The Octal DTR configuration is stored in the CFR5V register. This
register is 1 byte wide. But 1 byte long transactions are not allowed in
8D-8D-8D mode. Since the next byte address does not contain any
register, it is safe to write any value to it. Write a 0 to it.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20210531181757.19458-3-p.yadav@ti.com
The template ops used in spi_nor_spimem_check_pp() and
spi_nor_spimem_check_readop() currently set the data phase to 1 byte
long. This is problematic for 8D-8D-8D protocol where odd length data
phase is invalid since one cycle transfers 2 bytes and odd number of
bytes would mean half a cycle is left over. This could result in a
controller rejecting the op as "not supported" even though it actually
supports the protocol.
Change the data length to 2 bytes in these templates. One might argue
that this should only be done for 8D-8D-8D operations but when talking
about these templates, there is no functional difference between one and
two bytes, even in STR modes.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210531181757.19458-2-p.yadav@ti.com
Remove the references to the old spi-nor.c file.
The old drivers/mtd/spi-nor/spi-nor.c file
is not more present and now some of its code is contained in:
drivers/mtd/spi-nor/core.c
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
[tudor.ambarus@microchip.com:
- remove change in Documentation/driver-api/mtd/spi-nor.rst.
The documentation has to be rewritten entirely.
- update commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20210126092516.1431913-1-f.suligoi@asem.it
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211221212609.31290-3-prabhakar.mahadev-lad.rj@bp.renesas.com
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211221212609.31290-2-prabhakar.mahadev-lad.rj@bp.renesas.com
The GPMC device driver is required for NAND controller
to work on K3 Architecture. Select it if required.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211221131757.2030-5-rogerq@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As more compatibles can be added to the GPMC NAND controller driver
use a compatible match table.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211221131757.2030-4-rogerq@kernel.org
[krzysztof: remove "is_nand" variable]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Introduce Renesas NAND controller driver which currently supports the
following features on R-Car Gen3 and RZ/N1 SoCs:
- All ONFI timing modes
- Different configurations of its internal ECC controller
- On-die (not tested) and software ECC support
- Several chips (not tested)
- Subpage accesses
- DMA and PIO
This controller was originally provided by Evatronix before being bought
by Cadence.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/linux-mtd/20211217142033.353599-3-miquel.raynal@bootlin.com
This is an assortment of driver patches that rely on some of the changes
in the for-5.17/soc branch. These have all been acked by the respective
maintainers and go through the Tegra tree to more easily handle the
build dependency.
-----BEGIN PGP SIGNATURE-----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=YfSG
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=lWBt
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.17-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
drivers: Changes for v5.17-rc1
This is an assortment of driver patches that rely on some of the changes
in the for-5.17/soc branch. These have all been acked by the respective
maintainers and go through the Tegra tree to more easily handle the
build dependency.
* tag 'tegra-for-5.17-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
media: staging: tegra-vde: Support generic power domain
spi: tegra20-slink: Add OPP support
mtd: rawnand: tegra: Add runtime PM and OPP support
mmc: sdhci-tegra: Add runtime PM and OPP support
pwm: tegra: Add runtime PM and OPP support
bus: tegra-gmi: Add runtime PM and OPP support
usb: chipidea: tegra: Add runtime PM and OPP support
soc/tegra: Add devm_tegra_core_dev_init_opp_table_common()
soc/tegra: Enable runtime PM during OPP state-syncing
Link: https://lore.kernel.org/r/20211217162253.1801077-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In DMA mode we were not considering the force_8bit flag.
Fix it by using regular non-DMA 8-bit I/O if force_8bit flag is set.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211209090458.24830-6-rogerq@kernel.org
The slave_id was previously used to pick one DMA slave instead of another,
but this is now done through the DMA descriptors in device tree.
For the qcom_adm driver, the configuration is documented in the DT
binding to contain a tuple of device identifier and a "crci" field,
but the implementation ends up using only a single cell for identifying
the slave, with the crci getting passed in nonstandard properties of
the device, and passed through the dma driver using the old slave_id
field. Part of the problem apparently is that the nand driver ends up
using only a single DMA request ID, but requires distinct values for
"crci" depending on the type of transfer.
Change both the dmaengine driver and the two slave drivers to allow
the documented binding to work in addition to the ad-hoc passing
of crci values. In order to no longer abuse the slave_id field, pass
the data using the "peripheral_config" mechanism instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-9-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The NAND on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now NAND must be resumed using
runtime PM API in order to initialize the NAND power state. Add runtime PM
and OPP support to the NAND driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In the mtdchar_write_ioctl() function, memdup_user() is called with its
'len' parameter set to verbatim values provided by user space via a
struct mtd_write_req. Both the 'len' and 'ooblen' fields of that
structure are 64-bit unsigned integers, which means the MEMWRITE ioctl
can trigger unbounded kernel memory allocation requests.
Fix by iterating over the buffers provided by user space in a loop,
processing at most mtd->erasesize bytes in each iteration. Adopt some
checks from mtd_check_oob_ops() to retain backward user space
compatibility.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211130113149.21848-1-kernel@kempniu.pl
'chip_map' is a bitmap. So use 'bitmap_zalloc()' to simplify code,
improve the semantic and avoid some open-coded arithmetic in allocator
arguments.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/a6fe58dffe553a3e79303777d3ba9c60d7613c5b.1637510255.git.christophe.jaillet@wanadoo.fr
When developping NAND controller drivers or when debugging filesystem
corruptions, it is quite common to need hacking locally into the
MTD/NAND core in order to get access to the content of the bad
blocks. Instead of having multiple implementations out there let's
provide a simple yet effective specific MTD-wide debugfs entry to fully
disable these checks on purpose.
A warning is added to inform the user when this mode gets enabled.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211118114659.1282855-1-miquel.raynal@bootlin.com
Variable ooblen is being initialized with a value that is never read.
The variable is never used after this, so it is redundant and can be
removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211205230729.79337-1-colin.i.king@gmail.com
Get rid of the static initialization of the flash parameters and
init them when parsing SFDP.
Generated a 256 Kbyte random data and did an erase, write, read back
and compare test. The flash uses for reads SPINOR_OP_READ_1_4_4_4B 0xec,
for erases SPINOR_OP_BE_4K_4B 0x21, and for writes SPINOR_OP_PP_4B 0x12.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-15-tudor.ambarus@microchip.com
Get rid of the static initialization of the flash parameters and
init them when parsing SFDP.
Generated a 256 Kbyte random data and did an erase, write, read back
and compare test. The flash uses for reads SPINOR_OP_READ_1_4_4_4B 0xec,
for erases SPINOR_OP_BE_4K_4B 0x21, and for writes SPINOR_OP_PP_1_1_4_4B
0x34.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-14-tudor.ambarus@microchip.com
s25fl256s0 does not define the SFDP tables nor implements the
RDSFDP 0x5a command. Skip the SFDP parsing in order to avoid
issuing an unsupported command to the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-13-tudor.ambarus@microchip.com
Get rid of the static initialization of the flash parameters and
init them when parsing SFDP.
Generated a 256 Kbyte random data and did an erase, write, read back
and compare test. The flash uses for reads SPINOR_OP_READ_1_4_4 0xeb,
for erases SPINOR_OP_BE_4K 0x20, and for writes SPINOR_OP_PP 0x02.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211207140254.87681-12-tudor.ambarus@microchip.com
spi_nor_setup() configures the SPI NOR memory. Setting the addr width
is too a configuration, hence we can move the spi_nor_set_addr_width()
in spi_nor_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20211207140254.87681-11-tudor.ambarus@microchip.com
New flash additions that support SFDP should be declared with
PARSE_SFDP and with all the other flags that are not SFDP
discoverable.
Keep the old way of initializing the flash, until all the flashes
are converted to use either PARSE_SFDP or SPI_NOR_SKIP_SFDP.
Flashes that declare PARSE_SFDP do not have a roll-back mechanism
because if spi_nor_parse_sfdp() returns an error it means that either
BFPT is not supported, thus SFDP is not supported and the user didn't
correctly declared the flash_info entry, or some memalloc failed.
Either way we should return an error. The rest of the SFDP tables are
optional, if one of the optional SFDP tables fails, we just continue.
We would like to get rid of the default_init() hook, so the
spi_nor_manufacturer_init_params() is not called in the new sequnce
of flash initialization.
Split spi_nor_info_init_params() in spi_nor_init_default_params()
and spi_nor_no_sfdp_init_params(). spi_nor_init_default_params() is
called for all the flashes regardless if they support SFDP or not.
spi_nor_no_sfdp_init_params() is called just for the flashes that
do not define SFDP and initializes parameters and setting solely
based on flash_info data.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-10-tudor.ambarus@microchip.com
Group NOR flags initialization. Introduce a dedicated function for
setting the fixup_flags and emphasise when those flash_info flags
should be set: when the SNOR_F_4B_OPCODES/SNOR_F_IO_MODE_EN_VOLATILE
setttings can not be discovered by SFDP for this particular flash
because the SFDP table that indicates this support is not defined
in the flash.
In case the table for his support is defined but has wrong values,
one should instead use a post_sfdp() hook to set the SNOR_F equivalent
flag.
No functional change intended in this patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-9-tudor.ambarus@microchip.com
Used to initialize the NOR flags for settings that are not defined
in the JESD216 SFDP standard, thus can not be retrieved when parsing
SFDP.
This moves the setting of SNOR_F_READY_XSR_RDY and SNOR_F_HAS_LOCK
late in the init call, without any functional change expected.
The rest of the flags were already set after the spi_nor_init_params().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-8-tudor.ambarus@microchip.com
Clarify for what the flash_info flags are used for. Split them in
four categories and a bool:
1/ FLAGS: flags that indicate support that is not defined by the JESD216
standard in its SFDP tables.
2/ NO_SFDP_FLAGS: these flags are used when the flash does not define the
SFDP tables. These flags indicate support that can be discovered via
SFDP. Used together with SPI_NOR_SKIP_SFDP flag.
3/ FIXUP_FLAGS: flags that indicate support that can be discovered
via SFDP ideally, but can not be discovered for this particular flash
because the SFDP table that indicates this support is not defined by
the flash. In case the table for this support is defined but has wrong
values, one should instead use a post_sfdp() hook to set the SNOR_F
equivalent flag.
4/ MFR_FLAGS: manufacturer private flags. Used in the manufacturer
fixup hooks to differentiate support between flashes of the same
manufacturer.
5/ PARSE_SFDP: sets info->parse_sfdp to true. All flash_info entries
that support SFDP should be converted to set info->parse_sfdp to true.
SPI NOR flashes that statically declare one of the
SPI_NOR_{DUAL, QUAD, OCTAL, OCTAL_DTR}_READ flags and do not support
the RDSFDP command are gratuiously receiving the RDSFDP command
in the attempt of parsing the SFDP tables. It is not desirable to issue
commands that are not supported, so introduce PARSE_SFDP to help on this
situation.
New flash additions/updates should be declared/updated to use either
PARSE_SFDP or SPI_NOR_SKIP_SFDP. Once all the flash_info entries are
converted to use SPI_NOR_SKIP_SFDP or PARSE_SFDP, we can get rid of the
SPI_NOR_SKIP_SFDP flag and use just the bool nor->info->parse_sfdp to
determine whether to parse SFDP or not. SPI_NOR_SKIP_SFDP flag is kept
just as a way to differentiate whether a flash is converted to the new
flags logic or not.
Support that can be discovered when parsing SFDP should not be duplicated
by explicit flags at flash declaration. All the flash parameters will be
discovered when parsing SFDP. Sometimes manufacturers wrongly define some
fields in the SFDP tables. If that's the case, SFDP data can be amended
with the fixups() hooks. It is not common, but if the SFDP tables are
entirely wrong, and it does not worth the hassle to tweak the SFDP
parameters by using the fixups hooks, or if the flash does not define the
SFDP tables at all, then statically init the flash with the
SPI_NOR_SKIP_SFDP flag and specify the rest of flash capabilities with
the flash info flags.
