The check that variable val is less than zero is redundant since val
is an unsigned int and hence can never be less than zero. Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM ASM330LHH 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/asm330lhh.pdf
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- use temporary variable in get_mount_matrix()
- remove , after { }
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- use temporary variable in get_mount_matrix()
- remove , after { }
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows to read a mount-matrix device tree
property and report to user-space or in-kernel iio
clients.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows to read a mount-matrix device tree
property and report to user-space or in-kernel iio
clients.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows to read a mount-matrix device tree
property and report to user-space or in-kernel iio
clients.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows to read a mount-matrix device tree
property and report to user-space or in-kernel iio
clients.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows to read a mount-matrix device tree
property and report to user-space or in-kernel iio
clients.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch allows to read a mount-matrix device tree
property and report to user-space or in-kernel iio
clients.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently mount matrix is allowed in Device Tree, though there is
no technical issue to extend it to support ACPI.
Convert the function to use device_property_read_string_array() and
thus allow to read mount matrix from ACPI if available.
Example of use in _DSD method:
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mount-matrix", Package() {
"1", "0", "0",
"0", "0.866", "0.5",
"0", "-0.5", "0.866",
} },
}
})
At the same time drop the "of" prefix from its name and
convert current users.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Solves checkpath.pl's message:
CHECK: Comparison to NULL could be written "!indio_dev"
Signed-off-by: Bárbara Fernandes <barbara.fernandes@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Put macro argument between parenthesis in order to avoid precedence
issues. Solves the following checkpath.pl's messages:
CHECK: Macro argument 'mode' may be better as '(mode)' to avoid
precedence issues
CHECK: Macro argument 'channel' may be better as '(channel)' to
avoid precedence issues
CHECK: Macro argument reuse 'sequence' - possible side-effects?
CHECK: Macro argument 'sequence' may be better as '(sequence)' to
avoid precedence issues
CHECK: Macro argument 'val' may be better as '(val)' to avoid
precedence issues
CHECK: Macro argument 'dec' may be better as '(dec)' to avoid precedence
issues
CHECK: Macro argument 'bits' may be better as '(bits)' to avoid
precedence issues
Signed-off-by: Bárbara Fernandes <barbara.fernandes@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace use of the operation '<<' by the BIT macro. Solves checkpath.pl's
message:
CHECK: Prefer using the BIT macro
Signed-off-by: Bárbara Fernandes <barbara.fernandes@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Get broken line aligned with parenthesis on upper line. Solves
checkpatch.pl's message:
CHECK: Alignment should match open parenthesis
Signed-off-by: Bárbara Fernandes <barbara.fernandes@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add suspend/resume PM sleep ops. When going to low power, disable
active counter. Only active counter should be resumed: don't touch
disabled counter, as it may be used by other LPTimer MFD child driver.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16495 and ADIS16497 are inertial systems that include a triaxis
gyroscope and a triaxis accelerometer. The serial peripheral interface
(SPI) provide a simple interface for data collection and configuration
control. The devices are similar to ADIS16475, ADIS16480, ADIS16485 and
ADIS16488, the main differences are highlighted below:
* The temperature data scale is 0.00565 C/LSB for ADIS16475 and ADIS1648x
devices, while for ADIS1649x 0.0125 C/LSB.
* ADIS1649x devices support different gyroscope measurement ranges which
are dependent on the dash number (-1, -2, -3), see Table 24 in the
ADIS16495 datasheet. However, the ADIS16497 gyroscopes have the same
scale as ADIS16495.
* ADIS16495 devices support the acceleration maximum range of 8g, while
ADIS16497 devices go up to 40g.
* The internal clock for ADIS1649x devices is 4.25 kSPS. The sampling
frequency is calculated by applying a decimation rate which can take a
maximum value of 4250.
* ADIS1649x devices support different default filter frequencies.
Datasheets:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/adis16495.pdf
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/adis16497.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When setting the filter frequency, the driver looks into the
adis16480_def_filter_freqs table for the best match. Pass this table to
the chip_info struct since future devices will need to use a different
table.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adis1648x devices have an internal clock of 2.46 kSPS. The sampling
frequency is calculated by applying a decimation rate which can take the
maximum value of 2047.
Although all adis1648x devices are similar in this regard, devices that
will use this feature will be added in the future.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All supported devices provide internal temperature measurement from -40 C
to +85 C, with +25 C representing value 0x00.
This patch treats the temperature scale in a generic way, similar to the
accelerometer and gyroscope scales. So far, there are no temperature max
scale differences between the supported devices. However, devices that
will make use of this feature will be added in the future.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver does not have a struct of_device_id table, but supported
devices are registered via Device Trees. This patch adds OF device ID
table.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The FNCTIO_CTRL register provides configuration control for each I/O pin
(DIO1, DIO2, DIO3 and DIO4).
This patch adds the option to configure each DIOx pin as data ready
indicator with positive or negative polarity by reading the 'interrupts'
and 'interrupt-names' properties from the devicetree. The
'interrupt-names' property is optional, if it is not specified, then the
DIO1 pin is used as default data ready signal.
Although the factory default assigns DIO2 as data ready signal, in the
versions previous this patch, DIO1 pin was used. We should leave this
configuration as is, since some devices might be expecting the interrupt
on the wrong physical pin.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Indio->mlock is used for protecting the different iio device modes.
It is currently not being used in this way. Replace the lock with
an internal lock specifically used for protecting the SPI transfer
buffer.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If there are more trigger consumers than
CONFIG_IIO_CONSUMERS_PER_TRIGGER, iio_trigger_attach_poll_func will
silently fail. Add an error message to inform the user that
CONFIG_IIO_CONSUMERS_PER_TRIGGER limit might be exceeded.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/iio/accel/mma8452.c: In function ‘mma8452_probe’:
drivers/iio/accel/mma8452.c:1581:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret == data->chip_info->chip_id)
^
drivers/iio/accel/mma8452.c:1584:2: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add other sensors to the compatible list.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
unlikely has already included in IS_ERR(),
so just remove redundant unlikely annotation.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This fixes a possible circular locking dependency detected warning seen
with:
- CONFIG_PROVE_LOCKING=y
- consumer/provider IIO devices (ex: "voltage-divider" consumer of "adc")
When using the IIO consumer interface, e.g. iio_channel_get(), the consumer
device will likely call iio_read_channel_raw() or similar that rely on
'info_exist_lock' mutex.
typically:
...
mutex_lock(&chan->indio_dev->info_exist_lock);
if (chan->indio_dev->info == NULL) {
ret = -ENODEV;
goto err_unlock;
}
ret = do_some_ops()
err_unlock:
mutex_unlock(&chan->indio_dev->info_exist_lock);
return ret;
...
Same mutex is also hold in iio_device_unregister().
The following deadlock warning happens when:
- the consumer device has called an API like iio_read_channel_raw()
at least once.
- the consumer driver is unregistered, removed (unbind from sysfs)
======================================================
WARNING: possible circular locking dependency detected
4.19.24 #577 Not tainted
------------------------------------------------------
sh/372 is trying to acquire lock:
(kn->count#30){++++}, at: kernfs_remove_by_name_ns+0x3c/0x84
but task is already holding lock:
(&dev->info_exist_lock){+.+.}, at: iio_device_unregister+0x18/0x60
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&dev->info_exist_lock){+.+.}:
__mutex_lock+0x70/0xa3c
mutex_lock_nested+0x1c/0x24
iio_read_channel_raw+0x1c/0x60
iio_read_channel_info+0xa8/0xb0
dev_attr_show+0x1c/0x48
sysfs_kf_seq_show+0x84/0xec
seq_read+0x154/0x528
__vfs_read+0x2c/0x15c
vfs_read+0x8c/0x110
ksys_read+0x4c/0xac
ret_fast_syscall+0x0/0x28
0xbedefb60
-> #0 (kn->count#30){++++}:
lock_acquire+0xd8/0x268
__kernfs_remove+0x288/0x374
kernfs_remove_by_name_ns+0x3c/0x84
remove_files+0x34/0x78
sysfs_remove_group+0x40/0x9c
sysfs_remove_groups+0x24/0x34
device_remove_attrs+0x38/0x64
device_del+0x11c/0x360
cdev_device_del+0x14/0x2c
iio_device_unregister+0x24/0x60
release_nodes+0x1bc/0x200
device_release_driver_internal+0x1a0/0x230
unbind_store+0x80/0x130
kernfs_fop_write+0x100/0x1e4
__vfs_write+0x2c/0x160
vfs_write+0xa4/0x17c
ksys_write+0x4c/0xac
ret_fast_syscall+0x0/0x28
0xbe906840
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->info_exist_lock);
lock(kn->count#30);
lock(&dev->info_exist_lock);
lock(kn->count#30);
*** DEADLOCK ***
...
cdev_device_del() can be called without holding the lock. It should be safe
as info_exist_lock prevents kernelspace consumers to use the exported
routines during/after provider removal. cdev_device_del() is for userspace.
Help to reproduce:
See example: Documentation/devicetree/bindings/iio/afe/voltage-divider.txt
sysv {
compatible = "voltage-divider";
io-channels = <&adc 0>;
output-ohms = <22>;
full-ohms = <222>;
};
First, go to iio:deviceX for the "voltage-divider", do one read:
$ cd /sys/bus/iio/devices/iio:deviceX
$ cat in_voltage0_raw
Then, unbind the consumer driver. It triggers above deadlock warning.
$ cd /sys/bus/platform/drivers/iio-rescale/
$ echo sysv > unbind
Note I don't actually expect stable will pick this up all the
way back into IIO being in staging, but if's probably valid that
far back.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Fixes: ac917a8111 ("staging:iio:core set the iio_dev.info pointer to null on unregister")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The desired channel has to be selected in order to correctly fill the
buffer with the corresponding data.
The `ad_sd_write_reg()` already does this, but for the
`ad_sd_read_reg_raw()` this was omitted.
Fixes: af3008485e ("iio:adc: Add common code for ADI Sigma Delta devices")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Without IIO_TRIGGERED_BUFFER, this driver fails to link:
drivers/iio/chemical/pms7003.o: In function `pms7003_probe':
pms7003.c:(.text+0x21c): undefined reference to `devm_iio_triggered_buffer_setup'
pms7003.c:(.text+0x21c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `devm_iio_triggered_buffer_setup'
Fixes: a1d642266c ("iio: chemical: add support for Plantower PMS7003 sensor")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Calculation did not use IIO_DEGREE_TO_RAD and implemented a variant to
avoid precision loss as we aim a nano value. The offset added to avoid
rounding error, though, doesn't give us a close result to the expected
value. E.g.
For 1000dps, the result should be:
(1000 * pi ) / 180 >> 15 ~= 0.000532632218
But with current calculation we get
$ cat scale
0.000547890
Fix the calculation by just doing the maths involved for a nano value
val * pi * 10e12 / (180 * 2^15)
so we get a closer result.
$ cat scale
0.000532632
Fixes: c14dca07a3 ("iio: cros_ec_sensors: add ChromeOS EC Contiguous Sensors driver")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In remove, the clock is disabled before canceling the
delayed work. This means that the delayed work may be
touching unclocked hardware.
