commit 0e32818397 upstream.
When pci_assign_resource() is unable to assign resources to a BAR, it uses
pci_revert_fw_address() to fall back to a firmware assignment (if any).
Previously pci_revert_fw_address() assumed all addresses could reach the
device, but this is not true if the device is below a bridge that only
forwards addresses within its windows.
This problem was observed on a Tyan Tomcat IV S1564D system where the BIOS
did not assign valid addresses to several bridges and USB devices:
pci 0000:00:11.0: PCI-to-PCIe bridge to [bus 01-ff]
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: PCIe Upstream Port to [bus 02-ff]
pci 0000:01:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:02:02.0: PCIe Downstream Port to [bus 05-ff]
pci 0000:02:02.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:05:00.0: PCIe-to-PCI bridge to [bus 06-ff]
pci 0000:05:00.0: bridge window [io 0x0000-0x0fff] # unreachable
pci 0000:06:08.0: USB UHCI 1.1
pci 0000:06:08.0: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.1: USB UHCI 1.1
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] # unreachable
pci 0000:06:08.0: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
pci 0000:06:08.1: can't claim BAR 4 [io 0xfce0-0xfcff]: no compatible bridge window
During the first pass of assigning unassigned resources, there was not
enough I/O space available, so we couldn't assign the 06:08.0 BAR and
reverted to the firmware assignment (still unreachable). Reverting the
06:08.1 assignment failed because it conflicted with 06:08.0:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff]
pci 0000:01:00.0: no space for bridge window [io size 0x2000]
pci 0000:02:02.0: no space for bridge window [io size 0x1000]
pci 0000:05:00.0: no space for bridge window [io size 0x1000]
pci 0000:06:08.0: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.0: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: no space for [io size 0x0020]
pci 0000:06:08.1: BAR 4: trying firmware assignment [io 0xfce0-0xfcff]
pci 0000:06:08.1: BAR 4: [io 0xfce0-0xfcff] conflicts with 0000:06:08.0 [io 0xfce0-0xfcff]
A subsequent pass assigned valid bridge windows and a valid 06:08.1 BAR,
but left the 06:08.0 BAR alone, so the UHCI device was still unusable:
pci 0000:00:11.0: bridge window [io 0xe000-0xefff] released
pci 0000:00:11.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:01:00.0: bridge window [io 0x1000-0x2fff] # reassigned
pci 0000:02:02.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:05:00.0: bridge window [io 0x2000-0x2fff] # reassigned
pci 0000:06:08.0: BAR 4: assigned [io 0xfce0-0xfcff] # left alone
pci 0000:06:08.1: BAR 4: assigned [io 0x2000-0x201f]
...
uhci_hcd 0000:06:08.0: host system error, PCI problems?
uhci_hcd 0000:06:08.0: host controller process error, something bad happened!
uhci_hcd 0000:06:08.0: host controller halted, very bad!
uhci_hcd 0000:06:08.0: HCRESET not completed yet!
uhci_hcd 0000:06:08.0: HC died; cleaning up
If the address assigned by firmware is not reachable because it's not
within upstream bridge windows, fail instead of assigning the unusable
address from firmware.
[bhelgaas: commit log, use pci_upstream_bridge()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=16263
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2203012338460.46819@angie.orcam.me.uk
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209211921250.29493@angie.orcam.me.uk
Fixes: 58c84eda07 ("PCI: fall back to original BIOS BAR addresses")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.35+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c968af565c which is
commit 8795e182b0 upstream.
It is reported to cause problems, so drop it from the stable trees for
now until it gets sorted out.
Link: https://lore.kernel.org/r/47b775c5-57fa-5edf-b59e-8a9041ffbee7@candelatech.com
Reported-by: Ben Greear <greearb@candelatech.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pali Rohár <pali@kernel.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yao Hongbo <yaohongbo@linux.alibaba.com>
Cc: Naveen Naidu <naveennaidu479@gmail.com>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bcdb6fd4f3 ]
Slot capabilities are currently not reported because emulated bridge does
not report the PCI_EXP_FLAGS_SLOT flag.
Set PCI_EXP_FLAGS_SLOT to let the kernel know that PCI_EXP_SLT* registers
are supported.
Move setting of PCI_EXP_SLTCTL register from "dynamic" pcie_conf_read
function to static buffer as it is only statically filled the
PCI_EXP_SLTSTA_PDS flag and dynamic read callback is not needed for this
register.
Set Presence State Bit to 1 since there is no support for unplugging the
card and there is currently no platform able to detect presence of a card -
in such a case the bit needs to be set to 1.
Finally correctly set Physical Slot Number to 1 since there is only one
port and zero value is reserved for ports within the same silicon as Root
Port which is not our case for Aardvark HW.
Link: https://lore.kernel.org/r/20220524132827.8837-3-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afd306a65c ]
The Broadcom BCM5750x NICs may be multi-function devices. They do not
advertise ACS capability. Peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.
Add an ACS quirk for these devices so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.
