Impact: fix for PowerPC 32 code
There were some early init code that was not safe for static
ftrace to boot on my PowerBook. This code must only use relative
addressing, and static mcount performs a compare of the
ftrace_trace_function pointer, and gets that with an absolute address.
In the early init boot up code, this will cause a fault.
This patch removes tracing from the files containing the offending
functions.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clean up
Paul Mackerras pointed out that the code to determine if the branch
can reach the destination is incorrect. Michael Ellerman suggested
to pull out the code from create_branch and use that.
Simply using create_branch is probably the best.
Reported-by: Michael Ellerman <michael@ellerman.id.au>
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix to PowerPC code modification
After modifying code it is essential to flush the icache. This patch
adds the missing flush.
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clean up and robustness addition
This patch addresses the comments made by Paul Mackerras.
It removes the type casting between unsigned int and unsigned char
pointers, and replaces them with a use of all unsigned int.
Verification that the jump is indeed made to a trampoline has also
been added.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: quicken mcount calls that are not replaced by dyn ftrace
Dynamic ftrace no longer does on the fly recording of mcount locations.
The mcount locations are now found at compile time. The mcount
function no longer needs to store registers and call a stub function.
It can now just simply return.
Since there are some functions that do not get converted to a nop
(.init sections and other code that may disappear), this patch should
help speed up that code.
Also, the stub for mcount on PowerPC 32 can not be a simple branch
link register like it is on PowerPC 64. According to the ABI specification:
"The _mcount routine is required to restore the link register from
the stack so that the profiling code can be inserted transparently,
whether or not the profiled function saves the link register itself."
This means that we must restore the link register that was used
to make the call to mcount. The minimal mcount function for PPC32
ends up being:
mcount:
mflr r0
mtctr r0
lwz r0, 4(r1)
mtlr r0
bctr
Where we move the link register used to call mcount into the
ctr register, and then restore the link register from the stack.
Then we use the ctr register to jump back to the mcount caller.
The r0 register is free for us to use.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mathieu Desnoyers reported this build failure on powerpc:
kernel/sched.c: In function 'sd_init_NODE':
kernel/sched.c:7319: error: non-static initialization of a flexible array member
kernel/sched.c:7319: error: (near initialization for '(anonymous)')
this happens because .span changed to cpumask_var_t, hence
the static CPU_MASK_NONE initializers in the SD_*_INIT
templates are not type-correct anymore.
Remove them, as they default to empty anyway.
Also remove them from IA64, MIPS and SH.
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When the VM exits, we must call put_page() for every page referenced in the
shadow TLB.
Without this patch, we usually leak 30-50 host pages (120 - 200 KiB with 4 KiB
pages). The maximum number of pages leaked is the size of our shadow TLB, 64
pages.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently, we can end up in an infinite loop if we get a signal
while the kernel has faulted in spufs_ps_fault. Eg:
alarm(1);
write(fd, some_spu_psmap_register_address, 4);
- the write's copy_from_user will fault on the ps mapping, and
signal_pending will be non-zero. Because returning from the fault
handler will never clear TIF_SIGPENDING, so we'll just keep faulting,
resulting in an unkillable process using 100% of CPU.
This change returns VM_FAULT_SIGBUS if there's a fatal signal pending,
letting us escape the loop.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Impact: add ability to trace modules on 32 bit PowerPC
This patch performs the necessary trampoline calls to handle
modules with dynamic ftrace on 32 bit PowerPC.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Impact: Allow 64 bit PowerPC to trace modules with dynamic ftrace
This adds code to handle the PPC64 module trampolines, and allows for
PPC64 to use dynamic ftrace.
Thanks to Paul Mackerras for these updates:
- fix the mod and rec->arch.mod NULL checks.
- fix to is_bl_op compare.
Thanks to Milton Miller for:
- finding the nasty race with using two nops, and recommending
instead that I use a branch 8 forward.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Impact: use cleaner probe_kernel API over assembly
Using probe_kernel_read/write interface is a much cleaner approach
than the current assembly version.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Impact: update to PowerPC ftrace arch API
This patch converts PowerPC to use the new dynamic ftrace arch API.
Thanks to Paul Mackennas for pointing out the mistakes of my original
test_24bit_addr function.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Impact: fix for irq off latency tracer
When idle is called, interrupts are disabled, but the idle function
will still wake up on an interrupt. The problem is that the interrupt
disabled latency tracer will take this call to idle as a latency.
This patch disables the latency tracing when going into idle.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
ethernet0 (called FSL UEC0 in U-Boot) should be enet1 (UCC3/eth1), and
ethernet1 should be enet0 (UCC2/eth0), to be consistent with U-Boot so
that the interfaces do not swap addresses when control passes from
U-Boot to the kernel.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Marvell PHY driver is currently being used for the 88E1111 on the
SBC610. This driver is causing the link to run in 10/Half mode, the generic
PHY driver is correctly configuring the PHY as 1000/Full.
Edit default config to use generic PHY driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It's 1MB, not 512KB. Newer U-Boots will fix this entry, but that's no
reason to have the wrong value in the dts.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPIC has 4 ipis, so it can use the new smp_request_message_ipi to
reduce pathlength when receiving an ipi.
This has the side effect of using the common ipi names, and also
continuing to try request the remaining messages when one fails.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With the new generic smp call function helpers, I noticed the code in
smp_message_recv was a single function call in many cases. While
getting the message number from the ipi data is easy, we can reduce
the path length by a function and data-dependent switch by registering
seperate IPI actions for these simple calls.
Originally I left the ipi action array exposed, but then I realized the
registration code should be common too.
The three users each had their own name array, so I made a fourth
to convert all users to use a common one.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Linux will report the number of page-ins so that the hypervisor can
better determine partition memory pressure. The hardware page size
and the OS page size can be different. In the case where the hardware
page size is 4k and the OS is running with 64k pages the code in
commit 409001948d ("powerpc: Update
page-in counter for CMM") would under-report the number of pages.
This corrects the reporting to the hypervisor by incrementing the
page_in count by 1 << PAGE_FACTOR each time.
Reported-by: Andrew Theurer <habanero@linux.vnet.ibm.com>
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements an optimised mutex fastpath for powerpc, making use of
acquire and release barrier semantics. This takes the mutex
lock+unlock benchmark from 203 to 173 cycles on a G5.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After commit 598056d5af ("[POWERPC] Fix
rmb to order cacheable vs. noncacheable"), rmb() becomes a sync
instruction, which is needed to order cacheable vs noncacheable loads.
However smp_rmb() is #defined to rmb(), and smp_rmb() can be an
lwsync.
This restores smp_rmb() performance by using lwsync there and updates
the comments.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change 2d1b202762 ("powerpc: Fixup
lwsync at runtime") removed __SUBARCH_HAS_LWSYNC, causing smp_wmb to
revert back to eieio for all CPUs. This restores the behaviour
intorduced in 74f0609526 ("powerpc:
Optimise smp_wmb on 64-bit processors").
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In exactly the same way that we updated memcpy() with new feature
sections in commit 25d6e2d7c5 ("powerpc:
Update 64bit memcpy() using CPU_FTR_UNALIGNED_LD_STD"), we do the same
thing here for __copy_tofrom_user(). Once again this is purely a
performance tweak for Cell and Power6 - this has no effect on all the
other 64bit powerpc chips.
We can make these same changes to __copy_tofrom_user() because the
basic copy algorithm is the same as in memcpy() - this version just
has all the exception handling logic needed when copying to or from
userspace as well as a special case for copying whole 4K pages that
are page aligned.
CPU_FTR_UNALIGNED_LD_STD CPU was added in commit
4ec577a289 ("powerpc: Add new CPU
feature: CPU_FTR_UNALIGNED_LD_STD").
We also make the same simple one line change from cmpldi r1,... to
cmpldi cr1,... for consistency.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I can't tell why this WARN_ON exists, and there's no comment
explaining it. Whether the pmd is present or not, pte_alloc_kernel()
seems to handle both cases.
Booting a 440 kernel with 64K PAGE_SIZE triggers the warning, but boot
successfully completes and I see no problems beyond that.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have several instances of inline assembly code that use the addic
or addic. instructions, but don't include XER in the list of clobbers.
The addic and addic. instructions affect the carry bit, which is in
the XER register.
This adds "xer" to the list of clobbers for those inline asm
statements that use addic or addic. and didn't already have it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Introduce ps3_gpu_mutex to synchronizes GPU-related operations, like:
- invoking the L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT command using the
lv1_gpu_context_attribute() hypervisor call,
- handling the PS3AV_CID_AVB_PARAM packet in the PS3 A/V Settings driver.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Various printk format string in code used by the Xilinx Virtex platform
are not 32-bit/64-bit safe. Add correct casting to fix the bugs.
Reported-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Without this patch it is possible to select drivers which require
bestcomm support without bestcomm support being selected. This
patch reworks the bestcomm dependencies to ensure the correct
bestcomm tasks are always enabled.
Reported-by: Hans Lehmann <hans.lehmann@ritter-elektronik.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Conflicts:
security/keys/internal.h
security/keys/process_keys.c
security/keys/request_key.c
Fixed conflicts above by using the non 'tsk' versions.
Signed-off-by: James Morris <jmorris@namei.org>
Pass credentials through dentry_open() so that the COW creds patch can have
SELinux's flush_unauthorized_files() pass the appropriate creds back to itself
when it opens its null chardev.