With time, we want to convert all flashes to use PARSE_SFDP and
stop triggering the SFDP parsing with the
SPI_NOR_{DUAL, QUAD, OCTAL*}_READ flags. Getting rid of the
SPI_NOR_{OCTAL, OCTAL_DTR}_READ trigger is easily achievable,
the rest are a long term goal.
Manufacturer specific flags like USE_CLSR, USE_FSR, SPI_NOR_XSR_RDY,
will be removed in a future series.
No functional changes intended in this patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-7-tudor.ambarus@microchip.com
Used in the manufacturer fixup hooks to differentiate support
between flashes of the same manufacturer. Not used in the
SPI NOR core.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-6-tudor.ambarus@microchip.com
spi_nor_post_sfdp_fixups() was called even when there were no SFDP
tables defined. late_init() should be instead used for flashes that
do not define SFDP tables.
Use spi_nor_post_sfdp_fixups() just to fix SFDP data. post_sfdp()
hook is as of now used just by s28hs512t, mt35xu512aba, and both
support SFDP, there's no functional change with this patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-5-tudor.ambarus@microchip.com
Used to init all the mtd_info fields. Move the mtd_info init
the last thing in the spi_nor_scan(), so that we avoid superfluous
initialization of the mtd_info fields in case of errors.
While here use common naming scheme for functions that are setting
mtd_info fields:
s/spi_nor_register_locking_ops/spi_nor_set_mtd_locking_ops
s/spi_nor_otp_init/spi_nor_set_mtd_otp_ops
The functions names are self explanatory, get rid of the comment
for the OTP function.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-4-tudor.ambarus@microchip.com
Use NOR parameters in the probe's sequence of calls, thus
nor->params->size instead of nor->mtd.size and let the mtd_info
fields be used by the mtd calls (mtd->_erase, mtd->_read, mtd->_write).
mtd_info fields should not be used during probe because we haven't
registered mtd yet. It's safe to drop xilinx's setting of nor->mtd.size,
now that we use nor->params->size in spi_nor_set_addr_width().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-3-tudor.ambarus@microchip.com
As it was before the blamed commit, s3an_nor_scan() was called
after mtd size was set with params->size, and it overwrote the mtd
size value with '8 * nor->page_size * nor->info->n_sectors' when
XSR_PAGESIZE was set. With the introduction of
s3an_post_sfdp_fixups(), we missed to update the mtd size for the
s3an flashes. Fix the mtd size by updating both nor->params->size,
(which will update the mtd_info size later on) and nor->mtd.size
(which is used in spi_nor_set_addr_width()).
Fixes: 641edddb4f ("mtd: spi-nor: Add s3an_post_sfdp_fixups()")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211207140254.87681-2-tudor.ambarus@microchip.com
Commit 5fa6863ba6 ("spi: Check we have a spi_device_id for each DT
compatible") added a test to check that every SPI driver has a
spi_device_id for each DT compatiable string defined by the driver
and warns if the spi_device_id is missing. The spi_device_ids are
missing for the dataflash driver and the following warnings are now
seen.
WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,at45
WARNING KERN SPI driver mtd_dataflash has no spi_device_id for atmel,dataflash
Fix this by adding the necessary spi_device_ids.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211130112443.107730-1-jonathanh@nvidia.com
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
The FSMC NAND controller should apply a delay after the
instruction has been issued on the bus.
The FSMC NAND controller driver did not handle this delay.
Add this waiting delay in the FSMC NAND controller driver.
Fixes: 4da712e702 ("mtd: nand: fsmc: use ->exec_op()")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-4-herve.codina@bootlin.com
When the NV-DDR interface is not supported by the NAND chip,
the value of onfi->nvddr_timing_modes is 0. In this case,
the best_mode variable value in nand_choose_best_nvddr_timings()
is -1. The last for-loop is skipped and the function returns an
uninitialized value.
If this returned value is 0, the nand_choose_best_sdr_timings()
is not executed and no 'best timing' are set. This leads the host
controller and the NAND chip working at default mode 0 timing
even if a better timing can be used.
Fix this uninitialized returned value.
nand_choose_best_sdr_timings() is pretty similar to
nand_choose_best_nvddr_timings(). Even if onfi->sdr_timing_modes
should never be seen as 0, nand_choose_best_sdr_timings() returned
value is fixed.
Fixes: a9ecc8c814 ("mtd: rawnand: Choose the best timings, NV-DDR included")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-3-herve.codina@bootlin.com
NAND_OP_CMD() expects a delay parameter in nanoseconds.
The delay value is wrongly given in milliseconds.
Fix the conversion macro used in order to set this
delay in nanoseconds.
Fixes: d7a773e881 ("mtd: rawnand: Access SDR and NV-DDR timings through a common macro")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-2-herve.codina@bootlin.com
The helper function devm_platform_ioremap_resource_xxx()
needs HAS_IOMEM enabled, so add the dependency on HAS_IOMEM.
Fixes: 5f14a8ca1b ("mtd: rawnand: denali: Make use of the helper function devm_platform_ioremap_resource_byname()")
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211109134758.417-1-caihuoqing@baidu.com
This allows an MTD device that has been unregistered to be easily
re-registered later without triggering spurious "already registered"
warnings in mtd_device_parse_register() and add_mtd_device().
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211015185049.3318-1-zev@bewilderbeest.net
mtd_device_unregister() shouldn't fail. Wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
By returning 0 in the spi remove callback a generic error message by the
spi framework (and nothing else) is suppressed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211108093153.63792-4-u.kleine-koenig@pengutronix.de
mtd_device_unregister() shouldn't fail. Wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
By returning 0 in the spi remove callback a generic error message by the
spi framework (and nothing else) is suppressed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211108093153.63792-3-u.kleine-koenig@pengutronix.de
mtd_device_unregister() shouldn't fail. Wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
By returning 0 in the spi remove callback a generic error message by the
spi framework (and nothing else) is suppressed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211108093153.63792-2-u.kleine-koenig@pengutronix.de
mtd_device_unregister() shouldn't fail. Wail loudly if it does anyhow.
This matches how other drivers (e.g. nand/raw/nandsim.c) use
mtd_device_unregister().
By returning 0 in the spi remove callback a generic error message by the
spi framework (and nothing else) is suppressed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211108093153.63792-1-u.kleine-koenig@pengutronix.de
If there is more than one mtd device which supports OTP, there will
be a kernel warning about duplicated sysfs entries and the probing will
fail. This is because the nvmem device name is not unique. Make it
unique by prepending the name of the mtd. E.g. before the name was
"user-otp", now it will be "mtd0-user-otp".
For reference the kernel splash is:
[ 4.665531] sysfs: cannot create duplicate filename '/bus/nvmem/devices/user-otp'
[ 4.673056] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.15.0-next-20211101+ #1296
[ 4.680565] Hardware name: Kontron SMARC-sAL28 (Single PHY) on SMARC Eval 2.0 carrier (DT)
[ 4.688856] Call trace:
[ 4.691303] dump_backtrace+0x0/0x1bc
[ 4.694984] show_stack+0x24/0x30
[ 4.698306] dump_stack_lvl+0x68/0x84
[ 4.701980] dump_stack+0x18/0x34
[ 4.705302] sysfs_warn_dup+0x70/0x90
[ 4.708973] sysfs_do_create_link_sd+0x144/0x150
[ 4.713603] sysfs_create_link+0x2c/0x50
[ 4.717535] bus_add_device+0x74/0x120
[ 4.721293] device_add+0x330/0x890
[ 4.724791] device_register+0x2c/0x40
[ 4.728550] nvmem_register+0x240/0x9f0
[ 4.732398] mtd_otp_nvmem_register+0xb0/0x10c
[ 4.736854] mtd_device_parse_register+0x28c/0x2b4
[ 4.741659] spi_nor_probe+0x20c/0x2e0
[ 4.745418] spi_mem_probe+0x78/0xbc
[ 4.749001] spi_probe+0x90/0xf0
[ 4.752237] really_probe.part.0+0xa4/0x320
..
[ 4.873936] mtd mtd1: Failed to register OTP NVMEM device
[ 4.894468] spi-nor: probe of spi0.0 failed with error -17
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211104134843.2642800-1-michael@walle.cc
Not the child partition should be removed from the partition list
but the partition itself. Otherwise the partition list gets broken
and any subsequent remove operations leads to a kernel panic.
Fixes: 46b5889cc2 ("mtd: implement proper partition handling")
Signed-off-by: Andreas Oetken <andreas.oetken@siemens-energy.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102172604.2921065-1-andreas.oetken@siemens-energy.com
The block layer already performs this check, no need to duplicate it in
the driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20211126121802.2090656-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All modern drivers can support extra partitions using the extended
dev_t. In fact except for the ioctl method drivers never even see
partitions in normal operation.
So remove the GENHD_FL_EXT_DEVT and allow extra partitions for all
block devices that do support partitions, and require those that
do not support partitions to explicit disallow them using
GENHD_FL_NO_PART.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211122130625.1136848-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This function is trivial, and flush_dcache_page is always defined, so
just open code it in the 2.5 callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20211117061404.331732-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The following KASAN BUG is observed when testing the rpc-if driver on
rcar-gen3:
root@rcar-gen3:~# modprobe -r rpc-if
[ 101.930146] ==================================================================
[ 101.937408] BUG: KASAN: slab-out-of-bounds in __lock_acquire+0x518/0x25d0
[ 101.944240] Read of size 8 at addr ffff0004c5be2750 by task modprobe/664
[ 101.950959]
[ 101.952466] CPU: 2 PID: 664 Comm: modprobe Not tainted 5.14.0-rc1-00342-g1a1464d7aa31 #1
[ 101.960578] Hardware name: Renesas H3ULCB board based on r8a77951 (DT)
[ 101.967120] Call trace:
[ 101.969580] dump_backtrace+0x0/0x2c0
[ 101.973275] show_stack+0x1c/0x30
[ 101.976616] dump_stack_lvl+0x9c/0xd8
[ 101.980301] print_address_description.constprop.0+0x74/0x2b8
[ 101.986071] kasan_report+0x1f4/0x26c
[ 101.989757] __asan_load8+0x98/0xd4
[ 101.993266] __lock_acquire+0x518/0x25d0
[ 101.997215] lock_acquire.part.0+0x18c/0x360
[ 102.001506] lock_acquire+0x74/0x90
[ 102.005013] _raw_spin_lock_irq+0x98/0x130
[ 102.009131] __pm_runtime_disable+0x30/0x210
[ 102.013427] rpcif_hb_remove+0x5c/0x70 [rpc_if]
[ 102.018001] platform_remove+0x40/0x80
[ 102.021771] __device_release_driver+0x234/0x350
[ 102.026412] driver_detach+0x158/0x20c
[ 102.030179] bus_remove_driver+0xa0/0x140
[ 102.034212] driver_unregister+0x48/0x80
[ 102.038153] platform_driver_unregister+0x18/0x24
[ 102.042879] rpcif_platform_driver_exit+0x1c/0x34 [rpc_if]
[ 102.048400] __arm64_sys_delete_module+0x210/0x310
[ 102.053212] invoke_syscall+0x60/0x190
[ 102.056986] el0_svc_common+0x12c/0x144
[ 102.060844] do_el0_svc+0x88/0xac
[ 102.064181] el0_svc+0x24/0x3c
[ 102.067257] el0t_64_sync_handler+0x1a8/0x1b0
[ 102.071634] el0t_64_sync+0x198/0x19c
[ 102.075315]
[ 102.076815] Allocated by task 628:
[ 102.080781]
[ 102.082280] Last potentially related work creation:
[ 102.087524]
[ 102.089022] The buggy address belongs to the object at ffff0004c5be2000
[ 102.089022] which belongs to the cache kmalloc-2k of size 2048
[ 102.101555] The buggy address is located 1872 bytes inside of
[ 102.101555] 2048-byte region [ffff0004c5be2000, ffff0004c5be2800)
[ 102.113486] The buggy address belongs to the page:
[ 102.118409]
[ 102.119908] Memory state around the buggy address:
[ 102.124711] ffff0004c5be2600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.131947] ffff0004c5be2680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.139181] >ffff0004c5be2700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.146412] ^
[ 102.152257] ffff0004c5be2780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.159491] ffff0004c5be2800: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 102.166723] ==================================================================
The above bug is caused by use of the wrong pointer in the
rpcif_disable_rpm() call. Fix the bug by using the correct pointer.