Link: https://lore.kernel.org/r/1654796507-28610-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0e43bb997 ]
Currently the Gen2 port in IPQ8074 will cause the system to hang as it
accesses DBI registers in qcom_pcie_init_2_3_3(), and those are only
accesible after phy_power_on().
Move the DBI read/writes to a new qcom_pcie_post_init_2_3_3(), which is
executed after phy_power_on().
Link: https://lore.kernel.org/r/20220623155004.688090-1-robimarko@gmail.com
Fixes: a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: stable@vger.kernel.org # v5.11+
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e6ae05095 ]
Previously we iterated over AER stat *names*, e.g.,
aer_correctable_error_string[32], but the actual stat *counters* may not be
that large, e.g., pdev->aer_stats->dev_cor_errs[16], which means that we
printed junk in the sysfs stats files.
Iterate over the stat counter arrays instead of the names to avoid this
junk.
Also, added a build time check to make sure all
counters have entries in strings array.
Fixes: 0678e3109a ("PCI/AER: Simplify __aer_print_error()")
Link: https://lore.kernel.org/r/20220509181441.31884-1-mkhalfella@purestorage.com
Reported-by: Meeta Saggi <msaggi@purestorage.com>
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Meeta Saggi <msaggi@purestorage.com>
Reviewed-by: Eric Badger <ebadger@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6646e99bce ]
As part of Root Port interrupt handling, level-0 register is read first and
based on the bits set in that, corresponding level-1 registers are read for
further interrupt processing. Since both these values are currently read
into the same 'val' variable, checking level-0 bits the second time around
is happening on the 'val' variable value of level-1 register contents
instead of freshly reading the level-0 value again.
Fix by using different variables to store level-0 and level-1 registers
contents.
Link: https://lore.kernel.org/r/20220721142052.25971-11-vidyas@nvidia.com
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38f897ae3d ]
We currently enable clocks BEFORE we write to PARF_PHY_CTRL reg to enable
clocks and resets. This causes the driver to never set to a ready state
with the error 'Phy link never came up'.
This is caused by the PHY clock getting enabled before setting the required
bits in the PARF regs.
A workaround for this was set but with this new discovery we can drop
the workaround and use a proper solution to the problem by just enabling
the clock only AFTER the PARF_PHY_CTRL bit is set.
This correctly sets up the PCIe link and makes it usable even when a
bootloader leaves the PCIe link in an undefined state.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Link: https://lore.kernel.org/r/20220708222743.27019-1-ansuelsmth@gmail.com
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8795e182b0 ]
AER reporting is currently disabled in the DevCtl registers of all non Root
Port PCIe devices on systems using pcie_ports_native || host->native_aer,
disabling AER completely in such systems. This is because 2bd50dd800
("PCI: PCIe: Disable PCIe port services during port initialization"), added
a call to pci_disable_pcie_error_reporting() *after* the AER setup was
completed for the PCIe device tree.
Here a longer analysis about the current status of AER enabling /
disabling upon bootup provided by Bjorn:
pcie_portdrv_probe
pcie_port_device_register
get_port_device_capability
pci_disable_pcie_error_reporting
clear CERE NFERE FERE URRE # <-- disable for RP USP DSP
pcie_device_init
device_register # new AER service device
aer_probe
aer_enable_rootport # RP only
set_downstream_devices_error_reporting
set_device_error_reporting # self (RP)
if (RP || USP || DSP)
pci_enable_pcie_error_reporting
set CERE NFERE FERE URRE # <-- enable for RP
pci_walk_bus
set_device_error_reporting
if (RP || USP || DSP)
pci_enable_pcie_error_reporting
set CERE NFERE FERE URRE # <-- enable for USP DSP
In a typical Root Port -> Endpoint hierarchy, the above:
- Disables Error Reporting for the Root Port,
- Enables Error Reporting for the Root Port,
- Does NOT enable Error Reporting for the Endpoint because it is not a
Root Port or Switch Port.
In a deeper Root Port -> Upstream Switch Port -> Downstream Switch
Port -> Endpoint hierarchy:
- Disables Error Reporting for the Root Port,
- Enables Error Reporting for the Root Port,
- Enables Error Reporting for both Switch Ports,
- Does NOT enable Error Reporting for the Endpoint because it is not a
Root Port or Switch Port,
- Disables Error Reporting for the Switch Ports when pcie_portdrv_probe()
claims them. AER does not re-enable it because these are not Root
Ports.
Remove this call to pci_disable_pcie_error_reporting() from
get_port_device_capability(), leaving the already enabled AER configuration
intact. With this change, AER is enabled in the Root Port and the PCIe
switch upstream and downstream ports. Only the PCIe Endpoints don't have
AER enabled yet. A follow-up patch will take care of this Endpoint
enabling.
Fixes: 2bd50dd800 ("PCI: PCIe: Disable PCIe port services during port initialization")
Link: https://lore.kernel.org/r/20220125071820.2247260-3-sr@denx.de
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yao Hongbo <yaohongbo@linux.alibaba.com>
Cc: Naveen Naidu <naveennaidu479@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bc2b7bfba ]
Unbinding an endpoint function from the endpoint controller shouldn't stop
the controller. This is especially a problem for multi-function endpoints
where other endpoints may still be active.