Fix by disabling the clock after the delayed work is
fully canceled. This is consistent with the probe error
path order.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If probe errors out after request_irq(), its error path
does not explicitly cancel the delayed work, which may
have been scheduled by the interrupt handler.
This means the delayed work may still be running when
the core frees the private structure (struct xadc).
This is a potential use-after-free.
Fix by inserting cancel_delayed_work_sync() in the probe
error path.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When cancel_delayed_work() returns, the delayed work may still
be running. This means that the core could potentially free
the private structure (struct xadc) while the delayed work
is still using it. This is a potential use-after-free.
Fix by calling cancel_delayed_work_sync(), which waits for
any residual work to finish before returning.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When issuing the write DAC register and write eeprom command, the two
powerdown bits (PD0 and PD1) are assumed by the chip to be present in
the bytes sent. Leaving them at 0 implies "powerdown disabled" which is
a different state that the current one. By adding the current state of
the powerdown in the i2c write, the chip will correctly power-on exactly
like as it is at the moment of store_eeprom call.
This is documented in MCP4725's datasheet, FIGURE 6-2: "Write Commands
for DAC Input Register and EEPROM" and MCP4726's datasheet, FIGURE 6-3:
"Write All Memory Command".
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On some laptops, kxcjk1013 is powered off when system enters S3. We need
restore the range regiter during resume. Otherwise, the sensor doesn't
work properly after S3.
Signed-off-by: he, bo <bo.he@intel.com>
Signed-off-by: Chen, Hu <hu1.chen@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SPI interface implementation was completely broken.
When using the SPI interface, there are only 7 address bits, the upper bit
is controlled by a page select register. The core needs access to both
ranges, so implement register read/write for both regions. The regmap
paging functionality didn't agree with a register that needs to be read
and modified, so I implemented a custom paging algorithm.
This fixes that the device wouldn't even probe in SPI mode.
The SPI interface then isn't different from I2C, merged them into the core,
and the I2C/SPI named registers are no longer needed.
Implemented register value caching for the registers to reduce the I2C/SPI
data transfers considerably.
The calibration set reads as all zeroes until some undefined point in time,
and I couldn't determine what makes it valid. The datasheet mentions these
registers but does not provide any hints on when they become valid, and they
aren't even enumerated in the memory map. So check the calibration and
retry reading it from the device after each measurement until it provides
something valid.
Despite the size this is suitable for a stable backport given that
it seems the SPI support never worked.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The standard unit for temperature is millidegrees Celcius. Adapt the
driver to report in millidegrees instead of degrees.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Fixes: 1b3bd85927 ("iio: chemical: Add support for Bosch BME680 sensor");
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I clearly messed up applying this patch. Not sure
how but the entire Kconfig block is missing. This
patch puts it back as it was in the original patch.
Reported-by: Andreas Brauchli <a.brauchli@elementarea.net>
Fixes: ce51412416 ("iio: chemical: sgp30: Support Sensirion SGP30/SGPC3 sensors")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Having a brief look at at91_adc_read_raw() it is obvious that in the case
of a timeout the setting of AT91_ADC_CHDR and AT91_ADC_IDR registers is
omitted. If 2 different channels are queried we can end up with a
situation where two interrupts are enabled, but only one interrupt is
cleared in the interrupt handler. Resulting in a interrupt loop and a
system hang.
Signed-off-by: Georg Ottinger <g.ottinger@abatec.at>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the datasheet, the last bit of CHIP_ID register controls
I2C bus, and the first one is unused. Handle this correctly.
Note that there are chips out there that have a value such that
the id check currently fails.
Signed-off-by: Sergey Larin <cerg2010cerg2010@mail.ru>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The trialmask is expected to have all bits set to 0 after allocation.
Currently kmalloc_array() is used which does not zero the memory and so
random bits are set. This results in random channels being enabled when
they shouldn't. Replace kmalloc_array() with kcalloc() which has the same
interface but zeros the memory.
Note the fix is actually required earlier than the below fixes tag, but
will require a manual backport due to move from kmalloc to kmalloc_array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Fixes commit 057ac1acdf ("iio: Use kmalloc_array() in iio_scan_mask_set()").
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Standard unit for temperature is millidegrees Celcius, whereas this driver
was reporting in degrees. Fix the scale factor in the driver.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging/iio driver pull request for 5.1-rc1.
Lots of good IIO driver updates and cleanups in here as always.
Combined with the removal of the xgifb driver, we have a net "loss" of
over 9000 lines in the pull request, always a nice thing.
As the outreachy application process is currently happening, there are
loads of tiny checkpatch cleanup fixes all over the staging tree, which
accounts for the majority of the fixups.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+gLQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymBiQCeJpoBhG+W3r+kP8w65ZY8qU+/liIAn0Tkl4/k
IX1dQzCsEpO1jA8AHj6n
=7wCH
-----END PGP SIGNATURE-----
Merge tag 'staging-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big staging/iio driver pull request for 5.1-rc1.
Lots of good IIO driver updates and cleanups in here as always.
Combined with the removal of the xgifb driver, we have a net "loss" of
over 9000 lines in the pull request, always a nice thing.
As the outreachy application process is currently happening, there are
loads of tiny checkpatch cleanup fixes all over the staging tree,
which accounts for the majority of the fixups"
* tag 'staging-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (341 commits)
staging: mt7621-dma: remove license boilerplate text
staging: mt7621-dma: add SPDX GPL-2.0+ license identifier
Staging: ks7010: Replace typecast to int
Staging: vt6655: Align a static function declaration
staging: speakup: fix line over 80 characters.
staging: mt7621-eth: Remove license boilerplate text
staging: mt7621-eth: Add SPDX license identifier
staging: ks7010: removed custom Michael MIC implementation.
staging: rtl8192e: Fix space and suspect issue
Staging: vt6655: Modify comment style of SPDX License Identifier
Staging: vt6655: Modify comment style for SPDX-License-Identifier
Staging: vt6655: Align a function declaration
Staging: vt6655: Alignment of function declaration
staging: rtl8712: Fix indentation issue
staging: wilc1000: fix incorrent type in initializer
staging: rtl8188eu: remove unused P2P_PRIVATE_IOCTL_SET_LEN
staging: rtl8188eu: remove unused enum P2P_PROTO_WK_ID
staging: rtl8723bs: Remove duplicated include from drv_types.h
Staging: vt6655: Alignment should match open parenthesis
staging: erofs: fix mis-acted TAIL merging behavior
...
The pm8xxx_get_channel() implementation is unclear, and causes gcc to
suddenly generate odd warnings. The trigger for the warning (at least
for me) was the entirely unrelated commit 79a4e91d1b ("device.h: Add
__cold to dev_<level> logging functions"), which apparently changes gcc
code generation in the caller function enough to cause this:
drivers/iio/adc/qcom-pm8xxx-xoadc.c: In function ‘pm8xxx_xoadc_probe’:
drivers/iio/adc/qcom-pm8xxx-xoadc.c:633:8: warning: ‘ch’ may be used uninitialized in this function [-Wmaybe-uninitialized]
ret = pm8xxx_read_channel_rsv(adc, ch, AMUX_RSV4,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
&read_nomux_rsv4, true);
~~~~~~~~~~~~~~~~~~~~~~~
drivers/iio/adc/qcom-pm8xxx-xoadc.c:426:27: note: ‘ch’ was declared here
struct pm8xxx_chan_info *ch;
^~
because gcc for some reason then isn't able to see that the termination
condition for the "for( )" loop in that function is also the condition
for returning NULL.
So it's not _actually_ uninitialized, but the function is admittedly
just unnecessarily oddly written.
Simplify and clarify the function, making gcc also see that it always
returns a valid initialized value.
Cc: Joe Perches <joe@perches.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a few late breaking fixes in here that weren't worth trying to
rush into 5.0 as they have been with us for quite a while.
New device support
* ad7476
- add support for TI ADS786X parts that are compatible with this Analog
Devices driver. Good to see some simple devices are so similar.
* Ingenic jz47xx SoC ADCs
- new driver and bindings
* Plantower PMS7003 partical sensor
- new driver and bindings including vendor prefix.
* TI DAC7612
- new driver and bindings for this dual DAC.
New features
* ad7768-1
- Sampling frequency control
* bmi160
- Data ready trigger support, including open-drain dt binding.
Cleanup / minor fixes.
* Analog Device DACs
- Fix some inconsistent licenses. These are only ones where there were
two different license marked in the same file, and hence were previously
unclear.
* ads124s08
- Spelling fix.
* adxl345
- Parameter alignement tidy up.
* bmi160
- SPDX
- correct a note on the types of supported interrupts which was too strict.
- use iio_pollfunc_store_time to grab an earlier timestamp.
- use if (ret) instead of if (ret < 0) to be consistent whilst simplifying
some handling where ret was effectively getting written to 0 even though
it was always already 0.
* exynos_adc
- Fix a null pointer dereference on unbind.
- Fix number of channels on Exynos4x12 devices to be 4 rather than 8.
* lpc32xx-adc
- Move DT bindings doc out of staging. Oops, I missed this one when
moving the driver.
- SPDX.
* npcm-adc
- drop documentation of reset node as going to be done differently.
It's a new driver this cycle so no need to support the previous
binding going forwards.
* sps30
- Fix an issue with a loop timeout test that meant it would never identify
a timeout.
- Mark deliberate switch fall throughs.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlxjNmgRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FogooQ/9HDDuw4hrYJqH2cdUtKV29+a+kvMtrC1i
X9+VstbMQNLo4DM3lYKi4VOeh6P5htRrD9ZJ4I2lh6PfnABjr3lb1AequlxwWNQZ
9EHEY3BA0G33757LQEkqxl7h8Cqvo2y6Wl6OcUund0jP+h3F3EYkI4XWNcq5Yht4
uWTkyTRYVZqFnlXGvfPz+53tEZ6p5RijbhOdYcL8R/0yWYzZzgzut7eYZn8Qn+mR
LzSCBoEyAOUELYyRoczY2EkEO+u8H7lcU43i5TPPKji/c+w4OXu2ktuGVucXaHBs
E1NLp0psLdqR2ef8fNYTs3FO2kxI7jV5qMlR91Sa2lDRyPhYeMF+JYBQlpqm5H2U
xp8WwFrfT4KZ1yvioNeW+aNlPOd6ljDMg1z/iLWpAcUqx65QArmogL64m/Fc5GQD
jrYzw68FO6fqKh3ik7VdPKIUS0p3Dz8BdWOqvI68+C/Mr/TgML51frf1NVbdd36L
qgzMN6N53bykwN2w51O0Af4U3ZednN7BDDFkUbucutoglU+K8yRjFj583wM8QYsG
GOZ3sPVZm+ItWCGc7nTJowe6+EQNgo/md3IEmmZNPrfWPHoMEebqnNcOuqcYvIlj
wXgsJBNlWyQp5bqE9LmgClwAaWkXIoUvjUHt0cK5043ueLrYaGJ698sg0N/UO0JC
T0/PJEMjLPE=
=Se+F
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.1b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, features and cleanup for IIO in the 5.1 cycle.
