When disabling dma channel, a TCF flag is set and as TCIE is enabled, an
interrupt is raised.
On a busy system, the interrupt may have latency and the user can ask for
dmaengine_resume while stm32-dma driver has not yet managed the complete
pause (backup of registers to restore state in resume).
To avoid such a case, instead of waiting the interrupt to backup the
registers, do it just after disabling the channel and discard Transfer
Complete interrupt in case the channel is paused.
Fixes: 099a9a94be ("dmaengine: stm32-dma: add device_pause/device_resume support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20221024083611.132588-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32 MDMA can be triggered by STM32 DMA channels transfer complete.
The "request line number" triggering STM32 MDMA is the STM32 DMAMUX channel
id set by stm32-dmamux driver in dma_spec->args[3].
stm32-dma driver fills the struct stm32_dma_mdma_config used to configure
the MDMA with struct dma_slave_config .peripheral_config/.peripheral_size.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220829154646.29867-6-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Channels 0 to 3 flags are described in DMA_LISR and DMA_LIFCR (L as Low).
Channels 4 to 7 flags are described in DMA_HISR and DMA_HIFCR (H as High).
Macro STM32_DMA_ISR(n) returns the interrupt status register offset for the
channel id (n).
Macro STM32_DMA_IFCR(n) returns the interrupt flag clear register offset
for the channel id (n).
If chan->id % 4 = 2 or 3, then its flags are left-shifted by 16 bits.
If chan->id % 4 = 1 or 3, then its flags are additionally left-shifted by 6
bits.
If chan->id % 4 = 0, then its flags are not shifted.
Macro STM32_DMA_FLAGS_SHIFT(n) returns the required shift to get or set the
channel flags mask.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220829154646.29867-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
At any time, a DMA transfer can be suspended to be restarted later before
the end of the DMA transfer.
In order to restart from the point where the transfer was stopped,
DMA_SxNDTR has to be read after disabling the channel by clearing the EN
bit in DMA_SxCR register, to know the number of data items already
collected.
Peripheral and/or memory addresses have to be updated in order to adjust
the address pointers.
SxNDTR register has to be updated with the remaining number of data items
to be transferred (the value read when the channel was disabled).
Then the channel can be re-enabled to resume the transfer from the point
it was suspended.
If the channel was configured in circular or double-buffer mode, the
circular or double-buffer mode must be disabled before re-enabling the
channel to be able to reconfigure SxNDTR register and re-activate circular
or double-buffer mode on next Transfer Complete interrupt where channel
will be disabled by HW. This is due to the fact that on resume, re-writing
SxNDTR register value updates internal HW auto-reload data counter, and
then it truncates all next transfers after a pause/resume sequence.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220505115611.38845-5-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
dmaengine framework offers device_pause and device_resume ops to pause an
on-going transfer and resume it later.
To avoid any misunderstanding with system sleep pm ops, rename pm ops into
stm32_dma_pm_suspend and stm32_dma_pm_resume.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220505115611.38845-4-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
stm32_dma_handle_chan_done() is called on Transfer Complete interrupt.
As DMA_SxSCR register is read in interrupt handler, pass the value as
parameter of stm32_dma_handle_chan_done(). Also return directly if
chan->desc is null to remove one ident level.
Then, stm32_dma_configure_next_sg() is doing something only if
Double-Buffer Mode (DBM) is enabled, so, check it is enabled prior calling
stm32_dma_configure_next_sg(), to remove one ident level in
stm32_dma_configure_next_sg().
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220505115611.38845-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
chan->next_sg is used to know which transfer will start after the ongoing
one. It is incremented for each new transfer, either on transfer start for
non-cyclic transfers, or on transfer complete interrupt for cyclic
transfers.
For cyclic transfer, when the last item is reached, chan->next_sg must be
reinitialized to the first item.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20220505115611.38845-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some stm32-dma consumers [1] rather use dma_get_slave_caps() to get
max_sg_burst of their DMA channel as dma_get_max_seg_size() is specific to
the DMA controller.
All stm32-dma channels have the same features so, don't need to implement
device_caps ops. Let dma_get_slave_caps() relies on dma_device
configuration.
That's why this patch sets dma_device max_sg_burst to the maximum segment
size, which is the maximum of data items that can be transferred without
software intervention.
