEG_CHROMA_SUBSAMPLING control value as
well as its in-driver cached counterpart have to be
updated with the subsampling property of the format
so as to be able to provide correct information to the
user space and preclude setting an illegal subsampling
mode for Exynos4x12 encoder.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adjust capture format to the Exynos4x12 device limitations,
according to the subsampling value parsed from the source
JPEG image header. If the capture format was set to YUV with
subsampling lower than the one of the source JPEG image
the decoding process would not succeed.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make s5p_jpeg_parse_hdr function capable of parsing
"YCbCr subsampling" field of a jpeg file header. Store the
parsed value in the context.
The information about source JPEG subsampling is required to
make validation of destination format possible, which must be
conducted for exynos4x12 device as the decoding process will
not succeed if the destination format is set to YUV with
subsampling lower than the one of the source JPEG image.
With this knowledge the driver can adjust the destination format
appropriately.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add hardware API for the exynos4x12 on s5p-jpeg.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move function definitions from jpeg-hw.h to jpeg-hw-s5p.c,
add "s5p" prefix and put function declarations in the jpeg-hw-s5p.h.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
You shouldn't use buffers allocated on the stack for USB transfers,
always kmalloc them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DIV_ROUND_UP() is defined in kernel.h which was not included by
media-entity.h. Do exactly that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables. This fixes warnings on platforms where dma_addr_t has a
different size than int.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New chip version, which is very similar than EM28174.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the ISI driver it reads the config register to get original value,
then set the correct FRATE_DIV and YCC_SWAP_MODE directly. This will
cause some bits overlap.
So we need to clear these bits first, then set correct value. This patch
fix it.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ISI_CFG2.YCC_SWAP field controls color component ordering. The
datasheet lists the following orderings for the memory formats.
YCC_SWAP Byte 0 Byte 1 Byte 2 Byte 3
00: Default Cb(i) Y(i) Cr(i) Y(i+1)
01: Mode1 Cr(i) Y(i) Cb(i) Y(i+1)
10: Mode2 Y(i) Cb(i) Y(i+1) Cr(i)
11: Mode3 Y(i) Cr(i) Y(i+1) Cb(i)
This is based on a sensor format set to CbYCrY (UYVY). The driver
hardcodes the output memory format to YUYV, configure the ordering
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ISI_MCK is the sensor master clock. It should be handled by the sensor
driver directly, as the ISI has no use for that clock. Make the clock
optional here while platforms transition to the correct model.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Robert Backhaus
Antti Palosaari
Mauro Carvalho Chehab
Olivier Grenie
Jacek Anaszewski
Hans Verkuil
Sakari Ailus
Malcolm Priestley
Laurent Pinchart
Josh Wu
Laurent Pinchart