The security_dentry_open() call also now takes a creds pointer, as does the
dentry_open hook in struct security_operations.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: James Morris <jmorris@namei.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: James Morris <jmorris@namei.org>
Those cores use the 440A type machine check (ie, they have
MCSRR0/MCSRR1). They thus need to call the appropriate fixup
function to hook the right variant of the exception.
Without this, all machine checks become fatal due to loss
of context when entering the exception handler.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
If the size of DRAM is not an exact power of two, we may not have
covered DRAM in its entirety with large 16 and 4 MiB pages. If that
is the case, we can get non-recoverable page faults when doing the
final PTE mappings for the non-large page PTEs.
Consequently, we restrict the top end of DRAM currently allocable
by updating '__initial_memory_limit_addr' so that calls to the LMB to
allocate PTEs for "tail" coverage with normal-sized pages (or other
reasons) do not attempt to allocate outside the allowed range.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Turned off CONFIG_PCI_LEGACY and turned on EXT4, and otherwise mostly
took the defaults. This also updates ppc6xx_defconfig, which covers
the 6xx/7xx/7xxx-based embedded boards.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new context may not be 16-byte aligned, so the real address of the
mcontext structure should be read from the uc_regs pointer instead of
directly using the (unaligned) uc_mcontext field.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Impact: cleanup, change .config option name
We had this ugly config name for a long time for hysteric raisons.
Rename it to a saner name.
We still cannot get rid of it completely, until /proc/<pid>/stack
usage replaces WCHAN usage for good.
We'll be able to do that in the v2.6.29/v2.6.30 timeframe.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
unset CONFIG_PCI_LEGACY in the defconfigs as none of them enable
ISDN drivers which seem to be the only place we are using pci_find_device
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fixes following build error:
CC drivers/usb/gadget/fsl_qe_udc.o
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eprx_stall_change':
drivers/usb/gadget/fsl_qe_udc.c:156: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c:163: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eptx_stall_change':
drivers/usb/gadget/fsl_qe_udc.c:173: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c:180: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eprx_nack':
drivers/usb/gadget/fsl_qe_udc.c:201: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c:201: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eprx_normal':
drivers/usb/gadget/fsl_qe_udc.c:218: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c:218: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_ep_reset':
drivers/usb/gadget/fsl_qe_udc.c:325: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c:342: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_ep_register_init':
drivers/usb/gadget/fsl_qe_udc.c:515: error: 'struct usb_ctlr' has no member named 'usb_usep'
drivers/usb/gadget/fsl_qe_udc.c: In function 'ch9getstatus':
drivers/usb/gadget/fsl_qe_udc.c:1981: error: 'struct usb_ctlr' has no member named 'usb_usep'
make[2]: *** [drivers/usb/gadget/fsl_qe_udc.o] Error 1
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch corrects the bus-frequency value provided in the SBC610's dts.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
David Gibson suggested that since we are now unconditionally copying
the dtb into a malloc()ed buffer, it would be sensible to add a little
padding to the buffer at that point, so that further device tree
manipulations won't need to reallocate it.
This implements that suggestion.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Andrew Morton suggested that using a macro that makes an array
reference look like a function call makes it harder to understand the
code.
This therefore removes the huge_pgtable_cache(psize) macro and
replaces its uses with pgtable_cache[HUGE_PGTABLE_INDEX(psize)].
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Free dynamically allocated device data structures when device registration
fails. This fixes memory leakage when the registration fails.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we started using the generic timekeeping code, we haven't had a
powerpc-specific version of do_gettimeofday, and hence there is now
nothing that reads the do_gtod variable in arch/powerpc/kernel/time.c.
This therefore removes it and the code that sets it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently the clock_gettime implementation in the VDSO produces a
result with microsecond resolution for the cases that are handled
without a system call, i.e. CLOCK_REALTIME and CLOCK_MONOTONIC. The
nanoseconds field of the result is obtained by computing a
microseconds value and multiplying by 1000.
This changes the code in the VDSO to do the computation for
clock_gettime with nanosecond resolution. That means that the
resolution of the result will ultimately depend on the timebase
frequency.
Because the timestamp in the VDSO datapage (stamp_xsec, the real time
corresponding to the timebase count in tb_orig_stamp) is in units of
2^-20 seconds, it doesn't have sufficient resolution for computing a
result with nanosecond resolution. Therefore this adds a copy of
xtime to the VDSO datapage and updates it in update_gtod() along with
the other time-related fields.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that all of the remaining dma_mapping_ops have had their
map_/unmap_single functions updated to become map/unmap_page
functions, there is no need to have the map_/unmap_single function
pointers in the dma_mapping_ops.
So, this removes them and also removes the code that does the checking
for which set of functions to use.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This does a few cosmetic cleanups, moving a couple of things around
but without actually changing what the code does.
(There is a minor change in ordering of operations in
pcibios_setup_bus_devices but it should have no impact).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pseries PCI hotplug code has a number of issues, ranging from
incorrect resource setup to crashes, depending on what is added,
when, whether it contains a bridge, etc etc....
This fixes a whole bunch of these, while actually simplifying the code
a bit, using more generic code in the process and factoring out common
code between adding of a PHB, a slot or a device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To properly fix PCI hotplug, it's useful to be able to make the fixup
passes on all devices whether they were just hot plugged or already
there.
However, pcibios_allocate_bus_resources() wouldn't cope well with
being called twice for a given bus. This makes it ignore resources
that have already been allocated, along with adding a bit of debug
output.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To properly fix PCI hotplug, it's useful to be able to make the fixup
passes on all devices whether they were just hot plugged or already
there.
The EEH code however used to not be very friendly with calling
eeh_add_device_late() multiple time, and not very rebust in the way it
generally tests whether a device is in the expected state vs. the EEH
code.
This improves it, along with cleaning up a couple of debug printk's.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, our PCI code uses the pcibios_fixup_bus() callback, which
is called by the generic code when probing PCI buses, for two
different things.
One is to set up things related to the bus itself, such as reading
bridge resources for P2P bridges, fixing them up, or setting up the
iommu's associated with bridges on some platforms.
The other is some setup for each individual device under that bridge,
mostly setting up DMA mappings and interrupts.
The problem is that this approach doesn't work well with PCI hotplug
when an existing bus is re-probed for new children. We fix this
problem by splitting pcibios_fixup_bus into two routines:
pcibios_setup_bus_self() is now called to setup the bus itself
pcibios_setup_bus_devices() is now called to setup devices
pcibios_fixup_bus() is then modified to call these two after reading the
bridge bases, and the OF based PCI probe is modified to avoid calling
into the first one when rescanning an existing bridge.
[paulus@samba.org - fixed eeh.h for 32-bit compile now that pci-common.c
is including it unconditionally.]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The function pcibios_do_bus_setup() was used by pcibios_fixup_bus()
to perform setup that is different between the 32-bit and 64-bit
code. This difference no longer exists, thus the function is removed
and the setup now done directly from pci-common.c.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit and 64-bit powerpc PCI code used to set up the resource
pointers of the root bus of a given PHB in completely different
places.
This unifies this in large part, by making 32-bit use a routine very
similar to what 64-bit does when initially scanning the PCI busses.
The actual setup of the PHB resources itself is then moved to a
common function in pci-common.c.
This should cause no functional change on 64-bit. On 32-bit, the
effect is that the PHB resources are going to be setup a bit earlier,
instead of being setup from pcibios_fixup_bus().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes the various DBG() macro from the powerpc PCI code and
makes it use the standard pr_debug instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update memcpy() to add two new feature sections: one for aligning the
destination before copying and one for copying using aligned load
and store doubles.
These new feature sections will only affect Power6 and Cell because
the CPU feature bit was only added to these two processors.
Power6 gets its best performance in memcpy() when aligning neither the
source nor the destination, while Cell gets its best performance when
just the destination is aligned. But in order to save on CPU feature
bits we can use the previously added CPU_FTR_CP_USE_DCBTZ feature bit
to differentiate between Power6 and Cell (because CPU_FTR_CP_USE_DCBTZ
was added to Cell but not Power6).
The first feature section acts to nop out the branch that takes us to
the code that aligns us to an eight byte boundary for the destination.
We only want to nop out this branch on Power6.
So the ALT_FTR_SECTION_END() for this feature section creates a test
mask of the two feature bits ORed together and provides an expected
result of just CPU_FTR_UNALIGNED_LD_STD, thus we nop out the branch
if we're on a CPU that has CPU_FTR_UNALIGNED_LD_STD set and
CPU_FTR_CP_USE_DCBTZ unset.
For the second feature section added, if we're on a CPU that has the
CPU_FTR_UNALIGNED_LD_STD bit set then we don't want to do the copy
with aligned loads and stores (and the appropriate shifting left and
right instructions), so we want to nop out the branch to
.Lsrc_unaligned.
The andi. used for this branch is moved to just above the branch
because this allows us to nop out both instructions with just one
feature section which gives us better performance and doesn't hurt
readability which two separate feature sections did.
Moving the andi. to just above the branch doesn't have any noticeable
negative effect on the remaining 64bit processors (the ones that
didn't have this feature bit added).
On Cell this simple modification results in an improvement to measured
memcpy() bandwidth of up to 50% in the hot cache case and up to 15% in
the cold cache case.
On Power6 we get memory bandwidth results that are up to three times
faster in the hot cache case and up to 50% faster in the cold cache
case.