Don't stop the controller when unbinding one of its endpoints. Normally
the controller is stopped via configfs.
Fixes: 349e7a85b2 ("PCI: endpoint: functions: Add an EP function to test PCI")
Link: https://lore.kernel.org/r/20220622040924.113279-1-mie@igel.co.jp
Signed-off-by: Shunsuke Mie <mie@igel.co.jp>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec7b952f45 ]
If the "snps,enable-cdm-check" property exists, we should enable the CDM
check. But previously dw_pcie_setup() could exit before doing so if the
"num-lanes" property was absent or invalid.
Move the CDM enable earlier so we do it regardless of whether "num-lanes"
is present.
[bhelgaas: commit log]
Fixes: 07f123def7 ("PCI: dwc: Add support to enable CDM register check")
Link: https://lore.kernel.org/r/20220624143428.8334-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8161e9626b ]
If dw_pcie_ep_init() fails to perform any action after the EPC memory is
initialized and the MSI memory region is allocated, the latter parts won't
be undone thus causing a memory leak. Add a cleanup-on-error path to fix
these leaks.
[bhelgaas: commit log]
Fixes: 2fd0c9d966 ("PCI: designware-ep: Pre-allocate memory for MSI in dw_pcie_ep_init")
Link: https://lore.kernel.org/r/20220624143428.8334-6-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 777e7c3ab7 ]
We program the 64-bit ATU limit address (in PCIE_ATU_LIMIT/
PCIE_ATU_UPPER_LIMIT or PCIE_ATU_UNR_LOWER_LIMIT/PCIE_ATU_UNR_UPPER_LIMIT),
but in addition, the PCIE_ATU_INCREASE_REGION_SIZE bit must be set if the
upper 32 bits of the limit address differ from the upper 32 bits of the
base address (see [1,2]).
5b4cf0f653 ("PCI: dwc: Add upper limit address for outbound iATU") set
PCIE_ATU_INCREASE_REGION_SIZE, but only when the *size* was greater than
4GB. It did not set it when a smaller region crossed a 4GB boundary, e.g.,
[mem 0x0_f0000000-0x1_0fffffff].
Set PCIE_ATU_INCREASE_REGION_SIZE whenever PCIE_ATU_UPPER_LIMIT is
greater than PCIE_ATU_UPPER_BASE.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-36, p.175
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-37, p.176
[bhelgaas: commit log]
Fixes: 5b4cf0f653 ("PCI: dwc: Add upper limit address for outbound iATU")
Link: https://lore.kernel.org/r/20220624143428.8334-5-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d60a2e281e ]
Some DWC-based controllers (e.g., pcie-al.c and pci-keystone.c, identified
by the fact that they override the default dw_child_pcie_ops) use their own
address translation approach instead of the DWC internal ATU (iATU). For
those controllers, skip disabling the iATU outbound windows.
[bhelgaas: commit log, update multiple window comment]
Fixes: 458ad06c4c ("PCI: dwc: Ensure all outbound ATU windows are reset")
Link: https://lore.kernel.org/r/20220624143428.8334-4-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1cf738f2b ]
dw_pcie_disable_atu() was introduced by f8aed6ec62 ("PCI: dwc:
designware: Add EP mode support") and supported only the viewport version
of the iATU CSRs.
DW PCIe IP cores v4.80a and newer also support unrolled iATU/eDMA space.
Callers of dw_pcie_disable_atu(), including pci_epc_ops.clear_bar(),
pci_epc_ops.unmap_addr(), and dw_pcie_setup_rc(), don't work correctly when
it is enabled.
Add dw_pcie_disable_atu() support for controllers with unrolled iATU CSRs
enabled.
[bhelgaas: commit log]
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20220624143428.8334-3-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 113fa857b7 ]
It's logically correct to undo everything that was done when an error is
discovered or in the corresponding cleanup counterpart. Otherwise the host
controller will be left in an undetermined state. Since the link is set up
in the host_init method, deactivate it there in the cleanup-on-error block
and stop the link in the antagonistic routine - dw_pcie_host_deinit(). Link
deactivation is platform-specific and should be implemented in
dw_pcie_ops.stop_link().
Fixes: 886a9c1347 ("PCI: dwc: Move link handling into common code")
Link: https://lore.kernel.org/r/20220624143428.8334-2-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b80892ca02 ]
No driver is left using the external pgmap refcount, so remove the
code to support it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211028151017.50234-1-hch@lst.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf038503d5 ]
of_get_child_by_name() returns a node pointer with refcount incremented, so
we should use of_node_put() on it when we don't need it anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 814cceebba ("PCI: mediatek-gen3: Add INTx support")
Link: https://lore.kernel.org/r/20220601041259.56185-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e8fbd344a5 ]
pm_runtime_enable() will increase power disable depth. If
dw_pcie_ep_init() fails, we should use pm_runtime_disable() to balance it
with pm_runtime_enable().