Fixes: 5de15b610f ("mtd: hyperbus: add Renesas RPC-IF driver")
Signed-off-by: George G. Davis <davis.george@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210716204935.25859-1-george_davis@mentor.com
gpmi_io clock needs to be gated off when changing the parent/dividers of
enfc_clk_root (i.MX6Q/i.MX6UL) respectively qspi2_clk_root (i.MX6SX).
Otherwise this rate change can lead to an unresponsive GPMI core which
results in DMA timeouts and failed driver probe:
[ 4.072318] gpmi-nand 112000.gpmi-nand: DMA timeout, last DMA
...
[ 4.370355] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -110
...
[ 4.375988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.381524] gpmi-nand 112000.gpmi-nand: Error in ECC-based read: -22
[ 4.387988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.393535] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
...
Other than stated in i.MX 6 erratum ERR007117, it should be sufficient
to gate only gpmi_io because all other bch/nand clocks are derived from
different clock roots.
The i.MX6 reference manuals state that changing clock muxers can cause
glitches but are silent about changing dividers. But tests showed that
these glitches can definitely happen on i.MX6ULL. For i.MX7D/8MM in turn,
the manual guarantees that no glitches can happen when changing
dividers.
Co-developed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-2-ceggers@arri.de
There is no need to explicitly set the default gpmi clock rate during
boot for the i.MX 6 since this is done during nand_detect anyway.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Cc: stable@vger.kernel.org
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-1-ceggers@arri.de
The ECC engine on the JZ4740 SoC requires the ECC data to be read before
the page; using the default page reading function does not work. Indeed,
the old JZ4740 NAND driver (removed in 5.4) did use the 'OOB first' flag
that existed back then.
Use the newly created nand_read_page_hwecc_oob_first() to address this
issue.
This issue was not found when the new ingenic-nand driver was developed,
most likely because the Device Tree used had the nand-ecc-mode set to
"hw_oob_first", which seems to not be supported anymore.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-5-paul@crapouillou.net
Move the function nand_read_page_hwecc_oob_first() (previously
nand_davinci_read_page_hwecc_oob_first()) to nand_base.c, and export it
as a GPL symbol, so that it can be used by more modules.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-4-paul@crapouillou.net
The original comment that describes the function
nand_davinci_read_page_hwecc_oob_first() is very obscure and it is hard
to understand what it is for.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-3-paul@crapouillou.net
The function nand_davinci_read_page_hwecc_oob_first() first reads the
OOB data, extracts the ECC information, programs the ECC hardware before
reading the actual data in a loop.
Right after the OOB data was read, it called nand_read_page_op() to
reset the read cursor to the beginning of the page. This caused the
first page to be read twice: in that call, and later in the loop.
Address that issue by changing the call to nand_read_page_op() to
nand_change_read_column_op(), which will only reset the read cursor.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-2-paul@crapouillou.net
The function nand_davinci_read_page_hwecc_oob_first() does read the ECC
data from the OOB area. Therefore it does not need to calculate the ECC
as it is already available.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-1-paul@crapouillou.net
spansion_post_sfdp_fixups() was called regardless if the flash defined
SFDP tables or not. A better place for this kind of parameters init is
in manufacturer's late_init() hook. post_sfdp() should be called only
when SFDP is defined. No functional change in this patch.
Instead of doing the 4b opcodes settings at manufacturer level, thus
also for every flash that will be introduced, this should be done
just where it is needed, per flash. I'll let this for other patch.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-12-tudor.ambarus@microchip.com
Setting the correct nor->mtd._write in a fixup hook was misleading,
since this is not a fixup, just a specific setting for SST, that differs
from the SPI NOR core default init.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-11-tudor.ambarus@microchip.com
post_sfdp was misleading in this case, as SFDP is not supported by
xilinx. Plus, there's no fixup here, just setting the correct
setup method, as required by xilinx parts.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-10-tudor.ambarus@microchip.com
OTP is not described in the JESD216 SFDP standard, place the
OTP ops init in late_init().
We can't get rid of the default_init() hook for winbond, as the
4byte_addr_mode is SFDP specific and will require to have all
flashes at hand, in order to check which has the SFDP tables defined,
in which case there's nothing to do if the SFDP tables are corect,
and which of the flashes do not define the SFDP tables in which case
each flash should declare a late_init() fixup.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-9-tudor.ambarus@microchip.com
Locking is not described in JESD216 SFDP standard, place the
locking init in late_init().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-8-tudor.ambarus@microchip.com
Locking is not described in JESD216 SFDP standard, place the
locking init in late_init().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-7-tudor.ambarus@microchip.com
Flash parameters init is done in a spaghetti way right now.
There is the init based on the flash_info data, then there is the
default_init() hook, then SFDP init, an intermediary post_bft(),
then post_sfdp() and a spi_nor_late_init_params(). Each method can
overwrite previuosly initialized parameters.
We want to separate what is SFDP and non-SFDP specific. late_init()
will replace the default_init() hook and will be used only to initialize
flash parameters that are not declared in the JESD216 SFDP standard, or
where SFDP tables are not defined at all.
We cut a member in the chain of initializing parameters by getting rid
of the default_init() hook, and we make it clear that everything that is
in late_init() is not covered by the SFDP tables defined by the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-6-tudor.ambarus@microchip.com
nor->page_size duplicated what nor->params->page_size indicates
for no good reason. page_size is a flash parameter of fixed value
and it is better suited to be found in nor->params->page_size.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20211029172633.886453-5-tudor.ambarus@microchip.com
"struct mtd_info mtd" is member of "struct spi_nor", there's no need
to use "mtd->priv". Get the pointer to the containing struct spi_nor
by using container_of. While here, make the function inline and
get rid of the __maybe_unused.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20211029172633.886453-3-tudor.ambarus@microchip.com
Update the description of the otp member of the
struct spi_nor_flash_parameter.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20211029172633.886453-2-tudor.ambarus@microchip.com
SPI Multi I/O Bus Controller on RZ/G2L SoC is almost identical to
the RPC-IF interface found on R-Car Gen3 SoC's.
This patch adds a new compatible string for the RZ/G2L family so
that the timing values on RZ/G2L can be adjusted.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211025205631.21151-8-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
rpcif_sw_init() can fail so make sure we check the return value
of it and on error exit rpcif_hb_probe() callback with error code.
Fixes: 5de15b610f ("mtd: hyperbus: add Renesas RPC-IF driver")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211025205631.21151-5-prabhakar.mahadev-lad.rj@bp.renesas.com
-----BEGIN PGP SIGNATURE-----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=QaFI
-----END PGP SIGNATURE-----
Merge tag 'for-5.16/drivers-2021-11-09' of git://git.kernel.dk/linux-block
Pull more block driver updates from Jens Axboe:
- Last series adding error handling support for add_disk() in drivers.
After this one, and once the SCSI side has been merged, we can
finally annotate add_disk() as must_check. (Luis)
- bcache fixes (Coly)
- zram fixes (Ming)
- ataflop locking fix (Tetsuo)
- nbd fixes (Ye, Yu)
- MD merge via Song
- Cleanup (Yang)
- sysfs fix (Guoqing)
- Misc fixes (Geert, Wu, luo)
* tag 'for-5.16/drivers-2021-11-09' of git://git.kernel.dk/linux-block: (34 commits)
bcache: Revert "bcache: use bvec_virt"
ataflop: Add missing semicolon to return statement
floppy: address add_disk() error handling on probe
ataflop: address add_disk() error handling on probe
block: update __register_blkdev() probe documentation
ataflop: remove ataflop_probe_lock mutex
mtd/ubi/block: add error handling support for add_disk()
block/sunvdc: add error handling support for add_disk()
z2ram: add error handling support for add_disk()
nvdimm/pmem: use add_disk() error handling
nvdimm/pmem: cleanup the disk if pmem_release_disk() is yet assigned
nvdimm/blk: add error handling support for add_disk()
nvdimm/blk: avoid calling del_gendisk() on early failures
nvdimm/btt: add error handling support for add_disk()
nvdimm/btt: use goto error labels on btt_blk_init()
loop: Remove duplicate assignments
drbd: Fix double free problem in drbd_create_device
nvdimm/btt: do not call del_gendisk() if not needed
bcache: fix use-after-free problem in bcache_device_free()
zram: replace fsync_bdev with sync_blockdev
...
* Remove obsolete macros only used by the old nand_ecclayout struct
* Don't remove debugfs directory if device is in use
* MAINTAINERS:
- Add entry for Qualcomm NAND controller driver
- Update the devicetree documentation path of hyperbus
MTD devices:
* block2mtd:
- Add support for an optional custom MTD label
- Minor refactor to avoid hard coded constant
* mtdswap: Remove redundant assignment of pointer eb
CFI:
* Fixup CFI on ixp4xx
Raw NAND controller drivers:
* Arasan:
- Prevent an unsupported configuration
* Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd, AMS-Delta:
- Keep the driver compatible with on-die ECC engines
* cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
* Fsmc: Fix use of SM ORDER
* Intel:
- Fix potential buffer overflow in probe
* xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk, hisi504,
gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand drivers:
* Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
* Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
SPI NOR core:
* Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers:
* Enable locking for n25q128a13
SPI NOR controller drivers:
* Use devm_platform_ioremap_resource_byname()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmGIAdEACgkQJWrqGEe9
VoQHEAgAkFvFxIOyPSwAJfyeEklWmGSh+cm+X9EqWxZ5d6iwFE3FZH4X4XiqdyVY
+rzy37o6Tp3pQVYDqxmPM8GGoHy8wYPR5h/U1IozbBaNeCJma1HyK4Sjb/cuX1eQ
23EM1pWT8N9CbRG2S9mz5C9uHcP9mImtyvU4WhTLKOEc9XGbpuj+k1cacSuEEbeF
rZklOa7tvUiOFIDfr7Kf+DfxbpYabgB2dJgWPEtZmKmefWMiODHgvBJo0MT6MKr7
kOlIkgq5zYIFRNaxApWLI3JmH9+lsw6MHBe+cCqemV6q2OZlMV/5VGFElEywJt+4
L3VmlJQpMiCEMo2Cgc1jigHKryk4Xw==
=h6o3
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"Core:
- Remove obsolete macros only used by the old nand_ecclayout struct
- Don't remove debugfs directory if device is in use
- MAINTAINERS:
- Add entry for Qualcomm NAND controller driver
- Update the devicetree documentation path of hyperbus
MTD devices:
- block2mtd:
- Add support for an optional custom MTD label
- Minor refactor to avoid hard coded constant
- mtdswap: Remove redundant assignment of pointer eb
CFI:
- Fixup CFI on ixp4xx
Raw NAND controller drivers:
- Arasan:
- Prevent an unsupported configuration
- Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd,
AMS-Delta:
- Keep the driver compatible with on-die ECC engines
- cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
- Fsmc: Fix use of SM ORDER
- Intel:
- Fix potential buffer overflow in probe
- xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk,
hisi504, gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand drivers:
- Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
- Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
SPI NOR core:
- Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers:
- Enable locking for n25q128a13
SPI NOR controller drivers:
- Use devm_platform_ioremap_resource_byname()"
* tag 'mtd/for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (50 commits)
mtd: core: don't remove debugfs directory if device is in use
MAINTAINERS: Update the devicetree documentation path of hyperbus
mtd: block2mtd: add support for an optional custom MTD label
mtd: block2mtd: minor refactor to avoid hard coded constant
mtd: fixup CFI on ixp4xx
mtd: rawnand: arasan: Prevent an unsupported configuration
MAINTAINERS: Add entry for Qualcomm NAND controller driver
mtd: rawnand: hynix: Add support for H27UCG8T2ETR-BC MLC NAND
mtd: rawnand: xway: Keep the driver compatible with on-die ECC engines
mtd: rawnand: socrates: Keep the driver compatible with on-die ECC engines
mtd: rawnand: plat_nand: Keep the driver compatible with on-die ECC engines
mtd: rawnand: pasemi: Keep the driver compatible with on-die ECC engines
mtd: rawnand: orion: Keep the driver compatible with on-die ECC engines
mtd: rawnand: mpc5121: Keep the driver compatible with on-die ECC engines
mtd: rawnand: gpio: Keep the driver compatible with on-die ECC engines
mtd: rawnand: au1550nd: Keep the driver compatible with on-die ECC engines
mtd: rawnand: ams-delta: Keep the driver compatible with on-die ECC engines
Revert "mtd: rawnand: cs553x: Fix external use of SW Hamming ECC helper"
Revert "mtd: rawnand: lpc32xx_slc: Fix external use of SW Hamming ECC helper"
Revert "mtd: rawnand: ndfc: Fix external use of SW Hamming ECC helper"
...
- Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers changes:
- Enable locking for n25q128a13
SPI NOR controller drivers changes:
- Use devm_platform_ioremap_resource_byname()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmGA9wgACgkQS1VPR6WN
FOnkZAf9E0iin+gx05X6V68NuuQ2iG+gJoHTqCL1WMvBaDbT2vr9gYgclqKAM4FO
2QL66b+zrIhmNP3qPy1HobjxpdCJo8b5PDDShR8aQ1c1RaeOfRNyK9XXsfrI8t1s
mJwIvIcqEAZLskyCotlJVzvHmyTx30RfFbtJD1hjArFUKi1vbdROhx2G1tnAMdVj
tnbRTVL6WTsrSTvgpydtJIfdZ3lS/9RnewCUjQAM9V1PlfJ3ZF4cnRsGPRArGuSb
5f9iHqK6uQtW+K+zuRke6Vf+Xrh6Qan5BZGbn5QhijSaCKgL6aAr6uQ3RDMwu4AU
G0tnqjfeaS6GVV6NV7Fay0M4CVJChA==
=Q/zo
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.16' into mtd/next
SPI NOR core changes:
- Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers changes:
- Enable locking for n25q128a13
SPI NOR controller drivers changes:
- Use devm_platform_ioremap_resource_byname()
* Remove obsolete macros only used by the old nand_ecclayout struct
* MAINTAINERS: Add entry for Qualcomm NAND controller driver
Raw NAND controller drivers:
* Arasan:
- Prevent an unsupported configuration
* Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd, AMS-Delta:
- Keep the driver compatible with on-die ECC engines
* cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
* Fsmc: Fix use of SM ORDER
* Intel:
- Fix potential buffer overflow in probe
* xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk, hisi504,
gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand driver:
* Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
* Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmGAOJQACgkQJWrqGEe9
VoTDugf/Z3rfv0A5rEZou8qKVzdLeQ2Aun3HgZZZ3NMMLYTigLiR8iQqR4fvN8KR
xivkbowMoDNgPiVABvTMhD73hPjVokGGE9/KnwY0w6/0tw+pNzkuPBSVO6uYK9Pc
d51cc8OY1Gb9DdYyQB+RI/heox1H8OYskla1lTG14hP69UAqPmj8O43o4OnW/l1T
S8NyBgMAm6YaStAKfJoDNiaDYIYNCMxQVmOB643O71xBkG30cXxPefNDe31yUFVj
b2lL1E2zQT6xc44a9tu5T9WbXBz9oj+r9JTmrAXdtqcqWnC903ap6QYttc5jLoqd
IJw25CZqZjy+/3j8smtxxmIu3kptCA==
=zb5E
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.16' into mtd/next
Core:
* Remove obsolete macros only used by the old nand_ecclayout struct
* MAINTAINERS: Add entry for Qualcomm NAND controller driver
Raw NAND controller drivers:
* Arasan:
- Prevent an unsupported configuration
* Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd, AMS-Delta:
- Keep the driver compatible with on-die ECC engines
* cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
* Fsmc: Fix use of SM ORDER
* Intel:
- Fix potential buffer overflow in probe
* xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk, hisi504,
gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand driver:
* Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
* Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
Merge misc updates from Andrew Morton:
"257 patches.
Subsystems affected by this patch series: scripts, ocfs2, vfs, and
mm (slab-generic, slab, slub, kconfig, dax, kasan, debug, pagecache,
gup, swap, memcg, pagemap, mprotect, mremap, iomap, tracing, vmalloc,
pagealloc, memory-failure, hugetlb, userfaultfd, vmscan, tools,
memblock, oom-kill, hugetlbfs, migration, thp, readahead, nommu, ksm,
vmstat, madvise, memory-hotplug, rmap, zsmalloc, highmem, zram,
cleanups, kfence, and damon)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (257 commits)
mm/damon: remove return value from before_terminate callback
mm/damon: fix a few spelling mistakes in comments and a pr_debug message
mm/damon: simplify stop mechanism
Docs/admin-guide/mm/pagemap: wordsmith page flags descriptions
Docs/admin-guide/mm/damon/start: simplify the content
Docs/admin-guide/mm/damon/start: fix a wrong link
Docs/admin-guide/mm/damon/start: fix wrong example commands
mm/damon/dbgfs: add adaptive_targets list check before enable monitor_on
mm/damon: remove unnecessary variable initialization
Documentation/admin-guide/mm/damon: add a document for DAMON_RECLAIM
mm/damon: introduce DAMON-based Reclamation (DAMON_RECLAIM)
selftests/damon: support watermarks
mm/damon/dbgfs: support watermarks
mm/damon/schemes: activate schemes based on a watermarks mechanism
tools/selftests/damon: update for regions prioritization of schemes
mm/damon/dbgfs: support prioritization weights
mm/damon/vaddr,paddr: support pageout prioritization
mm/damon/schemes: prioritize regions within the quotas
mm/damon/selftests: support schemes quotas
mm/damon/dbgfs: support quotas of schemes
...
Call bdi_unregister explicitly instead of relying on the automatic
unregistration.
Link: https://lkml.kernel.org/r/20211021124441.668816-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-10-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling.
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211015233028.2167651-10-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Move inode_to_bdi out of line to avoid having to include blkdev.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Previously, if del_mtd_device() failed with -EBUSY due to a non-zero
usecount, a subsequent call to attempt the deletion again would try to
remove a debugfs directory that had already been removed and panic.
With this change the second call can instead proceed safely.
Fixes: e8e3edb95c ("mtd: create per-device and module-scope debugfs entries")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211014203953.5424-1-zev@bewilderbeest.net
This patch adds support for an optional MTD label for mtd2block emulated
MTD devices. Useful when, e.g., testing device images using Qemu.
The following line in /etc/fstab can then be used to mount a file system
regardless if running on an embedded system, or emulated with block2mtd:
mtd:Config /mnt jffs2 noatime,nodiratime 0 0
Kernel command line syntax in the emulated case:
block2mtd.block2mtd=/dev/sda,,Config
Notice the ',,' it is the optional erase_size, which like before this
patch, defaults to PAGE_SIZE when omitted. Hence the strlen() check.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211009060955.552636-3-troglobit@gmail.com
drivers/mtd/maps/ixp4xx.c requires MTD_CFI_BE_BYTE_SWAP to be set
in order to compile.
drivers/mtd/maps/ixp4xx.c:57:4: error: #error CONFIG_MTD_CFI_BE_BYTE_SWAP required
This patch avoids the #error output by enforcing the policy in
Kconfig. Not sure if this is the right approach, but it helps doing
randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210927141045.1597593-1-arnd@kernel.org
Under the following conditions:
* after rounding up by 4 the number of bytes to transfer (this is
related to the controller's internal constraints),
* if this (rounded) amount of data is situated beyond the end of the
device,
* and only in NV-DDR mode,
the Arasan NAND controller timeouts.
This currently can happen in a particular helper used when picking
software ECC algorithms. Let's prevent this situation by refusing to use
the NV-DDR interface with software engines.
Fixes: 4edde60314 ("mtd: rawnand: arasan: Support NV-DDR interface")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211008163640.1753821-1-miquel.raynal@bootlin.com
Add support for the H27UCG8T2ETR-BC MLC NAND. The NAND is used widely
in the NTC CHIP, is an MLC type NAND, and is 8GB in size. Neither
JEDEC nor ONFI detection identifies it correctly, so the ID is added
to the nand_ids.c file. Additionally, per the datasheet this NAND
appears to use the same paired pages scheme as the Toshiba
TC58TEG5DCLTA00 (dist3), so add support for that to enable use in
SLC emulation mode.
Tested on a NTC CHIP the device is able to write to a ubifs formatted
partition, and then have U-Boot (with proposed patches) boot from a
kernel located on that ubifs formatted partition.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210930162402.344-1-macroalpha82@gmail.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: d525914b5b ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Cc: Jan Hoffmann <jan@3e8.eu>
Cc: Kestrel seventyfour <kestrelseventyfour@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-10-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 612e048e6a ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-8-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 8fc6f1f042 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-7-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 553508cec2 ("mtd: rawnand: orion: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-6-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 6dd09f775b ("mtd: rawnand: mpc5121: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-5-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: f6341f6448 ("mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-4-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: dbffc8ccdf ("mtd: rawnand: au1550: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-3-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 59d9347332 ("mtd: rawnand: ams-delta: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-2-miquel.raynal@bootlin.com
This reverts commit 56a8d3fd1f.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-9-miquel.raynal@bootlin.com
This reverts commit c4b7d7c480.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-8-miquel.raynal@bootlin.com
This reverts commit 3e09c02525.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-7-miquel.raynal@bootlin.com
This reverts commit 46fcb57e6b.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-6-miquel.raynal@bootlin.com
This reverts commit 6a4c5ada57.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-5-miquel.raynal@bootlin.com
This reverts commit 3d227a0b0c.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-4-miquel.raynal@bootlin.com
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
Enhancing the implementation of the rawnand_ecc_sw_* helpers to support
both cases, when the ECC object is instantiated and when it is not is a
quite elegant way to solve this situation. This way, we can still use
the existing and exported rawnand helpers while avoiding the need for
each driver to declare its own helper.
Following this change, most of the fixes sent in [2] can now be safely
reverted. Only the fsmc fix will need to be kept because there is
actually something specific to the driver to do in its ->correct()
helper.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-3-miquel.raynal@bootlin.com
The introduction of the generic ECC engine API lead to a number of
changes in various drivers which broke some of them. Here is a typical
example: I expected the SM_ORDER option to be handled by the Hamming ECC
engine internals. Problem: the fsmc driver does not instantiate (yet) a
real ECC engine object so we had to use a 'bare' ECC helper instead of
the shiny rawnand functions. However, when not intializing this engine
properly and using the bare helpers, we do not get the SM ORDER feature
handled automatically. It looks like this was lost in the process so
let's ensure we use the right SM ORDER now.
Fixes: ad9ffdce45 ("mtd: rawnand: fsmc: Fix external use of SW Hamming ECC helper")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-2-miquel.raynal@bootlin.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210901074307.9733-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210901074259.9683-1-caihuoqing@baidu.com
hisi_spi_nor_probe() invokes clk_disable_unprepare() on all paths after
successful call of clk_prepare_enable(). Besides, the clock is enabled by
hispi_spi_nor_prep() and disabled by hispi_spi_nor_unprep(). So at remove
time it is not possible to have the clock enabled. The patch removes
excessive clk_disable_unprepare() from hisi_spi_nor_remove().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: e523f11141 ("mtd: spi-nor: add hisilicon spi-nor flash controller driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210709144529.31379-1-novikov@ispras.ru
As 4bit block protection patchset for some micron models are merged,
n25q128a13 also uses 4 bit Block Protection scheme, so enable locking
for it. Tested it on n25q128a13, the locking functions work well.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210628211729.3625017-1-jonathan.lemon@gmail.com
None of supported Samsung Exynos4 SoCs (Exynos4210, Exynos4412) seem to
use OneNAND driver so drop it. Describe better which driver applies to
which SoC, to make configuring kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210924133223.111930-1-krzysztof.kozlowski@canonical.com
The pointer eb is being assigned a value that is never read, it is
being updated later on. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210910120023.46308-1-colin.king@canonical.com
From QPIC V2 onwards there is a separate register to read
last code word "QPIC_NAND_READ_LOCATION_LAST_CW_n".
qcom_nandc_read_cw_raw() is used to read only one code word
at a time. If we will configure number of code words to 1 in
in QPIC_NAND_DEV0_CFG0 register then QPIC controller thinks
its reading the last code word, since from QPIC V2 onwards
we are having separate register to read the last code word,
we have to configure "QPIC_NAND_READ_LOCATION_LAST_CW_n"
register to fetch data from controller buffer to system
memory.