There are a few late breaking fixes in here that weren't worth trying to
rush into 5.0 as they have been with us for quite a while.
New device support
* ad7476
- add support for TI ADS786X parts that are compatible with this Analog
Devices driver. Good to see some simple devices are so similar.
* Ingenic jz47xx SoC ADCs
- new driver and bindings
* Plantower PMS7003 partical sensor
- new driver and bindings including vendor prefix.
* TI DAC7612
- new driver and bindings for this dual DAC.
New features
* ad7768-1
- Sampling frequency control
* bmi160
- Data ready trigger support, including open-drain dt binding.
Cleanup / minor fixes.
* Analog Device DACs
- Fix some inconsistent licenses. These are only ones where there were
two different license marked in the same file, and hence were previously
unclear.
* ads124s08
- Spelling fix.
* adxl345
- Parameter alignement tidy up.
* bmi160
- SPDX
- correct a note on the types of supported interrupts which was too strict.
- use iio_pollfunc_store_time to grab an earlier timestamp.
- use if (ret) instead of if (ret < 0) to be consistent whilst simplifying
some handling where ret was effectively getting written to 0 even though
it was always already 0.
* exynos_adc
- Fix a null pointer dereference on unbind.
- Fix number of channels on Exynos4x12 devices to be 4 rather than 8.
* lpc32xx-adc
- Move DT bindings doc out of staging. Oops, I missed this one when
moving the driver.
- SPDX.
* npcm-adc
- drop documentation of reset node as going to be done differently.
It's a new driver this cycle so no need to support the previous
binding going forwards.
* sps30
- Fix an issue with a loop timeout test that meant it would never identify
a timeout.
- Mark deliberate switch fall throughs.
* tag 'iio-for-5.1b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (26 commits)
iio: adc: exynos-adc: Use proper number of channels for Exynos4x12
dt-binding: iio: remove rst node from NPCM ADC document
dt-bindings: iio: chemical: pms7003: add device tree support
dt-bindings: add Plantower to the vendor prefixes
iio: chemical: add support for Plantower PMS7003 sensor
iio:chemical:sps30 Supress some switch fallthrough warnings.
iio:adc:lpc32xx use SPDX-License-Identifier
dt-bindings: iio: adc: move lpc32xx-adc out of staging
iio: adc: ads124s08: fix spelling mistake "converions" -> "conversions"
iio: adc: exynos-adc: Fix NULL pointer exception on unbind
iio: chemical: sps30: fix a loop timeout test
iio:accel:adxl345: Change alignment to match paranthesis
iio:dac:dac7612: device tree bindings
iio:dac:ti-dac7612: Add driver for Texas Instruments DAC7612
iio: adc: ad7476: Add support for TI ADS786X ADCs
iio: adc: ad7768-1: Add support for setting the sampling frequency
drivers: iio: dac: Fix wrong license for ADI drivers
IIO: add Ingenic JZ47xx ADC driver.
dt-bindings: iio/adc: Add bindings for Ingenic JZ47xx SoCs ADC.
dt-bindings: iio/adc: Add docs for Ingenic JZ47xx SoCs ADC.
...
Exynos4212 and Exynos4412 have only four ADC channels so using
"samsung,exynos-adc-v1" compatible (for eight channels ADCv1) on them is
wrong. Add a new compatible for Exynos4x12.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Plantower PMS7003 particulate matter sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes warnings reported on linux-next but marking one path
and adding an explicit return in the other.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andreas Brauchli <a.brauchli@elementarea.net>
Acked-by: Tomasz Duszynski <tduszyns@gmail.com>
Convert the driver to SPDX license description which allow removing
several lines in the file.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is a spelling mistake in several dev_err messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix NULL pointer exception on device unbind when device tree does not
contain "has-touchscreen" property. In such case the input device is
not registered so it should not be unregistered.
$ echo "12d10000.adc" > /sys/bus/platform/drivers/exynos-adc/unbind
Unable to handle kernel NULL pointer dereference at virtual address 00000474
...
(input_unregister_device) from [<c0772060>] (exynos_adc_remove+0x20/0x80)
(exynos_adc_remove) from [<c0587d5c>] (platform_drv_remove+0x20/0x40)
(platform_drv_remove) from [<c05860f0>] (device_release_driver_internal+0xdc/0x1ac)
(device_release_driver_internal) from [<c0583ecc>] (unbind_store+0x60/0xd4)
(unbind_store) from [<c031b89c>] (kernfs_fop_write+0x100/0x1e0)
(kernfs_fop_write) from [<c029709c>] (__vfs_write+0x2c/0x17c)
(__vfs_write) from [<c0297374>] (vfs_write+0xa4/0x184)
(vfs_write) from [<c0297594>] (ksys_write+0x4c/0xac)
(ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Fixes: 2bb8ad9b44 ("iio: exynos-adc: add experimental touchscreen support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The "while (tries--) {" loop is a postop so it exits with "tries" set
to -1.
Fixes: 232e0f6dde ("iio: chemical: add support for Sensirion SPS30 sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Align broken line to match upper line parenthesis. Solves the
checkpatch.pl's message:
CHECK: Alignment should match open parenthesis
Signed-off-by: Luciana da Costa Marques <lucianadacostamarques@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is a driver for Texas Instruments Dual, 12-Bit Serial Input
Digital-to-Analog Converter.
Datasheet of this chip:
http://www.ti.com/lit/ds/sbas106/sbas106.pdf
Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Texas Instruments ADS7866, ADS7867 and ADS7868
8/10/12 bit Single channel ADC.
Datasheet: http://www.ti.com/lit/ds/symlink/ads7868.pdf
Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7768-1 core ADC receives a master clock signal (MCLK). The MCLK
frequency combined with the MCLK division and the digital filter
decimation rates, determines the sampling frequency. Along with
MCLK_DIV, the power mode is also configured according to datasheet
recommendations.
From user space, available sampling frequencies can be read. However,
it is not required for an exact value to be entered, since the driver
will look for the closest available match.
When the device configuration changes (for example, if the filter
decimation rate changes), a SYNC_IN pulse is required.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Analog Devices drivers are typically GPL v2 only. This patch fixes the
inconsistencies between the module license and SPDX.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add an IIO driver for the ADC hardware present on Ingenic JZ47xx SoCs.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We are using "if (ret < 0)" in many places in which the function returns 0
on success. Use "if (ret)" instead for better clarity and correctness.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, we snap the timestamp after reading from the buffer and
processing the event. When the IIO poll function is triggered by an
interrupt, we can get a slightly more accurate timestamp by snapping it
prior to reading the data, since the data was already generated prior to
entering the trigger handler. This is not going to make a huge difference,
but we might as well improve slightly.
Do this by using iio_pollfunc_store_time as other drivers do.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add interrupt support for the data ready signal on the BMI160, which fires
an interrupt whenever new accelerometer/gyroscope data is ready to read.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPDX identifiers (GPL 2) for the BMI160 driver. bmi160.h had an
identifier, but the other files did not.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A number of interesting new devices supported plus a good set of staging
cleanup including one graduation and one drop.
New device support
* ad56886
- Add support for AD5674R/AD5679R with some minor driver changes to support
more channels.
* ad7768
- New driver and dt bindings for this 24 bit ADC.
* max44009
- New driver and dt bindings for this ambient light sensor.
* mpu6050
- Support the ICM 20602 IMU. Minor tweaks due to slightly different
register map.
* NPCM adc
- New driver and dt bindings for this BMC ADC.
* Sensiron SGP30
- Modifiers for ethanol and H2.
- New driver and dt bindings.
- Follow patch added self cleaning support.
* Sensiron SPS30
- New channel type for mass concentration.
- New driver and bindings.
- Minor tidy up patch followed (drop fmt specifier as unused)
* st_pressure
- lps22hh support. ID plus information structures and dt bindings.
* ti-ads124s08
- Add binding doc and driver.
Staging graduations
* ad7606 driver and bindings.
Staging drops
* ad7152 CDC driver dropped. This part is near EoL and no one is known
to be using it. If anyone surfaces obviously we can bring the driver
back. If not, good to drop it to avoid wasting anyone's time cleaning
it up.
New features
* bme680
- DT support and bindings doc.
* isl29018
- Add regulator for VCC.
* mag3110
- Add regulators for supplies.
* meson-saradc
- Support the temperature sensors of more SoCs.
* mma8452
- Add regulators for power suplies and binding docs to reflect them.
* st-accel
- Support the undocumented but it seems fairly common _ONT ACPI method
to specify orientation of the sensor.
Cleanup, minor fixes and fixes for staging driver that have been broken a
long time
* ad5933
- Drop platform data alternative to specifying the reference voltage
using a regulator.
- Use the clock framework to contorl the reference clock.
- Add a DT binding doc to cover the defacto binding.
* ad7280a
- Split up some big functions to improve readability.
* ad7606
- Allow for timeout if interrupt never occurs.
- Use devm functions to simplify probe and remove.
- Use the find_closest macro to avoid need for precise values from
userspace.
- Add missing vendor prefixes for various DT properties. Note the
driver is in staging still and there are no known devicetrees.
- Add explict OF device ID table.
- Simplify the Kconfig choices
- Change to a threaded IRQ.
- SPDX and simple stype fixes.
* ad7816
- Drop unnecessary variable init.
* ad9523
- Check a return value that was ignored.
* ad9833
- Drop platform data. It was just setting most values to the hardware
defaults.
- Use the clock framework to provide the input clock.
* adt7316 (lots of staging cleanup)
- Fix some wrong register / bit definitions
- Invert the logic of the check for an ldac pin so it actually makes sense.
- Read the right register to get internal vref settings
- Allow adt751x chips to use the internal vref for all DAC channels rather
than a subset.
- Remove dac vref bypass control from parts that don't have one.
- Make the store DAC update mode function consistent with the show one.
- Fix some spellings and other minor tidy up.
- Avoid passing irq numbers around by putting all the irq logic in
one place.
- Fix an issue with the resolution of DAC control.
- Fix support of the high resolution DAC mode (for temp proportional output)
where supported.
- Fix DAC read and write calculations.
* st_lsm6dsx
- Drop an unused variable (set but not read)
* xilinx-xadc
- Check an unhandled return value.
-----BEGIN PGP SIGNATURE-----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=M03w
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanup for IIO in the 5.1 cycle
A number of interesting new devices supported plus a good set of staging
cleanup including one graduation and one drop.
New device support
* ad56886
- Add support for AD5674R/AD5679R with some minor driver changes to support
more channels.
* ad7768
- New driver and dt bindings for this 24 bit ADC.
* max44009
- New driver and dt bindings for this ambient light sensor.
* mpu6050
- Support the ICM 20602 IMU. Minor tweaks due to slightly different
register map.
* NPCM adc
- New driver and dt bindings for this BMC ADC.
* Sensiron SGP30
- Modifiers for ethanol and H2.
- New driver and dt bindings.