Add missing pm_runtime_disable() for tegra_pcie_config_ep().
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/r/20220602031910.55859-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f030304fde ]
of_get_next_child() returns a node pointer with refcount incremented, so we
should use of_node_put() on it when we don't need it anymore.
mc_pcie_init_irq_domains() only calls of_node_put() in the normal path,
missing it in some error paths. Add missing of_node_put() to avoid
refcount leak.
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Link: https://lore.kernel.org/r/20220605055123.59127-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a2bad844a6 upstream.
According to Dexuan, the hypervisor folks beleive that multi-msi
allocations are not correct. compose_msi_msg() will allocate multi-msi
one by one. However, multi-msi is a block of related MSIs, with alignment
requirements. In order for the hypervisor to allocate properly aligned
and consecutive entries in the IOMMU Interrupt Remapping Table, there
should be a single mapping request that requests all of the multi-msi
vectors in one shot.
Dexuan suggests detecting the multi-msi case and composing a single
request related to the first MSI. Then for the other MSIs in the same
block, use the cached information. This appears to be viable, so do it.
5.15 backport - add hv_msi_get_int_vector helper function. Fixed merge
conflict due to delivery_mode name change (APIC_DELIVERY_MODE_FIXED
is the value given to DELIVERY_MODE on x86). Removed unused variable
in hv_compose_msi_msg. Fixed reference to msi_desc->pci to point to
the same is_msix variable.
Suggested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1652282599-21643-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4b77778ec upstream.
Currently if compose_msi_msg() is called multiple times, it will free any
previous IRTE allocation, and generate a new allocation. While nothing
prevents this from occurring, it is extraneous when Linux could just reuse
the existing allocation and avoid a bunch of overhead.
However, when future IRTE allocations operate on blocks of MSIs instead of
a single line, freeing the allocation will impact all of the lines. This
could cause an issue where an allocation of N MSIs occurs, then some of
the lines are retargeted, and finally the allocation is freed/reallocated.
The freeing of the allocation removes all of the configuration for the
entire block, which requires all the lines to be retargeted, which might
not happen since some lines might already be unmasked/active.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1652282582-21595-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 455880dfe2 upstream.
In the multi-MSI case, hv_arch_irq_unmask() will only operate on the first
MSI of the N allocated. This is because only the first msi_desc is cached
and it is shared by all the MSIs of the multi-MSI block. This means that
hv_arch_irq_unmask() gets the correct address, but the wrong data (always
0).
This can break MSIs.
Lets assume MSI0 is vector 34 on CPU0, and MSI1 is vector 33 on CPU0.
hv_arch_irq_unmask() is called on MSI0. It uses a hypercall to configure
the MSI address and data (0) to vector 34 of CPU0. This is correct. Then
hv_arch_irq_unmask is called on MSI1. It uses another hypercall to
configure the MSI address and data (0) to vector 33 of CPU0. This is
wrong, and results in both MSI0 and MSI1 being routed to vector 33. Linux
will observe extra instances of MSI1 and no instances of MSI0 despite the
endpoint device behaving correctly.
For the multi-MSI case, we need unique address and data info for each MSI,
but the cached msi_desc does not provide that. However, that information
can be gotten from the int_desc cached in the chip_data by
compose_msi_msg(). Fix the multi-MSI case to use that cached information
instead. Since hv_set_msi_entry_from_desc() is no longer applicable,
remove it.
5.15 backport - no changes to code, but merge conflict due to refactor.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1651068453-29588-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08e61e861a upstream.
If the allocation of multiple MSI vectors for multi-MSI fails in the core
PCI framework, the framework will retry the allocation as a single MSI
vector, assuming that meets the min_vecs specified by the requesting
driver.
Hyper-V advertises that multi-MSI is supported, but reuses the VECTOR
domain to implement that for x86. The VECTOR domain does not support
multi-MSI, so the alloc will always fail and fallback to a single MSI
allocation.
In short, Hyper-V advertises a capability it does not implement.
Hyper-V can support multi-MSI because it coordinates with the hypervisor
to map the MSIs in the IOMMU's interrupt remapper, which is something the
VECTOR domain does not have. Therefore the fix is simple - copy what the
x86 IOMMU drivers (AMD/Intel-IR) do by removing
X86_IRQ_ALLOC_CONTIGUOUS_VECTORS after calling the VECTOR domain's
pci_msi_prepare().
5.15 backport - adds the hv_msi_prepare wrapper function
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/1649856981-14649-1-git-send-email-quic_jhugo@quicinc.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Carl Vanderlip <quic_carlv@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea401499e9 ]
Stuart Hayes reports that an error handled by DPC at a Root Port results
in pciehp gratuitously bringing down a subordinate hotplug port:
RP -- UP -- DP -- UP -- DP (hotplug) -- EP
pciehp brings the slot down because the Link to the Endpoint goes down.
That is caused by a Hot Reset being propagated as a result of DPC.