Fixes: 503ee5aad4 ("mtd: rawnand: qcom: update last code word register")
Cc: stable@kernel.org
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1630998357-1359-1-git-send-email-mdalam@codeaurora.org
ebu_nand_probe() read the value of u32 variable "cs" from the device
firmware description and used it as the index for array ebu_host->cs
that can contain MAX_CS (2) elements at most. That could result in
a buffer overflow and various bad consequences later.
Fix the potential buffer overflow by restricting values of "cs" with
MAX_CS in probe.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210903082653.16441-1-novikov@ispras.ru
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074252.9633-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074245.9583-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074237.9533-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074230.9483-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074222.9433-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074215.9383-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074207.9333-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074200.9283-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074153.9233-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074145.9183-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074138.9133-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074130.9083-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074123.9033-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074116.8983-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074108.8933-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074031.8883-1-caihuoqing@baidu.com
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-10-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* blkdevs:
- Simplify the refcounting in blktrans_{open, release}
- Simplify blktrans_getgeo
- Remove blktrans_ref_mutex
- Simplify blktrans_dev_get
- Use lockdep_assert_held
- Don't hold del_mtd_blktrans_dev in blktrans_{open, release}
* ftl:
- Don't cast away the type when calling add_mtd_blktrans_dev
- Don't cast away the type when calling add_mtd_blktrans_dev
- Use container_of() rather than cast
- Fix use-after-free
- Add discard support
- Allow use of MTD_RAM for testing purposes
* concat:
- Check _read, _write callbacks existence before assignment
- Judge callback existence based on the master
* maps:
- Maps: remove dead MTD map driver for PMC-Sierra MSP boards
* mtdblock:
- Warn if added for a NAND device
- Add comment about UBI block devices
- Update old JFFS2 mention in Kconfig
* partitions:
- Redboot: convert to YAML
NAND core changes:
* Repair Miquel Raynal's email address in MAINTAINERS
* Fix a couple of spelling mistakes in Kconfig
* bbt: Skip bad blocks when searching for the BBT in NAND
* Remove never changed ret variable
Raw NAND changes:
* cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
* intel: Fix error handling in probe
* omap: Fix kernel doc warning on 'calcuate' typo
* gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
* Properly fill the OOB area.
* Fix comment
SPI-NAND drivers changes:
* macronix: Add Quad support for serial NAND flash
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmExS1gACgkQJWrqGEe9
VoSZcAf/SsUDpp/lqc+no4R+eUR/CWrbr3AKu2JjjgCJt0HK++Fy8LQU3FEjn9E8
CNBWYqIVVit1XhqGu192wh0ESsHGlNwjicB3Ul4/RFFC4WKs68kQe0gQrU6z/95V
jaTOW+B7PZh6MFbQROUVI97Cs3OTd8vCE3L2SgIW6krk8tnOEyddlgFsWLISjk6g
Ut1I473653fJAcr5OXEFJLWF+01q2azR9AiAkfKC47IUekTRJqjK2YJpAhsdf4hi
xqazp79sbcNXSHCgOOQv4/f03+SAiufRcNgztwrSWw2fdCg0csBC9ACwmdhhGGfd
7uFn+/Q3sVDOKTN7aAWW1KnykKXsJw==
=JFrk
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD changes:
- blkdevs:
- Simplify the refcounting in blktrans_{open, release}
- Simplify blktrans_getgeo
- Remove blktrans_ref_mutex
- Simplify blktrans_dev_get
- Use lockdep_assert_held
- Don't hold del_mtd_blktrans_dev in blktrans_{open, release}
- ftl:
- Don't cast away the type when calling add_mtd_blktrans_dev
- Don't cast away the type when calling add_mtd_blktrans_dev
- Use container_of() rather than cast
- Fix use-after-free
- Add discard support
- Allow use of MTD_RAM for testing purposes
- concat:
- Check _read, _write callbacks existence before assignment
- Judge callback existence based on the master
- maps:
- Maps: remove dead MTD map driver for PMC-Sierra MSP boards
- mtdblock:
- Warn if added for a NAND device
- Add comment about UBI block devices
- Update old JFFS2 mention in Kconfig
- partitions:
- Redboot: convert to YAML
NAND core changes:
- Repair Miquel Raynal's email address in MAINTAINERS
- Fix a couple of spelling mistakes in Kconfig
- bbt: Skip bad blocks when searching for the BBT in NAND
- Remove never changed ret variable
Raw NAND changes:
- cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
- intel: Fix error handling in probe
- omap: Fix kernel doc warning on 'calcuate' typo
- gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
- Properly fill the OOB area.
- Fix comment
SPI-NAND drivers changes:
- macronix: Add Quad support for serial NAND flash"
* tag 'mtd/for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (30 commits)
mtd: rawnand: cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
mtd_blkdevs: simplify the refcounting in blktrans_{open, release}
mtd_blkdevs: simplify blktrans_getgeo
mtd_blkdevs: remove blktrans_ref_mutex
mtd_blkdevs: simplify blktrans_dev_get
mtd/rfd_ftl: don't cast away the type when calling add_mtd_blktrans_dev
mtd/ftl: don't cast away the type when calling add_mtd_blktrans_dev
mtd_blkdevs: use lockdep_assert_held
mtd_blkdevs: don't hold del_mtd_blktrans_dev in blktrans_{open, release}
mtd: rawnand: intel: Fix error handling in probe
mtd: mtdconcat: Check _read, _write callbacks existence before assignment
mtd: mtdconcat: Judge callback existence based on the master
mtd: maps: remove dead MTD map driver for PMC-Sierra MSP boards
mtd: rfd_ftl: use container_of() rather than cast
mtd: rfd_ftl: fix use-after-free
mtd: rfd_ftl: add discard support
mtd: rfd_ftl: allow use of MTD_RAM for testing purposes
mtdblock: Warn if added for a NAND device
mtd: spinand: macronix: Add Quad support for serial NAND flash
mtdblock: Add comment about UBI block devices
...
* Repair Miquel Raynal's email address in MAINTAINERS
* Fix a couple of spelling mistakes in Kconfig
* bbt: Skip bad blocks when searching for the BBT in NAND
* Remove never changed ret variable
Raw NAND changes:
* cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
* intel: Fix error handling in probe
* omap: Fix kernel doc warning on 'calcuate' typo
* gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
* Properly fill the OOB area.
* Fix comment
SPI-NAND drivers changes:
* macronix: Add Quad support for serial NAND flash
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmExSXUACgkQJWrqGEe9
VoT/9wf7BJ60D3eKfnIPAnZsMgEiaLzlYfaA/z+YCX+O08mHvtApm9RLIievhZ01
+30le9U275AFDGZS5DgmY4Gtbkh5OI5YbgVqFqc4Ev3IJ2pNb7ZdPAjO/Hc5ng8O
9sTPhLr/ZknpmJu6aclCc9+C/lvAZHBQg6nYhstrljRihYJMxNmE+n3/5hveYNCX
fhZIz5uGhMzPwZSJoBMedumJ/kb/VSgznBltc+UubRr/s2ZJ7vAzjG6vptKV7Yrj
/65NyZnKiXOwVdD5TNqnsOKYA3TBN6QPG5Fz/wR/0A2R/c/qQhTTnztU5tLkSTCK
sRiaeUlyxaJcNwer7T+pvgZzyXXAhw==
=iJ+f
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.15' into mtd/next
NAND core changes:
* Repair Miquel Raynal's email address in MAINTAINERS
* Fix a couple of spelling mistakes in Kconfig
* bbt: Skip bad blocks when searching for the BBT in NAND
* Remove never changed ret variable
Raw NAND changes:
* cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
* intel: Fix error handling in probe
* omap: Fix kernel doc warning on 'calcuate' typo
* gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
* Properly fill the OOB area.
* Fix comment
SPI-NAND drivers changes:
* macronix: Add Quad support for serial NAND flash
A successful 'init_rs_non_canonical()' call should be balanced by a
corresponding 'free_rs()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: 8c61b7a7f4 ("[MTD] [NAND] Use rslib for CAFÉ ECC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/fd313d3fb787458bcc73189e349f481133a2cdc9.1629532640.git.christophe.jaillet@wanadoo.fr
Always grab a reference to the mtd_blktrans_dev in ->open instead of
just on the first open, and do away with the additional temporary
references in ->open and ->release.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210823073359.705281-9-hch@lst.de
No need to grab a mtd_blktrans_dev given that ->open already holds one
and ->getgeo can only be called on an open disk.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210823073359.705281-8-hch@lst.de
blktrans_ref_mutex is not actually needed. The kref is serialized
internally, and devnum assignment in add_mtd_blktrans_dev happens before
the disk is added and thus any of the block_device_operations methods
otherwise using it are called. It is also already serialized by the
global mtd_table_mutex.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210823073359.705281-7-hch@lst.de
->private_data is set before the disk is added and never cleared, so don't
bother trying to handle a NULL pointer there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210823073359.705281-6-hch@lst.de
There is nothing that this protects against except for slightly reducing
the window when new opens can appear just before calling del_gendisk.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210823073359.705281-2-hch@lst.de
ebu_nand_probe() did not invoke ebu_dma_cleanup() and
clk_disable_unprepare() on some error handling paths. The patch fixes
that.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817092930.23040-1-novikov@ispras.ru
Since 2431c4f5b4 ("mtd: Implement mtd_{read,write}() as wrappers
around mtd_{read,write}_oob()") don't allow _write|_read and
_write_oob|_read_oob existing at the same time, we should check the
existence of callbacks "_read and _write" from subdev's master device
(We can trust master device since it has been registered) before
assigning, otherwise following warning occurs while making
concatenated device:
WARNING: CPU: 2 PID: 6728 at drivers/mtd/mtdcore.c:595
add_mtd_device+0x7f/0x7b0
Fixes: 2431c4f5b4 ("mtd: Implement mtd_{read,write}() around ...")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817114857.2784825-3-chengzhihao1@huawei.com
Since commit 46b5889cc2c5("mtd: implement proper partition handling")
applied, mtd partition device won't hold some callback functions, such
as _block_isbad, _block_markbad, etc. Besides, function mtd_block_isbad()
will get mtd device's master mtd device, then invokes master mtd device's
callback function. So, following process may result mtd_block_isbad()
always return 0, even though mtd device has bad blocks:
1. Split a mtd device into 3 partitions: PA, PB, PC
[ Each mtd partition device won't has callback function _block_isbad(). ]
2. Concatenate PA and PB as a new mtd device PN
[ mtd_concat_create() finds out each subdev has no callback function
_block_isbad(), so PN won't be assigned callback function
concat_block_isbad(). ]
Then, mtd_block_isbad() checks "!master->_block_isbad" is true, will
always return 0.
Reproducer:
// reproduce.c
static int __init init_diy_module(void)
{
struct mtd_info *mtd[2];
struct mtd_info *mtd_combine = NULL;
mtd[0] = get_mtd_device_nm("NAND simulator partition 0");
if (!mtd[0]) {
pr_err("cannot find mtd1\n");
return -EINVAL;
}
mtd[1] = get_mtd_device_nm("NAND simulator partition 1");
if (!mtd[1]) {
pr_err("cannot find mtd2\n");
return -EINVAL;
}
put_mtd_device(mtd[0]);
put_mtd_device(mtd[1]);
mtd_combine = mtd_concat_create(mtd, 2, "Combine mtd");
if (mtd_combine == NULL) {
pr_err("combine failed\n");
return -EINVAL;
}
mtd_device_register(mtd_combine, NULL, 0);
pr_info("Combine success\n");
return 0;
}
1. ID="0x20,0xac,0x00,0x15"
2. modprobe nandsim id_bytes=$ID parts=50,100 badblocks=100
3. insmod reproduce.ko
4. flash_erase /dev/mtd3 0 0
libmtd: error!: MEMERASE64 ioctl failed for eraseblock 100 (mtd3)
error 5 (Input/output error)
// Should be "flash_erase: Skipping bad block at 00c80000"
Fixes: 46b5889cc2 ("mtd: implement proper partition handling")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817114857.2784825-2-chengzhihao1@huawei.com
Commit 1b00767fd8 ("MIPS: Remove PMC MSP71xx platform") removes the
config PMC_MSP in ./arch/mips/Kconfig.