Commit 2a9294369b ("powerpc: Add new CPU
feature: CPU_FTR_CP_USE_DCBTZ") was where CPU_FTR_CP_USE_DCBTZ was
added.
To say that Cell gets its best performance in memcpy() with just the
destination aligned is true but only for the reason that the indirect
shift and rotate instructions, sld and srd, are microcoded on Cell.
This means that either the destination or the source can be aligned,
but not both, and seeing as we get better performance with the
destination aligned we choose this option.
While we're at it make a one line change from cmpldi r1,... to
cmpldi cr1,... for consistency.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a new CPU feature bit, CPU_FTR_UNALIGNED_LD_STD, to be added
to the 64bit powerpc chips that can do unaligned load double and
store double without any performance hit.
This is added to Power6 and Cell and will be used in the next commit
to disable the code that gets the destination address aligned on
those CPUs where doing that doesn't improve performance.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A new field has been added to the VPA as a method for the client OS to
communicate to firmware the number of page-ins it is performing when
running collaborative memory overcommit. The hypervisor will use this
information to better determine if a partition is experiencing memory
pressure and needs more memory allocated to it.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 'ibm,interrupt-server#-size' properties are not in the cpu nodes,
which is where we currently look for them, but rather live under the
interrupt source controller nodes (which have "ibm,ppc-xics" in their
compatible property).
This moves the code that looks for the ibm,interrupt-server#-size
properties from xics_update_irq_servers() into xics_init_IRQ().
Also this adds a check for mismatched sizes across the interrupt
source controller nodes. Not sure this is necessary as in this case
the firmware might be seriously busted.
This property only appears on POWER6 boxes and is only used in the
set-indicator(gqirm) call, and apparently firmware currently ignores
the value we pass. Nevertheless we need to fix it in case future
firmware versions use it.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't want to encourage the device_type usage. It isn't used in
the code, so we can simply remove it from the dts files.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When no hardware method is provided to sync the timebase registers
across the machine, and the platform doesn't sync them for us, then we
use a generic software implementation. Currently, the code for that
has many printks, and they don't have log levels. Most of the printks
are only useful for debugging the code, and since we haven't had any
problems with it for years, this turns them into pr_debug.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code to properly expose domain numbers in /proc is somewhat
bogus on ppc64 as it depends on the "buid" field being non-0,
but that field is really pseries specific.
This removes that code and makes ppc64 use the same code as 32-bit
which effectively decides whether to expose domains based on
ppc_pci_flags set by the platform, and sets the default for 64-bit
to enable domains and enable compatibility for domain 0 (which
strips the domain number for domain 0 to help with X servers).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This gets rid of this build warning:
arch/powerpc/platforms/pseries/pci_dlpar.c: In function 'init_phb_dynamic':
arch/powerpc/platforms/pseries/pci_dlpar.c:192: warning: unused variable 'b'
This is one of the very few warnings left in a ppc64_defconfig build and
getting rid of it will make it easier to see future introduced ones (in
fact this was introduced very recently).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes this error on Cell when CONFIG_KEXEC = n:
arch/powerpc/platforms/cell/ras.c:299: error: implicit declaration of function 'crash_shutdown_register'
We have to include <asm/kexec.h> because it contains the dummy
definition of crash_shutdown_register that is used when
CONFIG_KEXEC=n, but <linux/kexec.h> doesn't include <asm/kexec.h> in
that case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
af_unix: netns: fix problem of return value
IRDA: remove double inclusion of module.h
udp: multicast packets need to check namespace
net: add documentation for skb recycling
key: fix setkey(8) policy set breakage
bpa10x: free sk_buff with kfree_skb
xfrm: do not leak ESRCH to user space
net: Really remove all of LOOPBACK_TSO code.
netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()
netns: add register_pernet_gen_subsys/unregister_pernet_gen_subsys
net: delete excess kernel-doc notation
pppoe: Fix socket leak.
gianfar: Don't reset TBI<->SerDes link if it's already up
gianfar: Fix race in TBI/SerDes configuration
at91_ether: request/free GPIO for PHY interrupt
amd8111e: fix dma_free_coherent context
atl1: fix vlan tag regression
SMC91x: delete unused local variable "lp"
myri10ge: fix stop/go mmio ordering
bonding: fix panic when taking bond interface down before removing module
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
Revert "powerpc: Sync RPA note in zImage with kernel's RPA note"
powerpc: Fix compile errors with CONFIG_BUG=n
powerpc: Fix format string warning in arch/powerpc/boot/main.c
powerpc: Fix bug in kernel copy of libfdt's fdt_subnode_offset_namelen()
powerpc: Remove duplicate DMA entry from mpc8313erdb device tree
powerpc/cell/OProfile: Fix on-stack array size in activate spu profiling function
powerpc/mpic: Fix regression caused by change of default IRQ affinity
powerpc: Update remaining dma_mapping_ops to use map/unmap_page
powerpc/pci: Fix unmapping of IO space on 64-bit
powerpc/pci: Properly allocate bus resources for hotplug PHBs
OF-device: Don't overwrite numa_node in device registration
powerpc: Fix swapcontext system for VSX + old ucontext size
powerpc: Fix compiler warning for the relocatable kernel
powerpc: Work around ld bug in older binutils
powerpc/ppc64/kdump: Better flag for running relocatable
powerpc: Use is_kdump_kernel()
powerpc: Kexec exit should not use magic numbers
powerpc/44x: Update 44x defconfigs
powerpc/40x: Update 40x defconfigs
powerpc: enable heap randomization for linkstations
...
This reverts commit 91a0030295, plus
commit 0dcd440120 ("powerpc: Revert CHRP
boot wrapper to real-base = 12MB on 32-bit") which depended on it.
Commit 91a00302 was causing NVRAM corruption on some pSeries machines,
for as-yet unknown reasons, so this reverts it until the cause is
identified.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes sure we don't try to call find_bug or is_warning_bug when
CONFIG_BUG=n and CONFIG_XMON=y. Otherwise we get these errors:
arch/powerpc/xmon/xmon.c: In function ‘print_bug_trap’:
arch/powerpc/xmon/xmon.c:1364: error: implicit declaration of function ‘find_bug’
arch/powerpc/xmon/xmon.c:1364: warning: assignment makes pointer from integer without a cast
arch/powerpc/xmon/xmon.c:1367: error: implicit declaration of function ‘is_warning_bug’
arch/powerpc/xmon/xmon.c:1374: error: dereferencing pointer to incomplete type
make[2]: *** [arch/powerpc/xmon/xmon.o] Error 1
make[1]: *** [arch/powerpc/xmon] Error 2
make: *** [sub-make] Error 2
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix format string warning in arch/powerpc/boot/main.c. Also correct
a typo ("uncomressed") on the same line.
BOOTCC arch/powerpc/boot/main.o
arch/powerpc/boot/main.c: In function 'prep_kernel':
arch/powerpc/boot/main.c:65: warning: format '%08x' expects type
'unsigned int', but argument 3 has type 'long unsigned int'
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's currently an off-by-one bug in fdt_subnode_offset_namelen()
which causes it to keep searching after it's finished the subnodes of
the given parent, and into the subnodes of siblings of the original
node which come after it in the tree. This bug was introduced in
commit ed95d7450d ("powerpc: Update
in-kernel dtc and libfdt to version 1.2.0").
A patch has already been submitted to dtc/libfdt mainline. We don't
really want to pull in a new upstream version during the 2.6.28 cycle,
but we should still fix this bug, hence this standalone version of the
fix for the in-kernel libfdt.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The size of the pm_signal_local array should be equal to the
number of SPUs being configured in the array. Currently, the
array is of size 4 (NR_PHYS_CTRS) but being indexed by a for
loop from 0 to 7 (NUM_SPUS_PER_NODE). This could potentially
cause an oops or random memory corruption since the pm_signal_local
array is on the stack. This fixes it.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Freescale implementation of MPIC only allows a single CPU destination
for non-IPI interrupts. We add a flag to the mpic_init to distinquish
these variants of MPIC. We pull in the irq_choose_cpu from sparc64 to
select a single CPU as the destination of the interrupt.
This is to deal with the fact that the default smp affinity was
changed by commit 1840475676 ("genirq:
Expose default irq affinity mask (take 3)") to be all CPUs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After the merge of the 32 and 64bit DMA code, dma_direct_ops lost
their map/unmap_single() functions but gained map/unmap_page(). This
caused a problem for Cell because Cell's dma_iommu_fixed_ops called
the dma_direct_ops if the fixed linear mapping was to be used or the
iommu ops if the dynamic window was to be used. So in order to fix
this problem we need to update the 64bit DMA code to use
map/unmap_page.
First, we update the generic IOMMU code so that iommu_map_single()
becomes iommu_map_page() and iommu_unmap_single() becomes
iommu_unmap_page(). Then we propagate these changes up through all
the callers of these two functions and in the process update all the
dma_mapping_ops so that they have map/unmap_page rahter than
map/unmap_single. We can do this because on 64bit there is no HIGHMEM
memory so map/unmap_page ends up performing exactly the same function
as map/unmap_single, just taking different arguments.
This has no affect on drivers because the dma_map_single_attrs() just
ends up calling the map_page() function of the appropriate
dma_mapping_ops and similarly the dma_unmap_single_attrs() calls
unmap_page().