Per PCIe Base Spec 5.0, section 6.6.1 "Conventional Reset":
For a Switch, the following must cause a hot reset to be sent on all
Downstream Ports: [...]
* The Data Link Layer of the Upstream Port reporting DL_Down status.
In Switches that support Link speeds greater than 5.0 GT/s, the
Upstream Port must direct the LTSSM of each Downstream Port to the
Hot Reset state, but not hold the LTSSMs in that state. This permits
each Downstream Port to begin Link training immediately after its
hot reset completes. This behavior is recommended for all Switches.
* Receiving a hot reset on the Upstream Port.
Once DPC recovers, pcie_do_recovery() walks down the hierarchy and
invokes pcie_portdrv_slot_reset() to restore each port's config space.
At that point, a hotplug interrupt is signaled per PCIe Base Spec r5.0,
section 6.7.3.4 "Software Notification of Hot-Plug Events":
If the Port is enabled for edge-triggered interrupt signaling using
MSI or MSI-X, an interrupt message must be sent every time the logical
AND of the following conditions transitions from FALSE to TRUE: [...]
* The Hot-Plug Interrupt Enable bit in the Slot Control register is
set to 1b.
* At least one hot-plug event status bit in the Slot Status register
and its associated enable bit in the Slot Control register are both
set to 1b.
Prevent pciehp from gratuitously bringing down the slot by clearing the
error-induced Data Link Layer State Changed event before restoring
config space. Afterwards, check whether the link has unexpectedly
failed to retrain and synthesize a DLLSC event if so.
Allow each pcie_port_service_driver (one of them being pciehp) to define
a slot_reset callback and re-use the existing pm_iter() function to
iterate over the callbacks.
Thereby, the Endpoint driver remains bound throughout error recovery and
may restore the device to working state.
Surprise removal during error recovery is detected through a Presence
Detect Changed event. The hotplug port is expected to not signal that
event as a result of a Hot Reset.
The issue isn't DPC-specific, it also occurs when an error is handled by
AER through aer_root_reset(). So while the issue was noticed only now,
it's been around since 2006 when AER support was first introduced.
[bhelgaas: drop PCI_ERROR_RECOVERY Kconfig, split pm_iter() rename to
preparatory patch]
Link: https://lore.kernel.org/linux-pci/08c046b0-c9f2-3489-eeef-7e7aca435bb9@gmail.com/
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Link: https://lore.kernel.org/r/251f4edcc04c14f873ff1c967bc686169cd07d2d.1627638184.git.lukas@wunner.de
Reported-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.19+: ba952824e6c1: PCI/portdrv: Report reset for frozen channel
Cc: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fdf6a2f533 upstream.
Fix a clock imbalance introduced by ed8cc3b1fc ("PCI: qcom: Add support
for SDM845 PCIe controller"), which enables the pipe clock both in init()
and in post_init() but only disables in post_deinit().
Note that the pipe clock was also never disabled in the init() error
paths and that enabling the clock before powering up the PHY looks
questionable.
Link: https://lore.kernel.org/r/20220401133351.10113-1-johan+linaro@kernel.org
Fixes: ed8cc3b1fc ("PCI: qcom: Add support for SDM845 PCIe controller")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87d83b96c8 upstream.
Drop the leftover pm_runtime_disable() calls from the late probe error
paths that would, for example, prevent runtime PM from being reenabled
after a probe deferral.
Link: https://lore.kernel.org/r/20220401133854.10421-2-johan+linaro@kernel.org
Fixes: 6e5da6f7d8 ("PCI: qcom: Fix error handling in runtime PM support")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.20
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12068bb346 upstream.
92597f97a4 ("PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold") omitted
braces around the new Elo i2 entry, so it overwrote the existing Gigabyte
X299 entry. Add the appropriate braces.
Found by:
$ make W=1 drivers/pci/pci.o
CC drivers/pci/pci.o
drivers/pci/pci.c:2974:12: error: initialized field overwritten [-Werror=override-init]
2974 | .ident = "Elo i2",
| ^~~~~~~~
Link: https://lore.kernel.org/r/20220526221258.GA409855@bhelgaas
Fixes: 92597f97a4 ("PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7013654af6 ]
Clear the MSI bit in ISTATUS_LOCAL register after reading it, but
before reading and handling individual MSI bits from the ISTATUS_MSI
register. This avoids a potential race where new MSI bits may be set
on the ISTATUS_MSI register after it was read and be missed when the
MSI bit in the ISTATUS_LOCAL register is cleared.
ISTATUS_LOCAL is a read/write/clear register; the register's bits
are set when the corresponding interrupt source is activated. Each
source is independent and thus multiple sources may be active
simultaneously. The processor can monitor and clear status
bits. If one or more ISTATUS_LOCAL interrupt sources are active,
the RootPort issues an interrupt towards the processor (on
the AXI domain). Bit 28 of this register reports an MSI has been
received by the RootPort.
ISTATUS_MSI is a read/write/clear register. Bits 31-0 are asserted
when an MSI with message number 31-0 is received by the RootPort.