[1] https://lore.kernel.org/lkml/20220110103739.118426-1-alain.volmat@foss.st.com/
"media: stm32: dcmi: create a dma scatterlist based on DMA max_sg_burst value"
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Tested-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/20220117091740.11064-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Using the % operator on a 64-bit variable is expensive and can
cause a link failure:
arm-linux-gnueabi-ld: drivers/dma/stm32-dma.o: in function `stm32_dma_get_max_width':
stm32-dma.c:(.text+0x170): undefined reference to `__aeabi_uldivmod'
arm-linux-gnueabi-ld: drivers/dma/stm32-dma.o: in function `stm32_dma_set_xfer_param':
stm32-dma.c:(.text+0x1cd4): undefined reference to `__aeabi_uldivmod'
As we know that we just want to check the alignment in
stm32_dma_get_max_width(), there is no need for a full division, and
using a simple mask is a faster replacement.
Same in stm32_dma_set_xfer_param(), change this to only allow burst
transfers if the address is a multiple of the length.
stm32_dma_get_best_burst just after will take buf_len into account to fix
burst in case of misalignment.
Fixes: b20fd5fa31 ("dmaengine: stm32-dma: fix stm32_dma_get_max_width")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211103153312.41483-1-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Theorically, address pointers used by STM32 DMA must be chosen so as to
ensure that all transfers within a burst block are aligned on the address
boundary equal to the size of the transfer.
If this is always the case for peripheral addresses on STM32, it is not for
memory addresses if the user doesn't respect this alignment constraint.
To avoid a weird behavior of the DMA controller in this case (no error
triggered but data are not transferred as expected), force no burst.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211011094259.315023-4-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
buf_addr parameter of stm32_dma_set_xfer_param function is a dma_addr_t.
We only need to check the remainder of buf_addr/max_width, so, no need to
use do_div and extra u64 addr. Use '%' instead.
Fixes: e0ebdbdcb4 ("dmaengine: stm32-dma: take address into account when computing max width")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211011094259.315023-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To prevent accidental repeated completion, mark pending descriptor
complete in terminate_all. It can be the case when terminate_all is called
while no end of transfer interrupt occurs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211011094259.315023-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
STM32 USART/UART is not managing correctly the default DMA REQ/ACK protocol
leading to possibly lock the DMA stream.
Default protocol consists in maintaining ACK signal up to the removal of
REQuest and the transfer completion.
In case of alternative REQ/ACK protocol, ACK de-assertion does not wait the
removal of the REQuest, but only the transfer completion.
This patch retrieves the need of the alternative protocol through the
device tree, and sets the protocol accordingly.
It also unwrap STM32_DMA_DIRECT_MODE_GET macro definition for consistency
with new STM32_DMA_ALT_ACK_MODE_GET macro definition.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210624093959.142265-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
pm_runtime_get_sync will increment pm usage counter
even it failed. Forgetting to putting operation will
result in reference leak here. We fix it by replacing
it with pm_runtime_resume_and_get to keep usage counter
balanced.
Fixes: 48bc73ba14 ("dmaengine: stm32-dma: Add PM Runtime support")
Fixes: 05f8740a0e ("dmaengine: stm32-dma: add suspend/resume power management support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20210607064640.121394-2-zhangqilong3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DMA_SxPAR or DMA_SxM0AR/M1AR registers have to be aligned on PSIZE or MSIZE
respectively. This means that bus width needs to be forced to 1 byte when
computed width is not aligned with address.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-4-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When dma_channel_release is called, it means that the channel won't be used
anymore with the configuration it had. To ensure a future client can safely
use the channel after it has been released, clean the configuration done
when channel was requested.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-3-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To better understand error that can be detected by the DMA controller,
manage the error flags before the transfer flags.
This way, it is possible to know if the FIFO error flag is set for an
over/underrun condition or a FIFO level error.
When a FIFO over/underrun condition occurs, the data is not lost because
peripheral request is not acknowledged by the stream until the over/
underrun condition is cleared. If this acknowledge takes too much time,
the peripheral itself may detect an over/underrun condition of its internal
buffer and data might be lost.
That's why in case the FIFO error flag is set, we check if the channel is
disabled or not, and if a Transfer Complete flag is set, which means that
the channel is disabled because of the end of transfer.