This fixes an oops on Cell blades, which oops on boot without this
because they call dma_direct_ops.map_single, which is NULL.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A typo/thinko made us pass the wrong argument to __flush_hash_table_range
when unplugging bridges, thus not flushing all the translations for
the IO space on unplug. The third parameter to __flush_hash_table_range
is `end', not `size'.
This causes the hypervisor to refuse unplugging slots.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Resources for PHB's that are dynamically added to a system are not
properly allocated in the resource tree.
Not having these resources allocated causes an oops when removing
the PHB when we try to release them.
The diff appears a bit messy, this is mainly due to moving everything
one tab to the left in the pcibios_allocate_bus_resources routine.
The functionality change in this routine is only that the
list_for_each_entry() loop is pulled out and moved to the necessary
calling routine.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the numa_node of OF-devices will be overwritten during
device_register, which simply sets the node to -1. On cell machines,
this means that devices can't find their IOMMU, which is referenced
through the device's numa node.
Set the numa node for OF devices with no parent, and use the
lower-level device_initialize and device_add functions, so that the
node is preserved.
We can remove the call to set_dev_node in of_device_alloc, as it
will be overwritten during register.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since VSX support was added, we now have two sizes of ucontext_t;
the older, smaller size without the extra VSX state, and the new
larger size with the extra VSX state. A program using the
sys_swapcontext system call and supplying smaller ucontext_t
structures will currently get an EINVAL error if the task has
used VSX (e.g. because of calling library code that uses VSX) and
the old_ctx argument is non-NULL (i.e. the program is asking for
its current context to be saved). Thus the program will start
getting EINVAL errors on calls that previously worked.
This commit changes this behaviour so that we don't send an EINVAL in
this case. It will now return the smaller context but the VSX MSR bit
will always be cleared to indicate that the ucontext_t doesn't include
the extra VSX state, even if the task has executed VSX instructions.
Both 32 and 64 bit cases are updated.
[paulus@samba.org - also fix some access_ok() and get_user() calls]
Thanks to Ben Herrenschmidt for noticing this problem.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes this warning:
arch/powerpc/kernel/setup_64.c:447:5: warning: "kernstart_addr" is not defined
which arises because PHYSICAL_START is no longer a constant when
CONFIG_RELOCATABLE=y.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 549e8152de ("powerpc: Make the
64-bit kernel as a position-independent executable") added lines to
vmlinux.lds.S to add the extra sections needed to implement a
relocatable kernel. However, those lines seem to trigger a bug in
older versions of GNU ld (such as 2.16.1) when building a
non-relocatable kernel. Since ld 2.16.1 is still a popular choice for
cross-toolchains, this adds an #ifdef to vmlinux.lds.S so the added
lines are only included when building a relocatable kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The __kdump_flag ABI is overly constraining for future development.
As of 2.6.27, the kernel entry point has 4 constraints: Offset 0 is
the starting point for the master (boot) cpu (entered with r3 pointing
to the device tree structure), offset 0x60 is code for the slave cpus
(entered with r3 set to their device tree physical id), offset 0x20 is
used by the iseries hypervisor, and secondary cpus must be well behaved
when the first 256 bytes are copied to address 0.
Placing the __kdump_flag at 0x18 is bad because:
- It was taking the last 8 bytes before the iseries hypervisor data.
- It was 8 bytes for a boolean flag
- It had no way of identifying that the flag was present
- It does leave any room for the master to add any additional code
before branching, which hurts debug.
- It will be unnecessarily hard for 32 bit code to be common (8 bytes)
Now that we have eliminated the use of __kdump_flag in favor of
the standard is_kdump_kernel(), this flag only controls run without
relocating the kernel to PHYSICAL_START (0), so rename it __run_at_load.
Move the flag to 0x5c, 1 word before the secondary cpu entry point at
0x60. Initialize it with "run0" to say it will run at 0 unless it is
set to 1. It only exists if we are relocatable.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
linux/crash_dump.h defines is_kdump_kernel() to be used by code that
needs to know if the previous kernel crashed instead of a (clean) boot
or reboot.
This updates the just added powerpc code to use it. This is needed
for the next commit, which will remove __kdump_flag.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 54622f10a6 ("powerpc: Support for
relocatable kdump kernel") added a magic flag value in a register to
tell purgatory that it should be a panic kernel. This part is wrong
and is reverted by this commit.
The kernel gets a list of memory blocks and a entry point from user space.
Its job is to copy the blocks into place and then branch to the designated
entry point (after turning "off" the mmu).
The user space tool inserts a trampoline, called purgatory, that runs
before the user supplied code. Its job is to establish the entry
environment for the new kernel or other application based on the contents
of memory. The purgatory code is compiled and embedded in the tool,
where it is later patched using the elf symbol table using elf symbols.
Since the tool knows it is creating a purgatory that will run after a
kernel crash, it should just patch purgatory (or the kernel directly)
if something needs to happen.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current defconfig for Linkstation/Kuroboxes has the "Disable Heap
Randomization" option enabled.
Since some of these machines are facing the internet, it helps to have
heap randomization enabled. This patch enables it.
Signed-off-by: Rogério Brito <rbrito@ime.usp.br>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since Linkstations and Kuroboxes often have *very* little memory (as
they are embedded systems), it is desirable to get their kernels
compiled optimized for size.
Signed-off-by: Rogério Brito <rbrito@ime.usp.br>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The i2c bus defn is broken on linkstation / kurobox machines since at
least 2.6.27. Fix it. Also remove CONFIG_SERIAL_OF_PLATFORM, which, if
enabled, breaks the serial console after the
"console handover: boot [udbg0] -> real [ttyS1]" message.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the HCU4 Kconfig option to 'default n'. We don't want the
board to always be enabled for other board defconfigs.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'v28-range-hrtimers-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
hrtimers: add missing docbook comments to struct hrtimer
hrtimers: simplify hrtimer_peek_ahead_timers()
hrtimers: fix docbook comments
DECLARE_PER_CPU needs linux/percpu.h
hrtimers: fix typo
rangetimers: fix the bug reported by Ingo for real
rangetimer: fix BUG_ON reported by Ingo
rangetimer: fix x86 build failure for the !HRTIMERS case
select: fix alpha OSF wrapper
select: fix alpha OSF wrapper
hrtimer: peek at the timer queue just before going idle
hrtimer: make the futex() system call use the per process slack value
hrtimer: make the nanosleep() syscall use the per process slack
hrtimer: fix signed/unsigned bug in slack estimator
hrtimer: show the timer ranges in /proc/timer_list
hrtimer: incorporate feedback from Peter Zijlstra
hrtimer: add a hrtimer_start_range() function
hrtimer: another build fix
hrtimer: fix build bug found by Ingo
hrtimer: make select() and poll() use the hrtimer range feature
...
* 'x86/um-header' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (26 commits)
x86: canonicalize remaining header guards
x86: drop double underscores from header guards
x86: Fix ASM_X86__ header guards
x86, um: get rid of uml-config.h
x86, um: get rid of arch/um/Kconfig.arch
x86, um: get rid of arch/um/os symlink
x86, um: get rid of excessive includes of uml-config.h
x86, um: get rid of header symlinks
x86, um: merge Kconfig.i386 and Kconfig.x86_64
x86, um: get rid of sysdep symlink
x86, um: trim the junk from uml ptrace-*.h
x86, um: take vm-flags.h to sysdep
x86, um: get rid of uml asm/arch
x86, um: get rid of uml highmem.h
x86, um: get rid of uml unistd.h
x86, um: get rid of system.h -> system.h include
x86, um: uml atomic.h is not needed anymore
x86, um: untangle uml ldt.h
x86, um: get rid of more uml asm/arch uses
x86, um: remove dead header (uml module-generic.h; never used these days)
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rric/oprofile: (21 commits)
OProfile: Fix buffer synchronization for IBS
oprofile: hotplug cpu fix
oprofile: fixing whitespaces in arch/x86/oprofile/*
oprofile: fixing whitespaces in arch/x86/oprofile/*
oprofile: fixing whitespaces in drivers/oprofile/*
x86/oprofile: add the logic for enabling additional IBS bits
x86/oprofile: reordering functions in nmi_int.c
x86/oprofile: removing unused function parameter in add_ibs_begin()
oprofile: more whitespace fixes
oprofile: whitespace fixes
OProfile: Rename IBS sysfs dir into "ibs_op"
OProfile: Rework string handling in setup_ibs_files()
OProfile: Rework oprofile_add_ibs_sample() function
oprofile: discover counters for op ppro too
oprofile: Implement Intel architectural perfmon support
oprofile: Don't report Nehalem as core_2
oprofile: drop const in num counters field
Revert "Oprofile Multiplexing Patch"
x86, oprofile: BUG: using smp_processor_id() in preemptible code
x86/oprofile: fix on_each_cpu build error
...
Manually fixed trivial conflicts in
drivers/oprofile/{cpu_buffer.c,event_buffer.h}
The entire file of ftrace.c in the arch code needs to be marked
as notrace. It is much cleaner to do this from the Makefile with
CFLAGS_REMOVE_ftrace.o.
[ powerpc already had this in its Makefile. ]
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The arch dependent function ftrace_mcount_set was only used by the daemon
start up code. This patch removes it.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ftrace daemon is complex and can cause nasty races if something goes
wrong. Since it affects all of the kernel, this patch disables dynamic
ftrace from any arch that depends on the daemon. Until the archs are
ported over to the new MCOUNT_RECORD method, I am disabling dynamic
ftrace from them.