- Follow patch added self cleaning support.
* Sensiron SPS30
- New channel type for mass concentration.
- New driver and bindings.
- Minor tidy up patch followed (drop fmt specifier as unused)
* st_pressure
- lps22hh support. ID plus information structures and dt bindings.
* ti-ads124s08
- Add binding doc and driver.
Staging graduations
* ad7606 driver and bindings.
Staging drops
* ad7152 CDC driver dropped. This part is near EoL and no one is known
to be using it. If anyone surfaces obviously we can bring the driver
back. If not, good to drop it to avoid wasting anyone's time cleaning
it up.
New features
* bme680
- DT support and bindings doc.
* isl29018
- Add regulator for VCC.
* mag3110
- Add regulators for supplies.
* meson-saradc
- Support the temperature sensors of more SoCs.
* mma8452
- Add regulators for power suplies and binding docs to reflect them.
* st-accel
- Support the undocumented but it seems fairly common _ONT ACPI method
to specify orientation of the sensor.
Cleanup, minor fixes and fixes for staging driver that have been broken a
long time
* ad5933
- Drop platform data alternative to specifying the reference voltage
using a regulator.
- Use the clock framework to contorl the reference clock.
- Add a DT binding doc to cover the defacto binding.
* ad7280a
- Split up some big functions to improve readability.
* ad7606
- Allow for timeout if interrupt never occurs.
- Use devm functions to simplify probe and remove.
- Use the find_closest macro to avoid need for precise values from
userspace.
- Add missing vendor prefixes for various DT properties. Note the
driver is in staging still and there are no known devicetrees.
- Add explict OF device ID table.
- Simplify the Kconfig choices
- Change to a threaded IRQ.
- SPDX and simple stype fixes.
* ad7816
- Drop unnecessary variable init.
* ad9523
- Check a return value that was ignored.
* ad9833
- Drop platform data. It was just setting most values to the hardware
defaults.
- Use the clock framework to provide the input clock.
* adt7316 (lots of staging cleanup)
- Fix some wrong register / bit definitions
- Invert the logic of the check for an ldac pin so it actually makes sense.
- Read the right register to get internal vref settings
- Allow adt751x chips to use the internal vref for all DAC channels rather
than a subset.
- Remove dac vref bypass control from parts that don't have one.
- Make the store DAC update mode function consistent with the show one.
- Fix some spellings and other minor tidy up.
- Avoid passing irq numbers around by putting all the irq logic in
one place.
- Fix an issue with the resolution of DAC control.
- Fix support of the high resolution DAC mode (for temp proportional output)
where supported.
- Fix DAC read and write calculations.
* st_lsm6dsx
- Drop an unused variable (set but not read)
* xilinx-xadc
- Check an unhandled return value.
* tag 'iio-for-5.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (67 commits)
iio: chemical: sps30: remove printk format specifier
staging: iio: frequency: ad9833: Load clock using clock framework
staging: iio: frequency: ad9833: Get frequency value statically
dt-bindings: iio: light: Add max44009
iio: light: add driver for MAX44009
dt-bindings: iio: adc: Add docs for AD7768-1
iio: adc: Add AD7768-1 ADC basic support
staging: iio: cdc: ad7152: remove driver completely
iio: imu: mpu6050: Add support for the ICM 20602 IMU
dt-bindings: iio: imu: add icm20602 bindings to mpu6050
dt-bindings: iio: pressure: add LPS22HH bindings
iio: st_accel: use ACPI orientation data
iio: adc: add NPCM ADC driver
dt-binding: iio: add NPCM ADC documentation
iio: chemical: sps30: allow changing self cleaning period
dt-bindings: iio: chemical: Add bindings for bme680
iio: chemical: bme680: Add device-tree support
iio:st_pressure:initial lps22hh sensor support
iio: accell: mma8452: add vdd/vddio regulator operation support
dt-bindings: iio: accel: mma8452: add power supplies property
...
Been a busy month, so these are rather later than they should have been.
* atlas-ph-sensor:
- Temperature scale didn't correspond to the ABI.
* axp288:
- A few different fixes around the TS-pin handling.
* ti-ads8688
- Not enough space in the buffer used to build the scan to allow for
the timestamp.
* tools - iio_generic_buffer
- Make num_loops signed so that we really are running for ever
rather than just a long time when we specify -1.
-----BEGIN PGP SIGNATURE-----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=2R0k
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-5.0a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.0 cycle.
Been a busy month, so these are rather later than they should have been.
* atlas-ph-sensor:
- Temperature scale didn't correspond to the ABI.
* axp288:
- A few different fixes around the TS-pin handling.
* ti-ads8688
- Not enough space in the buffer used to build the scan to allow for
the timestamp.
* tools - iio_generic_buffer
- Make num_loops signed so that we really are running for ever
rather than just a long time when we specify -1.
* tag 'iio-fixes-5.0a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: ti-ads8688: Update buffer allocation for timestamps
tools: iio: iio_generic_buffer: make num_loops signed
iio: adc: axp288: Fix TS-pin handling
iio: chemical: atlas-ph-sensor: correct IIO_TEMP values to millicelsius
pr_fmt is used by printk wrappers. There are not any in the driver
code so remove the format specifier.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MAX44009 is a low-power ambient light sensor from Maxim
Integrated. It differs from the MAX44000 in that it doesn't have
proximity sensing and that it requires far less current (1 micro-amp
vs 5 micro-amps). The register mapping and feature set between the
two are different enough to require a new driver for the MAX44009.
Developed and tested with a BeagleBone Black and UDOO Neo (i.MX6SX)
Supported features:
* Reading lux (processed value)
* Rising and falling illuminance threshold
events
* Configuring integration time
https://datasheets.maximintegrated.com/en/ds/MAX44009.pdf
Signed-off-by: Robert Eshleman <bobbyeshleman@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7768-1 is a single channel, precision 24-bit analog to digital
converter (ADC).
This basic patch configures the device in fast mode, with 32 kSPS and
leaves the default sinc5 filter.
Two data conversion modes are made available. When data is retrieved by
using the read_raw attribute, one shot single conversion mode is set.
The continuous conversion mode is enabled when the triggered buffer
mechanism is used. To assure correct data retrieval, the driver waits
for the interrupt triggered by the low to high transition of the DRDY
pin.
Datasheets:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7768-1.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Invensense ICM-20602 is a 6-axis MotionTracking device that
combines a 3-axis gyroscope and an 3-axis accelerometer. It is very
similar to the ICM-20608 imu which is already supported by the mpu6050
driver. The main difference is that the ICM-20602 has the i2c bus
disable bit in a separate register.
Signed-off-by: Randolph Maaßen <gaireg@gaireg.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Platform-specific ST accelerometer mount matrix information can be
provided by returning a package of 6 integers from the ACPI _ONT
method. This has been seen on Acer products such as Veriton Z4860G,
Z6860G and A890, which include a ST SMO8840 sensor. We have also
confirmed experimentally that the Windows driver uses such information.
The _ONT data format was explained by a ST vendor contact. However,
strangely enough, the _ONT transformations must be applied after first
applying another mount matrix which we determined experimentally. ST
have not commented on why this is the case, but we imagine that perhaps
earlier devices (before _ONT was introduced) required this translation
and hence it became 'standard.'
Interpret the _ONT data and export the equivalent mount matrix to
userspace.
If no _ONT data is present, no mount matrix is exported.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sensor can periodically trigger self cleaning. Period can be changed by
writing a new value to a dedicated attribute. Upon attribute read
current period gets returned.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit allow the driver to work with device-tree.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@gmail.com>
Acked-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Initial support for ST LPS22HH pressure sensor. Datasheet:
http://www2.st.com/resource/en/datasheet/lps22hh.pdf
Features:
* pressure, temperature data and timestamping channels
* sampling frequency selection [1..200] Hz
* interrupt based trigger
* over I2C or SPI interface
Signed-off-by: mario tesi <mario.tesi@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds an ADC driver for the STMPE device using the industrial
input/output interface. The driver supports raw reading of values.
The driver depends on the MFD STMPE driver. If the touchscreen
block is enabled too, only four of the 8 ADC channels are available.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Add support for Power Supply to AXP813
- Add support for GPIO, ADC, AC and Battery Power Supply to AXP803
- Add support for UART to Exynos LPASS
- Fix-ups
- Use supplied MACROS; ti_am335x_tscadc
- Trivial spelling/whitespace/alignment; tmio, axp20x, rave-sp
- Regmap changes; bd9571mwv, wm5110-tables
- Kconfig dependencies; MFD_AT91_USART
- Supply shared data for child-devices; madera-core
- Use new of_node_name_eq() API call; max77620, stmpe
- Use managed resources (devm_*); tps65218
- Comment descriptions; ingenic-tcu
- Coding style; madera-core
- Bug Fixes
- Fix section mismatches; twl-core, db8500-prcmu
- Correct error path related issues; mt6397-core, ab8500-core, mc13xxx-core
- IRQ related fixes; tps6586x
- Ensure proper initialisation sequence; qcom_rpm
- Repair potential memory leak; cros_ec_dev
-----BEGIN PGP SIGNATURE-----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=BwG/
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support
- Add support for Power Supply to AXP813
- Add support for GPIO, ADC, AC and Battery Power Supply to AXP803
- Add support for UART to Exynos LPASS
Fix-ups:
- Use supplied MACROS; ti_am335x_tscadc
- Trivial spelling/whitespace/alignment; tmio, axp20x, rave-sp
- Regmap changes; bd9571mwv, wm5110-tables
- Kconfig dependencies; MFD_AT91_USART
- Supply shared data for child-devices; madera-core
- Use new of_node_name_eq() API call; max77620, stmpe
- Use managed resources (devm_*); tps65218
- Comment descriptions; ingenic-tcu
- Coding style; madera-core
Bug Fixes:
- Fix section mismatches; twl-core, db8500-prcmu
- Correct error path related issues; mt6397-core, ab8500-core, mc13xxx-core
- IRQ related fixes; tps6586x
- Ensure proper initialisation sequence; qcom_rpm
- Repair potential memory leak; cros_ec_dev"
* tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (25 commits)
mfd: exynos-lpass: Enable UART module support
mfd: mc13xxx: Fix a missing check of a register-read failure
mfd: cros_ec: Add commands to control codec
mfd: madera: Remove spurious semicolon in while loop
mfd: rave-sp: Fix typo in rave_sp_checksum comment
mfd: ingenic-tcu: Fix bit field description in header
mfd: tps65218: Use devm_regmap_add_irq_chip and clean up error path in probe()
mfd: Use of_node_name_eq() for node name comparisons
mfd: cros_ec_dev: Add missing mfd_remove_devices() call in remove
mfd: axp20x: Add supported cells for AXP803
mfd: axp20x: Re-align MFD cell entries
mfd: axp20x: Add AC power supply cell for AXP813
mfd: wm5110: Add missing ASRC rate register
mfd: qcom_rpm: write fw_version to CTRL_REG
mfd: tps6586x: Handle interrupts on suspend
mfd: madera: Add shared data for accessory detection
mfd: at91-usart: Add platform dependency
mfd: bd9571mwv: Add volatile register to make DVFS work
mfd: ab8500-core: Return zero in get_register_interruptible()
mfd: tmio: Typo s/use use/use/
...