The processor must monitor and clear these bits.
Effectively, Bit 28 of ISTATUS_LOCAL informs the processor that
an MSI has arrived at the RootPort and ISTATUS_MSI informs the
processor which MSI (in the range 0 - 31) needs handling.
Reported by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/linux-pci/20220127202000.GA126335@bhelgaas/
Link: https://lore.kernel.org/r/20220517141622.145581-1-daire.mcnamara@microchip.com
Fixes: 6f15a9c9f9 ("PCI: microchip: Add Microchip PolarFire PCIe controller driver")
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 203926da2b ]
When a Root Port or Root Complex Event Collector receives an error Message
e.g., ERR_COR, it sets PCI_ERR_ROOT_COR_RCV in the Root Error Status
register and logs the Requester ID in the Error Source Identification
register. If it receives a second ERR_COR Message before software clears
PCI_ERR_ROOT_COR_RCV, hardware sets PCI_ERR_ROOT_MULTI_COR_RCV and the
Requester ID is lost.
In the following scenario, PCI_ERR_ROOT_MULTI_COR_RCV was never cleared:
- hardware receives ERR_COR message
- hardware sets PCI_ERR_ROOT_COR_RCV
- aer_irq() entered
- aer_irq(): status = pci_read_config_dword(PCI_ERR_ROOT_STATUS)
- aer_irq(): now status == PCI_ERR_ROOT_COR_RCV
- hardware receives second ERR_COR message
- hardware sets PCI_ERR_ROOT_MULTI_COR_RCV
- aer_irq(): pci_write_config_dword(PCI_ERR_ROOT_STATUS, status)
- PCI_ERR_ROOT_COR_RCV is cleared; PCI_ERR_ROOT_MULTI_COR_RCV is set
- aer_irq() entered again
- aer_irq(): status = pci_read_config_dword(PCI_ERR_ROOT_STATUS)
- aer_irq(): now status == PCI_ERR_ROOT_MULTI_COR_RCV
- aer_irq() exits because PCI_ERR_ROOT_COR_RCV not set
- PCI_ERR_ROOT_MULTI_COR_RCV is still set
The same problem occurred with ERR_NONFATAL/ERR_FATAL Messages and
PCI_ERR_ROOT_UNCOR_RCV and PCI_ERR_ROOT_MULTI_UNCOR_RCV.
Fix the problem by queueing an AER event and clearing the Root Error Status
bits when any of these bits are set:
PCI_ERR_ROOT_COR_RCV
PCI_ERR_ROOT_UNCOR_RCV
PCI_ERR_ROOT_MULTI_COR_RCV
PCI_ERR_ROOT_MULTI_UNCOR_RCV
See the bugzilla link for details from Eric about how to reproduce this
problem.
[bhelgaas: commit log, move repro details to bugzilla]
Fixes: e167bfcaa4 ("PCI: aerdrv: remove magical ROOT_ERR_STATUS_MASKS")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215992
Link: https://lore.kernel.org/r/20220418150237.1021519-1-sathyanarayanan.kuppuswamy@linux.intel.com
Reported-by: Eric Badger <ebadger@purestorage.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6809941c1 ]
According to the PCIe standard the PERST# signal (reset-gpio in
fsl,imx* compatible dts) should be kept asserted for at least 100 usec
before the PCIe refclock is stable, should be kept asserted for at
least 100 msec after the power rails are stable and the host should wait
at least 100 msec after it is de-asserted before accessing the
configuration space of any attached device.
From PCIe CEM r2.0, sec 2.6.2
T-PVPERL: Power stable to PERST# inactive - 100 msec
T-PERST-CLK: REFCLK stable before PERST# inactive - 100 usec.
From PCIe r5.0, sec 6.6.1
With a Downstream Port that does not support Link speeds greater than
5.0 GT/s, software must wait a minimum of 100 ms before sending a
Configuration Request to the device immediately below that Port.
Failure to do so could prevent PCIe devices to be working correctly,
and this was experienced with real devices.
Move reset assert to imx6_pcie_assert_core_reset(), this way we ensure
that PERST# is asserted before enabling any clock, move de-assert to the
end of imx6_pcie_deassert_core_reset() after the clock is enabled and
deemed stable and add a new delay of 100 msec just afterward.
Link: https://lore.kernel.org/all/20220211152550.286821-1-francesco.dolcini@toradex.com
Link: https://lore.kernel.org/r/20220404081509.94356-1-francesco.dolcini@toradex.com
Fixes: bb38919ec5 ("PCI: imx6: Add support for i.MX6 PCIe controller")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88557685cd ]
When dma_mapping_error() returns error because of no enough memory,
but dw_pcie_host_init() returns success, which will mislead the callers.