Note: I am leaving in the arch/<arch>/kernel/ftrace.c code alone since
that can be used when the arch is ported to MCOUNT_RECORD. To port
the arch to MCOUNT_RECORD, the scripts/recordmcount.pl needs to be
updated. I will make that easier to do for 2.6.29. For 28, we will keep
the archs disabled.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
the only theoretical reason for it these days is ppc; aside of uml/ppc
being dead, do_signal() would be happier in arch/powerpc/kernel/signal.h
anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This adds relocatable kernel support for kdump. With this one can
use the same regular kernel to capture the kdump. A signature (0xfeed1234)
is passed in r6 from panic code to the next kernel through kexec_sequence
and purgatory code. The signature is used to differentiate between
kdump kernel and non-kdump kernels.
The purgatory code compares the signature and sets the __kdump_flag in
head_64.S. During the boot up, kernel code checks __kdump_flag and if it
is set, the kernel will behave as relocatable kdump kernel. This kernel
will boot at the address where it was loaded by kexec-tools ie. at the
address reserved through crashkernel boot parameter.
CONFIG_CRASH_DUMP depends on CONFIG_RELOCATABLE option to build kdump
kernel as relocatable. So the same kernel can be used as production and
kdump kernel.
This patch incorporates the changes suggested by Paul Mackerras to avoid
GOT use and to avoid two copies of the code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If mem= is used on the boot command line to limit memory then the memory block where a 16G page resides may not be available.
Thanks to Michael Ellerman for finding the problem.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some platforms have variants that can share most of a flat device tree but need
a few devices selectively pruned at boot time. This adds del_node() to ops.h
to allow access to the existing fdt_del_node().
Signed-off-by: Mike Ditto <mditto@consentry.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A patch of mine was recently committed to fix up STRICT_MM_TYPECHECKS
behaviour on powerpc (f5ea64dcba).
However, something which breaks it again seems to have slipped in
afterwards. So, here's another small fix.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove empty/bogus #else from signal_64.c
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Most of the platforms were printing the size of the memory
in their show_cpuinfo implementations. This moves that to
the common show_cpuinfo, so that all 32-bit platforms will
now print the size of memory. I also update the code
to deal with the fact that total_memory is now a phys_addr_t.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The RTC is sitting on the I2C2 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT2 interrupt line, the line is shared with
Vitesse 8201 Ethernet PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MCU is an external Freescale MC9S08QG8 microcontroller, mainly used to
provide soft power-off function, but also exports two GPIOs (wired to
the LEDs and also available from the external headers).
Added the MCU on mpc8349emitx, mpc837xrdb and mpc8315erdb boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change the top-level #address-cells and #size-cells to <2> so the
mpc8572ds.dts is easier to deal with both a true 32-bit physical
or 36-bit physical address space.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't want to encourage the bogus device_type usage.
The device type isn't used in the code, so we can simply remove it from
the documentation and dts files.
Boards should specify proper compatible entries instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These functions should have been static, and inspection shows they
are no longer used. (We used to parse mem= but we now defer that
to early_param).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by addnote to the zImage from
12MB to 32MB. It turns out that this causes unnecessary extra reboots
on old 32-bit CHRP machines. This therefore adds a -r flag to addnote
to allow us to specify what real-base value it should put in the CHRP
note, and adjusts the wrapper script to pass -r c00000 to addnote when
making a zImage for a CHRP machine. Also, CHRP machines ignore the
RPA note, so we don't need to arrange for it to be the same as the
kernel's.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
numa_enforce_memory_limit tried to be smart and only call lmb_end_of_DRAM
when a memory limit was set via mem= on the command line. However,
the early boot code will also limit memory added to the lmb system
when iommu=off is specified. When this happens, the page allocator
is given pages not in the linear mapping and this results in a fatal
data reference to the unmapped page.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We used to assume that even numbered threads were the primary
threads, ie those that would be listed and started as a cpu from
open firmware. Replace a left over is even (% 2) check with a check
for it being a primary thread and update the comments.
Tested with a debug print on pseries, identical code found for cell.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
64 bit powerpc requires the kexec user space tools avoid overwriting
the static kernel image and translation hash table when choosing
where to put memory image data because it copies the data into place
using the kernels virtual memory system. Kexec userspace determines
these and other areas blocked by reading properties the kernel adds,
but does not filter these properties when creating the device tree
for the next kernel.
When the second kernel tries to add its values for these properties,
the export via /proc/device-tree is hidden by the pre-existing but
stale values from the flat tree. Kexec userspace reads the old
property, allocates the new kernel at the old kernel's end, and
gets rejected by the overlap check.
Search and remove these stale properties before adding the new values.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are no users of PPC_MERGE in tree so we can get rid of it.
It was a hold over from the arch/ppc days.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are two issues when we enable CONFIG_RELOCATABLE. The first is due
to the fact that phys_addr_t is now defined in linux/types.h. The second
is due to the fact that the DMA code changes expose memstart_addr to
prom_init.c
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This target is needed to build cuImages with an embedded ramdisk image.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I noticed, when trying to use, e.g.,
node = find_node_by_prop_value(prev, "booleanprop", "", 0))
to search for all nodes with a certain boolean property, that memcmp()
returns garbage when comparing zero bytes. It should return zero.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Adjust amount to reserve based on previous nodes for reserves spanning
multiple nodes. Check if the node active range is empty before attempting
to pass the reserve to bootmem. In practice the range shouldn't be empty,
but to be sure we check.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The issue is the SPU code is not holding the kernel mutex lock while
adding samples to the kernel buffer.
This patch creates per SPU buffers to hold the data. Data
is added to the buffers from in interrupt context. The data
is periodically pushed to the kernel buffer via a new Oprofile
function oprofile_put_buff(). The oprofile_put_buff() function
is called via a work queue enabling the funtion to acquire the
mutex lock.
The existing user controls for adjusting the per CPU buffer
size is used to control the size of the per SPU buffers.
Similarly, overflows of the SPU buffers are reported by
incrementing the per CPU buffer stats. This eliminates the
need to have architecture specific controls for the per SPU
buffers which is not acceptable to the OProfile user tool
maintainer.
The export of the oprofile add_event_entry() is removed as it
is no longer needed given this patch.
Note, this patch has not addressed the issue of indexing arrays
by the spu number. This still needs to be fixed as the spu
numbering is not guarenteed to be 0 to max_num_spus-1.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <maynardj@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Acked-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
"unsigned int" speed cannot be negative, it's thus pointless
to test if it is.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pfn of the memory to be removed should be validated prior to
attempting to remove the memory. In cases where the probe of a
memory section fails during hotplug add, the pfn for the lmb may
not be valid.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the vmlinux binary in memory is larger than 4 MiB than it collides
with the initial boot code which is linked at 4 MiB in case of cuBoot.
If the the uncompressed image size (on disk size) is less than 4 MiB
then it would fit. The difference between those two sizes is the bss
section. In cuBoot we have the dtb embedded right after the data
section so it is very likely that the reset of the bss section (in
kernel's start up code) will overwrite the dtb blob. Therefore we
reallocate the dtb. Something similar is allready done to the initrd.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds a comment to clarify why atomic_dec_if_positive is being used
to decrement gang's aff_sched_count on SPU context unbind.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This patch improves redability of the code responsible for trying to find
a node with enough SPUs not committed to other affinity gangs.
An additional check is also added, to avoid taking into account gangs that
have no SPU affinity.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
With most file readers (eg cat, dd), reading a context's regs file will
result in two reads: the first to read the data, and the second to
return EOF. Because each read performs a spu_acquire_saved, we end up
descheduling and re-scheduling the context twice.
This change does a simple check to see if we'd return EOF before
calling spu_acquire_saved(), saving the extra schedule operation.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, read() on the sputrace log will block until the read buffer
is full. This makes it difficult to retrieve the end of the buffer, as
the user will need to read with the right-sized buffer.
In a similar method as 91553a1b5e0df006a3573a88d98ee7cd48a3818a, this
change makes the switch_log return if there has already been data
read.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we use ctx->mapping_lock and ctx->switch_log->lock for the
context switch log. The mapping lock only prevents concurrent open()s,
so we require the switch_lock->lock for reads.
Since writes to the switch log buffer occur on context switches, we're
better off synchronising with the state_mutex, which is held during a
switch. Since we're serialised througout the buffer reads and writes,
we can use the state mutex to protect open and release too, and
can now kfree() the log buffer on release. This allows us to perform
the switch log notify without taking any extra locks.
Because the buffer is only present while the file is open, we can use
it to prevent multiple simultaneous openers.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, read() on the sputrace buffer will only return data when
the user buffer is exhausted. This may mean that we never see the
end of the event log, unless we read() with exactly the right-sized
buffer.
This change makes sputrace_read not block if we have data ready to
return.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, sputrace will start logging to the event buffer before the
log buffer has been open()ed. This results in a heap of "lost samples"
warnings if the sputrace file hasn't yet been opened.
Since the buffer is reset on open() anyway, there's no need to enable
logging when no-one has opened the log.