Hence, since then, the corresponding MTD map driver for PMC-Sierra MSP
boards is dead code. Remove this dead driver.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817104531.12675-1-lukas.bulwahn@gmail.com
del_mtd_blktrans_dev() will kfree part, so after this call both part and
dev point to freed memory. Move the call to avoid use-after-free.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210807214538.14484-5-sean@mess.org
I proposed this change 16 years ago before discard was a feature in
the block layer: https://lwn.net/Articles/162776/
Now that the block layer has discard, we can finally merge this change.
Discard is also known as trim. By implementing discard, both fstrim and
the discard filesystem option can be used.
Implementing discard in the ftl means that when files are removed, there
is less data in the ftl mapping. This means less stuff to move around for
erasing and also less erasing to do; this means improved wear levelling
and improved performance.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210807214538.14484-3-sean@mess.org
This allows the rfd_ftl to be used with the mtdram module, so we can
test different mtd sizes and test the rfd_ftl on machines without a
physical nor flash device.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210807214538.14484-2-sean@mess.org
There is a surprisingly large number of tutorials
that suggest using mtdblock to mount SquashFS filesystems
on flash devices, including NAND devices.
This approach is suboptimal than using UBI. If the flash device
is NAND, this is specially true, due to wear leveling, bit-flips and
badblocks. In this case UBI is strongly preferred, so be nice to users
and print a warning suggesting to consider UBI block, if mtdblock
is added for a NAND device.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210801234509.18774-8-ezequiel@collabora.com
Adding FLAG "SPINAND_HAS_QE_BIT" for Quad mode support on Macronix
Serial Flash.
Validated via normal(default) and QUAD mode by read, erase, read back,
on Xilinx Zynq PicoZed FPGA board which included Macronix
SPI Host(drivers/spi/spi-mxic.c).
Signed-off-by: Jaime Liao <jaimeliao@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1628472472-32008-1-git-send-email-jaimeliao@mxic.com.tw
There is a surprisingly large number of tutorials
that suggest using mtdblock to mount SquashFS filesystems
on flash devices, including NAND devices.
Given this approach is suboptimal than using UBI, and given
the UBI block device layer was introduced many years ago
specifically with this use case in mind, add a small
comment inviting users and developers to consider UBI block.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210801234509.18774-7-ezequiel@collabora.com
JFFS2 can be mounted without 'mtdblock' since
a really, really long time. Some git-log
archaeology shows that in 2006 it was possible
to use 'root=' to mount a JFFS2 rootfs:
commit e9482b4374
Author: Joern Engel <joern@wh.fh-wedel.de>
Date: Tue May 30 14:25:46 2006 +0200
[MTD] Allow alternate JFFS2 mount variant for root filesystem.
With this patch, "root=mtd3" and "root=mtd:foo" work for a JFFS2 rootfs.
However, there are still plenty of tutorials that mention
mtdblock, so users are still taking this route. Update the Kconfig
to reflect this is no longer needed.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210801234509.18774-6-ezequiel@collabora.com
The ret variable used for returning value in the function
`meson_nfc_rw_cmd_prepare_and_execute` is never change after initialising.
Therefore, we can remove it safely and return 0 at the end of the function.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210803113300.24230-1-wangborong@cdjrlc.com
Fix a trivial typo which is reported after enabling W=1 level of warnings:
drivers/mtd/nand/raw/omap2.c:927: warning: expecting prototype
for omap_calcuate_ecc(). Prototype was for omap_calculate_ecc() instead
Signed-off-by: Vladimir Molokov <vladimir@molokov.se>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210801205909.7102-1-vladimir@molokov.se
The comment in spinand_write_to_cache_op() says that
spinand_ondie_ecc_prepare_io_req() should 0xff fill the OOB
area but it doesn't.
This causes the OOB area to get filled with zeros
and anytime the first page in a block the bad block marker
is cleared and it becomes a bad block on the next boot.
This was observed on Longsys FORSEE branded parts and
might be specific to these parts.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210617110842.2358461-1-daniel@0x0f.com
Due to 14f97f0b8e, the rawnand platforms without "secure-regions"
property defined in DT fails to probe. The issue is,
of_get_nand_secure_regions() errors out if
of_property_count_elems_of_size() returns a negative error code.
If the "secure-regions" property is not present in DT, then also we'll
get -EINVAL from of_property_count_elems_of_size() but it should not
be treated as an error for platforms not declaring "secure-regions"
in DT.
So fix this behaviour by checking for the existence of that property in
DT and return 0 if it is not present.
Fixes: 14f97f0b8e ("mtd: rawnand: Add a check in of_get_nand_secure_regions()")
Reported-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Tested-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210727062813.32619-1-manivannan.sadhasivam@linaro.org
There is a lock hierarchy of major_names_lock --> mtd_table_mutex. One
existing chain is as follows:
1. major_names_lock --> loop_ctl_mutex (when blk_request_module calls
loop_probe)
2. loop_ctl_mutex --> bdev->bd_mutex (when loop_control_ioctl calls
loop_remove, which then calls del_gendisk)
3. bdev->bd_mutex --> mtd_table_mutex (when blkdev_get_by_dev calls
__blkdev_get, which then calls blktrans_open)
Since unregister_blkdev grabs the major_names_lock, we need to call it
outside the critical section for mtd_table_mutex, otherwise we invert
the lock hierarchy.
Reported-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210717100719.728829-1-desmondcheongzx@gmail.com
The allocation for cmd is not being kfree'd on the return leading to
a memory leak. Fix this by kfree'ing it.
Addresses-Coverity: ("Resource leak")
Fixes: 88d1250267 ("mtd: devices: add support for microchip 48l640 EERAM")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210712145214.101377-1-colin.king@canonical.com
The blocks containing the bad block table can become bad as well. So
make sure to skip any blocks that are marked bad when searching for the
bad block table.
Otherwise in very rare cases where two BBT blocks wear out it might
happen that an obsolete BBT is used instead of a newer available
version.
This only applies to drivers which make use of a bad block marker in flash.
Other drivers won't be able to identify bad BBT blocks and thus can't skip
these.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210625123821.207458-1-s.riedmueller@phytec.de
Erasing an AMD linear flash card (AM29F016D) crashes after the first
sector has been erased. Likewise, writing to it crashes after two bytes
have been written. The reason is a missing check for a null pointer -
the cmdset_priv field is not set for this type of card.
Fixes: 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling status register")
Signed-off-by: Andreas Persson <andreasp56@outlook.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/DB6P189MB05830B3530B8087476C5CFE4C1159@DB6P189MB0583.EURP189.PROD.OUTLOOK.COM
There are flash drivers which registers the OTP callbacks although the
flash doesn't support OTP regions and return -ENODATA for these
callbacks if there is no OTP. If this happens, the probe of the whole
flash will fail. Fix it by handling the ENODATA return code and skip
the OTP region nvmem setup.
Fixes: 4b361cfa86 ("mtd: core: add OTP nvmem provider support")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210707135359.32398-1-michael@walle.cc
Smatch complains that zero length read/writes will lead to an
uninitalized return value. I don't know if that's possible, but
it's nicer to return a zero literal anyway so let's do that.
Fixes: 88d1250267 ("mtd: devices: add support for microchip 48l640 EERAM")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YMyir961W28TX5dT@mwanda
Syzbot reported a circular locking dependency:
https://syzkaller.appspot.com/bug?id=7bd106c28e846d1023d4ca915718b1a0905444cb
This happens because of the following lock dependencies:
1. loop_ctl_mutex -> bdev->bd_mutex (when loop_control_ioctl calls
loop_remove, which then calls del_gendisk; this also happens in
loop_exit which eventually calls loop_remove)
2. bdev->bd_mutex -> mtd_table_mutex (when blkdev_get_by_dev calls
__blkdev_get, which then calls blktrans_open)
3. mtd_table_mutex -> major_names_lock (when register_mtd_blktrans
calls __register_blkdev)
4. major_names_lock -> loop_ctl_mutex (when blk_request_module calls
loop_probe)
Hence there's an overall dependency of:
loop_ctl_mutex ----------> bdev->bd_mutex
^ |
| |
| v
major_names_lock <--------- mtd_table_mutex
We can break this circular dependency by holding mtd_table_mutex only
for the required critical section in register_mtd_blktrans. This
avoids the mtd_table_mutex -> major_names_lock dependency.
Reported-and-tested-by: syzbot+6a8a0d93c91e8fbf2e80@syzkaller.appspotmail.com
Co-developed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210617160904.570111-1-desmondcheongzx@gmail.com
Check for whether of_property_count_elems_of_size() returns a negative
error code.
Fixes: 13b8976827 ("mtd: rawnand: Add support for secure regions in NAND memory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YMtQFXE0F1w7mUh+@mwanda
- Fix for a race xattr list and modification
- Various minor fixes (spelling, return codes, ...)
-----BEGIN PGP SIGNATURE-----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=2Wk7
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBIFS updates from Richard Weinberger:
- Fix for a race xattr list and modification
- Various minor fixes (spelling, return codes, ...)
* tag 'for-linus-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: Set/Clear I_LINKABLE under i_lock for whiteout inode
ubifs: Fix spelling mistakes
ubifs: Remove ui_mutex in ubifs_xattr_get and change_xattr
ubifs: Fix races between xattr_{set|get} and listxattr operations
ubifs: fix snprintf() checking
ubifs: journal: Fix error return code in ubifs_jnl_write_inode()
* Convert list_for_each to entry variant
* Use MTD_DEVICE_ATTR_RO/RW() helper macros
* Remove unnecessary OOM messages
* Potential NULL dereference in mtd_otp_size()
* Fix freeing of otp_info buffer
* Create partname and partid debug files for child MTDs
* tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
* Add OTP NVMEM provider support
* Allow specifying of_node
* Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
* Convert ti,am654-hbmc.txt to YAML schema
* spi-nor: add otp property
* Add OTP bindings
* add YAML schema for the generic MTD bindings
* Add brcm,trx-magic
MTD device drivers changes:
* Add support for microchip 48l640 EERAM
* Remove superfluous "break"
* sm_ftl:
- Fix alignment of block comment
* nftl:
- Return -ENOMEM when kmalloc failed
* nftlcore:
- Remove set but rewrite variables
* phram:
- Fix error return code in phram_setup()
* plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
* Qcom:
- Fix leaking of partition name
* Redboot:
- Fix style issues
- Seek fis-index-block in the right node
* trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
* Ability to dump SFDP tables via sysfs
* Support for erasing OTP regions on Winbond and similar flashes
* Few API doc updates and fixes
* Locking support for MX25L12805D
SPI NOR controller drivers changes:
* Use SPI_MODE_X_MASK in nxp-spifi
* Intel Alder Lake-M SPI serial flash support
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmDcT+IACgkQJWrqGEe9
VoT5Sgf/dt92XA5K2SYNh58KPUwemB9DtkukmniGjo9AqSQwuzHxik3ITHBbFvwP
cSj5PAGoI+zpc+VQz+XuZF1Bsmxaqhy5c0aaJ9TZai2W6keB91in7nJPAhmAI5o2
4zhtAZ9qKp4pOwhFqn6jTd5+l38ok50go3HB4Ibw4UlLuvbUEv11DUcXGKnaAadH
tmXZALf65YAJVruPb4yw+cv7BVVgOPQL8C8ILtsrue7Zgya3JT1205Zbfdjo+X0v
Kl2gh7gGh1YLqzuLLBDUiDnfLIfiu/WTnPqxtqCULR9cLG4oXybXHZe9OsrP8E+P
T68+K8VvT5LKbGh47/OoUfLvrDguCA==
=XVaS
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Convert list_for_each to entry variant
- Use MTD_DEVICE_ATTR_RO/RW() helper macros
- Remove unnecessary OOM messages
- Potential NULL dereference in mtd_otp_size()
- Fix freeing of otp_info buffer
- Create partname and partid debug files for child MTDs
- tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
- Add OTP NVMEM provider support
- Allow specifying of_node
- Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
- Convert ti,am654-hbmc.txt to YAML schema
- spi-nor: add otp property
- Add OTP bindings
- add YAML schema for the generic MTD bindings
- Add brcm,trx-magic
MTD device drivers changes:
- Add support for microchip 48l640 EERAM
- Remove superfluous "break"
- sm_ftl:
- Fix alignment of block comment
- nftl:
- Return -ENOMEM when kmalloc failed
- nftlcore:
- Remove set but rewrite variables
- phram:
- Fix error return code in phram_setup()
- plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
- Qcom:
- Fix leaking of partition name
- Redboot:
- Fix style issues
- Seek fis-index-block in the right node
- trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
- Allow SDR timings to be nacked
- Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing
set.
- Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
- Update dead URL
- Silence static checker warning in nand_setup_interface()
- BBT:
- Fix corner case in bad block table handling
- onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
- Atmel:
- Ensure the data interface is supported.
- Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
- brcmnand:
- Convert bindings to json-schema
- OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
- PL35X:
- New driver
- QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
- Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in
marvell_nfc_resume()
- R852:
- Use DEVICE_ATTR_RO() helper macro
- MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
- HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
- Light reorganisation for the introduction of a core resume handler
- Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
- Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support"
* tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (125 commits)
mtd: spi-nor: remove redundant continue statement
mtd: rawnand: omap: Add larger page NAND chips support
mtd: rawnand: omap: Various style fixes
mtd: rawnand: omap: Check return values
mtd: rawnand: omap: Rename a macro
mtd: rawnand: omap: Aggregate the HW configuration of the ELM
mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller
dt-bindings: mtd: pl353-nand: Describe this hardware controller
MAINTAINERS: Add PL353 NAND controller entry
mtd: rawnand: qcom: avoid writing to obsolete register
mtd: rawnand: marvell: Minor documentation correction
mtd: rawnand: r852: use DEVICE_ATTR_RO() helper macro
mtd: spinand: add SPI-NAND MTD resume handler
mtd: spinand: Add spinand_init_flash() helper
mtd: spinand: add spinand_read_cfg() helper
mtd: rawnand: marvell: add missing clk_disable_unprepare() on error in marvell_nfc_resume()
mtd: rawnand: arasan: Finer grain NV-DDR configuration
mtd: rawnand: arasan: Rename the data interface register
mtd: rawnand: onfi: Fix endianness when reading NV-DDR values
mtd: rawnand: arasan: Use the right DMA mask
...
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAmDVedQQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW45dXB/9Cn4xhHr73JZX54XDXQIgR7cFGbgXzZI+W
nrzLsCCpt0RrVwYQBXv8f6IY7u4uEgH+dhsXMruY+gYDh+NJoj9REMRr3PwWhH5o
R/ajQsDsBuGmtQ+I8RDpHYCQaNtgHqpnBQ+qmErbdK3FMxOyQ9gQkDC5097NDu4e
QXTaMJbRHsxTt8U7qRO/3XIEW10GHq33gftBcZD/DrKcTIO9GT6GGi9aGN9YPsv4
zDpjgOjZyqzJndgHavTQKxVC9csuQIUFcA2fgHO3rEaiF/TLUXemJAmrEMziVDS2
7c8KgtAssHRJdjCqUn6A0/JomNdxFzGPVN2bWf4/aLgnacXmn0Xe
=acH1
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.14' into mtd/next
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmDS290ACgkQJWrqGEe9
VoS77wgAgKnqfFwbqzdSecVmXai9roSNHi/aMpVJvvLHSTCV35iCcNNtrz0Jno56
t/8twVPPZUI6f3vPXk5+NjKRCb8Oif3oU+tNxqG6mwzrBRf5R80pYCMm+HGPWZaK
+MolqGAbgFO088DTK5fGNtmbnb5fPT174RKRBGEH5NgK5M1q95uF8fIjBXDcjVe2
hvAyoqqC7i/bp40sxRtglgBpYYz+KUjCX11JvJPa5IuVU+8ezZSKJLSo5/CtgIKJ
mRQ8p8myiUjZngcnebjTrAA5AwQ13ai9ofKG0pHkdxwOq4lSRNgKou0Hk5+oq+s0
BFEuXnUrdnJNU7+XV+kAqBoT6WOFzg==
=I/9X
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
Use normal block device I/O path for pstore/blk. (Christoph Hellwig,
Kees Cook, Pu Lehui)
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAmDaKjAWHGtlZXNjb29r
QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJj5HEACHiIyjZoWDGtpdaV/GumREeKoH
UaeqCDZHNjC0AsMGSPuyifAvUHplFH9LPEHsQuvob9kSyuns2ZMDzEeWVIQzDSYI
yFAaxjqP+H9mwR0QLWZFyOv/RySPahMX8cQJyRe9mt3rBWMrK/dVI51GOG69qad7
Eb1Z4GCXz05EToWdqUK5DHlTNirbZdyAfeqdWR9Ir4zrK47SFLe4SDf7mzoySCXc
8U2yAJkaSQGwX+aVh0pgPM+nkYmf26O4iqW+G3blTKap4nxwefUJHxtYkSaiBQPH
rqNVo9hnk4LnXxJQudPmuVWMahK4OszeSpApmcok3jCZ5+/2ZPPxFYiLE4kGquTh
ulMVlECDMcc3WC7+HLYmbbg78l1K4fTTdSlcg9uXN0c6M4X+0WgLvifCJyVADQkF
twwGu06bszqCjbg+dCrabI/e/nDltcc6/T9jVFYmEwckVu0OVP9Y8DndELxngqi1
NTm+h7ArCQQtO+vm7Eeg08fqZBj4jGCXLGyPB0qI/k+YMbhq3YrGX4uoajpFUz5s
2k1M/JwOhqPPUiZJqGCxXKkXKDbrmiE2aLRoiSsSwlxL/8bqCCaXi0sc58pWUGci
93RWEWF6fZnfD4oLnzmWrQpYJHpzckoqzn8DmPQx9ztRjixN3RX/fcpyRdaaYPq9
btlK81xRoPVyqmH+7A==
=ul9O
-----END PGP SIGNATURE-----
Merge tag 'pstore-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"Use normal block device I/O path for pstore/blk. (Christoph Hellwig,
Kees Cook, Pu Lehui)"
* tag 'pstore-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore/blk: Include zone in pstore_device_info
pstore/blk: Fix kerndoc and redundancy on blkdev param
pstore/blk: Use the normal block device I/O path
pstore/blk: Move verify_size() macro out of function
pstore/blk: Improve failure reporting
The continue statement at the end of a for-loop has no effect,
invert the if expression and remove the continue.
Addresses-Coverity: ("Continue has no effect")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The snprintf() function returns the number of characters (not
counting the NUL terminator) that it would have printed if we
had space.
This buffer has UBIFS_DFS_DIR_LEN characters plus one extra for
the terminator. Printing UBIFS_DFS_DIR_LEN is okay but anything
higher will result in truncation. Thus the comparison needs to be
change from == to >.
These strings are compile time constants so this patch doesn't
affect runtime.
Fixes: ae380ce047 ("UBIFS: lessen the size of debugging info data structure")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
There is no reason to be limited to 4kiB page NAND chips just because
this is the maximum length the ELM is able to handle in one go. Just
call the ELM several times and it will process as many data as needed.
Here we introduce the concept of ECC page (which is at most 4kiB). The
ELM will be sought as many times as there are ECC pages.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ryan Barnett <ryan.barnett@collins.com>
Link: https://lore.kernel.org/linux-mtd/20210610134906.3503303-6-miquel.raynal@bootlin.com
The macro BADBLOCK_MARKER_LENGTH is pretty long and could be reduced to
BBM_LEN which is more handy to use in the code.
This is a purely cosmetic change and is only done to avoid further
change to contain 100+ char lines just because of this definition.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610134906.3503303-3-miquel.raynal@bootlin.com
This hardware controller is embedded in XilinX Zynq-7000 SoCs and has
partial support for Hamming ECC correction.
This work is inspired from the original contributions of Punnaiah
Choudary Kalluri and Naga Sureshkumar Relli.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Michael Walle <michael@walle.cc> [on zynq-7000]
Link: https://lore.kernel.org/linux-mtd/20210610082040.2075611-19-miquel.raynal@bootlin.com
After power up, all SPI NAND's blocks are locked. Only read operations
are allowed, write and erase operations are forbidden.
The SPI NAND framework unlocks all the blocks during its initialization.
During a standby low power, the memory is powered down, losing its
configuration.
During the resume, the QSPI driver state is restored but the SPI NAND
framework does not reconfigured the memory.
This patch adds SPI-NAND MTD PM handlers for resume ops.
SPI NAND resume op re-initializes SPI NAND flash to its probed state.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210602094913.26472-4-patrice.chotard@foss.st.com
There are 2 timing registers:
- "data interface"
- "timings"
So far, the "data interface" register was named "timings" which begins
misleading when bringing support for the "timings" register. Rename it
to "data_iface".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210527084959.208804-1-miquel.raynal@bootlin.com
Without the use of le16_to_cpu(), these accesses would have been wrong
on a big-endian machine.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 45606518f9 ("mtd: rawnand: Add onfi_fill_nvddr_interface_config() helper")
Fixes: 9310668fb6 ("mtd: rawnand: Retrieve NV-DDR timing modes from the ONFI parameter page")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210527084913.208635-1-miquel.raynal@bootlin.com
Xilinx ZynqMP SoC and the Arasan controller support 64-bit DMA
addressing. Define the right mask otherwise the default is 32
and some accesses may overflow the default mask.
Reported-by: Jorge Courett <jorge.courett@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jorge Courett <jorge.courett@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20210527084548.208429-1-miquel.raynal@bootlin.com
Information was redundant between struct pstore_zone_info and struct
pstore_device_info. Use struct pstore_zone_info, with member name "zone".
Additionally untangle the logic for the "best effort" block device
instance.
Signed-off-by: Kees Cook <keescook@chromium.org>
Fixed-by: Pu Lehui <pulehui@huawei.com>
Link: https://lore.kernel.org/lkml/20210617005424.182305-1-pulehui@huawei.com
Various places expect the request_queue in ->rq. Initialize it to
avoid NULL pointer derefences.
Fixes: 6966bb921d ("mtd_blkdevs: use blk_mq_alloc_disk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add support to show the manufacturer, the partname and JEDEC identifier
as well as to dump the SFDP table. Not all flashes list their SFDP table
contents in their datasheet. So having that is useful. It might also be
helpful in bug reports from users.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Due to possible mode switching to 8D-8D-8D, it might not be possible to
read the SFDP after the initial probe. To be able to dump the SFDP via
sysfs afterwards, make a complete copy of it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610022850.15397-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610022631.15344-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610022416.15291-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610022239.15238-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610022100.15185-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610021400.15132-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610021201.15076-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610020958.15023-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610020620.14970-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610020130.14917-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610015052.14864-1-thunder.leizhen@huawei.com
Compared with the definition of DEVICE_ATTR_RO/RW(), the read and write
function names of the sysfs attribute have an additional "mtd_" prefix.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210603125323.12142-2-thunder.leizhen@huawei.com
In the raw NAND world, ECC engines increment ecc_stats and the final
caller is responsible for returning -EBADMSG if the verification
failed.
In the SPI-NAND world it was a bit different until now because there was
only one possible ECC engine: the on-die one. Indeed, the
spinand_mtd_read() call was incrementing the ecc_stats counters
depending on the outcome of spinand_check_ecc_status() directly.
So now let's split the logic like this:
- spinand_check_ecc_status() is specific to the SPI-NAND on-die engine
and is kept very simple: it just returns the ECC status (bonus point:
the content of this helper can be overloaded).