The accelerometer's power supply could be controllable on some
platforms, such as i.MX6Q-SABRESD board, the mma8451's power supplies
are controlled by a GPIO fixed regulator, need to make sure the
regulators are enabled before any communication with mma8451, this
patch adds vdd/vddio regulator operation support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The light sensor's power supply could be controllable by regulator
on some platforms, such as i.MX6Q-SABRESD board, the light sensor
isl29023's power supply is controlled by a GPIO fixed regulator,
need to make sure the regulator is enabled before any operation of
sensor, this patch adds vcc regulator operation support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The magnetometer's power supplies could be controllable on some platforms,
such as i.MX6Q-SABRESD board, the mag3110's power supplies are controlled
by a GPIO fixed regulator, need to make sure the regulators are enabled
before any communication with mag3110, this patch adds vdd/vddio regulator
operation support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5674R/AD5679R are low power, 16-channel, 12-/16-bit buffered voltage
output digital-to-analog converters (DACs). They include a 2.5 V internal
reference (enabled by default).
These devices are very similar to AD5684R/AD5686R, except that they have 16
channels.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce the TI ADS124S08 and the ADS124S06 ADC
devices from TI. The ADS124S08 is the 12 channel ADC
and the ADS124S06 is the 6 channel ADC device
These devices share a common datasheet:
http://www.ti.com/lit/gpn/ads124s08
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Per Jonathan Cameron, the buffer needs to allocate room for a
64 bit timestamp as well as the channels. Change the buffer
to allocate this additional space.
Fixes: 2a86487786 ("iio: adc: ti-ads8688: add trigger and buffer support")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Prior to this commit there were 3 issues with our handling of the TS-pin:
1) There are 2 ways how the firmware can disable monitoring of the TS-pin
for designs which do not have a temperature-sensor for the battery:
a) Clearing bit 0 of the AXP20X_ADC_EN1 register
b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring
Prior to this commit we were unconditionally setting both bits to the
value used on devices with a TS. This causes the temperature protection to
kick in on devices without a TS, such as the Jumper ezbook v2, causing
them to not charge under Linux.
This commit fixes this by using regmap_update_bits when updating these 2
registers, leaving the 2 mentioned bits alone.
The next 2 problems are related to our handling of the current-source
for the TS-pin. The current-source used for the battery temp-sensor (TS)
is shared with the GPADC. For proper fuel-gauge and charger operation the
TS current-source needs to be permanently on. But to read the GPADC we
need to temporary switch the TS current-source to ondemand, so that the
GPADC can use it, otherwise we will always read an all 0 value.
2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl
register, overwriting various other unrelated bits. Specifically we were
overwriting the current-source setting for the TS and GPIO0 pins, forcing
it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet
this was causing us to get a too high adc value (due to a too high
current-source) resulting in the following errors being logged:
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR
This commit fixes this by using regmap_update_bits to change only the
relevant bits.
3) After reading the GPADC channel we were unconditionally enabling the
TS current-source even on devices where the TS-pin is not used and the
current-source thus was off before axp288_adc_read_raw call.
This commit fixes this by making axp288_adc_set_ts a nop on devices where
the ADC is not enabled for the TS-pin.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545
Fixes: 3091141d78 ("iio: adc: axp288: Fix the GPADC pin ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO_TEMP scale value for temperature was incorrect and not in millicelsius
as required by the ABI documentation.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Fixes: 27dec00ecf (iio: chemical: add Atlas pH-SM sensor support)
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In function xadc_probe, xadc_write_adc_reg can return an error value
when write fails. The fix checks for the return value consistent with
other invocations of the latter function.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8b and Meson8m2 use the same logic to convert the ADC register
value to celsius, which is different from Meson8:
- Meson8 has different multiplier and divider values
- Meson8 uses a 4-bit TSC (temperature sensor coefficient) which fits
into the 4-bit field in the MESON_SAR_ADC_DELTA_10 register:
MESON_SAR_ADC_DELTA_10_TS_C_MASK. Meson8b and Meson8m2 have a 5-bit
TSC which requires writing the upper-most bit into the
MESON_HHI_DPLL_TOP_0[9] register from the HHI register area.
This adds support for the temperature sensor on the Meson8b and Meson8m2
SoCs by implementing the logic to write the upper-most TSC bit into the
HHI register area. The SoC-specific values (temperature_trimming_bits,
temperature_multiplier, temperature_divider) are added - these simply
integrate into the existing infrastructure (which was implemented for
Meson8) and thus require no further changes to the existing temperature
calculation logic.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move ad7606 ADC driver out of staging and into the mainline.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If ad9523_write() fails, indio_dev may get incorrect data. The fix
inserts a check for the return value of ad9523_write(), and it fails,
returns an error.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Self cleaning is especially useful in cases where sensor undergoes
frequent power on/off cycles. In such scenarios it is recommended to
turn self cleaning at least once per week in order to maintain reliable
measurements.
Self cleaning is activated by writing 1 to a dedicated attribute.
Internal fan accelerates to its maximum speed and keeps spinning
for about 10 seconds blowing out accumulated dust.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Tested-by: Andreas Brauchli <andreas.brauchli@sensirion.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big staging and iio driver pull request for 4.21-rc1.
Lots and lots of tiny patches here, nothing major at all. Which is
good, tiny cleanups is nice to see. No new huge driver removal or
addition, this release cycle, although there are lots of good IIO driver
changes, addtions, and movement from staging into the "real" part of the
kernel, which is always great.
Full details are in the shortlog, and all of these have been in
linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCY93w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymJRwCfeV0x/+IMS0UGh9ltHnUfCfR9bcgAmgPWMPnY
bauRCLkceTjzODOR4SzH
=o6Fs
-----END PGP SIGNATURE-----
Merge tag 'staging-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and iio driver pull request for 4.21-rc1.
Lots and lots of tiny patches here, nothing major at all. Which is
good, tiny cleanups is nice to see. No new huge driver removal or
addition, this release cycle, although there are lots of good IIO
driver changes, addtions, and movement from staging into the "real"
part of the kernel, which is always great.
Full details are in the shortlog, and all of these have been in
linux-next for a while with no reported issues"
* tag 'staging-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (553 commits)
staging: mt7621-mmc: Correct spelling mistakes in comments
staging: wilc1000: fix missing read_write setting when reading data
mt7621-mmc: char * array declaration might be better as static const
mt7621-mmc: return statement in void function unnecessary
mt7621-mmc: Alignment should match open parenthesis
mt7621-mmc: Removed unnecessary blank lines
mt7621-mmc: Fix some coding style issues
staging: android: ashmem: doc: Fix spelling
staging: rtl8188eu: cleanup brace coding style issues
staging: rtl8188eu: add spaces around '&' in rtw_mlme_ext.c
staging: rtl8188eu: change return type of is_basicrate() to bool
staging: rtl8188eu: simplify null array initializations
staging: rtl8188eu: change order of declarations to improve readability
staging: rtl8188eu: make some arrays static in rtw_mlme_ext.c
staging: rtl8188eu: constify some arrays
staging: rtl8188eu: convert unsigned char arrays to u8
staging: rtl8188eu: remove redundant declaration in rtw_mlme_ext.c
staging: rtl8188eu: remove unused arrays WFD_OUI and WMM_INFO_OUI
staging: rtl8188eu: remove unnecessary parentheses in rtw_mlme_ext.c
staging: rtl8188eu: remove unnecessary comments in rtw_mlme_ext.c
...
The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
Touchscreen support is added for the Mediacom Flexbook Edge 11.
Mellanox driver got fixed due to updates in their firmware.
The power management stub driver for AtomISP v2 is fixed in order to support
Intel Baytrail SoCs where same quirk is needed for S0ix to work.
Special key handling has been fixed for Favorites hotkey on Thinkpad, and
Screen LOCK on ASUS.
Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been updated
to support this.
Few cleanups related to debugfs have been made in Intel IPS and
Intel PMC drivers. Besides that Intel PMC has been extended
to show more detailed information about Latency Tolerance.
The following is an automated git shortlog grouped by driver:
ACPI / scan:
- Create platform device for INT3515 ACPI nodes
Add the VLV ISP PCI ID to atomisp2_pm:
- Add the VLV ISP PCI ID to atomisp2_pm
asus-nb-wmi:
- Drop mapping of 0x33 and 0x34 scan codes
- Map 0x35 to KEY_SCREENLOCK
asus-wmi:
- Tell the EC the OS will handle the display off hotkey
dell-laptop:
- Mark expected switch fall-throughs
Documentation/ABI:
- Add new attribute for mlxreg-io sysfs interfaces
Fix config space access for intel_atomisp2_pm:
- Fix config space access for intel_atomisp2_pm
i2c:
- acpi: Introduce i2c_acpi_get_i2c_resource() helper
- acpi: Use ACPI_FAILURE instead of !ACPI_SUCCESS
- acpi: Return error pointers from i2c_acpi_new_device()
i2c-multi-instantiate:
- Allow to have same slaves
- Introduce IOAPIC IRQ support
- Distinguish IRQ resource type
- Count I2cSerialBus() resources
- Get rid of obsolete conditional
- Defer probe when no adapter found
- Accept errors of i2c_acpi_new_device()
ideapad-laptop:
- Add Yoga 2 13 to no_hw_rfkill list
iio:
- inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
intel_cht_int33fe:
- Get rid of obsolete conditional
- Accept errors of i2c_acpi_new_device()
- Remove duplicate NULL check
intel_ips:
- Convert to use DEFINE_SHOW_ATTRIBUTE macro
- Remove never happen condition
- NULL check before some freeing functions is not needed
- remove unnecessary checks in ips_debugfs_init
intel_pmc_core:
- convert to DEFINE_SHOW_ATTRIBUTE
- Decode Snoop / Non Snoop LTR
- Fix LTR IGNORE Max offset
- Show Latency Tolerance info
intel_telemetry:
- convert to DEFINE_SHOW_ATTRIBUTE
mlx-platform:
- Convert to use SPDX identifier
- Allow mlxreg-io driver activation for new systems
- Fix LED configuration
- Fix tachometer registers
- Rename new systems product names
- Add definitions for new registers
thinkpad_acpi:
- Cleanup quirks macros
- Change the keymap for Favorites hotkey
touchscreen_dmi:
- Add info for the Mediacom Flexbook Edge 11
-----BEGIN PGP SIGNATURE-----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=kYH6
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- The USB Power Delivery discrete components now can be enumerated by
i2c-multi-instantiate driver via several resources under single ACPI
device node (ACPI ID is INT3515).
- Touchscreen support is added for the Mediacom Flexbook Edge 11.
- Mellanox driver got fixed due to updates in their firmware.
- The power management stub driver for AtomISP v2 is fixed in order to
support Intel Baytrail SoCs where same quirk is needed for S0ix to
work.