Because open clears the log, make it return EBUSY for mutliple open
calls.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (41 commits)
PCI: fix pci_ioremap_bar() on s390
PCI: fix AER capability check
PCI: use pci_find_ext_capability everywhere
PCI: remove #ifdef DEBUG around dev_dbg call
PCI hotplug: fix get_##name return value problem
PCI: document the pcie_aspm kernel parameter
PCI: introduce an pci_ioremap(pdev, barnr) function
powerpc/PCI: Add legacy PCI access via sysfs
PCI: Add ability to mmap legacy_io on some platforms
PCI: probing debug message uniformization
PCI: support PCIe ARI capability
PCI: centralize the capabilities code in probe.c
PCI: centralize the capabilities code in pci-sysfs.c
PCI: fix 64-vbit prefetchable memory resource BARs
PCI: replace cfg space size (256/4096) by macros.
PCI: use resource_size() everywhere.
PCI: use same arg names in PCI_VDEVICE comment
PCI hotplug: rpaphp: make debug var unique
PCI: use %pF instead of print_fn_descriptor_symbol() in quirks.c
PCI: fix hotplug get_##name return value problem
...
This patch adds support for legacy_io and legacy_mem files in
bus class directories in sysfs for powerpc
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Due to confusion between the ftrace infrastructure and the gcc profiling
tracer "ftrace", this patch renames the config options from FTRACE to
FUNCTION_TRACER. The other two names that are offspring from FTRACE
DYNAMIC_FTRACE and FTRACE_MCOUNT_RECORD will stay the same.
This patch was generated mostly by script, and partially by hand.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: OMAP: Fix DSP DAI format in McBSP DAI driver
go7007 - Add missing dependency on sound subsystem
ALSA: ps3: Add support for SPDIF/HDMI passthru
ps3: Add passthru support for non-audio streams
ps3: Add ps3av_audio_mute_analog()
ALSA: misc typo fixes
sound: add missing pcm kernel-doc
o elfcorehdr_addr is used by not only the code under CONFIG_PROC_VMCORE
but also by the code which is not inside CONFIG_PROC_VMCORE. For
example, is_kdump_kernel() is used by powerpc code to determine if
kernel is booting after a panic then use previous kernel's TCE table.
So even if CONFIG_PROC_VMCORE is not set in second kernel, one should be
able to correctly determine that we are booting after a panic and setup
calgary iommu accordingly.
o So remove the assumption that elfcorehdr_addr is under
CONFIG_PROC_VMCORE.
o Move definition of elfcorehdr_addr to arch dependent crash files.
(Unfortunately crash dump does not have an arch independent file
otherwise that would have been the best place).
o kexec.c is not the right place as one can Have CRASH_DUMP enabled in
second kernel without KEXEC being enabled.
o I don't see sh setup code parsing the command line for
elfcorehdr_addr. I am wondering how does vmcore interface work on sh.
Anyway, I am atleast defining elfcoredhr_addr so that compilation is not
broken on sh.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements a new freezer subsystem in the control groups
framework. It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.
The freezer subsystem in the container filesystem defines a file named
freezer.state. Writing "FROZEN" to the state file will freeze all tasks
in the cgroup. Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup. Reading will return the current state.
* Examples of usage :
# mkdir /containers/freezer
# mount -t cgroup -ofreezer freezer /containers
# mkdir /containers/0
# echo $some_pid > /containers/0/tasks
to get status of the freezer subsystem :
# cat /containers/0/freezer.state
RUNNING
to freeze all tasks in the container :
# echo FROZEN > /containers/0/freezer.state
# cat /containers/0/freezer.state
FREEZING
# cat /containers/0/freezer.state
FROZEN
to unfreeze all tasks in the container :
# echo RUNNING > /containers/0/freezer.state
# cat /containers/0/freezer.state
RUNNING
This is the basic mechanism which should do the right thing for user space
task in a simple scenario.
It's important to note that freezing can be incomplete. In that case we
return EBUSY. This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time. After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read. The state will remain
"FREEZING" until one of these things happens:
1) Userspace cancels the freezing operation by writing "RUNNING" to
the freezer.state file
2) Userspace retries the freezing operation by writing "FROZEN" to
the freezer.state file (writing "FREEZING" is not legal
and returns EIO)
3) The tasks that blocked the cgroup from entering the "FROZEN"
state disappear from the cgroup's set of tasks.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Tested-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is nothing architecture specific about remove_memory().
remove_memory() function is common for all architectures which support
hotplug memory remove. Instead of duplicating it in every architecture,
collapse them into arch neutral function.
[akpm@linux-foundation.org: fix the export]
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the channel status bit setting so that non-PCM
data stream can be sent (i.e. pass-through) via SPDIF/HDMI.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for muting the analog output so that it does not
play noises while non-PCM data is played.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the GPIO functions of PPC40x and PPC44x
SOCs.
Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Adds support for a HCU4 PPC405GPr based board from Netstal Maschinen AG.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a cuboot wrapper for the AMCC PowerPC 405EZ Acadia board. The
clocking code is derived from U-Boot, originally written by Stefan Roese.
Signed-off-by: Josh Boyer <jwboyer@linux.ibm.com>
This adds a common board file for almost all of the "simple" PowerPC 40x
boards that exist today. This is intended to be a single place to add
support for boards that do not differ in platform support from most of the
evaluation boards that are used as reference platforms. Boards that have
specific requirements or custom hardware setup should still have their own
board.c file.
The first board ported to this is the AMCC PowerPC 405EZ Acadia board.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the base DTS for the AMCC PowerPC 405EZ Acadia evalution board.
In addition to some of the normal PPC 40x peripherals, the Acadia
board has:
- 64 MiB PSRAM
- NOR and NAND flash
- Two USB 1.1 host ports
- Two CAN 2.0 ports
- ADC and DAC connectors
- LCD display
This adds the basic platform support to build from.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (134 commits)
KVM: ia64: Add intel iommu support for guests.
KVM: ia64: add directed mmio range support for kvm guests
KVM: ia64: Make pmt table be able to hold physical mmio entries.
KVM: Move irqchip_in_kernel() from ioapic.h to irq.h
KVM: Separate irq ack notification out of arch/x86/kvm/irq.c
KVM: Change is_mmio_pfn to kvm_is_mmio_pfn, and make it common for all archs
KVM: Move device assignment logic to common code
KVM: Device Assignment: Move vtd.c from arch/x86/kvm/ to virt/kvm/
KVM: VMX: enable invlpg exiting if EPT is disabled
KVM: x86: Silence various LAPIC-related host kernel messages
KVM: Device Assignment: Map mmio pages into VT-d page table
KVM: PIC: enhance IPI avoidance
KVM: MMU: add "oos_shadow" parameter to disable oos
KVM: MMU: speed up mmu_unsync_walk
KVM: MMU: out of sync shadow core
KVM: MMU: mmu_convert_notrap helper
KVM: MMU: awareness of new kvm_mmu_zap_page behaviour
KVM: MMU: mmu_parent_walk
KVM: x86: trap invlpg
KVM: MMU: sync roots on mmu reload
...
This is a preparation patch for introducing a generic iommu_num_pages function.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nothing arch specific in get/settimeofday. The details of the timeval
conversion varied a little from arch to arch, but all with the same
results.
Also add an extern declaration for sys_tz to linux/time.h because externs
in .c files are fowned upon. I'll kill the externs in various other files
in a sparate patch.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net> [ sparc bits ]
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct stat / compat_stat is the same on all architectures, so
cp_compat_stat should be, too.
Turns out it is, except that various architectures have slightly and some
high2lowuid/high2lowgid or the direct assignment instead of the
SET_UID/SET_GID that expands to the correct one anyway.
This patch replaces the arch-specific cp_compat_stat implementations with
a common one based on the x86-64 one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net> [ sparc bits ]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [ parisc bits ]
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SET_PERSONALITY macro is always called with a second argument of 0.
Remove the ibcs argument and the various tests to set the PER_SVR4
personality.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Today's linux-next build (powerpc allyesconfig) failed like this:
In file included from arch/powerpc/include/asm/mmu-hash64.h:17,
from arch/powerpc/include/asm/mmu.h:8,
from arch/powerpc/include/asm/pgtable.h:8,
from arch/powerpc/mm/slb.c:20:
arch/powerpc/include/asm/page.h:76: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'memstart_addr'
arch/powerpc/include/asm/page.h:77: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'kernstart_addr'
Caused by commit 600715dcdf ("generic: add
phys_addr_t for holding physical addresses") from the tip-core tree.
This only fails if CONFIG_RELOCATABLE is set.
So include that instead of asm/types.h in asm/page.h for
the CONFIG_RELOCATABLE case.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: ppc-dev <linuxppc-dev@ozlabs.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
MPC5200 needs to have pipelining disabled for ATA to work. MPC5200B does not.
So, for the latter, don't touch the original setting from the bootloader.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Current device trees do not have the device_type = soc property set
anymore. Fix up the cuImage bootwrapper fragment to still find the IMMR
nodes.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert gfn_to_pfn to use get_user_pages_fast, which can do lockless
pagetable lookups on x86. Kernel compilation on 4-way guest is 3.7%
faster on VMX.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When we use TID=N userspace mappings, we must ensure that kernel mappings have
been destroyed when entering userspace. Using TID=1/TID=0 for kernel/user
mappings and running userspace with PID=0 means that userspace can't access the
kernel mappings, but the kernel can directly access userspace.
The net is that we don't need to flush the TLB on privilege switches, but we do
on guest context switches (which are far more infrequent). Guest boot time
performance improvement: about 30%.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Track which TLB entries need to be written, instead of overwriting everything
below the high water mark. Typically only a single guest TLB entry will be
modified in a single exit.