- spinand_ondie_ecc_finish_io_req() is the caller of
spinand_check_ecc_status() and will increment the counters and
eventually return -EBADMSG.
- spinand_mtd_read() is not tied to the on-die ECC implementation and
should be able to handle results coming from other ECC engines: it has
the responsibility of returning the maximum number of bitflips which
happened during the entire operation as this is the only helper that
is aware that several pages may be read in a row.
Fixes: 945845b54c ("mtd: spinand: Instantiate a SPI-NAND on-die ECC engine")
Reported-by: YouChing Lin <ycllin@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: YouChing Lin <ycllin@mxic.com.tw>
Link: https://lore.kernel.org/linux-mtd/20210527084345.208215-1-miquel.raynal@bootlin.com
Use blk_mq_alloc_disk and blk_cleanup_disk to simplify the gendisk and
request_queue allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210602065345.355274-27-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use the blk_mq_alloc_disk API to simplify the gendisk and request_queue
allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Link: https://lore.kernel.org/r/20210602065345.355274-10-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Winbond flashes with OTP support provide a command to erase the OTP
data. This might come in handy during development.
This was tested with a Winbond W25Q32JW on a LS1028A SoC with the
NXP FSPI controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
SPI NOR flashes will just ignore program commands if the OTP region is
locked. Thus, a user might not notice that the intended write didn't end
up in the flash. Return -EROFS to the user in this case. From what I can
tell, chips/cfi_cmdset_0001.c also return this error code.
One could optimize spi_nor_mtd_otp_range_is_locked() to read the status
register only once and not for every OTP region, but for that we would
need some more invasive changes. Given that this is
one-time-programmable memory and the normal access mode is reading, we
just live with the small overhead.
By moving the code around a bit, we can just check the length before
calling spi_nor_mtd_otp_range_is_locked() and avoid an underflow there
if a len is 0. This way we don't need to take the lock either. We also
skip the "*retlen = 0" assignment, mtdcore already takes care of that
for us.
Fixes: 069089acf8 ("mtd: spi-nor: add OTP support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Use the wording as used in the datasheet to describe the access methods
of the security registers (aka OTP storage). This will also match the
function names.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The security registers either take a 3 byte or a 4 byte address offset,
depending on the address mode of the flash. Thus just leave the
nor->addr_width as is.
Fixes: cad3193fe9 ("mtd: spi-nor: implement OTP support for Winbond and similar flashes")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Make use of spi-mem poll status APIs to let advanced controllers
optimize wait operations.
This should also fix the high CPU usage for system that don't have
a dedicated STATUS poll block logic.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210518162754.15940-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Macronix MX25L12805D supports locking with 4 block
protection bits in its status register. Add the corresponding
flag in order to clear these bits when unloking the flash.
Otherwise, the flash might not be writable depending on the state
left by the bootloader.
Tested-on: Ubiquiti UniFi AC Lite (ath79)
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
According to macronix website, there is no mx66l51235l part number.
The chip detected as such is actually mx66l51235f. Rename the flash.
Do not update the mx66l51235l name from the spi_nor_dev_ids[], since
there are dt that are using this compatible.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Intel Alder Lake-M has the same SPI serial flash controller as Alder
Lake-S. Add Alder Lake-M PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Use the correct argument names in the kerneldoc.
Fixes: cad3193fe9 ("mtd: spi-nor: implement OTP support for Winbond and similar flashes")
Reported-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Document what the function does and that it should only be used when it
is known that the device supports it. This will avoid unaware
programmers thinking that they can arbitrarily use it to reset the
device.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Use SPI_MODE_X_MASK instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
The result of an expression consisting of a single relational operator is
already of the bool type and does not need to be evaluated explicitly.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210510114944.3527-1-thunder.leizhen@huawei.com
Make use of the cs-gpios DT property as well as the core helper to parse
it so that the Arasan controller driver can now assert many more chips
than natively.
The Arasan controller has an internal limitation: RB0 is tied to CS0 and
RB1 is tied to CS1. Hence, it is possible to use external GPIOs as long
as one or the other native CS is not used (or configured to be driven as
a GPIO) and that all additional CS are physically wired on its
corresponding RB line. Eg. CS0 is used as a native CS, CS1 is not used
as native CS and may be used as a GPIO CS, CS2 is an additional GPIO
CS. Then the target asserted by CS0 should also be wired to RB0, while
the targets asserted by CS1 and CS2 should be wired to RB1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-5-miquel.raynal@bootlin.com
The controller being always asserting one CS or the other, there is no
need to actually select the right target before doing a page read/write.
However, the anfc_select_target() helper actually also changes the
timing configuration and clock in the case were two different NAND chips
with different timing requirements would be used. In this situation, we
must ensure proper configuration of the controller by calling it.
As a consequence of this change, the anfc_select_target() helper is
being moved earlier in the driver.
Fixes: 88ffef1b65 ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-4-miquel.raynal@bootlin.com
New chips may feature a lot of CS because of their extended length. As
many controllers have been designed a decade ago, they usually only
feature just a couple. This does not mean that the entire range of
these chips cannot be accessed: it is just a matter of adding more
GPIO CS in the hardware design. A DT property has been added to
describe the CS array: cs-gpios.
Here is the code parsing it this new property, allocating what needs to
be, requesting the GPIOs and returning an array with the additional
available CS. The first entries of this array are left empty and are
reserved for native CS.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-3-miquel.raynal@bootlin.com
Add cleanup function as the name variable for the partition name was
allocaed but never freed after the use as the add mtd function
duplicate the name and free the pparts struct as the partition name is
assumed to be static.
The leak was found using kmemleak.
Fixes: 803eb124e1 ("mtd: parsers: Add Qcom SMEM parser")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210525230931.30013-1-ansuelsmth@gmail.com
fis-index-block is seeked in the master node and not in the partitions node.
For following binding and current usage, the driver need to check the
partitions subnode.
Fixes: c0e118c8a1 ("mtd: partitions: Add OF support to RedBoot partitions")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210520114851.1274609-1-clabbe@baylibre.com
As explained in the comment introduced above the fix, the Arasan
controller driver starts an operation when the prog register is being
written with a "type" specific to the action to perform.
The prog type used until now to perform a CHANGE READ COLUMN with an SDR
interface was the PAGE READ type (CMD + ADDR + CMD +
DATA). Unfortunately, for an unknown reason (let's call this a silicon
bug) any CHANGE READ COLUMN performed this way in NV-DDR mode will fail:
the data ready flag will never be triggered, nor will be the transfer
complete flag. Forcefully, this leads to a timeout situation which is
not easy to handle.
Fortunately, it was spotted that sending the same commands through a
different prog register "type", CHANGE READ COLUMN ENHANCED, would work
all the time (even though this particular command is not supported by
the core and is only available in a limited set of devices - we only
care about the controller configuration and not the actual command which
is sent to the device). So let's use this type instead when a CHANGE
READ COLUMN is requested.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-22-miquel.raynal@bootlin.com
Now that the necessary peaces to support the NV-DDR interface type have
been contributed, let's add the relevant logic to make use of it. In
particular, the core does not choose the best SDR timings anymore but
calls a more generic helper instead.
This helper checks if NV-DDR is supported by trying to find the best
NV-DDR supported mode through a logic very close to what is being done
for SDR timings. If no NV-DDR mode in common between the NAND controller
and the NAND chip is found, the core will fallback to SDR.
Side note: theoretically, the data clock speed in NV-DDR mode 0 is
slower than in SDR mode 5. In the situation where we would get a working
NV-DDR mode 0, we could also try if SDR mode 5 is supported and
eventually fallback to it in order to get the fastest possible
throughput. However, in the field, it looks like most of the devices
supporting NV-DDR avoid implementing the fastest SDR modes (like 4 and 5
EDO modes, which are a bit more complicated to handle than the other SDR
modes). So, we will stick to the simplest logic: try NV-DDR otherwise
fallback to SDR. If someone else experiences strong differences because
of that we may still implement the logic defined above.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-19-miquel.raynal@bootlin.com
Until now the parameter of the ADDR_TIMING_MODE feature was just the
ONFI timing mode (from 0 to 5) because we were only supporting the SDR
data interface. In the same byte, bits 4 and 5 indicate which data
interface is being configured so use them to set the right mode and also
read them back to ensure the right timing has been setup on the chip's
side.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-17-miquel.raynal@bootlin.com
Introduce a similar helper to onfi_find_closest_sdr_mode(), but for
NV-DDR timings. It just takes a timing structure as parameter and
returns the closest mode by comparing all minimum timings. This is
useful for rigid controllers on which tuning the timings is not
possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-16-miquel.raynal@bootlin.com
As explained in chapter "NV-DDR / NV-DDR2 / NV-DDR3 and Repeat Bytes" of
the ONFI specification, with some commands (mainly the commands which do
not transfer actual data) the data bytes are repeated twice and it is
the responsibility of the receiver to discard them properly. The
concerned commands are: SET_FEATURES, READ_ID, GET_FEATURES,
READ_STATUS, READ_STATUS_ENHANCED, ODT_CONFIGURE. Hence, in the NAND
core we are only impacted by the implementation of READ_ID, GET_FEATURES
and READ_STATUS.
The logic is the same for all:
2/ Check if it is relevant to read all data bytes twice.
1/ Allocate a buffer with twice the requested size (may be done
statically).
2/ Update the instruction structure to read these extra bytes in the
allocated buffer.
3/ Copy the even bytes into the original buffer. The performance hit is
negligible on such small data transfers anyway and we don't really
care about performances at this stage anyway.
4/ Free the allocated buffer, if any.
Note: nand_data_read_op() is also impacted because it is theoretically
possible to run the command/address cycles first, and, as another
operation, do the data transfers. In this case we can easily identify
the impacted commands because the force_8bit flag will be set (due to
the same reason: their data does not go through the same pipeline).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-15-miquel.raynal@bootlin.com
Most timings related to the bus timings are different between SDR and
NV-DDR. However, we identified 9 individual timings which are more
related to the NAND chip internals. These are common between the two
interface types. Fortunately, only these common timings are being shared
through the NAND core and its ->exec_op() interface, which allows the
writing of a simple macro checking the interface type and depending on
it, returning either the relevant SDR timing or the NV-DDR timing. This
is the purpose of the NAND_COMMON_TIMING_PS() macro.
As all this is evaluated at build time, one will immediately be notified
in case a non common timing is being accessed through this macro.
Two handy macros are also inserted at the same time, which use
PSEC_TO_NSEC or PSEC_TO_MSEC so that it is very easy to return timings
in milli-, nano- or pico-seconds, as usually requested by the internal
API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-14-miquel.raynal@bootlin.com
Pratyush Yadav
Tudor Ambarus
Flavio Suligoi
Lad Prabhakar
Roger Quadros
Miquel Raynal
Arnd Bergmann
Minghao Chi
Dmitry Osipenko
Christoph Hellwig
Michał Kępień
Christophe JAILLET
Colin Ian King
Geert Uytterhoeven
Jon Hunter
Herve Codina
Cai Huoqing
Zev Weiss
Uwe Kleine-König
Michael Walle
Andreas Oetken
George G. Davis
Christian Eggers
Stefan Riedmueller
Paul Cercueil
Linus Torvalds
Luis Chamberlain
Joachim Wiberg
Chris Morgan
Evgeny Novikov
Jonathan Lemon
Krzysztof Kozlowski
Colin Ian King
Md Sadre Alam
Daniel Lezcano
Zhihao Cheng
Lukas Bulwahn
Sean Young
Ezequiel Garcia
Jaime Liao
Jason Wang
Vladimir Molokov
Daniel Palmer
Manivannan Sadhasivam
Desmond Cheong Zhi Xi
Andreas Persson
Dan Carpenter
Gustavo A. R. Silva
Richard Weinberger
Mark Brown
Souptick Joarder
Zhen Lei
Patrice Chotard
Yang Yingliang
Kees Cook
Zou Wei
Heiko Schocher
David Bauer
Mika Westerberg
Andy Shevchenko
Ansuel Smith
Corentin Labbe
Ding Senjie