- Special key handling has been fixed for Favorites hotkey on Thinkpad,
and Screen LOCK on ASUS.
- Ideapad Yoga 2 13 has no HW rfkill switch, thus, driver has been
updated to support this.
- Few cleanups related to debugfs have been made in Intel IPS and Intel
PMC drivers. Besides that Intel PMC has been extended to show more
detailed information about Latency Tolerance
* tag 'platform-drivers-x86-v4.21-1' of git://git.infradead.org/linux-platform-drivers-x86: (41 commits)
platform/x86: mlx-platform: Convert to use SPDX identifier
Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
platform/x86: mlx-platform: Allow mlxreg-io driver activation for new systems
platform/x86: mlx-platform: Fix LED configuration
platform/x86: mlx-platform: Fix tachometer registers
platform/x86: mlx-platform: Rename new systems product names
platform/x86: mlx-platform: Add definitions for new registers
platform/x86: intel_telemetry: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: intel_pmc_core: convert to DEFINE_SHOW_ATTRIBUTE
platform/x86: thinkpad_acpi: Cleanup quirks macros
platform/x86: touchscreen_dmi: Add info for the Mediacom Flexbook Edge 11
platform/x86: Fix config space access for intel_atomisp2_pm
platform/x86: Add the VLV ISP PCI ID to atomisp2_pm
platform/x86: intel_ips: Convert to use DEFINE_SHOW_ATTRIBUTE macro
platform/x86: intel_ips: Remove never happen condition
platform/x86: intel_ips: NULL check before some freeing functions is not needed
platform/x86: intel_ips: remove unnecessary checks in ips_debugfs_init
iio: inv_mpu6050: Use i2c_acpi_get_i2c_resource() helper
ACPI / scan: Create platform device for INT3515 ACPI nodes
platform/x86: i2c-multi-instantiate: Allow to have same slaves
...
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c: In function 'st_lsm6dsx_shub_read_reg':
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_shub.c:108:41: warning:
variable 'hub_settings' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit c91c1c844e ("iio: imu: st_lsm6dsx:
add i2c embedded controller support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support Sensirion SGP30 and SGPC3 multi-pixel I2C gas sensors
Supported Features:
* Indoor Air Quality (IAQ) concentrations for
- tVOC (in_concentration_voc_input)
- CO2eq (in_concentration_co2_input) - SGP30 only
IAQ concentrations are periodically read out by a background thread
to allow the sensor to maintain its internal baseline.
* Gas concentration signals
- Ethanol (in_concentration_ethanol_raw)
- H2 (in_concentration_h2_raw) - SGP30 only
https://www.sensirion.com/file/datasheet_sgp30https://www.sensirion.com/file/datasheet_sgpc3
Signed-off-by: Andreas Brauchli <andreas.brauchli@sensirion.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for Sensirion SPS30 particulate matter sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Measuring particulate matter in ug / m3 (micro-grams per cubic meter)
is de facto standard. Existing air quality sensors usually follow
this convention and are capable of returning measurements using
this unit.
IIO currently does not offer suitable channel type for this
type of measurements hence this patch adds this.
In addition, extra modifiers are introduced used for distinguishing
between fine pm1, pm2p5 and coarse pm4, pm10 particle measurements, i.e
IIO_MOD_PM1, IIO_MOD_PM25 and IIO_MOD_PM4, IIO_MOD_PM10.
pmX consists of particles with aerodynamic diameter less or equal to
X micrometers.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Staging graduation
* ad2s90
- Driver for this resolver to digital chip.
New drivers and device support.
* ad5686
- Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
- Support for S5PV210 which is slightly different from other parts.
* mcp41010
- Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
MCP42100 microchip potentiometers.
New ACPI ids.
* ak8975
- AKM9911 ACPI HID.
* kxcjk-1013
- KXJ2109 ACPI HID.
- KIOX010A ACPI HID.
New features
* ad5933
- Explicit DT binding.
* ad2s90
- Explicit DT binding including dropping spi setup that is done via dt
in favour of verifying the settings form DT.
* adt7316
- Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
- Runtime power management.
Minor fixes and cleanups
* core
- Protect against missing info structure.
* ad2s90
- SPDX
- Add documentation fo the mutex.
* ad7280a
- Check allocation failure.
- Fix an accidental replacement of an error return.
* adt7316
- Switch some variables to be local and rename for consistency with other
drivers.
- Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
- Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
- White space cleanup.
* hts221
- MAINTAINERS entry.
* lis302
- Use generic name in the DT binding doc.
* Messon-saradc
- Check for allocation error.
- Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
- A fix for initialization of the prescale property. Came late in the
cycle, so merge window is probably the best route for this.
* st_lsm6dsx
- Allow for variable read length to support wider range of slave devices.
-----BEGIN PGP SIGNATURE-----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=+vyl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups for the 4.21 cycle.
Staging graduation
* ad2s90
- Driver for this resolver to digital chip.
New drivers and device support.
* ad5686
- Add support for ad5310r DAC and associated fix in value read back.
* exynos-adc
- Support for S5PV210 which is slightly different from other parts.
* mcp41010
- Driver supporting MCP41010, MCP41050, MCP41100, MCP42010, MCP42050 and
MCP42100 microchip potentiometers.
New ACPI ids.
* ak8975
- AKM9911 ACPI HID.
* kxcjk-1013
- KXJ2109 ACPI HID.
- KIOX010A ACPI HID.
New features
* ad5933
- Explicit DT binding.
* ad2s90
- Explicit DT binding including dropping spi setup that is done via dt
in favour of verifying the settings form DT.
* adt7316
- Explicit DT binding and support for gpio, irq_flags etc.
* stm32-adc
- Runtime power management.
Minor fixes and cleanups
* core
- Protect against missing info structure.
* ad2s90
- SPDX
- Add documentation fo the mutex.
* ad7280a
- Check allocation failure.
- Fix an accidental replacement of an error return.
* adt7316
- Switch some variables to be local and rename for consistency with other
drivers.
- Revert a false handling of 0 as an error introduced earlier this cycle.
* bmi160
- Use devm functions throughout probe() to avoid need for remove().
* hid-sensor-hub
- White space cleanup.
* hts221
- MAINTAINERS entry.
* lis302
- Use generic name in the DT binding doc.
* Messon-saradc
- Check for allocation error.
- Fix some presented clock names that break clk debugfs.
* qcom-spmi-adc
- A fix for initialization of the prescale property. Came late in the
cycle, so merge window is probably the best route for this.
* st_lsm6dsx
- Allow for variable read length to support wider range of slave devices.
* tag 'iio-for-4.21b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (37 commits)
iio: adc: qcom-spmi-adc5: Initialize prescale properly
dt-bindings: iio: adc: exynos-adc: Add S5PV210 variant
iio: adc: Allow selection of Exynos ADC on S5PV210
iio: adc: exynos-adc: Add S5PV210 variant
iio: bmi160: use all devm functions in probe
iio: dac: ad5686: fix bit shift read register
iio:dac:ad5686: Add AD5310R support
Revert "Staging: iio: adt7316: Add an extra check for 'ret' equals to 0"
dt-bindings: iio: accel: use a generic node name for lis302
iio: core: check 'info' value before registering the device
staging: iio: adc: ad7280a: fix overwrite of the returned value
staging: iio: adc: ad7280a: check for devm_kasprint() failure
iio: humidity: hts221: add entry in MAINTAINERS file
iio: magnetometer: ak8975: Add the "AKM9911" ACPI HID
staging:iio:ad2s90: Move out of staging
staging:iio:ad2s90: Add comment to device state mutex
staging:iio:ad2s90: Replace license text w/ SPDX identifier
dt-bindings:iio:resolver: Add docs for ad2s90
staging:iio:ad2s90: Add max frequency check at probe
staging:iio:ad2s90: Remove spi setup that should be done via dt
...
adc5_get_dt_data uses a local, prop, feeds it to adc5_get_dt_channel_data,
and then puts the result into adc->chan_props. The problem is
adc5_get_dt_channel_data may not initialize that structure fully, so a
garbage value is used for prescale if the optional "qcom,pre-scaling" is
not defined in DT. adc5_read_raw then uses this as an array index,
generating a crash that looks like this:
[ 6.683186] Unable to handle kernel paging request at virtual address ffffff90e78c7964
Call trace:
qcom_vadc_scale_code_voltage_factor+0x74/0x104
qcom_vadc_scale_hw_calib_die_temp+0x20/0x60
qcom_adc5_hw_scale+0x78/0xa4
adc5_read_raw+0x3d0/0x65c
iio_channel_read+0x240/0x30c
iio_read_channel_processed+0x10c/0x150
qpnp_tm_get_temp+0xc0/0x40c
of_thermal_get_temp+0x7c/0x98
thermal_zone_get_temp+0xac/0xd8
thermal_zone_device_update+0xc0/0x38c
qpnp_tm_probe+0x624/0x81c
platform_drv_probe+0xe4/0x11c
really_probe+0x188/0x3fc
driver_probe_device+0xb8/0x188
__device_attach_driver+0x114/0x180
bus_for_each_drv+0xd8/0x118
__device_attach+0x180/0x27c
device_initial_probe+0x20/0x2c
bus_probe_device+0x78/0x124
deferred_probe_work_func+0xfc/0x138
process_one_work+0x3d8/0x8b0
process_scheduled_works+0x48/0x6c
worker_thread+0x488/0x7cc
kthread+0x24c/0x264
ret_from_fork+0x10/0x18
Unfortunately, when I went to add the initializer for this and tried to
boot it, my machine shut down immediately, complaining that it was
hotter than the sun. It appears that adc5_chans_pmic and adc5_chans_rev2
were initializing prescale_index as if it were directly a divisor,
rather than the index into adc5_prescale_ratios that it is.
Fix the uninitialized value, and change the static initialization to use
indices into adc5_prescale_ratios.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make it possible to use Exynos ADC driver on S5PV210 based devices.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
S5PV210's ADC variant is almost the same as v1 except that it has 10
channels and doesn't require the pmu register
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, we're using the devm version of some but not all functions.
Switch to the devm version of iio_triggered_buffer_setup and
iio_device_register to simplify the code a bit and decrease the chance of
bugs.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch solves the register readback issue with the bit shift. When the
dac resolution was lower than the register size (ex. 12 bits out of 16
bits) the readback value was not shifted with the difference in bits and
the value was higher. Also a mask is applied on the read value in order to
get the value relative to the actual bit size.
Fixes: 0357e488b8 ("iio:dac:ad5686: Refactor the driver")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD5310R is a single channel DAC with 10-bit precision, which is
part of the same family as AD5311R, except that it uses the spi interface
instead of i2c. The device has a built-in 2.5V reference which is enabled
by default.
Another important difference is that the SPI write command operation is
16 bits long. The first four bits represent the command, while the
remaining 12 bits are for data. In the control reg, DB9 and DB10 are used
for power-down modes, while DB8 is the REF bit. In order to accommodate
this change, a new regmap type was defined and checked accordingly.
Because AD5310R does not have a readback register, the read_raw operation
will return "Operation is not supported".