Guest boot time performance improvement: about 15%.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We're saving the host TLB state to memory on every exit, but never using it.
Originally I had thought that we'd want to restore host TLB for heavyweight
exits, but that could actually hurt when context switching to an unrelated host
process (i.e. not qemu).
Since this decreases the performance penalty of all exits, this patch improves
guest boot time by about 15%.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Allow host userspace to program hardware debug registers to set breakpoints
inside guests.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds a trace point for the instruction emulation on embedded powerpc
utilizing the KVM_TRACE interface.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds trace points to track powerpc TLB activities using the
KVM_TRACE infrastructure.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch enables KVM_TRACE to build for PowerPC arch. This means just
adding sections to Kconfig and Makefile.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Recently, indirect_pci was changed to test if the bus number requested
is the one hanging straight off the PHB, then it substitutes the bus
number with another one contained in a new "self_busno" field of the
pci_controller structure.
However, this breaks CHRP which didn't initialize this new field, and
which relies on having the right bus number passed to the hardware.
This fixes it by initializing this variable properly for all CHRP bridges
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The detection of the IBM "Python" PCI host bridge on IBM CHRP
machines such as old RS6000 was broken when we changed
of_device_is_compatible() from strncasecmp to strcasecmp (dropped
the "n" variant) due to the way IBM encodes the chip version.
We fix that by instead doing a match on the model property like
we do for others bridges in that file. It should be good enough
for those machines. If yours is still broken, let me know.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
prom_init was changed to take a new argument, the address
where the kernel is loaded, which is now used to copy the
SMP spin loop down before use.
However, only head_64.S was adapted to pass this new value,
not head_32.S, thus breaking SMP boot on 32-bit SMP CHRP
machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new merged DMA code will try to access isa_bridge_pcidev when
trying to DMA to/from legacy devices. This is however only defined
on 64-bit. Fixes this for now by adding the variable, even if it
stays NULL. In the long run, we'll make isa-bridge.c common to
32 and 64-bit.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the powerpc PCI layer is not configured to re-assign everything,
it currently fails to detect that a PCI to PCI bridge has been left
unassigned by the firmware and tries to allocate resource for the
default window values in the bridge (0...X) (with the notable exception
of a hack we have in there that detects some Apple firmware unassigned
bridge resources).
This results in resource allocation failures, which are generally
fixed up later on but it causes scary warnings in the logs and we
have seen the fixup code fall over in some circumstances (a different
issue to fix as well).
This code improves that by providing a more complete & useful function
to intuit that a bridge was left unassigned by the firmware, and thus
force a full re-allocation by the PCI code without trying to allocate
the existing useless resources first.
The algorithm we use basically considers unassigned a window that
starts at 0 (PCI address) if the corresponding address space enable
bit is not set. In addition, for memory space, it considers such a
resource unassigned also if the host bridge isn't configured to
forward cycles to address 0 (ie, the resource basically overlaps
main memory).
This fixes a range of problems with things like Bare-Metal support
on pSeries machines, or attempt to use partial firmware PCI setup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need a marker_synchronize_unregister() before the end of exit() to make sure
every probe callers have exited the non preemptible section and thus are not
executing the probe code anymore.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The typesafe version of the powerpc pagetable handling (with
USE_STRICT_MM_TYPECHECKS defined) has bitrotted again. This patch
makes a bunch of small fixes to get it back to building status.
It's still not enabled by default as gcc still generates worse
code with it for some reason.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The "phys" argument to machine_init() isn't used and isn't likely to
ever be so let's remove it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After Becky's work we can almost have different DMA offsets
between on-chip devices and PCI. Almost because there's a
problem with the non-coherent DMA code that basically ignores
the programmed offset to use the global one for everything.
This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a much better version of a previous patch to make the parser
tables constant. Rather than changing the typedef, we put the "const" in
all the various places where its required, allowing the __initconst
exception for nfsroot which was the cause of the previous trouble.
This was posted for review some time ago and I believe its been in -mm
since then.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Alexander Viro <aviro@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The fsl_upm nand driver fails to build because fsl_lbc_lock isn't
exported, the lock is needed by the inlined fsl_upm_run_pattern()
function:
ERROR: "fsl_lbc_lock" [drivers/mtd/nand/fsl_upm.ko] undefined!
Dave Jones purposed to export the lock, but it is better to just uninline
the fsl_upm_run_pattern().
When uninlined we also no longer need the exported fsl_lbc_regs, and
both fsl_lbc_lock and fsl_lbc_regs could be marked static.
While at it, also add some missing includes that we should have included
explicitly.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The StMicro NAND chip (512Mbit, 64MB) is connected to the local bus,
the first local bus' user-programmable machine is configured by the
firmware to work with NAND chips.
QE GPIO pin is used to poll the NAND's Ready-Not-Busy signal.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This patch adds support for the registers held in the devices main FPGA,
exposing extra information about the revision of the board through cpuinfo.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale Elo DMA driver binds to all DMA channels in the device tree that
are compatible with "fsl,eloplus-dma-channel". This conflicts with the sound
drivers for the MPC8610 HPCD. On this board, the SSI uses two DMA channels and
therefore those channels are not available for general purpose use. We
change the compatible properties for these channels "fsl,ssi-dma-channel".
This works because the sound drivers don't actually check the compatible
property when it grabs channels.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Because CHRP and PMAC are by default enabled, several non-CHRP and non-PMAC
PowerPC defconfigs will have these Kconfig options set erroneously.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The RTC is sitting on the I2C1 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT3 interrupt line.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Early versions of the Freescale DIU framebuffer driver depended on a bootmem
allocation of memory for the video buffer. The need for this feature was
removed in commit 6b51d51a, so now we can remove the platform-specific code
that allocated that memory.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
b38fd42ff4 added false dependencys
to order the load of upper and lower halfs of the pte, but only
adjusted whitespace instead of deleting the old load in the iside
handler, letting the hardware see the non-dependent load.
This patch removes the extra load.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Uses mpc83xx_add_bridge in fsl_pci.c
Adds second register tuple to pci node register property
as done for 83xx device trees in a previous patch.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.
83xx pci nodes have this change:
register properties now contain two address length tuples:
First is the pci bridge register base, this has always been there.
Second is the config base, this is new.
This is documented in dts-bindings/fsl/83xx-512x-pci.txt
The changes accomplish these things:
mpc83xx_add_bridge no longer needs to call get_immrbase
it uses hard coded addresses if the second register value is missing
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The class of the MPC5121 pci host bridge is PCI_CLASS_BRIDGE_OTHER
while other freescale host bridges have class set to
PCI_CLASS_PROCESSOR_POWERPC.
This patch makes fixup_hide_host_resource_fsl match
PCI_CLASS_BRIDGE_OTHER in addition to PCI_CLASS_PROCESSOR_POWERPC.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the standalone setup the board's CPLD disables the PCI internal
arbiter, thus any access to the PCI bus will hang the board.
The common way to disable particular devices in the device tree is to
put the "status" property with any value other than "ok" or "okay"
into the device node we want to disable.
So, when there is no PCI arbiter on the bus the u-boot adds status =
"broken (no arbiter)" property into the PCI controller's node, and so
marks the PCI controller as unavailable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Specifying user-selectable option in the qe_lib/Kconfig was a bad idea
because the qe_lib/Kconfig is included into the top level Kconfig, and
thus the QE_GPIO option appears at the top level menu.
This patch effectively moves the QE_GPIO option under the platform menu
instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify the Kconfig so that Freescale QUICC Engine (QE) support is a selectable
option, thereby allowing users to compile kernels without any QE support.
The drawback is that QE support is now disabled by default on platforms that
have a QE, and so a defconfig is needed to enable QE and QE devices (like
UCC GETH). Fortunately, all the current relevant defconfigs do that already.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE Fanuc (PowerPC MPC8641D).
A number of MPC8641D based route interrupts for on-board interrupts through
a FPGA based interrupt controller, which is chained with the
MPC8641D's mpic. This patch provides a basic driver to allow basic routing
of interrupts to the mpic.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The comment in the code was asking "Do we have to do this?", and according
to x86 and s390 the answer is no, the scheduler will do it before calling
the arch hook.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A single full sync (mb()) is requrired to order the mmio to the qirr reg
with the set or clear of the message word. However, test_and_clear_bit
has the effect of smp_mb() and we are not doing any other io from here,
so we don't need a mb per bit processed.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Several printks were broken at word boundaries for line length. Some
even referred to old function names. Using __func__ and changing the
text slightly for the format allows these printk formats to fit on one
line.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It is physically per-cpu, and we want the irq layer to treat it that way.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
EOI normally has the side effect of returning the cpu to the base
priority to recieve the next interrupt. This is actually controlled
by the top byte of the xirr register. When we are exiting the
kernel in kexec we must eoi the ipi for the next kernel because we
never return from the handler, but we want to leave interrupt
delivery blocked until the next kernel takes action.
Since the hardware ipi vector is fixed, its easiest to just do the
eoi explicitly.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This factors out processors joining and unjoining the Global Interrupt
Queue into a separate function.
There is a bit of math to calculate the arguments to rtas to join
or leave the global interrupt queue, and a warning on failure
afterwards. Make a helper for the 3 callers.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We only need to check the ibm,interrupt-server#-size property once, not
once per global server and thread.