Link: https://lore.kernel.org/r/30170911-0e2f-98ce-9266-70465b9073e5@huawei.com
Fixes: 07940c369a ("PCI: dwc: Fix MSI page leakage in suspend/resume")
Signed-off-by: Jianrong Zhang <zhangjianrong5@huawei.com>
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 214e0d8fe4 ]
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Link: https://lore.kernel.org/r/20220309091953.5630-1-linmq006@gmail.com
Fixes: 87e8657ba9 ("PCI: mediatek: Add new method to get shared pcie-cfg base address")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Miles Chen <miles.chen@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 096950e230 ]
The ep->ob_region_map bitmap is a long and it has BITS_PER_LONG bits.
Link: https://lore.kernel.org/r/20220315065944.GB13572@kili
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0aa3a0937f ]
The ep->ob_region_map bitmap is a long and it has BITS_PER_LONG bits.
Link: https://lore.kernel.org/r/20220315065829.GA13572@kili
Fixes: 37dddf14f1 ("PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dff6139015 ]
acpi_pci_bridge_d3(dev) returns "true" if "dev" is a hotplug bridge that
can handle hotplug events while in D3. Previously this meant either:
- "dev" has a _PS0 or _PR0 method (acpi_pci_power_manageable()), or
- The Root Port above "dev" has a _DSD with a "HotPlugSupportInD3"
property with value 1.
This did not consider _PRW, which tells us about wakeup GPEs (ACPI v6.4,
sec 7.3.13). Without a wakeup GPE, from an ACPI perspective the Root Port
has no way of generating wakeup signals, so hotplug events will be lost if
we use D3.
Similarly, it did not consider _S0W, which tells us the deepest D-state
from which a device can wake itself (sec 7.3.20). If _S0W tells us the
device cannot wake from D3, hotplug events will again be lost if we use D3.
Some platforms, e.g., AMD Yellow Carp, supply "HotPlugSupportInD3" without
_PRW or with an _S0W that says the Root Port cannot wake from D3. On those
platforms, we previously put bridges in D3hot, hotplug events were lost,
and hotplugged devices would not be recognized without manually rescanning.
Allow bridges to be put in D3 only if the Root Port can generate wakeup
GPEs (wakeup.flags.valid), it can wake from D3 (_S0W), AND it has the
"HotPlugSupportInD3" property.
Neither Windows 10 nor Windows 11 puts the bridge in D3 when the firmware
is configured this way, and this change aligns the handling of the
situation to be the same.
[bhelgaas: commit log, tidy "HotPlugSupportInD3" check and comment]
Link: https://uefi.org/htmlspecs/ACPI_Spec_6_4_html/07_Power_and_Performance_Mgmt/device-power-management-objects.html?highlight=s0w#s0w-s0-device-wake-state
Link: https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#identifying-pcie-root-ports-supporting-hot-plug-in-d3
Link: https://lore.kernel.org/r/20220401034003.3166-1-mario.limonciello@amd.com
Fixes: 26ad34d510 ("PCI / ACPI: Whitelist D3 for more PCIe hotplug ports")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a91ee0e9fc ]
The sysfs sriov_numvfs_store() path acquires the device lock before the
config space access lock:
sriov_numvfs_store
device_lock # A (1) acquire device lock
sriov_configure
vfio_pci_sriov_configure # (for example)
vfio_pci_core_sriov_configure
pci_disable_sriov
sriov_disable
pci_cfg_access_lock
pci_wait_cfg # B (4) wait for dev->block_cfg_access == 0
Previously, pci_dev_lock() acquired the config space access lock before the
device lock:
pci_dev_lock
pci_cfg_access_lock
dev->block_cfg_access = 1 # B (2) set dev->block_cfg_access = 1
device_lock # A (3) wait for device lock
Any path that uses pci_dev_lock(), e.g., pci_reset_function(), may
deadlock with sriov_numvfs_store() if the operations occur in the sequence
(1) (2) (3) (4).
Avoid the deadlock by reversing the order in pci_dev_lock() so it acquires
the device lock before the config space access lock, the same as the
sriov_numvfs_store() path.
[bhelgaas: combined and adapted commit log from Jay Zhou's independent
subsequent posting:
https://lore.kernel.org/r/20220404062539.1710-1-jianjay.zhou@huawei.com]
Link: https://lore.kernel.org/linux-pci/1583489997-17156-1-git-send-email-yangyicong@hisilicon.com/
Also-posted-by: Jay Zhou <jianjay.zhou@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a3b69dd0ad ]
This reverts commit 1571d67dc1.
This commit broke support for setting interrupt affinity. It looks like
that it is related to the chained IRQ handler. Revert this commit until
issue with setting interrupt affinity is fixed.
Fixes: 1571d67dc1 ("PCI: aardvark: Rewrite IRQ code to chained IRQ handler")
Link: https://lore.kernel.org/r/20220515125815.30157-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 92597f97a4 upstream.
If a Root Port on Elo i2 is put into D3cold and then back into D0, the
downstream device becomes permanently inaccessible, so add a bridge D3 DMI
quirk for that system.