Datasheet:
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/AD5310R_5311R.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the 'info' structure inside indio_dev is left uninitialized,
a segmentation fault occurs.
Check the 'info' value before using it and if it is equal to
NULL, return with -EINVAL.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI provides a generic helper to get I2C Serial Bus resources.
Use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When performing single ended measurements with TSCADC, its recommended
to set negative input (SEL_INM_SWC_3_0) of ADC step to ADC's VREFN in the
corresponding STEP_CONFIGx register.
Also, the positive(SEL_RFP_SWC_2_0) and negative(SEL_RFM_SWC_1_0)
reference voltage for ADC step needs to be set to VREFP and VREFN
respectively in STEP_CONFIGx register.
Without these changes, there may be variation of as much as ~2% in the
ADC's digital output which is bad for precise measurement.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This HID is used on the ASUS MeMO Pad 7 (ME176C) tablet.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move ad2s90 resolver driver out of staging to the main tree.
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Victor Colombo <victorcolombo@gmail.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Generalize st_lsm6dsx_shub_read_oneshot in order to not use a fixed
read length and take into account iio channel realbits for single
read operations
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The statement is indented too much by one level, fix this by
removing the extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Switch off ADC when going to low power mode, in case it has been left
running in buffer mode. Then re-enable it when resuming.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for runtime PM & sleep. Move all regulator and clock management
to dedicated HW start/stop routines. Then rely on (runtime) PM OPS to
call them.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move self-calibration routine to prepare routine.
- This is precursor patch to ease power management handling.
- This also allow to factorize few error cases (error handling).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Various 2-in-1's use KIOX010A and KIOX020A as HIDs for 2 KXCJ91008
accelerometers. The KIOX010A HID is for the one in the base and the
KIOX020A for the accelerometer in the keyboard.
Since userspace does not have a way yet to deal with (or ignore) the
accelerometer in the keyboard, this commit just adds the KIOX010A HID
for now so that display rotation will work.
Related: https://github.com/hadess/iio-sensor-proxy/issues/166
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this patch we are registering the internal clocks (for example on
Meson8b, where the SAR ADC IP block implements the divider and gate
clocks) with the following names:
- /soc/cbus@c1100000/adc@8680#adc_div
- /soc/cbus@c1100000/adc@8680#adc_en
This is bad because the common clock framework uses the clock to create
a directory in <debugfs>/clk. With such name, the directory creation
(silently) fails and the debugfs entry ends up being created at the
debugfs root.
With this change, the new clock names are:
- c1108680.adc#adc_div
- c1108680.adc#adc_en
This matches the clock naming scheme used in the PWM, Ethernet and MMC
drivers. It also fixes the problem with debugfs.
The idea is shamelessly taken from commit b96e9eb628 ("pwm: meson:
Fix mux clock names").
Fixes: 3921db46a8 ("iio: Convert to using %pOF instead of full_name")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
devm_kasprintf() may return NULL on failure of internal allocation thus
the assignments to init.name are not safe if not checked. On error
meson_sar_adc_clk_init() returns negative values so -ENOMEM in the
(unlikely) failure case of devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This HID is used on the ASUS MeMO Pad 7 (ME176C) tablet.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Along with the headline feature of 5 new drivers, we have the
substantial addition of auxilliary sensor support on the lsm6sdx
parts for ST. There has also been a good set of staging cleanup
in this period with more underway.
An ever increasing number of devices supported with just a new
ID which is a good sign that at least some manufacturers are
continuing to stabilise their interfaces.
New device support,
* ad7124
- New driver supporting Analog Devices' ad7124-4 and ad7124-8 parts
with the inevitable DT binding.
* ad7949
- New driver supporting Analog Devices' ad7949, AD7682 and AD7689 ADCs.
* rm3100
- New driver supporting PNIs RM3100 magnometer with bindings and
vendor prefix.
* ti-dac7311
- New driver supporting DAC7311, DAC6311 and DAC5311 TI DACs, with
DT bindings.
* vcnl5035
- New driver supporting the light sensor part of the VCNL4035, with
DT bindings
Features,
* bindings
- Add a generic ADC channel binding as we keep reinventing this
wheel.
* adc128s052
- Add IDs for additional pin compatible parts.
- Add APCI ID seen on E3940 UP squared boards.
* ad_sigma_delta
- Allow for custom data register overiding default.
* kxcjk1013
- Add KIOX0009 ACPI ID as seen on the Acer One 10.
* lsm6dsx
- Rework leading to...
- External sensor support using the built in I2C master.
- Initial support for a slave lis2mdl magnetometer.
* meson-saradc
- Add temperature sensor support and bindings.
* st_magn
- New ID for lsm9dsl_magn with bindings
- New ID for lis3de accelerometer
* tpl0102
- Add supprot for IIO_AVAIL_RANGE to report the range available
from this device to userspace and in kernel users.
Cleanups and minor fixes
* tools
- Allow outside specification of CFLAGS
* ad2s90
- Handle and spi_read error.
- Handle spi_setup failure
- Drop a pointless assignment.
- Prevent a potentail race by moving device registration to after
all other setup.
- Add missing scale attribute.
- Add a sanity check on channel type before trying to read it.
* ad2s1210
- Move to modern gpio descriptors.
- Drop a gpioin flag which made no sense as far as we can tell.
- Add dt table (bindings doc to follow when this is ready for
moving out of staging).
* ad5933
- Drop camel-case naming of ext_clk_hz.
- White space fixes.
* ad7150
- Local variable to shorten overly long line.
- Alignment and line break fixes.
* ad7280a
- Handle an error path that was previously ignored.
- Use crc8.h to build the crc table replacing custom code.
- Avoid unecessary cast.
- Power down the device if an error happens in probe
- Use devm routines to simplify probe and remove.
* ad7606
- Alignment fixes.
* ad7780
- This worked as long as by coincidence an uninitialized value
was 0. Lets not rely on that.
- Ensure gain update is only used with the ad778x chips that
actually support it.
- Tidy up pattern mask generation.
- Read regulator when scale is requested (which should be infrequent)
as it might have changed from initialization.
* ad7816
- Move to modern gpio descriptors
- Don't use a busy_pin for ad7818 as there isn't one.
- Ensure RD/WR and CONVST pins are outputs (previously they
were brought up as inputs which doesn't seem to make any sense)
- DT id table.
* adc128s052
- SPDX
* adt7316
- Alignment fix.
- Fix data reading. When using I2C the driver never actually
used the value read. This has been broken a very long time
hence no rush to fix it now + the driver is undergoing a lot
of cleanup.
- Sanity check that the i2c read didn't fail to actually read
anything.
* dpot-dac
- Mark a switch full through with slightly different text so that
gcc doesn't warn on it.
* gyro-adc
- Fix a wrong file in the MAINTAINERS entry and add binding doc to the
listed files.
* ina2xx
- Add some early returns to clarify error paths in switch.
* lsm6dsx
- MAINTAINERS entry.
* max11100
- SPDX
* max9611
- SPDX
* mcp4131
- use of_device_get_match_data in preference to spi_get_device_id
approach.
* rcar-adc
- SPDX
* sc27xx
- Add ADC conversion timeout support to avoid possible fault.
* ssp_sensors
- Don't free managed resources manually.
* st-magn
- Add a comment to avoid future confusion over when to use -magn
postfix (on multi chip in package parts)
- Add BDU register for LIS3MDL where it seems to have been missed.
* st-sensors
- Minor spelling, grammar etc fixes.
* tpl0102
- Use a pointer rather than an index of an array to improve conciseness.
-----BEGIN PGP SIGNATURE-----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=78Y3
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.21 cycle
Along with the headline feature of 5 new drivers, we have the
substantial addition of auxilliary sensor support on the lsm6sdx
parts for ST. There has also been a good set of staging cleanup
in this period with more underway.
An ever increasing number of devices supported with just a new
ID which is a good sign that at least some manufacturers are
continuing to stabilise their interfaces.
New device support,
* ad7124
- New driver supporting Analog Devices' ad7124-4 and ad7124-8 parts
with the inevitable DT binding.
* ad7949
- New driver supporting Analog Devices' ad7949, AD7682 and AD7689 ADCs.
* rm3100
- New driver supporting PNIs RM3100 magnometer with bindings and
vendor prefix.
* ti-dac7311
- New driver supporting DAC7311, DAC6311 and DAC5311 TI DACs, with
DT bindings.
* vcnl5035
- New driver supporting the light sensor part of the VCNL4035, with
DT bindings
Features,
* bindings
- Add a generic ADC channel binding as we keep reinventing this
wheel.
* adc128s052
- Add IDs for additional pin compatible parts.
- Add APCI ID seen on E3940 UP squared boards.
* ad_sigma_delta
- Allow for custom data register overiding default.
* kxcjk1013
- Add KIOX0009 ACPI ID as seen on the Acer One 10.
* lsm6dsx
- Rework leading to...
- External sensor support using the built in I2C master.
- Initial support for a slave lis2mdl magnetometer.
* meson-saradc
- Add temperature sensor support and bindings.
* st_magn
- New ID for lsm9dsl_magn with bindings
- New ID for lis3de accelerometer
* tpl0102
- Add supprot for IIO_AVAIL_RANGE to report the range available
from this device to userspace and in kernel users.
Cleanups and minor fixes
* tools
- Allow outside specification of CFLAGS
* ad2s90
- Handle and spi_read error.
- Handle spi_setup failure
- Drop a pointless assignment.
- Prevent a potentail race by moving device registration to after
all other setup.
- Add missing scale attribute.
- Add a sanity check on channel type before trying to read it.
* ad2s1210
- Move to modern gpio descriptors.
- Drop a gpioin flag which made no sense as far as we can tell.
- Add dt table (bindings doc to follow when this is ready for
moving out of staging).
* ad5933
- Drop camel-case naming of ext_clk_hz.
- White space fixes.
* ad7150
- Local variable to shorten overly long line.
- Alignment and line break fixes.
* ad7280a
- Handle an error path that was previously ignored.
- Use crc8.h to build the crc table replacing custom code.
- Avoid unecessary cast.
- Power down the device if an error happens in probe
- Use devm routines to simplify probe and remove.
* ad7606
- Alignment fixes.
* ad7780
- This worked as long as by coincidence an uninitialized value
was 0. Lets not rely on that.
- Ensure gain update is only used with the ad778x chips that
actually support it.
- Tidy up pattern mask generation.
- Read regulator when scale is requested (which should be infrequent)
as it might have changed from initialization.
* ad7816
- Move to modern gpio descriptors
- Don't use a busy_pin for ad7818 as there isn't one.
- Ensure RD/WR and CONVST pins are outputs (previously they
were brought up as inputs which doesn't seem to make any sense)
- DT id table.
* adc128s052
- SPDX
* adt7316
- Alignment fix.
- Fix data reading. When using I2C the driver never actually
used the value read. This has been broken a very long time
hence no rush to fix it now + the driver is undergoing a lot
of cleanup.
- Sanity check that the i2c read didn't fail to actually read
anything.
* dpot-dac
- Mark a switch full through with slightly different text so that
gcc doesn't warn on it.