We can use !CONFIG_SMP cpu masks and hard_smp_processor_id() to avoid an ifdef.
Put the node when breaking out of the loop on lpar systems.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Trim unneeded includes from xics.c. We don't use signals or gfp
flags, we use only OF functions and don't need prom, and the 8259
is now handled by our caller.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The xirr is 32 bits in hardware, but the hypervisor requries the upper
bits of the register to be clear on the hcall. By changing the type
from signed to unsigned int we can drop masking it back to 32 bits.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that xics_update_irq_servers is called only from init and hotplug
code, it becomes possible to clean up the ordering of functions in the
file, grouping them but the interfaces they implement.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
xics supports only one ipi per cpu, and expects software to use some
queue to know why the interrupt was sent. In Linux, we use a an array
of bitmaps indexed by cpu to identify the message. Currently the bits
are set in smp.c and decoded in xics.c, with the data structure in a
header file. Consolidate the code in xics.c similar to mpic and other
interrupt controllers.
Also, while making the the array static, the message word doesn't need
to be volatile as set_bit and test_clear_bit take care of it for us, and
put it under ifdef smp.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previously the FDT header field boot_cpuid_phys wasn't actually used
on ppc32. Instead the physical boot cpuid was assumed to be 0 for
!CONFIG_SMP.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is an old workaround in the sysdev/Makefile for dealing
with arch/ppc vs. arch/powerpc compiles. This is no longer
needed as arch/ppc is dead.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, every time we determine which irq server to use, we check if
default_server, which is the id of the bootcpu, is still online. But
default_server is a hardware cpu, not the logical cpu id needed to index
cpu_online_map.
Since the default server can only go offline during a cpu hotplug event,
explicitly check the default server and choose the new one when we move
irqs away from the cpu being offlined.
This has the added benefit of only needing the boot_cpuid to be updated
and not relying on the cpu being marked offline during migrate_irqs_away.
Also, since xics_update_irq_servers only reads device tree information, we
can call it before xics_init_host in xics_init_IRQ and then default_server
will always be valid when we can reach get_irq_server via the host ops.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When reciving an irq vector that does not have a linux mapping, the kernel
prints a message and calls RTAS to disable the irq source. Previously
the kernel did not EOI the interrupt, causing the source to think it is
still being processed by software. While this does add an additional
layer of protection against interrupt storms had RTAS failed to disable
the source, it also prevents the interrupt from working when a driver
later enables it. (We could alternatively send an EOI on startup, but
that strategy would likely fail on an emulated xics.)
All interrupts should be disabled when the kernel starts, but this can
be observed if a driver does not shutdown an interrupt in its reboot
hook before starting a new kernel with kexec.
Michael reports this can be reproduced trivially by banging the keyboard
while kexec'ing on a P5 LPAR: even though the hvc_console driver request's
the console irq later in boot, the console is non-functional because
we're receiving no console interrupts.
Reported-By: Michael Ellerman
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1075 commits)
myri10ge: update driver version number to 1.4.3-1.369
r8169: add shutdown handler
r8169: preliminary 8168d support
r8169: support additional 8168cp chipset
r8169: change default behavior for mildly identified 8168c chipsets
r8169: add a new 8168cp flavor
r8169: add a new 8168c flavor (bis)
r8169: add a new 8168c flavor
r8169: sync existing 8168 device hardware start sequences with vendor driver
r8169: 8168b Tx performance tweak
r8169: make room for more specific 8168 hardware start procedure
r8169: shuffle some registers handling around (8168 operation only)
r8169: new phy init parameters for the 8168b
r8169: update phy init parameters
r8169: wake up the PHY of the 8168
af_key: fix SADB_X_SPDDELETE response
ath9k: Fix return code when ath9k_hw_setpower() fails on reset
ath9k: remove nasty FAIL macro from ath9k_hw_reset()
gre: minor cleanups in netlink interface
gre: fix copy and paste error
...
If there are multiple reserved memory blocks via lmb_reserve() that are
contiguous addresses and on different NUMA nodes we are losing track of which
address ranges to reserve in bootmem on which node. I discovered this
when I recently got to try 16GB huge pages on a system with more then 2 nodes.
When scanning the device tree in early boot we call lmb_reserve() with
the addresses of the 16G pages that we find so that the memory doesn't
get used for something else. For example the addresses for the pages
could be 4000000000, 4400000000, 4800000000, 4C00000000, etc - 8 pages,
one on each of eight nodes. In the lmb after all the pages have been
reserved it will look something like the following:
lmb_dump_all:
memory.cnt = 0x2
memory.size = 0x3e80000000
memory.region[0x0].base = 0x0
.size = 0x1e80000000
memory.region[0x1].base = 0x4000000000
.size = 0x2000000000
reserved.cnt = 0x5
reserved.size = 0x3e80000000
reserved.region[0x0].base = 0x0
.size = 0x7b5000
reserved.region[0x1].base = 0x2a00000
.size = 0x78c000
reserved.region[0x2].base = 0x328c000
.size = 0x43000
reserved.region[0x3].base = 0xf4e8000
.size = 0xb18000
reserved.region[0x4].base = 0x4000000000
.size = 0x2000000000
The reserved.region[0x4] contains the 16G pages. In
arch/powerpc/mm/num.c: do_init_bootmem() we loop through each of the
node numbers looking for the reserved regions that belong to the
particular node. It is not able to identify region 0x4 as being a part
of each of the 8 nodes. It is assuming that a reserved region is only
on a single node.
This patch takes out the reserved region loop from inside
the loop that goes over each node. It looks up the active region containing
the start of the reserved region. If it extends past that active region then
it adjusts the size and gets the next active region containing it.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by the addnote program from
12MB to 32MB to give more space for Open Firmware to load the zImage.
(The real-base value says where we want OF to position itself in
memory.) However, this change was ineffective on most pSeries
machines, because the RPA note added by addnote has the "ignore me"
flag set to 1. This was intended to tell OF to ignore just the RPA
note, but has the side effect of also making OF ignore the CHRP note
(at least on most pSeries machines).
To solve this we have to set the "ignore me" flag to 0 in the RPA
note. (We can't just omit the RPA note because that is equivalent to
having an RPA note with default values, and the default values are not
what we want.) However, then we have to make sure the values in the
zImage's RPA note match up with the values that the kernel supplies
later in prom_init.c with either the ibm,client-architecture-support
call or the process-elf-header call in prom_send_capabilities().
So this sets the "ignore me" flag in the RPA note in addnote to 0, and
adjusts the RPA note values in addnote.c and in prom_init.c to be
consistent with each other and with the values in ibm_architecture_vec.
However, since the wrapper is independent of the kernel, this doesn't
ensure that the notes will stay consistent. To ensure that, this adds
code to addnote.c so that it can extract the kernel's RPA note from
the kernel binary and put that in the zImage. To that end, we put the
kernel's fake ELF header (which contains the kernel's RPA note) into
its own section, and arrange for wrapper to pull out that section with
objcopy and pass it to addnote, which then extracts the RPA note from
it and transfers it to the zImage.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc 32-bit and 64-bit kernel_thread functions don't properly
propagate errors being returned by the clone syscall. (In the case of
error, the syscall exit code returns a positive errno in r3 and sets
the CR0[SO] bit.)
This patch fixes that by negating r3 if CR0[SO] is set after the syscall.
Signed-off-by: Josh Poimboeuf <jpoimboe@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Offset is unsigned and when an address isn't found in the vma map
vma_map_lookup() returns the vma physical address + 0x10000000.
vma_map_lookup used to return 0xffffffff on a failed lookup, but
a change was made to return the vma physical address + 0x10000000
There are two callers of vam_map_lookup: one of them correctly
deals with this new return value, but the other (below) did not.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Maynard Johnson <maynardj@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Rostedt
Steven Rostedt
Ingo Molnar
Hollis Blanchard
Paul Mackerras
Jeremy Kerr
Michael Barkowski
Martyn Welch
Trent Piepho
Milton Miller
Robert Jennings
Michael Ellerman
Nick Piggin
Mark Nelson
Geert Uytterhoeven
Grant Likely
James Morris
David Howells
Benjamin Herrenschmidt
Grant Erickson
Andreas Schwab
Kumar Gala
Li Yang
Harvey Harrison
Sebastian Siewior
Jon Tollefson
Masakazu Mokuno
Brian King
Sebastien Dugue
Anton Vorontsov
Stephen Rothwell
Alexey Dobriyan
Linus Torvalds
Jon Smirl
David Gibson
Mike Dyer
David S. Miller
Carl Love
Nathan Fontenot
Michael Neuling
Josh Boyer
Rogério Brito
Guennadi Liakhovetski
Steven Rostedt
Al Viro
Thomas Gleixner
Mohan Kumar M
Jon Tollefson
Mike Ditto
Becky Bruce
Ed Swarthout
Jason Jin
roel kluin
Andre Detsch
Vivek Goyal
Matt Helsley
Badari Pulavarty
Takashi Iwai
Steven A. Falco
Niklaus Giger
Arjan van de Ven
Joerg Roedel
Christoph Hellwig
Martin Schwidefsky
Robert Richter
Wolfram Sang
Marcelo Tosatti
Christian Ehrhardt
Jerone Young
Mathieu Desnoyers
Steven Whitehouse
David Woodhouse
Timur Tabi
John Rigby
Josh Poimboeuf
Roel Kluin