Because channel is disabled by hardware either by a FIFO level error, or by
an end of transfer.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-2-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200828152637.16903-2-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Direct mode or FIFO mode is computed by stm32-dma driver. Add a way for
the user to force direct mode, by setting bit 2 in the bitfield value
specifying DMA features in the device tree.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200422102904.1448-3-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To avoid race with vchan_complete, use the race free way to terminate
running transfer.
Move vdesc->node list_del in stm32_dma_start_transfer instead of in
stm32_mdma_chan_complete to avoid another race in vchan_dma_desc_free_list.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200129153628.29329-9-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch fixes BUG: sleeping function called from invalid context in
stm32_dma_disable_chan function.
The goal of this function is to force channel disable if it has not been
disabled by hardware. This consists in clearing STM32_DMA_SCR_EN bit and
read it as 0 to ensure the channel is well disabled and the last transfer
is over.
In previous implementation, the waiting loop was based on a do...while (1)
with a call to cond_resched to give the scheduler a chance to run a higher
priority process.
But in some conditions, stm32_dma_disable_chan can be called while
preemption is disabled, on a stm32_dma_stop call for example. So
cond_resched must not be used.
To avoid this, use readl_relaxed_poll_timeout_atomic to poll
STM32_DMA_SCR_EN bit cleared.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200129153628.29329-8-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds dma_set_max_seg_size to define sg dma constraint.
This constraint may be taken into account by client to scatter/gather
its buffer.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200129153628.29329-6-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Change STM32 DMA driver to defer its probe operation when reset
controller is expected but has not been probed yet when DMA
device is probed.
Changes error traces when failing to get a system resource so that
it is not printed on failure with deferred probing.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200129153628.29329-4-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove reset controller reference from device instance since it is
used only at probe time.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200129153628.29329-3-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct stm32_dma_desc {
...
struct stm32_dma_sg_req sg_req[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following function:
static struct stm32_dma_desc *stm32_dma_alloc_desc(u32 num_sgs)
{
return kzalloc(sizeof(struct stm32_dma_desc) +
sizeof(struct stm32_dma_sg_req) * num_sgs, GFP_NOWAIT);
}
with:
kzalloc(struct_size(desc, sg_req, num_sgs), GFP_NOWAIT)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190830161423.GA3483@embeddedor
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-11-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Add support in dmaengine core to do device node checks for DT devices and
update bunch of drivers to use that and remove open coding from drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
-----BEGIN PGP SIGNATURE-----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=R+aC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Add support in dmaengine core to do device node checks for DT devices
and update bunch of drivers to use that and remove open coding from
drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
* tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: Revert "dmaengine: fsl-edma: add i.mx7ulp edma2 version support"
dmaengine: at_xdmac: check for non-empty xfers_list before invoking callback
Documentation: dmaengine: clean up description of dmatest usage
dmaengine: tegra210-adma: remove PM_CLK dependency
dmaengine: fsl-edma: add i.mx7ulp edma2 version support
dt-bindings: dma: fsl-edma: add new i.mx7ulp-edma
dmaengine: fsl-edma-common: version check for v2 instead
dmaengine: fsl-edma-common: move dmamux register to another single function
dmaengine: fsl-edma: add drvdata for fsl-edma
dmaengine: Revert "dmaengine: fsl-edma: support little endian for edma driver"
dmaengine: rcar-dmac: Reject zero-length slave DMA requests
dmaengine: dw: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw-edma: fix semicolon.cocci warnings
dmaengine: sh: usb-dmac: Use [] to denote a flexible array member
dmaengine: dmatest: timeout value of -1 should specify infinite wait
dmaengine: dw: Distinguish ->remove() between DW and iDMA 32-bit
dmaengine: fsl-edma: support little endian for edma driver
dmaengine: hsu: Revert "set HSU_CH_MTSR to memory width"
dmagengine: pl330: add code to get reset property
dt-bindings: pl330: document the optional resets property
...
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c6504be539 ("dmaengine: stm32-dma: Fix unsigned variable compared
with zero") duplicated the call to platform_get_irq.
So remove the first call to platform_get_irq.