* gyro-adc
- Fix a wrong file in the MAINTAINERS entry and add binding doc to the
listed files.
* ina2xx
- Add some early returns to clarify error paths in switch.
* lsm6dsx
- MAINTAINERS entry.
* max11100
- SPDX
* max9611
- SPDX
* mcp4131
- use of_device_get_match_data in preference to spi_get_device_id
approach.
* rcar-adc
- SPDX
* sc27xx
- Add ADC conversion timeout support to avoid possible fault.
* ssp_sensors
- Don't free managed resources manually.
* st-magn
- Add a comment to avoid future confusion over when to use -magn
postfix (on multi chip in package parts)
- Add BDU register for LIS3MDL where it seems to have been missed.
* st-sensors
- Minor spelling, grammar etc fixes.
* tpl0102
- Use a pointer rather than an index of an array to improve conciseness.
* tag 'iio-for-4.21a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (80 commits)
Staging: iio: adt7316: Add an extra check for 'ret' equals to 0
Staging: iio: adt7316: Fix i2c data reading, set the data field
dt-bindings: iio: adc: Add docs for ad7124
iio: adc: Add ad7124 support
dt-bindings: iio: adc: Add common ADCs properties to a separate file
iio: ad_sigma_delta: Allow to provide custom data register address
staging: iio: ad7816: Add device tree table.
iio: imu: st_lsm6dsx: add entry in MAINTAINERS file
iio: potentiometer: mcp4131: use of_device_get_match_data()
staging: iio: adc: ad7280a: use devm_* APIs
staging: iio: adc: ad7280a: power down the device on error in probe
dt-bindings: iio: imu: st_lsm6dsx: add support to i2c pullup resistors
iio: imu: st_lsm6dsx: add hw FIFO support to i2c controller
iio: imu: st_lsm6dsx: add st_lsm6dsx_push_tagged_data routine
iio: imu: st_lsm6dsx: add i2c embedded controller support
iio: imu: st_lsm6dsx: introduce st_lsm6dsx_sensor_set_enable routine
iio: imu: st_lsm6dsx: introduce ST_LSM6DSX_ID_EXT sensor ids
iio: imu: st_lsm6dsx: remove static from st_lsm6dsx_set_watermark
iio: imu: st_lsm6dsx: reload trimming parameter at bootstrap
iio: imu: st_lsm6dsx: introduce locked read/write utility routines
...
The ad7124-4 and ad7124-8 are a family of 4 and 8 channel sigma-delta ADCs
with 24-bit precision and reference.
Three power modes are available which in turn affect the output data rate:
* Full power: 9.38 SPS to 19,200 SPS
* Mid power: 2.34 SPS to 4800 SPS
* Low power: 1.17 SPS to 2400 SPS
The ad7124-4 can be configured to have four differential inputs, while
ad7124-8 can have 8. Moreover, ad7124 also supports per channel
configuration. Each configuration consists of gain, reference source,
output data rate and bipolar/unipolar configuration.
Datasheets:
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/AD7124-4.pdf
Link: http://www.analog.com/media/en/technical-documentation/data-sheets/ad7124-8.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some newer devices from the Sigma-Delta ADC family do have their data
register at a different address than the current default address. Add a
parameter to the ad_sigma_delta_info struct which allows to override the
default address.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Try to get the device's data using OF API. In case of failure, fallback
to the spi_get_device_id() method.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce hw FIFO support to lsm6dsx i2c controller.
st_lsm6dsx sensor-hub relies on SLV0 for slave configuration since SLV0
is the only channel that can be used to write into i2c slave devices.
SLV{1,2,3} channels are used to read external data and push them into
the hw FIFO
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce st_lsm6dsx_push_tagged_data routine to push samples
to iio buffers. st_lsm6dsx_push_tagged_data will be reused adding
hw fifo support to st_lsm6dsx i2c embedded controller in order to
improve code readability
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c controller embedded in lsm6dx series can connect up to four
slave devices using accelerometer sensor as trigger for i2c
read/write operations.
Introduce sensor hub support for lsm6dso sensor. Add register map
for lis2mdl magnetometer sensor.
In order to perform single read/write operations st_lsm6dsx driver
relies on SLV0 channel (hw FIFO is not supported yet)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add st_lsm6dsx_sensor_set_enable routine and remove
st_lsm6dsx_sensor_{enable/disable} ones in order to make the code more
readable and remove unnecessary functions
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add ST_LSM6DSX_ID_EXT{0,1,2} sensor ids as reference for slave devices
connected to st_lsm6dsx i2c controller. Moreover introduce odr dependency
between accel and ext devices since i2c embedded controller relies on the
accelerometer sensor as bus read/write trigger so we need to enable accel
device at odr = max(accel_odr, ext_odr) in order to properly communicate
with i2c slave devices
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove static qualifier from st_lsm6dsx_set_watermark routine in
order to be reused supporting st_lsm6dsx i2c controller
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Perform a complete device reset at bootstrap reloading trimming parameter
after sw reset is completed. Device sw reset/boot is explained here:
https://www.st.com/resource/en/application_note/dm00517282.pdf,
section 5.7
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add st_lsm6dsx_update_bits_locked, st_lsm6dsx_read_locked and
st_lsm6dsx_write_locked utility routines in order to guarantee
the bus access is atomic respect to reg page configuration.
This is a preliminary patch to add i2c sensor hub support since
i2c master registers are accessed through a reg page multiplexer
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sometimes the ADC controller met some problems, and it will not complete
the data conversion, that will can not wake up the read process any more
to block users. So we should add one maximum conversion time to avoid
this issue.
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
PNI RM3100 is a high resolution, large signal immunity magnetometer,
composed of 3 single sensors and a processing chip with a MagI2C
interface.
Following functions are available:
- Single-shot measurement from
/sys/bus/iio/devices/iio:deviceX/in_magn_{axis}_raw
- Triggerd buffer measurement.
- DRDY pin for data ready trigger.
- Both i2c and spi interface are supported.
- Both interrupt and polling measurement is supported, depends on if
the 'interrupts' in DT is declared.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit add support for STMicroelectronics lis3de accelerometer.
Datasheet for this device can be found here:
https://www.st.com/resource/en/datasheet/lis3de.pdf
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for VCNL4035, which is capable of Ambient light
sensing (ALS) and proximity function. This patch adds support
only for ALS function
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this commit sensor_hub_input_attr_get_raw_value() failed to take
the signedness of 16 and 8 bit values into account, returning e.g.
65436 instead of -100 for the z-axis reading of an accelerometer.
This commit adds a new is_signed parameter to the function and makes all
callers pass the appropriate value for this.
While at it, this commit also fixes up some neighboring lines where
statements were needlessly split over 2 lines to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Channel 6 of the SAR ADC can be switched between two inputs:
SAR_ADC_CH6 input (an actual pad on the SoC) and the signal from the
temperature sensor inside the SoC.
To get usable results from the temperature sensor we need to read the
corresponding calibration data from the eFuse and pass it to the SAR ADC
registers. If the temperature sensor is not calibrated (the eFuse data
contains a bit for this) then the driver will only register the
iio_chan_spec's for voltage measurements.
This only enables the temperature sensor for the Meson8 SoC. Meson8b and
Meson8m2 SoCs can be supported in the future as well but we first need
a way to pass the fifth TSC (temperature sensor coefficient) bit to the
HHI register area (apart from that the infrastructure as already
implemented for Meson8 can be used). On the 64-bit SoCs (GXBB, GXL and
GXM) the temperature sensor inside SAR ADC is firmware-controlled (by
BL30, we can simply use the SCPI hwmon driver to get the chip
temperature).
To keep the devicetree interface backwards compatible we simply skip the
temperature sensor initialization if no eFuse nvmem cell is passed via
devicetree.
The public documentation for the SAR ADC IP block does not explain how
to use the registers to read the temperature. The logic from this patch
is based on reading and understanding Amlogic's GPL kernel sources.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Report the step range of the respective potentiometers that are
possible to userspace.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is a driver for Texas Instruments 8/10/12-bit 1-channel
compatible with DAC6311 and DAC5311 chips.
Datasheet of this chip:
http://www.ti.com/lit/ds/symlink/dac7311.pdf
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
LIS3MDL and LSM9DS1 are missing BDU settings in their register maps, so add
them. I don't have a LIS3MDL sensor to test, but this works correctly on
the LSM9DS1, which has the same register map.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update the sensor settings to support the LSM9DS1 sensor. Although the
LSM9DS1 accelerometer and gyroscope are coupled together to use the same
FIFO, the magnetometer is separate and can be cleanly supported without
refactoring the existing driver.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a comment clarifying better when to use <device_name> vs
<device_name>-magn in compatibility strings.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
More concise to have a pointer to tpl0102_cfg struct in the iio_priv
data than an integer to an index of an array.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, we enable the device before we enable the device trigger. At
high frequencies, this can cause interrupts that don't yet have a poll
function associated with them and are thus treated as spurious. At high
frequencies with level interrupts, this can even cause an interrupt storm
of repeated spurious interrupts (~100,000 on my Beagleboard with the
LSM9DS1 magnetometer). If these repeat too much, the interrupt will get
disabled and the device will stop functioning.
To prevent these problems, enable the device prior to enabling the device
trigger, and disable the divec prior to disabling the trigger. This means
there's no window of time during which the device creates interrupts but we
have no trigger to answer them.
Fixes: 90efe05562 ("iio: st_sensors: harden interrupt handling")
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Tested-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Colin Ian King
Lorenzo Bianconi
H. Nikolaus Schaller
Andy Shevchenko
Bárbara Fernandes
Fabrice Gasnier
Stefan Popa
Justin Chen
Mathieu Othacehe
Gustavo A. R. Silva
Tomasz Duszynski
Wei Yongjun
Chengguang Xu
Dragos Bogdan
Arnd Bergmann
Gwendal Grignou
Sven Van Asbroeck
Jean-Francois Dagenais
he, bo
Mike Looijmans
Jonathan Cameron
Georg Ottinger
Sergey Larin
Lars-Peter Clausen
Linus Torvalds
Greg Kroah-Hartman
Krzysztof Kozlowski
Gregory CLEMENT
Dan Carpenter
Luciana da Costa Marques
Ricardo Ribalda Delgado
Artur Rojek
Martin Kelly
Robert Eshleman
Randolph Maaßen
Daniel Drake
Lee Jones
Tomer Maimon
Sebastien Bourdelin
mario tesi
Stefan Agner
Anson Huang
Mircea Caprioru
Dan Murphy
Hans de Goede
Matt Ranostay
Aditya Pakki
Martin Blumenstingl
Kangjie Lu
YueHaibing
Andreas Brauchli
Evan Green
Jonathan Bakker
Andi Shyti
Vignesh R
Stephan Gerhold
Matheus Tavares
Lorenzo Bianconi
Chris Coffey
Nicholas Mc Guire
Slawomir Stepien
Freeman Liu
Song Qiang
Heiko Stuebner
Parthiban Nallathambi
Kuninori Morimoto
Charles-Antoine Couret