This was exposed by 14858dcc3b ("PCI: Use pci_update_current_state() in
pci_enable_device_flags()"), but before that commit the Root Port in
question had never been put into D3cold for real due to a mismatch between
its power state retrieved from the PCI_PM_CTRL register (which was
accessible even though the platform firmware indicated that the port was in
D3cold) and the state of an ACPI power resource involved in its power
management.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215715
Link: https://lore.kernel.org/r/11980172.O9o76ZdvQC@kreacher
Reported-by: Stefan Gottwald <gottwald@igel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92f4ffecc4 upstream.
Update the comment about what happens when link goes down after we have
checked for link-up. If a PIO request is done while link-down, we have
a serious problem.
Link: https://lore.kernel.org/r/20220110015018.26359-23-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c36ab437e upstream.
This function is now always used in driver remove method, drop the
__maybe_unused attribute.
Link: https://lore.kernel.org/r/20220110015018.26359-22-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit befa710001 upstream.
By default, all Legacy INTx interrupts are masked, so there is no need to
mask this interrupt during irq_map() callback.
Link: https://lore.kernel.org/r/20220110015018.26359-21-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b08e5b53d1 upstream.
Callback for irq_mask_ack() is the same as for irq_mask(). As there is no
special handling for irq_ack(), there is no need to define irq_mask_ack()
too.
Link: https://lore.kernel.org/r/20220110015018.26359-20-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 815bc31368 upstream.
Emulated root bridge currently provides only one Legacy INTA interrupt
which is used for reporting PCIe PME and ERR events and handled by kernel
PCIe PME and AER drivers.
Aardvark HW reports these PME and ERR events separately, so there is no
need to mix real INTA interrupt and emulated INTA interrupt for PCIe PME
and AER drivers.
Register a new advk-RP (as in Root Port) irq chip and a new irq domain
for emulated root bridge and use this new separate irq domain for
providing INTA interrupt from emulated root bridge for PME and ERR events.
The real INTA interrupt from real devices is now separate.
A custom map_irq callback function on PCI host bridge structure is used to
allocate IRQ mapping for emulated root bridge from new irq domain. Original
callback of_irq_parse_and_map_pci() is used for all other devices as before.
Link: https://lore.kernel.org/r/20220110015018.26359-19-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 273ddd86d6 upstream.
Enable aardvark PME interrupt unconditionally by unmasking it and read PME
requester ID to emulated bridge config space immediately after receiving
interrupt.
PME requester ID is stored in the PCIE_MSG_LOG_REG register, which contains
the last inbound message. So when new inbound message is received by HW
(including non-PM), the content in PCIE_MSG_LOG_REG register is replaced by
a new value.
PCIe specification mandates that subsequent PMEs are kept pending until the
PME Status Register bit is cleared by software by writing a 1b.
Support for masking/unmasking PME interrupt on emulated bridge via
PCI_EXP_RTCTL_PMEIE bit is now implemented only in emulated bridge config
space, to ensure that we do not miss any aardvark PME interrupt.
Reading of PCI_EXP_RTCAP and PCI_EXP_RTSTA registers is simplified as final
value is now always stored into emulated bridge config space by the
interrupt handler, so there is no need to implement support for these
registers in read_pcie callback.
Clearing of W1C bit PCI_EXP_RTSTA_PME is now also simplified as it is done
by pci-bridge-emul.c code for emulated bridge config space. So there is no
need to implement support for clearing this bit in write_pcie callback.
Link: https://lore.kernel.org/r/20220110015018.26359-18-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fc75d8745 upstream.
Currently enabling PCI_EXP_RTSTA_PME bit in PCI_EXP_RTCTL register does
nothing. This is because PCIe PME driver expects to receive PCIe interrupt
defined in PCI_EXP_FLAGS_IRQ register, but aardvark hardware does not
trigger PCIe INTx/MSI interrupt for PME event, rather it triggers custom
aardvark interrupt which this driver is not processing yet.
Fix this issue by handling PME interrupt in advk_pcie_handle_int() and
chaining it to PCIe interrupt 0 with generic_handle_domain_irq() (since
aardvark sets PCI_EXP_FLAGS_IRQ to zero). With this change PCIe PME driver
finally starts receiving PME interrupt.
Link: https://lore.kernel.org/r/20220110015018.26359-17-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7122bcb332 upstream.
To optimize advk_pci_bridge_emul_pcie_conf_write() code, touch
PCIE_ISR0_REG and PCIE_ISR0_MASK_REG registers only when it is really
needed, when processing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME bits.
Link: https://lore.kernel.org/r/20220110015018.26359-16-kabel@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maciej W. Rozycki
Greg Kroah-Hartman
Pali Rohár
Pavan Chebbi
Robert Marko
Mohamed Khalfella
Vidya Sagar
Christian Marangi
Stefan Roese
Shunsuke Mie
Serge Semin
Christoph Hellwig
Miaoqian Lin
Jeffrey Hugo
Lukas Wunner
Johan Hovold
Bjorn Helgaas
Daire McNamara
Kuppuswamy Sathyanarayanan
Francesco Dolcini
Jiantao Zhang
Dan Carpenter
Mario Limonciello
Yicong Yang
Rafael J. Wysocki
Marek Behún