Fixes: c6504be539 ("dmaengine: stm32-dma: Fix unsigned variable compared with zero")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In double buffer mode, during residue calculation, the DMA can
automatically switch to the next transfer. Indeed the CT bit that
gives position in the double buffer can has been updated by the
hardware, during calculation.
In this case the SxNDTR register value can not be trusted.
If a transition is detected we consider that the DMA has switched to
the beginning of next sg.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit f4fd2ec08f17: ("dmaengine: stm32-dma: use platform_get_irq()") used
unsigned variable irq to store the results and check later for negative
errors, so update the code to use signed variable for this
Fixes: f4fd2ec08f ("dmaengine: stm32-dma: use platform_get_irq()")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ) is not recommended for
requesting IRQ's resources, as they can be not ready yet. Using
platform_get_irq() instead is preferred for getting IRQ even if it was
not retrieved earlier.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For avoiding false FIFO detection, check FIFO Error interrupt is
enabled prior raising any errors.
This will prevent having spurious FIFO error where it shouldn't.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a period length is not multiple of FIFO some data may be stuck
within FIFO.
Burst/FIFO Threshold/Period or buffer length check has to be hardened
In any case DMA will grant any request from client but will degraded
any parameters whether awkward.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The format specifier "%p" can leak kernel addresses.
Use "%pK" instead.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
A single register of the controller holds the information for four dma
channels.
The functions stm32_dma_irq_status() don't mask the relevant bits after
the shift, thus adjacent channel's status is also reported in the returned
value.
Fixed by masking the value before returning it.
Similarly, the function stm32_dma_irq_clear() don't mask the input value
before shifting it, thus an incorrect input value could disable the
interrupts of adjacent channels.
Fixed by masking the input value before using it.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Having 0 in item counter register is valid and stands for a "No or Ended
transfer". Therefore valid transfer starts from @+0 to @+0xFFFE leading to
unaligned scatter gather at boundary. Thus it's safer to round down this
value on its FIFO size (16 Bytes).
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Update the way Transfer Complete and Half Transfer Complete status are
acknowledge. Even if HTI is not enabled its status is shown when reading
registers, driver has to clear it gently and not raise an error.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch improves memory burst capability using best burst size
according to transferred buffer size from/to memory.
>From now on, memory burst is not necessarily same as with peripheral
burst one and fifo threshold is directly managed by this driver in order
to fit with computed memory burst.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When in cyclic mode, the configuration is updated after having started the
DMA hardware (STM32_DMA_SCR_EN) leading to incomplete configuration of
SMxAR registers.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
>From now on, DMA bitfield is to manage DMA FIFO Threshold.
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Trivial fix to spelling mistake and make channel plural.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pcdH
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers"
* tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
async_tx: deprecate broken support for channel switching
dmaengine: rcar-dmac: Widen DMA mask to 40 bits
dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
dmaengine: Provide a wrapper for memcpy operations
dmaengine: zx: fix build warning
dmaengine: dw: we do support Merrifield SoC in PCI mode
dmaengine: dw: add support of iDMA 32-bit hardware
dmaengine: dw: introduce register mappings for iDMA 32-bit
dmaengine: dw: introduce block2bytes() and bytes2block()
dmaengine: dw: extract dwc_chan_pause() for future use
dmaengine: dw: replace convert_burst() with one liner
dmaengine: dw: register IRQ and DMA pool with instance ID
dmaengine: dw: Fix data corruption in large device to memory transfers
dmaengine: ste_dma40: indicate granularity on channels
dmaengine: ste_dma40: indicate directions on channels
dmaengine: stm32-dma: Add error messages if xlate fails
dmaengine: dw: pci: remove LPE Audio DMA ID
dmaengine: stm32-dma: Add max_burst support
dmaengine: stm32-dma: Add synchronization support
dmaengine: stm32-dma: Fix residue computation issue in cyclic mode
...
Amelie Delaunay
Arnd Bergmann
Vinod Koul
Zhang Qilong
Amelie Delaunay
Krzysztof Kozlowski
Pierre-Yves MORDRET
Etienne Carriere
Gustavo A. R. Silva
Stephen Boyd
Linus Torvalds
Thomas Gleixner
Arnaud Pouliquen
Fabien Dessenne
Benjamin Gaignard
Colin Ian King